This allows devices supporting DPP protocol version 2 or newer to
provision networks that enable both the legacy (PSK/SAE) and DPP
credentials.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Share a single parsing implementation for both hostapd and
wpa_supplicant to avoid code duplication. In addition, clean up the
implementation to be more easily extensible.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use this new message from Enrollee to Configurator to indicate result of
the config object provisioning if both devices support protocol version
2 or newer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Send out the new Protocol Version attribute in Authentication
Request/Response messages and determine the peer version based on this
attribute.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This subcommand is used to update Zigbee state and specified WLAN
durations to enhance success ratio of Zigbee joining network. The
attributes defined in enum qca_mpta_helper_vendor_attr are used to
deliver these parameters to the driver.
Signed-off-by: stonez <stonez@codeaurora.org>
Peer rate statistics is per-peer cached data in the driver. These
statistics needs to be flushed to a user space application on
synchronous/asynchronous events. This command is used as an event from
the driver to flush per-peer cached statistics to the application.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new QCA vendor specific feature capability indication for the
device to indicate the support of TWT.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The current/default behavior of set blacklist BSSID QCA vendor command
is a mandate to the driver - do not consider this BSSID for connect/roam
till reset.
There are use cases where this need not be a mandate and thus could
provide the flexibility for the driver to consider this BSSID if there
are no better ones. Such use cases can use this new flag attribute to
only hint the blacklist of a BSSID to the driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not start SAE authentication from scratch when the AP requests
anti-clogging token to be used. Instead, use the previously generated
PWE as-is if the retry is for the same AP and the same group. This saves
unnecessary processing on the station side in case the AP is under heavy
SAE authentiation load.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
According to IEEE Std 802.11-2016, 9.4.2.25 when fields of an RSNE are
not included, the default values are used. The cipher suite defaults
were hardcoded to CCMP in the previous implementation, but the default
is actually different for DMG: GCMP (per 9.4.2.25.2).
It is not possible to find out from the RSNE if the network is non-DMG
or DMG, so callers of wpa_parse_wpa_ie_rsn() need to handle this case
based on context, which can be different for each caller.
In order to fix this issue, add flags to the wpa_ie_data indicating
whether pairwise/group ciphers were included in the RSNE. Callers can
check these flags and fill in the appropriate ciphers. The
wpa_parse_wpa_ie_rsn() function still initializes the ciphers to CCMP by
default so existing callers will not break. This change also fixes some
callers which need to handle the DMG network case.
Signed-off-by: Lior David <liord@codeaurora.org>
This new QCA vendor attribute adds provision to specify the
ethernet protocol id from userspace to the packets which are
offloaded to the driver/firmware (e.g., IPv4, IPv6).
Signed-off-by: Arun Kumar Khandavalli <akhandav@codeaurora.org>
The new sae_password parameter [|vlanid=<VLAN ID>] can now be used to
assign stations to a specific VLAN based on which SAE Password
Identifier they use. This is similar to the WPA2-Enterprise case where
the RADIUS server can assign stations to different VLANs and the
WPA2-Personal case where vlanid parameter in wpa_psk_file is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow user space applications to check whether wlan firmware is alive
through an nl80211 vendor command.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The change is bigger because here we need to catch the error
condition if the last element doesn't fit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rather than always iterating elements from frames with pure
u8 pointers, add a type "struct element" that encapsulates
the id/datalen/data format of them.
Then, add the element iteration macros
* for_each_element
* for_each_element_id
* for_each_element_extid
which take, as their first 'argument', such a structure and
iterate through a given u8 array interpreting it as elements.
While at it also add
* for_each_subelement
* for_each_subelement_id
* for_each_subelement_extid
which instead of taking data/length just take an outer element
and use its data/datalen.
Also add for_each_element_completed() to determine if any of
the loops above completed, i.e., it was able to parse all of
the elements successfully and no data remained.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not use a separate enum for MBO WNM-Notification Request frame
subtype values since these share the same number space with the Hotspot
2.0 ones.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previously used value 2 was already assigned for another purpose
(MBO non-preferred channel report), so the newer T&C Acceptable
definition needs to be updated with a unique value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This new QCA vendor attribute indicates the EVM value in netlink.
Signed-off-by: stonez <stonez@codeaurora.org>
:100644 100644 ad5dac2... ede4fc8... M src/common/qca-vendor.h
The vendor command QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY was defined
to carry the list of avoid frequencies that aim to avoid any
interference with other coexistencies. This recommendation was followed
strictly by trying to prevent WLAN traffic on the impacted channels.
This commit refines the expectation of the interface by defining this
avoid channel list to allow minimal traffic but not heavier one. For
example, P2P may still be able to use avoid list frequencies for P2P
discovery and GO negotiation if the actual group can be set up on a not
impact channel.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support for configuring parameters for the MU EDCA Parameter Set
element per IEEE P802.11ax/D3.0.
Signed-off-by: Siva Mullati <siva.mullati@intel.com>
Define QCA vendor command attributes to configure HE +HTC support and
HE operating mode control transmission. This is used to configure the
testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These are not allowed in ISO C++ (and well, not really in ISO C either,
but that does not result in compiler warning without pedantic
compilation).
Since ieee802_11_common.h may end up getting pulled into C++ code for
some external interfaces, it is more convenient to keep it free of these
cases. Pull in ieee802_11_defs.h to get enum phy_type defined and move
enum chan_width to common/defs.h (which was already pulled in into
src/drivers/driver.h and src/common/ieee802_11_common.h).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
While the AP is configured to enable both FT-PSK and WPA-PSK, an HP
printer request both AKMs (copied from AP?) in Association Request
frame, but don't add MDIE and don't use FT. This results in the
connection failing.
Next in logs we see:
RSN: Trying to use FT, but MDIE not included
IE - hexdump(len=26): 30 18 01 00 00 0f ac 04 01 00 00 0f ac 04
02 00 00 0f ac 02 00 0f ac 04 00 00
This is seen with some HP and Epson printers. Work around this by
stripping FT AKM(s) when MDE is not present and there is still a non-FT
AKM available.
Signed-off-by: Janusz Dziedzic <janusz@plumewifi.com>
The Android-specific chmod and chown operations on the client socket
(for communication with wpa_supplicant) did not protect against file
replacement between the bind() and chmod()/chown() calls. If the
directory in which the client socket is created (depends a bit on the
version and platform, but /data/misc/wifi/sockets is commonly used)
allows write access to processes that are different (less privileged)
compared to the process calling wpa_ctrl_open2(), it might be possible
to delete the socket file and replace it with something else (mainly, a
symlink) before the chmod/chown operations occur. This could have
resulted in the owner or permissions of the target of that symlink being
modified.
In general, it would be safest to use a directory which has more limited
write privileges (/data/misc/wifi/sockets normally has 'wifi' group
(AID_WIFI) with write access), but if that cannot be easily changed due
to other constraints, it is better to make wpa_ctrl_open2() less likely
to enable this type of race condition between the operations.
Replace chown() with lchown() (i.e., a version that does not dereference
symlinks) and chmod() with fchmod() on the socket before the bind() call
which is also not going to dereference a symlink (whereas chmod()
would). lchown() is a standard operation, but the fchmod() on the socket
is less so (unspecified behavior in some systems). However, it seems to
work on Linux and in particular, on Android, where this code is
executed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds checks to common code to verify supported bandwidth options
for each channel using nl80211-provided info. No support of additional
modes is added, just additional checks. Such checks are needed because
driver/hardware can declare more strict limitations than declared in the
IEEE 802.11 standard. Without this patch hostapd might select
unsupported channel and that will fail because Linux kernel does check
channel bandwidth limitations.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
The new ieee802_11_ext_capab() and wpa_bss_ext_capab() functions can be
used to check whether a specific extended capability bit is set instead
of having to implement bit parsing separately for each need.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE P802.11-REVmd/D2.0, 9.4.2.20.7 (Beacon request) and 9.4.2.21.7
(Beacon report) add the Last Beacon Report Indication subelement to
Beacon Request and Beacon Report elements.
Add the Last Beacon Report Indication subelement to all Beacon Report
elements if the Beacon Request indicated that this subelement is
requested.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When the frame body subelement would cause the measurement report
element to exceed the maximum element size, the frame body subelement
used to be truncated. In addition, some elements were always truncated
in order to keep the reported frame body short (e.g. RSN IE).
Alternatively, IEEE P802.11-REVmd/D2.0, 9.4.2.21.7 extension to Beacon
reporting can be used: The frame body subelement is fragmented across
multiple beacon report elements, and the reported frame body fragment ID
subelement is added.
Use beacon report fragmentation instead of truncating the frame body
as this method gives the AP a more complete information about the
reported APs.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
In 2013 or so, IFNAME=foo was prepended to at least the Unix socket
communication from wpa_supplicant to wpa_cli. This broke the (fragile)
logic that made ping/pong work more often when wpa_supplicant is busy
sending logging info to wpa_cli.
Adding check for IFNAME=foo makes this work better.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Legacy ioctl() through SIOCDEVPRIVATE are deprecated. Follow the
approach taken by bridge-utils and make use of new bridge ioctl's
whenever possible.
For example, using legacy ioctl() breaks dynamic VLAN mode on 32-bit
Linux systems running 64-bit kernels.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
An AP might refuse to connect a STA if it has a low RSSI. In such case,
the AP informs the STA with the desired RSSI delta and a retry timeout.
Any subsequent association attempt with that AP (BSS) should be avoided,
unless the RSSI level improved by the desired delta or the timeout has
expired.
Defined in Wi-Fi Alliance Optimized Connectivity Experience technical
specification v1.0, section 3.14 (RSSI-based association rejection
information).
Signed-off-by: Beni Lev <beni.lev@intel.com>
This new QCA vendor command is used to query the supported AKM suite
selectors from the driver. There has been no such capability indication
from the driver and thus the current user space has to assume the driver
to support all the AKMs. This may be the case with some drivers (e.g.,
mac80211-based ones) but there are cfg80211-based drivers that implement
SME and have constraints on which AKMs can be supported (e.g., such
drivers may need an update to support SAE AKM using
NL80211_CMD_EXTERNAL_AUTH). Allow such drivers to specify the exact set
of supported AKMs so that user space tools can determine what network
profile options should be allowed to be configured. This command returns
the list of supported AKM suite selectors in the attribute
NL80211_ATTR_AKM_SUITES.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Looks like LibreSSL 2.8 pulled in the OpenSSL API change to mark the
first argument to X509_ALGOR_get0() const.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The purpose of Multi-AP specification is to enable inter-operability
across Wi-Fi access points (APs) from different vendors.
This patch introduces one new configuration parameter 'multi_ap' to
enable Multi-AP functionality and to configure the BSS as a backhaul
and/or fronthaul BSS.
Advertise vendor specific Multi-AP capabilities in (Re)Association
Response frame, if Multi-AP functionality is enabled through the
configuration parameter.
A backhaul AP must support receiving both 3addr and 4addr frames from a
backhaul STA, so create a VLAN for it just like is done for WDS, i.e.,
by calling hostapd_set_wds_sta(). Since Multi-AP requires WPA2 (never
WEP), we can safely call hostapd_set_wds_encryption() as well and we can
reuse the entire WDS condition.
To parse the Multi-AP Extension subelement, we use get_ie(): even though
that function is meant for parsing IEs, it works for subelements.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Include an OCI element in SA Query Request and Response frames if OCV
has been negotiated.
On Linux, a kernel patch is needed to let clients correctly handle SA
Query Requests that contain an OCI element. Without this patch, the
kernel will reply to the SA Query Request itself, without verifying the
included OCI. Additionally, the SA Query Response sent by the kernel
will not include an OCI element. The correct operation of the AP does
not require a kernel patch.
Without the corresponding kernel patch, SA Query Requests sent by the
client are still valid, meaning they do include an OCI element.
Note that an AP does not require any kernel patches. In other words, SA
Query frames sent and received by the AP are properly handled, even
without a kernel patch.
As a result, the kernel patch is only required to make the client properly
process and respond to a SA Query Request from the AP. Without this
patch, the client will send a SA Query Response without an OCI element,
causing the AP to silently ignore the response and eventually disconnect
the client from the network if OCV has been negotiated to be used.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
ocv_verify_tx_params() verifies that the receive OCI element includes
field values that are compatible with the local channel configuration.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This adds two utility functions to convert both operating classes and
and the chan_width enum to an integer representing the channel
bandwidth. This can then be used to compare bandwidth parameters in an
uniform manner.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This function can be used to easily convert the parameters returned
by the channel_info driver API, into their corresponding operating
class and channel number.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Also add the ChangeLog entries for both hostapd and wpa_supplicant to
describe main changes between v2.6 and v2.7.
Signed-off-by: Jouni Malinen <j@w1.fi>
The reverse case (local identifier configured but no identifier
received) was already covered, but PKEX is not going to complete
successfully if there is any difference in identifier configuration, so
ignore this other case as well. This avoids unnecessary responses to
PKEX requests with identifier from a device that is ready for PKEX in
general, but not for that particular request.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit enhances QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES to
also be an event, aimed to notify the link status (EX: connected
stations status on an AP link).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
A local memory allocation failuring during GAS Comeback Response frame
generation could result in freeing the response context without removing
it from the list. This would result in dereferencing freed memory when
processing the next comeback request.
Signed-off-by: Jouni Malinen <j@w1.fi>
If local memory allocation for the GAS response failed, couple of error
paths ended up leaking some memory maintaining the state for the
exchange. Fix that by freeing the context properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Parse the OSEN IE from the AP to determine values used in the AssocReq
instead of using hardcoded cipher suites. This is needed to be able to
set the group cipher based on AP advertisement now that two possible
options exists for this (GTK_NOT_USED in separate OSEN BSS; CCMP or
GTK_NOT_USED in shared BSS case). Furthermore, this is a step towards
allowing other ciphers than CCMP to be used with OSEN.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG vendor command
to set the priorities among different types of traffic of
WLAN/BT/Zigbee during coex scenarios.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add interface for drivers to report changes in TX/RX throughput
dynamically to user space. This information can be used by userspace
tools to tune kernel's TCP parameters in order to achieve peak
throughput. The driver may optionally provide guidance on which TCP
parameters to be configured for optimal performance along with the
values to be configured.
The TCP parameters that need to be tuned for peak performance are not
interface specific. Based on the guidance from the driver and
considering the other interfaces that may be affected with the new
configurations, a userspace tool has to choose the values to be
configured for these parameters to achieve optimal performance across
interfaces.
The throughput levels informed by the driver with this event are only
for providing guidance on TCP parameter tuning from userspace. The
driver may change the thresholds used to decide low or medium or high
throughput levels based on several parameters based on the PHY layer
capacity in the current connection, the number of packets being
dispatched per second, or the number of packets pending in queues, etc.
The throughput levels may not be consistent with the actual throughput
of the link.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure action
frame transmission in HE trigger based PPDU.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure HE
single user PPDU transmission.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attributes to configure HE
operating mode control field bandwidth, number of spatial streams, and
UL MU disable configuration. Define a new attribute to clear the
previously set HE OM control field configuration. This is used for
testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support for negotiating WNM Collocated Interference Reporting. This
allows hostapd to request associated STAs to report their collocated
interference information and wpa_supplicant to process such request and
reporting. The actual values (Collocated Interference Report Elements)
are out of scope of hostapd and wpa_supplicant, i.e., external
components are expected to generated and process these.
For hostapd/AP, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration. STAs are requested to perform
reporting with "COLOC_INTF_REQ <addr> <Automatic Report Enabled> <Report
Timeout>" control interface command. The received reports are indicated
as control interface events "COLOC-INTF-REPORT <addr> <dialog token>
<hexdump of report elements>".
For wpa_supplicant/STA, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration and setting Collocated
Interference Report Elements as a hexdump with "SET coloc_intf_elems
<hexdump>" control interface command. The hexdump can contain one or
more Collocated Interference Report Elements (each including the
information element header). For additional testing purposes, received
requests are reported with "COLOC-INTF-REQ <dialog token> <automatic
report enabled> <report timeout>" control interface events and
unsolicited reports can be sent with "COLOC_INTF_REPORT <hexdump>".
This commit adds support for reporting changes in the collocated
interference (Automatic Report Enabled == 1 and partial 3), but not for
periodic reports (2 and other part of 3).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add NAN NDP attribute QCA_WLAN_VENDOR_ATTR_PEER_NDPE_SUPPORT which
indicates if NDP remote peer supports NDPE attribute or not.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a subcommand for Channel Frequency Response (CFG) Capture
Configuration and define attributes for configuring CFR capture
parameters per peer and enabling/disabling CFR capture.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend hostapd to allow the new OSU Provider NAI List ANQP-element to be
advertised in addition to the previously used OSU Providers list
ANQP-element. The new osu_nai2 configurator parameter option is used to
specify the OSU_NAI value for the shared BSS (Single SSID) case while
osu_nai remains to be used for the separate OSU BSS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Driver/firmware does roam scan when it finds the need to roam to a
different BSS. Add a QCA vendor event to indicate such roam scan events
from driver/firmware to user space.
Please note that some drivers may not send these events in few cases,
e.g., if the host processor is sleeping when this event is generated in
firmware to avoid undesired wakeups.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The temporary EC_POINT 'sum' needs to be freed at the end of the
function with the other OpenSSL allocations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It looks like at least OpenSSL 1.1.0i includes the extra checks in
EC_POINT_set_affine_coordinates_GFp() that break the previously used
mechanism for generating invalid keys. Fix this by using the alternative
design that was used with OpenSSL 1.1.1 and BoringSSL.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Parse the Venue URL ANQP-element payload and report it with the new
RX-VENUE-URL event messages if the query was done using PMF.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new QCA vendor specific test config attribute to configure the
support for receiving the MPDU with operating mode control subfield.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This enhances DPP_AUTH_INIT, DPP_CONFIGURATOR_SIGN, and SET
dpp_configurator_params to allow optional setting of the DPP groupId
string for a Connector. If the value is not set, the previously wildcard
value ("*") is used by default.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The payload used for the existing NAN vendor command,
QCA_NL80211_VENDOR_SUBCMD_NAN is a binary blob of data. This
command is not extendable to send additional information. Hence
define a new vendor command QCA_NL80211_VENDOR_SUBCMD_NAN_EXT,
that can carry the binary blob encapsulated within an attribute
and can carry additional attributes to enhance the NAN command
interface. Define additional 3 new attributes for conveying
type of NAN subcmd and channel information.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Present implementation of NAN vendor command does not use
attribute encapsulation for sending the command from userspace
to the driver, payload is directly sent as is. Attribute
QCA_WLAN_VENDOR_ATTR_NAN is used only for receiving vendor
events in the userspace from the driver. Update the doc as per
this implementation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The max supported ADDBA buffer size value is 256, so change
the buffer size attribute type to U16 to configure the testbed
device to use the 256 buffer size in ADDBA negotiation in 11ax
testing.
This attribute is used only to configure a testbed device and the old
definition of this attribute was not used in any deployed implementation
hence it is still justifiable to change the definition.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_BLACKLIST_BSSID to get maximum
blacklist BSSIDs capability from the driver for gscan.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
GCM-AES-256 cipher suite is defined in IEEE Std 802.1AEbn-2011.
If authenticator configured as GCM-AES-256, the distributed SAK will be
256 bits indicated by the GCM-AES-256 ID in the MKA packet.
This patch will make AES Key Unwrap to 32 bytes of SAK when identify the
ID.
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Add a new test config QCA vendor attribute to override the MU EDCA
parameters to default values in the driver for test configuration. This
is used for configuring the testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure HE
trigger frame MAC padding duration value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attributes to configure
HE MU EDCA parameters value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure Tx
beamformee number of space-time streams value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The AKM 00-0F-AC:13 is supposed to use cryptographic algorithms
consistently, but the current IEEE 802.11 standard is not doing so for
the key names: PMKID (uses SHA-1), PMKR0Name/PMKR1Name (uses SHA-256).
The PMKID case was already implemented with SHA-384 and this commit
replaces use of SHA-256 with SHA-384 for PMKR0Name/PMKR1Name derivation
to be consistent in SHA-384. While this is not compliant with the
current IEEE 802.11 standard, this is clearly needed to meet CNSA Suite
requirements. Matching change is being proposed in REVmd to get the IEEE
802.11 standard to meet the use case requirements.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This defines key lengths for SHA384-based FT AKM and handles writing and
parsing for RSNE AKMs with the new value.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit adds a new vendor command attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_GTX in
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION to enable/disable green
Tx power saving feature.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends the SAE implementation in both infrastructure and mesh BSS
cases to allow an optional Password Identifier to be used. This uses the
mechanism added in P802.11REVmd/D1.0. The Password Identifier is
configured in a wpa_supplicant network profile as a new string parameter
sae_password_id. In hostapd configuration, the existing sae_password
parameter has been extended to allow the password identifier (and also a
peer MAC address) to be set. In addition, multiple sae_password entries
can now be provided to hostapd to allow multiple per-peer and
per-identifier passwords to be set.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add NAN attributes to communicate IPv6 address, port, and protocol
between wifihal and host driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Over time a number of style issues have crept into qca-vendor.h,
so fix most of them. There are some identifiers and comments which
exceed 80 columns, but these are left as-is for readability.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This can be used to determine which mechanism to use for configuring
country code from trusted sources.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure Tx
beamformee in the driver. This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
OpenSSL started reporting failures from
EC_POINT_set_affine_coordinates_GFp() similarly to BoringSSL, so use the
same workaround to enable this protocol testing case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add commands to allow an AP to configure filtering rules to capture
frames from stations that are active on the operating channel, but
not associated to this AP. Operations include add/delete the filter
and get the statistics information of the unassociated stations.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Extend RADIUS DAS to support CoA-Request packets for the case where the
HS 2.0 Terms And Conditions filtering VSA is used to remove filtering.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Mark a channel as required DFS based on regulatory information received
from the driver/kernel rather than deciding based on hardcoded
boundaries on the frequency. Previously few channels were being marked
as requiring DFS even though they were non-DFS in a particular country.
If the driver does not provide channel list information, fall back to
the previously used frequency-based determination.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend wpa_supplicant WNM-Notification RX handling to parse and process
received Terms and Conditions Acceptance notifications. If PMF is
enabled for the association, this frame results in control interface
indication (HS20-T-C-ACCEPTANCE <URL>) to get upper layers to guide the
user through the required acceptance steps.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd Access-Accept processing to check if the RADIUS
server indicated that Terms and Conditions Acceptance is required. The
new hs20_t_c_server_url parameter is used to specify the server URL
template that the STA is requested to visit.
This commit does not enable any kind of filtering, i.e., only the part
of forwarding a request from Access-Accept to the STA using
WNM-Notification is covered.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows user to get event indication when a new interface is
added/removed for 4addr WDS STA and also WDS STA ifname is informed
through the STA command.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
While it is unlikely that FILS would be used without PMF or SAE in the
build, it is possible to generate such a build and as such, it would be
good for the KDF selection to work properly. Add CONFIG_FILS as an
independent condition for the SHA256-based KDF. Previously, this
combination would have resulted in failure to derive keys and terminated
key management exchange.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd processing of (Re)Association Request frames to
store a local copy of the Consortium OI within the Roaming Consortium
Selection element, if present, and then add that in HS 2.0 Roaming
Consortium attribute into RADIUS Access-Request messages.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends wpa_supplicant Hotspot 2.0 ANQP routines to allow the
Operator Icon Metadata ANQP-element to be fetched with "ANQP_GET <bssid>
hs20:12". The result is available in the new hs20_operator_icon_metadata
entry in the "BSS <bssid>" output.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
At least LibreSSL v2.7.2 indicates support for OpenSSL API 1.1.0, but it
does not apparently use const ASN1_OBJECT * with X509_ALGOR_get0(). Use
the older non-const version here with LibreSSL to fix compilation.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gives more protection against unexpected behavior if RSN supplicant
code ends up trying to use sm->pmk[] with a stale value. Couple of the
code paths did not clear sm->pmk_len explicitly in cases where the old
PMK is being removed, so cover those cases as well to make sure these
will result in PMK-to-PTK derivation failures rather than use of
incorrect PMK value if such a code path could be reached somehow.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new wifi test config attribute to configure HE LTF in the
driver. This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
In the current implementation, upon an EAP method failure, followed by
an EAP failure, the EAP Status is propagated up in wpa_supplicant with a
general failure parameter string "failure". This parameter is used for a
notification on the dbus.
This commit reports the EAP method failure error code in a separate
callback.
The solution in this commit is generic to all EAP methods, and can be
used by any method that need to pass its error code. However, this
commit only implements the reporting for EAP-SIM and EAP-AKA methods
where the Notification Code (in AT_NOTIFICATION) is used as the method
specific error code value.
Signed-off-by: Ahmed ElArabawy <arabawy@google.com>
This extends the original IEEE Std 802.11ai-2016 functionality with the
changes added in REVmd to describe how additional keys are derived to
protect the FT protocol using keys derived through FILS authentication.
This allows key_mgmt=FT-FILS-SHA256 to be used with FT protocol since
the FTE MIC can now be calculated following the changes in REVmd. The
FT-FILS-SHA384 case is still unsupported (it needs support for variable
length MIC field in FTE).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous implementation ended up defaulting to using PRF-SHA1 for
deriving PTK from PMK when SAE was used. This is not correct since the
SAE AKM is defined to be using SHA-256 -based KDF instead. Fix that.
Note: This change is not backwards compatible. Both the AP and station
side implementations will need to be updated at the same time to
maintain functionality.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an event callback for EVENT_STATION_OPMODE_CHANGED to allow
user/application to get the notification whenever there is a change in a
station's HT/VHT op mode.
The new events:
STA-OPMODE-MAX-BW-CHANGED <addr> <20(no-HT)|20|40|80|80+80|160>
STA-OPMODE-SMPS-MODE-CHANGED <addr> <automatic|off|dynamic|static>
STA-OPMODE-N_SS-CHANGED <addr> <N_SS>
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
To retain configurator information across hostapd/wpa_supplicant
restart, private key need to be maintained to generate a valid pair of
authentication keys (connector, netaccess_key, csign) for new enrollees
in the network.
Add a DPP_CONFIGURATOR_GET_KEY control interface API through which the
private key of an existing configurator can be fetched.
Command format:
DPP_CONFIGURATOR_GET_KEY <configurator_id>
The output from this command can then be used with
"DPP_CONFIGURATOR_ADD key=<hexdump>" to create the same key again.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The SAE AKM 00-0F-AC:8 is supposed to use EAPOL-Key Key Descriptor
Version 0 (AKM-defined) with AES-128-CMAC and NIST AES Key Wrap.
However, the previous implementation ended up using Key Descriptor
Version 2 (HMAC-SHA-1-128 and NIST AES Key Wrap). Fix this by using the
appropriate Key Descriptor Version and integrity algorithm. Use helper
functions to keep the selection clearer and more consistent between
wpa_supplicant and hostapd uses.
Note: This change is not backwards compatible. Both the AP and station
side implementations will need to be updated at the same time to
maintain functionality.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new WiFi test configuration attributes in QCA vendor
command to configure BA session parameters and to add or
delete a BA session and to configure no ack policy.
This is used for configuring the testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new WiFi test configuration attribute in QCA vendor
command to allow or not to allow WEP/TKIP in HT/VHT/HE mode.
This is used for configuring the testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it easier to understand why "SAE: Failed to select group"
debug entry shows up in cases the selected crypto library does not
support a specific group.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
India supports 5 GHz channels 169 and 173 now. Enable HT40 across
channels 165 and 169. Leave channel 173 to remain HT20 only.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Enhance QCA vendor specific APF interface to support write/read program
and/or data and to enable/disable APF feature.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new QCA vendor sub command for configuring the device with wifi
test configuration. Add new test config attributes for this sub command
that are used to configure the device for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The blocking timeout of this function was changed from 2 seconds to 10
seconds in this commit 1480633f ("Use longer timeout in
wpa_ctrl_request()"), but the description was never changed accordingly.
Signed-off-by: Simon Dinkin <simon.dinkin@tandemg.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add new QCA vendor commands and attributes to get thermal information
and send thermal shutdown related commands. Indicates the driver to
enter the power saving mode or resume from the power saving mode based
on the given temperature and thresholds.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add additional NDP attributes and NDP subcommand value which is
provided as part of schedule update indication from driver/firmware
to HAL.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The y coordinates for some of these PKEX role-specific points were
changed in the PKEX specification, so update the implementation to
match.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allow MSDU queue depth threshold in target to be set per peer per
TID. This command contains MAC address, TID, update mask, and threshold
values.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This prevents an issue where duplicated Authentication Response frame
could have resulted in deriving a new ke value after M.x had already
been cleared. This would result in the following configuration exchange
failing. This could happen since many driver do not filter out
retransmitted Public Action frames and link layer. Furthermore, this
could have been used as a denial-of-service attack agains the DPP
exchange.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit extends the existing QCA vendor specific NUD_STATS_GET/SET
interface to also collect the statistics of the data packets. The
intention here is to get more comprehensive information to detect the
network unreachability.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit introduces a QCA vendor command that provides the current
information of WLAN hardware MAC and its associated WLAN netdev
interfaces.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Set Sc to 2^16-1 when moving to Accepted state per IEEE Std 802.11-2016,
12.4.8.6.5 (Protocol instance behavior - Confirmed state). This allows
the peer in Accepted state to silently ignore unnecessary
retransmissions of the Confirm message.
Signed-off-by: Jouni Malinen <j@w1.fi>
This implements the behavior described in IEEE Std 802.11-2016,
12.4.8.6.6 (Protocol instance behavior - Accepted state) to silently
discard received Confirm message in the Accepted state if the new
message does not use an incremented send-confirm value or if the special
2^16-1 value is used. This avoids unnecessary processing of
retransmitted Confirm messages.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf parameter sae_sync (default: 5) can now be used to
configure the dot11RSNASAESync value to specify the maximum number of
synchronization errors that are allowed to happen prior to
disassociation of the offending SAE peer.
Signed-off-by: Jouni Malinen <j@w1.fi>
A new vendor attribute QCA_WLAN_VENDOR_ATTR_GET_WEIGHED_PCL is added for
getting preferred channels with weight value and a flag to indicate how
the channels should be used in P2P negotiation process.
Signed-off-by: Peng Xu <pxu@qti.qualcomm.com>
Indicates the driver to use the RSNE as-is from the connect interface.
Exclusively used for the scenarios where the device is used as a testbed
device with special functionality and not recommended for production.
This helps driver to not validate the RSNE passed from user space and
thus allow arbitrary IE data to be used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously commit c79238b6a4 ('Define a
QCA vendor command to configure SAR Power limits') implemented a vendor
command interface to allow a userspace entity to dynamically control the
SAR power limits. Now implement a command to retrieve the current SAR
power limits.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The BoringSSL version of crypto_ecdh_init() and dpp_gen_keypair() works
fine with OpenSSL as well, so use that same implementation for both to
avoid unnecessary maintanence of multiple versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to go through EC_GROUP_new_by_curve_name(),
EC_KEY_new(), and EC_KEY_set_group() when a single call to
EC_KEY_new_by_curve_name() takes care of all that.
Signed-off-by: Jouni Malinen <j@w1.fi>
This reverts commit 5548453a2d since
BoringSSL added ECDSA_SIG_set0() and ECDSA_SIG_get0() in commit
8dc226ca8f1ef60737e1c1bf8cfcabf51d4068c7 ('Add some missing OpenSSL
1.1.0 accessors.') and updated X509_ALGOR_get0() prototype to match
OpenSSL 1.1.0 changes in commit e3b2a5d30d309091cab3e6a19dee7323c40d968d
('Const-correct X509_ALGOR_get0.').
Signed-off-by: Jouni Malinen <j@w1.fi>
A new vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL is added
for vendor sub-command QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION.
This attribute is for setting the level of WLM.
Signed-off-by: Paul Zhang <paulz@qti.qualcomm.com>
DPP Responder selects whether mutual authentication is used. This commit
adds information about that selection to upper layers (ctrl_iface event
DPP-AUTH-DIRECTION mutual=<0/1>) on the Initiator side.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends dpp_test functionality to allow DPP exchanges to be stopped
when receiving a specified message.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add QCA vendor command and attributes for vendor specific Representative
RF Operating Parameter (RROP) information. This information is intended
for optional use by external ACS. It provides guidance values for some
RF parameters that are used by the system during operation, so that
external ACS can utilize these to compare between channels, bands, etc.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
sha256_vector() result was ignored apart from printing out the failure
in the debug log. This is not really a normal case and it is better to
reject the full operation rather than try to continue with an incorrect
public key hash value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for a timeout from an old GAS server operation to
trigger DPP configuration failure during the subsequent DPP operation.
Fix this by verifying that the status callback is for the response
generated during the same DPP Authentication/Configuration exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Configurator signing its own Connector was previously supported only in
wpa_supplicant. This commit extends that to hostapd to allow an AP
acting as a Configurator to self-configure itself.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of using the all-zeros Initiator Bootstrapping Key Hash when no
local bootstrapping key is configuref for the Initiator, automatically
generate a temporary bootstrapping key for the same curve that the
Responder uses. If the Responder indicates that it wants to do mutual
authentication, provide the URI for the auto-generated bootstrapping key
in the DPP-RESPONSE-PENDING event for upper layers to display the QR
Code.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 03abb6b541 ('DPP: Reject unexpected
Req/Resp message based on Auth/PKEX role') used incorrect type of error
value (NULL vs. -1). Fix that.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external applications to get event indication for Probe
Request frames. Extend ctrl iface cmd "ATTACH" to enable this event on
per-request basis. For example, user has to send ctrl iface cmd "ATTACH
probe_rx_events=1" to enable the Probe Request frame events.
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
If unicast Authentication Request frame is used and the peer ACKs such a
frame, but does not reply within the two second limit, there is no need
to continue trying to retransmit the request frames since the peer was
found, but not responsive.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new conf={sta,ap}-{sae,psk-sae} parameter values can now be used to
specify that the legacy configuration object is for SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows DPP to be used for enrolling credentials for SAE networks in
addition to the legacy PSK (WPA-PSK) case. In addition, enable FT-PSK
and FT-SAE cases automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Retransmit the PKEX Exchange Request frame if no response from a peer is
received. This makes the exchange more robust since this frame is sent
to a broadcast address and has no link layer retries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to allow more invalid attribute values to be written
into Peer Discovery Request/Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to cover a case where Config Attrib Object value is
invalid in Configuration Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to cover cases where DPP Status value is invalid in
Authentication Response/Confirm frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to cover cases where Initiator/Responder Bootstrap Key
Hash value in DPP Authentication frames is invalid (flip one bit).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends dpp_test to allow invalid Initiator/Responder Protocol Key
to be written into the Authentication Request/Response frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Unlike OpenSSL, BoringSSL returns an error from
EC_POINT_set_affine_coordinates_GFp() is not on the curve. As such, need
to behave differently here depending on which library is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While the OpenSSL version of i2d_EC_PUBKEY() seemed to be able to use
the POINT_CONVERSION_COMPRESSED setting on the EC key, that did not seem
to work with BoringSSL. Since this is not exactly robust design, replace
use of i2d_EC_PUBKEY() with a custom routine that enforces the DPP rules
on SubjectPublicKeyInfo (compressed format of the public key,
ecPublicKey OID, parameters present and indicating the curve by OID).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This routine was previously implemented twice using i2d_EC_PUBKEY().
There is no need to duplicate that implementation and especially since
it looks like this implementation needs to be replaced for BoringSSL,
start by using a shared helper function for both locations so that there
is only a single place that uses i2d_EC_PUBKEY() to build the special
DPP bootstrapping key DER encoding.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like BoringSSL claims to have OPENSSL_VERSION_NUMBER for a
1.1.0 version, but it does not provide ECDSA_SIG_set0() or
ECDSA_SIG_get0(). For now, add the helper functions regardless of the
version BoringSSL claims to be. Similarly, include the X509_ALGOR_get0()
workaround unconditionally for BoringSSL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Fix the block comment style issue introduced as part of commit
fbfceef3af ("Add QCA vendor commands for
spectral scan").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add sub-command QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING to flush
pending packets in firmware. The attributes are listed in enum
qca_wlan_vendor_attr_flush_pending. The QCA_WLAN_VENDOR_ATTR_PEER_ADDR
specifies the peer MAC address and the QCA_WLAN_VENDOR_ATTR_AC specifies
the access category of the pending packets.
Signed-off-by: Lin Tingting <tinlin@qti.qualcomm.com>
A new vendor attribute QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU
is added for vendor sub-command QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET.
This attribute is for pending MSDUs corresponding to respective AC.
Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
../src/common/dpp.c: In function 'dpp_test_gen_invalid_key':
../src/common/dpp.c:5531:10: warning: return makes integer from pointer without a cast [-Wint-conversion]
return NULL;
^
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
There should be no wpa_pmk_to_ptk() calls with the cipher argument
indicating a cipher that is not allowed as a pairwise cipher. However,
it looks like that was possible to happen with wlantest. Check for this
corner case explicitly to avoid generating confusing debug logs.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is for protocol testing to check what happens if the Responser
receives an unexpected Authentication Response instead of Authentication
Confirm.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This prevents issues where an unexpected message in the DPP
Authentication exchange or PKEX could result in undefined behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant DPP implementation to retransmit DPP
Authentication Response frame every 10 seconds up to 5 times if the peer
does not reply with DPP Authentication Confirm frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new role=either parameter can now be used with DPP_AUTH_INIT to
indicate that the initiator can take either the Configurator or Enrollee
role.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant to iterate over all available channels from
the intersection of what the peer indicates and the local device
supports when initiating DPP Authentication. In addition, retry DPP
Authentication Request frame up to five times if no response is
received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add the following vendor commands and their vendor attributes for
spectral scan.
1) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG
Get current values of spectral parameters.
2) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS
Get stats for spectral scan debug.
3) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO
Get the spectral hardware capability.
4) QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS
Get the current status of spectral scan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME
and QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME to record
timestamp and duration for the last MAC counters. Some user layer
application is delay sensitive. It needs to know time stamp and
measurment duration for the counters.
Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
K and z can be derived already based on information available at the
time the PKEX Exchange Request is being processed, so move these there
from the PKEX Commit-Reveal Request processing since that matches the
DPP tech spec description close and allows PKEX exchange to be aborted
earlier if anything unexpected happens.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add limit on number of failed attempts that could have used PKEX code.
If the limit (5) is reached, drop the PKEX state (including the code)
and report this on the control interface to indicate that a new code
needs to be entered due to possible attack.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Clean up the pending PKEX exchange if Commit-Reveal Request processing
indicates a mismatch in the PKEX code. Previously, the this case was
silently ignored and the session was left in pending state that
prevented new PKEX exchanges from getting initated. Now, a new attempt
is allowed to be initiated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Number of places writing BIGNUM values with left-padding were open
coding this helper functionality unnecessarily.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Report mismatching finite cyclic group with PKEX Exchange Response using
STATUS_BAD_GROUP and provide more detailed error report over the control
interface on the peer device when this happens.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The optional channel information was removed from the discovery object
in the DPP tech spec, so no need to maintain this TODO note anymore.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up dpp_pkex_rx_commit_reveal_req() a bit and makes it easier
to add protocol testing functionality to PKEX exchange similarly to the
previously added DPP Authentication case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up dpp_pkex_rx_exchange_resp() a bit and makes it easier to
add protocol testing functionality to PKEX exchange similarly to the
previously added DPP Authentication case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up dpp_pkex_rx_exchange_req() a bit and makes it easier to
add protocol testing functionality to PKEX exchange similarly to the
previously added DPP Authentication case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Indicate to upper layers if PKEX Commit-Reveal Request frame AES-SIV
decryption fails. That is a likely sign of the PKEX code mismatch
between the devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This provides access to the Minimum/Maximum Transmit Power Capabilitie
fileds (the nominal minimum/maximum transmit power with which the STA
is capable of transmitting in the current channel; signed integer in
units of decibels relative to 1 mW).
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
Allow the Initiator to request a different channel to be used for DPP
Authentication and DPP Configuration exchanges. This commit adds support
for this in wpa_supplicant with the optional neg_freq=<freq in MHz>
parameter in DPP_AUTH_INIT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Process Authentication Confirm with the two failure cases defined in the
spec: STATUS_NOT_COMPATIBLE and STATUS_AUTH_FAILURE. This verifies the
{R-nonce}k2 part and reports more detailed failure reason if the message
is valid.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If Authentication Response processing fails due to R-capab
incompatibility or R-auth mismatch, send Authentication Confirm with
error status.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the dpp_test mechanism to allow I-nonce, R-capab, R-auth,
and I-auth values in Authentication Response/Confirm to use incorrect
values.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, Initiator decided whether to use mutual authentication on
its own based on having own and peer bootstrapping info. This prevented
Responder from selecting not to use mutual authentication in such a
case. Fix this by allowed Initiator to fall back to non-mutual
authentication based on Responder choice if the bootstrapping mechanism
allows this (PKEX does not; it mandates use of mutual authentication).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the dpp_test mechanism to allow each of the required
attributes in Authentication Confirm to be omitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the dpp_test mechanism to allow each of the required
attributes in Authentication Response to be omitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up old dpp_auth_build_resp() (now dpp_auth_build_resp_ok())
a bit by separating initialization steps for a DPP authentication
session from the code needed to build the frame. This allows
dpp_auth_build_resp_status() to share the helper function instead of
having to maintain a duplicated message construction implementation. In
addition, this makes it easier to remove some of the attributes for
protocol testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the dpp_test mechanism to allow each of the required
attributes in Authentication Request to be omitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up dpp_auth_init() a bit by separating initialization steps
for a DPP authentication session from the code needed to build the
frame. In addition, this makes it easier to remove some of the
attributes for protocol testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Both the DPP-TX and DPP-TX-STATUS events are provided.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that dpp_check_attrs() takes care of verifying that no attributes
are after the Wrapped Data attribute, the duplicated checks in hostapd
and wpa_supplicant side of the implementation can be removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a generic mechanism for configuring the DPP implementation to behave
in particular different (mostly incorrect) ways for protocol testing
purposes. The new dpp_test parameter can be set to a non-zero integer to
indicate a specific behavior. This is only available in
CONFIG_TESTING_OPTIONS=y builds.
This commit include cases for an extra attribute being added after the
Wrapped Data attribute and Initiator/Responder capabilities having an
unexpected zero capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While using an external RADIUS server SUCCESS messages were not being
sent (internal was fine). Also add event messages for other states that
others might find useful, and consistency between the two.
Signed-off-by: Michael Baird <Michael.Baird@ecs.vuw.ac.nz>
Add additional attributes to specify the PMK, PMKID, and the ERP next
sequence number to the vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH. These are needed in case
of an offloaded FILS roaming.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that TK, KCK, and KEK lengths are set to consistent values within
struct wpa_ptk before using them in supplicant. This is an additional
layer of protection against unexpected states.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of setting the default PMK length for the cleared PMK, set the
length to 0 and explicitly check for this when deriving PTK to avoid
unexpected key derivation with an all-zeroes key should it be possible
to somehow trigger PTK derivation to happen before PMK derivation.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
Properly track whether a PTK has already been installed to the driver
and the TK part cleared from memory. This prevents an attacker from
trying to trick the client into installing an all-zero TK.
This fixes the earlier fix in commit
ad00d64e7d ('Fix TK configuration to the
driver in EAPOL-Key 3/4 retry case') which did not take into account
possibility of an extra message 1/4 showing up between retries of
message 3/4.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Track the current GTK and IGTK that is in use and when receiving a
(possibly retransmitted) Group Message 1 or WNM-Sleep Mode Response, do
not install the given key if it is already in use. This prevents an
attacker from trying to trick the client into resetting or lowering the
sequence counter associated to the group key.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Memory allocation failures could have resulted in error paths that
dereference a NULL pointer or double-freeing memory. Fix this by
explicitly clearing the freed pointer and checking allocation results.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows CONFIG_TESTING_OPTIONS=y builds of wpa_supplicant to
override the OWE DH Parameters element in (Re)Association Request frames
with arbitrary data specified with the "VENDOR_ELEM_ADD 13 <IE>"
command. This is only for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This additional field was added to DPP Public Action frames in DPP tech
spec v0.2.3 to support cryptographic agility in the future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This matches the change in the DPP tech spec to make this less likely to
be confused with the shared secret z.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The Key MIC field value got truncated for all cases and incorrect HMAC
hash algorithm was used for the SHA512 cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the helper functions for determining OWE key lengths and
Key MIC values to support other DH curves beyond the mandatory group 19.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new owe_transition_bssid and owe_transition_ssid parameters can be
used to configure hostapd to advertise the OWE Transition Mode element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Replace vendor-specific elements for HE capabilities and HE operation
elements with the P802.11ax defined element values. This version is
based on P802.11ax/D1.4.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add 802.11ax channel property flags for use with external ACS (QCA
vendor command). Use the remaining available bits in
qca_wlan_vendor_channel_prop_flags for the first few 11ax flags. Then
add qca_wlan_vendor_channel_prop_flags_2 as a continuation of
qca_wlan_vendor_channel_prop_flags and add the remaining 11ax flags
there. Note that qca_wlan_vendor_channel_prop_flags_ext is not used
since it is currently not intended for holding such information. Rather
it is meant for holding additional control information related to
features such as DFS, CSA, etc.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The FILS features on STA needs to be disabled for testing purposes to
verify the APUT behavior with non-FILS STAs. Add a QCA vendor attribute
for doing so.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These control interface event messages can be used to allow hostapd AP
to be configured for legacy WPA2-Personal configuration with DPP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This part is missing from IEEE Std 802.11ai-2016, but the lack of DHss
here means there would not be proper PFS for the case where PMKSA
caching is used with FILS SK+PFS authentication. This was not really the
intent of the FILS design and that issue was fixed during REVmd work
with the changes proposed in
https://mentor.ieee.org/802.11/dcn/17/11-17-0906-04-000m-fils-fixes.docx
that add DHss into FILS-Key-Data (and PTK, in practice) derivation for
the PMKSA caching case so that a unique ICK, KEK, and TK are derived
even when using the same PMK.
Note: This is not backwards compatible, i.e., this breaks PMKSA caching
with FILS SK+PFS if only STA or AP side implementation is updated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11ai-2016 had missed a change in the Pairwise key hierarchy
clause (12.7.1.3 in IEEE Std 802.11-2016) and due to that, the previous
implementation ended up using HMAC-SHA-1 -based PMKID derivation. This
was not really the intent of the FILS design and that issue was fixed
during REVmd work with the changes proposed in
https://mentor.ieee.org/802.11/dcn/17/11-17-0906-04-000m-fils-fixes.docx
that change FILS cases to use HMAC-SHA-256 and HMAC-SHA-384 based on the
negotiated AKM.
Update the implementation to match the new design. This changes the
rsn_pmkid() function to take in the more generic AKMP identifier instead
of a boolean identifying whether SHA256 is used.
Note: This is not backwards compatible, i.e., this breaks PMKSA caching
based on the initial ERP key hierarchy setup if only STA or AP side
implementation is updated. PMKSA caching based on FILS authentication
exchange is not impacted by this, though.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was previously defined inconsistently (H() vs. SHA256()), but it is
now clarified in the draft tech spec to use SHA256(), so update
implementation to do that.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DPP tech spec changed the contents of these frames by replacing the
public key hash attributes with a Transaction ID attribute that gets
copied from the request to the response to identify the transaction in a
simpler manner.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is an event indicating to the user space that the driver has
detected an internal failure. The driver is expected to recover from
such a failure automatically, e.g., by resetting the device. This event
carries the information indicating the reason that triggered this
detection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The two channel width bits in the VHT capability field can be decoded in
following values (IEEE Std 802.11ac-2013 8.4.2.160.2 VHT Capabilities
Info field):
* 0: no 160 or 80+80 MHz support
* 1: 160 MHz support
* 2: 160 and 80+80 MHz support
* 3: (reserved)
The check must therefore not be done bitwise but instead it must checked
whether the capabilities announced by the driver are at least the ones
requested by the user.
Fixes: c781eb8428 ("hostapd: Verify VHT capabilities are supported by driver")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
X509_ALGOR_get0() was modified to use const ** pointer as the first
argument in OpenSSL 1.1.0, so need to use different type here to avoid
compilation issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add OCE IE in Beacon, Probe Response, and (Re)Association Response
frames if OCE is enabled in the configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This request ID was wrongly referred from the REQUEST_ID in
enum qca_wlan_vendor_attr_gscan_config_params which is mapped to
QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM in PNO Config.
Hence define a different attribute to represent the request ID
for PNO Config.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
dpp.h file requires openssl in order to compile, which breaks
compilation on systems without it.
Move DPP_OUI_TYPE to ieee802_11_defs.h and don't include dpp.h when
not really needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The attribute is QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE, not
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The DPP Configurator can use this new command to generate its own signed
connector for the network that it manages.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
