The new hostapd and wpa_supplicant configuration parameters dpp_name and
dpp_mud_url can now be used to set a specific name and MUD URL for the
Enrollee to use in the Configuration Request. dpp_name replaces the
previously hardcoded "Test" string (which is still the default if an
explicit configuration entry is not included). dpp_mud_url can
optionally be used to add a MUD URL to describe the Enrollee device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use the same rules for dropping driver notifications for Data frames
from unassociated stations as were added for Management frame reception.
This results in more consistent behavior in sending out Deauthentication
frames with Reason Code 6/7.
This case was already checking for unexpected multicast addresses, so
there was no issue for the PMF protections for unexpected disconnection.
Anyway, better avoid unnecessary Deauthentication frames consistently.
Signed-off-by: Jouni Malinen <j@w1.fi>
A new argument to the DPP_AUTH_INIT command (conn_status=1) can now be
used to set Configurator to request a station Enrollee to report
connection result after a successfully completed provisioning step. If
the peer supports this, the DPP-CONF-SENT event indicates this with a
new argument (wait_conn_status=1) and the Configurator remains waiting
for the connection result for up to 16 seconds.
Once the Enrollee reports the result, a new DPP-CONN-STATUS-RESULT event
is generated with arguments result, ssid, and channel_list indicating
what the Enrollee reported. result=0 means success while non-zero codes
are for various error cases as specified in the DPP tech spec. If no
report is received from the Enrollee, the event with "timeout" argument
is generated locally.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is more consistent with the use of CONFIG_DPP2 since the
Configuration Result message is sent only when using version 2 or newer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If only one of the allocations fails, the successful allocation needs to
be freed on the error path.
Fixes: 22f90b32f1 ("DPP2: Configuration Result message generation and processing")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous support in the 60 GHz band was for channels 1-4.
Add support for channels 5 and 6.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
IEEE Std 802.11F-2003 was withdrawn in 2006 and as such it has not been
maintained nor is there any expectation of the withdrawn trial-use
recommended practice to be maintained in the future. Furthermore,
implementation of IAPP in hostapd was not complete, i.e., only parts of
the recommended practice were included. The main item of some real use
long time ago was the Layer 2 Update frame to update bridges when a STA
roams within an ESS, but that functionality has, in practice, been moved
to kernel drivers to provide better integration with the networking
stack.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not process any received Management frames with unexpected/invalid SA
so that we do not add any state for unexpected STA addresses or end up
sending out frames to unexpected destination. This prevents unexpected
sequences where an unprotected frame might end up causing the AP to send
out a response to another device and that other device processing the
unexpected response.
In particular, this prevents some potential denial of service cases
where the unexpected response frame from the AP might result in a
connected station dropping its association.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows us to send the OBSS PD settings to the kernel, such that the
driver can propagate them to the hardware/firmware.
Signed-off-by: John Crispin <john@phrozen.org>
uClibc-ng optionally disabled deprecated POSIX functions like usleep,
causing compilation failures. This switches to nanosleep while retaining
support for older libcs that do not support nanosleep.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Update the documentation of QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST
to make it a nested attribute to carry frequencies of type u32.
This is to be in sync with the nl80211 attribute
NL80211_ATTR_SCAN_FREQUENCIES.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Hardcode this to be defined and remove the separate build options for
PMF since this functionality is needed with large number of newer
protocol extensions and is also something that should be enabled in all
WPA2/WPA3 networks.
Signed-off-by: Jouni Malinen <j@w1.fi>
With DFS offloaded to the driver, hostapd state and CAC info was not
updated in DFS-CAC-START event, so STATUS output showed wrong info. Fix
this by updating the CAC related state when processing the driver event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to allow clean transition from one inner EAP
authentication method to another one if EAP method negotiation is needed
within Phase 2.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows EAP-TLS to be used within an EAP-TEAP tunnel when there is
an explicit request for machine credentials. The network profile
parameters are otherwise same as the Phase 1 parameters, but each one
uses a "machine_" prefix for the parameter name.
Signed-off-by: Jouni Malinen <j@w1.fi>
OCSP configuration is applicable to each instance of TLS-based
authentication and as such, the configuration might need to be different
for Phase 1 and Phase 2. Move ocsp into struct eap_peer_cert_config and
add a separate ocsp2 network profile parameter to set this for Phase 2.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow the previously hardcoded maximum numbers of EAP message rounds to
be configured in hostapd EAP server. This can be used, e.g., to increase
the default limits if very large X.509 certificates are used for EAP
authentication.
Signed-off-by: Jouni Malinen <j@w1.fi>
These parameters for certificate authentication are identical for the
Phase 1 (EAP-TLS alone) and Phase 2 (EAP-TLS inside a TLS tunnel).
Furthermore, yet another copy would be needed to support separate
machine credential in Phase 2. Clean this up by moving the shared
parameters into a separate data struct that can then be used for each
need without having to define separate struct members for each use.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set the max value of optional bytes inside the data structure. This
requires us to calculate the actually used size when copying the
HE capabilities and generating the IE.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
OSEN element was getting added both through the Authenticator IEs
(before some non-vendor elements) and separately at the end of the
frames with other vendor elements. Fix this by removing the separate
addition of the OSEN element and by moving the Authenticator IE addition
for OSEN to match the design used with WPA so that the vendor element
gets added in the proper place in the sequence of IEs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Even though the station is not supposed to include Hotspot 2.0
Indication element in the Association Request frame when connecting to
the open OSU BSS, some station devices seem to do so. With the strict
PMF-required-with-Hotspot-2.0-R2 interpretation, such connection
attempts were rejected. Relax this to only perform the PMF check if the
local AP configuration has PMF enabled, i.e., for the production BSS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Merge the separate debug print with the text name of the EAP code into
the same debug line with the numerical value to clean up debug log.
Signed-off-by: Jouni Malinen <j@w1.fi>
Need to leave EAP-TEAP methodState == MAY_CONT when marking decision =
FAIL based on inner EAP method failure since this message will be
followed by protected failure indication.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new eap_teap_id=5 hostapd configuration parameter value can be used
to configure EAP-TEAP server to request and require user and machine
credentials within the tunnel. This can be done either with Basic
Password Authentication or with inner EAP authentication methods.
Signed-off-by: Jouni Malinen <j@w1.fi>
Track PMK-R0/PMK-R0-Name from the initial mobility domain association
and derive PMK-R1/PTK when the station uses FT protocol. This allows
frames from additional roaming cases to be decrypted.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows a separate machine credential to be used for authentication
if the server requests Identity-Type = 2 (machine).
Signed-off-by: Jouni Malinen <j@w1.fi>
This is an initial step in adding support for configuring separate user
and machine credentials. The new wpa_supplicant network profile
parameters machine_identity and machine_password are similar to the
existing identity and password, but explicitly assigned for the purpose
of machine authentication.
This commit alone does not change actual EAP peer method behavior as
separate commits are needed to determine when there is an explicit
request for machine authentication. Furthermore, this is only addressing
the username/password credential type, i.e., additional changes
following this design approach will be needed for certificate
credentials.
Signed-off-by: Jouni Malinen <j@w1.fi>
Be more consistent on checking all parameter allocation and copying
steps within radius_server_init() and abort startup if anything fails
instead of trying to continue with other parts of the configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use struct eap_config as-is within RADIUS server to avoid having to
duplicate all the configuration variables at each interface. This
continues cleanup on struct eap_config duplication in hostapd.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Crypto-Binding TLV is included without Intermediate-Result TLV in
this sequence since the server is skipping all inner authentication
methods and is only sending out Result TLV with the Crypto-Binding TLV.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter eap_teap_id can be used to
configure the expected behavior for used identity type.
Signed-off-by: Jouni Malinen <j@w1.fi>
Parse the received Identity-Type TLV and report the used Identity-Type
in response if the request included this TLV. For now, only the
Identity-Type 1 (User) is supported.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow 100 rounds of EAP messages if there is data being transmitted.
Keep the old 50 round limit for cases where only short EAP messages are
sent (i.e., the likely case of getting stuck in ACK loop).
This allows larger EAP data (e.g., large certificates) to be exchanged
without breaking the workaround for ACK loop interop issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use struct eap_config as-is within struct eap_sm and EAPOL authenticator
to avoid having to duplicate all the configuration variables at each
interface. Split the couple of session specific variables into a
separate struct to allow a single const struct eap_config to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The implementation was previously hardcoded to use only the non-expanded
IETF EAP methods in Phase 2. Extend that to allow vendor EAP methods
with expanded header to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was already allowed with EAP-PEAP, but EAP-TEAP was hardcoded to
use only the non-expanded EAP types. Extend that to allow vendor EAP
types to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The implementation was previously hardcoded to use only the non-expanded
IETF EAP methods in Phase 2. Extend that to allow vendor EAP methods
with expanded header to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was already allowed with EAP-PEAP, but EAP-FAST was hardcoded to
use only the non-expanded EAP types. Extend that to allow vendor EAP
types to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The implementation was previously hardcoded to allow only the Microsoft
SoH expanded EAP method in Phase 2 in addition to non-expanded EAP
methods. Extend that to allow any vendor EAP method with an expanded
header to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The implementation was previously hardcoded to use only the non-expanded
IETF EAP methods in Phase 2. Extend that to allow vendor EAP methods
with expanded header to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was already allowed with EAP-PEAP, but EAP-TTLS was hardcoded to
use only the non-expanded EAP types. Extend that to allow vendor EAP
types to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
This cleans up coding style of the EAP implementation by avoiding
typedef of an enum hiding the type of the variables.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new eap_teap_separate_result=1 hostapd configuration parameter can
be used to test TEAP exchange where the Intermediate-Result TLV and
Crypto-Binding TLV are send in one message exchange while the Result TLV
exchange in done after that in a separate message exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the Crypto-Binding TLV for the last EAP method has been validated
successfully in a previous message exchange with Intermediate-Result TLV
and no new EAP method has been started, Result TLV can be accepted
without an additional Crypto-Binding TLV. This allows the server to go
through additional message exchanges after inner EAP method, if needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is not sufficient for the peer to include only the Result TLV if the
server included both the Intermediate-Result TLV and Result TLV.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, only the Result TLV was added when writing Crypto-Binding
TLV response. This is not sufficient, since RFC 7170 require
Intermediate-Result TLV response to be included from the peer if the
server included Intermediate-Result TLV.
Signed-off-by: Jouni Malinen <j@w1.fi>
This version of TLS PRF is needed when using TEAP with TLS ciphersuites
that are defined to use SHA384 instead of SHA256.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previously used single TOD policy was split into two policies:
TOD-STRICT and TOD-TOFU. Report these separately in the
CTRL-EVENT-EAP-PEER-CERT events (tod=1 for TOD-STRICT and tod=2 for
TOD-TOFU).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update Connection Params is intended for drivers that implement
internal SME and expect these updated connection params from
wpa_supplicant. Do not send this request for the drivers using
SME from wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If FT over-the-DS case is enforced through the "FT_DS <BSSID>" control
interface command, the PMF capability check during BSS selection is not
used and that could have allowed PMF to be disabled in the over-the-DS
case even if the local network profile mandated use of PMF. Check
against this explicitly to avoid unexpected cases if the APs within the
same mobility domain are not configured consistently.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Commit e820cf952f ("MFP: Add MFPR flag into station RSN IE if 802.11w
is mandatory") added indication of MFPR flag in non-FT cases, but forgot
to do so for the FT protocol cases where a different function is used to
build the RSNE. Do the same change now for that FT specific case to get
consistent behavior on indicating PMF configuration state with MFPR.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is not used only with FT, so make the comments less confusing and
include the function in all builds to make it available for
non-FT/non-FILS builds.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
HE (802.11ax) is also supported on 2.4 GHz. And the 2.4 GHz band isn't
supposed to use VHT operations. Some codepaths in wpa_supplicant will
therefore not initialize the freq->bandwidth or the freq->center_freq1/2
members. As a result, the nl80211_put_freq_params() will directly return
an error (-1) or the kernel will return an error due to the invalid
channel definition.
Instead, the channel definitions should be created based on the actual
HT/VHT/none information on 2.4 GHz.
Fixes: ad9a1bfe78 ("nl80211: Share VHT channel configuration for HE")
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Add vendor command QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT
and attribute qca_wlan_vendor_attr_avoid_frequency_ext to send structured
avoid frequency data.
This new command is alternative to existing command
QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY since existing command is
using stream of bytes instead of structured data using vendor attributes.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
As a part of P802.11ax amendment, 6 GHz band operation is added.
Since the 6 GHz channel numbers are overlapping with existing 2.4 GHz
and 5 GHz channel numbers, use frequency to identify unique channel
operation instead of channel number. Channel frequency is unique across
bands.
In the existing QCA vendor interface, wherever missing, add frequency
attributes to identify unique channel operation. In addition, add
comments to document some of the previously missed attributes/values.
Note: If both channel and frequency attributes are present in vendor
command/event and
(a) If both the driver and user-space application supports 6 GHz band
then channel related attributes are deprecated and use frequency
attributes.
(b) If either driver or user-space application or both doesn't
support 6 GHz band then use channel attributes.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Add QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL attribute in
enum qca_wlan_vendor_attr_sap_config to use with vendor command
QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG.
This new attribute is used to restart AP on given channel.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Add a QCA vendor sub command QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY
with attributes enum qca_wlan_vendor_attr_acs_config and
enum qca_acs_dfs_mode to configure ACS policy.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
This enhances the existing vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM
with the following configurations:
1. Set/get/clear roam control
2. Set/get the channels on which the roaming has to be triggered.
3. Set/get the roam scan period.
4. Configure the triggers for roaming.
5. Configure the candidate selection criteria.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
qca_wlan_vendor_attr_roam_subcmd is an enum associated with the
attribute QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD. It represents different
sub command values and these are not the attributes. Hence, rename the
enum to qca_wlan_vendor_roaming_subcmd. Accordingly, the members of this
enum are also renamed to suite the usage.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update the version number for the build and also add the ChangeLog
entries for both hostapd and wpa_supplicant to describe main changes
between v2.7 and v2.8.
Signed-off-by: Jouni Malinen <j@w1.fi>
Need to update methodState/decision when completing transmission of
fragmented last Phase 2 message.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The KCK, PMK, and PMKID derivation fix broke SAE key derivation for all
FFC groups. Fix that by setting sae->tmp->order_len for FFC groups (it
was only set for ECC groups).
Fixes: ac734a342e ("SAE: Fix KCK, PMK, and PMKID derivation for groups 22, 23, 24")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It looks like EVP_PKEY_derive() may change the returned length of the
buffer from the initial length determination (NULL buffer) to the
fetching of the value. Handle this by updating the secret length based
on the second call instead of the first one. This fixes some cases where
ECDH result has been used with extra data (zeros in the end) with OWE or
FILS PFS.
Signed-off-by: Jouni Malinen <j@w1.fi>
This replaces the separately implemented ECDH operations with a single
helper function to avoid code duplication. In addition, this introduces
a workaround for strange OpenSSL behavior where the first
EVP_PKEY_derive(NULL) call to learn the size of the output shared secret
returns unexpectedly large buffer (72 octets when expected 32 octets for
group 19). It is not known what is causing this, but such behavior seems
to be showing up every now and then at least when running hwsim test
cases under UML and apparently mainly (only?) in the sigma_dut
controller cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2016 is not exactly clear on the encoding of the bit
string that is needed for KCK, PMK, and PMKID derivation, but it seems
to make most sense to encode the (commit-scalar + peer-commit-scalar)
mod r part as a bit string by zero padding it from left to the length of
the order (in full octets).
The previous implementation used the length of the prime (in full
octets). This would work for KCK/PMK, but this results in deriving all
zero PMKIDs for the groups where the size of the order is smaller than
the size of the prime. This is the case for groups 22, 23, and 24.
However, those groups have been marked as being unsuitable for use with
SAE, so this fix should not really have a practical impact anymore.
Anyway, better fix it and document this clearly in the implementation
taken into account the unclarity of the standard in this area.
Signed-off-by: Jouni Malinen <j@w1.fi>
The earlier change to add support for BN_bn2binpad() and
BN_bn2bin_padded() broke this function for cases where no padding is
used (padlen == 0). Those would have always failed after the changes and
the function would return -1. There are no such cases in the current
hostap.git, so this did not have any real issues, but anyway, better fix
this function to match its documentation.
Fixes: 1e237903f5 ("OpenSSL: Use BN_bn2binpad() or BN_bn2bin_padded() if available")
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit d896874f86 ("nl80211: Indicate 802.1X 4-way handshake offload
in connect") used the req_key_mgmt_offload flag to indicate to the
driver that it should offload the 802.1X handshake. However, this field
was existing and used for a different offload API. This causes
wpa_supplicant to send a connect request without the WANT_1X_HS flag and
the subsequent set-pmk is rejected causing the connection to fail. Fix
that by introducing a new flag req_handshake_offload so the offloads are
no longer entangled.
Fixes: d896874f86 ("nl80211: Indicate 802.1X 4-way handshake offload in connect")
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Tested-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
The new hostapd configuration option eap_sim_id can now be used to
disable use of pseudonym and/or fast reauthentication with EAP-SIM,
EAP-AKA, and EAP-AKA'.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the EAP-SIM/AKA server does not provide a new pseudonym and the
locally configured "pseudonym" in anonymous_identity is actually an
anonymous identitity instead of a real EAP-SIM/AKA pseudonym, do not
clear the anonymous_identity network profile parameter. This is needed
to avoid forgetting the anonymous identity when going through
EAP-SIM/AKA authentication and then reverting back to using IMSI-based
(e.g., encrypted) identity.
Fixes: 4df4133917 ("EAP-SIM/AKA: Add support for anonymous@realm")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The relevant flags were only added in Linux 4.6, so we shouldn't
complain because they're missing. Also, they're always missing if a
device is being removed (e.g., 'iw dev wlan0 del', or if the device is
in the process of resetting itself). So kill those 2 birds with 1 stone:
if we can't find the file, just silently skip it.
Also, we probably should *actually* propagate the error if we had a
write failure.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Add an SQLite table for defining per station MAC address version of
radius_auth_req_attr/radius_acct_req_attr information. Create the
necessary table and index where this doesn't exist. Select attributes
from the table keyed by station MAC address and request type (auth or
acct), parse and apply to a RADIUS message.
Add radius_req_attr_sqlite hostapd config option for SQLite database
file. Open/close RADIUS attribute database for a lifetime of a BSS and
invoke functions to add extra attributes during RADIUS auth and
accounting request generation.
Signed-off-by: Terry Burton <tez@terryburton.co.uk>
We will want to parse RADIUS attributes in config file format when
retrieving them from an SQLite database.
Signed-off-by: Terry Burton <tez@terryburton.co.uk>
Previously, check for local MI,MN in a peer's Peers List accepted only
the cases that include the last used MN from an MKPDU sent by the local
device. This was problematic since it was possible to synchronize MKPDU
transmission between two devices in a way that made them always miss the
last MKPDU from the other device before filling in the Peers List.
Relax this matching requirement of "acceptably recent MN" to mean both
the last used MN and the one used just before it (i.e., copied from
either of the last two MKPDUs sent by the local device) are accepted.
While this might help in some real world scenarios in making the
protocol converge more quickly, the main help from this is to fix
consistent hwsim test cases failures in macsec_psk_ns when using UML
with time travel option which happened to practically guarantee the
inconvenient timing of MKPDU transmission/reception that ended up with
the MKPDU processing to see MI,MN with MN being the last used MN minus
1.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Disable groups that use Brainpool curves for now since they leak more
timing information due to the prime not being close to a power of two.
This removes use of groups 28, 29, and 30 from SAE and EAP-pwd.
Signed-off-by: Jouni Malinen <j@w1.fi>
The AP mode fix for removing NL80211_ATTR_STA_WME from
NL80211_CMD_SET_STATION did not consider the TDLS case and that resulted
in incorrectly removing WMM parameters from TDLS STA entry updates. Fix
this by considering the WPA_STA_TDLS_PEER flag similarly to the other
update parameters.
Fixes: 6d14b98fc6 ("nl80211: Do not add WMM parameters when updating an existing STA entry")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a compiler specific extension and not compliant with the C
standard.
Fixes: 1c16b257a0 ("EAP-SIM: Add Session-Id derivation during fast-reauth")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a compiler specific extension and not compliant with the C
standard.
Fixes: 5eefa8115b ("EAP-AKA: Add Session-Id derivation during fast-reauth")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new "wpa" and "AKMSuiteSelector" entries in hostapd "STA <addr>"
control interface output can be used to determine the negotiated WPA/RSN
protocol and AKM suite of an associated station.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These SAE, OWE, DPP, and OSEN AKM suite selectors were covered in the
reverse conversion in rsn_key_mgmt_to_bitfield(), but were missing from
wpa_akm_to_suite(). Add them to make AKM suite selector reporting more
accurate in RADIUS Accounting messages (and future users of this
function).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use a shared function to determine the k parameter, i.e., the minimum
number of iterations of the PWE derivation loop, for SAE and EAP-pwd.
This makes it easier to fine-tune the parameter based on the negotiated
group, if desired.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make the EAP-pwd peer use same default set of allowed groups as the SAE
implementation in wpa_supplicant uses, i.e., the groups 19-21 using NIST
curves P-256, P-384, and P-521. Previously, all groups that were
supported by the crypto library were allowed. In practice, this change
disables use of the Brainpool curves (groups 28-30) with recent OpenSSL
versions.
The default set of groups can be overridden with a new phase1 network
profile parameter, eap_pwd_groups=<list of allowed ranges>. For example,
phase1="eap_pwd_groups=0-65535" would restore previous behavior of
allowing all implemented groups to be used while eap_pwd_groups=19,20
would enable only the groups using NIST curves P-256 and P-384 to be
used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add attributes QCA_WLAN_VENDOR_ATTR_CONFIG_ELNA_BYPASS under
the enum qca_wlan_vendor_attr_config to support set and get
the ELNA bypass.
Signed-off-by: Paul Zhang <paulz@codeaurora.org>
Add a new vendor attribute QCA_WLAN_VENDOR_ATTR_DISCONNECT_IES
to configure disconnect IEs to the driver. Driver shall fill
these IEs in disassoc/deauth frame.
These IEs are expected to be considered only for the next
immediate disconnection (disassoc/deauth frame) originated by
the DUT, irrespective of the entity (user space/driver/firmware)
triggering the disconnection.
The host drivers are not expected to use the IEs set through
this interface for further disconnections after the first immediate
disconnection initiated post the configuration.
If the IEs are also updated through cfg80211 interface (after the
enhancement to cfg80211_disconnect), host driver is expected to
take the union of IEs from both of these interfaces and send in
further disassoc/deauth frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor sub command QCA_NL80211_VENDOR_SUBCMD_OEM_DATA
with attributes qca_wlan_vendor_attr_oem_data_params to support
OEM data. It is used to send OEM data binary blobs from
application/service to firmware. The attributes defined in enum
qca_wlan_vendor_attr_oem_data_params are used to deliver the
parameters.
Signed-off-by: Paul Zhang <paulz@codeaurora.org>
The new certificate chain debug dumps used functions that are not
available with LibreSSL or BoringSSL.
Fixes: 857edf4bf4 ("OpenSSL: More debug prints of configured ciphers and certificates")
Signed-off-by: Jouni Malinen <j@w1.fi>
The OPENSSL_VERSION_NUMBER ifdef block left out the local variable that
is needed with all versions. In addition, SSL_set_security_level() is
not available with LibreSSL or BoringSSL.
Fixes: 3ec65a8e38 ("OpenSSL: Allow anon-DH cipher suites to be added for TEAP")
Signed-off-by: Jouni Malinen <j@w1.fi>
The tls_connection_get_cipher_suite() implementation used
SSL_CIPHER_get_protocol_id which was added in OpenSSL 1.1.1. Need to use
compatibility code with older versions.
Fixes: 94714ec341 ("OpenSSL: Add tls_connection_get_cipher_suite()")
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds an encrypted version of a one octet application data payload
to the end of the handshake when TLS v1.3 is used to indicate explicit
termination of the handshake (either after Finished message or after the
optional NewSessionTicket message). The current
draft-ietf-emu-eap-tls13-05 defines this to be a zero length payload,
but since that is not allowed by OpenSSL, use a one octet payload
instead for now with hopes of getting the draft specification updated
instead of having to modify OpenSSL for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
EAP-TLS with TLS 1.3 uses an empty application data record from the
server to indicate end of the exchange, so EAP-TLS peer will need to
check for this special case and finish the exchange with an empty
EAP-TLS (ACK) so that the server can send out EAP-Success.
Signed-off-by: Jouni Malinen <j@w1.fi>
This will hopefully not be needed for EAP-TLS use cases since there
should not really be a middlebox that looks at the TLS layer details in
case of EAP authentication.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd EAP server can now be configured with two separate server
certificates/keys to enable parallel operations using both RSA and ECC
public keys. The server will pick which one to use based on the client
preferences for the cipher suite (in the TLS ClientHello message). It
should be noted that number of deployed EAP peer implementations do not
filter out the cipher suite list based on their local configuration and
as such, configuration of alternative types of certificates on the
server may result in interoperability issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds support for a new EAP method: EAP-TEAP (Tunnel Extensible
Authentication Protocol). This should be considered experimental since
RFC 7170 has number of conflicting statements and missing details to
allow unambiguous interpretation. As such, there may be interoperability
issues with other implementations and this version should not be
deployed for production purposes until those unclear areas are resolved.
This does not yet support use of NewSessionTicket message to deliver a
new PAC (either in the server or peer implementation). In other words,
only the in-tunnel distribution of PAC-Opaque is supported for now. Use
of the NewSessionTicket mechanism would require TLS library support to
allow arbitrary data to be specified as the contents of the message.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new TLS_CONN_* flag to provide a higher level mechanism for adding
(instead of fully replacing) allowed list of TLS ciphersuites for TEAP
provisioning purposes.
Signed-off-by: Jouni Malinen <j@w1.fi>
This implements "tls-unique" derivation per RFC 5929, Section 3. This
will be needed for channel binding, e.g., with EAP-TEAP.
Signed-off-by: Jouni Malinen <j@w1.fi>
The buf[] array is initialized to zeros, so it was already null
terminated since the read() call did not allow the last character of the
buffer to be overwritten. Since that was apparently not enough to make
some static analyzers understand the design, use explicit null
termination after a successful read() call.
Signed-off-by: Jouni Malinen <j@w1.fi>
This reduces differences in timing and memory access within the
hunting-and-pecking loop for ECC groups that have a prime that is not
close to a power of two (e.g., Brainpool curves).
Signed-off-by: Jouni Malinen <j@w1.fi>
This reduces differences in timing and memory access within the
hunting-and-pecking loop for ECC groups that have a prime that is not
close to a power of two (e.g., Brainpool curves).
Signed-off-by: Jouni Malinen <j@w1.fi>
'sizeof' was not used with os_memmove() for an integer array. This lead
to an issue with part of the preferred channel list not being used.
Fixes: 79329ae0aa ("P2P: Verify local driver preferred frequencies for P2P use cases")
Signed-off-by: Daichi Ueura <daichi.ueura@sony.com>
Mesh points can partially support HE features (when requiring no
controlling STA/AP) as long as hardware supports it. The kernel just
requires support for HE mesh and wpa_supplicant can forward the peer
capabilities to the kernel for further processing.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
The HE capabilities are no longer per PHY but per iftype on this
specific PHY. It is therefore no longer enough to just parse the AP
capabilities.
The he_capabilities are now duplicated to store all information for
IEEE80211_MODE_* which hostap cares about. The nl80211 driver fills in
this information when the iftype supports HE. The rest of the code still
only uses the IEEE80211_HE_AP portion but can be extended later to also
use other HE capabilities.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Declare the variable only once and reuse it instead of openning
unneeded scopes.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The the mask for PPE threshold present in the HE phy capability byte 6 is
0x80 and not 0x6. This incorrect mask breaks the length calculation and as
result the acceptance of the HE capabilities for STAs which either:
* don't have the PPE threshold present bit set AND the Codebook Size={7,5}
MU Feedback or the Triggered SU Beamforming feedback bit set
* do have the PPE threshold present set AND neither the Codebook Size={7,5}
MU Feedback nor the Triggered SU Beamforming feedback bit set
Fixes: 8f5fc369e2 ("HE: Fix HE Capabilities element variable length encoding")
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Some compilers have started to warn about this and the use of two loops
with ix 0..pa-1 and 0..pa loop a bit suspicious, so better make sure the
array is initialized with zeros before extracting the terms from it.
Signed-off-by: Jouni Malinen <j@w1.fi>
This does not need to be specific to X.509, so move the BOOLEAN DER
encoding validation into asn1_get_next() to make it apply for all cases
instead of having to have the caller handle this separately.
Signed-off-by: Jouni Malinen <j@w1.fi>
While BER encoding allows any nonzero value to be used for TRUE, DER is
explicitly allowing only the value 0xff. Enforce this constraint in
X.509 parsing to be more strict with what is acceptable.
Signed-off-by: Jouni Malinen <j@w1.fi>
Handling of the optional pathLenConstraint after cA was not done
properly. The position after cA needs to be compared to the end of the
SEQUENCE, not the end of the available buffer, to determine whether the
optional pathLenConstraint is present. In addition, when parsing
pathLenConstraint, the length of the remaining buffer was calculated
incorrectly by not subtracting the length of the header fields needed
for cA. This could result in reading couple of octets beyond the end of
the buffer before rejecting the ASN.1 data as invalid.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=15408
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a CTRL-EVENT-EAP-PEER-CERT even for depth=0 even if a depth >
0 certificate results in peer certificate validation error. Previously,
this case resulted in the upper layers not getting any information about
the used peer certificate. Now that information is available, e.g., to
allow server certificate -based overriding of the trust to be done.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The same len variable can be used for both needs within
ieee802_1x_get_keys() to avoid compiler warning about use of shadowed
variable.
Fixes: 0ee6885dae ("macsec: Store EAP-Key-Name as eapSessionId")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This implements the required functionality in hostapd to facilitate OWE
connection with the AP SME-in-driver cases. Stations can either send DH
IE or PMKID (in RSNE) (or both) in Association Request frame during the
OWE handshake. The drivers that use this offload mechanism do not
interpret this information and instead, pass the same to hostapd for
further processing. hostapd will either validate the PMKID obtained from
the STA or generate DH IE and further indicate the same to the driver.
The driver further sends this information in the Association Response
frame.
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
Signed-off-by: Liangwei Dong <liangwei@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This command/event interface can be used by SME based host drivers that
rely on user space (hostapd/wpa_supplicant) for DH IE
processing/generation. This interface facilitates the OWE connection
with host drivers by offloading DH IE processing to the user space
(hostapd/wpa_supplicant).
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
Signed-off-by: Liangwei Dong <liangwei@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to allow upper layer software to learn the hash of the
server certificate for allowing user to override trust root
configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add tod=1 to CTRL-EVENT-EAP-PEER-CERT events if the peer certificate
includes the TOD policy in the X.509v3 Certificate Policies extension.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it easier to add new information to the callbacks without
having to modify each callback function type in EAPOL and EAP code every
time.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
sscanf() can apparently read beyond the end of the buffer even if the
maximum length of the integer is specified in the format string. Replace
this parsing mechanism with helper functions that use sscanf() with NUL
terminated string to avoid this.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=15158
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
src/*/Makefile needs to allow additional CFLAGS values to be provided
from the calling Makefiles so that the clang command line arguments to
enable sanitizers consistently. In addition, it can be useful to be able
to provide CC, CFLAGS, and LDFLAGS from external setup while still
requesing LIBFUZZER=y build. Allow that by not overriding these
variables if they are already set.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The driver automatically starts beacon reporting if it pauses the beacon
reporting for any reason other than disconnection. In specific cases,
userspace may not want the beacon reporting to be automatically resumed
after a pause. Add interface support for userspace to specify driver not
to start beacon reporting automatically after a pause.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the EAP Session-ID is available, add it into Access-Accept
(EAP-Key-Name attribute). This is needed for MACsec.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is safer to maintain the old EAPOL version (2) in EAPOL frames that
are not related to MACsec and only update the version to 3 for the
MACsec specific cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the following vendor attributes under the enum
qca_wlan_vendor_attr_spectral_scan to support the configuration of
Spectral DMA debug.
1. QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_RING_DEBUG
Enable/disable debug of the Spectral DMA ring
2. QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_BUFFER_DEBUG
Enable/disable debug of the Spectral DMA buffers
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
SIM-based EAP authentication with IMSI encryption requires a special EAP
Identity response: anonymous@realm. Then the server sends AKA-Identity
request which is answered with the encrypted IMSI. Add logic that
indicates if the special anonymous identity is used. Otherwise, this
field is used for storing the pseudonym.
Test: Connect to Carrier Wi-Fi, verify correct behavior from captures
Test: Connect to non IMSI encrypted EAP-AKA AP, verify pseudonym usage
Signed-off-by: Hai Shalom <haishalom@google.com>
External auth status to the driver includes the PMKID derived as part of
SAE authentication, but this is not valid if PMKSA caching is disabled.
Drivers might not be expecting PMKID when it is not valid. Do not send
the PMKID to the driver in such cases.
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
A driver that uses internal AP SME may need to be able to use the
external_auth status operation in station mode, so do not skip this
solely based on drv->device_ap_sme; instead, use that condition only
when operating in AP mode.
Fix external_auth status in non SME case.
Signed-off-by: Ashok Kumar <aponnaia@codeaurora.org>
With radio work design, send Action frame request will be queued and
wait for p2p-scan to finish, so there is no need to delay send_action.
This change revisits the logic (added before the radio work framework)
in below commits:
3f9285f P2P: Delay send_action call if p2p_scan is in progress
f44ae20 P2P: Drop pending TX frame on new p2p_connect
9d562b7 P2P: Add p2p_unauthorize command
63a965c P2P: Fix after_scan_tx processing during ongoing operations
9a58e52 P2PS: Callback to create pending group after sending PD Response
3433721 P2P: Continue p2p_find after sending non-success Invitation Response
Signed-off-by: Hu Wang <huw@codeaurora.org>
In case the current channel has regulatory WMM limitations, take them
into account when filling the WMM element. Also check if the new WMM
element is different from the previous one and if so change the
parameter_set_count to imply stations to look into it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
ETSI EN 301 893 v2.1.1 (2017-05) standard defines a new channel access
mechanism that all devices (WLAN and LAA) need to comply with.
In previous versions the device was allowed by ETSI to implement
802.11 channel access mechanism based on a set of priority classes
which are taken from 802.11. According of the new standard there
might be some exceptions which require ETSI countries to follow
more restrictive rules. In such a case the AP's wmm IE need to
comply with ETSI limitation. To be able to do so the regulatory
domain passes the new limitation values if needed.
Implement this, by storing it and use it to calculate the new
WMM parameters.
This commit adds determination of regulator limitations to
NL80211_CMD_GET_WIPHY processing so that the information is available
for upper layer implementation to use later when constructing WMM
element.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Add support for injecting frames to a given mesh peer, bypassing the
mpath table lookup using PROBE_MESH_LINK command. This helps to send
data frames over unexercised direct mesh path, which is not selected as
next_hop node. This can be helpful in measuring link metrics.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
In the case of the ap_csa_disable test, I frequently see
failures due to the kernel *not* having switched, but the
CSA-STARTED event having been processed, and thus the
frequency having been updated already.
This is wrong at least for AP mode, the frequency we store
for this case internally in nl80211 should only be updated
when the channel switch completes, otherwise we end up in
a situation where the switch is aborted and the kernel is
thus on the old channel, but the internal information has
been updated and every subsequent mgmt-frame TX fails due
to being tagged with the wrong channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
GnuTLS backend already accepts CA cert blobs in both DER and PEM
formats. Implement similar trial-and-error handling in OpenSSL backend.
Signed-off-by: Santtu Lakkala <santtu.lakkala@jolla.com>
When a new station is added, let it have some supported rates
(they're empty without this change), using the basic rates
that it must support to connect.
This, together with the kernel-side changes for client-side,
lets us finish the complete auth/assoc handshake with higher
rates than the mandatory ones, without any further config.
However, the downside to this is that a broken station that
doesn't check the basic rates are supported before it tries
to connect will possibly not get any response to its auth
frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a config option to allow setting a custom Basic NSS/MCS set. As a
default we use single stream HE-MCS 0-7.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Set operating channel bandwidth and center frequencies using the same
attributes for VHT and HE.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Process HE information in (Re)Association Request frames and add HE
elements into (Re)Association Response frames when HE is enabled in the
BSS.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The HE Capibilities element has dynamic size due to the variable length
and optional fields at the end. Mask out the channel width capabilities
that are less than the configured. Only add the MCS/NSS sets for the
announced channel widths and also add the PPET elements.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The PPE Thresholds information in the end of the HE Capabilities element
is optional and of variable length. struct he_ppe_threshold was not
really used correctly for encoding this, so remove it and just reserve
enough space for the information.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This is used for both VHT and HE, so remove the misleading prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
These are used for both VHT and HE, so remove the misleading prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
These are used for both VHT and HE, so remove the misleading prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Bandwidth is used for both VHT and HE here.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
oper_chwidth is used for both VHT and HE here.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The bandwidth values are shared between VHT and HE mode so remove the
VHT specific prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
These bits might be set by the capabilities read from the kernel, so
mask them out if beamforming is not enabled in the local configuration.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This copying attempt was added incorrectly since that element is never
actually present in (Re)Association Request frames. It is only valid to
copy that element from the mesh peering frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
gcc 8.3.0 was apparently clever enough to optimize away the previously
used os_memset() to explicitly clear a stack buffer that contains keys
when that clearing happened just before returning from the function.
Since memset_s() is not exactly portable (or commonly available yet..),
use a less robust mechanism that is still pretty likely to prevent
current compilers from optimizing the explicit clearing of the memory
away.
Signed-off-by: Jouni Malinen <j@w1.fi>
Initialize auth_sock and acct_sock to -1 to avoid radius_server_deinit()
attempting to close fd=0 if anything fails in setting up the RADIUS
server.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Session-Id derivation for EAP-AKA in RFC 5247 only explained how the
Session-Id is derived for regular authentication. Jouni reported it as
an errata with text explaining how to derive it during fast
reauthentication.
This patch now exports the Session-Id for EAP-AKA during fast
reauthentication based on this Session-Id = 0x17 || NONCE_S || MAC
construction.
Also documented by Alan Dekok in draft-dekok-emu-eap-session-id.
Signed-off-by: Mohit Sethi <mohit.sethi@aalto.fi>
The Session-Id derivation for EAP-SIM in RFC 5247 only explained how the
Session-Id is derived for regular authentication. Jouni reported it as
an errata with text explaining how to derive it during fast
reauthentication.
This patch now exports the Session-Id for EAP-SIM during fast
reauthentication based on this Session-Id = 0x12 || NONCE_S || MAC
construction.
Signed-off-by: Mohit Sethi <mohit.sethi@aalto.fi>
The rcons[] and Td4s[] array values need to be type cast explicitly to
u32 for the left shift 24 operation to be defined due to the implicit
conversion to int not handling the case where MSB would become 1 without
depending on UB.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=14929
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The IE header length check was off-by-one and that could allow the loop
to read one octet beyond the end of the buffer before breaking out in
the second check.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=14927
Fixes: 0a66ce3c49 ("WNM: Add support for SSID List element matching")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The bootstrapping URI format for DPP was extended during protocol design
to allow a list of channels without having to repeat the same operating
class information for each channel. That change was not included in the
initial implementation of the parser and a channel-list like
"C:81/1,6,11" would not be understood correctly (i.e., only the longer
"C:81/1,81/6,81/11" form would have been parsed correctly).
Fix this by extending the parser to accept both the shorter and longer
form for a list of channels within a single operating class.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE Std 802.11ai-2016 requires the FILS STA to do this check, but this
was missing from the initial implementation. The AP side behavior was
not described properly in 802.11ai due to a missing change in the
(Re)Association Response frame format tables which has resulted in some
deployed devices not including the RSNE.
For now, use an interoperability workaround to ignore the missing RSNE
and only check the payload of the element if it is present in the
protected frame. In other words, enforce this validation step only with
an AP that implements FILS authentication as described in REVmd while
allowing older implementations to skip this check (and the protection
against downgrade attacks). This workaround may be removed in the future
if it is determined that most deployed APs can be upgraded to add RSNE
into the (Re)Association Response frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This AP behavior was missing from IEEE Std 802.11ai-2016, but it is
needed for the RSNE validation to work correctly and for a FILS STA to
be able to perform the mandatory check for RSNE matching when processing
the (Re)Association Response frame (as described in 802.11ai). REVmd
will be updating the standard to cover this AP case, so prepare the
implementation to match that. Without this, a FILS STA might reject
association whenever using FILS authentication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
