Define a QCA vendor command to configure SAR Power limits
There is a regulatory requirement for Specific Absorption Rate (SAR) whereby the device transmit power is reduced when it is determined that the device is in close proximity to the body. Implement a vendor command interface to allow a userspace entity to dynamically control the SAR power limits. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit is contained in:
Jeff Johnson
Jouni Malinen
parent
0f5eb69f85
commit
c79238b6a4
|
|
@ -237,6 +237,12 @@ enum qca_radiotap_vendor_ids {
|
|||
* started with QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN. This command
|
||||
* carries the scan cookie of the corresponding scan request. The scan
|
||||
* cookie is represented by QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE.
|
||||
*
|
||||
* @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS: Set the Specific
|
||||
* Absorption Rate (SAR) power limits. A critical regulation for
|
||||
* FCC compliance, OEMs require methods to set SAR limits on TX
|
||||
* power of WLAN/WWAN. enum qca_vendor_attr_sar_limits
|
||||
* attributes are used with this command.
|
||||
*/
|
||||
enum qca_nl80211_vendor_subcmds {
|
||||
QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0,
|
||||
|
|
@ -345,6 +351,7 @@ enum qca_nl80211_vendor_subcmds {
|
|||
QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS = 143,
|
||||
/* 144 - reserved for QCA */
|
||||
QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN = 145,
|
||||
QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS = 146,
|
||||
};
|
||||
|
||||
|
||||
|
|
@ -2214,4 +2221,122 @@ enum qca_wlan_vendor_tdls_trigger_mode {
|
|||
QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL = 1 << 2,
|
||||
};
|
||||
|
||||
/**
|
||||
* enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any
|
||||
* source of SAR power limits, thereby disabling the SAR power
|
||||
* limit feature.
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0
|
||||
* that is hard-coded in the Board Data File (BDF).
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1
|
||||
* that is hard-coded in the Board Data File (BDF).
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2
|
||||
* that is hard-coded in the Board Data File (BDF).
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3
|
||||
* that is hard-coded in the Board Data File (BDF).
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4
|
||||
* that is hard-coded in the Board Data File (BDF).
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power
|
||||
* limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR.
|
||||
*
|
||||
* This enumerates the valid set of values that may be supplied for
|
||||
* attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of
|
||||
* the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command.
|
||||
*/
|
||||
enum qca_vendor_attr_sar_limits_selections {
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE = 0,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1 = 1,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2 = 2,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3 = 3,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4 = 4,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF5 = 5,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER = 6,
|
||||
};
|
||||
|
||||
/**
|
||||
* enum qca_vendor_attr_sar_limits_spec_modulations -
|
||||
* SAR limits specification modulation
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK -
|
||||
* CCK modulation
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM -
|
||||
* OFDM modulation
|
||||
*
|
||||
* This enumerates the valid set of values that may be supplied for
|
||||
* attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an
|
||||
* instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an
|
||||
* instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor
|
||||
* command.
|
||||
*/
|
||||
enum qca_vendor_attr_sar_limits_spec_modulations {
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK = 0,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM = 1,
|
||||
};
|
||||
|
||||
/**
|
||||
* enum qca_vendor_attr_sar_limits - Attributes for SAR power limits
|
||||
*
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT: Optional (u32) value to
|
||||
* select which SAR power limit table should be used. Valid
|
||||
* values are enumerated in enum
|
||||
* %qca_vendor_attr_sar_limits_selections. The existing SAR
|
||||
* power limit selection is unchanged if this attribute is not
|
||||
* present.
|
||||
*
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value
|
||||
* which specifies the number of SAR power limit specifications
|
||||
* which will follow.
|
||||
*
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power
|
||||
* limit specifications. The number of specifications is
|
||||
* specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each
|
||||
* specification contains a set of
|
||||
* QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A
|
||||
* specification is uniquely identified by the attributes
|
||||
* %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND,
|
||||
* %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and
|
||||
* %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always
|
||||
* contains as a payload the attribute
|
||||
* %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT.
|
||||
*
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to
|
||||
* indicate for which band this specification applies. Valid
|
||||
* values are enumerated in enum %nl80211_band (although not all
|
||||
* bands may be supported by a given device). If the attribute is
|
||||
* not supplied then the specification will be applied to all
|
||||
* supported bands.
|
||||
*
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value
|
||||
* to indicate for which antenna chain this specification
|
||||
* applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the
|
||||
* attribute is not supplied then the specification will be
|
||||
* applied to all chains.
|
||||
*
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32)
|
||||
* value to indicate for which modulation scheme this
|
||||
* specification applies. Valid values are enumerated in enum
|
||||
* %qca_vendor_attr_sar_limits_spec_modulations. If the attribute
|
||||
* is not supplied then the specification will be applied to all
|
||||
* modulation schemes.
|
||||
*
|
||||
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32)
|
||||
* value to specify the actual power limit value in units of 0.5
|
||||
* dBm (i.e., a value of 11 represents 5.5 dBm).
|
||||
*
|
||||
* These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS.
|
||||
*/
|
||||
enum qca_vendor_attr_sar_limits {
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID = 0,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE = 1,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS = 2,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC = 3,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND = 4,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN = 5,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION = 6,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT = 7,
|
||||
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST,
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX =
|
||||
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST - 1
|
||||
};
|
||||
|
||||
#endif /* QCA_VENDOR_H */
|
||||
|
|
|
|||
Loading…
Reference in a new issue