The full SD Response frame is not going to be followed by another Action
frame from the peer, so remove the 200 ms wait time from the offchannel
TX command in that case. This avoids leaving a 200 ms lock on the radio
to remain on the channel unnecessarily.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is apparently possible for the NL80211_CMD_UNEXPECTED_4ADDR_FRAME
event to be delivered to hostapd before the NL80211_CMD_FRAME_TX_STATUS
event for (Re)Association Response frame. This resulted in the 4-address
WDS mode not getting enabled for a STA. This could occur in particular
when operating under heavy load and the STA is reconnecting to the same
AP in a sequence where Deauthentication frame is followed immediately by
Authentication frame and the driver event processing gets delayed due to
removal of the previous netdev taking time in the middle of this
sequence.
Fix this by recording a pending item for 4-address WDS enabling if the
NL80211_CMD_UNEXPECTED_4ADDR_FRAME event would have been dropped due to
incompleted association and then process this pending item if the TX
status for the (Re)Association Response frame is received and it shows
that the frame was acknowledged.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This registers a new callback to indicate change in SIM state. This
helps to do some clean up (more specifically pmksa_flush) based on the
state change of the SIM. Without this, the reconnection using the cached
PMKSA could happen though the SIM is changed.
Currently eap_proxy_sim_state corresponds to only SIM_STATE_ERROR. This
can be further extended.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The eapol_cb structure was made const and that change resulted in a
compilation warning/error if CONFIG_EAP_PROXY=<name> is enabled in the
wpa_supplicant build configuration. Fix this by updating the function
prototype to match the change.
Note: This results in a change needed to external eap_proxy_*.c
implementations to match the change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit c93b7e1888 ('RSN: Check result of
EAPOL-Key frame send request') forgot to update two PeerKey users of
EAPOL-Key TX functions. That resulted in STK handshake failing since
message 2/4 and 4/4 TX calls were assumed to have failed when the return
value was changed from 0 to a positive value for success case. This
resulted in not updating nonce information properly and hitting
following error when processing STK 4-way handshake message 3/4:
RSN: INonce from message 1 of STK 4-Way Handshake differs from 3 of STK
4-Way Handshake - drop packet (src=<addr>)
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 6d014ffc6e ('Make struct
wpa_eapol_key easier to use with variable length MIC') forgot to update
number of EAPOL-Key processing steps for SMK and STK exchanges and broke
PeerKey. Fix this by updating the Key Data field pointers to match the
new style with variable length Key MIC field.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter fils_realm=<realm> can now be
used to configure one or more FILS realms to advertise for ERP domains
when using FILS. This replaces the use of erp_domain=<domain> parameter
for the FILS use case.
Signed-off-by: Jouni Malinen <j@w1.fi>
P802.11ai/D7.0 changed from CRC32 to SHA256 as the hash algorithm for
the FILS realm name. Update the implementation to match that change.
Signed-off-by: Jouni Malinen <j@w1.fi>
This updates definitions for Status Codes, Reason Codes,
Information Element IDs, Action frame categories, Public Action
codes, Protected Dual of Public Action codes, Advertisement
Protocol ID, and ANQP info IDs based on IEEE Std 802.11-2016.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes both the Probe Response and Beacon frame IEs available to
upper layers if scan results include both IE sets. When the BSS command
mask includes WPA_BSS_MASK_BEACON_IE, a new beacon_ie=<hexdump> entry
will be included in output if the BSS entry has two separate sets of IEs
(ie=<hexdump> showing the Probe Response frame contents and
beacon_ie=<hexdump> the Beacon rame contents).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the secondary channel was not found at all, no debug print was shown
to indicate that the channel was rejected due to that problem. Print a
clearer message indicating which channel was behind the reason to reject
channel configuration as unsuitable for AP mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant control interface commands PMKSA_GET and
PMKSA_ADD that can be used to store PMKSA cache entries in an external
persistent storage when terminating a wpa_supplicant process and then
restore those entries when starting a new process. The previously added
PMKSA-CACHE-ADDED/REMOVED events can be used to help in synchronizing
the external storage with the memory-only volatile storage within
wpa_supplicant.
"PMKSA_GET <network_id>" fetches all stored PMKSA cache entries bound to
a specific network profile. The network_id of the current profile is
available with the STATUS command (id=<network_id). In addition, the
network_id is included in the PMKSA-CACHE-ADDED/REMOVED events. The
output of the PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration in seconds>
<akmp> <opportunistic>
For example:
02:00:00:00:03:00 113b8b5dc8eda16594e8274df4caa3d4 355e98681d09e0b69d3a342f96998aa765d10c4459ac592459b5efc6b563eff6 30240 43200 1 0
02:00:00:00:04:00 bbdac8607aaaac28e16aacc9152ffe23 e3dd6adc390e685985e5f40e6fe72df846a0acadc59ba15c208d9cb41732a663 30240 43200 1 0
The PMKSA_GET command uses the following format:
<network_id> <BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration
in seconds> <akmp> <opportunistic>
(i.e., "PMKSA_ADD <network_id> " prefix followed by a line of PMKSA_GET
output data; however, the reauth_time and expiration values need to be
updated by decrementing them by number of seconds between the PMKSA_GET
and PMKSA_ADD commands)
For example:
PMKSA_ADD 0 02:00:00:00:03:00 113b8b5dc8eda16594e8274df4caa3d4 355e98681d09e0b69d3a342f96998aa765d10c4459ac592459b5efc6b563eff6 30140 43100 1 0
PMKSA_ADD 0 02:00:00:00:04:00 bbdac8607aaaac28e16aacc9152ffe23 e3dd6adc390e685985e5f40e6fe72df846a0acadc59ba15c208d9cb41732a663 30140 43100 1 0
This functionality is disabled be default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option. It should be
noted that this allows any process that has access to the wpa_supplicant
control interface to use PMKSA_ADD command to fetch keying material
(PMK), so this is for environments in which the control interface access
is restricted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These allow external program to monitor PMKSA cache updates in
preparation to enable external persistent storage of PMKSA cache.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd didn't send "TERMINATING" event when stopped by
SIGTERM. Android handles this event to stop monitor thread.
This commit adds "TERMINATING" event same as with wpa_supplicant.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
This allows the vendor scan to be optimized when a response is needed
only from a single, known BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit documents the QCA vendor commands 61-73 and the
corresponding definitions of the attributes. This set of commands were
previously reserved for QCA without documentation here.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These thresholds values indicate how many Beacon frames can be missed
before before disconnecting from the AP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit c79238b6a4 ('Define a QCA vendor
command to configure SAR Power limits') had a mismatch between the enum
qca_vendor_attr_sar_limits_selections documentations and actual values.
The BDF SAR profiles are 0-based, so rename the enum values and reorder
the values keep the actual values more convenient. While this changes
values over the interface, this is justifiable since the new command was
introduced only recently and it had not been released in any driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is to handle the case when peer changes device name and same needs
to be updated to upper layers by P2P-DEVICE-FOUND event. It is similar
to the case when a peer changes wfd_subelems and P2P-DEVICE-FOUND event
goes to upper layers.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
When a peer device stops sending wfd_subelems, wpa_supplicant should
remove dev->info.wfd_subelems from peer's properties. Previously,
wpa_supplicant left the previously learned dev->info.wfd_subelems in
place whenever the new message did not include wfd_subelems.
In addition to fixing the clearing of the old wfd_subelems, this
resolves another issue. As "wfd_changed" variable becomes true even when
peer stops sending wfd_subelems and dev->info.wfd_subelems has an old
value, a new P2P-DEVICE-FOUND event notification was sent again and
again to upper layers whenever a new discovery response was received
from the peer that previously advertised WFD subelements.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Previously, this flag was cleared only in case of failed GO Negotiation.
That could leave the flag set for a peer and if a new group formation
was performed with the same peer before the entry expired, there was
increased risk of getting stuck in a state where neither peer replied to
a GO Negotiation Request frame if a GO Negotiation Response frame with
Status 1 was dropped.
The error sequence could happen in the go_neg_with_bss_connected test
case when timing was suitable to make the second GO negotiation drop a
pending TX Action frame if the GO Negotiation Response with Status 1 was
scheduled for transmission during a P2P scan and P2P_CONNECT was issued
before that scan got aborted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is a regulatory requirement for Specific Absorption Rate (SAR)
whereby the device transmit power is reduced when it is determined that
the device is in close proximity to the body. Implement a vendor command
interface to allow a userspace entity to dynamically control the SAR
power limits.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, os_sleep() was used to block the hostapd (or wpa_supplicant
AP/P2P GO mode) processing between sending out EAP-Failure and
disconnecting the STA. This is not ideal for couple of reasons: it
blocks all other parallel operations in the process and it leaves a
window during which the station might deauthenticate and the AP would
have no option for reacting to that before forcing out its own
Deauthentication frame which could go out after the STA has already
started new connection attempt.
Improve this design by scheduling an eloop timeout of 10 ms instead of
the os_sleep() call and perform the delayed operations from the eloop
callback function. This eloop timeout is cancelled if the STA
disconnects or initiates a new connection attempt before the 10 ms time
is reached. This gets rid of the confusing extra Deauthentication frame
in cases where the STA reacts to EAP-Failure by an immediate
deauthentication.
Signed-off-by: Jouni Malinen <j@w1.fi>
On a connect nl80211 event, wpa_supplicant uses
wpa_driver_nl80211_get_ssid() to fetch the current associated SSID to
compare to existing configurations. However,
wpa_driver_nl80211_get_ssid() uses drv->ssid, which is a cached value.
It is set when we explicitly initial a connect request using
wpa_supplicant. If the association was initiated outside of
wpa_supplicant, we need another way to populate drv->ssid. This commit
sets drv->ssid based on cfg80211 BSS information on connect/associate
nl80211 events.
Signed-off-by: Ningyuan Wang <nywang@google.com>
Commit adcd7c4b0b ('nl80211: Support
vendor scan together with normal scan') made the drv->scan_state updates
for NL80211_CMD_NEW_SCAN_RESULTS and NL80211_CMD_SCAN_ABORTED
conditional on drv->last_scan_cmd being NL80211_CMD_TRIGGER_SCAN. This
missed the part about the possibility of last_scan_cmd == 0 and an
externally started cfg80211 scan is ending. This could leave
drv->scan_state into SCAN_STARTED state even after the scan was
completed. Consequently, hwsim test cases could get stuck in reset()
handler waiting for scan to terminate.
Fix this by updating drv->scan_state also in drv->last_scan_cmd == 0
case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for nl80211 NL80211_CMD_SET_MULTICAST_TO_UNICAST
command.
By setting the new hostapd configuration option multicast_to_unicast=1,
hostapd configures this AP to perform multicast to unicast conversion.
When enabled, all multicast packets with ethertype ARP, IPv4, or IPv6
(possibly within an 802.1Q header) will be sent out to each station once
with the destination (multicast) MAC address replaced by the station's
MAC address. Note that this may break certain expectations of the
receiver, e.g., the ability to drop unicast IP packets encapsulated in
multicast L2 frames, or the ability to not send destination unreachable
messages in such cases.
This also does not implement Directed Multicast Service (DMS).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
We should unconditionally remove inactivity timers for wired network
cases. This commit checks for this after a new station association:
hapd->iface->drv_flags & WPA_DRIVER_FLAGS_WIRED
and then cancels the timeout and does not register a new one.
It prints out a debug message like this:
1476740180.276286: IEEE 802.1X: 00:02:00:00:00:07 CTRL_DIR entering
state FORCE_BOTH
1476740180.276295: hostapd_new_assoc_sta: canceled wired ap_handle_timer
timeout for 00:02:00:00:00:07
This was tested on a debian jessie amd64 system with a configured 120
second inactivity timer and the session did not timeout.
Signed-off-by: Sam Tannous <stannous@cumulusnetworks.com>
Do not use the generic bss_info_handler() design to fetch all scan
results into temporary memory buffer. Instead, use a separate BSS info
handler that fetches the requested information without fully parsing the
BSS entries and without allocating any memory for collecting all the
results.
This is also simplifying bss_info_handler() and nl80211_parse_bss_info()
design by getting rid of the special case that was used only for
nl80211_get_assoc_freq() and not normal scan result fetching.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of fetching all scan results to a temporary buffer, debug print
scan result dump directly from the message handler function one BSS at a
time.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a single scan result to be parsed at a time. This is a step
towards optimizing scan result fetching without having to allocate
memory for all entries at the same time.
Signed-off-by: Jouni Malinen <j@w1.fi>
The way the removal of duplicated (one per frequency) BSS entries in the
cfg80211 scan results were removed in driver_nl80211_scan.c
bss_info_handler() depended on having the full scan results available to
allow iteration through the other entries. This is problematic for the
goal of being able to optimize memory allocations for scan result
fetching in a manner that would not build the full result buffer in
memory.
Move this duplicate removal into bss.c since it has sufficient
information available for doing the same determination of which one of
two BSS entries is more current.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_priv did not yet support Beacon frame IEs (res->beacon_ie_len) which
resulted in invalid scan data being accepted in driver_privsep.c. Add
support for res->beacon_ie_len and also fix the validation step to take
this new variable length field into account.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a single scan result to be checked at a time. This is a step
towards optimizing scan result fetching without having to allocate
memory for all entries at the same time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This untangles the NL80211_CMD_GET_SURVEY handler loop from
NL80211_CMD_GET_SCAN processing so that the per-channel noise
information can be fetched with a common function to a local data
structure that can then be easily used to update individual scan results
(a single BSS) instead of having to go through a full set of scan
results. This is a step towards optimizing scan result fetching without
having to allocate memory for all entries at the same time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Data connection was lost if a station reassociated without the STA entry
being cleaned up on the AP side. Fix this by moving reconfiguration of
the STA WDS parameters in association response callback to happen only
after the STA flags have been updated to associated stated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These are used only within driver_wired_common.c now at the end of the
refactoring changes, so there is no need to make these helper functions
available outside driver_wired_common.c.
Signed-off-by: Jouni Malinen <j@w1.fi>
This uses libnl3 to communicate with the macsec module available on
Linux. A recent enough version of libnl is needed for the macsec.h file
(which is not yet available in a formal libnl release at the time of
this commit).
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This continues refactoring of the common parts of wired drivers code
into a shared file, so that they can be reused by other drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Refactor the common parts of wired drivers code into a shared file, so
that they can be reused by other drivers. The macsec_qca driver already
contains a lot of code duplication from the wired driver, and the
macsec_linux driver would do the same. A structure to hold data common
to all wired drivers is added and used in all these drivers.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This commit enhances the abort scan implementation to also abort the
vendor scan, if one was used to trigger the scan.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN command can be used to
abort an ongoing scan that was started with
QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes a regression from commit
bb598c3bdd ('AP: Add support for full
station state'). That commit added code to remove and re-add the kernel
STA entry when processing Authentication frames with a driver that
advertises support for full AP client state. That resulted in bypassing
PMF protections for unprotected Authentication frames with such drivers
since the TK was lost in this operation.
It is simplest to skip the STA entry clearing in this type of case
completely to leave the TK in place and to process the new
authentication exchange otherwise normally. This matches the behavior
used with the drivers that do not implement full AP client state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11-2012, 12.4.2 states that if an MDE is present in an
(Re)Association Request frame but the RSNE uses a non-FT AKM suite, the
AP shall reject the association using status code 43 ("Invalid AKMP").
wpa_validate_wpa_ie() now explicitly checks for this condition to meet
this requirement instead of simply ignoring the MDE based on non-FT AKM.
Signed-off-by: Will Glynn <will@willglynn.com>
If the driver advertises support for setting Beacon frame data rate,
allow the user to configure this rate as part of starting the AP. Only
one Beacon frame TX rate is allowed.
Drivers advertising such support should set corresponding flag via the
NL80211_ATTR_EXT_FEATURES attribute.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow configuration of Beacon frame TX rate from hostapd.conf with
"beacon_rate=xx" option. The following format is used to set
legacy/HT/VHT beacon rates:
Legacy (CCK/OFDM rates):
beacon_rate=<legacy rate in 100 kbps>
HT:
beacon_rate=ht:<HT MCS>
VHT:
beacon_rate=vht:<VHT MCS>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, wpa_supplicant only supported hardcoded port == 1 in the
SCI, but users may want to choose a different port.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
So that the user can turn encryption on (MACsec provides
confidentiality+integrity) or off (MACsec provides integrity only). This
commit adds the configuration parameter while the actual behavior change
to disable encryption in the driver is handled in the following commit.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
The first peer may take a long time to come up. In PSK mode we are
basically in a p2p system, and we cannot know when a peer will join the
key exchange. Wait indefinitely, and let the administrator decide if
they want to abort.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This commit fixes the nl80211 driver call get_inact_sec() to return -1
when STA inactivity time retrieval fails in i802_read_sta_data().
This was intended to be handled by initalizing the inactive_msec member
to -1 but i802_read_sta_data() assumes the data parameter is
uninitialized and memsets the entire structure, neutralizing the attempt
to distinguish between no value (-1) and a time value of 0.
This is fixed by now requiring i802_read_sta_data() callers to
initialize the data structure first (allowing get_inact_sec() to use
-1). This is a safe change because it does not change any driver API
behavior and only affects one other static function in driver_nl80211.c
Signed-off-by: Joel Cunningham <joel.cunningham@me.com>
In commit a25e4efc9e ('mka: Add driver op
to get macsec capabilities') I added some code to check the driver's
capabilities. This commit has two problems:
- wrong enum type set in kay->macsec_confidentiality
- ignores that drivers could report MACSEC_CAP_NOT_IMPLEMENTED, in
which case the MKA would claim that MACsec is supported.
Fix this by interpreting MACSEC_CAP_NOT_IMPLEMENTED in the same way as a
DO_NOT_SECURE policy, and set the correct value in
kay->macsec_confidentiality.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This extends the anqp_elem configuration parameter support for new Info
IDs (270 (TDLS Capability) was previously missed from the list of
defined values, 280 has already been assigned in REVmc/D8.0; 281..299
are yet to be assigned). No additional source code changes are needed to
allow hostapd to advertise support for these if the ANQP-element value
is set with the anqp_elem parameter.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, CONFIG_IEEE80211R enabled build that supports FT for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode FT is required and there is no need for AP mode FT.
Add support to differentiate between station mode FT and AP mode FT in
wpa_supplicant builds by adding CONFIG_IEEE80211R_AP that should be used
when AP mode FT support is required in addition to station mode FT. This
allows binary size to be reduced for builds that require only the
station side FT functionality.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The Channel Center Frequency Segment subfields use the channel index
instead of frequency in MHz.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
The return value from this function may be used in an outgoing message,
so use a valid status code instead of -1.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add a configuration option in hostapd.conf and in neighbor report that
sets an AP as stationary. To enable this option on the current AP set
the config option stationary_ap to 1. To set a neighbor entry to be
marked as stationary add the word stat to the SET_NEIGHBOR command. This
option tells hostapd to send LCI data even if it is older than requested
by max age subelement in RRM request.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
It is possible that a LCI or location civic configuration buffer
is valid but contains no data. In such a case do not add the LCI
and location civic information to the entry in the neighbor
data base.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
struct data_key already had a 'user' field for reference counting, but
it was basically unused.
Add an ieee802_1x_kay_use_data_key() function to take a reference on a
key, and use ieee802_1x_kay_deinit_data_key() to release the reference.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Document some data structures from IEEE Std 802.1X-2010, and add the
(not used yet) struct ieee802_1x_mka_dist_cak_body.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This is specific to the macsec_qca driver. The core implementation
shouldn't care about this, and only deal with the complete secure
channel, and pass this down to the driver.
Drivers that have such limitations should take care of these in their
->create functions and throw an error.
Since the core MKA no longer saves the channel number, the macsec_qca
driver must be able to recover it. Add a map (which is just an array
since it's quite short) to match SCIs to channel numbers, and lookup
functions that will be called in every place where functions would get
the channel from the core code. Getting an available channel should be
part of channel creation, instead of being a preparation step.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
This has already been done for WEP, but there's same constraint for not
allowing VTH rates in case of TKIP.
Signed-off-by: Filip Matusiak <filip.matusiak@tieto.com>
Receiving a provision discovery request for an ASP service that
has auto accept set to false should result in a provision discovery
response with the status field set to "currently unavailable".
Having stale P2PS provision data, results in sending a response with
the status set to success because it is mistakenly referred to as the
follow-on provision discovery request.
Fix that by clearing stale P2PS provision data in the following cases:
1. When provision discovery is complete
2. When ASP services are flushed (in which case old ASP provisioning
is no longer valid).
Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
drv->in_listen should be cleared whenever the state timeout is cleared,
if they were set together. If the flag is not cleared, the
p2p_listen_end() called during cancel-remain-on-channel will not restart
the search, relying on the state timeout function to do it. Use the
p2p_stop_listen_for_freq() function to clear the listen state properly.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Otherwise, if a P2PS provision is incomplete before the flush, it can
cause incorrect provision responses to be sent out.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Add signal level information to the station tracking information. Also
make it available via the "TRACK_STA_LIST" control command.
Signed-off-by: Kevin Mahoney <k.mahoney@cablelabs.com>
ext_capab/ext_capab_len do not include ID and Length so no extra +2
offset should be used. This fixes a regression from commit
faf427645a ('TDLS: Use proper IE parsing
routine for non-EAPOL-Key cases') that replaced the IE parser without
noticing the difference in the pointer offset.
Signed-off-by: Flavia Vanetti <flavia.vanetti@ceva-dsp.com>
When channel switch happens, driver wrapper's internal channel
information needs to be updated so that the new frequency will be used
in operations using drv->assoc_freq. Previously, only bss->freq was
updated and the new frequency was also indicated in the EVENT_CH_SWITCH
event. This could potentially leave out couple of cases that use
drv->assoc_freq at least as a fallback mechanism for getting the current
operating frequency.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds a control interface command to configure the TDLS
trigger mode to the host driver. This TDLS mode is configured through
the "SET tdls_trigger_control" control interface command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These attributes were previously maintained elsewhere. This commit moves
them to follow the standard assignment process through the qca-vendor.h
file in hostap.git.
Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
Add a new vendor attribute config to set the reorder blocksize and
timeout in 4 ACs, and then report the frame aggregation failure
statistics in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command. In addition,
fix the spelling of the enum value for this subcommand.
Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
This sends the FILS KEK and AAD context (nonces) to the driver with the
NL80211_CMD_ASSOCIATE messages when using FILS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_remove_ptk() call to wpa_auth_set_key() more consistent
with all the other calls that verify the return value to keep static
analyzers happier.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"GET_CAPABILITY fils" used to return "FILS" based on wpa_supplicant
configuration. This can be made more useful by checking both for
wpa_supplicant and driver support for FILS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Decrypt the AES-SIV protected elements and verify Key-Auth. Parse and
configure keys to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the FILS KEK and AAD data (nonces) to be configured to the
driver for association so that the driver can encrypt the
(Re)Association Request frame and decrypt the (Re)Association Response
frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements processing of FILS Authentication frame for FILS shared
key authentication with ERP and PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
ieee802_1x_encapsulate_radius() and ieee802_1x_alloc_eapol_sm() need to
be called from FILS processing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a PMKSA cache entry for the target AP is available, try to use FILS
with PMKSA caching.
If an ERP key for the target AP is available, try to use FILS with
EAP-Initiate/Re-auth added as Wrapper Data element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This needs to be callable through the EAPOL supplicant wrappers to allow
FILS implementation to use ERP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements Key-Auth derivation for (Re)Association Request frames
(see P802.11ai/D11.0 12.12.2.6.2) and (Re)Association Response frames
(see P802.11ai/D11.0 12.12.2.6.3).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is the PTKSA key derivation used as part of the FILS authentication
exchange. See P802.11ai/D11.0 12.12.2.5.3.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it cleaner for the FILS implementation to use the same design
for setting Authentication frame elements as was already done with SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add operations to allow low level control over RF sectors in QCA DMG
(11ad) chipsets. Operations include getting/setting the configuration of
a specific sector, as well as getting/setting the selected sector which
the HW uses to communicate with a specific station.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
That function does not need the full EAP header -- it only needs to know
which EAP identifier to use in the message. Make this usable for cases
where the previous EAP message may not exist (FILS).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This changes 4-way handshake authenticator processing to decrypt the
EAPOL-Key frames using an AEAD cipher (AES-SIV with FILS AKMs) before
processing the Key Data field. This replaces Key MIC validation for the
cases where AEAD cipher is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This changes 4-way handshake authenticator processing to decrypt the
EAPOL-Key frames using an AEAD cipher (AES-SIV with FILS AKMs) before
processing the Key Data field. This replaces Key MIC validation for the
cases where AEAD cipher is used. This needs to move the EAPOL-Key msg
2/4 RSN element processing to happen only after the PTK has been derived
and validated. That is done for all AKMs to avoid extra complexity with
having to maintain two code paths for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This modifies wpa_eapol_key_send() to use AEAD cipher (AES-SIV for FILS
AKMs) to provide both integrity protection for the EAPOL-Key frame and
encryption for the Key Data field. It should be noted that this starts
encrypting the Key Data field in EAPOL-Key message 2/4 while it remains
unencrypted (but integrity protected) in non-FILS cases. Similarly, the
empty Key Data field in EAPOL-Key message 4/4 gets encrypted for AEAD
cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This will be needed to be able to implement AEAD cipher support from
FILS that will need to use KEK to protect the frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Suite B 192-bit addition from IEEE Std 802.11ac-2013 replaced the
previous fixed length Key MIC field with a variable length field. That
change was addressed with an addition of a new struct defined for the
second MIC length. This is not really scalable and with FILS coming up
with a zero-length MIC case for AEAD, a more thorough change to support
variable length MIC is needed.
Remove the Key MIC and Key Data Length fields from the struct
wpa_eapol_key and find their location based on the MIC length
information (which is determined by the AKMP). This change allows the
separate struct wpa_eapol_key_192 to be removed since struct
wpa_eapol_key will now include only the fixed length fields that are
shared with all EAPOL-Key cases in IEEE Std 802.11.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Calculate the hashed realm from hostapd erp_domain configuration
parameter and add this to the FILS Indication element when ERP is
enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If FILS is enabled, indicate that in Beacon, Probe Response, and
(Re)Association Response frames in the Extended Capabilities element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
