With multiple interface like AP and station which is already
associated to some other AP, when we try to do channel switch
for the AP mode (different from the operation channel support of
station) and if the AP channel switch fails continously (including
the fallback channel switch), results in a crash due to NULL pointer
dereference. This is because hostapd_deinit_driver() assigns the
driver context (drv_priv) to NULL as we are not able to bring up
the interface with a new channel
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Add attribute for TA max duration after last TA received. So that local
time is synchromous to other communicating OCB STAs. If the duration
expires, OCB STA without UTC time source is not in sync to other STAs
and stop scheduling DSRC channel switch after max duration.
Signed-off-by: Zhaoyang Liu <zhaoyang@codeaurora.org>
Signed-off-by: Ferry Zhou <tianguiz@codeaurora.org>
Document QCA vendor OCB commands about IEEE Std 802.11 communication
outside the context of a basic service set. Also define all attributes
for the specific OCB commands.
Signed-off-by: Zhaoyang Liu <zhaoyang@codeaurora.org>
Signed-off-by: Ferry Zhou <tianguiz@codeaurora.org>
This change fixes the following compilation error:
wpa.c:2465: error: undefined reference to 'crypto_ecdh_deinit'
in builds where CONFIG_ECC does not get defined.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes the following compiler warning:
wpa_auth.c:4249:34: error: address of array 'a->conf.fils_cache_id'
will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not accept a link-local IPv4 address when waiting for a valid DHCP
address. This helps with hs20-osu-client use cases where DHCP response
has not yet been received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the Value node was not added if value of a node could not be
fetched. This can cause interoperability issues, so address that in the
same way as an empty length value, i.e., by adding a Value node with
zero-length contents.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In case wpa_supplicant is using driver_macsec_linux, but macsec module
is not (yet) loaded in the kernel, nl_socket_alloc() fails and drv->sk
is NULL. In this case, don't call libnl functions rntl_link_add() or
rtnl_link_change() using such NULL pointer, to prevent program from
getting segmentation faults like:
Program received signal SIGSEGV, Segmentation fault.
nl_socket_get_local_port (sk=sk@entry=0x0) at socket.c:365
365 if (sk->s_local.nl_pid == 0) {
(gdb) p sk
$1 = (const struct nl_sock *) 0x0
(gdb) bt
#0 nl_socket_get_local_port (sk=sk@entry=0x0) at socket.c:365
#1 0x00007ffff79c56a0 in nl_complete_msg (sk=sk@entry=0x0,
msg=msg@entry=0x55555595a1f0) at nl.c:491
#2 0x00007ffff79c56d1 in nl_send_auto (sk=sk@entry=0x0,
msg=msg@entry=0x55555595a1f0) at nl.c:522
#3 0x00007ffff79c652f in nl_send_sync (sk=sk@entry=0x0,
msg=0x55555595a1f0) at nl.c:556
#4 0x00007ffff755faf5 in rtnl_link_add (sk=0x0,
link=link@entry=0x55555595b0f0, flags=flags@entry=1024) at route/link.c:1548
#5 0x000055555567a298 in macsec_drv_create_transmit_sc (priv=0x55555593b130,
sc=0x55555593b320, conf_offset=<optimized out>) at ../src/drivers/driver_macsec_linux.c:998
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
ieee802_1x_kay_deinit_transmit_sc() frees the transmit secure channel
data, but secy_delete_transmit_sc() still needs it. Since this functions
are called sequentially, secy_delete_transmit_sc() can be called from
ieee802_1x_kay_deinit_transmit_sc() before txsc is freed.
Fixes: 128f6a98b3 ("mka: Fix the order of operations in secure channel deletion")
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
ieee802_1x_kay_deinit_receive_sc() frees the receive secure channel data,
but secy_delete_receive_sc() still needs it. Since these two functions
are always called sequentially, secy_delete_receive_sc() can be called
from ieee802_1x_kay_deinit_receive_sc() before rxsc is freed.
Fixes: 128f6a98b3 ("mka: Fix the order of operations in secure channel deletion")
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
1. Add new attribute to report corresponding antenna information to the
chain RSSI which is used in subcmd
QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI.
2. Add a series of attr to support the new wmi interface
WMI_PDEV_PARAM_ANT_DIV_USRCFG which export parameters setting of antenna
diversity algorithm to userspace.
Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY is added to set
propagation delay's absolute value. This is a more detailed version of
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY.
Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
If a P2P_FIND command is issued for running the initial full scan and
the attempt to start that full scan fails, the previous behavior was to
wait for the ongoing scan to complete and then continue p2p_find scan
iterations. However, this continued with the social channels scan
instead of the initial full scan. This could end up missing the full
scan completely.
Fix this by marking the full scan pending if the new scan cannot be
started immediately. Then start the initial full scan after the ongoing
scan completes before moving to social channel only scan iterations.
This applies both for the P2P_FIND_START_WITH_FULL (no specific
frequency set) and P2P_FIND_PROGRESSIVE cases since both of them start
with a single full scan round.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the "P2P_FIND freq=<MHz>" operation more robust by continuing
to include the specified frequency in the consecutive scan rounds
instead of including it only once in the first scan. In other words, the
first scan is only for the specified frequency just like the previous
behavior, but the following scans include all the social channels and
the specified frequency instead of just the previously used social
channels.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds an option to configure wpa_supplicant to use the perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime network profile parameter fils_dh_group is used to enable
this by specifying which DH group to use. For example, fils_dh_group=19
would use FILS SK PFS with a 256-bit random ECP group.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds an option to configure hostapd to enable use of perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime configuration parameter fils_dh_group is used to enable this
by specifying which DH group to use. For example, fils_dh_group=19 would
allow FILS SK PFS to be used with a 256-bit random ECP group.
Signed-off-by: Jouni Malinen <j@w1.fi>
draft-harkins-owe-07.txt does not specify these parameters, so need to
pick something sensible to use for the experimental implementation. The
Suite B 128-bit level AKM 00-0F-AC:11 has reasonable parameters for the
DH group 19 case (i.e., SHA256 hash), so use it for now. This can be
updated if the OWE RFC becomes clearer on the appropriate parameters
(KEK/KCK/MIC length, PRF/KDF algorithm, and key-wrap algorithm).
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds STA side addition of OWE Diffie-Hellman Parameter element into
(Re)Association Request frame and processing it in (Re)Association
Response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds AP side processing for OWE Diffie-Hellman Parameter element in
(Re)Association Request frame and adding it in (Re)Association Response
frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
The KDF define in RFC 5295 is very similar to HKDF-Expand() defined in
RFC 5869. Allow a NULL label to be used to select the RFC 5869 version
with arbitrary seed (info in RFC 5869) material without forcing the
label and NULL termination to be included. HKDF-Expand() will be needed
for OWE.
Signed-off-by: Jouni Malinen <j@w1.fi>
These allow ECDH to be used with compressed public key encoding (only
x-coordinate). This is needed for FILS PFS and OWE.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a helper function that parses candidate list from command line
arguments.
This function will be used (in the following commits) to add
a candidate list to BSS transition management query.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This extends the GAS/ANQP parser in wpa_supplicant to process MBO
ANQP-elements and indicate received Cellular Data Connection Preference
values over the control interface.
When a valid MBO ANQP-element is received, the following control
interface message is sent:
RX-MBO-ANQP <BSSID> cell_conn_pref=<value>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the GAS server to process MBO ANQP-elements and reply to a
query for the Cellular Data Connection Preference (if configured). The
new configuration parameter mbo_cell_data_conn_pref can be used to set
the value (0, 1, or 255) for the preference to indicate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
MBO techspec v0.0_r27 changed the MBO ANQP-element format. The MBO
element in ANQP query should now include an MBO Query List element that
contains a list of MBO elements to query.
Add API to add the MBO Query List to an ANQP query.
Format:
ANQP_GET <addr> <info_id>[,<info_id>]...[,mbo:<subtype>...]
Example for querying neighbor report with MBO cellular data
connection preference:
ANQP_GET <bssid> 272,mbo:2
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
As FCC DFS requirement does not explicitly mention about the validity of
the (pre-)CAC when channel is switched, it is safe to assume that the
pre-CAC result will not be valid once the CAC completed channel is
switched or radar detection is not active on the (CAC completed) channel
within a time period which is allowed (10 seconds - channel switch time)
as per FCC DFS requirement.
Use the new driver event to allow the driver to notify expiry of the CAC
result on a channel. Move the DFS state of the channel to 'usable' when
processing pre-CAC expired event. This means any future operation on
that channel will require a new CAC to be completed. This event is
applicable only when DFS is not offloaded to the kernel driver.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Process the new nl80211 event NL80211_RADAR_PRE_CAC_EXPIRED to allow the
driver to notify expiry of the CAC result on a channel.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
When DFS channel state is shared across multiple radios on the system it
is possible that a CAC completion event is propagated from other radio
to us. When in enabled state, do not proceed with setup completion upon
processing CAC completion event with devices where DFS is not offloaded,
when in state other than enabled make sure the configured DFS channel is
in available state before start the AP.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
The userspace may want to delay the the first scheduled scan.
This enhances sched_scan to add initial delay (in seconds) before
starting first scan cycle. The driver may optionally choose to
ignore this parameter and start immediately (or at any other time).
This uses NL80211_ATTR_SCHED_SCAN_DELAY to add this via user
global configurable option: sched_scan_start_delay.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This leads to cleaner code overall, and also reduces the size
of the hostapd and wpa_supplicant binaries (in hwsim test build
on x86_64) by about 2.5 and 3.5KiB respectively.
The mechanical conversions all over the code were done with
the following spatch:
@@
expression SIZE, SRC;
expression a;
@@
-a = os_malloc(SIZE);
+a = os_memdup(SRC, SIZE);
<...
if (!a) {...}
...>
-os_memcpy(a, SRC, SIZE);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used to clean the code and reduce size by converting
os_malloc() followed by os_memcpy() cases to use a single function call.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add driver interface command using the QCA vendor extensions to check
the driverr whether to accept or reject a BSS transition candidate. For
the reject case, report an MBO reject reason code.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
radius_server_session_free() does not remove the session from the
session list and these radius_server_get_new_session() error paths ended
up leaving a pointer to freed memory into the session list. This
resulted in the following operations failing due to use of freed memory.
Fix this by using radius_server_session_remove() which removes the entry
from the list in addition to calling radius_server_session_free().
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible to hit a double-free on the l2_packet socket if
initialization of DHCP/NDISC snoop failed on a hostapd interface that
had previously had those enabled successfully. Fix this by clearing the
l2_packet pointers during deinit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT for setting the number
of antennas that will be active in different modes for each connection.
Signed-off-by: Alexei Avshalom Lazar <qca_ailizaro@qca.qualcomm.com>
Define a new attribute QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH.
This attribute can set a station device to work in 5 or 10 MHz channel
width while in disconnect state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd.conf parameter country3 can now be used to configure the
third octet of the Country String that was previously hardcoded to ' '
(= 0x20).
For example:
All environments of the current frequency band and country (default)
country3=0x20
Outdoor environment only
country3=0x4f
Indoor environment only
country3=0x49
Noncountry entity (country_code=XX)
country3=0x58
IEEE 802.11 standard Annex E table indication: 0x01 .. 0x1f
Annex E, Table E-4 (Global operating classes)
country3=0x04
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When ASLR is enabled, like it is by default on many distros now,
the trace code doesn't work right.
Fix this by looking up the start of the executable mapping and
subtracing it from all the lookups.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
CONFIG_TLS=linux can now be used to select the crypto implementation
that uses the user space socket interface (AF_ALG) for the Linux kernel
crypto implementation. This commit includes some of the cipher, hash,
and HMAC functions. The functions that are not available through AF_ALG
(e.g., the actual TLS implementation) use the internal implementation
(CONFIG_TLS=internal).
Signed-off-by: Jouni Malinen <j@w1.fi>
These operations may fail with some crypto wrappers, so allow the
functions to report their results to the caller.
Signed-off-by: Jouni Malinen <j@w1.fi>
When getting the channel number from a frequency, all supported modes
should be checked rather than just the current mode. This is needed when
hostapd switches to a channel in different band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The __FAVOR_BSD macro was previously used in netinet/udp.h to select
between two different names of the variables in struct udphdr. Define
that to force the versions with the uh_ prefix. In addition, use the
same style consistently within fils_hlp.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new broadcast_deauth parameter can be used to disable sending of the
Deauthentication frame whenever AP is started or stopped. The default
behavior remains identical to the past behavior (broadcast_deauth=1).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 01e2231fdc ('hostapd: Skip some
configuration steps for mesh cases') removed some operations based on
hapd->iface->mconf being NULL. This was within #ifdef CONFIG_MESH, so it
should not impact hostapd, but it can impact AP mode with
wpa_supplicant. That does not sound intentional, so make these
conditional on hapd->conf->mesh being enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows PMKSA cache entries for FILS-enabled BSSs to be shared
within an ESS when the BSSs advertise the same FILS Cache Identifier
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The RSN supplicant implementation needs to be updated to use the new
BSSID whenever doing FILS authentication. Previously, this was only done
when notifying association and that was too late for the case of
reassociation. Fix this by providing the new BSSID when calling
fils_process_auth(). This makes PTK derivation use the correct BSSID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows PMKSA cache entries to be shared between all the BSSs
operated by the same hostapd process when those BSSs use the same FILS
Cache Identifier value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The correct order of deleting a secure channel is to purge all the
secure associations in the channel before actually deleting the secure
channel.
Signed-off-by: Badrish Adiga H R <badrish.adigahr@gmail.com>
The RSN pre-authentication case ended up ignoring the initial
startPeriod value and delayed EAPOL-Start message by two seconds. Fix
this by forcing the first EAPOL-Start message to be sent when running
pre-authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds reason for timeout in event CTRL-EVENT-ASSOC-REJECT whenever
connection failure happens because of timeout. This extends the
"timeout" parameter in the event to include the reason, if available:
timeout=scan, timeout=auth, timeout=assoc.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE 802.11ax HE changes to include HE IEs in Beacon and Probe Response
frames. These elements are using vendor specific forms for now since the
IEEE 802.11ax draft is not yet finalized and the element contents is
subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add IEEE 802.11ax definitions for config, IEEE structures, and
constants. These are still subject to change in the IEEE process.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Let mesh STA A be a STA which has config disable_ht=0 and disable_vht=1.
Let mesh STA B be a STA which has config disable_ht=0 and disable_vht=0.
The mesh STA A and B was connected.
Previously, the mesh STA A sent frame with VHT rate even though its VHT
was disabled. This commit fixes the issue by checking the local BSS VHT
configuration.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Let mesh STA A be a STA which has config disable_ht=1.
Let mesh STA B be a STA which has config disable_ht=0.
The mesh STA A and B was connected.
Previously, the mesh STA A sent frame with HT rate even though its HT
was disabled. This commit fixes the issue by checking the local BSS HT
configuration.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This function is called only from locations within ifdef
CONFIG_EAP_PROXY, so there is no need to try to cover the not-defined
case here and the function can simply be removed completely if
CONFIG_EAP_PROXY=y is not used.
Signed-off-by: Jouni Malinen <j@w1.fi>
This debug print can include GTK and IGTK, so use wpa_hexdump_key()
instead of wpa_hexdump() for it to avoid undesired exposure of keys in
debug log.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While the FILS authentication cases were already using the proper PMK
length (48 octets instead of the old hardcoded 32 octet), the initial
association case had not yet been updated to cover the new FILS SHA384
AKM and ended up using only a 32-octet PMK. Fix that to use 48-octet PMK
when using FILS SHA384 AKM.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
sha384_prf() is used both with Suite B and FILS, so add CONFIG_FILS as
another alternative to building in this functionality.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a copy of the internal HMAC-SHA256 implementation with the hash
block size and output length updated to match SHA384 parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
The output length was incorrect (32 from the copy-pasted SHA256
version). Fix this to return the correct number of octets (48) for
SHA384. This fixes incorrect key derivation in FILS when using the
SHA384-based AKM.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
HTTP response was previously sent as a plaintext without the HTTP header
on port 12345. By default Android webview/Chrome assumes plaintext as
HTTP/0.9 data. Android webview/Chrome has removed support of HTTP/0.9
request/response on non-standard ports, i.e., other than port 80. This
results in error while opening URL 'http://localhost:12345/'.
Fix this by prefixing the HTTP response with the HTTP/1.1 header.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously the peer operating channel preference was accepted if the
indicated frequency was listed in the local preference list from the
driver. This was assuming that the driver included only channels that
are currently enabled for GO operation. Since that might not be the
case, filter the local preference list by doing an explicit validation
of the indicated channels for P2P support.
This moves the similar validation steps from two other code paths in
p2p_check_pref_chan_recv() and p2p_check_pref_chan_no_recv() into a
common filtering step in p2p_check_pref_chan() for all three cases.
This avoids issues to start the GO in cases where the preferred
frequency list from the driver may include channels that are not
currently enabled for P2P GO use (e.g., 5 GHz band in world roaming
configuration).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new P2P_SET parameter uses <op_class>:<channel> format and is used
mainly for testing purposes to allow overriding the value of the GO
Negotiation Response frame Operating Channel attribute.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, any potential (even if very unlikely) local operation error
was ignored. Now these will result in aborting the negotiation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The url argument to ieee802_11_send_bss_trans_mgmt_request() was
hardcoded to NULL in the only caller, so this code cannot be reached.
wnm_send_bss_tm_req() construct the same frame with more generic
parameters, including option for including the URL, so
ieee802_11_send_bss_trans_mgmt_request() can be simplified.
Signed-off-by: Jouni Malinen <j@w1.fi>
The length of the WNM-Sleep element was not verified before using it.
This could result in reading the subfields in this element (total of
four octets) beyond the end of the buffer. Fix this by ignoring the
element if it is not long enough to contain all the subfields.
Signed-off-by: Jouni Malinen <j@w1.fi>
The struct wpa_stsl_negotiation seemed to have been for some kind of
tracking of state of PeerKey negotiations within hostapd. However,
nothing is actually adding any entries to wpa_auth->stsl_negotiations or
using this state. Since PeerKey does not look like something that would
be deployed in practice, there is no justification to spend time on
making this any more complete. Remove the dead code now instead of
trying to figure out what it might be used for.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the int medium_time variable to overflow, so use a
64-bit unsigned integer to get a large enough value for the
multiplication.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add driver interface support to set sched_scan relative RSSI parameters
and to indicate driver support for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Issue: When 2 peers are running MACsec in PSK mode with CA
established, if the interface goes down and comes up after
time > 10 seconds, CA does not get re-established.
Root cause: This is because retry_count of both the peers
would have reached MAX_RETRY_CNT and stays idle for other to
respond. This is clear deadlock situation where peer A waits
for MKA packets from peer B to wake up and vice-versa.
Fix: If MACsec is running in PSK mode, we should send MKPDUs
forever for every 2 seconds.
Signed-off-by: Badrish Adiga H R <badrish.adigahr@gmail.com>
EAP-TTLS/PEAP/FAST were previously doing this for init_for_reauth(), but
not for deinit_for_reauth(). Add the deinit_for_reauth() call as well to
cover cases like EAP-AKA cleaup of AT_CHECKCODE data.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds the same changes to EAP-AKA that were previous done for
EAP-SIM to allow functionality within an EAP-TTLS/PEAP/FAST tunnel
without causing issues to the phase 1 identity string.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The "anonymous_identity" configuration field has more than one
semantic meaning. For tunneled EAP methods, this refers to the
outer EAP identity. For EAP-SIM, this refers to the pseudonym
identity. Also, interestingly, EAP-SIM can overwrite the
"anonymous_identity" field if one is provided to it by the
authenticator.
When EAP-SIM is tunneled within an outer method, it makes sense
to only use this value for the outer method, since it's unlikely
that this will also be valid as an identity for the inner EAP-SIM
method. Also, presumably since the outer method protects the
EAP-SIM transaction, there is no need for a pseudonym in this
usage.
Similarly, if EAP-SIM is being used as an inner method, it must
not push the pseudonym identity using eap_set_anon_id() since it
could overwrite the identity for the outer EAP method.
Signed-off-by: Paul Stewart <pstew@google.com>
Add an internal flag which indicates to tunneled EAP methods (FAST,
PEAP, TTLS) that they should cache decrypted EAP-SIM/AKA/AKA' requests.
This allows EAP-SIM/AKA/AKA' to be tunneled within these outer methods
while using an external SIM authenticator over the control interface.
Signed-off-by: Paul Stewart <pstew@google.com>
There is no need to maintain different return paths for STA being
completely not present and not authorized, so merge these into a single
case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This 16-bit field uses little endian encoding and it must be read with
WPA_GET_LE16() instead of assuming host byte order is little endian. In
addition, this could be misaligned, so using a u16 pointer here was not
appropriate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hapd->acl_cache and hapd->acl_queries were not reset back to NULL in
hostapd_acl_deinit() when cached results and pending ACL queries were
freed. This left stale pointers to freed memory in hapd. While this was
normally followed by freeing of the hapd data, it is possible to re-use
that hapd when disabling and re-enabling an interface. That sequence
could result in use of freed memory if done while there were cached
results or pending ACL operations with a RADIUS server (especially, if
that server did not reply).
Fix this by setting hapd->acl_queries to NULL when the pending entries
are freed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The "!wpabuf_resize(...) == 0" condition does not make any sense. It
happens to work, but this is really supposed to simple check with
wpabuf_resize() returns non-zero and "wpabuf_resize(...)" is the
cleanest way of doing so.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for specifying a random TA for management frame
transmission commands and driver capability flags for indicating whether
this is supported in not-connected and connected states.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the OSU Providers configuration was invalid (included osu_server_uri
but not osu_method_list), it was possible for the GAS response
generation to hit a NULL dereference. Fix this by checking for the
invalid configuration before trying to fill in the OSU methods.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It can happen if the station is unreachable or sleeping longer than
the actual total GTK rekey timeout. To fix the latter case
wpa_group_update_count may be increased.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
wpa_group_update_count and wpa_pairwise_update_count can now be used to
set the GTK and PTK rekey retry limits (dot11RSNAConfigGroupUpdateCount
and dot11RSNAConfigPairwiseUpdateCount). Defaults set to current
hardcoded value (4).
Some stations may suffer from frequent deauthentications due to GTK
rekey failures: EAPOL 1/2 frame is not answered during the total timeout
period of currently ~3.5 seconds. For example, a Galaxy S6 with Android
6.0.1 appears to go into power save mode for up to 5 seconds. Increasing
wpa_group_update_count to 6 fixed this issue.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
Issue:
------
The test setup has 2 peers running MACsec in PSK mode, Peer A with
MAC address higher than MAC Address of peer B. Test sequence is
1. Peer B starts with actor_priority 255
2. Peer A starts with priority 16, becomes key server.
3. Peer A stops..
4. Peer A restarts with priority 255, but because of the stale values
participant->is_key_server(=TRUE) and participant->is_elected(=TRUE)
it continues to remain as Key Server.
5. For peer B, key server election happens and since it has lower MAC
address as compared to MAC address of A, it becomes the key server.
Now we have 2 key servers in CA and is not correct.
Root-cause & fix:
-----------------
When number of live peers become 0, the flags such lrx, ltx, orx,
otx, etc. need to be cleared. In MACsec PSK mode, these stale values
create problems while re-establishing CA.
Signed-off-by: Badrish Adiga H R <badrish.adigahr@gmail.com>
API ieee802_1x_mka_decode_dist_sak_body() wrongly puts
participant->to_use_sak to TRUE, if Distributed SAK Parameter Set of
length 0 is received. In MACsec PSK mode, this stale incorrect value can
create problems while re-establishing CA. In MACsec PSK mode, CA goes
down if interface goes down and ideally we should be able to
re-establish the CA once interface comes up.
Signed-off-by: Badrish Adiga H R <badrish.adigahr@gmail.com>
Some channels fail to be set, when falling back to 20 MHz, due to
remaining VHT info of center freq. As we are going to 20 MHz, reset the
VHT center frequency segment information as well.
Signed-off-by: Eduardo Abinader <eduardoabinader@gmail.com>
Following commit a70cd0db87 ('Don't
register for Beacon frames for IEEE 802.11ad AP'),
nl80211_get_wiphy_data_ap() is unconditionally called when starting AP.
This function tries to register for Beacon frames RX which fails for
some driver which don't support such registration and do not need it in
case the driver implements AP mode SME functionality.
Fix this by conditionally calling nl80211_get_wiphy_data_ap() like prior
to commit a70cd0db87.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Commit 91d91abf6f ('FILS: DHCP relay for
HLP requests') added steps that are conditional on sta->fils_hlp_resp
being non-NULL. One of these cases within send_assoc_resp() was properly
protected from sta == NULL error case (that is now possible after a
recent DMG change), but the first one was not. A DMG error case in a
CONFIG_FILS=y build could have hit a NULL pointer dereference here. Fix
this by verifying sta != NULL more consistently.
Signed-off-by: Jouni Malinen <j@w1.fi>
While the key derivation steps are not expected to fail, this was
already done on the AP side, so do the same in the STA side.
Signed-off-by: Jouni Malinen <j@w1.fi>
P802.11i/D3.0 described the Key Length as having value 16 for the group
key handshake. However, this was changed to 0 in the published IEEE Std
802.11i-2004 amendment (and still remains 0 in the current standard IEEE
Std 802.11-2016). We need to maintain the non-zero value for WPA (v1)
cases, but the RSN case can be changed to 0 to be closer to the current
standard.
Signed-off-by: Jouni Malinen <j@w1.fi>
While the IEEE Std 802.11-2016 is still indicating that GNonce would be
exchanged in EAPOL-Key messages (see, e.g., Figure 12-52 showing the
Send EAPOL-Key operation in the REKEYNEGOTIATING state or the sample
group key handshake in Figure 12-47), there are also examples of
describing this field as having value zero (e.g., 12.7.7.2 Group key
handshake message 1).
GNonce is used only with the Authenticator and the Supplicant does not
have any use for it, so it is better not to expose that internal value.
Hardcode the Key Nonce field to 0 in EAPOL-Key group message 1/2.
Signed-off-by: Jouni Malinen <j@w1.fi>
sm->Pair needs to be initialized to TRUE since unicast cipher is
supported and this is an ESS. However, the normal place for setting this
(WPA_PTK::INITIALIZE) is skipped with using FT protocol or FILS
authentication, so need to do that separately when forcing PTKINITDONE.
Signed-off-by: Jouni Malinen <j@w1.fi>
The local custom version of allocating and initializing struct
hostapd_data within wpa_supplicant_mesh_init() is problematic. This has
already missed couple of initialization steps that are required. Instead
of trying to remember to keep this up to date, use
hostapd_alloc_bss_data() so that there is only one place for this
initialization.
This is fixing a recent issue where FILS HLP started using
hapd->dhcp_server and expected that to be initialized to -1. For the
mesh case, that did not happen and when removing the interface, the FILS
HLP implementation ended up unregistering eloop socket for
hapd->dhcp_server (= 0). This could result in missing socket callbacks
for an arbitrary socket.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use the defines for vht_oper_chwidth values more consistently in
hostapd_set_freq_params() to make this more readable.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit introduces the vendor command to set the trace level
for the respective QCA host driver module.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The hostapd processing of the AES-SIV AAD was incorrect. The design for
the AAD changed between P802.11ai/D7.0 and D8.0 from a single vector
with concatenated data to separate vectors. The change in the
implementation had missed the change in the aes_siv_decrypt() call for
the num_elem parameter. This happened to work with the mac80211
implementation due to a similar error there.
Fix this by using the correct numbers of vectors in the SIV AAD so that
all the vectors get checked. The last vector was also 14 octets too long
due to incorrect starting pointer, so fix that as well. The changes here
are not backwards compatible, i.e., a similar fix in the Linux mac80211
is needed to make things interoperate again.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While RFC 5295 uses "8" as the value to use in the length field in KDF
context when deriving EMSKname, it is clearer to use the macro defining
EMSKname as the value since the KDF design in RFC 5295 encodes the
length of the derived data in octets in that part of the context data.
This change is just making the implementation easier to understand while
not actually changing the behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Unlike the EMSKname and rRK derivations, rIK derivation is actually
using the "optional data" component in the context data (see RFC 5295).
RFC 6696 defines that optional data to be the cryptosuite field for rIK.
This was missing from the previous implementation and that resulted in
incorrect rIK being derived.
In addition, the rIK Label string does not actually include the "EAP "
prefix in the way as the rRK Label in RFC 6696 does. This would also
have resulted in incorrect rIK value.
Fix rIK derivation by adding the cryptosuite value into the KDF context
data and fixing the label string. This change is not backwards
compatible and breaks all ERP use cases (including FILS shared key
authentication) with older (broken) and new (fixed)
hostapd/wpa_supplicant builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new FILS-HLP-RX control interface event is now used to report
received FILS HLP responses from (Re)Association Response frame as a
response to the HLP requests configured with FILS_HLP_REQ_ADD.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new dhcp_server configuration parameter can now be used to configure
hostapd to act as a DHCP relay for DHCPDISCOVER messages received as
FILS HLP requests. The dhcp_rapid_commit_proxy=1 parameter can be used
to configure hostapd to convert 4 message DHCP exchange into a 2 message
exchange in case the DHCP server does not support DHCP rapid commit
option.
The fils_hlp_wait_time parameter can be used to set the time hostapd
waits for an HLP response. This matches the dot11HLPWaitTime in IEEE Std
802.11ai-2016.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is independent functionality from the core IEEE 802.11 management
handling and will increase significantly in size, so it is cleaner to
maintain this in a separate source code file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not depend on undefined behavior with pointer arithmetic when
checking whether there is sufficient room for an option.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These can be reused for other purposes than just the DHCP snoofing for
Proxy ARP. In addition, use more complete definition of the parameters
based on the current IANA registry.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Introduce definitions for QCA vendor specific subcommands and attributes
for fetching BSS transition status.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
With device_ap_sme disabled, ACL was checked upon authentication
request. In 802.11ad there is no authentication phase so need to check
ACL upon association.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Previously, the temporary STA session timeout was set to 5 seconds. If
gas_comeback_delay is configured to be longer than 5 seconds, GAS
Comeback Response frame can't include queried information as all pending
data has already been cleared due to session timeout. This commit
resolves the issue by setting session timeout to be larger than
gas_comeback_delay.
Signed-off-by: Daniel Kim <kimdan@qca.qualcomm.com>
This commit introduces QCA vendor commands and the corresponding
attributes to set/get NUD (Network Unreachability Detection) statistics.
The set NUD statistics configures the requisite parameters to the host
driver and thereby triggers the start/stop of collection of statistics.
The get stats fetches the statistics collected in the host driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If vendor_scan_cookie is set to 0 after the scan_abort due to the scan
timeout ends in a cookie mismatch when processing the following
QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE indication. This ends up considering
the scan results as being for an external scan and thus the current
ongoing scan is not removed from the radio_work. Hence, do not reset
this vendor_scan_cookie after the scan abort so that the scan completion
event gets processed properly and vendor_scan_cookie gets cleared at
that point.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the keychain holds additional certificates other than the end
certificate, read them into the certificate chain.
Signed-off-by: Paul Stewart <pstew@google.com>
We can only send module specific messages to syslog and not debug
messages printed with wpa_printf. Add an extra command line parameter
'-s' to allow it. The feature is enabled with compile flag
CONFIG_DEBUG_SYSLOG as for wpa_supplicant and behaves in the same manner
as the wpa_supplicant -s command line argument.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Instead of copying the struct wpa_auth_callbacks, just keep a pointer to
it, keep the context pointer separate, and let the user just provide a
static const structure. This reduces the attack surface of heap
overwrites, since the function pointers move elsewhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This functionality can be used outside wpa_set_disable_ht40(), so move
the generic part to a helper function.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This adds parsing of received FILS HLP requests from (Re)Association
Request frames. The reassembled requests are verified to be in valid
format and are printed in debug output. However, actual processing or
forwarding of the packets is not yet implemented, i.e., the vendor
specific frame filtering logic is for now practically dropping all HLP
requests.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant control interface commands FILS_HLP_REQ_FLUSH and
FILS_HLP_REQ_ADD can now be used to request FILS HLP requests to be
added to the (Re)Association Request frame whenever FILS authentication
is used.
FILS_HLP_REQ_ADD parameters use the following format:
<destination MAC address> <hexdump of payload starting from ethertype>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of an unnecessary duplication of the definitions since all
the code has now been moved to using the earlier RSN_CIPHER_SUITE_*
definitions.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds the cipher suite selector values for ciphers that are not
really used with RSN, but are needed to be able to replace
WLAN_CIPHER_SUITE_* definitions with RSN_CIPHER_SUITE_*.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of an unnecessary duplication of the definitions since all
the code has now been moved to using the earlier RSN_AUTH_KEY_MGMT_*
definitions.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE 802.11 standard defines the suite selectors in <OUI>:<subtype>
format where OUI uses hexadecimal format and subtype decimal format.
These WLAN_AKM_SUITE_* definitions ended up getting written incorrectly
by interpretting the decimal part as hexadecimal and as such, by having
an incorrect value. However, the older RSN_AUTH_KEY_MGMT_* values were
defined with correct values and those definitions were used in most
locations.
This commit fixes the AKM suite selector values in RADIUS WLAN-AKM-Suite
attribute for FILS and Suite B. In addition, the AKM values used in
nl80211 driver configuration (NL80211_ATTR_AKM_SUITES) are fixed for the
Suite B cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit defines a QCA vendor command
QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE that carries required
information leading to the power save failure. This will be an event
from the host driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces the QCA vendor command and the attributes which
facilitate the host driver to use an external user space entity for
performing automatic channel selection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These commnds are mesh version of PMKSA_GET/ADD commands. So the usage
and security risk is similar to them. Refer to
commit 3459381dd2 ('External persistent
storage for PMKSA cache entries') also.
The MESH_PMKSA_GET command requires peer MAC address or "any" as an
argument and outputs appropriate stored PMKSA cache. And the
MESH_PMKSA_ADD command receives an output of MESH_PMKSA_GET and re-store
the PMKSA cache into wpa_supplicant. By using re-stored PMKSA cache,
wpa_supplicant can skip commit message creation which can use
significant CPU resources.
The output of the MESH_PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <expiration in seconds>
The example of MESH_PMKSA_ADD command is this.
MESH_PMKSA_ADD 02:00:00:00:03:00 231dc1c9fa2eed0354ea49e8ff2cc2dc cb0f6c9cab358a8146488566ca155421ab4f3ea4a6de2120050c149b797018fe 42930
MESH_PMKSA_ADD 02:00:00:00:04:00 d7e595916611640d3e4e8eac02909c3c eb414a33c74831275f25c2357b3c12e3d8bd2f2aab6cf781d6ade706be71321a 43180
This functionality is disabled by default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Relational operators (==) have higher precedence than the ternary
conditional in C. The last_subtype check for association/reassociation
was broken due to incorrect assumption about the precedence. Fix this by
adding parenthesis around the ternary conditional.
The previous implementation worked for Association Request frames by
accident since WLAN_FC_STYPE_ASSOC_REQ happens to have value 0 and when
the last receive frame was an Association Request frame, the
sta->last_subtype == reassoc check was true and non-zero
WLAN_FC_STYPE_REASSOC_REQ was interpreted as true. However, this was
broken for Reassociation Request frame. reassoc == 1 in that case could
have matched received Association Response frame (subtype == 1), but
those are not received in AP mode and as such, this did not break other
behavior apart from not being able to drop duplicated Reassociation
Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds helper functions for deriving PMK and PMKID from ERP exchange
in FILS shared key authentication as defined in IEEE Std 802.11ai-2016,
12.12.2.5.2 (PMKSA key derivation with FILS authentication). These
functions is used to fix PMK and PMKID derivation which were previously
using the rMSK directly as PMK instead of following the FILS protocol to
derive PMK with HMAC from nonces and rMSK.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Beacon frames are not supported in IEEE 802.11ad network (DMG-beacons
used instead). To allow hostapd to manage IEEE 802.11ad AP with
device_ap_sme disabled, skip nl80211_register_beacons() for IEEE
802.11ad AP.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
These elements can be used for pre-standard publication testing of HE
before P802.11ax draft assigns the element ID extension. The payload of
these vendor specific elements is defined by the latest P802.11ax draft.
Please note that the draft is still work in progress and the element
payload is subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows kernel to force disconnection if something kills the
wpa_supplicant process in a manner that does not allow proper cleanup to
be performed. The association is not supposed to be allowed to continue
after process has ended since there are number of operations that
wpa_supplicant may need to do during the association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a call to the notify_beacon_loss() callback functions when
beacon loss is detected. In addition, a new CTRL-EVENT-BEACON-LOSS event
is made available through the wpa_supplicant control interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds processing of beacon loss events and generation of an internal
EVENT_BEACON_LOSS event based on them for wpa_supplicant processing. In
addition, number of consecutively lost (not acknowledged) packets is now
reported and TXE events are noted in the debug log.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the action TX status callback contents more thoroughly and report
the BEACON-REQ-TX-STATUS event only if the Measurement Type indicates
beacon report.
Signed-off-by: Jouni Malinen <j@w1.fi>
Authentication and Deauthentication frames are not used in DMG/IEEE
802.11ad networks. For DMG/IEEE 802.11ad the following was implemented:
Upon receiving association request, allocate the sta object and
initialize it as if authentication took place. Upon receiving
disassociation, deallocate the sta object.
ap_sta_disassociate/ap_sta_deauthenticate/ap_sta_disconnect all use
disassociation instead of deauthentication. In driver_nl80211,
i802_sta_deauth() is routed to i802_sta_disassoc().
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Supported Rates element is not present in DMG/IEEE 802.11ad frames. Make
copy_supp_rates() immediately return with success if hardware mode is
IEEE 802.11ad.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
It was possible that nl80211_get_hw_feature_data() function would return
NULL when num_modes is not set to zero. This might result in a later crash
when accessing hw.modes. This may be reproduced with hwsim oom tests, for
example, dbus_connect_oom.
Fix that by zeroing num_modes if NULL is returned.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This fixes the netlink attribute identifier for the scan flags when
using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd control interface event "BEACON-RESP-RX <STA address>
<dialog token> <report mode> <beacon report>" is now used to report
received beacon reports as a reponse to the REQ_BEACON operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new BEACON-REQ-TX-STATUS control interface event is now used to
report whether a beacon request (from REQ_BEACON command) was delivered
successfully. This event has the following parameters: <STA address>
<dialog token> <ack=0/1>.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new control interface command "REQ_BEACON <STA addr>
[req_mode=<mode>] <beacon request>" can now be used to request hostapd
to transmit a measurement request to request a beacon report from an
associated STA. This command returns the assigned dialog token (1-255)
or FAIL on failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
The loop to add hash values was supposed to be limited to at most 10000
values, but the count variable was not being decremented in the loop.
Fix this by decrementing counting for each iteration. This fixes
ANQP-element format in the unlikely case of there being more than 10000
configuration realms.
Signed-off-by: Jouni Malinen <j@w1.fi>
This conversion will be done several times in the code, so add a helper
function that does this conversion.
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
Add a function to get operating class definition (including bandwidth,
channel numbers, etc.) from the operating class number and country.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add helper function that converts non-global operating classes to global
operating classes according to IEEE Std 802.11-2016, Annex E.
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
Add support for:
1. Setting scan dwell time
2. Parsing scan start TSF and beacon received TSF reported
by the driver
3. Setting driver capabilities for the above
These capabilities are needed for Beacon Report radio measurement.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add the following parameters to scan request:
1. Dwell time on each channel.
2. Whether the specified dwell time is mandatory.
In addition, add to scan results info the time that the scan actually
started, and to each scan result the time the beacon/probe was received,
both in terms of TSF of the BSS that the interface that requested the
scan is connected to (if available).
Add flags to indicate whether the driver supports dwell time
configuration and scan information reporting.
This scan configuration and information is required to support beacon
report radio measurement.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The address of msg.device_name array is obviously always true, and some
compilers even warn about it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The actual BSS configuration parameter can be updated with the SET
control interface command, so there is no need to maintain a separate
per-BSS parameter and a separate control interface handling for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the hostapd ft_over_ds parameter was used to only advertise
whether FT-over-DS is enabled in MDE and leave it to the stations to
follow that advertisement. This commit extends this to explicitly reject
(silently drop) FT Action frames if a station does not follow the
advertised capabilities.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible to hit the previously used maximum of 100 active session
in some hwsim test case sequences like this one: eap_proto_pwd_errors
eap_proto_ikev2_errors eap_proto_sim_errors. This happened due to the
large number of RADIUS authentication iterations in short period of
time, i.e., within the 10 second timeout for expiring completed
sessions.
Increase RADIUS_MAX_SESSION from 100 to 1000 and also reduce the timeout
on expiring completed sessions from 10 to 5 seconds.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, this was noted in error log, but the invalid value was
stored in the configuration without rejecting it.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible to try to do driver operations before the driver
interface had been initialized when processing a SIGHUP signal. This
would result in NULL pointer dereference. Fix this by skipping the steps
when SIGHUP is issued before the interface is enabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function is already checking the fname argument against NULL, so
use that check on its own instead of duplicating the check in the only
caller.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a new wpa_supplicant network profile parameter
mka_priority=0..255 to set the priority of the MKA Actor.
Signed-off-by: Badrish Adiga H R <badrish.adigahr@gmail.com>
wpa_cipher_to_alg() returns enumerated values from enum wpa_alg and all
uses of the return value treat it as enum wpa_alg (by either assigning
it to a variable of type enum wpa_alg or passing to a function that
expects enum wpa_alg).
This commit updates the return value to match the expected usage
(enum wpa_alg) rather than int. This ensures the return value is
of the proper type and eliminates the following compiler warnings:
ARM RVCT (2.2):
'Warning: #188-D: enumerated type mixed with another type'
Signed-off-by: Joel Cunningham <joel.cunningham@me.com>
Number of deployed use cases assume the default OpenSSL behavior of auto
chaining the local certificate is in use. BoringSSL removed this
functionality by default, so we need to restore it here to avoid
breaking existing use cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This simplifies the implementation since the SSL_clear_options() and
SSL_CTX_clear_options() are available in all supported versions of
OpenSSL. These were previously needed with older (now obsolete) versions
of OpenSSL, but the ifdefs were missed when removing the more explicit
version macro based backwards compatibility sections.
In practice, this reverts commit
d53d2596e4.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The full SD Response frame is not going to be followed by another Action
frame from the peer, so remove the 200 ms wait time from the offchannel
TX command in that case. This avoids leaving a 200 ms lock on the radio
to remain on the channel unnecessarily.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is apparently possible for the NL80211_CMD_UNEXPECTED_4ADDR_FRAME
event to be delivered to hostapd before the NL80211_CMD_FRAME_TX_STATUS
event for (Re)Association Response frame. This resulted in the 4-address
WDS mode not getting enabled for a STA. This could occur in particular
when operating under heavy load and the STA is reconnecting to the same
AP in a sequence where Deauthentication frame is followed immediately by
Authentication frame and the driver event processing gets delayed due to
removal of the previous netdev taking time in the middle of this
sequence.
Fix this by recording a pending item for 4-address WDS enabling if the
NL80211_CMD_UNEXPECTED_4ADDR_FRAME event would have been dropped due to
incompleted association and then process this pending item if the TX
status for the (Re)Association Response frame is received and it shows
that the frame was acknowledged.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This registers a new callback to indicate change in SIM state. This
helps to do some clean up (more specifically pmksa_flush) based on the
state change of the SIM. Without this, the reconnection using the cached
PMKSA could happen though the SIM is changed.
Currently eap_proxy_sim_state corresponds to only SIM_STATE_ERROR. This
can be further extended.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The eapol_cb structure was made const and that change resulted in a
compilation warning/error if CONFIG_EAP_PROXY=<name> is enabled in the
wpa_supplicant build configuration. Fix this by updating the function
prototype to match the change.
Note: This results in a change needed to external eap_proxy_*.c
implementations to match the change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit c93b7e1888 ('RSN: Check result of
EAPOL-Key frame send request') forgot to update two PeerKey users of
EAPOL-Key TX functions. That resulted in STK handshake failing since
message 2/4 and 4/4 TX calls were assumed to have failed when the return
value was changed from 0 to a positive value for success case. This
resulted in not updating nonce information properly and hitting
following error when processing STK 4-way handshake message 3/4:
RSN: INonce from message 1 of STK 4-Way Handshake differs from 3 of STK
4-Way Handshake - drop packet (src=<addr>)
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 6d014ffc6e ('Make struct
wpa_eapol_key easier to use with variable length MIC') forgot to update
number of EAPOL-Key processing steps for SMK and STK exchanges and broke
PeerKey. Fix this by updating the Key Data field pointers to match the
new style with variable length Key MIC field.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter fils_realm=<realm> can now be
used to configure one or more FILS realms to advertise for ERP domains
when using FILS. This replaces the use of erp_domain=<domain> parameter
for the FILS use case.
Signed-off-by: Jouni Malinen <j@w1.fi>
P802.11ai/D7.0 changed from CRC32 to SHA256 as the hash algorithm for
the FILS realm name. Update the implementation to match that change.
Signed-off-by: Jouni Malinen <j@w1.fi>
This updates definitions for Status Codes, Reason Codes,
Information Element IDs, Action frame categories, Public Action
codes, Protected Dual of Public Action codes, Advertisement
Protocol ID, and ANQP info IDs based on IEEE Std 802.11-2016.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes both the Probe Response and Beacon frame IEs available to
upper layers if scan results include both IE sets. When the BSS command
mask includes WPA_BSS_MASK_BEACON_IE, a new beacon_ie=<hexdump> entry
will be included in output if the BSS entry has two separate sets of IEs
(ie=<hexdump> showing the Probe Response frame contents and
beacon_ie=<hexdump> the Beacon rame contents).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the secondary channel was not found at all, no debug print was shown
to indicate that the channel was rejected due to that problem. Print a
clearer message indicating which channel was behind the reason to reject
channel configuration as unsuitable for AP mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant control interface commands PMKSA_GET and
PMKSA_ADD that can be used to store PMKSA cache entries in an external
persistent storage when terminating a wpa_supplicant process and then
restore those entries when starting a new process. The previously added
PMKSA-CACHE-ADDED/REMOVED events can be used to help in synchronizing
the external storage with the memory-only volatile storage within
wpa_supplicant.
"PMKSA_GET <network_id>" fetches all stored PMKSA cache entries bound to
a specific network profile. The network_id of the current profile is
available with the STATUS command (id=<network_id). In addition, the
network_id is included in the PMKSA-CACHE-ADDED/REMOVED events. The
output of the PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration in seconds>
<akmp> <opportunistic>
For example:
02:00:00:00:03:00 113b8b5dc8eda16594e8274df4caa3d4 355e98681d09e0b69d3a342f96998aa765d10c4459ac592459b5efc6b563eff6 30240 43200 1 0
02:00:00:00:04:00 bbdac8607aaaac28e16aacc9152ffe23 e3dd6adc390e685985e5f40e6fe72df846a0acadc59ba15c208d9cb41732a663 30240 43200 1 0
The PMKSA_GET command uses the following format:
<network_id> <BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration
in seconds> <akmp> <opportunistic>
(i.e., "PMKSA_ADD <network_id> " prefix followed by a line of PMKSA_GET
output data; however, the reauth_time and expiration values need to be
updated by decrementing them by number of seconds between the PMKSA_GET
and PMKSA_ADD commands)
For example:
PMKSA_ADD 0 02:00:00:00:03:00 113b8b5dc8eda16594e8274df4caa3d4 355e98681d09e0b69d3a342f96998aa765d10c4459ac592459b5efc6b563eff6 30140 43100 1 0
PMKSA_ADD 0 02:00:00:00:04:00 bbdac8607aaaac28e16aacc9152ffe23 e3dd6adc390e685985e5f40e6fe72df846a0acadc59ba15c208d9cb41732a663 30140 43100 1 0
This functionality is disabled be default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option. It should be
noted that this allows any process that has access to the wpa_supplicant
control interface to use PMKSA_ADD command to fetch keying material
(PMK), so this is for environments in which the control interface access
is restricted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These allow external program to monitor PMKSA cache updates in
preparation to enable external persistent storage of PMKSA cache.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd didn't send "TERMINATING" event when stopped by
SIGTERM. Android handles this event to stop monitor thread.
This commit adds "TERMINATING" event same as with wpa_supplicant.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
This allows the vendor scan to be optimized when a response is needed
only from a single, known BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit documents the QCA vendor commands 61-73 and the
corresponding definitions of the attributes. This set of commands were
previously reserved for QCA without documentation here.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These thresholds values indicate how many Beacon frames can be missed
before before disconnecting from the AP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit c79238b6a4 ('Define a QCA vendor
command to configure SAR Power limits') had a mismatch between the enum
qca_vendor_attr_sar_limits_selections documentations and actual values.
The BDF SAR profiles are 0-based, so rename the enum values and reorder
the values keep the actual values more convenient. While this changes
values over the interface, this is justifiable since the new command was
introduced only recently and it had not been released in any driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is to handle the case when peer changes device name and same needs
to be updated to upper layers by P2P-DEVICE-FOUND event. It is similar
to the case when a peer changes wfd_subelems and P2P-DEVICE-FOUND event
goes to upper layers.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
When a peer device stops sending wfd_subelems, wpa_supplicant should
remove dev->info.wfd_subelems from peer's properties. Previously,
wpa_supplicant left the previously learned dev->info.wfd_subelems in
place whenever the new message did not include wfd_subelems.
In addition to fixing the clearing of the old wfd_subelems, this
resolves another issue. As "wfd_changed" variable becomes true even when
peer stops sending wfd_subelems and dev->info.wfd_subelems has an old
value, a new P2P-DEVICE-FOUND event notification was sent again and
again to upper layers whenever a new discovery response was received
from the peer that previously advertised WFD subelements.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Previously, this flag was cleared only in case of failed GO Negotiation.
That could leave the flag set for a peer and if a new group formation
was performed with the same peer before the entry expired, there was
increased risk of getting stuck in a state where neither peer replied to
a GO Negotiation Request frame if a GO Negotiation Response frame with
Status 1 was dropped.
The error sequence could happen in the go_neg_with_bss_connected test
case when timing was suitable to make the second GO negotiation drop a
pending TX Action frame if the GO Negotiation Response with Status 1 was
scheduled for transmission during a P2P scan and P2P_CONNECT was issued
before that scan got aborted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is a regulatory requirement for Specific Absorption Rate (SAR)
whereby the device transmit power is reduced when it is determined that
the device is in close proximity to the body. Implement a vendor command
interface to allow a userspace entity to dynamically control the SAR
power limits.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, os_sleep() was used to block the hostapd (or wpa_supplicant
AP/P2P GO mode) processing between sending out EAP-Failure and
disconnecting the STA. This is not ideal for couple of reasons: it
blocks all other parallel operations in the process and it leaves a
window during which the station might deauthenticate and the AP would
have no option for reacting to that before forcing out its own
Deauthentication frame which could go out after the STA has already
started new connection attempt.
Improve this design by scheduling an eloop timeout of 10 ms instead of
the os_sleep() call and perform the delayed operations from the eloop
callback function. This eloop timeout is cancelled if the STA
disconnects or initiates a new connection attempt before the 10 ms time
is reached. This gets rid of the confusing extra Deauthentication frame
in cases where the STA reacts to EAP-Failure by an immediate
deauthentication.
Signed-off-by: Jouni Malinen <j@w1.fi>
On a connect nl80211 event, wpa_supplicant uses
wpa_driver_nl80211_get_ssid() to fetch the current associated SSID to
compare to existing configurations. However,
wpa_driver_nl80211_get_ssid() uses drv->ssid, which is a cached value.
It is set when we explicitly initial a connect request using
wpa_supplicant. If the association was initiated outside of
wpa_supplicant, we need another way to populate drv->ssid. This commit
sets drv->ssid based on cfg80211 BSS information on connect/associate
nl80211 events.
Signed-off-by: Ningyuan Wang <nywang@google.com>
Commit adcd7c4b0b ('nl80211: Support
vendor scan together with normal scan') made the drv->scan_state updates
for NL80211_CMD_NEW_SCAN_RESULTS and NL80211_CMD_SCAN_ABORTED
conditional on drv->last_scan_cmd being NL80211_CMD_TRIGGER_SCAN. This
missed the part about the possibility of last_scan_cmd == 0 and an
externally started cfg80211 scan is ending. This could leave
drv->scan_state into SCAN_STARTED state even after the scan was
completed. Consequently, hwsim test cases could get stuck in reset()
handler waiting for scan to terminate.
Fix this by updating drv->scan_state also in drv->last_scan_cmd == 0
case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for nl80211 NL80211_CMD_SET_MULTICAST_TO_UNICAST
command.
By setting the new hostapd configuration option multicast_to_unicast=1,
hostapd configures this AP to perform multicast to unicast conversion.
When enabled, all multicast packets with ethertype ARP, IPv4, or IPv6
(possibly within an 802.1Q header) will be sent out to each station once
with the destination (multicast) MAC address replaced by the station's
MAC address. Note that this may break certain expectations of the
receiver, e.g., the ability to drop unicast IP packets encapsulated in
multicast L2 frames, or the ability to not send destination unreachable
messages in such cases.
This also does not implement Directed Multicast Service (DMS).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
We should unconditionally remove inactivity timers for wired network
cases. This commit checks for this after a new station association:
hapd->iface->drv_flags & WPA_DRIVER_FLAGS_WIRED
and then cancels the timeout and does not register a new one.
It prints out a debug message like this:
1476740180.276286: IEEE 802.1X: 00:02:00:00:00:07 CTRL_DIR entering
state FORCE_BOTH
1476740180.276295: hostapd_new_assoc_sta: canceled wired ap_handle_timer
timeout for 00:02:00:00:00:07
This was tested on a debian jessie amd64 system with a configured 120
second inactivity timer and the session did not timeout.
Signed-off-by: Sam Tannous <stannous@cumulusnetworks.com>
Do not use the generic bss_info_handler() design to fetch all scan
results into temporary memory buffer. Instead, use a separate BSS info
handler that fetches the requested information without fully parsing the
BSS entries and without allocating any memory for collecting all the
results.
This is also simplifying bss_info_handler() and nl80211_parse_bss_info()
design by getting rid of the special case that was used only for
nl80211_get_assoc_freq() and not normal scan result fetching.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of fetching all scan results to a temporary buffer, debug print
scan result dump directly from the message handler function one BSS at a
time.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a single scan result to be parsed at a time. This is a step
towards optimizing scan result fetching without having to allocate
memory for all entries at the same time.
Signed-off-by: Jouni Malinen <j@w1.fi>
The way the removal of duplicated (one per frequency) BSS entries in the
cfg80211 scan results were removed in driver_nl80211_scan.c
bss_info_handler() depended on having the full scan results available to
allow iteration through the other entries. This is problematic for the
goal of being able to optimize memory allocations for scan result
fetching in a manner that would not build the full result buffer in
memory.
Move this duplicate removal into bss.c since it has sufficient
information available for doing the same determination of which one of
two BSS entries is more current.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_priv did not yet support Beacon frame IEs (res->beacon_ie_len) which
resulted in invalid scan data being accepted in driver_privsep.c. Add
support for res->beacon_ie_len and also fix the validation step to take
this new variable length field into account.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a single scan result to be checked at a time. This is a step
towards optimizing scan result fetching without having to allocate
memory for all entries at the same time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This untangles the NL80211_CMD_GET_SURVEY handler loop from
NL80211_CMD_GET_SCAN processing so that the per-channel noise
information can be fetched with a common function to a local data
structure that can then be easily used to update individual scan results
(a single BSS) instead of having to go through a full set of scan
results. This is a step towards optimizing scan result fetching without
having to allocate memory for all entries at the same time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Data connection was lost if a station reassociated without the STA entry
being cleaned up on the AP side. Fix this by moving reconfiguration of
the STA WDS parameters in association response callback to happen only
after the STA flags have been updated to associated stated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are used only within driver_wired_common.c now at the end of the
refactoring changes, so there is no need to make these helper functions
available outside driver_wired_common.c.
Signed-off-by: Jouni Malinen <j@w1.fi>
This uses libnl3 to communicate with the macsec module available on
Linux. A recent enough version of libnl is needed for the macsec.h file
(which is not yet available in a formal libnl release at the time of
this commit).
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
