jeltz/hostap
1
0
Fork 0
Code Issues Pull requests Projects Releases Wiki Activity

Sync with mac80211-next.git include/uapi/linux/nl80211.h

Browse source 
This brings in nl80211 definitions as of 2016-12-02.

Signed-off-by: Jouni Malinen <j@w1.fi>
This commit is contained in:
Jouni Malinen 2016-12-04 20:50:07 +02:00
parent 08032c7418
commit 5f2c0a22a9
1 changed files with 29 additions and 0 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

29
src/drivers/nl80211_copy.h
View file

@ -600,6 +600,20 @@
*
* @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface.
*
* @NL80211_CMD_SET_MULTICAST_TO_UNICAST: Configure if this AP should perform
* multicast to unicast conversion. When enabled, all multicast packets
* with ethertype ARP, IPv4 or IPv6 (possibly within an 802.1Q header)
* will be sent out to each station once with the destination (multicast)
* MAC address replaced by the station's MAC address. Note that this may
* break certain expectations of the receiver, e.g. the ability to drop
* unicast IP packets encapsulated in multicast L2 frames, or the ability
* to not send destination unreachable messages in such cases.
* This can only be toggled per BSS. Configure this on an interface of
* type %NL80211_IFTYPE_AP. It applies to all its VLAN interfaces
* (%NL80211_IFTYPE_AP_VLAN), except for those in 4addr (WDS) mode.
* If %NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED is not present with this
* command, the feature is disabled.
*
* @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial
* mesh config parameters may be given.
* @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the
@ -874,6 +888,12 @@
* This will contain a %NL80211_ATTR_NAN_MATCH nested attribute and
* %NL80211_ATTR_COOKIE.
*
* @NL80211_CMD_UPDATE_CONNECT_PARAMS: Update one or more connect parameters
* for subsequent roaming cases if the driver or firmware uses internal
* BSS selection. This command can be issued only while connected and it
* does not result in a change for the current association. Currently,
* only the %NL80211_ATTR_IE data is used and updated with this command.
*
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
*/
@ -1069,6 +1089,10 @@ enum nl80211_commands {
NL80211_CMD_CHANGE_NAN_CONFIG,
NL80211_CMD_NAN_MATCH,
NL80211_CMD_SET_MULTICAST_TO_UNICAST,
NL80211_CMD_UPDATE_CONNECT_PARAMS,
/* add new commands above here */
/* used to define NL80211_CMD_MAX below */
@ -1950,6 +1974,9 @@ enum nl80211_commands {
* Request/Response frame protection. This attribute contains the 16 octet
* STA Nonce followed by 16 octets of AP Nonce.
*
* @NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED: Indicates whether or not multicast
* packets should be send out as unicast to all stations (flag attribute).
*
* @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
@ -2352,6 +2379,8 @@ enum nl80211_attrs {
NL80211_ATTR_FILS_KEK,
NL80211_ATTR_FILS_NONCES,
NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED,
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,