Expire pending DB request for EAP-SIM/AKA/AKA'. Timeout defaults to 1
second and is user configurable in hostapd.conf (eap_sim_db_timeout).
Signed-off-by: Frederic Leroy <frederic.leroy@b-com.com>
This extends ieee80211_freq_to_channel_ext() with knowledge of the
operating classes for the 5 GHz channels 100..140.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Provide information on whether EAPOL-Key frame was sent successfully to
kernel for transmittion. wpa_eapol_key_send() will return
>= 0 on success and < 0 on failure. After receiving EAPOL-Key msg 3/4,
wpa_supplicant sends EAPOL-Key msg 4/4 and shows CTRL-EVENT-CONNECTED
only after verifying that the msg 4/4 was sent to kernel for
transmission successfully.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
When multiple interfaces across mutiple radios are started using a
single instance of hostapd, they all come up at different times
depending upon how long the ACS and HT scan take on each radio. This
will result in stations (that already have the AP profile) associating
with the first interfaces that comes up. For example in a dual band
radio case (2G and 5G) with ACS enabled, 2G always comes up first
because the ACS scan takes less time on 2G and this results in all
stations associating with the 2G interface first.
This feature brings up all the interfaces at the same time. The list of
interfaces specified via hostapd.conf files on the command line are all
marked as sync interfaces. All the interfaces are synchronized in
hostapd_setup_interface_complete().
This feature is turned on with '-S' commmand line option.
Signed-off-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Assign nl80211vendor commands QCA_NL80211_VENDOR_SUBCMD_OTA_TEST and
QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE as well as corresponding
attributes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
P2P device discovery can add peer entries based on a message directly
from a peer and from a Probe Response frame from a GO for all the P2P
Clients in the group. The former case for filtering out control
characters from the device name while the latter was not. Make this
consistent and filter both cases in the same way to avoid confusing
external programs using the device name of a P2P peer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no point in sending TPK M3 (TDLS Setup Confirm) with a failure
status if the first transmission attempt fails. Instead, just return a
failure by disabling the link rather than retransmitting the TPK M3
frame with an error status.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hmac_sha256_kdf() got pulled in only if CONFIG_ERP=y is set. Fix
test_sha256() by making the test case conditional on the function being
present.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_debug_reopen_file() used to write an error message at MSG_ERROR
level if it was called with last_path == NULL (the last debug log file
path not known). This is not a fatal error, but a normal case if
wpa_debug_open_file() has not been used. Remove the error message and
return success in such case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Linux packet socket workaround(*) has an impact in performance when the
workaround socket needs to be kept open to receive EAPOL frames. While
this is normally avoided with a kernel that has the issue addressed by
closing the workaround packet socket when detecting a frame through the
main socket, it is possible for that mechanism to not be sufficient,
e.g., when an open network connection (no EAPOL frames) is used.
Add a build option (CONFIG_NO_LINUX_PACKET_SOCKET_WAR=y) to disable the
workaround. This build option is disabled by default and can be enabled
explicitly on distributions which have an older kernel or a fix for the
kernel regression.
Also remove the unused variable num_rx.
(*) Linux kernel commit 576eb62598f10c8c7fd75703fe89010cdcfff596
('bridge: respect RFC2863 operational state') from 2012 introduced a
regression for using wpa_supplicant with EAPOL frames and a station
interface in a bridge.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
hmac_sha256() and hmac_sha256_vector() return a result code now, so use
that return value to terminate HMAC-SHA256-based GKDF/MIC similarly to
what was already done with the CMAC-based GKDF/MIC.
Signed-off-by: Jouni Malinen <j@w1.fi>
The recently added ProxyARP support (proxy_arp=1) in hostapd allows a
STA IPv4 address to be learned from DHCP or ARP messages. If that
information is available, add it to Account-Request messages in
Framed-IP-Address attribute.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter no_probe_resp_if_max_sta=1 can
be used to request hostapd not to reply to broadcast Probe Request
frames from unassociated STA if there is no room for additional stations
(max_num_sta). This can be used to discourage a STA from trying to
associate with this AP if the association would be rejected due to
maximum STA limit.
Signed-off-by: Jouni Malinen <j@w1.fi>
If hostapd or wpa_supplicant is built from a git repository, add a
VERSION_STR postfix from the current git branch state. This is from "git
describe --dirty=+". VERSION_STR will thus look something like
"2.6-devel-hostap_2_5-132-g4363c0d+" for development builds from a
modified repository.
This behavior is enabled automatically if a build within git repository
is detected (based on ../.git existing). This can be disabled with
CONFIG_NO_GITVER=y in wpa_supplicant/.config and hostapd/.config.
Signed-off-by: Jouni Malinen <j@w1.fi>
On TPK lifetime expiration, tear down the direct link before renewing
the link in the case of TDLS initiator processing. The expired key
cannot be used anymore, so it is better to explicitly tear down the old
link first.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This improves robustness of GO Negotiation in special cases where GO
Negotiation Request frames from the peer may end up getting delivered
multiple times, e.g., due to interference and retransmitted frames not
getting properly filtered out in duplicate detection (which is something
that number of drivers do not implement for pre-associated state).
If we have already replied with GO Negotiation Response frame with
Status 1 (not yet ready), do not reply to another GO Negotiation Request
frame from the peer if we have already received authorization from the
user (P2P_CONNECT command) for group formation and have sent out our GO
Negotiation Request frame. This avoids a possible sequence where two
independent GO Negotiation instances could go through in parallel if the
MAC address based rule on avoiding duplicate negotiations is not able to
prevent the case. This can allow GO Negotiation to complete successfully
whereas the previous behavior would have likely resulted in a failure
with neither device sending a GO Negotiation Confirm frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some drivers (like mac80211) do not accept changing the TX bitrate mask
before the network interface is up. Thus, calling
nl80211_disable_11b_rates() before the interface is up fails, and the
P2P network interface continues to use invalid bitrates.
To fix this call nl80211_disable_11b_rates() immediately after the
interface is brought up (and also after rfkill is unblocked).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
While testing, I noticed that printf_encode() makes control characters
human-readable, with one exemption, the DEL character (ASCII 127).
Assuming this exemption was unintentional, make it appear as an escaped
\x7f instead of a literal DEL character in the output.
Signed-off-by: Josh Lehan <krellan@krellan.net>
atheros_set_opt_ie() needs to be called before freeing drv->wpa_ie to
avoid hitting double-free on the deinit path. Similarly,
drv->wps_beacon_ie and drv->wps_probe_resp_ie could have been used after
being freed. Fix these be moving the atheros_set_opt_ie() call in
atheros_deinit().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for a driver to support sufficient number of channels to
hit the previous limit of 200 characters for the "nl80211: Scan included
frequencies:" debug message. Increase the maximum buffer length to 300
characters to allow more complete list of scanned frequencies to be
written into the debug log. This limit is more in line with the
MAX_REPORT_FREQS (50) limit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In addition to the PTK length increasing, the length of the PMK was
increased (from 256 to 384 bits) for the 00-0f-ac:12 AKM. This part was
missing from the initial implementation and a fixed length (256-bit) PMK
was used for all AKMs.
Fix this by adding more complete support for variable length PMK and use
384 bits from MSK instead of 256 bits when using this AKM. This is not
backwards compatible with the earlier implementations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previous implementation used an obsolete sm->eapol_key_crypt pointer
which was not set anywhere (i.e., was always NULL). In addition, the
condition of sm->eap_if->eapKeyAvailable was not valid here since this
is the case of MSK from an external authentication server and not the
internal EAP server. Consequently, the wpa_auth_pmksa_add() call here
was never used.
The PMKSA cache was still added, but it happened at the completion of
the 4-way handshake rather than at the completion of EAP authentication.
That later location looks better, so delete the unreachable code in
Access-Accept handling. In addition, remove the now complete unused
struct eapol_state_machine eapol_key_* variables.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
With driver wrappers that implement set_privacy(), set_generic_elem(),
set_ieee8021x(), or set_ap_wps_ie(), it was possible to hit a NULL
pointer dereference in error cases where interface setup failed and
the network configuration used WPA/WPA2, IEEE 802.1X, or WPS.
Fix this by skipping the driver operations in case the driver interface
is not initialized.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Don't add unnecessary P2PS follow-on PD Request attributes when
the request status is not P2P_SC_SUCCESS_DEFERRED.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
In P2PS PD Request processing in some error case scenarios, such as
verification of the WPS config method, the flow aborts before saving
mandatory P2PS PD Request attributes. This in turn causes the control
interface notification events to be sent with invalid parameters.
Fix this by changing the order of verification and processing steps of
the PD Request message handling.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
On successful P2P PD, report the chosen frequency in case the local
device is going to be the P2P GO, so in can later be used to instantiate
the new P2P GO, etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
In case the P2PS PD Response includes the P2P Channel List attribute,
update the peer device supported channels and verify that the local
device has common channels with the peer (only a sanity check).
If the Operating Channel attribute is included in the response, check
that it is included in the intersection and store it as the peer's
operating frequency (so it could later be used in the join flow, etc.).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
In case the P2PS PD Request includes the P2P Channel List attribute,
update the peer device supported channels and check if we have common
channels with the peer that can be used for the connection establishment
based on the connection capabilities:
1. In case of P2PS PD Request with no common channels, defer
the flow unless auto accept equals true and the connection
capabilities equals NEW (in which case the channels would be
negotiated in the GO Negotiation).
2. In case of Follow up P2PS PD Request with no common channels,
reject the request unless the connection capability is NEW.
In addition, in case of a successful P2PS PD, save the device
operating frequency (so it can be later used for join flow, etc.).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add operating channel selection and channel list processing similar to
that done when building GO Negotiation Request, i.e., consider the
currently used channels, configured channels, etc.
P2PS introduces a flow where a responder needs to provide channel data
without being previously aware of the current constraints, i.e., the
channels currently in use by other interfaces. To handle this, extend
the get_group_capability() callback to also handle channel selection
aspects of group capabilities.
In case there is an active P2P GO that is going to be used for the P2PS
PD, force its current operating frequency in the PD attributes.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
If a Provision Discovery Request is received for an unknown peer, a new
device entry is being added, but the flow continues without updating the
local p2p_device pointer, requiring to check the pointer value before
every access.
1. Change this, so once a device is added, the flow updates the local
p2p_device pointer and avoids the checks later in the flow.
2. If the device is not known even after adding it, skip the processing,
send the PD Response, and return.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
It is possible that p2p_build_prov_disc_resp() is called with a NULL
device entry, which might be dereferenced when calling
p2p->cfg->get_persistent_group() for the P2PS with persistent group
case. Fix this by checking the device pointer before accessing it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Write a text version of the content type and handshake type in debug log
to make it easier to follow TLS exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
The utf8_string_len comparison was off by one and ended up accepting a
truncated three-byte encoded UTF-8 character at the end of the string if
the octet was missing. Since the password string gets null terminated in
the configuration, this did not result in reading beyond the buffer, but
anyway, it is better to explicitly reject the string rather than try to
use an incorrectly encoded UTF-8 string as the password.
Signed-off-by: Jouni Malinen <j@w1.fi>
BoringSSL has removed the OpenSSL OCSP implementation (OCSP_*()
functions) and instead, provides only a minimal mechanism for include
the status request extension and fetching the response from the server.
As such, the previous OpenSSL-based implementation for OCSP stapling is
not usable with BoringSSL.
Add a new implementation that uses BoringSSL to request and fetch the
OCSP stapling response and then parse and validate this with the new
implementation within wpa_supplicant. While this may not have identical
behavior with the OpenSSL-based implementation, this should be a good
starting point for being able to use OCSP stapling with BoringSSL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Validate that all the required attributes appear in a P2PS PD Request,
and in addition, in the case of follow-on PD Request, check that the
given values match those of the original PD Request.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a follow-on PD request is received, peer should not send a
follow-on PD response except the case when the PD request status value
is 12 (Success: accepted by user). Previously, the wpa_supplicant
implementation behaved differently sending the follow-on PD Response on
any follow-on PD Request.
Fix the issue by adding the following changes:
1. Don't send PD Response if the follow-on PD Request status is
different than 12 (seeker side).
2. Don't wait for the follow-on PD Response if the follow-on PD
Request was sent with the status different than 12 (advertiser
side).
3. If the follow-on PD Request was sent with the status different
than 12 use the follow-on PD Request ACK as PD completion event
(advertiser side).
4. Notify ASP about the PD completion by sending P2PS-PROV-DONE with
the PD Request status (advertiser side).
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
It is expected that p2p_flush() should stop any ongoing p2p operation.
However, this was not the case with extended listen which was not
cancelled on p2p_flush() flows. Fix this, by cancelling the extended
listen in p2p_flush().
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The new hostapd configuration parameter anqp_elem can now be used to
configure arbitrary ANQP-elements for the GAS/ANQP server. In addition
to supporting new elements, this can be used to override previously
supported elements if some special values are needed (mainly for testing
purposes).
The parameter uses following format:
anqp_elem=<InfoID>:<hexdump of payload>
For example, AP Geospatial Location ANQP-element with unknown location:
anqp_elem=265:0000
and AP Civic Location ANQP-element with unknown location:
anqp_elem=266:000000
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The switch to BoringSSL broke keystore-backed keys because
wpa_supplicant was using the dynamic ENGINE loading to load
the keystore module.
The ENGINE-like functionality in BoringSSL is much simpler
and this change should enable it.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Some devices cannot respond to inactive client probe (empty data frame)
within one second. For example, iPhone may take up to 3 secs. This
becomes a significant problem when ap_max_inactivity is set to lower
value such as 10 secs. iPhone can lose Wi-Fi connection after ~1 min
of user inactivity.
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
On RADIUS auth/acct failures hostapd will try a new server if one is
available. Reuse the failover logic to force a socket renewal if only
one RADIUS server is configured.
This fixes problems when a route for the RADIUS server gets added after
the socket was "connected". The RADIUS socket is still sending the
RADIUS requests out using the previous route.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
IEEE Std 802.11-2012 13.3.1 states that the AID should be generated on
the local node for each peer. Previously, we were using the peer link ID
(generated by the peer) which may not be unique among all peers. Correct
this by reusing the AP AID generation code.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Commit d66dcb0d0b ('WEP: Remove VLAN
support from hostapd') already removed VLAN support for WEP encryption,
so vlan_setup_encryption_dyn() is no longer needed.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This ensures that group key is set as long as the interface exists.
Additionally, ifconfig_up is needed as wpa_group will enter
FATAL_FAILURE if the interface is still down. Also vlan_remove_dynamic()
is moved after wpa_auth_sta_deinit() so vlan_remove_dynamic() can check
it was the last user of the wpa_group.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Some APs don't include a CSA IE when an ECSA IE is generated,
and mac80211 used to fail following their channel switch. Add
a testing option to hostapd to allow reproducing the behavior.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix and extend the ieee80211_freq_to_channel_ext() function to deal
correctly with VHT operating classes (128, 129, 130).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The CSA channel and operating class values need to be set for all types
of channel switch (i.e., either if it's triggered by the control
interfaces or due to the GO-follows-STA flow). To do so, move the code
that sets them from the GO-follows-STA flow to the more generic
hostapd_fill_csa_settings() function.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
The hostapd_hw_get_channel() function can't be used to convert center
frequencies to channel numbers, because the hw mode lists don't have all
the center frequencies. The hw mode lists have the main channel
frequencies and flags to indicate the channel topography.
For instance, channel 5805 with VHT80- has the channel center frequency
segment 0 at 5775. This segment is only indicated indirectly in the hw
mode list by the HOSTAPD_CHAN_VHT_50_30 flag. The hw mode list doesn't
have any elements with frequency 5775 to allow the conversion to a
channel number. Thus, we need to use ieee80211_freq_to_chan() instead.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Pass to the driver a list of CSA counter offsets when sending Probe
Response frames during a CSA period. This allows the kernel to correctly
update the CSA/eCSA elements.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Some management frames contain CSA counters which should be updated by
kernel. Change driver op send_mlme() allowing to send a frame,
specifying an array of offsets to the CSA counters which should be
updated. For example, CSA offsets parameters should be specified when
sending Probe Response frames during CSA period.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Advertise current operating class in Beacon and Probe Response frames.
This Supported Operating Classes element is required by the standard
when extended channel switch is supported. However, since this element
doesn't reflect correctly the sub-band spectrum breakdown and can't be
effectively used by clients, publish only the minimal required part
which is the current operating class.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Fix the order of CSA, eCSA, Secondary Channel Offset, and Wide Bandwidth
Channel Switch Wrapper elements in Beacon and Probe Response frames.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add new GO frequency move policy. The P2P_GO_FREQ_MOVE_SCM_ECSA prefers
SCM if all the clients advertise eCSA support and the candidate
frequency is one of the group common frequencies.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Extended channel switch provides an ability to switch between operating
classes and is required for P2P Devices by the P2P specification when
switching in 5 GHz.
When the operating class is provided for channel switch, the AP/P2P GO
will use eCSA IE in addition to the regular CSA IE both on 2.4 GHz and 5
GHz bands.
Transitions between different hw_modes are not supported.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Channel switch may be performed using both CSA and eCSA IEs together.
This may happen, for example with a P2P GO on band A with legacy
clients. Extend driver API to support up to 2 CSA counters.
This patch also includes the required implementation for nl80211.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When building Beacon and Probe Response frames for the target channel,
consider bandwidth parameter for VHT channels. In addition, add support
for updating vht_oper_centr_freq_seg0_idx and
vht_oper_centr_freq_seg1_idx.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When switching to a VHT channel with width greater than 20 MHz, add Wide
Bandwidth Channel Switch element. This element is added in Beacon and
Probe Response frames inside Channel Switch Wrapper element.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When CSA is started, hostapd_change_config_freq() computes the channel
from the provided frequency. Use this stored channel to add CSA IE in
Beacon frames, instead of recomputing the channel each time.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
All the other web_connection_parse_*() functions were already doing
this, so make the GET handler consistent as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 7d711541dc ('Clear TK part of PTK
after driver key configuration') started clearing TK from memory
immediately after having configured it to the driver when processing
EAPOL-Key message 3/4. While this covered the most common case, it did
not take into account the possibility of the authenticator having to
retry EAPOL-Key message 3/4 in case the first EAPOL-Key message 4/4
response is lost. That case ended up trying to reinstall the same TK to
the driver, but the key was not available anymore.
Fix the EAPOL-Key message 3/4 retry case by configuring TK to the driver
only once. There was no need to try to set the same key after each
EAPOL-Key message 3/4 since TK could not change. If actual PTK rekeying
is used, the new TK will be configured once when processing the new
EAPOL-Key message 3/4 for the first time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the binary sizes to be reduced if no support for nl80211
vendor extensions are needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow wpa_supplicant to use vendor scan (if supported by the driver)
together with the normal nl80211 scan and handling external scan events.
Since this results in possibility of concurrent scan operations, some of
the operations related to scan results need to check more carefully when
an event is relevant for a specific interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit contains the necessary changes for supporting the QCA vendor
scan implementation, i.e., sending the vendor scan command to underlying
driver and handling the vendor scan events from the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Introduce definitions for QCA vendor specific subcommands
and attributes to support vendor scan request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes an issue where hostapd SET command is used to configure RSN
parameters and the wpa parameter is sent after the other parameters.
Previously, the default case here ended up clearing rsn_pairwise and
wpa_pairwise values and once wpa=2 was finally set, the cipher
configuration had already been lost.
Signed-off-by: Jouni Malinen <j@w1.fi>
Split chown() call in wpa_ctrl_open() and wpa_ctrl_open2() to allow the
group id to be set even if the process does not have privileges to
change the owner. This is needed for modules that need to communicate
with wpa_supplicant since without the group change, wpa_supplicant may
not have privileges to send the response to a control interface command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, station's VHT information elements were copied and passed
regardless of the AP's VHT configuration. As a result, AP with VHT
disabled in configuration could have ended up transmitting packets in
VHT rates though AP is not advertising VHT support. Fix this by copying
the station's VHT capabilities only when AP supports VHT (both hardware
and configuration).
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
The GTK value received in RSN (WPA2) group rekeying did not use the
wpa_hexdump_key() version of debug printing that is conditional on -K
being included on the command line.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use shorter variables for storing the attribute lengths and group these
variables together to allow compiler to pack them more efficiently. This
reduces the struct size from 960 bytes to 760 bytes in 64-bit builds.
This reduces stack use in number of functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to maintain two concurrent instances of struct
wps_parse_attr in this function. Share a single structure for parsing
both IEs.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reset hapd->num_probereq_cb to 0 on an interface deinit to avoid
unexpected behavior if the same interface is enabled again without fully
freeing the data structures. hostapd_register_probereq_cb() increments
hapd->num_probereq_cb by one and leaves all old values unchanged. In
this deinit+init case, that would result in the first entry in the list
having an uninitialized pointer and the next Probe Request frame
processing would likely cause the process to terminate on segmentation
fault.
This issue could be hit when hostapd was used with WPS enabled (non-zero
wps_state configuration parameter) and control interface command DISABLE
and ENABLE were used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to allow new operation to be started after an error
without having to wait for the AP entry to time out.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_supplicant_parse_ies() was never supposed to be used as a generic IE
parser, i.e., it is for the specific purpose of parsing EAPOL-Key Key
Data IEs and KDEs. TDLS used this function for parsing generic AP IEs
and while that works, it resulted in confusing "WPA: Unrecognized
EAPOL-Key Key Data IE" debug messages. Clean this up by using
ieee802_11_parse_elems() for the cases where generic IEs are being
parsed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the previous tracking design to add a station entry based
on other management frames than Probe Request frames. For example, this
covers a case where the station is using passive scanning.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new no_auth_if_seen_on=<ifname> parameter can now be used to
configure hostapd to reject authentication from a station that was seen
on another radio.
This can be used with enabled track_sta_max_num configuration on another
interface controlled by the same hostapd process to reject
authentication attempts from a station that has been detected to be
capable of operating on another band, e.g., to try to reduce likelihood
of the station selecting a 2.4 GHz BSS when the AP operates both a 2.4
GHz and 5 GHz BSS concurrently.
Note: Enabling this can cause connectivity issues and increase latency for
connecting with the AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows control interface monitors to get more detailed information
in cases where wpa_supplicant-based SME receives an Authentication frame
with non-zero status code.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new no_probe_resp_if_seen_on=<ifname> parameter can now be used to
configure hostapd to not reply to group-addressed Probe Request from a
station that was seen on another radio.
This can be used with enabled track_sta_max_num configuration on another
interface controlled by the same hostapd process to restrict Probe
Request frame handling from replying to group-addressed Probe Request
frames from a station that has been detected to be capable of operating
on another band, e.g., to try to reduce likelihood of the station
selecting a 2.4 GHz BSS when the AP operates both a 2.4 GHz and 5 GHz
BSS concurrently.
Note: Enabling this can cause connectivity issues and increase latency
for discovering the AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd can now be configured to track unconnected stations based on
Probe Request frames seen from them. This can be used, e.g., to detect
dualband capable station before they have associated. Such information
could then be used to provide guidance on which colocated BSS to use in
case of a dualband AP that operates concurrently on multiple bands under
the control of a single hostapd process.
Signed-off-by: Jouni Malinen <j@w1.fi>
For now, there is no support for passing extended_capa pointers through
the driver_privsep.c interface from wpa_priv. Avoid leaving bogus
pointers by explicitly clearing these on both wpa_priv and
wpa_supplicant sides.
Signed-off-by: Jouni Malinen <j@w1.fi>
DSSS/CCK rate support in 40 MHz has to be set to 0 for 5 GHz band since
this mechanism is designed only for the 2.4 GHz band. Clear
HT_CAP_INFO_DSSS_CCK40MHZ in ht_capab when the configured mode is
neither 11b nor 11g.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
This adds a new helper function wpa_ctrl_open2() that can be used
instead of wpa_ctrl_open() to override the default client socket
directory. Add optional -s<directory path> argument to hostapd_cli and
wpa_cli to allow the client socket directory to be specified.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
No need to have a common failure handler if it is used from only a
single location and that lcoation does not even need the memory freeing
step.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the EAP-WSC peer state machine ended up just ignoring an
error and waiting for a new message from the AP. This is not going to
recover the exchange, so simply force the connection to terminate
immediately.
Signed-off-by: Jouni Malinen <j@w1.fi>
The hbp pointer is moved to the next space already earlier in this code
path, so the while loop here did not really do anything.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for wpa_auth_sm_event(WPA_DEAUTH) to be called from
wpa_sm_step() iteration in the case the EAPOL authenticator state
machine ended up requesting the station to be disconnected. This
resulted in unnecessary recursive call to wpa_sm_step(). Avoid this by
using the already running call to process the state change.
It was possible to hit this sequence in the hwsim test case
ap_wpa2_eap_eke_server_oom.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Clearing keyRun here is not specified in IEEE Std 802.1X-2004, but it
looks like this would be logical thing to do here since the EAPOL-Key
exchange is not possible in this state. It is possible to get here on
disconnection event without advancing to the AUTHENTICATING state to
clear keyRun before the IEEE 802.11 RSN authenticator state machine runs
and that may advance from AUTHENTICATION2 to INITPMK if keyRun = TRUE
has been left from the last association. This can be avoided by clearing
keyRun here.
It was possible to hit this corner case in the hwsim test case
ap_wpa2_eap_eke_server_oom in the case getKey operation was forced to
fail memory allocation. The following association resulted in the
station getting disconnected when entering INITPMK without going through
EAP authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows an empty nested list (i.e., no MAC addresses) to be included
in the NL80211_CMD_SET_MAC_ACL message unlike with
nla_nest_start()/nla_nest_end() where the current libnl implementation
removes the "empty" attribute and causes cfg80211 to reject the command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While the EAPOL-Key MIC derivation was already changed from SHA256 to
SHA384 for the Suite B 192-bit AKM, KDF had not been updated similarly.
Fix this by using HMAC-SHA384 instead of HMAC-SHA256 when deriving PTK
from PMK when using the Suite B 192-bit AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
Config file is written to a temp file and then it is renamed to the
original config file. However, it is possible that the rename operation
will be commited to storage while file data will be still in cache
causing original config file to be empty or partially written in case of
a system reboot without a clean shutdown. Make this less likely to occur
by forcing the data to be written to the storage device before renaming
the file.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Commit 7da4f4b499 ('WPS: Check maximum
HTTP body length earlier in the process') added too strict check for
body length allocation. The comparison of new_alloc_nbytes against
h->max_bytes did not take into account that HTTPREAD_BODYBUF_DELTA was
added to previous allocation even if that ended up going beyond
h->max_bytes. This ended up rejecting some valid HTTP operations, e.g.,
when checking AP response to WPS ER setting selected registrar.
Fix this by taking HTTPREAD_BODYBUF_DELTA into account.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit de2a7b796d ('OpenSSL: Use
connection certificate chain with PKCS#12 extra certs') added a new
mechanism for doing this with OpenSSL 1.0.2 and newer. However, it did
not poinr out anything in debug log if SSL_add1_chain_cert() failed. Add
such a debug print and also silence static analyzer warning on res being
stored without being read (since the error case is ignored at least for
now).
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to limit TLS session resumption within a TLS library
implementation to apply only for the cases where the same EAP method is
used. While the EAP server method matching will be enforced separately
by EAP server method implementations, this additional steps can optimize
cases by falling back to full authentication instead of having to reject
attempts after having completed session resumption successfully.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new tls_connection_set_success_data(),
tls_connection_set_success_data_resumed(),
tls_connection_get_success_data(), and tls_connection_remove_session()
functions can be used to mark cached sessions valid and to remove
invalid cached sessions. This commit is only adding empty functions. The
actual functionality will be implemented in followup commits.
Signed-off-by: Jouni Malinen <j@w1.fi>
This new hostapd configuration parameter can be used to enable TLS
session resumption. This commit adds the configuration parameter through
the configuration system and RADIUS/EAPOL/EAP server components. The
actual changes to enable session caching will be addressed in followup
commits.
Signed-off-by: Jouni Malinen <j@w1.fi>
The EAP server is not yet capable of using TLS session ticket to resume
a session. Explicitly disable use of TLS session ticket with
EAP-TLS/TTLS/PEAP to avoid wasting resources on generating a session
ticket that cannot be used for anything.
Signed-off-by: Jouni Malinen <j@w1.fi>
BoringSSL does not support 192-bit AES, so these parts of the
wpa_supplicant module tests would fail.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed at least with BoringSSL to avoid accepting OCSP-required
configuration with a TLS library that does not support OCSP stapling.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Unlike OpenSSL PKCS12_parse(), the BoringSSL version seems to require
the password pointer to be non-NULL even if no password is present. Map
passwrd == NULL to passwd = "" to avoid a NULL pointer dereference
within BoringSSL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
BoringSSL commit 533ef7304d9b48aad38805f1997031a0a034d7fe ('Remove
SSL_clear calls in handshake functions.') triggered a regression for
EAP-TLS/TTLS/PEAP session resumption in wpa_supplicant due to the
removed SSL_clear() call in ssl3_connect() going away and wpa_supplicant
not calling SSL_clear() after SSL_shutdown(). Fix this by adding the
SSL_clear() call into wpa_supplicant after SSL_shutdown() when preparing
the ssl instance for another connection.
While OpenSSL is still call SSL_clear() in ssl3_connect(), it looks to
be safe to add this call to wpa_supplicant unconditionally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This function does not seem to be available in BoringSSL. Since it is
needed for EAP-FAST (which is not currently working with BoringSSL),
address this by commenting out the EAP-FAST specific step from builds
that do not include EAP-FAST support.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like BoringSSL does include that function even though it claims
support for OPENSSL_VERSION_NUMBER where this is available (1.0.2). For
now, comment out that call to fix build.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like BoringSSL has removed the AES_wrap_key(), AES_unwrap_key()
API. This broke wpa_supplicant/hostapd build since those functions from
OpenSSL were used to replace the internal AES key wrap implementation.
Add a new build configuration option
(CONFIG_OPENSSL_INTERNAL_AES_WRAP=y) to allow the internal
implementation to be used with CONFIG_OPENSSL=y build to allow build
against the latest BoringSSL version.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 6959145b86 ('FST: Integration into
hostapd') introduced this duplicated call due to an incorrect merge
conflict resolution in ap_sta_set_authorized(). An earlier commit
61fc90483f ('P2P: Handle improper WPS
termination on GO during group formation') had moved this call to an
earlier location in the function and there is no point in re-introducing
another copy of the call at the end of the function.
Signed-off-by: Jouni Malinen <j@w1.fi>
Couple of the for-each-interface loops used incorrect return value when
skipping over non-WPS interfaces. This could result in skipping some WPS
interfaces in the loop and returning error. Setting AP PIN did not check
for WPS being enabled at all and trigger a NULL pointer dereference if
non-WPS interface was enabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
Incorrect number of bytes was skipped from the beginning of the line
which resulted in the loop skipping spaces doing nothing. However, the
following operation was simply looking for the max-age parameter with
os_strstr(), so this did not have any effect on functionality. Fix the
number of bytes to skip and remove the unneeded loop to skip spaces.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the Hotspot 2.0 case of OSU user interaction to fail
with wpadebug browser due to permission denial in the "start" command
("java.lang.SecurityException: Permission Denial: startActivity asks to
run as user -2 but is calling from user 0; this requires
android.permission.INTERACT_ACROSS_USERS_FULL"). Avoid this by using
more flexible USER_CURRENT_OR_SELF (-3) value with the --user argument.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
cfg80211 sends TSF information with the attribute NL80211_BSS_BEACON_TSF
if the scan results include information from Beacon frame. Probe
Response frame information is included in NL80211_BSS_TSF. If the device
receives only Beacon frames, NL80211_BSS_TSF might not carry updated
TSF, which results an older TSF being used in wpa_supplicant. Fetch both
possible TSF values (if available) and choose the latest TSF for the BSS
entry.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When using P2P invitation to re-invoke a persistent P2P group without
specifying the operating channel, query the driver for the preferred
frequency list, and use it to select the operating channel of the group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When using OpenSSL 1.0.2 or newer, this replaces the older
SSL_CTX_add_extra_chain_cert() design with SSL_add1_chain_cert() to keep
the extra chain certificates out from SSL_CTX and specific to each
connection. In addition, build and rearrange extra certificates with
SSL_build_cert_chain() to avoid incorrect certificates and incorrect
order of certificates in the TLS handshake.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the possible extra certificate(s) from a PKCS#12 file was
added once for each authentication attempt. This resulted in OpenSSL
concatenating the certificates multiple time (add one copy for each try
during the wpa_supplicant process lifetime). Fix this by clearing the
extra chain certificates before adding new ones when using OpenSSL 1.0.1
or newer that include the needed function.
Signed-off-by: Jouni Malinen <j@w1.fi>
This code path could not be hit with the RSNE generated by hostapd or
wpa_supplicant, but it is now possible to reach when using
own_ie_override test functionality. The RSNE and IE buffer length were
not updated correct in case wpa_insert_pmkid() had to add the RSN
Capabilities field.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the new own_ie_override=<hexdump> configuration parameter to
be used to replace the normally generated WPA/RSN IE(s) for testing
purposes in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <j@w1.fi>
The PMKIDCount, PMKID List, and Group Management Cipher Suite fields are
optional to include in the RSNE in cases where these would not have
values that are different from the default values. In practice,
PMKIDCount is always 0 in Beacon and Probe Response frames, so the only
field of these that could have a non-default value is Group Management
Cipher Suite. When BIP is used, that field is not needed either due to
BIP being the default cipher when PMF is enabled.
Remove these fields from RSNE when BIP is used to save six octets in
Beacon and Probe Response frames. In addition to reduced frame length,
this is a workaround for interoperability issues with iOS 8.4 in cases
where FT and PMF are enabled. iOS seems to be rejecting EAPOL-Key msg
3/4 during FT initial mobility domain association if the RSNE includes
the PMKIDCount field.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is similar to the earlier commit
b363121a20 ('WPS: Reject invalid
credential more cleanly'), but for the AP cases where AP settings are
being replaced. Previously, the new settings were taken into use even if
the invalid PSK/passphrase had to be removed. Now, the settings are
rejected with such an invalid configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use NULL to indicate if the address is not available instead of fixed
00:00:00:00:00:00. wpas_p2ps_prov_complete() already had code for
converting NULL to that all zeros address for event messages.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Change P2PS P2P-PROV-SHOW-PIN/P2P-PROV-ENTER-PIN event notifications
on PD Request/Response handling to meet required P2PS behavior.
The new implemented scheme:
1. For a legacy P2P provision discovery the event behavior remains
without changes
2. P2PS PD, advertiser method: DISPLAY, autoaccept: TRUE:
Advertiser: SHOW-PIN on PD request replied with a status SUCCESS
Seeker: ENTER-PIN on PD response received with a status SUCCESS
3. P2PS PD, advertiser method: DISPLAY, autoaccept: FALSE:
Advertiser: SHOW-PIN on PD request replied with a status
INFO_CURRENTLY_UNAVAILABLE
Seeker: ENTER-PIN on Follow-on PD request with a status
SUCCESS_DEFERRED
4. P2PS PD, advertiser method: KEYPAD, autoaccept: TRUE/FALSE:
Advertiser: ENTER-PIN on PD request replied with a status
INFO_CURRENTLY_UNAVAILABLE
Seeker: SHOW-PIN on PD response received with a status
INFO_CURRENTLY_UNAVAILABLE
This change in behavior breaks the existing test cases
p2ps_connect_keypad_method_nonautoaccept and
p2ps_connect_display_method_nonautoaccept. Those will be fixed in a
followup commit.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add a function to compute the group common frequencies, and
use it to update the group_common_frequencies as part of the
channel switch flows.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add ieee80211_freq_to_channel_ext() conversion function into
ieee802_11_common.c. This function converts freq to channel and
additionally computes operating class, based on provided HT and VHT
parameters.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This makes it possible to use these helper functions from hostapd as
well as the current use in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This buffer is owned by the FST module, so mark it const in the
set_ies() callback to make it clearer which component is responsible for
modifying and freeing this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes an issue where freed MB IEs buffer memory could potentially
have been accessed after an interface is detached from FST group.
Without this fix, if an interface is detached from FST group, it can use
MB IEs buffer previously set by fst_iface_set_ies(), although the buffer
was released by fst_iface_delete().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The mesh SAE auth often fails with master branch. By bisect I found
commit eb5fee0bf5 ('SAE: Add side-channel
protection to PWE derivation with ECC') causes this issue. This does not
mean the commit has a bug. This is just a CPU resource issue.
After the commit, sae_derive_pwe_ecc() spends 101(msec) on my PC (Intel
Atom N270 1.6GHz). But dot11RSNASAERetransPeriod is 40(msec). So
auth_sae_retransmit_timer() is always called and it can causes
continuous frame exchanges. Before the commit, it was 23(msec).
On the IEEE 802.11 spec, the default value of dot11RSNASAERetransPeriod
is defined as 40(msec). But it looks short because generally mesh
functionality will be used on low spec devices. Indeed Raspberry Pi B+
(ARM ARM1176JZF-S 700MHz) requires 287(msec) for new
sae_derive_pwe_ecc().
So this patch makes the default to 1000(msec) and makes it configurable.
This issue does not occur on infrastructure SAE because the
dot11RSNASAERetransPeriod is not used on it.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The new CONFIG_NO_RC4=y build option can be used to remove all internal
hostapd and wpa_supplicant uses of RC4. It should be noted that external
uses (e.g., within a TLS library) do not get disabled when doing this.
This removes capability of supporting WPA/TKIP, dynamic WEP keys with
IEEE 802.1X, WEP shared key authentication, and MSCHAPv2 password
changes.
Signed-off-by: Jouni Malinen <j@w1.fi>
FIPS_mode_set(1) cannot be called multiple times which could happen in
some dynamic interface cases. Avoid this by enabling FIPS mode only
once. There is no code in wpa_supplicant to disable FIPS mode, so once
it is enabled, it will remain enabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
MD4 is not allowed in such builds, so comment out md4_vector() from the
build to force compile time failures for cases that cannot be supported
instead of failing the MD¤ operations at runtime. This makes it easier
to detect and fix accidental cases where MD4 could still be used in some
older protocols.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 94f1fe6f63 ('Remove master key
extraction from tls_connection_get_keys()') left only fetching of
server/client random, but did not rename the function and structure to
minimize code changes. The only name is quite confusing, so rename this
through the repository to match the new purpose.
Signed-off-by: Jouni Malinen <j@w1.fi>
tls_connection_get_keys() used to return TLS master secret, but that
part was removed in commit 94f1fe6f63
('Remove master key extraction from tls_connection_get_keys()'). Since
then, there is no real need for preventing this function from being used
in FIPS mode.
Signed-off-by: Jouni Malinen <j@w1.fi>
The bytes pointer was not reset back to the beginning of the buffer when
mixing in additional entropy from the crypto module. This resulted in
writing beyond the return buffer and not getting the required mixing of
the extra entropy for the actual return buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like the compiler version used in Android 5.0 warns about
potentially uninitialized oper_freq variable in these debug messages.
That is not really valid since this code path can be reached only if
found != 0 and in such a case, oper_freq is set. Anyway, it seems better
to avoid compiler warnings, so add an unnecessary initialization for
oper_freq for now.
Signed-off-by: Jouni Malinen <j@w1.fi>
MD5 is not allowed in such builds, so comment out md5_vector() from the
build to force compile time failures for cases that cannot be supported
instead of failing the MD5 operations at runtime. This makes it easier
to detect and fix accidental cases where MD5 could still be used in some
older protocols.
Signed-off-by: Jouni Malinen <j@w1.fi>
FIPS builds do not include support for MD4/MD5, so disable
EAP-TTLS/CHAP, MSCHAP, and MSCHAPV2 when CONFIG_FIPS=y is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
MD5 is not available in CONFIG_FIPS=y builds, so use SHA1 for the EAP
peer workaround that tries to detect more robustly whether a duplicate
message was sent.
Signed-off-by: Jouni Malinen <j@w1.fi>
The OpenSSL internal AES_wrap_key() and AES_unwrap_key() functions are
unfortunately not available in FIPS mode. Trying to use them results in
"aes_misc.c(83): OpenSSL internal error, assertion failed: Low level API
call to cipher AES forbidden in FIPS mode!" and process termination.
Work around this by reverting commit
f19c907822 ('OpenSSL: Implement aes_wrap()
and aes_unwrap()') changes for CONFIG_FIPS=y case. In practice, this
ends up using the internal AES key wrap/unwrap implementation through
the OpenSSL EVP API which is available in FIPS mode. When CONFIG_FIPS=y
is not used, the OpenSSL AES_wrap_key()/AES_unwrap_key() API continues
to be used to minimize code size.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids a call to hmac_md5() to fix the build. The EAPOL-Key frame
TX code is not applicable for any FIPS mode operation, so the simplest
approach is to remove this from the build.
Signed-off-by: Jouni Malinen <j@w1.fi>
When processing a GO Negotiation Request and Response, if local driver
supports the preferred channel list extension, then:
- Check if peer's preference for operating channel is already included
in our preferred channel list and if so, take the oper_channel as is.
- If peer's preference for operating channel is not in local device's
preferred channel list and peer device has provided its preferred
frequency list in the GO Negotiation Request/Response, then find a
channel that is common for both preferred channel lists and use it
for oper_channel.
- If peer's preference for operating channel is not in local device's
preferred channel list and peer device doesn't use preferred channel
list extension, i.e., no preferred channel list in GO Negotiation
Request/Response, then look for a channel that is common for local
device's preferred channel list and peer's list of supported channels
and use it for oper_channel.
- In case no common channel is found, use the peer's preference for
oper_channel as is.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a callback function that can be used from the P2P module to
request the current preferred list of operating channels from the
driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add an extra condition to omit operating channel preference when
building GO Negotiation Response. If the local device supports the
preferred frequency list extension, then when sending a GO Negotiation
Response frame, advertise the preferred operating channel unless local
device is assuming the P2P Client role and has an empty preferred
frequency list, in which case local device can omit its preference for
the operating channel.
This change helps make use of the preferred frequency list and the
calculated best channel for both negotiating parties of the P2P
connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When sending a GO Negotiation Request, advertise the preferred frequency
list in a new vendor specific IE. This can be used to extend the
standard P2P behavior where a single preferred channel can be advertised
by allowing a priority list of channels to be indicated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver supports the preferred frequency list extension, use this
information from the driver when no explicitly configured preference
list (p2p_pref_chan) is present for P2P operating channel selection.
This commit adds this for GO Negotiation and Invitation use cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds parsing of QCA vendor specific elements and as the first such
element to be parsed, stores pointers to the preferred frequency list
element that can be used to enhance P2P channel negotiation behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new enum qca_vendor_element_id registry is used to manage
assignments of vendor specific elements using the QCA OUI 00:13:74. The
initial assignment is for the purpose for extending P2P functionality
for cases where the wpa_supplicant implementation is used by both ends
of an exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the QCA vendor specific nl80211 interface to query the preferred
frequency list from driver and add a new wpa_cli command to query this
information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Upon GO Negotiation completion, if the remote peer becomes GO, send a
hint event over QCA vendor specific interface to inform the driver of
the likely operating channel of the P2P GO.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the nl80211 interface command "driver status" to retrieve the
concurrency capabilities from the driver using the QCA vendor
extensions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When ACS is offloaded to device driver and the hw_mode parameter is set
to any, the current_mode structure is NULL which fails the ACS command.
Fix this by populating the ACS channel list with channels from all bands
when current_mode is NULL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add vendor command to pass SET setband command to the driver and read
the updated channel list from driver when this notification succeeds.
This allows the driver to update its internal channel lists based on
setband configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The issue with the special form of TLS session tickets has been fixed in
the OpenSSL 1.1.0 branch, so disable workaround for it. OpenSSL 1.0.1
and 1.0.2 workaround is still in place until a release with the fix has
been made.
This allows TLSv1.1 and TLSv1.2 to be negotiated for EAP-FAST with the
OpenSSL versions that support this.
Signed-off-by: Jouni Malinen <j@w1.fi>
If there is only zero-length buffer of output data in error case, mark
that as an immediate failure instead of trying to report that
non-existing error report to the server. This allows faster connection
termination in cases where a non-recoverable error occurs in local TLS
processing, e.g., if none of the configured ciphers are available.
Signed-off-by: Jouni Malinen <j@w1.fi>
EAP-TLS was already doing this, but the other TLS-based EAP methods did
not mark methodState DONE and decision FAIL on local TLS processing
errors (instead, they left the connection waiting for a longer timeout).
Signed-off-by: Jouni Malinen <j@w1.fi>
OpenSSL 1.1.0 disables the anonymous ciphers by default, so need to
enable these for the special case of anonymous EAP-FAST provisioning.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed when enabling TLSv1.2 support for EAP-FAST since the
SSL_export_keying_material() call does not support the needed parameters
for TLS PRF and the external-to-OpenSSL PRF needs to be used instead.
Signed-off-by: Jouni Malinen <j@w1.fi>
This needs to use the new accessor functions since the SSL session
details are not directly accessible anymore and there is now sufficient
helper functions to get to the needed information.
Signed-off-by: Jouni Malinen <j@w1.fi>
This needs to use the new accessor functions for client/server random
since the previously used direct access won't be available anymore.
Signed-off-by: Jouni Malinen <j@w1.fi>
openssl_handshake() was checking only that in_data is not NULL and not
its length when determining whether to call BIO_write(). Extend that to
check the buffer length as well. In practice, this removes an
unnecessary BIO_write() call at the beginning of a TLS handshake on the
client side. This did not cause issues with OpenSSL versions up to
1.0.2, but that call seems to fail with the current OpenSSL 1.1.0
degvelopment snapshot. There is no need for that zero-length BIO_write()
call, so remove it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Report the feature capability on P2PS-PROV-START and P2PS-PROV-DONE
ctrl-iface events. A feature capability value is specified as
'feature_cap=<hex>' event parameter, where <val> is a hexadecimal
string of feature capability bytes in a PD Response frame.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
On PD Request/follow-on PD Request preparation set a feature capability
CPT value of PD context.
On PD Request processing use a request CPT and service advertisement
CPT priority list to select a feature capability CPT of PD Response.
On follow-on PD Request processing use a request CPT and a CPT priority
list in PD context to select a CPT value of follow on PD Response.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add a parameter allowing to specify a value of Coordination
Protocol Transport to P2PS_PROVISION and P2PS_PROVISION_RESP commands.
Extend the p2ps_provision structure to contain cpt_priority and
cpt_mask properties and initialize them on a P2PS PD request command.
The format of the parameter:
cpt=<cpt>[:cpt]
where <cpt> is CPT name e.g. UDP or MAC. The CPT names are listed
according to their preferences to be used for a specific P2PS session.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add Coordination Transport Protocol parameter to P2P_SERVICE_ADD
asp command.
Extend p2ps_advertisement structure to contain CPT priorities
and a supported CPT bitmask.
The format of the new parameter:
cpt=<cpt>[:<cpt>]
where <cpt> is a name of the Coordination Protocol Transport.
This implementation supports two CPT names: UDP and MAC.
The order of specified CPTs defines their priorities where
the first one has the highest priority.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add an auxiliary cstr_token() function to get a token from a const char
string. The function usage syntax is similar to str_token(), but unlike
str_token() the function doesn't modify the buffer of the string. Change
str_token() function implementation to use cstr_token().
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
The foreach_fst_group() loop needs "break-if-found", not
"continue-if-not-found" to do the search iteration properly. If there
were multiple groups, the previous design could have failed to find the
interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
fst_read_next_text_param() is never called with buflen <= 1, so this
separate error path is practically unreachable. Merge it with another
error path to make this a bit more compact.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for there to be multiple FST groups, so the hardcoded
mechanism of selecting the first one when sending out an event message
may not be sufficient. Get the interface from the caller, if available,
and if not, go through all groups in search of an interface to send the
event on.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for there to be multiple FST groups, so the hardcoded
mechanism of selecting the first one when sending out an event message
may not be sufficient. Get the interface from the caller, if available,
and if not, go through all groups in search of an interface to send the
event on.
Signed-off-by: Jouni Malinen <j@w1.fi>
Now that both hostapd and wpa_supplicant already enforce no duplicate
fst_attach() calls, there is no need for this check within fst_attach().
Signed-off-by: Jouni Malinen <j@w1.fi>
Dialog token is only 8 bits and maintaining u32 version of it in struct
fst_group resulted in incorrect wrap-around behavior in
fst_group_assign_dialog_token(). It was possible to assign u8
dialog_token value 0 because of this. Fix this by using u8 variable
consistently.
Signed-off-by: Jouni Malinen <j@w1.fi>
While this is always supposed to be the first element, check that this
is indeed the case instead of blindly using values from within the
element.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Element ID and Length subfields are not supposed to be included in
the Length. In addition, both of these subfields needs to be filled in
even for non-zero status code cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the previous PMF (CONFIG_IEEE80211W=y) design that used
functionality from the FT (CONFIG_IEEE80211R=y) changes to work without
requiring CONFIG_IEEE80211R=y build option to be included.
Signed-off-by: Ashok Ponnaiah <aponnaia@qti.qualcomm.com>
It was possible for a registered eloop socket handler to be unregistered
and re-registered for a re-opened socket with the same fd from a timeout
or signal handler. If such a case happened with the old socket having a
pending event waiting for processing, some eloop combinations could end
up calling the new handler function with the new socket and get stuck
waiting for an event that has not yet happened on the new socket. This
happened with timeout and signal handlers with all eloop.c types. In
addition to that, the epoll case could also trigger this when a socket
handler re-registered a re-opened socket.
Fix these by checking whether there has been socket handler changes
during processing and break the processing round by going back to
select/poll/epoll for an updated result if any changes are done during
the eloop handler calls before processing the old socket results.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the SIGINT/SIGTERM signal to be received while
processing a pending timeout/socket/signal event and then get stuck in
the following select() call before processing the signal event. If no
other events show up within the two second SIGALRM trigger, process will
be terminated forcefully even though there would have been possibility
to do clean termination assuming no operationg blocked for that two
second time.
Handle this more cleanly by checking for eloop.pending_terminate before
starting the select()/poll()/epoll_wait() wait for the following event.
Terminate the loop if pending signal handling requests termination.
In addition, make eloop_terminated() return 1 on eloop.pending_terminate
in addition to eloop.terminate since the process will be terminated
shortly and there is no point in starting additional processing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Introduce definitions for QCA vendor specific subcommands and attributes
to support multiport concurrency.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new mechanism can be used to combine multiple periodic AP
(including P2P GO) task into a single eloop timeout to minimize number
of wakeups for the process. hostapd gets its own periodic caller and
wpa_supplicant uses the previously added timer to trigger these calls.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, one timeout per process (by default every 30 seconds) was
used P2P peer expiration and another per-interface timeout (every 10
seconds) was used to expire BSS entries. Merge these to a single
per-process timeout that triggers every 10 seconds to minimize number of
process wakeups due to periodic operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this resulted in unnecessary wait and retransmission of the
previous EAP-Request. Change that to trigger immediate transmission of
EAP-Failure and disconnection since the EAP method cannot really recover
from this state.
Signed-off-by: Jouni Malinen <j@w1.fi>
This functionality was removed from the Host AP driver in May 2003, so
there is not any point in maintaining this in hostapd either.
Signed-off-by: Jouni Malinen <j@w1.fi>
The space separator between the command and the parameter was not
skipped properly and the first integer ended up being interpreted as 0
in all cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
fst_session_is_in_progress() is already checked as part of
fst_find_session_in_progress() before calling
fst_session_handle_action(). This is the only call path that can reach
fst_session_handle_tear_down() and as such, fst_session_is_in_progress()
cannot return 0 here.
Signed-off-by: Jouni Malinen <j@w1.fi>
There was a mix of EINVAL and -EINVAL returns through the FST
implementation. Make this more consistent by always returning -EINVAL in
error cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
The caller is not expected to free or modify the value since this is
returning a reference to a buffer maintained by the upper layer.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to add new functions with more or less identical
functionality of an already available helper function.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the hostapd global control interface ADD command to allow
driver wrapper to be specified ("ADD <ifname> <ctrl_iface> <driver>").
Previously, this case that did not use a configuration file allowed only
the default driver wrapper to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This experimental support for Texas Instruments C compiler was never
fully completed and it has not really been used in close to ten years,
so drop this to simply the header files.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a local variable and check the record payload length validity before
writing it into record->payload_length in hopes of getting rid of a
bogus static analyzer warning. The negative return value was sufficient
to avoid record->payload_length being used, but that seems to be too
complex for some analyzers. (CID 122668)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Typecasting &mgmt->u.action.u.fst_action to a struct pointer for various
FST Action frame payloads seemed to be triggering static analyzer
warnings about bounds checking since sizeof(mgmt->u.action.u.fst_action)
== 1 even though that is really a variable length structure. Try to
avoid this by calculating the pointer for the beginning of the frame
instead of variable length struct. (CID 125642)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the previously set SSID to remain in place between
test cases (e.g., in sequence "p2ps_connect_adv_go_persistent
p2p_set_ssid_postfix") and the P2P SSID postfix not getting used
properly. Make this less likely to occur by clearing the old SSID in
p2p_flush().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are confusing when the style used with the couple of FST IE checks
differs from the rest of hostapd/wpa_supplicant implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need for this function to be an inline function in a header
file since it is used only within fst_group.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 717333f4e4 ('FST: Add the Fast
Session Transfer (FST) module') performed incorrect frame length
validation for Setup Request (did not remove 24+1 header from
consideration) and did not include payload validation for other FST
Action frames. Fix these by explicitly verifying that the payload of
these frames is sufficiently long before reading the values from there.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to waste resources for this packet socket if FT-over-DS
is disabled or when operating P2P GO or AP mode in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds the FST IEs received from the FST module into Beacon, Probe
Response, and (Re)Association Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Fast Session Transfer (FST) is the transfer of a session from a channel
to another channel in a different frequency band. The term "session"
refers to non-physical layer state information kept by a pair of
stations (STAs) that communicate directly (i.e., excludes forwarding).
The FST is implemented in accordance with IEEE Std 802.11ad-2012.
Definitions
* FST interface - an interface for which FST functionality is enabled
* FST group - a bunch of FST interfaces representing single
multi-band STA
* FST peer - a multi-band capable STA connected
* FST module - multi-band operation functionality implemented in
accordance with IEEE Std 802.11ad-2012 (see 10.32
Multi-band operation) as a part of hostapd/wpa_supplicant
* FST manager - an external application that implements custom FST
related logic, using the FST module's interfaces
accessible via CLI or D-Bus
This commit introduces only the FST module. Integration of the FST
module into the hostapd/wpa_supplicant and corresponding CLI/D-Bus
interfaces and FST related tests are covered in separate commits.
FST manager application is out of scope of these commits.
As FST aggregates a few interfaces into FST group, the FST module uses
global CLI for both commands and notifications. It also exposes
alternative non-interface based D-Bus subtree for this purposes.
Configuration and Initialization
* FST functionality can enabled by compilation flag (CONFIG_FST)
* hostapd/wpa_supplicant controlling multiple interfaces are used for
FST
* once enabled by compilation, the FST can be enabled for specific
interfaces in the configuration files
* FST interfaces are aggregated in FST groups (fst_group_id config file
entry), where each FST group:
- represents one multi-band device
- should have two or more FST interfaces in it
* priority (fst_priority config file entry) must be configured for each
FST interface. FST interface with higher priority is the interface FST
will always try to switch to. Thus, for example, for the maximal
throughput, it should be the fastest FST interface in the FST setup.
* default Link Loss Timeout (LLT) value can be configured for each FST
interface (fst_llt config file entry). It represents LLT to be used
by FST when this interface is active.
* FST interfaces advertise the Multi-band capability by including the
Multi-band element in the corresponding frames
FST CLI commands:
* fst list_groups - list FST groups configured.
* fst list_ifaces - list FST interfaces which belong to specific group
* fst iface_peers - list Multi-Band STAs connected to specific interface
* fst list_sessions - list existing FST sessions
* fst session_get - get FST session info
* fst session_add - create FST session object
* fst session_set - set FST session parameters (old_iface, new_iface,
peer_addr, llt)
* fst session_initiate - initiate FST setup
* fst session_respond - respond to FST setup establishemnt attempt by
counterpart
* fst session_transfer - initiate FST switch
* fst session_teardown - tear down FST Setup but leave the session object
for reuse
* fst session_remove - remove FST session object
FST CLI notifications:
* FST-EVENT-PEER - peer state changed (CONNECT/DISCONNECT)
* FST-EVENT-SESSION - FST session level notification with following
sub-events:
- EVENT_FST_SESSION_STATE - FST session state changed
- EVENT_FST_ESTABLISHED - previously initiated FST session became
established
- EVENT_FST_SETUP - new FST session object created due to FST session
negotiation attempt by counterpart
All the FST CLI commands and notifications are also implemented on D-Bus
for wpa_supplicant.
IEEE 802.11 standard compliance
FST module implements FST setup statemachine in compliance with IEEE
802.11ad (P802.11-REVmc/D3.3), as it described in 10.32 Multi-band
operation (see also Figure 10-34 - States of the FST setup protocol).
Thus, for example, the FST module initiates FST switch automatically
when FST setup becomes established with LLT=0 in accordance with
10.32.2.2 Transitioning between states.
At the moment, FST module only supports non-transparent STA-based FST
(see 10.32.1 General).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This helper function can be used to check whether a MAC address is a
multicast (including broadcast) address.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit implements hostapd global control interface notifications
infrastructure. hostapd global control interface clients issue
ATTACH/DETACH commands to register and deregister with hostapd
correspondingly - the same way as for any other hostapd/wpa_supplicant
control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, hostapd only supported the case of EAPOL frames receiving
from interfaces enslaved into bridge. This commit adds support for any
Linux master (teaming, openvswitch, bonding, etc.) to be detected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new control interface command "EAPOL_REAUTH <MAC address>
<parameter> <value>" can be used to implement the IEEE 802.1X PAE
Set Authenticator Configuration operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
This new control interface command "EAPOL_REAUTH <MAC address>" can be
used to implement the IEEE 802.1X PAE Reauthenticate operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
If WPA2-Enterprise connection with full EAP authentication (i.e., no
PMKSA caching used) results in a PMKID that does not match the one the
AP/Authenticator indicates in EAPOL-Key msg 1/4, there is not much point
in trying to trigger full EAP authentication by sending EAPOL-Start
since this sequence was immediately after such full authentication
attempt.
There are known examples of authentication servers with incorrect MSK
derivation when TLS v1.2 is used (e.g., FreeRADIUS 2.2.6 or 3.0.7 when
built with OpenSSL 1.0.2). Write a clear debug log entry and also send
it to control interface monitors when it looks likely that this case has
been hit. After doing that, stop the connection attempt by
disassociating instead of trying to send out EAPOL-Start to trigger new
EAP authentication round (such another try can be tried with a new
association).
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a new STATUS command field "eap_tls_version" that shows the
TLS version number that was used during EAP-TLS/TTLS/PEAP/FAST exchange.
For now, this is only supported with OpenSSL.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new phase1 config parameter value tls_disable_tlsv1_0=1 can now be
used to disable use of TLSv1.0 for a network configuration. This can be
used to force a newer TLS version to be used. For example,
phase1="tls_disable_tlsv1_0=1 tls_disable_tlsv1_1=1" would indicate that
only TLS v1.2 is accepted.
Signed-off-by: Jouni Malinen <j@w1.fi>
While this is already enforced in practice due to the limits on the
maximum control interface command length and total_length bounds
checking here, this explicit check on payload_length value may help
static analyzers understand the code better. (CID 122668)
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the 32-bit record->total_length value to end up
wrapping around due to integer overflow if the longer form of payload
length field is used and record->payload_length gets a value close to
2^32. This could result in ndef_parse_record() accepting a too large
payload length value and the record type filter reading up to about 20
bytes beyond the end of the buffer and potentially killing the process.
This could also result in an attempt to allocate close to 2^32 bytes of
heap memory and if that were to succeed, a buffer read overflow of the
same length which would most likely result in the process termination.
In case of record->total_length ending up getting the value 0, there
would be no buffer read overflow, but record parsing would result in an
infinite loop in ndef_parse_records().
Any of these error cases could potentially be used for denial of service
attacks over NFC by using a malformed NDEF record on an NFC Tag or
sending them during NFC connection handover if the application providing
the NDEF message to hostapd/wpa_supplicant did no validation of the
received records. While such validation is likely done in the NFC stack
that needs to parse the NFC messages before further processing,
hostapd/wpa_supplicant better be prepared for any data being included
here.
Fix this by validating record->payload_length value in a way that
detects integer overflow. (CID 122668)
Signed-off-by: Jouni Malinen <j@w1.fi>
One possible outcome of the P2PS PD is P2P GO/P2P Client. In this case,
one peer becomes a P2P GO and the P2P Client joins it. Since multiple
GOs may run simultaneously on the same P2P Device, the P2P Client should
join using the intended interface address.
To be able to find the device by the intended interface address, save it
during the PD.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
If a device may be an explicit GO, it adds the GO details in the PD
Request. First, we try to reuse an active GO. If it is not present, we
try to reuse a non-active persistent group. In the latter case, if a
dedicated P2P interface is needed, the intended address should be that
of the pending interface. However, the wpas_get_go_info() provided the
ssid->bssid address, which is the address of the P2P device. This might
result in an incorrect intended interface attribute in the PD Request in
case a separate group interface is used.
Fix this by setting group_iface variable to true only if a dedicated
interface should be used and set the attribute accordingly.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Validate the PD Response frame contents more thoroughly when it is used
for P2PS.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When persistent group is used and the peer is GO in this group,
intended interface attribute should be added to PD request/response.
Not doing so violates the spec.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When device A sends PD response to device B, device A should save
wps_prov_info for device B. Not doing so would result in a redundant and
incorrect PD flow, e.g., when upon PROV-DISC-DONE event device B starts
a GO and device A should join it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
In case of a P2PS PD, allow keypad, display, and P2PS WPS config
methods. For a legacy PD, allow keypad, display, and pushbutton methods.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add 'else if' to P2PS status verification to prevent a redundant
condition checking. The first 'if' condition is true only if
status == P2P_SC_SUCCESS || status == P2P_SC_SUCCESS_DEFERRED.
while the second condition checks:
status != P2P_SC_SUCCESS &&
status != P2P_SC_FAIL_INFO_CURRENTLY_UNAVAILABLE &&
status != P2P_SC_SUCCESS_DEFERRED
Thus, the two conditions are mutually exclusive and 'else if' can be
used if this case.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Delete redundant comparison of msg.wps_config_methods with
dev->req_config_methods in p2p_process_prov_disc_resp() since it's
already done early in this function. Also, the second comparison
doesn't make too much sense: it can happen after a possible
p2p_reset_pending_pd() call setting dev->req_config_methods to 0.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When wpa_supplicant receives a PD Response with reject status it
generated P2P-PROV-DISC-FAILURE event without adv_id and adv_mac
parameters. Fix this by adding these parameters to the
wpas_prov_disc_fail() function call.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
This fixes the incomplete driver_hostap.c change from commit
5d180a7739 ('drivers: Add freq parameter
to send_mlme() function') that did not take into account the internal
callers.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Previously, only CONNECTING->CONNECTING case ended up sending out an
EAPOL-Start frame to avoid sending the unnecessary initial EAPOL-Start.
However, this optimization prevented new EAPOL-Start from being
initiated when leaving the HELD state. Allow that case to trigger
immediate EAPOL-Start transmission to speed up connection.
Signed-off-by: Jouni Malinen <j@w1.fi>
The only time the PIN should fail is when we initialize the TLS
connection, so it doesn't really make sense to get rid of the PIN just
because some other part of the handshake failed.
This is a followup to commit fd4fb28179
('OpenSSL: Try to ensure we don't throw away the PIN unnecessarily').
Signed-off-by: Mike Gerow <gerow@google.com>
The IPv6 address in the frame buffer may not be 32-bit aligned, so use a
local copy to align this before reading the address with 32-bit reads
(s6_addr32[]).
Signed-off-by: Jouni Malinen <j@w1.fi>
The 32-bit version of payload length field may not be 32-bit aligned in
the message buffer, so use WPA_GET_BE32() to read it instead of ntohl().
Signed-off-by: Jouni Malinen <j@w1.fi>
64-bit builds with CONFIG_WPA_TRACE=y resulted in the wpabuf pointers
getting misaligned (only 32-bit aligned) and that would result in reads
and writes of unaligned size_t values. Avoid this by indicating explicit
alignment requirement for wpabuf_trace to 8 octets (i.e., there will be
extra four octets of padding in case of 64-bit builds).
Similarly, struct os_alloc_trace resulted in some potential misalignment
cases, e.g., when CONFIG_ACS=y uses a 'long double' variable within
struct hostapd_channel_data. Avoid misalignment issues with explicit
alignment indication.
Signed-off-by: Jouni Malinen <j@w1.fi>
src/utils/list.h ended up defining a local version of offsetof() due to
stddef.h not getting included. This resulted in unnecessary warnings
from ubsan related to "dereferencing" of a NULL pointer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The input parameter ended up being converted to long int instead of int,
so use an explicit typecase to get rid of the compiler warning.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use explicit typecasting to avoid implicit conversion warnings in cases
where enum eap_erp_type is used in functions taking an EapType argument.
Signed-off-by: Jouni Malinen <j@w1.fi>
The FT-specific check for valid group cipher in wpa_ft_gen_req_ies() was
not up-to-date with the current list of supported ciphers. Fix this by
using a generic function to determine validity of the cipher. In
practice, this adds support for using CCMP-256 and GCMP-256 as the group
cipher with FT.
Signed-off-by: Jouni Malinen <j@w1.fi>
This mechanism to figure out TLS library capabilities has not been used
since commit fd2f2d0489 ('Remove
EAP-TTLSv1 and TLS/IA') (Sep 2011).
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to have separate return statements for these corner
cases that are unlikely to be hit in practice.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to have separate return statements for these corner
cases that are unlikely to be hit in practice.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new TEST_FAIL and GET_FAIL control interface commands can be used
similarly to the earlier TEST_ALLOC_FAIL/GET_ALLOC_FAIL design. The new
version is more generic framework allowing any function to be annotated
for failure testing with the TEST_FAIL() macro. This mechanism is only
available in builds with CONFIG_WPA_TRACE_BFD=y and
CONFIG_TESTING_OPTIONS=y. For other builds, the TEST_FAIL() macro is
defined to return 0 to allow the compiler to remove the test code from
normal production builds.
As the first test site, allow os_get_random() to be marked for failing
based on call backtrace.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not allow 40 MHz co-ex PRI/SEC switch to force us to change our PRI
channel if we have an existing connection on the selected PRI channel
since doing multi-channel concurrency is likely to cause more harm than
using different PRI/SEC selection in environment with multiple BSSes on
these two channels with mixed 20 MHz or PRI channel selection.
Signed-off-by: Jouni Malinen <j@w1.fi>
Fix a condition when Advertised Service Info Attribute is added to
a probe response in p2p_buf_add_service_instance(). The issue is
that a 'found' value is increased even if 'test' and 'adv->hash' hashes
are different. As result 'found' may have a non-zero value when an
attribute data length is 0. In this cause an empty attribute is about to
be added. Fixing it by eliminating 'found' and checking 'total_len'
containing a real number of bytes added to Advertised Service Info
Attribute.
This fixes an issue from commit 50a9efe713
('P2PS: Fix Probe Response frame building in error cases').
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
The cwmin/cwmax parameters were limited more than is needed. Allow the
full range (0..15 for wmm_ac_??_{cwmin,cwmax} and 1..32767 for
tx_queue_data?_{cwmin,cwmax}) to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The current P802.11 description of SAE uses "1 < element < p" as the
required range. However, this is not correct and does not match the
Dragonfly description of "1 < element < p-1". SAE definition will need
to change here. Update the implementation to reject p-1 based on the
correct rule here.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the P2PS Probe Response frame to go out on the
channel on which a Probe Request frame was reported even when we are
just about to start Listen mode on another channel. This could result in
the peer device using incorrect channel for us. Fix this by skipping the
response in this special case while waiting for Listen mode to start.
This showed up as a hwsim test failure with test sequence "gas_fragment
p2ps_connect_display_method_nonautoaccept" in cases where the dev[0]
Listen channel was not same as the AP operating frequency in the GAS
test.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2012 description of SAE does not require this, i.e., it
describes the requirement as 0 < scalar < r for processing the Commit
message. However, this is not correct and will be changes to 1 < scalar
< r to match the Dragonfly description so that a trivial secret case
will be avoided explicitly.
This is not much of an issue for the locally generated commit-scalar
since it would be very unlikely to get the value of 1. For Commit
message processing, a peer with knowledge of the password could
potentially force the exchange to expose key material without this
check.
Signed-off-by: Jouni Malinen <j@w1.fi>
This provides more information to upper layer programs on what happens
with connection attempts in cases where the enabled networks are not
found in scan results.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
wpa_supplicant has stub functions if the external p2p symbols are
unavailable, but the build still fails if the
wpa_driver_nl80211_driver_cmd symbol is missing. Fix this by leaving the
function pointer NULL. This is safe because wpa_drv_driver_cmd() performs
a NULL check.
Signed-off-by: Kevin Cernekee <cernekee@google.com>
If BOARD_HOSTAPD_PRIVATE_LIB is not used on an Android build, we will
need to replace both the p2p functions *and* wpa_driver_nl80211_driver_cmd
in order to successfully link. Let's make the name more generic so it is
more obvious what it is used for.
Suggested-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Kevin Cernekee <cernekee@google.com>
In case memory allocation fails, data->pac_opaque_encr_key may be NULL
and lead to possible crash.
Signed-off-by: Maneesh Jain <maneesh.jain@samsung.com>
Even though this OpenSSL function is documented as returning "1 if point
if on the curve and 0 otherwise", it can apparently return -1 on some
error cases. Be prepared for that and check explicitly against 1 instead
of non-zero.
Signed-off-by: Jouni Malinen <j@w1.fi>
If PWE is discovered before the minimum number of loops (k) is reached,
the extra iterations use a random "password" to further obfuscate the
cost of discovering PWE.
Signed-off-by: Jouni Malinen <j@w1.fi>
This replaces the earlier IEEE Std 802.11-2012 algorithm with the design
from P802.11-REVmc/D4.0. Things brings in a blinding technique for
determining whether the pwd-seed results in a suitable PWE value.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the IKE groups 27-30 (RFC 6932) to be used with OpenSSL
1.0.2 and newer. For now, these get enabled for SAE as configurable
groups (sae_groups parameter), but the new groups are not enabled by
default.
Signed-off-by: Jouni Malinen <j@w1.fi>
draft-irtf-cfrg-dragonfly recommends implementation to set the security
parameter, k, to a value of at least 40. This will make PWE generation
take significantly more resources, but makes it more likely to hide
timing differences due to different number of loops needed to find a
suitable PWE.
Signed-off-by: Jouni Malinen <j@w1.fi>
This check explicitly for reflection attack and stops authentication
immediately if that is detected instead of continuing to the following
4-way handshake that would fail due to the attacker not knowing the key
from the SAE exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
OpenSSL 0.9.8 (and newer) includes SSL_CTX_get_app_data() and
SSL_CTX_set_app_data(), so there is no need to maintain this old
OPENSSL_SUPPORTS_CTX_APP_DATA backwards compatibility design.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, it would have been possible for va_end(args) to be called
twice in case mp_init() fails. While that may not cause issues on number
of platforms, that is not how va_start()/va_end() are supposed to be
used. Fix this by returning from the function without using va_end()
twice on the same va_list args.
Signed-off-by: Jouni Malinen <j@w1.fi>
The construction used here to figure out the offset of variable length
IEs in Probe Request frames was a bit odd looking and resulted in a
warning from a static analyzer, so replace it with more standard use of
offsetof().
Signed-off-by: Jouni Malinen <j@w1.fi>
The flags argument is used to indicate a failure case (0x80) which
allows erp == NULL. This may be a bit too difficult combination for
static analyzers to understand, so add an explicit check for !erp as
another condition for returning from the function before the erp pointer
gets dereferenced without checking it.
Signed-off-by: Jouni Malinen <j@w1.fi>
drv cannot be NULL here (it is dereferenced even on the preceding line)
and anyway, os_free(NULL) is allowed, so remove the redundant check.
Signed-off-by: Jouni Malinen <j@w1.fi>
The eap argument to this function is never NULL and the earlier
ieee802_1x_learn_identity() call is dereferencing it anyway, so there is
no point in checking whether it is NULL later in the function.
Signed-off-by: Jouni Malinen <j@w1.fi>
This needs to find the PRI channel also in cases where the affected
channel is the SEC channel of a 40 MHz BSS, so need to include the
scanning coverage here to be 40 MHz from the center frequency. Without
this, it was possible to miss a neighboring 40 MHz BSS that was at the
other end of the 2.4 GHz band and had its PRI channel further away from
the local BSS.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to have separate return statements for these corner
cases that are unlikely to be hit in practice.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the common WLAN-* RADIUS attributes were added only when WPA
or WPA2 was used. These can be of use for OSEN as well, so include them
in that case, too.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to have a separate "fail silently" case for wpa_ie_len
== 0. That condition does not seem to be reachable and even if it were,
the following "ie len too short" case will result in the exact same
return value.
Signed-off-by: Jouni Malinen <j@w1.fi>
As far as IEEE 802.11 standard is concerned, WEP is deprecated, but at
least in theory, allowed as a group cipher. This option is unlikely to
be deployed anywhere and to clean up the implementation, we might as
well remove all support for this combination.
Signed-off-by: Jouni Malinen <j@w1.fi>
Sending a wowlan configuration command can be done on any wireless
interface (not only netdev), as it is a device configuration and not
interface configuration specific. Fix the code to allow it to be
sent on any interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Android libnl_2 implementation added support for "nl80211" name in
commit 'libnl_2: Extend genl_ctrl_resolve() to support "nl80211" name'
in July 2012 which got included in Android 4.2. It is fine to drop this
old Android ICS workaround from wpa_supplicant now.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
p2p_process_nfc_connection_handover() allocates msg memory in the parser
and might return before memory is released if the received message is
not valid.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
If key derivation fails, there is no point in trying to continue
authentication. In theory, this could happen if memory allocation during
TLS PRF fails.
Signed-off-by: Jouni Malinen <j@w1.fi>
Free tmp_out before returning to prevent memory leak in case the second
memory allocation in openssl_tls_prf() fails. This is quite unlikely,
but at least theoretically possible memory leak with EAP-FAST.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
org.wi-fi.wfds service is not a replacement for non-WFA service matches.
Do not try to replace the results with that if there is not sufficient
room for the response. Instead, reply with all the matching services
that fit into the message. org.wi-fi.wfds is the first entry in the list
(if matching request/service is present), so it won't get overridden by
other services.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The service hash for org.wi-fi.wfds is supposed to match only if the
device has a WFA defined org.wi-fi.wfds.* service. Verify that before
adding org.wi-fi.wfds to the response.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Probe Response building is already doing service matching and there is
no need to do this in both places, so simplify the p2p_reply_probe()
implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When doing initial processing of Probe Request frame service hashes, the
previous implementation dropped all other hash values if a hash for
org.wi-fi.wfds was included. This is not correct, since that is not a
full wildcard of all services (it only matches WFA defined
org.wi-fi.wfds.* services).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This "wildcard" match is for WFA specified org.wi-fi.wfds.* services,
not for all services. Verify that there is a really matching service
being advertised instead of assuming this "wildcard" matches if any
services are advertised.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The org.wi-fi.wfds "wildcard" is not a full wildcard of all service
names and as such, it must not remove other service name hash values
from the Probe Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
p2ps_gen_hash() has a limit on service names based on the temporary
buffer from stack. Verify that the service name from the local P2P_FIND
command is short enough to fix into that buffer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Quoting P2PS specification: "If multiple Service Hash values are
included in the Probe Request frame, then the ASP shall find a match for
each Service Hash, and it shall send a Probe Response frame with the
information listed in this section for all matched Service Hashes." This
commit changes handling of wildcard hash matching by adding a
wildcard 'org.wi-fi.wfds' info together with the other hash matches.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add auxiliary functions to write a single advertised service info record
into a wpabuf and to find P2PS wildcard hash in a received hash
attribute. Re-factor p2p_buf_add_service_instance() function to allow
adding new wildcard types in future commits.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When hostapd or wpa_supplicant is run in debug more with key material
prints allowed (-K on the command line), it is possible for passwords
and keying material to show up in debug prints. Since some of the debug
cases end up allocating a temporary buffer from the heap for processing
purposes, a copy of such password may remain in heap. Clear these
temporary buffers explicitly to avoid causing issues for hwsim test
cases that verify contents of memory against unexpected keys.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Avoid using p2p_data::query_hash for both Probe Request frame processing
and for hashes specified by p2p_find. It's resolved by use of local
query_hash and query_count variables in p2p_reply_probe().
Since p2p_data::query_hash is used only for seek hash values rename
p2p_data::query_hash to p2ps_seek_hash.
Delete p2p_data::query_count since it's not needed anymore.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Commit 86bd36f0d5 ('Add generic mechanism
for adding vendor elements into frames') introduced a mechanism to add
vendor elements into various frames, but missed the addition to the
Invitation Response frame. This commit addresses the same.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This variable is used locally only in the p2p_reply_probe() function.
The value of this variable is valid only in the context of the single
Probe Request message handling and doesn't make much sense in p2p
context.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Free a PD context with a function encapsulating both os_free() call and
setting a PD context pointer to NULL.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
A P2P Client may be discoverable and reply to Probe Request frames,
while at the same time the P2P GO would also be discoverable and include
the P2P Client information in the P2P Group Info attribute of the Probe
Response frames.
If a seeker constantly hears the Probe Response frames from a P2P Client
and then from the GO, but handles them in the opposite order (due to
scan results ordering), the more valuable Probe Response frame from the
P2P Client will be ignored. Fix this by defining a threshold (1 second)
during which the direct Probe Response frame will be preferred over the
information acquired from the GO and will not be considered as old.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When adding group clients to the P2P peer list, use the driver provided
BSS entry timestamp instead of the current time. Otherwise, the time
comparison which is made in p2p_add_device() doesn't make sense.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
If the RX frequency of the Probe Request frame is known, specify it when
sending the Probe Response frame. This is needed when the Probe Request
frame is received on another virtual interface, for example, when a GO
or P2PS client are discoverable on the group operating channel.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Change send_mlme() API to allow sending management frames on a specific
channel, overriding the internal driver decision.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Return P2P_PREQ_PROCESSED instead of P2P_PREQ_NOT_PROCESSED on
a successful Probe Request frame handling in p2p_reply_probe().
Verify a return value of p2p_reply_probe() in p2p_probe_req_rx()
and continue a pending invitation/connection flow only if the
Probe Request frame is from an expected P2P peer.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
In some cases, Probe Request frames can be received by a peer not only
on a listen channel. In this case an additional rx_freq parameter
explitly contains a Probe Request frame RX frequency. In case rx_freq is
set to 0, a Probe Request frame RX channel is assumed to be our own
listen channel (p2p->cfg->channel).
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
CA country code was included mistakenly (copy-paste..) in cn_op_class_cc
while it was supposed to be included only in us_op_class_cc. In
practice, this did not result in incorrect operation due to the
us_op_class_cc list being checked first. Anyway, better fix
cn_op_class_cc to avoid confusion here.
Signed-off-by: Jouni Malinen <j@w1.fi>
This increases code coverage for gas.c testing to cover areas that
cannot be reached with pure hwsim test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Currently, if multiple bss share are bridge and tagged vlan interface,
only the first instance of struct hostapd_vlan for this vlanid will have
the DVLAN_CLEAN_VLAN flag added. Thus, when this instance is removed,
the tagged vlan interface will be removed from bridge, thought other bss
might still need it. Similarily, the bridge will be left over, as the
does not have zero ports when the first instance of a struct
hostapd_vlan is freed.
This patch fixes this by having a global (per process) reference counter
for dynamic tagged vlan and dynamically created bridge interfaces, so
they are only removed after all local users are freed. (struct
hapd_interfaces *)->vlan_priv is used to hold src/ap/vlan_init.c global
per-process data like drv_priv does; right now this is only used for the
interface reference counting, but could get extended when needed. Then
possibly some vlan_global_init / vlan_global_deinit should be added, but
this is not required right now.
Additionally, vlan->configured is checked to avoid reference counter
decreasing before vlan_newlink increased them.
In order to avoid race conditions, vlan_dellink is called explicitly
after hostapd_vlan_if_remove. Otherwise there would be a short timeframe
between hostapd_vlan_if_remove and vlan_dellink during which the struct
hostapd_vlan still exists, so ap_sta_bind_vlan would try to attach
stations to it.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Add operating class 125 (channels 149..169) to the list of P2P supported
channels. This allows the 5 GHz channels 161 and 169 to be used for P2P
GO when those channels are allowed for AP mode in the current regulatory
domain.
Signed-off-by: Amr BEN ABDESSALEM <amrx.ben.abdessalem@intel.com>
Instead of an int variable with magic values 0, 1, 2, use an enum that
gives clearer meaning to the values now that the original boolean type
global argument is not really a boolean anymore.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 95b6bca66d ('Add rsn_pairwise bits
to set_ieee8021x() driver_ops') modified cipher configuration to use
unconditionally wpa_pairwise | rsn_pairwise. While that works for many
cases, it does not handle the case of dynamic configuration changes over
the control interface where wpa_pairwise or rsn_pairwise values may not
get cleared when the wpa parameter is modified. Fix this inconsistency
by configuring the driver with only the bits that are valid for the
currently enabled WPA/WPA2 version(s).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add GO Intent information of connecting device in GO Negotiation Request
event which will help applications to decide its own GO intent value in
advance and can avoid failure cases when both devices use GO Intent 15
depending on application requirement.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
So that systems with bad clocks will send random session IDs,
instead of always ones starting at the same second.
If os_get_random() isn't available, use os_get_time(). But also
mix in now.tv_usec, so that the accounting session ID is more
likely to be globally and temporally unique.
Signed-off-by: Alan DeKok <aland@freeradius.org>
The OPENSSL_VERSION_NUMBER < 0x00909000L case of
openssl_get_keyblock_size() had not been kept in sync with the cleanup
changes.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Explicitly check for iface->current_mode before dereferencing it. While
this case may not happen in practice, it is better for the setup
functions to be more careful when doing the initial band selection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When device supports dual band operations with offloaded ACS, hw_mode
can now be set to any band (hw_mode=any) in order to allow ACS to select
the best channel from any band. After a channel is selected, the hw_mode
is updated for hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While RFC 6124 does not define how Session-Id is constructed for
EAP-EKE, there seems to be consensus among the authors on the
construction. Use this Type | Nonce_P | Nonce_S construction based on
the following email:
From: Yaron Sheffer <yaronf.ietf at gmail.com>
To: ietf at ietf.org
Date: Wed, 17 Nov 2010 13:13:42 +0200
Expanding on my previous response, I suggest to resolve Bernard's
concern by adding the following text:
5.6 EAP Key Generation
EAP-EKE can be used for EAP key generation, as defined by [RFC 5247].
When used in this manner, the values required to establish the key
hierarchy are defined as follows:
- Peer-Id is the EAP-EKE ID_P value.
- Server-Id is the EAP-EKE ID_S value.
- Session-Id is the concatenated Type | Nonce_P | Nonce_S, where Type is
the method type defined for EAP-EKE in [Sec. 4.1], a single octet.
Thanks,
Yaron
Signed-off-by: Jouni Malinen <j@w1.fi>
The ACS code part of hostapd scans all the channels even if the channel
list is specified in the hostapd.conf. Limit the ACS scan channels to
the list specified in the config file.
Signed-off-by: Srinivasa Duvvuri<sduvvuri@chromium.org>
Do not add a P2P IE when a station interface is trying to associate
to an AP or P2P GO that publishes a P2P IE but does not include
a P2P manageability attribute.
This addresses an interoperability issue that was reported in
https://bugzilla.kernel.org/show_bug.cgi?id=96471, where a P2P GO
rejects association from a station interface without a specified
reason.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Link Property query vendor command shall facilitate the information
of the Wi-Fi link. MAC address of the Wi-Fi peer is given as an input
for querying the link properties.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The cleanup code will handle this, but it is more robust to make sure
this is cleared to zero when allocating a new buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The cleanup code will handle this, but it is more robust to make sure
this is cleared to zero when allocating a new buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The L (Length) and M (More) flags needs to be cleared before deciding
whether the locally generated response requires fragmentation. This
fixes an issue where these flags from the server could have been invalid
for the following message. In some cases, this could have resulted in
triggering the wpabuf security check that would terminate the process
due to invalid buffer allocation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The remaining number of bytes in the message could be smaller than the
Total-Length field size, so the length needs to be explicitly checked
prior to reading the field and decrementing the len variable. This could
have resulted in the remaining length becoming negative and interpreted
as a huge positive integer.
In addition, check that there is no already started fragment in progress
before allocating a new buffer for reassembling fragments. This avoid a
potential memory leak when processing invalid message.
Signed-off-by: Jouni Malinen <j@w1.fi>
The remaining number of bytes in the message could be smaller than the
Total-Length field size, so the length needs to be explicitly checked
prior to reading the field and decrementing the len variable. This could
have resulted in the remaining length becoming negative and interpreted
as a huge positive integer.
In addition, check that there is no already started fragment in progress
before allocating a new buffer for reassembling fragments. This avoid a
potential memory leak when processing invalid message.
Signed-off-by: Jouni Malinen <j@w1.fi>
The length of the received Commit and Confirm message payloads was not
checked before reading them. This could result in a buffer read
overflow when processing an invalid message.
Fix this by verifying that the payload is of expected length before
processing it. In addition, enforce correct state transition sequence to
make sure there is no unexpected behavior if receiving a Commit/Confirm
message before the previous exchanges have been completed.
Thanks to Kostya Kortchinsky of Google security team for discovering and
reporting this issue.
Signed-off-by: Jouni Malinen <j@w1.fi>
The length of the received Commit and Confirm message payloads was not
checked before reading them. This could result in a buffer read
overflow when processing an invalid message.
Fix this by verifying that the payload is of expected length before
processing it. In addition, enforce correct state transition sequence to
make sure there is no unexpected behavior if receiving a Commit/Confirm
message before the previous exchanges have been completed.
Thanks to Kostya Kortchinsky of Google security team for discovering and
reporting this issue.
Signed-off-by: Jouni Malinen <j@w1.fi>
The length of the WMM Action frame was not properly validated and the
length of the information elements (int left) could end up being
negative. This would result in reading significantly past the stack
buffer while parsing the IEs in ieee802_11_parse_elems() and while doing
so, resulting in segmentation fault.
This can result in an invalid frame being used for a denial of service
attack (hostapd process killed) against an AP with a driver that uses
hostapd for management frame processing (e.g., all mac80211-based
drivers).
Thanks to Kostya Kortchinsky of Google security team for discovering and
reporting this issue.
Signed-off-by: Jouni Malinen <j@w1.fi>
The debug information from httpread can be helpful in figuring out error
cases in general and as such, should be enabled by default. Get rid of
the hardcoded httpread_debug value that would require source code
changes to enable.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to continue processing a HTTP body when it becomes
clear that the end result would be over the maximum length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that ncopy parameter to memcpy is not negative. While this is not
supposed to be needed, it is a good additional protection against
unknown implementation issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
strtoul() return value may end up overflowing the int h->chunk_size and
resulting in a negative value to be stored as the chunk_size. This could
result in the following memcpy operation using a very large length
argument which would result in a buffer overflow and segmentation fault.
This could have been used to cause a denial service by any device that
has been authorized for network access (either wireless or wired). This
would affect both the WPS UPnP functionality in a WPS AP (hostapd with
upnp_iface parameter set in the configuration) and WPS ER
(wpa_supplicant with WPS_ER_START control interface command used).
Validate the parsed chunk length value to avoid this. In addition to
rejecting negative values, we can also reject chunk size that would be
larger than the maximum configured body length.
Thanks to Kostya Kortchinsky of Google security team for discovering and
reporting this issue.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the mp_init_multi() call had failed due to memory allocation failure,
mp_div() would have returned 1 instead of MP_MEM (-2). It looks like all
callers are checking the return value against MP_OKAY instead of <1
(etc.), so this does not seem to result in difference in behavior.
Anyway, it's best to fix the mp_div() return value for the MP_MEM error
case to avoid unexpected behavior.
Signed-off-by: Maks Naumov <maksqwe1@ukr.net>
In theory, the previous version could have resulted in reading one byte
beyond the end of the management frame RX buffer if the local driver
were to deliver a truncated Public Action frame for processing. In
practice, this did not seem to happen with mac80211-based drivers and
even if it were, the extra octet would be an uninitialized value in a
buffer rather than read beyond the end of the buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was previously checked as part of the eap_sim_parse_attr()
processing, but it is easier to review the code if there is an
additional explicit check for confirming that the Reserved field is
present since the pos variable is advanced beyond it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Clean up eap_sake_parse_add_attr() design by passing in pointer to the
payload of the attribute instead of parsing these separately for each
attribute within the function.
Signed-off-by: Jouni Malinen <j@w1.fi>
The req_plen argument to eap_pax_process_std_1() and
eap_pax_process_std_3() could be smaller than sizeof(struct eap_pax_hdr)
since the main processing function was only verifying that there is
enough room for the ICV and then removed ICV length from the remaining
payload length.
In theory, this could have resulted in the size_t left parameter being
set to a negative value that would be interpreted as a huge positive
integer. That could then result in a small buffer read overflow and
process termination if MSGDUMP debug verbosity was in use.
In practice, it does not seem to be feasible to construct a short
message that would be able to pass the ICV validation (calculated using
HMAC-SHA1-128) even for the case where an empty password is used.
Anyway, the implementation should really check the length explicitly
instead of depending on implicit check through ICV validation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The EAP-TLS-based helper functions can easily use struct wpabuf in more
places, so continue cleanup in that direction by replacing separate
pointer and length arguments with a single struct wpabuf argument.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function is only using the Identifier field from the EAP request
header, so there is no need to pass it a pointer to the full message.
This makes it a bit easier to analyze the area that gets access to
unverified message payload.
Signed-off-by: Jouni Malinen <j@w1.fi>
MS-MPPE-Recv-Key generation in radius_msg_add_mppe_keys() used incorrect
function argument (send_key_len; should be recv_key_len) when allocating
a temporary buffer. Fix this by using the correct argument.
The only caller of the function uses the same length for both
send_key_len and recv_key_len, so this copy-paste error did not result
in any difference in the behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Handling of WPS RF band for 60 GHz was missing. Add it in all relevant
places and also map "AES" as the cipher to GCMP instead of CCMP when
operating on the 60 GHz band.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
It was possible for the WPA_ALG_PMK algorithm in set_key() to result in
trying to configure a key with cipher suite 0. While this results in a
failure from cfg80211 or driver, this is not really desirable operation,
so add a check for cipher suite conversion result before issuing the
nl80211 command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This can be used with Proxy ARP to allow multicast NAs to be forwarded
to associated STAs using link layer unicast delivery. This used to be
hardcoded to be enabled, but it is now disabled by default and can be
enabled with na_mcast_to_ucast=1. This functionality may not be desired
in all networks and most cases work without it, so the new
default-to-disabled is more appropriate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, struct wpa_group was created when the first station enters
the group and the struct wpa_group was not freed when all station left
the group. This causes a problem because wpa_group will enter
FATAL_FAILURE when a wpa_group is running while the AP_VLAN interface
has already been removed.
Fix this by adding a reference counter to struct wpa_group and free a
group if it is unused.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
If hostapd has bound a STA into a specific VLAN, the new vlan_id
parameter in the control interface STA command can now be used to check
which VLAN ID is in use.
Signed-off-by: Jouni Malinen <j@w1.fi>
All the system header files are supposed to be included before any other
internal header file apart from utils/includes.h.
Signed-off-by: Jouni Malinen <j@w1.fi>
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Now on an engine error we decode the error value and determine if the
issue is due to a true PIN error or not. If it is due to incorrrect PIN,
delete the PIN as usual, but if it isn't let the PIN be.
Signed-off-by: Mike Gerow <gerow@google.com>
Previously, mesh state machine transmits updated Commit Message when
receiving a Confirm Message in Committed state. According to the
standard, it should (re)send the latest Commit Message previously sent.
IEEE Std 802.11-2012, 11.3.8.6.4 Protocol instance behavior - Committed
state:
"Upon receipt of a Con event, ... If Sync is not greater than
dot11RSNASAESync, the protocol instance shall increment Sync, transmit
the last Commit Message sent to the peer, and set the t0
(retransmission) timer."
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends dynamic_vlan=required checks to apply for WPA-PSK with
macaddr_acl=2 (RADIUS) case.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Previously, only P2P and mesh use cases enforced unique MAC address for
a dynamically added virtual interface. Extend this to cover normal
station mode interfaces since those can now be added with INTERFACE_ADD.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to try to derive DH shared key with a peer that tries
to use too short or too long DH Public Key. Previously, such cases ended
up implicitly getting rejected by the DH operations failing to produce
matching results. That is unnecessarily, so simply reject the message
completely if it does not have a Public Key with valid length. Accept
couple of octets shorter value to be used to avoid interoperability
issues if there are implementations that do not use zero-padding
properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
This enforces variable length strings Manufacturer, Model Name, Model
Number, and Serial Number to be within the maximum length defined in the
WSC specification. While none of the existing users for these within
hostapd/wpa_supplicant had problems with longer strings, it is good to
ensure the strings are not longer to avoid potential issues at higher
layer components.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Remove the length field from struct ieee802_11_elems since the only
allowed element length is five and that is checked by the parser.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the only allowed element length is one.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the only allowed element length is one.
Signed-off-by: Jouni Malinen <j@w1.fi>
All the existing users of these elements were already validating the
element length. However, it is clearer to validate this already at the
parser for extra layer of protection for any future changes.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 88b32a99d3 ('FT: Add FT AP support
for drivers that manage MLME internally') added an alternative way of
processing the WMM TSPEC from RIC. However, that change did not seem to
include the same checks for WMM TSPEC element length that were used in
the original implementation for MLME-in-hostapd case. Fix this by
sharing the older implementation of copying the WMM TSPEC from RIC for
both cases.
It looks like the destination buffer for the response is sufficiently
long for the fixed length copy, but it may have been possible to trigger
a read beyond the end of the FTIE by about 50 bytes. Though, that seems
to be within the buffer received for RX buffer in the case that uses
this driver-based AP MLME design for FT.
Signed-off-by: Jouni Malinen <j@w1.fi>
This program can be used to run fuzzing tests for areas related to EAPOL
frame parsing and processing on the supplicant side.
Signed-off-by: Jouni Malinen <j@w1.fi>
This program can be used to run fuzzing tests for areas related to P2P
message parsing and processing. p2p-fuzzer allows data files to be used
to inject Probe Response and Action frames for processing by the P2P
module.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it more obvious that the wps_parse_msg() bounds checking is
used to verify that there is sufficient space in the P2P buffer for the
secondary device types.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This modifies couple of code segments that replaced control characters
in strings with '_' to use a common helper function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While it looks like all the users of this parsed attribute were able to
handle longer SSID values, there is no valid use case for these and to
avoid any potential future issues, enforce maximum length (32 bytes) on
the SSID during parsing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While it looks like all the users of this parsed attribute were able to
handle longer Device Name values, there is no valid use case for these
and to avoid any potential issues in upper layer components, enforce
maximum length (32 bytes) on the Device Name during parsing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While none of the current users of msg.persistent_ssid{,_len} would have
issues with too long SSID value, it is safer to enforce bounds checking
on the SSID while parsing the attribute to avoid any potential issues in
the future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The SSID element is defined to have a valid length range of 0-32. While
this length was supposed to validated by the users of the element
parser, there are not really any valid cases where the maximum length of
32 octet SSID would be exceeded and as such, the parser itself can
enforce the limit as an additional protection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes a possible memcpy overflow for P2P dev->oper_ssid in
p2p_add_device(). The length provided by the peer device (0..255 bytes)
was used without proper bounds checking and that could have resulted in
arbitrary data of up to 223 bytes being written beyond the end of the
dev->oper_ssid[] array (of which about 150 bytes would be beyond the
heap allocation) when processing a corrupted management frame for P2P
peer discovery purposes.
This could result in corrupted state in heap, unexpected program
behavior due to corrupted P2P peer device information, denial of service
due to process crash, exposure of memory contents during GO Negotiation,
and potentially arbitrary code execution.
Thanks to Google security team for reporting this issue and smart
hardware research group of Alibaba security team for discovering it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The multi-SSID design that used a single beaconing BSSID with multiple
SSIDs was never completed in this repository, so there is no need to
maintain the per-STA ssid/ssid_probe pointers that could only point to
&hapd->conf->ssid. Save some memory and reduce code complexity by
removing this unused partial capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit fa0e715100 ('Use
tls_connection_prf() for all EAP TLS-based key derivation') copied some
pointer checks from the generic implementation to tls_openssl.c.
However, these are arrays and cannot be NULL in OpenSSL data. Remove the
unnecessary checks and add master_key_length check for completeness.
(CID 109619).
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to interpret debug logs for cases where hostapd
control multiple interfaces.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to interpret debug logs in case hostapd controls
multiple interfaces and a STA roams between them.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Currently, vlan_remove_dynamic() is only called when the station VLAN ID
is changed (ap_sta_bind_vlan), but not when the station is freed. So
dynamic VLAN interfaces are not removed actually except within 1x
reauthentification VLAN ID change, although most of the code is already
there.
This patch fixes this by calling vlan_remove_dynamic() in ap_free_sta().
It cannot just use sta->vlan_id for this, as this might have been
changed without calling ap_sta_bind_vlan() (ap/ieee802_11.c:handle_auth
fetches from RADIUS cache for WPA-PSK), thus reference counting might
not have been updated. Additionally, reference counting might get wrong
due to old_vlanid = 0 being passed unconditionally, thus increasing the
reference counter multiple times.
So tracking the currently assigned (i.e., dynamic_vlan counter
increased) VLAN is done in a new variable sta->vlan_id_bound. Therefore,
the old_vlan_id argument of ap_sta_bind_vlan() is no longer needed and
setting the VLAN for the sta in driver happens unconditionally.
Additionally, vlan->dynamic_vlan is only incremented when it actually
is a dynamic VLAN.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
hostapd receives NEWLINK messages multiple times and thus does
configuration of the the vlan interface multiple times.
This is not required and leads to the following during cleanup in
test pmksa_cache_preauth_vlan_used:
1. run-test.py does: brctl delif brvlan1 wlan3.1
2. hostapd processes NEWLINK and does: brctl addif brvlan1 wlan3.1
3. run-test.py does: brctl delbr brvlan1
-> fails as wlan3.1 is still in the bridge
This patch fixes this by ignoring repeated NEWLINK messages.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
When hitting
> Failed to create interface wlan3.1: -23 (Too many open files in system)
> Try to remove and re-create wlan3.1
hostapd deletes the AP_VLAN interface and then recreates it. Thus the
kernel assigns the same ifidx to the new interfaces and sends DELLINK
and NEWLINK mesages.
As the DELLINK messages are processed after the struct hostapd_vlan is
added, hostapd deletes the struct hostapd_vlan entry, deconfigures the
AP_VLAN interface and leaves vlan_newlink nothing to find afterwards.
So this patch makes DELLINK messages to be ignored when the interface
exists.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Previously, during RSN preauthentication, ap_sta_bind_vlan() was called,
which fails for non-zero sta->vlan_id as the station is not known to the
kernel driver.
Fix this by binding the station only if it is associated. If it is not
associated, ap_sta_bind_vlan() will be done later during association.
In addition, reject Access-Accept if the returned VLAN ID is not valid
in the current hostapd configuration.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Both Android's libc and glibc support _FORTIFY_SOURCE, a compiler
and libc feature which inserts automatic bounds checking into
common C functions such as memcpy() and strcpy(). If a buffer
overflow occurs when calling a hardened libc function, the
automatic bounds checking will safely shutdown the program and
prevent memory corruption.
Android is experimenting with _FORTIFY_SOURCE=3, a new fortify
level which enhances memcpy() to prevent overflowing an element
of a struct. Under the enhancements, code such as
struct foo {
char empty[0];
char one[1];
char a[10];
char b[10];
};
int main() {
foo myfoo;
int n = atoi("11");
memcpy(myfoo.a, "01234567890123456789", n);
return 0;
}
will cleanly crash when the memcpy() call is made.
Fixup hostap code to support the new level. Specifically:
* Fixup sha1_transform so it works with the enhanced bounds checking.
The old memcpy() code was attempting to write to context.h0, but that
structure element is too small and the write was extending (by design)
into h1, h2, h3, and h4. Use explicit assignments instead of
overflowing the struct element.
* Modify most of the structures in ieee802_11_defs.h to use ISO C99
flexible array members (https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html)
instead of a zero length array. Zero length arrays have zero length,
and any attempt to call memcpy() on such elements will always overflow.
Flexible array members have no such limitation. The only element not
adjusted is probe_req, since doing so will generate a compile time error,
and it's not obvious to me how to fix it.
Signed-off-by: Nick Kralevich <nnk@google.com>
wpa_ctrl.c gets sys/stat.h inherited from
private/android_filesystem_config.h it should
not rely on this in the future. The intent is
to move fs_config function into libcutils and
thus deprecate any need for sys/stat.h in this
include file.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The internal TLS implementation started rejecting number of unsupported
configuration parameters recently, but those new error paths did not
free the allocated tlsv1_credentials buffer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This function exposes internal state of the TLS negotiated parameters
for the sole purpose of being able to implement PRF for EAP-FAST. Since
tls_connection_prf() is now taking care of all TLS-based key derivation
cases, it is cleaner to keep this detail internal to each tls_*.c
wrapper implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is not needed anymore with the tls_connection_prf() being used to
handle all key derivation needs. tls_connection_get_keys() is a bit
misnamed for now, but it is only used to fetch the client and server
random for Session-Id derivation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
tls_openssl.c is the only remaining TLS/crypto wrapper that needs the
internal PRF implementation for EAP-FAST (since
SSL_export_keying_material() is not available in older versions and does
not support server-random-before-client case). As such, it is cleaner to
assume that TLS libraries support tls_connection_prf() and move the
additional support code for the otherwise unsupported cases into
tls_openssl.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
is_ht_allowed is a confusing name since this variable is used to track
whether 40 MHz channel bandwidth is allowed instead of whether HT is
allowed in general.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds hexdumps of MSCHAP/MSCHAPv2 Challenge and Response in format
used by asleap. This is only enabled for CONFIG_TESTING_OPTIONS=y
builds.
Signed-off-by: Jouni Malinen <j@w1.fi>
If NEED_AP_MLME=y is not defined, compilation might
fail under some configurations:
src/ap/drv_callbacks.c:594:2: warning: implicit declaration of
function ‘hostapd_acs_completed’ [-Wimplicit-function-declaration]
src/ap/sta_info.c:253: undefined reference to `sae_clear_retransmit_timer'
Fix these errors by adding the missing hostapd_acs_completed() stub,
and defining NEED_AP_MLME in case of CONFIG_SAE.
Signed-off-by: Eliad Peller <eliad@wizery.com>
This replaces the internal CBC mode implementation in
aes_128_cbc_encrypt() and aes_128_cbc_decrypt() with the OpenSSL
implementation for CONFIG_TLS=openssl builds.
Signed-off-by: Jouni Malinen <j@w1.fi>
The local buffers may contain information used to generate parts of the
derived key, so clear these explicitly to minimize amount of unnecessary
private key-related material in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
The local hash[] buffer may contain parts of the derived key, so clear
it explicitly to minimize number of unnecessary copies of key material
in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
The local T[] buffer may contain parts of the derived key, so clear it
explicitly to minimize number of unnecessary copies of key material in
memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previous workaround for WEXT events from the Host AP driver required
wlan# and wifi# interfaces to have fixed names with the same number.
While that used to be the common case ten years ago, it is less common
nowadays. Extend this to use sysfs (if available) to figure out the
wifi# interface name if the specified interface is detected to be using
the Host AP driver.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add SQLite error message and DB name to the DB related errors. Add
enough tracing so that users can know exactly where users are failing to
be found.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The new network profile parameter mem_only_psk=1 can be used to specify
that the PSK/passphrase for that network is requested over the control
interface (ctrl_iface or D-Bus) similarly to the EAP network parameter
requests. The PSK/passphrase can then be configured temporarily in a way
that prevents it from getting stored to the configuration file.
For example:
Event:
CTRL-REQ-PSK_PASSPHRASE-0:PSK or passphrase needed for SSID test-wpa2-psk
Response:
CTRL-RSP-PSK_PASSPHRASE-0:"qwertyuiop"
Note: The response value uses the same encoding as the psk network
profile parameter, i.e., passphrase is within double quotation marks.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends EAP-pwd peer support to allow NtHash version of password
storage in addition to full plaintext password. In addition, this allows
the server to request hashed version even if the plaintext password is
available on the client. Furthermore, unsupported password preparation
requests are now rejected rather than allowing the authentication
attempt to continue.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends EAP-pwd server support to allow NtHash version of password
storage in addition to full plaintext password.
Signed-off-by: Jouni Malinen <j@w1.fi>
Old code defaulted to WEP for an AP advertising OSEN. Show as OSEN
instead. Re-use most of the RSN parsing logic since all but the header
is the same.
Example output:
[root@ath9k-f lanforge]# ./local/bin/wpa_cli -i sta0 scan_results
bssid / frequency / signal level / flags / ssid
00:0e:8e:6f:40:49 2462 -23 [OSEN-OSEN-CCMP][ESS] ben-138
Signed-off-by: Ben Greear <greearb@candelatech.com>
HT requires QoS/WMM, so unset HT capabilities for a station
whose association request does not include a valid WMM IE.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This extends NL80211_CMD_ROAM event processing to allow the driver to
roam to another ESS (different SSID) when using offloaded BSS selection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update ACS driver offload feature for VHT configuration. In addition,
this allows the chanlist parameter to be used to specify which channels
are included as options for the offloaded ACS case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Delete all ASP serice advertisement on wpas_p2p_service_flush similarly
to Bonjour and UPnP services.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
There's off-by-one in the range availability check - the case of
first_chan_idx + num_chans == num_channels should be allowed (e.g., 0 +
1 == 1, for the case of a single 20 MHz channel).
Signed-off-by: Maital Hahn <maitalm@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
When looking for a new operating channel, consider the case of
non-contiguous channels when checking all the needed channels (e.g., the
driver might support channels 36, 38, 40, so look for channels 36+40
explicitly, instead of failing when encountering channel 38).
Signed-off-by: Eliad Peller <eliad@wizery.com>
In wiphy_info_handler(), vendor specific commands were
interpreted as QCA specific without checking for the OUI,
which caused incorrect setting of driver flags with
commands from other vendors. As a result, that could
prevent proper operation (e.g., inability to process CSA).
This patch ensures that QCA vendor specific commands are
checked against QCA OUI before related flags are set.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
If the AP/Authenticator receives an EAPOL-Key msg 2/4 for an association
that negotiated use of PSK and the EAPOL-Key MIC does not match, it is
likely that the station is trying to use incorrect PSK/passphrase.
Report this with "AP-STA-POSSIBLE-PSK-MISMATCH <STA addr>" control
interface event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
SChannel/CryptoAPI as a TLS/crypto library alternative was never
completed. Critical functionality is missing and there are bugs in this
implementation. Since there are no known plans of completing this
support, it is better to remove this code.
Signed-off-by: Jouni Malinen <j@w1.fi>
Channel 140 is needed as allowed HT40 channel pair to use
channel 144 introduced in 802.11ac for VHT40 and VHT80.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Handle NL80211_ATTR_EXT_FEATURES attribute and
NL80211_EXT_FEATURE_VHT_IBSS to determine whether
the driver supports VHT with IBSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
It was possible for bitfield_get_first_zero() to read one octet beyond
the allocated bit buffer in case the first zero bit was not within
size-1 first octets.
Signed-off-by: Jouni Malinen <j@w1.fi>
This event was previously used only when disabling AP mode operation
through hostapd control interface. Make this more consistent by
providing same indication when disabling hostapd interface through the
interface deinit path. This adds the event to the case where a full
hostapd radio instance is removed which also applies for the
wpa_supplicant AP mode operations.
Signed-off-by: Jouni Malinen <j@w1.fi>
If OpenSSL reports that a presented leaf certificate is invalid,
but it has been explicitly pinned, accept it anyway.
Signed-off-by: Rohit Agrawal <rohit.agrawal.mn@gmail.com>
Previously, it would have been possible to complete RSN connection by
skipping the msg 3/4 and 4/4 completely. This would have resulted in
pairwise key not being configured. This is obviously not supposed to
happen in practice and could result in unexpected behavior, so reject
group key message before the initial 4-way handshake has been completed.
Signed-off-by: Jouni Malinen <j@w1.fi>
ML80211_ATTR_TDLS_OPERATION can now set to NL80211_TDLS_DISCOVERY_REQ to
allow the driver to request wpa_supplicant to initiate TDLS Discovery
Request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the TDLS operation request mechanism to allow TDLS
Discovery Request to be initiated by the driver similarly to the
existing Setup and Teardown requests.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, it was possible for the wpa_sm_start_preauth() and
wpa_sm_rekey_ptk() eloop callbacks to remain active after disconnection
and potentially continue to be used for the next association. This is
not correct behavior, so explicitly cancel these timeouts to avoid
unexpected attempts to complete RSN preauthentication or to request PTK
to be rekeyed.
It was possible to trigger this issue, e.g., by running the following
hwsim test case sequence: ap_wpa2_ptk_rekey ap_ft_sae_over_ds
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The initial IEEE 802.11 ProxyARP functionality in the kernel needed
changes in behavior and that ended up requiring an independent
configuration parameter to be used. Update hostapd to use that new
proxyarp_wifi parameter instead of the earlier proxyarp.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This converts the QCA vendor event to EVENT_DFS_* events for the case
of DFS offloaded to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Modify the string for AP-CSA-FINISHED event indication to include a flag
which tells the framework whether the new channel is a DFS channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add handling logic for DFS offloaded case, and add a helper function
that takes the frequency (MHz) as a param and returns 1 if given channel
requires DFS, or 0 otherwise.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If DFS is offloaded to the driver, hostapd should not be performing
these operations. Send the relevant control interface events to provide
information to upper layer software that may use such events to track
DFS/CAC state. This makes the offloaded DFS implementation more
consistent with the DFS-in-hostapd behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces a callback to notify any configuration updates
from the eap_proxy layer. This is used to trigger re-reading of IMSI and
MNC length.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a connection with the primary server cannot be established, restore
connection to the previously used server.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 347c55e216 ('RADIUS client: Re-try
connection if socket is closed on retransmit') added a new option for
initialing RADIUS server failover from radius_client_retransmit(), but
ended up trying to change authentication servers when accounting server
was supposed to be changed due to a copy-paste issue.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the GO Negotiation Response (failure) TX status to
be processed at a point where there is no P2P timeout to continue
search. Avoid stopping the ongoing search operation by explicitly
restarting it from this callback.
Signed-off-by: Jouni Malinen <j@w1.fi>
The optional freq=<MHz> can now be used with the P2P_FIND command to
specify a single channel to scan during the first round of P2P search.
For example, this can be used to replace the full initial scan with a
single channel scan of a known operation channel.
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
This reverts commit 3df2f4fe99 ('P2P:
Remove unused P2P_SCAN_SPECIFIC') with a modification to fit the current
code base.
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
Disable VHT caps for STAs for which there is not even a single
allowed MCS in any supported number of streams. i.e STA is
advertising 3 (not supported) as VHT MCS rates for all supported
streams.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Commit 347c55e216 ('RADIUS client: Re-try
connection if socket is closed on retransmit') added a possibility of
executing RADIUS server failover change within
radius_client_retransmit() without taking into account that this
operation may end up freeing the pending message that is being
processed. This could result in use of freed memory. Avoid this by
checking whether any pending messages have been removed and if so, do
not try to retransmit the potentially freed message.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, send() was called with invalid fd = -1 in some error cases
for retransmission and this could even result in a loop of multiple such
attempts. This is obviously not going to work, so drop such attempts and
instead, try to reconnect a socket to the server if the current socket
is not valid.
In addition, initiate server failover immediately if the current socket
is not valid instead of waiting for a timeout.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the initial attempt at opening the socket connection to the RADIUS
server failed due to missing IP connectivity during startup, e.g., with
"connect[radius]: Network is unreachable", hostapd did not try to
reconnect when RADIUS messages were sent. Instead, it only reported "No
authentication server configured" even if the configuration did have a
server entry.
This was broken by commit 9ed4076673
('RADIUS client: Do not try to send message without socket') for the
initial case and the more recent fixes in RADIUS server failover cases
did not cover the initial failure case.
Signed-off-by: Jouni Malinen <j@w1.fi>
It does not look likely that the old DSA design would be added into the
internal TLS implement, so remove this otherwise dead code.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows wpa_supplicant to recover from some of the cases where
cfg80211 is unloaded and reloaded without restarting wpa_supplicant. The
netlink socket used for nl80211 events (global->nl_event) seemed to end
up in otherwise functionality state, but with all the event memberships
lost when cfg80211 gets reloaded.
There does not seem to be any clear way of determining when this has
happened, so it looks simplest to just try to re-subscribe to all the
events whenever an interface is re-enabled or added.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit e6dd8196e5 ('Work around Linux
packet socket regression') closed the workaround socket on the first
received EAPOL frame from the main packet socket. This can result in
closing the socket in cases where the kernel does not really work in the
expected way during the following initial association since
reauthentication/rekeying using EAPOL frames happens while operstate is
not dormant and as such, the frames can get delivered through the main
packet socket.
Fix this by closing the workaround socket only in case the first EAPOL
frame is received through the main packet socket. This case happens
while the interface is in dormant state and as such, is more likely to
show the more restricted case of kernel functionality.
In order to avoid processing the received EAPOL frames twice, verify a
checksum of the frame contents when receiving frames alternatively from
the main packet socket and the workaround socket.
Signed-off-by: Jouni Malinen <j@w1.fi>
These values were previously used only for sorting the scan results, but
it may be useful to provide access to the used values through the BSS
entries.
Signed-off-by: Jouni Malinen <j@w1.fi>
This modifies the BSS selection routines to calculate SNR and estimated
throughput for each scan result and then use the estimated throughput as
a criteria for sorting the results. This extends the earlier design by
taking into account higher throughput rates if both the AP and local
device supports HT20, HT40, or VHT80. In addition, the maximum rate is
restricted based on SNR.
In practice, this gives significantly higher probability of selecting
HT/VHT APs when there are multiple BSSes in the same ESS and SNR is not
low enough to prevent higher MCS use.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it somewhat easier to use CONFIG_WPA_TRACE=y build with
external programs that might not be aware of the initialization
requirement, e.g., when linking wpa_ctrl.c with a program that does not
use the os_*() wrappers.
Signed-off-by: Jouni Malinen <j@w1.fi>
This change adds the function hostapd_config_clear_wpa_psk() that
deletes an entire wpa_psk structure, making sure to follow the linked
list and to free the allocated memory of each PSK node. This helps to
prevent memory leaks when using PSKs from multiple sources and
reconfiguring the AP during runtime.
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
Configure the GO CTWindow on APstart if the driver supports it and this
parameter is set in wpa_supplicant configuration.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Read p2p_go_ctwindow (0-127 TUs) from the config file, and pass it to
the driver on GO start.
Use p2p_go_ctwindow=0 (no CTWindow) by default.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Some APs (e.g., Cisco 1260) sometimes add padding to the end of short
TDLS management packets and that can look like invalid IEs. This was
allowed on M3 and discovery packets, but not in others. Allow it for the
other packets as well, since required IEs are verified in the code
anyway.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Add fixed_freq=<0/1> network block parameter and pass it to the driver
when starting or joining an IBSS. If this flag is set, IBSS should not
try to look for other IBSS networks to merge with on different channels.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The '/usr/include/libnl3' header path is unsafe for cross-compilation.
Use pkg-config to find libnl-3.0 headers by default and alternatively,
allow LIBNL_INC=<path> to be used in .config to override.
Signed-off-by: Romain Naour <romain.naour@openwide.fr>
These were not supposed to include a newline at the end of the message
text since such formatting gets handled by tls_show_errors(). In
addition, change the message about the issuer's issuer to be more
accurate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If addition of a peer issuer certificate fails, the certs pointer would
be NULL when being passed to sk_X509_push() for peer issuer's issuer.
Fix this by skipping addition of issuer's issue if issuer addition
fails.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If addition of a peer issuer certificate fails, the certs pointer would
be NULL when being passed to sk_X509_push() for peer issuer's issuer.
Fix this by skipping addition of issuer's issue if issuer addition
fails.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When DFS offloading capability is supported by the driver, the driver
should use these events to indicate when a radar pattern has been
detected, channel availability check (CAC) has been completed, aborted
or finished after the non-occupancy period is over on a DFS channel.
Also, add a new driver.h event to be used by NL80211 to indicate CAC
Started event on a DFS channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver indicates that the interface has been disabled, assume
that all associations have been lost and remove the hostapd STA entries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
RTM_NEWLINK event without IFF_UP were processed for all related
interfaces (including VLANs and bridge). While these events may need to
be processed for other purposes, they should not end up claiming that
the main interface has been disabled, so indicate
EVENT_INTERFACE_DISABLED only if the ifname matches the first BSS ifname
for the interface. In addition, fix some of the ifup/down checks from
if_indextoname() cases to actually use the resolved ifname (namebuf)
rather than hardcoding the first configured ifname to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This uses couple of additional helper macros and prints more debug
information to make the VLAN events easier to analyze.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Sending client probe on already removed client from kernel driver does
not have any benefit and may lead unintended behavior among variable
drivers (mac80211 has a WARN_ON() that could have been triggered after
ifconfig down+up earlier when hostapd did not re-enable beaconing on
ifup). Skip this step in discussion when the kernel driver reports that
client entry is removed.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
This allows WPA2 mode AP to be re-enabled automatically after external
ifconfig down + up on a netdev used by hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a step towards enabling hostapd to restart AP mode functionality
if the interface is disabled and re-enabled, e.g., with ifconfig down
and up. This commit takes care of beaconining only which may be
sufficient for open mode connection, but not for WPA2 cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for an Action frame TX operation to be stopped in a way
that results in the TX status callback function not being called. This
could happen, e.g., when P2P_STOP_FIND was issued while waiting for PD
Response TX status. This specific case ended in leaving
p2p->send_action_in_progress set to 1 and that ending up stopping a
future TX operation when p2p_send_action_cb() gets called with
p2p->pending_action_state == P2P_NO_PENDING_ACTION.
This could result in reception of a fragmented service discovery
response failing due to the GAS sequence getting stopped when receiving
TX callback for the first GAS comeback request. That sequence could be
hit in mac80211_hwsim tests when p2p_listen_and_offchannel_tx was
followed by p2p_service_discovery_fragmentation (even after a long time
since this was on dev1 and there could be even 10 minutes between these
test cases).
Fix this issue by clearing send_action_in_progress whenever stopping
pending P2P operation with p2p_stop_find (or P2P_FLUSH for that matter).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When DFS offloading capability is supported by the driver, the driver
should use this event to indicate when channel availability check (CAC)
is started on a DFS channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds testing code (for CONFIG_TESTING_OPTIONS=y builds only) to
send an nl80211 vendor command and report a test vendor event in case
the driver supports this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not reply to a Probe Request frame with a DSSS Parameter Set element
in which the channel is different than the operating channel of the AP,
as the sending station is not found on the AP's operating channel.
IEEE Std 802.11-2012 describes this as a requirement for an AP with
dot11RadioMeasurementActivated set to true, but strictly speaking does
not allow such ignoring of Probe Request frames if
dot11RadioMeasurementActivated is false. Anyway, this can help reduce
number of unnecessary Probe Response frames for cases where the STA is
less likely to see them (Probe Request frame sent on a neighboring, but
partially overlapping, channel).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Send MESH-SAE-AUTH-BLOCKED event if SAE authentication is blocked. The
BLOCK state will finish when a new peer notification event is sent for
the same MAC address.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
SAE authentication fails likely with wrong password. This commit adds a
notification of the failure to the upper application (UI) so that the
application can notify suspection of a wrong password to the user. The
control interface monitor even for this is "MESH-SAE-AUTH-FAILURE
addr=<peer>".
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Commit 5a2a6de6a5 ('mesh: Make inactivity
timer configurable') has a problem on 32 bit systems. Setting
NL80211_MESHCONF_PLINK_TIMEOUT to 0xffffffff causes expiration of STA in
a minute by NL80211_CMD_DEL_STATION event. this is the kernel rule for
STA expiration:
(current jiffies) > (frame Rx jiffies + NL80211_MESHCONF_PLINK_TIMEOUT * 250)
On a 32 bit system, the right side could overflow and be unexpected
small value if NL80211_MESHCONF_PLINK_TIMEOUT is sufficiently large. STA
expiration occurs by this reason.
This patch solves the problem by disabling the STA expiration
functionality in mac80211. However, old kernel does not support
disabling it. If so, this patch sets mac80211 inactivity timer 60
seconds into future from the wpa_supplicant inactivity timer.
And I mis-understood that mesh_max_inactivity=0 disables inactivity
timer in wpa_supplicant. This commit fixes it also.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
If HT40 co-ex scan fails due to the driver rejecting scan triggers
multiple times, it was possible for the ap_ht40_scan_retry() timeout
being left behind and it getting run after hapd->drv_priv has been
cleared. This would result in NULL pointer dereference in
driver_nl80211_scan.c. Fix this by canceling the timeout when disabling
the interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit e6dd8196e5 ('Work around Linux
packet socket regression') added a mechanism to close the workaround
bridge socket in l2_packet_receive(). However, it did not take into
account the possibility of the l2->rx_callback() closing the l2_packet
socket altogether. This could result in use of freed memory when usin
RSN pre-authentication. Fix this by reordering the calls to clear the
workaround socket before calling the rx_callback.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, a channel with even a single scan/survey result missing
information was skipped in ACS. This may not be desirable in cases when
multiple scan iterations are used (which is the case by default in
hostapd). Instead, use all channels that provided at least one complete
set of results. Calculate the average interference factor as an average
of the iterations that did provide complete values.
This seems to help with some cases, e.g., when ath9k may not be able to
report the noise floor for all channels from the first scan iteration
immediately after the driver has been loaded, but then returns it for
all other scan iterations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new acs_chan_bias configuration parameter is a space-separated list
of <channel>:<bias> pairs. It can be used to increase (or decrease) the
likelihood of a specific channel to be selected by the ACS algorithm.
The total interference factor for each channel gets multiplied by the
specified bias value before finding the channel with the lowest value.
In other words, values between 0.0 and 1.0 can be used to make a channel
more likely to be picked while values larger than 1.0 make the specified
channel less likely to be picked. This can be used, e.g., to prefer the
commonly used 2.4 GHz band channels 1, 6, and 11 (which is the default
behavior on 2.4 GHz band if no acs_chan_bias parameter is specified).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The interference factors for adjacent 2.4 GHz channels were summed
together without doing any kind of weighted average on them. This
resulted in the channels at the band edges getting undue preference due
to only including interference factors from three channels vs. five for
the channels in the middle of the band.
While it is somewhat unclear whether the design here was supposed to
count overlapping channels together in this way or whether that is
already covered in channel survey results, it is clear that this summing
of three to five values together and then comparing the sum rather than
average of some kind gives too much preference to the channels at the
edges of the band by assuming that there is no interference whatsoever
outside the band.
Use weighted average of the interference factors rather than a sum from
different number of values. For now, the adjacent 2.4 GHz channels get
weight of 0.85 (1.0 for the main channel itself) and the neighboring
channels to those adjacent ones get 0.55 weight. Band-edge channels are
handled in a way that takes average over the channels that were actually
considered instead of assuming zero interference from neighboring bands.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If p2p_find_timeout triggers after starting SD but before getting TX
status for send action, unwanted search could get triggered again when
TX status arrives though p2p_find_timeout moved the state to P2P_IDLE by
then. p2p_continue_find() would then move the state to P2P_SEARCH again.
Do not trigger the find operation from this context if state is
P2P_IDLE to avoid this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is going to be required for OpenSSL 1.1.0 which makes the SSL
structure opaque. Older versions starting from OpenSSL 1.0.1 include
this function, so start using it now based on OPENSSL_VERSION_NUMBER.
Signed-off-by: Jouni Malinen <j@w1.fi>
OpenSSL 0.9.8 and newer includes SSL_CTX_get_cert_store() and
SSL_CTX_set_cert_store() helper functions, so there is no need to
dereference the SSL_CTX pointer to cert ssl_ctx->cert_store. This helps
in working with the future OpenSSL 1.1.0 release that makes the SSL_CTX
structure opaque.
Signed-off-by: Jouni Malinen <j@w1.fi>
