sae_check_confirm_pk() and sae_write_confirm_pk() were using different
checks for determining whether SAE-PK was used. It was apparently
possible to miss the checks in sae_write_confirm_pk() in some AP cases
where SAE H2E is being used. Fix this by checking sae->pk in the
write-confirm case similarly to the way this was done in check-confirm.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Debug logs did not make it clear whether the failure happens when
checking a received SAE confirm or when writing own SAE confirm. Those
cases have different checks on when to go through SAE-PK processing, so
it is useful to make this part clear in the debug log.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not use red color for the "No response receive" message in case
another HR will be sent after this.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Fix processing of the case where no handover select is sent out and add
automatic (delayed) termination of the link on completing the handover
successfully.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
terminate_now was not being set in the only_one case with connection
handover. Set it for that case as well as the tag cases to automatically
close down the link once it is not needed anymore.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use a shorter polling interval in recv_octets() to be able to send out
the alternative HR more quickly when using a single thread and handover
client. In addition, fix recv_records() to handle normal exception cases
like not receiving anything.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Postpone closing of the handover client to allow the same client to be
used for sending both handover request messages if an alternative URI
needs to be tried.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Set logging level to various upper layer nfcpy modules to enable more
detailed debugging of the actual NFC operations when requested (-d on
the command line).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify AES-CTR encryption implementation against the test vectors in
NIST SP 800-38a. This implementations was already tested against AES SIV
and EAX mode test vectors, but this adds more explicit testing against
published CTR mode test vectors.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not try to perform DPP operations on the P2P management interface
when no specific interface has been identified.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If an alternative proposal (second handover request) is sent, the
response (or lack of it) to the initial handover request should be
ignored.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This avoids potential loops of endless alternative URI exchanges over
NFC negotiated connection handover. Only allow one such alternative
proposal and declarare the handover as a failure if another alternative
were needed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow all actual DPP processing steps in wpa_supplicant to be skipped by
specifying hardcoded URI values. Also allow a hardcoded crn to be
specified to force specific handover requestor/selector roles.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use the "tmp_disallow" name more consistently so that both the core
wpa_supplicant functionality (struct wpa_bss_tmp_disallowed) and the
wpa_driver_ops callback have more similar names.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
remove_on_tx_status needs to be set in this case even if
dpp_config_processing=2 is used since there will be no connection
attempt when receiving a Configurator backup instead of station config
object.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
For now, this is done only for the case where the NFC Device is not
usable and if writing a single tag fails.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make the debug output easier to read when performing interactive NFC
operations on a device that has a terminal showing the log.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The change to checking DPP_LISTEN return value ended up overwriting the
actual URI information from wpas_get_nfc_uri().
Fixes: 288c0ffaaa ("dpp-nfc: Do not hardcode netrole for NFC Tag writing cases")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow netrole to be specified for NFC Tag writing cases. Previously,
this was hardcoded to use netrole=configurator when starting the listen
operation. Now the netrole parameter is not included by default, but any
netrole value can be specified with the new --netrole command line
argument.
In addition, fix the listening frequency for the case where a channel is
picked.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce a new attribute QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE
to configure access category override for UDP frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduces a vendor command to get the currently enabled band(s)
through QCA_NL80211_VENDOR_SUBCMD_GETBAND.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Also introduce a new attribute QCA_WLAN_VENDOR_ATTR_SETBAND_MASK to
carry this new bitmask enum. This attribute shall consider the bitmask
combinations to define the respective band combinations and substitutes
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE. The old attribute use remains same
as before.
In addition, document the previously undocumented, but defined,
QCA_NL80211_VENDOR_SUBCMD_SETBAND.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The NL80211_ATTR_VLAN_ID attribute expects non-zero values, but vlan_id
with value 0 has been set in VLAN offload case. Due to this, station
connection failure is observed if the driver advertises VLAN_OFFLOAD
support:
nl80211: NL80211_ATTR_STA_VLAN (addr=8c:fd:f0:22:19:15 ifname=wlan0
vlan_id=0) failed: -34 (Result not representable)
wlan0: STA 8c:fd:f0:22:19:15 IEEE 802.11: could not bind the STA
entry to vlan_id=0
Fix this by setting only non-zero values.
Fixes: 0f903f37dc ("nl80211: VLAN offload support")
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
40/80 MHz bandwidth setting was being rejected due to incorrect sanity
check on the channel index. Fix that for the bandwidths larger than 20
MHz.
Fixes: d7c2c5c98c ("AP: Add initial support for 6 GHz band")
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
When removing a mesh peer with control interface commands (ACCEPT_ACL
DEL_MAC/DENY_ACL ADD_MAC/MESH_PEER_REMOVE) the plink count was not
decreased from its last connection. This resulted in peer link count
leakage and wpa_supplicant rejecting the connections after reaching
max_peer_links (default: 99).
Fix this by decreasing the plink count when removing a mesh peer which
is in PLINK_ESTAB state.
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
wpa_s->dpp_auth did not get cleaner if dpp_config_processing=1 is used.
Clear this after having received TX status for Configuration Result to
avoid leaving behind the completed provisioning instance.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The pending authentication exchange will make us ignore Reconfig
Authentication Request, so do not allow reconfiguration to be started in
that state.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The 0..3 value decoded from the password was not incremented to the
actual 2..5 range for Sec. This resulted in not properly detecting the
minimum password length.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The use of the alternative channel list did not work properly for the
case were both ends were trying to initiate the negotiated connection
handover. Fix this by always starting a new connection handover client
thread for sending the alternative proposal and ignoring peer messages
(likely something from the first attempt) during this modified attempt.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When a PMKSA cache entry is available and used for connection with FILS
key management suite, use FILS authentication algorithm for connection
even if ERP keys are not available. This scenario may happen when
applications using wpa_supplicant cache persistently only PMKSA but not
ERP keys and reconfigures wpa_supplicant with PMKSA cache after
restarting wpa_supplicant.
The previous implementation correctly handles SME-in-wpa_supplicant
cases. However, SME-in-driver cases, complete FILS authentication
without PMKSA caching is performed.
Fix SME-in-driver behavior by setting authentication algorithm to
WPA_AUTH_ALG_FILS when connecting to a FILS AP using PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The channel numbering/center frequencies was changed in IEEE
P802.11ax/D6.1. The center frequencies of the channels were shifted by
10 MHz. Also, a new operating class 136 was defined with a single
channel 2. Add required support to change the channelization as per IEEE
P802.11ax/D6.1.
Signed-off-by: Wu Gao<wugao@codeaurora.org>
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
