Commit graph

103 commits

Author SHA1 Message Date
Sunil Dutt
9ddba3a309 Rename vendor attribute DISABLE_OFFCHANNEL to RESTRICT_OFFCHANNEL
This commit renames the vendor attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_OFFCHANNEL to
QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL as intended by the
original commit d506c35efc ('Set Wi-Fi
Configuration attribute to restrict offchannel operations').

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-26 13:18:06 +03:00
Sunil Dutt
d506c35efc Set Wi-Fi Configuration attribute to restrict offchannel operations
This commit defines an attribute to
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION -
QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL which can be used to
restrict offchannel operations on the AP/GO interface.

The goal is to restrict any operations which would cause the AP/GO to
leave its operating channel.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-23 00:10:01 +03:00
Vidyullatha Kanchanapally
e8e430fe7a Vendor attributes to retain connection on a roam request failure
This commit introduces the following two attributes to
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH events:

QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS - Indicates the status of
	re-association requested by user space
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION - Indicates whether
	the old association was maintained when a re-association
	is requested by user space and that re-association attempt
	fails (i.e., cannot connect to the requested BSS, but can
	remain associated with the BSS with which the association was
	in place when being requested to roam).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-12 00:39:00 +03:00
Sunil Dutt
33117656e6 Define a QCA vendor attribute to update the listen interval
This commit defines an attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL which allows the currently
used listen interval to be updated using
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION. This update applies
only during the association and is done without updating the AP about
the change.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-10 23:58:46 +03:00
Sunil Dutt
8befe8a993 Define a QCA attribute to specify the PCL policy for external ACS
This commit defines an attribute
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to signify the preferred
channel list policy for external ACS.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-20 22:49:08 +03:00
Peng Xu
16217e13d8 QCA vendor commands and attributes for spectral scan
Add new vendor commands for starting and stoppping spectral scan. Add
vendor attributes for configuring spectral scan parameters as part of
the start command.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-06 17:34:13 +03:00
Zhaoyang Liu
1275958873 QCA vendor command: Add TA max duration attribute for OCB configure
Add attribute for TA max duration after last TA received. So that local
time is synchromous to other communicating OCB STAs. If the duration
expires, OCB STA without UTC time source is not in sync to other STAs
and stop scheduling DSRC channel switch after max duration.

Signed-off-by: Zhaoyang Liu <zhaoyang@codeaurora.org>
Signed-off-by: Ferry Zhou <tianguiz@codeaurora.org>
2017-03-27 17:19:38 +03:00
Zhaoyang Liu
2a9ec7c69c Define attributes for QCA vendor OCB commands
Document QCA vendor OCB commands about IEEE Std 802.11 communication
outside the context of a basic service set. Also define all attributes
for the specific OCB commands.

Signed-off-by: Zhaoyang Liu <zhaoyang@codeaurora.org>
Signed-off-by: Ferry Zhou <tianguiz@codeaurora.org>
2017-03-27 17:17:03 +03:00
lifeng
6c2056abe5 QCA vendor attributes to extend antenna diversity functionality
1. Add new attribute to report corresponding antenna information to the
chain RSSI which is used in subcmd
QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI.

2. Add a series of attr to support the new wmi interface
WMI_PDEV_PARAM_ANT_DIV_USRCFG which export parameters setting of antenna
diversity algorithm to userspace.

Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
2017-03-15 21:30:00 +02:00
Zhang Qian
b4ae5f04dc Add vendor attribute to config propagation delay's absolute value
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY is added to set
propagation delay's absolute value. This is a more detailed version of
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY.

Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
2017-03-15 21:24:25 +02:00
Dmitry Shmidt
7f5f4e46ac Fix QCA_ATTR_NUD_STATS_IS_DAD value
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2017-03-14 21:11:18 +02:00
Alexei Avshalom Lazar
160dca0784 Add QCA vendor command/attr for BRP antenna limit control
Add QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT for setting the number
of antennas that will be active in different modes for each connection.

Signed-off-by: Alexei Avshalom Lazar <qca_ailizaro@qca.qualcomm.com>
2017-03-02 15:05:46 +02:00
Gaole Zhang
21ac782797 QCA nl80211 vendor attribute for specific sub-20 MHz channel width
Define a new attribute QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH.
This attribute can set a station device to work in 5 or 10 MHz channel
width while in disconnect state.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-01 11:55:04 +02:00
Peng Xu
7785c70bbb QCA vendor command for fetching HE capabilities
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-19 17:39:30 +02:00
Jouni Malinen
09a97eb27e Update the copyright notice years for QCA vendor definitions
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-04 17:05:30 +02:00
Sunil Dutt
841e9a8c73 QCA vendor command to set the trace levels for the specific QCA module
This commit introduces the vendor command to set the trace level
for the respective QCA host driver module.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-04 17:05:21 +02:00
Kanchanapally, Vidyullatha
70407ee5c3 Add QCA vendor definitions for BSS transition status
Introduce definitions for QCA vendor specific subcommands and attributes
for fetching BSS transition status.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-30 22:31:46 +02:00
Sunil Dutt
a9491695b3 QCA vendor command to set/get NUD statistics
This commit introduces QCA vendor commands and the corresponding
attributes to set/get NUD (Network Unreachability Detection) statistics.
The set NUD statistics configures the requisite parameters to the host
driver and thereby triggers the start/stop of collection of statistics.
The get stats fetches the statistics collected in the host driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-30 01:54:30 +02:00
Sunil Dutt
d7d0f909f1 QCA vendor command to carry the reason for power save failure
This commit defines a QCA vendor command
QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE that carries required
information leading to the power save failure. This will be an event
from the host driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-23 18:47:16 +02:00
Purushottam Kushwaha
4c4070005a QCA vendor command to enable host driver offload ACS to user space
This commit introduces the QCA vendor command and the attributes which
facilitate the host driver to use an external user space entity for
performing automatic channel selection.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-23 06:32:59 +02:00
Jouni Malinen
a2aa21a3bf Assign additional vendor specific elements for early HE testing
These elements can be used for pre-standard publication testing of HE
before P802.11ax draft assigns the element ID extension. The payload of
these vendor specific elements is defined by the latest P802.11ax draft.
Please note that the draft is still work in progress and the element
payload is subject to change.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-13 15:05:26 +02:00
Sunil Dutt
444930e5b6 Define an attribute to do a specific BSSID QCA vendor scan
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-11 21:36:13 +02:00
Sunil Dutt
cea761472a Add QCA vendor command definitions for IDs 61-73
This commit documents the QCA vendor commands 61-73 and the
corresponding definitions of the attributes. This set of commands were
previously reserved for QCA without documentation here.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-11 21:32:20 +02:00
Sunil Dutt
cb0cc6efa6 Define QCA Beacon miss threshold attributes for 2.4 and 5 GHz bands
These thresholds values indicate how many Beacon frames can be missed
before before disconnecting from the AP.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-11 21:11:41 +02:00
Jouni Malinen
c313c8a5d8 Fix QCA vendor command values for SAR power limits
Commit c79238b6a4 ('Define a QCA vendor
command to configure SAR Power limits') had a mismatch between the enum
qca_vendor_attr_sar_limits_selections documentations and actual values.
The BDF SAR profiles are 0-based, so rename the enum values and reorder
the values keep the actual values more convenient. While this changes
values over the interface, this is justifiable since the new command was
introduced only recently and it had not been released in any driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-11 21:08:25 +02:00
Jeff Johnson
c79238b6a4 Define a QCA vendor command to configure SAR Power limits
There is a regulatory requirement for Specific Absorption Rate (SAR)
whereby the device transmit power is reduced when it is determined that
the device is in close proximity to the body. Implement a vendor command
interface to allow a userspace entity to dynamically control the SAR
power limits.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-08 18:56:02 +02:00
Sunil Dutt
1a793f5c2b Define a QCA vendor command to abort vendor scan
The new QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN command can be used to
abort an ongoing scan that was started with
QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-11-30 17:11:01 +02:00
Peng Xu
5e785a6792 Reserve QCA vendor specific nl80211 command 144
This is reserved for QCA use.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-11-17 16:00:59 +02:00
Sunil Dutt
14cd203fff QCA vendor command to configure the TDLS behavior in the host driver
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-27 23:12:25 +03:00
lifeng
a18563d428 Extend QCA vendor attribute link layer statistics attribute
This adds new statistics attributes to support channel hopping feature.

Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
2016-10-27 22:05:59 +03:00
lifeng
95f3703ae1 Add more QCA vendor attribute definitions into qca-vendor.h
These attributes were previously maintained elsewhere. This commit moves
them to follow the standard assignment process through the qca-vendor.h
file in hostap.git.

Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
2016-10-27 22:03:33 +03:00
lifeng
87416eaf64 QCA vendor attribute to report frame aggregation failure
Add a new vendor attribute config to set the reorder blocksize and
timeout in 4 ACs, and then report the frame aggregation failure
statistics in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command. In addition,
fix the spelling of the enum value for this subcommand.

Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
2016-10-27 21:46:04 +03:00
Lior David
6eb1a569ca Add QCA vendor command/attr for low level DMG(11ad) RF sector control
Add operations to allow low level control over RF sectors in QCA DMG
(11ad) chipsets. Operations include getting/setting the configuration of
a specific sector, as well as getting/setting the selected sector which
the HW uses to communicate with a specific station.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-10-17 11:43:57 +03:00
Lior David
32d08d5bf6 Add QCA vendor attributes for measurement frequency for FTM/AOA
Add attributes for specifing the frequency where FTM/AOA measurement is
done over the air. This allows the user space framework to maintain its
own cache of peers without depending on the kernel scan results cache,
or perform scans less often (since entries in the kernel scan results
cache expire quickly). The change is backward compatible. If the
frequency attribute is not specified, the kernel scan results cache will
be queried, like done today.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-10-04 23:44:18 +03:00
Sunil Dutt
8b6688847e Add explicit enum values for QCA vendor config attributes
This makes it easier to copy a subset of definitions without
accidentally getting mismatching values.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-09-30 22:45:03 +03:00
lifeng
8b7c5b8941 QCA vendor command for antenna diversity feature
The user space app use QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI cmd to
get the corresponding antenna rssi value for the specific chain. And the
associcated attributes are added to configure the antenna diversity and
related selftest.

Signed-off-by: Li Feng <lifeng@qti.qualcomm.com>
2016-09-26 23:46:59 +03:00
vamsi krishna
2800ec85d2 MBO: Add QCA vendor option to configure driver to ignore assoc disallow
MBO capable APs can set association disallowed in the Beacon/Probe
Response frames. For testing purposes, the STA needs to be configured to
not ignore the association disallowed set by APs and continue to connect
to such AP like non-MBO enabled STA. Add a QCA vendor attribute for
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION vendor sub command to
configure the driver to ignore association disallowed functionality.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-09-25 17:31:26 +03:00
Zhang Qian
320caeab29 Add attributes for QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT
More attributes are added for QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT
1. Peer signal stats;
2. Peer TX stats;
3. Peer RX stats

Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
2016-09-23 21:13:58 +03:00
Srinivas Dasari
0d7eba5417 Define a QCA vendor command to validate encryption engine
This command carries 802.11 header and payload along with key (TK) and
PN for encryption/decryption purpose. Firmware/driver encrypts/decrypts
the given data and sends to userspace as a response to the command. User
space component can validate the data received from the driver to unit
test the hardware's encryption engine.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-09-22 20:30:05 +03:00
Lior David
a62dea4156 Fix mistakes in definition of QCA vendor commands for indoor location
Fix some mistakes in the previous commit for adding QCA vendor commands
for indoor location.

Note: The renamed enum value does not change the ABI, but the addition
of QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID in the beginning of enum
qca_wlan_vendor_attr_ftm_meas does renumber
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_* values. The previous values were
committed yesterday and have not been used in any released code yet, so
this is a justifiable quick fix.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-09-06 23:38:47 +03:00
Lior David
fcd85d9a3f Add QCA vendor commands/attributes for indoor location
Assign QCA vendor specific commands, attributes, and events for
supporting indoor location features.

These features include:

1. Fine timing measurement (FTM) - allows measurement of distance
between two stations. Based on IEEE P802.11-REVmc/D7.0, 11.24.6 FTM is
performed between two stations: one is an initiator, typically a client
that wants to measure distance to another AP, and one is a responder,
typically an AP which responds to measurement requests from other
clients. The responder can be configured to report its location, either
in absolute coordinates (LCI) or free-form description (LCR).

2. Angle of arrival (AOA) - allows measurement of azimuth and elevation
between two stations.

The above features can be combined to allow a station to get an accurate
indoor location.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-09-05 21:59:18 +03:00
Zhang Qian
22950d0568 QCA vendor subcommand for LL_STATS extension
Some user space monitor wants to offload link layer statistics to
firmware. A new command QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT and
associcated attributes are added. The monitor will use this new command
to configure monitoring paramters and get link layer statistics.
Attributes added in this change:
1. Parameters for FW to trigger the statistics report
2. Peer STA power state
3. TX failure statistics

Signed-off-by: Zhang Qian <zhangq@qti.qualcomm.com>
2016-09-05 20:50:10 +03:00
Yingying Tang
6fe3b9d451 QCA vendor command to get hardware capabilities
This commit introduces a new vendor sub command
QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY and the associated
attributes to get Wi-Fi hardware capabilities.

Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
2016-08-10 16:49:46 +03:00
Sunil Dutt
dc24a3616a Define an attribute QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER
This can be used to enable/disable QPOWER.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-08-09 19:23:25 +03:00
Sunil Dutt
fed802c2e8 Define an attribute QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX
This can be used to set the configuration parameters per netdev (instead
of wiphy).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-08-04 21:50:26 +03:00
Sunil Dutt
14b7612447 Define vendor command to support IE based access control
This commit defines QCA vendor subcommand and attributes for IE based
access control, i.e., the specific configured IE (full IE) is matched
with the frames originated by the Wi-Fi STA / AP to accept or deny the
connection. A specific IE can either be a whitelist or blacklist.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-08-04 21:50:22 +03:00
Vikram Kandukuri
4ac75cd01a QCA vendor command to configure GPIO pins
This commit introduces a new vendor sub command
QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND and associated
attributes to configure GPIO pins.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-08-03 16:46:30 +03:00
Vikram Kandukuri
babf0ce0d2 Assign QCA vendor attributes for generic commands
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-08-03 16:44:07 +03:00
Jouni Malinen
4f910f38e5 Fix a typo in QCA vendor attribution documentation
The previously used subcommand names in the comment did not match the
ones defined above.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-08-02 21:11:25 +03:00
vamsi krishna
ab21863108 Define QCA vendor config attribute to set default scan IEs to the driver
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-08-02 21:11:05 +03:00