It was possible that nl80211_get_hw_feature_data() function would return
NULL when num_modes is not set to zero. This might result in a later crash
when accessing hw.modes. This may be reproduced with hwsim oom tests, for
example, dbus_connect_oom.
Fix that by zeroing num_modes if NULL is returned.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This fixes the netlink attribute identifier for the scan flags when
using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd control interface event "BEACON-RESP-RX <STA address>
<dialog token> <report mode> <beacon report>" is now used to report
received beacon reports as a reponse to the REQ_BEACON operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new BEACON-REQ-TX-STATUS control interface event is now used to
report whether a beacon request (from REQ_BEACON command) was delivered
successfully. This event has the following parameters: <STA address>
<dialog token> <ack=0/1>.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new control interface command "REQ_BEACON <STA addr>
[req_mode=<mode>] <beacon request>" can now be used to request hostapd
to transmit a measurement request to request a beacon report from an
associated STA. This command returns the assigned dialog token (1-255)
or FAIL on failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
The loop to add hash values was supposed to be limited to at most 10000
values, but the count variable was not being decremented in the loop.
Fix this by decrementing counting for each iteration. This fixes
ANQP-element format in the unlikely case of there being more than 10000
configuration realms.
Signed-off-by: Jouni Malinen <j@w1.fi>
This conversion will be done several times in the code, so add a helper
function that does this conversion.
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
Add a function to get operating class definition (including bandwidth,
channel numbers, etc.) from the operating class number and country.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add helper function that converts non-global operating classes to global
operating classes according to IEEE Std 802.11-2016, Annex E.
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
Add support for:
1. Setting scan dwell time
2. Parsing scan start TSF and beacon received TSF reported
by the driver
3. Setting driver capabilities for the above
These capabilities are needed for Beacon Report radio measurement.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add the following parameters to scan request:
1. Dwell time on each channel.
2. Whether the specified dwell time is mandatory.
In addition, add to scan results info the time that the scan actually
started, and to each scan result the time the beacon/probe was received,
both in terms of TSF of the BSS that the interface that requested the
scan is connected to (if available).
Add flags to indicate whether the driver supports dwell time
configuration and scan information reporting.
This scan configuration and information is required to support beacon
report radio measurement.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The address of msg.device_name array is obviously always true, and some
compilers even warn about it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The actual BSS configuration parameter can be updated with the SET
control interface command, so there is no need to maintain a separate
per-BSS parameter and a separate control interface handling for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the hostapd ft_over_ds parameter was used to only advertise
whether FT-over-DS is enabled in MDE and leave it to the stations to
follow that advertisement. This commit extends this to explicitly reject
(silently drop) FT Action frames if a station does not follow the
advertised capabilities.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible to hit the previously used maximum of 100 active session
in some hwsim test case sequences like this one: eap_proto_pwd_errors
eap_proto_ikev2_errors eap_proto_sim_errors. This happened due to the
large number of RADIUS authentication iterations in short period of
time, i.e., within the 10 second timeout for expiring completed
sessions.
Increase RADIUS_MAX_SESSION from 100 to 1000 and also reduce the timeout
on expiring completed sessions from 10 to 5 seconds.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, this was noted in error log, but the invalid value was
stored in the configuration without rejecting it.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible to try to do driver operations before the driver
interface had been initialized when processing a SIGHUP signal. This
would result in NULL pointer dereference. Fix this by skipping the steps
when SIGHUP is issued before the interface is enabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function is already checking the fname argument against NULL, so
use that check on its own instead of duplicating the check in the only
caller.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a new wpa_supplicant network profile parameter
mka_priority=0..255 to set the priority of the MKA Actor.
Signed-off-by: Badrish Adiga H R <badrish.adigahr@gmail.com>
wpa_cipher_to_alg() returns enumerated values from enum wpa_alg and all
uses of the return value treat it as enum wpa_alg (by either assigning
it to a variable of type enum wpa_alg or passing to a function that
expects enum wpa_alg).
This commit updates the return value to match the expected usage
(enum wpa_alg) rather than int. This ensures the return value is
of the proper type and eliminates the following compiler warnings:
ARM RVCT (2.2):
'Warning: #188-D: enumerated type mixed with another type'
Signed-off-by: Joel Cunningham <joel.cunningham@me.com>
Number of deployed use cases assume the default OpenSSL behavior of auto
chaining the local certificate is in use. BoringSSL removed this
functionality by default, so we need to restore it here to avoid
breaking existing use cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This simplifies the implementation since the SSL_clear_options() and
SSL_CTX_clear_options() are available in all supported versions of
OpenSSL. These were previously needed with older (now obsolete) versions
of OpenSSL, but the ifdefs were missed when removing the more explicit
version macro based backwards compatibility sections.
In practice, this reverts commit
d53d2596e4.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The full SD Response frame is not going to be followed by another Action
frame from the peer, so remove the 200 ms wait time from the offchannel
TX command in that case. This avoids leaving a 200 ms lock on the radio
to remain on the channel unnecessarily.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is apparently possible for the NL80211_CMD_UNEXPECTED_4ADDR_FRAME
event to be delivered to hostapd before the NL80211_CMD_FRAME_TX_STATUS
event for (Re)Association Response frame. This resulted in the 4-address
WDS mode not getting enabled for a STA. This could occur in particular
when operating under heavy load and the STA is reconnecting to the same
AP in a sequence where Deauthentication frame is followed immediately by
Authentication frame and the driver event processing gets delayed due to
removal of the previous netdev taking time in the middle of this
sequence.
Fix this by recording a pending item for 4-address WDS enabling if the
NL80211_CMD_UNEXPECTED_4ADDR_FRAME event would have been dropped due to
incompleted association and then process this pending item if the TX
status for the (Re)Association Response frame is received and it shows
that the frame was acknowledged.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This registers a new callback to indicate change in SIM state. This
helps to do some clean up (more specifically pmksa_flush) based on the
state change of the SIM. Without this, the reconnection using the cached
PMKSA could happen though the SIM is changed.
Currently eap_proxy_sim_state corresponds to only SIM_STATE_ERROR. This
can be further extended.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The eapol_cb structure was made const and that change resulted in a
compilation warning/error if CONFIG_EAP_PROXY=<name> is enabled in the
wpa_supplicant build configuration. Fix this by updating the function
prototype to match the change.
Note: This results in a change needed to external eap_proxy_*.c
implementations to match the change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit c93b7e1888 ('RSN: Check result of
EAPOL-Key frame send request') forgot to update two PeerKey users of
EAPOL-Key TX functions. That resulted in STK handshake failing since
message 2/4 and 4/4 TX calls were assumed to have failed when the return
value was changed from 0 to a positive value for success case. This
resulted in not updating nonce information properly and hitting
following error when processing STK 4-way handshake message 3/4:
RSN: INonce from message 1 of STK 4-Way Handshake differs from 3 of STK
4-Way Handshake - drop packet (src=<addr>)
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 6d014ffc6e ('Make struct
wpa_eapol_key easier to use with variable length MIC') forgot to update
number of EAPOL-Key processing steps for SMK and STK exchanges and broke
PeerKey. Fix this by updating the Key Data field pointers to match the
new style with variable length Key MIC field.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter fils_realm=<realm> can now be
used to configure one or more FILS realms to advertise for ERP domains
when using FILS. This replaces the use of erp_domain=<domain> parameter
for the FILS use case.
Signed-off-by: Jouni Malinen <j@w1.fi>
P802.11ai/D7.0 changed from CRC32 to SHA256 as the hash algorithm for
the FILS realm name. Update the implementation to match that change.
Signed-off-by: Jouni Malinen <j@w1.fi>
This updates definitions for Status Codes, Reason Codes,
Information Element IDs, Action frame categories, Public Action
codes, Protected Dual of Public Action codes, Advertisement
Protocol ID, and ANQP info IDs based on IEEE Std 802.11-2016.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes both the Probe Response and Beacon frame IEs available to
upper layers if scan results include both IE sets. When the BSS command
mask includes WPA_BSS_MASK_BEACON_IE, a new beacon_ie=<hexdump> entry
will be included in output if the BSS entry has two separate sets of IEs
(ie=<hexdump> showing the Probe Response frame contents and
beacon_ie=<hexdump> the Beacon rame contents).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the secondary channel was not found at all, no debug print was shown
to indicate that the channel was rejected due to that problem. Print a
clearer message indicating which channel was behind the reason to reject
channel configuration as unsuitable for AP mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant control interface commands PMKSA_GET and
PMKSA_ADD that can be used to store PMKSA cache entries in an external
persistent storage when terminating a wpa_supplicant process and then
restore those entries when starting a new process. The previously added
PMKSA-CACHE-ADDED/REMOVED events can be used to help in synchronizing
the external storage with the memory-only volatile storage within
wpa_supplicant.
"PMKSA_GET <network_id>" fetches all stored PMKSA cache entries bound to
a specific network profile. The network_id of the current profile is
available with the STATUS command (id=<network_id). In addition, the
network_id is included in the PMKSA-CACHE-ADDED/REMOVED events. The
output of the PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration in seconds>
<akmp> <opportunistic>
For example:
02:00:00:00:03:00 113b8b5dc8eda16594e8274df4caa3d4 355e98681d09e0b69d3a342f96998aa765d10c4459ac592459b5efc6b563eff6 30240 43200 1 0
02:00:00:00:04:00 bbdac8607aaaac28e16aacc9152ffe23 e3dd6adc390e685985e5f40e6fe72df846a0acadc59ba15c208d9cb41732a663 30240 43200 1 0
The PMKSA_GET command uses the following format:
<network_id> <BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration
in seconds> <akmp> <opportunistic>
(i.e., "PMKSA_ADD <network_id> " prefix followed by a line of PMKSA_GET
output data; however, the reauth_time and expiration values need to be
updated by decrementing them by number of seconds between the PMKSA_GET
and PMKSA_ADD commands)
For example:
PMKSA_ADD 0 02:00:00:00:03:00 113b8b5dc8eda16594e8274df4caa3d4 355e98681d09e0b69d3a342f96998aa765d10c4459ac592459b5efc6b563eff6 30140 43100 1 0
PMKSA_ADD 0 02:00:00:00:04:00 bbdac8607aaaac28e16aacc9152ffe23 e3dd6adc390e685985e5f40e6fe72df846a0acadc59ba15c208d9cb41732a663 30140 43100 1 0
This functionality is disabled be default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option. It should be
noted that this allows any process that has access to the wpa_supplicant
control interface to use PMKSA_ADD command to fetch keying material
(PMK), so this is for environments in which the control interface access
is restricted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These allow external program to monitor PMKSA cache updates in
preparation to enable external persistent storage of PMKSA cache.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd didn't send "TERMINATING" event when stopped by
SIGTERM. Android handles this event to stop monitor thread.
This commit adds "TERMINATING" event same as with wpa_supplicant.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
This allows the vendor scan to be optimized when a response is needed
only from a single, known BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit documents the QCA vendor commands 61-73 and the
corresponding definitions of the attributes. This set of commands were
previously reserved for QCA without documentation here.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These thresholds values indicate how many Beacon frames can be missed
before before disconnecting from the AP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit c79238b6a4 ('Define a QCA vendor
command to configure SAR Power limits') had a mismatch between the enum
qca_vendor_attr_sar_limits_selections documentations and actual values.
The BDF SAR profiles are 0-based, so rename the enum values and reorder
the values keep the actual values more convenient. While this changes
values over the interface, this is justifiable since the new command was
introduced only recently and it had not been released in any driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is to handle the case when peer changes device name and same needs
to be updated to upper layers by P2P-DEVICE-FOUND event. It is similar
to the case when a peer changes wfd_subelems and P2P-DEVICE-FOUND event
goes to upper layers.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
When a peer device stops sending wfd_subelems, wpa_supplicant should
remove dev->info.wfd_subelems from peer's properties. Previously,
wpa_supplicant left the previously learned dev->info.wfd_subelems in
place whenever the new message did not include wfd_subelems.
In addition to fixing the clearing of the old wfd_subelems, this
resolves another issue. As "wfd_changed" variable becomes true even when
peer stops sending wfd_subelems and dev->info.wfd_subelems has an old
value, a new P2P-DEVICE-FOUND event notification was sent again and
again to upper layers whenever a new discovery response was received
from the peer that previously advertised WFD subelements.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Previously, this flag was cleared only in case of failed GO Negotiation.
That could leave the flag set for a peer and if a new group formation
was performed with the same peer before the entry expired, there was
increased risk of getting stuck in a state where neither peer replied to
a GO Negotiation Request frame if a GO Negotiation Response frame with
Status 1 was dropped.
The error sequence could happen in the go_neg_with_bss_connected test
case when timing was suitable to make the second GO negotiation drop a
pending TX Action frame if the GO Negotiation Response with Status 1 was
scheduled for transmission during a P2P scan and P2P_CONNECT was issued
before that scan got aborted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is a regulatory requirement for Specific Absorption Rate (SAR)
whereby the device transmit power is reduced when it is determined that
the device is in close proximity to the body. Implement a vendor command
interface to allow a userspace entity to dynamically control the SAR
power limits.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, os_sleep() was used to block the hostapd (or wpa_supplicant
AP/P2P GO mode) processing between sending out EAP-Failure and
disconnecting the STA. This is not ideal for couple of reasons: it
blocks all other parallel operations in the process and it leaves a
window during which the station might deauthenticate and the AP would
have no option for reacting to that before forcing out its own
Deauthentication frame which could go out after the STA has already
started new connection attempt.
Improve this design by scheduling an eloop timeout of 10 ms instead of
the os_sleep() call and perform the delayed operations from the eloop
callback function. This eloop timeout is cancelled if the STA
disconnects or initiates a new connection attempt before the 10 ms time
is reached. This gets rid of the confusing extra Deauthentication frame
in cases where the STA reacts to EAP-Failure by an immediate
deauthentication.
Signed-off-by: Jouni Malinen <j@w1.fi>
On a connect nl80211 event, wpa_supplicant uses
wpa_driver_nl80211_get_ssid() to fetch the current associated SSID to
compare to existing configurations. However,
wpa_driver_nl80211_get_ssid() uses drv->ssid, which is a cached value.
It is set when we explicitly initial a connect request using
wpa_supplicant. If the association was initiated outside of
wpa_supplicant, we need another way to populate drv->ssid. This commit
sets drv->ssid based on cfg80211 BSS information on connect/associate
nl80211 events.
Signed-off-by: Ningyuan Wang <nywang@google.com>
Commit adcd7c4b0b ('nl80211: Support
vendor scan together with normal scan') made the drv->scan_state updates
for NL80211_CMD_NEW_SCAN_RESULTS and NL80211_CMD_SCAN_ABORTED
conditional on drv->last_scan_cmd being NL80211_CMD_TRIGGER_SCAN. This
missed the part about the possibility of last_scan_cmd == 0 and an
externally started cfg80211 scan is ending. This could leave
drv->scan_state into SCAN_STARTED state even after the scan was
completed. Consequently, hwsim test cases could get stuck in reset()
handler waiting for scan to terminate.
Fix this by updating drv->scan_state also in drv->last_scan_cmd == 0
case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for nl80211 NL80211_CMD_SET_MULTICAST_TO_UNICAST
command.
By setting the new hostapd configuration option multicast_to_unicast=1,
hostapd configures this AP to perform multicast to unicast conversion.
When enabled, all multicast packets with ethertype ARP, IPv4, or IPv6
(possibly within an 802.1Q header) will be sent out to each station once
with the destination (multicast) MAC address replaced by the station's
MAC address. Note that this may break certain expectations of the
receiver, e.g., the ability to drop unicast IP packets encapsulated in
multicast L2 frames, or the ability to not send destination unreachable
messages in such cases.
This also does not implement Directed Multicast Service (DMS).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
We should unconditionally remove inactivity timers for wired network
cases. This commit checks for this after a new station association:
hapd->iface->drv_flags & WPA_DRIVER_FLAGS_WIRED
and then cancels the timeout and does not register a new one.
It prints out a debug message like this:
1476740180.276286: IEEE 802.1X: 00:02:00:00:00:07 CTRL_DIR entering
state FORCE_BOTH
1476740180.276295: hostapd_new_assoc_sta: canceled wired ap_handle_timer
timeout for 00:02:00:00:00:07
This was tested on a debian jessie amd64 system with a configured 120
second inactivity timer and the session did not timeout.
Signed-off-by: Sam Tannous <stannous@cumulusnetworks.com>
Do not use the generic bss_info_handler() design to fetch all scan
results into temporary memory buffer. Instead, use a separate BSS info
handler that fetches the requested information without fully parsing the
BSS entries and without allocating any memory for collecting all the
results.
This is also simplifying bss_info_handler() and nl80211_parse_bss_info()
design by getting rid of the special case that was used only for
nl80211_get_assoc_freq() and not normal scan result fetching.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of fetching all scan results to a temporary buffer, debug print
scan result dump directly from the message handler function one BSS at a
time.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a single scan result to be parsed at a time. This is a step
towards optimizing scan result fetching without having to allocate
memory for all entries at the same time.
Signed-off-by: Jouni Malinen <j@w1.fi>
The way the removal of duplicated (one per frequency) BSS entries in the
cfg80211 scan results were removed in driver_nl80211_scan.c
bss_info_handler() depended on having the full scan results available to
allow iteration through the other entries. This is problematic for the
goal of being able to optimize memory allocations for scan result
fetching in a manner that would not build the full result buffer in
memory.
Move this duplicate removal into bss.c since it has sufficient
information available for doing the same determination of which one of
two BSS entries is more current.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_priv did not yet support Beacon frame IEs (res->beacon_ie_len) which
resulted in invalid scan data being accepted in driver_privsep.c. Add
support for res->beacon_ie_len and also fix the validation step to take
this new variable length field into account.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a single scan result to be checked at a time. This is a step
towards optimizing scan result fetching without having to allocate
memory for all entries at the same time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This untangles the NL80211_CMD_GET_SURVEY handler loop from
NL80211_CMD_GET_SCAN processing so that the per-channel noise
information can be fetched with a common function to a local data
structure that can then be easily used to update individual scan results
(a single BSS) instead of having to go through a full set of scan
results. This is a step towards optimizing scan result fetching without
having to allocate memory for all entries at the same time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Data connection was lost if a station reassociated without the STA entry
being cleaned up on the AP side. Fix this by moving reconfiguration of
the STA WDS parameters in association response callback to happen only
after the STA flags have been updated to associated stated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are used only within driver_wired_common.c now at the end of the
refactoring changes, so there is no need to make these helper functions
available outside driver_wired_common.c.
Signed-off-by: Jouni Malinen <j@w1.fi>
This uses libnl3 to communicate with the macsec module available on
Linux. A recent enough version of libnl is needed for the macsec.h file
(which is not yet available in a formal libnl release at the time of
this commit).
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Refactor the common parts of wired drivers code into a shared file, so
that they can be reused by other drivers. The macsec_qca driver already
contains a lot of code duplication from the wired driver, and the
macsec_linux driver would do the same. A structure to hold data common
to all wired drivers is added and used in all these drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This commit enhances the abort scan implementation to also abort the
vendor scan, if one was used to trigger the scan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN command can be used to
abort an ongoing scan that was started with
QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes a regression from commit
bb598c3bdd ('AP: Add support for full
station state'). That commit added code to remove and re-add the kernel
STA entry when processing Authentication frames with a driver that
advertises support for full AP client state. That resulted in bypassing
PMF protections for unprotected Authentication frames with such drivers
since the TK was lost in this operation.
It is simplest to skip the STA entry clearing in this type of case
completely to leave the TK in place and to process the new
authentication exchange otherwise normally. This matches the behavior
used with the drivers that do not implement full AP client state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11-2012, 12.4.2 states that if an MDE is present in an
(Re)Association Request frame but the RSNE uses a non-FT AKM suite, the
AP shall reject the association using status code 43 ("Invalid AKMP").
wpa_validate_wpa_ie() now explicitly checks for this condition to meet
this requirement instead of simply ignoring the MDE based on non-FT AKM.
Signed-off-by: Will Glynn <will@willglynn.com>
If the driver advertises support for setting Beacon frame data rate,
allow the user to configure this rate as part of starting the AP. Only
one Beacon frame TX rate is allowed.
Drivers advertising such support should set corresponding flag via the
NL80211_ATTR_EXT_FEATURES attribute.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow configuration of Beacon frame TX rate from hostapd.conf with
"beacon_rate=xx" option. The following format is used to set
legacy/HT/VHT beacon rates:
Legacy (CCK/OFDM rates):
beacon_rate=<legacy rate in 100 kbps>
HT:
beacon_rate=ht:<HT MCS>
VHT:
beacon_rate=vht:<VHT MCS>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, wpa_supplicant only supported hardcoded port == 1 in the
SCI, but users may want to choose a different port.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
So that the user can turn encryption on (MACsec provides
confidentiality+integrity) or off (MACsec provides integrity only). This
commit adds the configuration parameter while the actual behavior change
to disable encryption in the driver is handled in the following commit.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
The first peer may take a long time to come up. In PSK mode we are
basically in a p2p system, and we cannot know when a peer will join the
key exchange. Wait indefinitely, and let the administrator decide if
they want to abort.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This commit fixes the nl80211 driver call get_inact_sec() to return -1
when STA inactivity time retrieval fails in i802_read_sta_data().
This was intended to be handled by initalizing the inactive_msec member
to -1 but i802_read_sta_data() assumes the data parameter is
uninitialized and memsets the entire structure, neutralizing the attempt
to distinguish between no value (-1) and a time value of 0.
This is fixed by now requiring i802_read_sta_data() callers to
initialize the data structure first (allowing get_inact_sec() to use
-1). This is a safe change because it does not change any driver API
behavior and only affects one other static function in driver_nl80211.c
Signed-off-by: Joel Cunningham <joel.cunningham@me.com>
In commit a25e4efc9e ('mka: Add driver op
to get macsec capabilities') I added some code to check the driver's
capabilities. This commit has two problems:
- wrong enum type set in kay->macsec_confidentiality
- ignores that drivers could report MACSEC_CAP_NOT_IMPLEMENTED, in
which case the MKA would claim that MACsec is supported.
Fix this by interpreting MACSEC_CAP_NOT_IMPLEMENTED in the same way as a
DO_NOT_SECURE policy, and set the correct value in
kay->macsec_confidentiality.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This extends the anqp_elem configuration parameter support for new Info
IDs (270 (TDLS Capability) was previously missed from the list of
defined values, 280 has already been assigned in REVmc/D8.0; 281..299
are yet to be assigned). No additional source code changes are needed to
allow hostapd to advertise support for these if the ANQP-element value
is set with the anqp_elem parameter.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, CONFIG_IEEE80211R enabled build that supports FT for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode FT is required and there is no need for AP mode FT.
Add support to differentiate between station mode FT and AP mode FT in
wpa_supplicant builds by adding CONFIG_IEEE80211R_AP that should be used
when AP mode FT support is required in addition to station mode FT. This
allows binary size to be reduced for builds that require only the
station side FT functionality.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The Channel Center Frequency Segment subfields use the channel index
instead of frequency in MHz.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
The return value from this function may be used in an outgoing message,
so use a valid status code instead of -1.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add a configuration option in hostapd.conf and in neighbor report that
sets an AP as stationary. To enable this option on the current AP set
the config option stationary_ap to 1. To set a neighbor entry to be
marked as stationary add the word stat to the SET_NEIGHBOR command. This
option tells hostapd to send LCI data even if it is older than requested
by max age subelement in RRM request.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
It is possible that a LCI or location civic configuration buffer
is valid but contains no data. In such a case do not add the LCI
and location civic information to the entry in the neighbor
data base.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
struct data_key already had a 'user' field for reference counting, but
it was basically unused.
Add an ieee802_1x_kay_use_data_key() function to take a reference on a
key, and use ieee802_1x_kay_deinit_data_key() to release the reference.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Document some data structures from IEEE Std 802.1X-2010, and add the
(not used yet) struct ieee802_1x_mka_dist_cak_body.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This is specific to the macsec_qca driver. The core implementation
shouldn't care about this, and only deal with the complete secure
channel, and pass this down to the driver.
Drivers that have such limitations should take care of these in their
->create functions and throw an error.
Since the core MKA no longer saves the channel number, the macsec_qca
driver must be able to recover it. Add a map (which is just an array
since it's quite short) to match SCIs to channel numbers, and lookup
functions that will be called in every place where functions would get
the channel from the core code. Getting an available channel should be
part of channel creation, instead of being a preparation step.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This has already been done for WEP, but there's same constraint for not
allowing VTH rates in case of TKIP.
Signed-off-by: Filip Matusiak <filip.matusiak@tieto.com>
Receiving a provision discovery request for an ASP service that
has auto accept set to false should result in a provision discovery
response with the status field set to "currently unavailable".
Having stale P2PS provision data, results in sending a response with
the status set to success because it is mistakenly referred to as the
follow-on provision discovery request.
Fix that by clearing stale P2PS provision data in the following cases:
1. When provision discovery is complete
2. When ASP services are flushed (in which case old ASP provisioning
is no longer valid).
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
drv->in_listen should be cleared whenever the state timeout is cleared,
if they were set together. If the flag is not cleared, the
p2p_listen_end() called during cancel-remain-on-channel will not restart
the search, relying on the state timeout function to do it. Use the
p2p_stop_listen_for_freq() function to clear the listen state properly.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Otherwise, if a P2PS provision is incomplete before the flush, it can
cause incorrect provision responses to be sent out.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Add signal level information to the station tracking information. Also
make it available via the "TRACK_STA_LIST" control command.
Signed-off-by: Kevin Mahoney <k.mahoney@cablelabs.com>
ext_capab/ext_capab_len do not include ID and Length so no extra +2
offset should be used. This fixes a regression from commit
faf427645a ('TDLS: Use proper IE parsing
routine for non-EAPOL-Key cases') that replaced the IE parser without
noticing the difference in the pointer offset.
Signed-off-by: Flavia Vanetti <flavia.vanetti@ceva-dsp.com>
When channel switch happens, driver wrapper's internal channel
information needs to be updated so that the new frequency will be used
in operations using drv->assoc_freq. Previously, only bss->freq was
updated and the new frequency was also indicated in the EVENT_CH_SWITCH
event. This could potentially leave out couple of cases that use
drv->assoc_freq at least as a fallback mechanism for getting the current
operating frequency.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds a control interface command to configure the TDLS
trigger mode to the host driver. This TDLS mode is configured through
the "SET tdls_trigger_control" control interface command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These attributes were previously maintained elsewhere. This commit moves
them to follow the standard assignment process through the qca-vendor.h
file in hostap.git.
Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
Add a new vendor attribute config to set the reorder blocksize and
timeout in 4 ACs, and then report the frame aggregation failure
statistics in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command. In addition,
fix the spelling of the enum value for this subcommand.
Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
This sends the FILS KEK and AAD context (nonces) to the driver with the
NL80211_CMD_ASSOCIATE messages when using FILS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_remove_ptk() call to wpa_auth_set_key() more consistent
with all the other calls that verify the return value to keep static
analyzers happier.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"GET_CAPABILITY fils" used to return "FILS" based on wpa_supplicant
configuration. This can be made more useful by checking both for
wpa_supplicant and driver support for FILS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Decrypt the AES-SIV protected elements and verify Key-Auth. Parse and
configure keys to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the FILS KEK and AAD data (nonces) to be configured to the
driver for association so that the driver can encrypt the
(Re)Association Request frame and decrypt the (Re)Association Response
frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements processing of FILS Authentication frame for FILS shared
key authentication with ERP and PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
ieee802_1x_encapsulate_radius() and ieee802_1x_alloc_eapol_sm() need to
be called from FILS processing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a PMKSA cache entry for the target AP is available, try to use FILS
with PMKSA caching.
If an ERP key for the target AP is available, try to use FILS with
EAP-Initiate/Re-auth added as Wrapper Data element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This needs to be callable through the EAPOL supplicant wrappers to allow
FILS implementation to use ERP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements Key-Auth derivation for (Re)Association Request frames
(see P802.11ai/D11.0 12.12.2.6.2) and (Re)Association Response frames
(see P802.11ai/D11.0 12.12.2.6.3).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is the PTKSA key derivation used as part of the FILS authentication
exchange. See P802.11ai/D11.0 12.12.2.5.3.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it cleaner for the FILS implementation to use the same design
for setting Authentication frame elements as was already done with SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add operations to allow low level control over RF sectors in QCA DMG
(11ad) chipsets. Operations include getting/setting the configuration of
a specific sector, as well as getting/setting the selected sector which
the HW uses to communicate with a specific station.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
That function does not need the full EAP header -- it only needs to know
which EAP identifier to use in the message. Make this usable for cases
where the previous EAP message may not exist (FILS).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This changes 4-way handshake authenticator processing to decrypt the
EAPOL-Key frames using an AEAD cipher (AES-SIV with FILS AKMs) before
processing the Key Data field. This replaces Key MIC validation for the
cases where AEAD cipher is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This changes 4-way handshake authenticator processing to decrypt the
EAPOL-Key frames using an AEAD cipher (AES-SIV with FILS AKMs) before
processing the Key Data field. This replaces Key MIC validation for the
cases where AEAD cipher is used. This needs to move the EAPOL-Key msg
2/4 RSN element processing to happen only after the PTK has been derived
and validated. That is done for all AKMs to avoid extra complexity with
having to maintain two code paths for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This modifies wpa_eapol_key_send() to use AEAD cipher (AES-SIV for FILS
AKMs) to provide both integrity protection for the EAPOL-Key frame and
encryption for the Key Data field. It should be noted that this starts
encrypting the Key Data field in EAPOL-Key message 2/4 while it remains
unencrypted (but integrity protected) in non-FILS cases. Similarly, the
empty Key Data field in EAPOL-Key message 4/4 gets encrypted for AEAD
cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This will be needed to be able to implement AEAD cipher support from
FILS that will need to use KEK to protect the frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Suite B 192-bit addition from IEEE Std 802.11ac-2013 replaced the
previous fixed length Key MIC field with a variable length field. That
change was addressed with an addition of a new struct defined for the
second MIC length. This is not really scalable and with FILS coming up
with a zero-length MIC case for AEAD, a more thorough change to support
variable length MIC is needed.
Remove the Key MIC and Key Data Length fields from the struct
wpa_eapol_key and find their location based on the MIC length
information (which is determined by the AKMP). This change allows the
separate struct wpa_eapol_key_192 to be removed since struct
wpa_eapol_key will now include only the fixed length fields that are
shared with all EAPOL-Key cases in IEEE Std 802.11.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Calculate the hashed realm from hostapd erp_domain configuration
parameter and add this to the FILS Indication element when ERP is
enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If FILS is enabled, indicate that in Beacon, Probe Response, and
(Re)Association Response frames in the Extended Capabilities element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds CONFIG_FILS=y build configuration option and new key
management options for FILS authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds definitions for new information elements from P802.11ai/D11.0
and parsing of these IEs.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previous implementation was hardcoded to use 128-bit AES key
(AEAD_AES_SIV_CMAC_256). Extend this by allowing AEAD_AES_SIV_CMAC_384
and AEAD_AES_SIV_CMAC_512 with 192-bit and 256-bit AES keys.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the CRC-32 routine to be shared for other purposes in
addition to the WEP/TKIP/FCS within wlantest.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Station should be able to connect initially without ft_pmk_cache filled,
so the target AP has the PSK available and thus the same information as
the origin AP. Therefore neither caching nor communication between the
APs with respect to PMK-R0 or PMK-R1 or VLANs is required if the target
AP derives the required PMKs locally.
This patch introduces the generation of the required PMKs locally for
FT-PSK. Additionally, PMK-R0 is not stored (and thus pushed) for FT-PSK.
So for FT-PSK networks, no configuration of inter-AP communication is
needed anymore when using ft_psk_generate_local=1 configuration. The
default behavior (ft_psk_generate_local=0) remains to use the pull/push
protocol.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This also implements the macsec_get_capability for the macsec_qca
driver to maintain the existing behavior.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
RFC 5931 Section 2.8.5.1 does not list the Prep field as something that
the server validates to match the Request. However, the supplicant side
has to use the same pre-processing mechanism for the password for the
authentication to work, so we may as well as enforce this field to match
the requested value now that wpa_supplicant implementation is fixed to
copy the value from the request.
Signed-off-by: Jouni Malinen <j@w1.fi>
Fix the pre-processing field in the response when EAP_PWD_PREP_MS is
being used. This fixes interoperability with EAP-pwd servers that
validate the Prep field in EAP-pwd-ID/Response when the RFC2759
(PasswordHashHash) pre-processing is used.
Signed-off-by: Brian Candler <B.Candler@pobox.com>
Clean up the driver interface by passing pointers to struct receive_sc
down the stack to the {create,delete}_recevie_sc() ops, instead of
passing the individual properties of the SC.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Clean up the driver interface by passing pointers to struct transmit_sc
down the stack to the {create,delete}_transmit_sc() ops, instead of
passing the individual arguments.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This basically just follows commit
587b0457e0 ('LibreSSL: Fix build with
LibreSSL') with the same pattern, which was missed here.
Signed-off-by: Julian Ospald <hasufell@hasufell.de>
Due to a missing guard for old OpenSSL code, SSL_library_init() was not
called, which is required for LibreSSL. Likewise for cleanup.
Signed-off-by: Christian Neukirchen <chneukirchen@gmail.com>
Add LibreSSL check to old OpenSSL #ifdef guard as DH_{get0,set0}_key()
is not implemented in LibreSSL.
Signed-off-by: Christian Neukirchen <chneukirchen@gmail.com>
Add attributes for specifing the frequency where FTM/AOA measurement is
done over the air. This allows the user space framework to maintain its
own cache of peers without depending on the kernel scan results cache,
or perform scans less often (since entries in the kernel scan results
cache expire quickly). The change is backward compatible. If the
frequency attribute is not specified, the kernel scan results cache will
be queried, like done today.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Clean up the driver interface by passing pointers to struct receive_sa
down the stack to the {create,enable,disable}_receive_sa() ops, instead
of passing the individual properties of the SA.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Clean up the driver interface by passing pointers to struct transmit_sa
down the stack to the {create,enable,disable}_transmit_sa ops, instead
of passing the individual properties of the SA.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Clean up the driver interface by passing pointers to structs transmit_sa
and receive_sa down the stack to get_receive_lowest_pn(),
get_transmit_next_pn(), and set_transmit_next_pn() ops, instead of
passing the individual arguments.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
These structs will be passed down to macsec drivers in a coming patch to
make the driver interface cleaner, so they need to be shared between the
core MKA implementation and the drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This makes it easier to copy a subset of definitions without
accidentally getting mismatching values.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends ANQP_GET command to support querying MBO cellular
preference also. The cellular preference can be requested along with
neigbor report by appending mbo:1 to the command arguments.
For example:
ANQP_GET <bssid> 272,mbo:1
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The user space app use QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI cmd to
get the corresponding antenna rssi value for the specific chain. And the
associcated attributes are added to configure the antenna diversity and
related selftest.
Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
The reason detail field was removed from non_pref_chan attr in MBO
v0.0_r25 draft. Don't parse for this element to be compliant with the
latest drafr.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
MBO capable APs can set association disallowed in the Beacon/Probe
Response frames. For testing purposes, the STA needs to be configured to
not ignore the association disallowed set by APs and continue to connect
to such AP like non-MBO enabled STA. Add a QCA vendor attribute for
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION vendor sub command to
configure the driver to ignore association disallowed functionality.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to find bss->drv separately for each parameter, so do
this once at the beginning of the function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add driver parameter command to force capability flag
WPA_DRIVER_FLAGS_BSS_SELECTION even if driver states otherwise. This is
mainly for testing purposes.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Ignore group members for which there is no supported channels
information when calculating common group frequencies.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This command carries 802.11 header and payload along with key (TK) and
PN for encryption/decryption purpose. Firmware/driver encrypts/decrypts
the given data and sends to userspace as a response to the command. User
space component can validate the data received from the driver to unit
test the hardware's encryption engine.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A weakness in the initial client taxonomy mechanism is from storing both
the Probe and Associate in struct sta_info. struct sta_info is created
after a client associates (or starts authentication frame exchange),
which means that any Probe Request frames sent prior to association are
not retained. The Associate Request frame has to be seen, and then
another Probe Request frame after association, before we have a
signature for the client.
Most clients send lots of Probe Request frames (lots and lots and lots
of Probes, actually), but a few do not. ChromeOS is notably sparing in
sending Probe Request frames, it can take a long time before a signature
for a ChromeOS device is available.
Store the most recent Probe Request frame in struct hostapd_sta_info
tracking list. When a struct sta_info is created, move the Probe Request
frame information from struct hostapd_sta_info to struct sta_info.
Signed-off-by: dgentry@google.com (Denton Gentry)
Signed-off-by: denny@geekhold.com (Denton Gentry)
Signed-off-by: rofrankel@google.com (Richard Frankel)
Signed-off-by: richard@frankel.tv (Richard Frankel)
Implement the signature mechanism described in the paper
"Passive Taxonomy of Wifi Clients using MLME Frame Contents"
published by Denton Gentry and Avery Pennarun.
http://research.google.com/pubs/pub45429.htmlhttps://arxiv.org/abs/1608.01725
This involves:
1. Add a CONFIG_TAXONOMY compile option. Enabling taxonomy incurs
a memory overhead of up to several kilobytes per associated
station.
2. If enabled, store the Probe Request and (Re)Associate Request frame in
struct sta_info.
3. Implement code to extract the ID of each Information Element,
plus selected fields and bitmasks from certain IEs, into a
descriptive text string. This is done in a new source file,
src/ap/taxonomy.c.
4. Implement a "signature qq:rr:ss:tt:uu:vv" command
in hostapd_cli to retrieve the signature.
Signatures take the form of a text string. For example, a signature
for the Nexus 5X is:
wifi4|probe:0,1,127,45,191,htcap:01ef,htagg:03,htmcs:0000ffff,vhtcap:338061b2,
vhtrxmcs:030cfffa,vhttxmcs:030cfffa,extcap:00000a0201000040|assoc:0,1,48,45,
221(0050f2,2),191,127,htcap:01ef,htagg:03,htmcs:0000ffff,vhtcap:339071b2,
vhtrxmcs:030cfffa,vhttxmcs:030cfffa,extcap:0000000000000040
Signed-off-by: dgentry@google.com (Denton Gentry)
Signed-off-by: denny@geekhold.com (Denton Gentry)
Signed-off-by: rofrankel@google.com (Richard Frankel)
Signed-off-by: richard@frankel.tv (Richard Frankel)
Previously, struct hostapd_iface sta_seen list head was initialized only
when completing interface setup. This left a window for operation that
could potentially iterate through the list before the list head has been
initialized. While the existing code checked iface->num_sta_seen to
avoid this case, it is much cleaner to initialize the list when struct
hostapd_iface is allocated to avoid any accidental missing of the extra
checks before list iteration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not generate an unused and invalid Request Authenticator (random
value) when constructing Accounting-Request packets. The correct Request
Authenticator is calculated subsequently in radius_msg_finish_acct()
using MD5(msg + shared secret).
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
This reverts commit 647862eb60.
The second check of device_ap_sme looks like duplicated, but it isn't
actually. The trick is nl80211_create_monitor_interface may change that
variable value and the second evaluation may give a different result.
This definitely isn't a very clear code, but that change caused a
regression for drivers that:
1) Don't report NL80211_ATTR_DEVICE_AP_SME
2) Don't support monitor mode
3) Don't support subscribing for PROBE_REQ and/or ACTION frames
like brcmfmac. With such drivers hostapd doesn't start anymore.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The places using drv->use_monitor were already skipping creation of the
monitor interface if drv->device_ap_sme == 0. This means that the
monitor interface operations would not have worked anyway and it is safe
to set drv->use_monitor to zero for all such cases. This fixes an issue
with management frame subscription not happening properly for the case
where the AP SME is in the driver and the driver supports monitor
interfaces (for other purposes).
This commit also removes the check for monitor support and the
previously used workaround that cleared drv->use_monitor in
drv->device_ap_sme == 1 case if monitor interface was not supported
since that condition cannot occur anymore.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Upon receiving FST Setup Request from some peer on some interface,
search is made to see if same peer is connected on other interface with
specific band_id. With multiple peers, bug in
fst_group_does_iface_appear_in_other_mbies() caused wrong peer address
to be returned sometimes.
Fix this with a modified, simplified search algorithm of peer's "other"
connection.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Fix some mistakes in the previous commit for adding QCA vendor commands
for indoor location.
Note: The renamed enum value does not change the ABI, but the addition
of QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID in the beginning of enum
qca_wlan_vendor_attr_ftm_meas does renumber
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_* values. The previous values were
committed yesterday and have not been used in any released code yet, so
this is a justifiable quick fix.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Assign QCA vendor specific commands, attributes, and events for
supporting indoor location features.
These features include:
1. Fine timing measurement (FTM) - allows measurement of distance
between two stations. Based on IEEE P802.11-REVmc/D7.0, 11.24.6 FTM is
performed between two stations: one is an initiator, typically a client
that wants to measure distance to another AP, and one is a responder,
typically an AP which responds to measurement requests from other
clients. The responder can be configured to report its location, either
in absolute coordinates (LCI) or free-form description (LCR).
2. Angle of arrival (AOA) - allows measurement of azimuth and elevation
between two stations.
The above features can be combined to allow a station to get an accurate
indoor location.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Add configuration options that control publishing of fine timing
measurement (FTM) responder and initiator functionality via bits 70, 71
of Extended Capabilities element. Typically, FTM functionality is
controlled by a location framework outside hostapd. When framework is
activated, it will use hostapd to configure the AP to publish the FTM
functionality. See IEEE P802.11-REVmc/D7.0, 9.4.2.27.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Some deployed stations incorrectly consider nsts capability in
(Re)Association Response frame as required capability instead of maximum
capability and if it is greater than station's capability then beamform
will not happen in uplink traffic.
This commit adds support for an optional workaround to use station's
nsts capability in (Re)Association Response frame if the station's nsts
is less than AP by using the use_sta_nsts=1 configuration parameter.
This configuration is introduced in this commit and it is disabled by
default.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Some user space monitor wants to offload link layer statistics to
firmware. A new command QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT and
associcated attributes are added. The monitor will use this new command
to configure monitoring paramters and get link layer statistics.
Attributes added in this change:
1. Parameters for FW to trigger the statistics report
2. Peer STA power state
3. TX failure statistics
Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
Assign cs in ieee802_1x_mka_decode_dist_sak_body and reuse it.
Cleanup of key allocation: ieee802_1x_kay_generate_new_sak() and
ieee802_1x_mka_decode_dist_sak_body() both allocate a struct key_conf,
fill it, and ask ieee802_1x_kay_init_data_key() to allocate and set up a
struct data_key. They also allocate multiple key buffers and copy the
same data around. Stop moving data from buffer to buffer, and just
allocate what we really need.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Instead of copying from kay to a temporary struct, and then from the
struct to the sm, just copy from kay to cp.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This avoids unnecessary typecasting while still being able to compare
the value to CS_TABLE_SIZE without compiler warnings.
Signed-off-by: Jouni Malinen <j@w1.fi>
Share mka deletion implementation in ieee802_1x_participant_timer() for
the cak_life and mka_life expiration cases.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This takes care of priority comparison followed by MAC address
comparison if the priorities are identical.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This is a known constant value (CS_ID_LEN, i.e., the length of the EUI64
identifier) and does not need to be provided separately in these
function calls.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
to_use_sak is a Boolean variable, so there is no need for an if
statement to figure out whether to return TRUE or FALSE.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Use for loop to remove unnecessary goto use and similar cleanup to
simplify the loops in ieee802_1x_mka_i_in_peerlist(),
ieee802_1x_mka_decode_live_peer_body(), and
ieee802_1x_kay_decode_mkpdu().
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Each loop iteration resets body_peer in the beginning, so there is no
need to increment this pointer in the end.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Add ieee802_1x_kay_get_potential_peer() similarly to the previously used
ieee802_1x_kay_get_live_peer() and use these helper functions more
consistently to avoid multiple implementations of peer lookups.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This splits the u32 bitfields into u8 variables and using bitfields only
for the cases where under 8-bit fields are used.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Previously, this was initialized in hostapd_setup_bss() which made it
possible for a REMOVE_NEIGHBOR control interface command to be issued
prior to the list head pointers having been set. That resulted in a NULL
pointer dereference. Fix this by initializing the list head at the time
the data structure gets allocated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Number of hostapd control interface commands (e.g., STATUS-DRIVER) could
result in NULL pointer dereference when issued on not yet enabled BSS.
Fix this by checking that the driver interface has been initialized
before calling the driver_ops function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When the RADIUS client has not yet been fully enabled, MIB command was
segfaulting hostapd.
Signed-off-by: Eduardo Abinader <eduardoabinader@gmail.com>
Accoding to the comment of struct wpa_driver_mesh_bss_params, the
max_peer_links parameter should be under that struct.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Various checks should use is_multicast_ether_addr() instead
of hardcoding the equivalent, change it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, driver_nl80211 sets NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT in
AP mode, to get EAPOL frames out unencrypted when using IEEE 802.1X/WEP.
However, due to the way nl80211/cfg80211 is implemented, this attribute
is ignored by the kernel if NL80211_ATTR_CONTROL_PORT_ETHERTYPE isn't
specified as well. Fix this by including
NL80211_ATTR_CONTROL_PORT_ETHERTYPE set to ETH_P_PAE. This can be done
unconditionally, since the kernel will allow ETH_P_PAE to be set even
when the driver didn't advertise support for arbitrary ethertypes.
Additionally, the params->pairwise_ciphers appear to not be set at
this point, so relax the check and allow them to be zero.
In client mode, this whole thing was missing, so add it. Again, the
pairwise suite can be WPA_CIPHER_NONE, so allow that case as well.
This fixed IEEE 802.1X/WEP EAP reauthentication and rekeying to use
unencrypted EAPOL frames which is the de facto way of implementing this
in wireless networks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To be consistent with OpenSSL 1.1.0, the free functions should
internally check for NULL. EVP_MD_CTX_free also was missing an
EVP_MD_CTX_cleanup, so this leaked a little.
OpenSSL 1.1.0 also has given get_rfc3526_prime_1536 a better namespace
with get_rfc3526_prime_1536 as a compatibility-only name. Use that
instead in 1.1.0.
Signed-off-by: David Benjamin <davidben@google.com>
Do not include a NAS-Port attribute in Access-Request and
Accounting-Request packets where the Association ID (AID) is 0, i.e.,
not yet assigned or known.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Previously, the check for mgmt->bssid matching own address (= BSSID)
ended up rejecting the case where Public Action frames are using
Wildcard BSSID in the Address 3 field. This could result in GAS queries
being dropped. Fix this by allowing both the own address (= AP BSSID)
and Wildcard BSSID in Action frame Address 3 field.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces a new vendor sub command
QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY and the associated
attributes to get Wi-Fi hardware capabilities.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
This can be used to mandate the presence of the Message-Authenticator
attribute on CoA/Disconnect-Request packets.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Trying to open file for checking file existence seems to be too much.
Instead use access system call which is meant for the same.
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
body_type, used to index in mka_body_handler, can be any u8 value, but
we have only ARRAY_SIZE(mka_body_handler) elements.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This uses a more accurate variable type for body_type and makes it
cleaner to compare this to other unsigned values.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the memory allocation in ieee802_1x_kay_init_receive_sc() fails, we
end up in an inconsistent state where the peer is moved to the live
peers list and its sci is setup, but we don't have an rxsc.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
The room we actually use is length. This could also mess up the
receiver, since it will advance by the actual length (as indicated by
the parameter body's length), which could differ from the offset at
which we stored the next item.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
1. The comparison between SCI's of two servers with identical priority
is broken, and would always return TRUE. Just use os_memcmp(), which
provides the ordering we need.
2. If no peer can be key server but this instance can, then become the
key server.
3. The ordering of blocks between peer as key server and ourself as key
server overwrites settings. Simple reordering fixes this.
4. Default to being the key server, so that we advertise our ability in
the MKPDUs we send. That's the only way peers can know we can be key
server. Cleared automatically as soon as we find a better peer.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
There's no need to have a separate variable and open-code a more
complicated version of this, just use is_broadcast_ether_addr().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation for adding further command completion support
to hostapd_cli move some cli related utility functions out of
wpa_cli into a new common cli file.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
This commit defines QCA vendor subcommand and attributes for IE based
access control, i.e., the specific configured IE (full IE) is matched
with the frames originated by the Wi-Fi STA / AP to accept or deny the
connection. A specific IE can either be a whitelist or blacklist.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces a new vendor sub command
QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND and associated
attributes to configure GPIO pins.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_supplicant set default scan IEs to the driver (if the
vendor command is supported). The driver can use these IEs in the scan
requests initiated by the driver itself. Also the driver can merge these
IEs into further scan requests that it receives, in case if the scan
request doesn't carry any of the IEs sent in this command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, HT/VHT state was shown in STATUS based on the configuration
parameter instead of the runtime operational parameters. This could
result in claiming HT/VHT to be enabled even when it was forced to be
disabled due to an incompatible configuration. Clear HT/VHT information
in the STATUS output if HT/VHT has been disabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If params->freq is NULL here, it leads to a segfault. Do not initialize
bss->bandwidth if params->freq is NULL.
Signed-off-by: Chaitanya T K <Chaitanya.Mgit@gmail.com>
Previously, HT capability IE and HT information IE were included in
Beacon and Mesh Peering Open/Confirm frames even if HT is disabled with
disable_ht=1. This patch removes these.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
If a peer stops sending adv_service_instance, we should clear the
existing dev->info.p2ps_instance.
This commit fixes the following scenario:
When peer device stops sending adv_service_instance, wpa_supplicant did
not remove old dev->info.p2ps_instance from device's property. This
variable should be updated as per peer behavior and should be cleared
when peer stops sending this information.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
Remove the unnecessary os_free() call from p2p_deinit() since
p2p_flush() called just above this takes care of freeing
p2p->after_scan_tx and the second call here ends up being no-op
os_free(NULL) in practice.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
reports mesh peer AID to kernel.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This commit introduces a new vendor sub command
QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH and associated
attributes which aim to configure selected frequencies on which the AP
can conditionally switch onto for preferred operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 49fe2ada20 ('OpenSSL: Support
OpenSSL 1.1.0 DH opacity') started using the new accessor functions, but
used incorrect success check for the DH_set0_key() call. This resulted
in dh5_init_fixed() failures and double-free on error path if the build
was linked against OpenSSL 1.1.0. Fix this by checking DH_set0_key()
return value to be 1 for the success case.
Signed-off-by: Jouni Malinen <j@w1.fi>
These control interface event message are used by external programs, so
define them a bit more formally in the header file.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows P2P Listen to be offloaded to device to enhance power
saving.
To start P2P listen offload, from wpa_cli interface, issue the command:
p2p_lo_start <freq> <period> <interval> <count>
To stop P2P listen offload, issue the command:
p2p_lo_stop
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Provides operating frequency in EVENT_ASSOC when IBSS is joined so that
wpa_s->assoc_freq can be updated when any IBSS network is joined.
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
During the P802.11s draft development, there were separate LISTEN and
IDLE states. However, the current IEEE 802.11 standards uses only the
IDLE state while the implementation called this LISTEN. Rename the state
in the implementation to match the one used in the standard to avoid
confusion. In addition, rename OPEN_{SENT,RCVD} to OPN_{SNT,RCVD} to
match the exact spelling of these states in the standard.
Signed-off-by: Jouni Malinen <j@w1.fi>
OpenSSL 1.1.0 (master branch) apparently ended up modifying the API
after the beta 2 release that was supposed to complete the work. Mark
the variables const to fix the compilation with the modified OpenSSL
API.
Signed-off-by: Jouni Malinen <j@w1.fi>
These elements can be used for pre-standard publication testing of HE
before P802.11ax draft assigns the element ID. The payload of these
vendor specific elements is defined by the latest P802.11ax draft.
Please note that the draft is still work in progress and the element
payload is subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is now annotated as be16, so use it as such in all cases instead of
first storing host byte order value and then swapping that to big endian
in other instances of the same structure. This gets rid of number of
sparse warnings.
Signed-off-by: Jouni Malinen <j@w1.fi>
driver_wired.c pulls in utils/common.h before net/if.h as a workaround
for NetBSD build. This results in IFNAMSIZ getting redefined and sparse
warning about this. Silence that warning by undefining the IFNAMSIZ
definition from common.h to allow the one from net/if.h being used. In
addition, remove duplicated inclusion of net/if.h.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of a sparse warning and also allows the compatibility of
the declarations to be verified (a missing const declaration is fixed
here as well).
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of number of sparse warnings and also allows the
compatibility of the declarations to be verified (number of missing
const declarations are fixed here as well).
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the compiler to check that function prototypes match the
implementation. In addition, this gets rid of sparse warnings.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are called through function pointers, so no need to make the
function symbols directly available outside this file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This converts some of the PAE code to use a design that gets rid
unnecessary warnings from sparse and allows more thorough validation of
byte order operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are called through function pointers, so no need to make the
function symbols directly available outside this file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These little endian fields were not marked properly and the type case in
the get_unaligned_* helper macros were causing warnings from sparse.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Couple of fsts_id and llt fields were not properly swapped from host
byte order to little endian byte order used in the frames. Fix this and
use the le32 type to make this more consistent and verifiable with
sparse.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since crypto_openssl.c is now implementing couple of functions
internally, pull in the relevant header files md5.h and aes_wrap.h to
make sure the function declaration are consistent.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Freeing memory for subjectAltName in parse_cert(), will give cert_cb
pointers to freed memory zone that may already been overwritten. Memory
for subjectAltName is released in parse_cert_free().
Signed-off-by: Cedric Izoard <cedric.izoard@ceva-dsp.com>
The "Accepting Additional Mesh Peerings bit == 0" means the peer cannot
accept any more peers, so suppress attempt to open a connection to such
a peer.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This moves pairwise, group, and management group ciphers to various mesh
data structures to avoid having to hardcode cipher in number of places
through the code. While CCMP and BIP are still the hardcoded ciphers,
these are now set only in one location.
Signed-off-by: Jouni Malinen <j@w1.fi>
The AMPE element includes number of optional and variable length fields
and those cannot really be represented by a fixed struct
ieee80211_ampe_ie. Remove the optional fields from the struct and
build/parse these fields separately.
This is also adding support for IGTKdata that was completely missing
from the previous implementation. In addition, Key RSC for MGTK is now
filled in and used when configuring the RX MGTK for a peer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation was incorrect in forcing the MGTK to be used
as the IGTK as well. Define new variable for storing IGTK and use that,
if set, to configure IGTK to the driver. This commit does not yet fix
AMPE element parsing to fill in this information.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the data structures to allow variable length MGTK to be
stored for RX. This is needed as an initial step towards supporting
different cipher suites.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is initial step in fixing issues in how PMF configuration for RSN
mesh was handled. PMF is an optional capability for mesh and it needs to
be configured consistently in both hostapd structures (to get proper
RSNE) and key configuration (not included in this commit).
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 0603bcb7fe ('hostapd: Process MAC
ACLs on a station association event (SME in driver)') processes MAC ACL
on a station association event for drivers which use AP SME offload but
does not consider the scenario where the drivers offload ACL. This can
result in station disconnection, though the driver accepts the
connection. Address this by avoiding the hostapd ACL check for the
drivers offloading MAC ACL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit also introduces a new attribute MANDATORY_FREQUENCY_LIST
which aims for AP operation in a channel that ensures best concurrency
sessions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
eloop deinit calls could trigger segmentation fault if the early error
path is hit before eloop_init() gets called.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that fst_global_init() has been called before deinitializing the
global FST context. This makes it a bit easier to handle failure paths
from initialization.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set max peer links to kernel even when wpa_supplicant MPM is used. This
sets the correct value for the "Accepting Additional Mesh Peerings bit"
in "Mesh Capability field" in "Mesh Configuration element" in the Beacon
frame.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Recent versions of engine_pkcs11 are set up to be autoloaded on demand
with ENGINE_by_id() because they don't need explicit configuration.
But if we *do* want to explicitly configure them with a PKCS#11 module
path, we should still do so.
We can't tell whether it was already initialised, but it's harmless to
repeat the MODULE_PATH command if it was.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Michael Schaller <misch@google.com>
Any data accessible from nla_data() is freed before the
send_and_recv_msgs() function returns, therefore we need to allocate
space for info.flags ourselves.
Signed-off-by: Paul Stewart <pstew@google.com>
gas_address3=1 can now be used to force hostapd to use the IEEE 802.11
standards compliant Address 3 field value (Wildcard BSSID when not
associated) even if the GAS request uses non-compliant address (AP
BSSID).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously all TX status events with wildcard BSSID were ignored. This
did not allow Public Action frame TX status to be processed with the
corrected wildcard BSSID use. Fix this to be allowed. In practice, this
affects only test cases since Action frame TX status was not used for
anything else.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11-2012, 10.19 (Public Action frame addressing) specifies
that the wildcard BSSID value is used in Public Action frames that are
transmitted to a STA that is not a member of the same BSS. hostapd used
to use the actual BSSID value for all such frames regardless of whether
the destination STA is a member of the BSS.
Fix this by using the wildcard BSSID in cases the destination STA is not
a member of the BSS. Leave group addressed case as-is (i.e., the actual
BSSID), since both values are accepted. No such frames are currently
used, though.
This version is still using the AP BSSID value in the Address 3 field
for GAS response frames when replying to a GAS request with AP BSSID
instead of Wildcard BSSID. This is left as a workaround to avoid
interoperability issues with deployed STA implementations that are still
using the non-compliant address and that might be unable to process the
standard compliant case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds the necessary changes to support extraction and use of the
extended capabilities specified per interface type (a recent
cfg80211/nl80211 extension). If that information is available,
per-interface values will be used to override the global per-radio
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new "timeout" argument to the event message if the nl80211 message
indicates that the connection failure is not due to an explicit AP
rejection message. This makes it easier for external programs to figure
out why the connection failed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the simplest case of SAE group negotiation to occur by
selecting the next available group if the peer STA indicates the
previous one was not supported. This is not yet sufficient to cover all
cases, e.g., when both STAs need to change their groups, but at least
some cases are no covered.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd deinit functions were not ready to handle a case where the data
structures were not fully initialized. Make these more robust to allow
wpa_supplicant mesh implementation to use the current deinit design in
OOM error cases without causing NULL pointer dereferences.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids internal access of structs and also removes the dependency
on the reimplemented TLS PRF functions when EAP-FAST support is not
enabled. Notably, BoringSSL doesn't support EAP-FAST, so there is no
need to access its internals with openssl_get_keyblock_size().
Signed-Off-By: David Benjamin <davidben@google.com>
Most protocols extracting keys from TLS use RFC 5705 exporters which is
commonly implemented in TLS libraries. This is the mechanism used by
EAP-TLS. (EAP-TLS actually predates RFC 5705, but RFC 5705 was defined
to be compatible with it.)
EAP-FAST, however, uses a legacy mechanism. It reuses the TLS internal
key block derivation and derives key material after the key block. This
is uncommon and a misuse of TLS internals, so not all TLS libraries
support this. Instead, we reimplement the PRF for the OpenSSL backend
and don't support it at all in the GnuTLS one.
Since these two are very different operations, split
tls_connection_prf() in two. tls_connection_export_key() implements the
standard RFC 5705 mechanism that we expect most TLS libraries to
support. tls_connection_get_eap_fast_key() implements the
EAP-FAST-specific legacy mechanism which may not be implemented on all
backends but is only used by EAP-FAST.
Signed-Off-By: David Benjamin <davidben@google.com>
Commit 68ae4773a4 ('OpenSSL: Use library
wrapper functions to access cert store') fixed most of these, but missed
a few.
Signed-Off-By: David Benjamin <davidben@google.com>
This makes changes such that hostapd (and wpa_supplicant AP mode)
registers to kernel for specific Action frames instead of generically
registering for all Action frames. This makes it easier for other
programs to register for some Action frames that hostapd does not handle
today without having to somehow coordinate directly with hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add P2PS config flag only when config_methods are set. This restores the
pre-P2PS behavioer for the cases where Display or Keypad config method
is specified for a peer (i.e., do not add the new P2PS method in that
case).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
eap_proto_sake_errors test case where the result was used after the
failed eap_sake_compute_mic() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
eap_proto_pax_errors test case where the result was used after the
failed eap_pax_mac() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
eap_proto_fast_errors test case where the result was used after the
failed sha1_t_prf() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
wpas_ctrl_error test case where the result was used after the failed
sha256_vector() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
hostapd_oom_wpa2_eap_connect test case where the result is used after
failed md5_vector() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
hostapd_oom_wpa2_eap_connect test case where memcmp is used after failed
hmac_md5() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
hostapd_oom_wpa2_eap test case where memcmp is used after failed
md5_vector() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Check for hmac_sha256() failures and exit from wps_derive_psk() without
printing out the derived keys if anything fails. This removes a valgrind
warning on uninitialized value when running the ap_wps_m3_oom test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In some terminal, verified with gtkterm and teraterm, backspace key is
not properly processed. For instance, type 'abc', 3 times of backspace
key press then '123' shows the result of 'abc123' instead of '123'. To
fix this, add a routine to process '\b' character input when using
edit_simple.c instead of edit.c (i.e., without CONFIG_WPA_CLI_EDIT=y).
Signed-off-by: Siwon Kang <kkangshawn@gmail.com>
If there's ever a driver that, like nl80211, requires radiotap,
we need to have a NEED_RADIOTAP variable to avoid trying to link
the radiotap helpers twice. Introduce that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Commit 4104267e81 ('Fix memory leak on NFC
DH generation error path') modified the generic (non-OpenSSL)
implementation of dh5_init() to free the previously assigned public key,
if any. However, that commit did not modify the OpenSSL specific version
of this function. Add the same change there to maintain consistent
behavior between these two implementations of the same function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 4104267e81 ('Fix memory leak on NFC
DH generation error path') modified dh5_init() behavior in the
non-OpenSSL implementation to free the public key (if any was previously
set). However, this did not update one of the callers to make sure the
publ argument in the call is initialized. This could result in trying to
free invalid pointer and segmentation fault when hostapd or
wpa_supplicant was built against some other crypto library than OpenSSL.
Signed-off-by: Rujun Wang <chinawrj@gmail.com>
BoringSSL added OpenSSL 1.1.0's SSL_get_client_random() and friends in
working towards opaquifying the SSL struct. But it, for the moment,
still looks more like 1.0.2 than 1.1.0 and advertises
OPENSSL_VERSION_NUMBER as such. This means that there is no need to
define those in BoringSSL and defining them causes conflicts. (C does
not like having static and non-static functions with the same name.)
As requested, this is conditioned on defined(BORINGSSL_API_VERSION) so
wpa_supplicant may continue to support older BoringSSLs for a time.
(BoringSSL revisions without the accessors predate BoringSSL maintaining
a BORINGSSL_API_VERSION.)
Also add a missing opensslv.h include. tls_openssl.c is sensitive to
OPENSSL_VERSION_NUMBER, so it should include the header directly rather
than rely on another header to do so.
Signed-off-by: David Benjamin <davidben@google.com>
Spurious newlines output while writing the config file can corrupt the
wpa_supplicant configuration. Avoid writing these for the network block
parameters. This is a generic filter that cover cases that may not have
been explicitly addressed with a more specific commit to avoid control
characters in the psk parameter.
Signed-off-by: Paul Stewart <pstew@google.com>
WPA/WPA2-Personal passphrase is not allowed to include control
characters. Reject a Credential received from a WPS Registrar both as
STA (Credential) and AP (AP Settings) if the credential is for WPAPSK or
WPA2PSK authentication type and includes an invalid passphrase.
This fixes an issue where hostapd or wpa_supplicant could have updated
the configuration file PSK/passphrase parameter with arbitrary data from
an external device (Registrar) that may not be fully trusted. Should
such data include a newline character, the resulting configuration file
could become invalid and fail to be parsed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
One of supported code paths already allows this scenario. It is used if
driver doesn't report NL80211_ATTR_DEVICE_AP_SME and doesn't support
monitor interface. In such situation:
1) We don't quit if subscribing for WLAN_FC_STYPE_PROBE_REQ fails
2) We don't try subscribing for WLAN_FC_STYPE_ACTION
3) We fallback to AP SME mode after failing to create monitor interface
4) We don't quit if subscribing for WLAN_FC_STYPE_PROBE_REQ fails
Above scenario is used, e.g., with brcmfmac. As you can see - thanks to
events provided by cfg80211 - it's not really required to receive Probe
Request or action frames.
However, the previous implementation did not allow using hostapd with
drivers that:
1) Report NL80211_ATTR_DEVICE_AP_SME
2) Don't support subscribing for PROBE_REQ and/or ACTION frames
In case of using such a driver hostapd will cancel setup after failing
to subscribe for WLAN_FC_STYPE_ACTION. I noticed it after setting flag
WIPHY_FLAG_HAVE_AP_SME in brcmfmac driver for my experiments.
This patch allows working with such drivers with just a small warning
printed as debug message.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
This reduces duration that private keying material might remain in the
process memory by clearing wpabuf data used in WPS operations when there
is possibility of the buffer including keys or related material.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new parameter allows hostapd to add Vendor Specific elements into
(Re)Association Response frames similarly to the way vendor_elements
parameter can be used for Beacon and Probe Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The OpenSSL 1.1.0 Beta 2 release made DH opaque and that broke
compilation of crypto_openssl.c. Fix this by using the new accessor
functions when building against OpenSSL 1.1.0 or newer.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 66d464067d ('FT: Register RRB
l2_packet only if FT-over-DS is enabled') disabled RRB l2_packet socket
if ft_over_ds is disabled, but this socket is required for FT
over-the-air, too (FT key distribution). Enable the socket regardless of
ft_over_ds setting if FT is enabled.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
This adds QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION and the attributes used
with these commands.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows local GO to fetch the P2P Interface Address of a P2P Client
in the group based on the P2P Device Address for the client. This
command should be sent only on a group interface (the same peer may be
in multiple concurrent groups).
Usage:
P2P_GROUP_MEMBER <P2P Device Address>
Output:
<P2P Interface Address>
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Trigger an event when wpa_supplicant accepts an invitation to re-invoke
a persistent group. Previously wpa_supplicant entered group formation
without triggering any specific events and it could confuse clients,
especially when operating with a driver that does not support
concurrency between P2P and infrastructure connection.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
The os_snprintf() call here cannot really fail in practice, but since
its result was stored into the local variable and not checked, static
analyzers could warn about the unused assignment. Clean this up by
checking the return value.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set the global RRM flag if global RRM is supported by the device. Also,
allow RRM in (Re)Association Request frame if the global RRM flag is
set.
Signed-off-by: Beni Lev <beni.lev@intel.com>
This flag indicates that RRM can be used in (Re)Association Request
frames, without supporting quiet period.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Register to receive Radio Measurement Request frames since LCI request
is supported by wpa_supplicant.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add FTM range request via RRM. The AP sends Radio measurement request
with FTM range request as a request for the receiving STA to send FTM
requests to the given list of APs. The neighbor report part of the
request is taken from the neighbor database.
The control interface command is:
REQ_RANGE <dst addr> <rand_int> <min_ap> <responder> [<responder>..]
dst addr: MAC address of an associated STA
rand_int: Randomization Interval (0..65535) in TUs
min_ap: Minimum AP Count (1..15); minimum number of requested FTM ranges
between the associated STA and the listed APs
responder: List of BSSIDs for neighboring APs for which a measurement
is requested
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a hostapd control interface command REQ_LCI to request LCI from an
associated station using radio measurement.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Save RM enabled capability element of an associating station if radio
measurement is supported in its capability field.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Process Neighbor Report Request frame and send Neighbor Report Response
frame based on the configured neighbor report data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a configurable neighbor database that includes the content of
Nighbor Report element, LCI and Location Civic subelements and SSID.
All parameters for a neighbor must be updated at once; Neighbor Report
element and SSID are mandatory, LCI and civic are optional. The age of
LCI is set to the time of neighbor update.
The control interface API is:
SET_NEIGHBOR <BSSID> <ssid=SSID> <nr=data> [lci=<data>] [civic=<data>]
To delete a neighbor use:
REMOVE_NEIGHBOR <BSSID> <SSID>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Extend the radio_measurements parameter to save all the supported
RRM capabilities as it's used in RM enabled capabilities element.
Make this parameter not directly configurable via config file (though,
keep the radio_measurements parameter for some time for backwards
compatibility). Instead, add a configuration option to enable neighbor
report via radio measurements. Other features can be added later as
well.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a function that parses SSID in text or hex format. In case of the
text format, the SSID is enclosed in double quotes. In case of the hex
format, the SSID must include only hex digits and not be enclosed in
double quotes. The input string may include other arguments after the
SSID.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Make the function available as part of the wpabuf API.
Use this renamed function where possible.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
The hostapd "POLL_STA <addr>" control interface command can be used to
check whether an associated station ACKs a QoS Data frame. The received
ACK for such a frame is reported as an event message ("AP-STA-POLL-OK
<addr>").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The optional tx=0 parameter can be added to the hostapd
DEAUTHENTICATE/DISASSOCIATE command to request disconnection without
transmitting the Deauthentication/Disassociation frame to the STA.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external programs to fetch the driver inactivity value for a
specific STA ("STA <addr>" hostapd control interface command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new VENDOR_ELEM value 14 can now be used to add a vendor element
into Probe Request frames used by non-P2P active scans.
For example:
VENDOR_ELEM_ADD 14 dd05001122330a
and to clear that:
VENDOR_ELEM_REMOVE 14 *
Signed-off-by: Jouni Malinen <j@w1.fi>
Implement configure_data_frame_filters() callback by using
the net-sysfs interfaces (if these are available).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add a new function declaration that will allow wpa_supplicant to request
the driver to configure data frame filters for specific cases.
Add definitions that will allow frame filtering for stations as
required by Hotspot 2.0:
1. Gratuitous ARP
2. Unsolicited NA
3. Unicast IP packets encrypted with GTK
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
If a legacy client with no P2P PS support is trying to connect to
a P2P GO, the driver should know that, and change its PS behavior
accordingly.
Add a parameter to hostapd_sta_add_params() indicating if P2P PS is
supported by the station and pass this parameter to kernel with nl80211
driver when the station is added/set.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Fix a possible memory leak in decode_tunnel_passwords() if an invalid
passphrase is received from the RADIUS server.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
This was previously handled for the case where the non-success
Invitation Response frame was sent out during the Listen phase. However,
in the case the Action frame TX ended up getting scheduled when the
Search phase scan had already started (e.g., due to the driver reporting
Invitation Request RX late enough for the Listen-to-Search transition
having already started), the postponed Action frame TX status processing
did not cover the specific case of non-success Invitation Response. This
could result in the p2p_find operation getting stopped (stuck in SEARCH
state) unexpectedly.
Fix this by calling p2p_check_after_scan_tx_continuation() from
Invitation Response TX callback handler if the invitation was rejected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The Secure bit in the Key Information field of EAPOL-Key frames is
supposed to be set to 1 when there is a security association. This was
done for other frames, but not for the EAPOL-Key Request frame where
supplicant is requesting a new PTK to be derived (either due to Michael
MIC failure report Error=1 or for other reasons with Error=0). In
practice, EAPOL-Key Request frame is only sent when there is a PTK in
place, so all such frames should have Secure=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
This struct in the union is empty, but the design of using a zero-length
u8 array here is not fully compatible with C++ and can result in
undesired compiler warnings. This struct is not used anymore, so it can
be removed from the struct ieee80211_mgmt definition to complete the
changes started in commit d447cd596f
('Updates for stricter automatic memcpy bounds checking').
Signed-off-by: Jouni Malinen <j@w1.fi>
This struct in the union is empty, but the design of using a zero-length
u8 array here is not fully compatible with C++ and can result in
undesired compiler warnings. Since there are no non-IE fields in the
Probe Request frames, get the location of the variable length IEs simply
by using the pointer to the frame header and the known header length.
Signed-off-by: Jouni Malinen <j@w1.fi>
This struct in the union is empty, but the design of using a zero-length
u8 array here is not fully compatible with C++ and can result in
undesired compiler warnings. Since there are no non-IE fields in the
Probe Request frames, get the location of the variable length IEs simply
by using the pointer to the frame header and the known header length.
Signed-off-by: Jouni Malinen <j@w1.fi>
This reverts commit 4ca16b5fd7.
Configuration for this will be done using a previously assigned more
generic command. This new command
QCA_NL80211_VENDOR_SUBCMD_SET_TXRX_AGGREGATION has not been used in any
driver version and won't be used, so the assigned command id can be
freed for future use.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no strong need for pulling in linux/if_ether.h here since all
that is needed if ETH_P_IP and we already cover multiple other ETH_P_*
values in utils/common.h.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was only used for providing an option to use linux/if_packet.h
instgead of netpacket/packet.h in src/ap/iapp.c. However,
netpacket/packet.h is nowadays commonly available and hostapd already
depends on it through src/l2_packet/l2_packet_linux.c, so there is no
need to continue to provide this option for the kernel header.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of need to include linux/if_vlan.h and additional defines
in vlan_ioctl.c to avoid issues with missing definitions in libc
headers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Due to both <netinet/in.h> (in "utils/includes.h") and <linux/in6.h> (in
<linux/if_bridge.h>) being included, the in6_addr is being redefined:
once from the C library headers and once from the Linux kernel headers.
This causes some build failures with for example the musl C library:
In file included from /usr/include/linux/if_bridge.h:18,
from ../src/ap/vlan_init.c:17:
/usr/include/linux/in6.h:32: error: redefinition of 'struct in6_addr'
/usr/include/linux/in6.h:49: error: redefinition of 'struct sockaddr_in6'
/usr/include/linux/in6.h:59: error: redefinition of 'struct ipv6_mreq'
Mixing C library and Linux kernel headers is a bit problematic [1] and
should be avoided if possible [2]. In order to fix this, define just the
macros needed from <linux/if_bridge.h> as done in Busybox for the brctl
applet [3].
[1] https://sourceware.org/bugzilla/show_bug.cgi?id=15850
[2] http://www.openwall.com/lists/musl/2015/10/06/1
[3] https://git.busybox.net/busybox/commit/?id=5fa6d1a632505789409a2ba6cf8e112529f9db18
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
With this, vlan_init.c does not need any special header files anymore
and vlan_ifconfig.c does not need hostapd-specific header files that
might conflict with net/if.h on NetBSD.
Signed-off-by: Jouni Malinen <j@w1.fi>
Move the ioctl-based VLAN implementation to a separate file to avoid
need for conditional blocks within vlan_ioctl.c. This removes the
internal CONFIG_VLAN_NETLINK define, i.e., this is now used only in
build configuration (.config) to select whether to include the
vlan_util.c (netlink) or vlan_ioctl.c (ioctl) implementation of the
functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
caddr_t is legacy BSD and should be avoided [1]. While glibc may still
use __caddr_t as the type, Linux kernel does not (it is "void __user *
ifru_data").
This fixes compile errors with the musl libc:
../src/ap/vlan_init.c: In function 'br_delif':
../src/ap/vlan_init.c:218:18: error: '__caddr_t' undeclared (first use in this function)
ifr.ifr_data = (__caddr_t) args;
[1] http://stackoverflow.com/questions/6381526/what-is-the-significance-of-caddr-t-and-when-is-it-used
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
cfg80211 reports a deauth/disassoc event when internally clearing
connection with the previous BSS. Ignore that event to allow the new
connect command to complete.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier for drivers that use the Connect command instead of
separate Auth+Assoc commands to determine when to use reassociation
instead of association. Matching changes are still needed in cfg80211 to
allow this parameter to be used, but it is safe for wpa_supplicant to
start including this attribute now since it will be ignored by older
cfg80211 versions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
pmksa->pmk or pmksa->pmkid cannot be NULL since they are arrays. Remove
the unnecessary NULL checks and use the provided pmksa pointer directly
to simplify the implementation. (CID 138519)
Signed-off-by: Jouni Malinen <j@w1.fi>
Interface additions/removals are not guaranteed to be for the driver
listening to the kernel events. As such, send the events to
wpa_supplicant_event_global() which can then pick the correct interface
registered with wpa_supplicant to send the event to.
Signed-off-by: Roy Marples <roy@marples.name>
Commit 1889af2e0f ('VLAN: Separate station
grouping and uplink configuration') added an ap_sta_set_vlan() function
that gets called from pmksa_cache_auth.c. This broke CONFIG_IBSS_RSN=y
build if src/ap/sta_info.c did not get included in the build, i.e., if
CONFIG_AP=y was not set.
Fix this by making the ap_sta_set_vlan() call conditional on
CONFIG_NO_VLAN being undefined and define this for CONFIG_IBSS_RSN=y
builds. This is fine for wpa_supplicant since CONFIG_AP=y case was
already defining this. For hostapd, this function call is not needed for
CONFIG_NO_VLAN case either.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This patch add functionality of mesh SAE PMKSA caching. If the local STA
already has peer's PMKSA entry in the cache, skip SAE authentication and
start AMPE with the cached value.
If the peer does not support PMKSA caching or does not have the local
STA's PMKSA entry in the cache, AMPE will fail and the PMKSA cache entry
of the peer will be removed. Then STA retries with ordinary SAE
authentication.
If the peer does not support PMKSA caching and the local STA uses
no_auto_peer=1, the local STA can not retry SAE authentication because
NEW_PEER_CANDIDATE event cannot start SAE authentication when
no_auto_peer=1. So this patch extends MESH_PEER_ADD command to use
duration(sec). Throughout the duration, the local STA can start SAE
authentication triggered by NEW_PEER_CANDIDATE even though
no_auto_peer=1.
This commit requires commit 70c93963ed
('SAE: Fix PMKID calculation for PMKSA cache'). Without that commit,
chosen PMK comparison will fail.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA_FLUSH control interface command to
allow the PMKSA list from the authenticator side to be flushed for AP
and mesh mode. In addition, this adds a hostapd PMKSA_FLUSH control
interface command to flush the PMKSA entries.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA control interface command to allow
the PMKSA list from the authenticator side to be listed for AP and mesh
mode. In addition, this adds a hostapd PMKSA control interface command
to show the same list for the AP case.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This group capability bit was previously added unconditionally which
could result in the P2P Client assuming the functionality is available
even though the GO would always reject the request (not reply to it with
an assigned IP address) during the 4-way handshake.
Fix this by advertising the capability only if the GO configuration
allow IP address assignment to be completed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 732b1d20ec ('nl80211: Clean up
ifidx properly if interface in a bridge is removed') added
drv->if_indices_reason array similarly to the previously used
drv->if_indices. However, it had a copy-paste error here on the error
path where a reallocation failure after at least one successful
reallocation would result in the drv->if_indices being overridden
instead of restoring drv->if_indices_reason to the old value. Fix this
by setting the correct variable on the error path. (CID 138514)
Signed-off-by: Jouni Malinen <j@w1.fi>
SMPS mode is applicable only for HT and including an attribute to
configure it when HT is disabled could result in the AP start operation
failing. Fix this by adding the attribute only in cases where HT is
enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since this function needs to allocate memory, it might fail. Check that
the returned memory pointer is not NULL before trying to parse the
output.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While this function could return NULL if the parameter issued to it were
NULL, that does not really happen here. Anyway, since this can result in
a warning from a static analyzer that does can see the return NULL
without fully understanding what it means here, check the return value
explicitly against NULL to avoid false warnings.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since commit cb05808c46 ('nl80211: Generic
Linux master interface support for hostapd'), hostapd is listening for
EAPOL frames on any master which the interface is enslaved under.
This commit allows hostapd to support network hierarchy in which the
interface is enslaved under some master which in turn is enslaved under
a bridge.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
In scenarios where only DFS channels are available (e.g., outdoor,
special country codes), hostapd must be able to handle situations
where all are unavailable.
The two possibilities to get there are
1) while operating on the last available DFS channel a radar is
detected
2) hostapd is started while all channels are unavailable
In both cases, hostapd instead of terminating should better
wait for the NOPs to pass and re-try operation after the CAC.
This patch provides that feature by using the condition
(iface->state == HAPD_IFACE_DFS && !iface->cac_started)
as NOP mode signature to retry operation from within
hostapd_dfs_nop_finished().
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Upon receiving FST setup request on old band, the peer is searched on
new band. The assumption is that MB IE from this peer on new band
previously received either in assoc event or in FST setup request.
There are cases in which above assumption doesn't work, peer is not
found and session setup fails. For example:
- STA connects over 11ac. Due to driver limitation, MB IE is not included
in assoc event
- STA connects over 11ad. MB IE included in assoc event.
- FST session established on 11ac band, with AP as initiator. i.e. FST
setup request sent in AP=>STA direction. STA searches for peer's (AP)
MB IE on 11ad band which exists.
- FST switch occur
- FST session established on 11ad band, with STA as initiator. i.e. FST
setup request sent in STA=>AP direction. AP searches for peer's (STA)
MB IE on 11ac band which are absent.
For fixing the above, consider also peers without MB IE as candidates in
the search algorithm.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
In the 60 GHz band, service discovery management frames are sent over
the control PHY and have a smaller maximum frame size (IEEE Std
802.11ad-2012, 21.4.3.2). Fix the code to use sufficiently small
fragment size when operating in the 60 GHz band.
The 60 GHz fragment size (928) is derived from the maximum frame size
for control PHY (1023) and subtracting 48 bytes of header size, and some
spare so we do not reach frames with the absolute maximum size.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Add a new 'use_driver_iface_addr' configuration parameter to allow use
of the default interface address generated by the driver on interface
creation. This can be useful when specific MAC addresses were allocated
to the device and we want to use them for multi-BSS operation.
Signed-off-by: Eliad Peller <eliad@wizery.com>
There is a race condition in which AP might receive the EAPOL-Start
frame (from the just-associated station) before the TX completion of the
Association Response frame. This in turn will cause the EAPOL-Start
frame to get dropped, and potentially failing the connection.
Solve this by saving EAPOL frames from authenticated-but-not-associated
stations, and handling them during the Association Response frame TX
completion processing.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Add UDP support for ctrl_iface:
New config option could be set:
CONFIG_CTRL_IFACE=udp
CONFIG_CTRL_IFACE=udp-remote
CONFIG_CTRL_IFACE=udp6
CONFIG_CTRL_IFACE=udp6-remote
And hostapd_cli usage:
hostapd_cli -i localhost:8877
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This is preparation for sharing a single implementation for ctrl_iface
functionality in wpa_supplicant and hostapd.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Update the peer WFD IE information based on WFD elements received in
Provision Discovery Response and GO Negotiation Response frames.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
In case a Probe Request frame is received from a known peer P2P Device,
update the listen channel based on the P2P attributes in the Probe
Request frame. This can be useful for cases where the peer P2P Device
changed its listen channel, and the local P2P device is about to start a
GO Negotiation or invitation signaling with the peer.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Currently, when scan is stuck in the kernel/driver/fw,
the nl80211 driver tries to recover by faking a SCAN_RESULTS flow.
However, the scan is still stuck in the kernel/driver/fw.
To avoid that stuck request, abort it upon scan timeout.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
syms is defined only for WPA_TRACE_BFD:
../src/utils/trace.c: In function ‘wpa_trace_deinit’:
../src/utils/trace.c:372:7: error: ‘syms’ undeclared (first use in this function)
free(syms);
^
../src/utils/trace.c:372:7: note: each undeclared identifier is reported only once for each function it appears in
make: *** [../src/utils/trace.o] Error 1
make: *** Waiting for unfinished jobs....
Add appropriate #ifdef.
Signed-off-by: Eliad Peller <eliad@wizery.com>
When building P2P IE for Probe Request frames in P2P scan, add the
device information attribute if the 60 GHz band is included in the scan,
since this is required by the P2P specification.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Expose the functions wpas_get_bands() and wpas_freq_to_band() and the
enum wpa_radio_work_band, since they will be needed outside
wpa_supplicant.c.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
STT guards the exchange of FST Action frames with the peer station.
It was observed that sometimes Action frames sending is delayed at
driver/FW layers for few hundreds millisec.
Enlarge the STT to overcome such cases.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
In case vendor ACS command returns invalid channel or hardware mode,
complete the interface setup with an error code instead of simply
return, so that hostapd can properly clean up the interface setup.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This tells to the server how long we have been trying to transmit the
message so that the actual time of the message generation can be
determined from receive time (ignoring network delays and only at
accuracy of one second).
For interim updates, only value 0 is used since there are no
retransmissions of the same message. For other accounting messages, the
initial attempt goes out with value 0 and the retransmissions, if
needed, show the number of seconds the message has been waiting in the
queue.
Update the Identifier and Authenticator in the messages whenever
updating the Acct-Delay-Time per RFC 2866, 4.1 requirements.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of using the RADIUS client retransmission design with the old
RADIUS message contents for each retry, trigger a completely new interim
accounting update instance more quickly (using the same schedule as
RADIUS message retransmissions) to improve accounting updates in cases
where RADIUS message delivery fails. This allows the server to get up to
date information from the time the "retry" message was sent instead of
the old information from the time the first failed attempt was sent.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to maintain two implementations of the functionality.
is_zero_ether_addr() is easier to understand, so use it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Using rtnl_link_alloc_cache() is expensive as it fills in all configured
links. Using rtnl_link_get_kernel() is much more lightweight.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
When an interface is removed while it was in a bridge, the bridge was
not removed from the local ifidx list.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
As the Linux variant of l2_packet_init() does not use its own_addr
argument and l2_packet_receive() does not filter on destination MAC
address, this needs to be checked in the callback.
If there are multiple BSSes listening for FT RRB packets, all their
BSSIDs need to be local to the bridge interface. As l2_packet_init() is
going to receive all of them going for any local address, those RRB
messages started turning up on BSSes that were not destinated for and
cluttering logs.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
If the AP is slow, passphrase hashing takes too long to serve the client
before timeout. Extend the Tunnel-Password design to allow a 64
character value to be interpreted as a PSK and send SSID to RADIUS
server. This allows the RADIUS server to either take care of passphrase
hashing or to use raw PSK without such hashing.
This is especially important for FT-PSK with FT-over-air, where hashing
cannot be deferred.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Instead of copying the full struct hostapd_sta_wpa_psk_short, share the
existing entry and use reference counting to check when it needs to be
freed. This allows caching of PSKs derived from passphrases to avoid
having to perform the heavy hashing operation multiple times.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Hashing takes quite some time (can be about one second on a low-power
CPU for each passphrase provided), so hostapd can easily hit the 900 ms
Wi-Fi client authentication deadline (mac80211 uses 3x 300 ms). This can
be fixed by storing the passphrase instead of PSK with the STA and defer
the hashing into the WPA/RSN 4-way handshake, when enumerating all PSKs.
This applies for the case where a RADIUS server is used to store the
per-STA passphrases and this passphrase is delivered as part of the MAC
ACL check during IEEE 802.11 Authentication frame processing.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The VLAN ifname is limited to the maximum length of IFNAMSIZ, so there
is no need to use heap allocation for it.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
r1_key_holder is an identifier that was always set to zero if unless
configured before.
See 11.6.1.7.4 of IEEE Std 802.11-2012 which reads
"R1KH-ID is a MAC address of the holder of the PMK-R1 in the
Authenticator of the AP"
See 12.2.2 of IEEE Std 802.11-2012 which reads
"Each R0KH-ID and R1KH-ID is assumed to be expressed as a unique
identifier within the mobility domain."
"The R1KH-ID shall be set to a MAC address of the physical entity
that stores the PMK-R1 ..."
Defaulting this to BSSID is a more reasonable value since we have not
rejected the missing r1_key_holder as invalid configuration.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
A malicious station could try to do FT-over-DS with a non WPA-enabled
BSS. When this BSS is located in the same hostapd instance, internal RRB
delivery will be used and thus the FT Action Frame will be processed by
a non-WPA enabled BSS. This processing used to crash hostapd as
hapd->wpa_auth is NULL. If the target BSS is on a different hostapd
instance, it will not listen for these packets and thus not crash.
Fix this by checking hapd->wpa_auth before delivery.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The FT RRB hostapd packets have a length field. For PULL frames, it
counted the bytes starting with nonce and up to the last before pad. For
RESP frames, it counted the bytes starting with nonce and up to the last
before pad except for 2 bytes. For PUSH frames, it counted the bytes
starting with nonce and up to including pad.
As rounding is done with AES encryption, including pad does not make
sense. Not including the last field before pad does not make sense
either. These were broken in the earlier addition of the 2 octet
pairwise field in commit 1b484d60e5 ('FT:
Include pairwise cipher suite in PMK-R0 SA and PMK-R1 SA').
AES encryption is not affected, as rounding hides the differences. The
packets data_length field is not used, so the differences have no effect
there.
This patch changes the constants to match the bytes used, thus excluding
the pad. To validate the changes, look at remainder modulo 8 of the sum
of the size constants and the padding sizes.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This makes hostapd track Supported Operating Classes information from
the associated STAs. The stored information is available through the STA
control interface command (supp_op_classes row) as a hexdump of the
Supported Operating Classes element starting from the Length field. This
information can be used as input to BSS transition management and
channel switching decisions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Inside management frame TX status callback, print the TX result where it
was missing. This is useful for debugging management frame drops.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
This adds parsing of non-preferred channel list on an MBO AP. The
information in (Re)Association Request and WNM Notification Request
frames is parsed to get the initial value and updates from each
associated MBO STA. The parsed information is available through the STA
control interface command non_pref_chan[i] rows.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the second memory allocation in ieee802_11_send_wnmsleep_resp() were
to fail and ieee80211_11_get_tfs_ie() succeed, the wnmtfs_ie allocation
would not have been freed on the error path.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While refactoring VLAN comparison into vlan_compare(), it was overlooked
that modifications are needed for tagged VLAN support.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
If WPA2 and MBO are enabled, PMF needs to be enabled in hostapd
configuration. If PMF is optional in the configuration, an MBO STA is
required to negotiate use of PMF.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes hostapd parse a received WNM Notification Request frame
subelements and if a WFA MBO cellular data capability subelement is
seen, update the cellular data capability for the STA.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes hostapd parse the MBO attribute in (Re)Association Request
frame and track the cellular data capability (mbo_cell_capa=<val> in STA
control interface command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This removes multiple copies of wpabuf_resize() following by
wpabuf_put_{buf,data}() with the help of two simple helper functions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add an option to add MBO IE to BSS Transition Management Request frame.
The MBO IE includes the transition reason code, cellular data connection
preference, and, if the disassoc imminent bit is set, it may also
include re-association retry delay. Otherwise, the re-association retry
delay should be set to zero.
The additional BSS_TM_REQ argument uses the following format:
mbo=<reason>:<reassoc delay>:<cell pref>
reason: 0-9
reassoc delay: 0-65535 (seconds; 0 = disabled)
cell pref: 0, 1, 255
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add MBO IE with AP capability attribute to Beacon, Probe Response, and
(Re)Association Response frames to indicate the AP supports MBO.
Add option to add Association Disallowed attribute to Beacon, Probe
Response, and (Re)Association Response frames. Usage:
SET mbo_assoc_disallow <reason code>
Valid reason code values are between 1-5. Setting the reason code to
0 will remove the Association Disallowed attribute from the MBO IE
and will allow new associations.
MBO functionality is enabled by setting "mbo=1" in the config file.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add the transition candidate list to BSS Transition Management Response
frame. The candidates preference is set using the regular wpa_supplicant
BSS selection logic. If the BSS transition request is rejected and
updated scan results are not available, the list is not added.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a function to derive phy type from frequency and bandwidth
as defined in IEEE Std 802.11ac-2013 Annex C (dot11PHYType).
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add parsing of MBO IE in BSS Transition Management Request frames. If
the MBO IE includes the association retry delay attribute, do not try to
reconnect to the current BSS until the delay time is over.
If the MBO IE includes the cellular data connection preference attribute
or the transition rejection reason attribute, send a message to upper
layers with the data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add definitions for global operating classes. These definitions will be
used to construct supported operating classes information element.
The operating classes definitions used locally for P2P module will be
removed and included in the general operating classes definitions.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a helper function to find a certain IE inside IEs buffer by ID and
use this function in several places that implemented similar
functionality locally.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The recent VLAN changes added an explicit code path that sets vlan_desc
= NULL within ap_sta_set_vlan(). This makes some code analyzers warn
about the debug print that could potentially dereference this pointer.
Silence that warning by verifying the pointer more consistently within
this function.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the driver supports 64-bit TX/RX byte counters, use them directly.
The old 32-bit counter extension is maintained for backwards
compatibility with older drivers.
For nl80211 driver interface, the newer NL80211_STA_INFO_RX_BYTES64 and
NL80211_STA_INFO_TX_BYTES64 attributes are used when available. This
resolves the race vulnerable 32-bit value wrap/overflow. Rework RADIUS
accounting to use these for Acct-Input-Octets, Acct-Input-Gigawords,
Acct-Output-Octets, and Acct-Output-Gigawords, these values are often
used for billing purposes.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Previously, stations were added to the driver only after the
(Re)Association Response frame was acked. In the time period between the
station has acked the (Re)Association Response frame and the time the
station was added to the kernel, the station can already start sending
Data frames, which will be dropped by the hardware/driver. In addition
to the data loss, the driver may ignore NDPs with PM bit set from this
STA.
Fix this by setting/adding the STA with associated flag set to the
driver before the AP sends the (Re)Association Response frame with
status success. If the (Re)Association Response frame wasn't acked,
remove the station from the driver.
Note that setting a station to associated state before the non-AP
station acknowledges the (Re)Association Response frame is not compliant
with the IEEE 802.11 standard that specifically states that a non-AP
station should transition to authenticated/associated state only after
it acknowledged the (Re)Association Response frame. However, this is a
justifiable simplification to work around the issue described above since
1. The station will be removed in case it does not acknowledge the
(Re)Association Response frame.
2. All Data frames would be dropped until the station is set to
authorized state and there are no known issues with processing the
other Class 3 frames during the short window before the
acknowledgement is seen.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add support for drivers that support full AP client state, i.e., can
handle adding stations that are not associated yet. For such drivers,
add a station after processing the authentication request, instead of
adding it in the association response callback.
Doing so is beneficial in cases where the driver cannot handle the add
station request, in which case it is useless to perform the complete
connection establishment.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
This provides means for determining whether the driver supports full AP
station state and setting the needed STA flags for using this
functionality.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Do not use os_random() that uses a low quality PRNG to generate the
anti-clogging token. The construction can be improved upon by replacing
it with a call to os_get_random(), which uses a high quality PRNG. While
the RFC 5931 explictly recommends not to do this ("SHOULD NOT be from a
source of random entropy"), it does still mandate unpredicability ("MUST
be unpredictable"). The anti-clogging token is most unpredictable when
it is taken from a high quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Remove the fallback dependency on os_random() from the code that gets a
valid DFS channel. This is exceptionally unlikely to ever be called as
the call to os_get_random() is unlikely to fail. The intention is to
facilitate future removal of os_random() as it uses a low quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Remove the fallback dependency on os_random() when generating a WPS pin.
This is exceptionally unlikely to ever be called as the call to
os_get_random() is unlikely to fail. The intention is to facilitate
future removal of os_random() as it uses a low quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Do not use the system clock or os_random() that uses a low quality PRNG
as part of the pseudo-random challenge in auth_shared_key(). The
construction can be improved upon by replacing it with a call to
os_get_random(), which uses a high quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Previously, only mesh Action frames from BLOCKED STA were dropped.
Extend that to drop Authentication frames as well.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The SAE PMKID is calculated with IEEE Std 802.11-2012 11.3.5.4, but the
PMKID was re-calculated with 11.6.1.3 and saved into PMKSA cache. Fix
this to save the PMKID calculated with 11.3.5.4 into the PMKSA cache.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Ensure that characters are represented as unsigned char when using
isblank() and isspace(). These function take in a "int c" argument, but
it needs to be unsigned for the cases where EOF is not indicated.
Signed-off-by: Roy Marples <roy@marples.name>
Shuffle includes above system ones so to fix a compile issue
on NetBSD where the if_type #define from <net/if.h>
conflicts with the wpa_driver_if_type enum.
Signed-off-by: Roy Marples <roy@marples.name>
Shuffle wpa_supplicant includes above system ones so that
to fix a compile problem on NetBSD where if_type #define
conflicts with the wpa_driver_if_type enum.
Signed-off-by: Roy Marples <roy@marples.name>
While most C libraries print "(null)" when NULL is used as an argument
to printf format string %s, this is not really necessary to print here,
so move the debug print to be after the NULL check.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the stations to be assigned to their own vif. It does not
need dynamic_vlan to be set. Make hostapd call ap_sta_set_vlan even if
!vlan_desc.notempty, so vlan_id can be assigned regardless.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This makes vlan_newlink() and vlan_dellink() add tagged VLANs to AP_VLAN
interfaces as given by struct vlan_description.
hostapd_vlan_if_remove() is done in vlan_dellink() as tagged interfaces
need to be removed before the interface can be deleted and a DELLINK
message can be generated.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
To prepare for adding tagged VLAN support in vlan_init.c, vlan_newlink()
and vlan_dellink() are split into multiple functions. This reduces
indention and eases adding tagged VLANs as well.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
1. Add tagged VLAN to struct vlan_description
(compile limited number of tagged VLANs per description)
For k tagged VLANs, the first k entries in vlan_description.tagged
are used. They are sorted in ascending order. All other entries are
zero. This way os_memcmp() can find identical configurations.
2. Let tagged VLANs be parsed from RADIUS Access-Accept
3. Print VLAN %d+ with %d=untagged VID if tagged VLANs are set
4. Select an unused vlan_id > 4096 for new tagged VLAN configurations
5. Add EGRESS_VLAN RADIUS attribute parsing also for untagged VLANs
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
