Introduce additional attributes for the TWT response parameters from the
host driver. Also, add ATTR_TWT_RESUME_FLOW_ID for TWT Resume request.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update the SAE-PK implementation to match the changes in the protocol
design:
- allow only Sec values 3 and 5 and encode this as a single bit field
with multiple copies
- add a checksum character
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows the testing command GET_PMK to return a PMK in cases where
the association fails (e.g., when using SAE and getting a valid PMKSA
entry added before association) or after the association has been lost.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add override parameters to use the specified channel while populating
OCI element in EAPOL-Key group msg 2/2, FT reassoc request, FILS assoc
request and WNM sleep request frames.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
The documentation for the QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE
attribute had incorrectly specified the value of 0 (corresponding to BE)
to disable the QoS upgrade. BK (1) is a lower priority AC compared to BE
and if BE is used to disable the upgrade, there would be no possibility
for configured UDP AC upgrade to replace BK-from-DSCP with BE. Thus,
correct this by specifying that the value of BK (1) is used to disable
this UDP AC upgrade.
Fixes: ebd5e764f9 ("Vendor attribute to configure QoS/AC upgrade for UDP frames")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
sae_check_confirm_pk() and sae_write_confirm_pk() were using different
checks for determining whether SAE-PK was used. It was apparently
possible to miss the checks in sae_write_confirm_pk() in some AP cases
where SAE H2E is being used. Fix this by checking sae->pk in the
write-confirm case similarly to the way this was done in check-confirm.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Debug logs did not make it clear whether the failure happens when
checking a received SAE confirm or when writing own SAE confirm. Those
cases have different checks on when to go through SAE-PK processing, so
it is useful to make this part clear in the debug log.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not use red color for the "No response receive" message in case
another HR will be sent after this.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Fix processing of the case where no handover select is sent out and add
automatic (delayed) termination of the link on completing the handover
successfully.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
terminate_now was not being set in the only_one case with connection
handover. Set it for that case as well as the tag cases to automatically
close down the link once it is not needed anymore.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use a shorter polling interval in recv_octets() to be able to send out
the alternative HR more quickly when using a single thread and handover
client. In addition, fix recv_records() to handle normal exception cases
like not receiving anything.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Postpone closing of the handover client to allow the same client to be
used for sending both handover request messages if an alternative URI
needs to be tried.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Set logging level to various upper layer nfcpy modules to enable more
detailed debugging of the actual NFC operations when requested (-d on
the command line).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify AES-CTR encryption implementation against the test vectors in
NIST SP 800-38a. This implementations was already tested against AES SIV
and EAX mode test vectors, but this adds more explicit testing against
published CTR mode test vectors.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not try to perform DPP operations on the P2P management interface
when no specific interface has been identified.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If an alternative proposal (second handover request) is sent, the
response (or lack of it) to the initial handover request should be
ignored.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This avoids potential loops of endless alternative URI exchanges over
NFC negotiated connection handover. Only allow one such alternative
proposal and declarare the handover as a failure if another alternative
were needed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow all actual DPP processing steps in wpa_supplicant to be skipped by
specifying hardcoded URI values. Also allow a hardcoded crn to be
specified to force specific handover requestor/selector roles.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use the "tmp_disallow" name more consistently so that both the core
wpa_supplicant functionality (struct wpa_bss_tmp_disallowed) and the
wpa_driver_ops callback have more similar names.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
remove_on_tx_status needs to be set in this case even if
dpp_config_processing=2 is used since there will be no connection
attempt when receiving a Configurator backup instead of station config
object.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
For now, this is done only for the case where the NFC Device is not
usable and if writing a single tag fails.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make the debug output easier to read when performing interactive NFC
operations on a device that has a terminal showing the log.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The change to checking DPP_LISTEN return value ended up overwriting the
actual URI information from wpas_get_nfc_uri().
Fixes: 288c0ffaaa ("dpp-nfc: Do not hardcode netrole for NFC Tag writing cases")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow netrole to be specified for NFC Tag writing cases. Previously,
this was hardcoded to use netrole=configurator when starting the listen
operation. Now the netrole parameter is not included by default, but any
netrole value can be specified with the new --netrole command line
argument.
In addition, fix the listening frequency for the case where a channel is
picked.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce a new attribute QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE
to configure access category override for UDP frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduces a vendor command to get the currently enabled band(s)
through QCA_NL80211_VENDOR_SUBCMD_GETBAND.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Also introduce a new attribute QCA_WLAN_VENDOR_ATTR_SETBAND_MASK to
carry this new bitmask enum. This attribute shall consider the bitmask
combinations to define the respective band combinations and substitutes
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE. The old attribute use remains same
as before.
In addition, document the previously undocumented, but defined,
QCA_NL80211_VENDOR_SUBCMD_SETBAND.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The NL80211_ATTR_VLAN_ID attribute expects non-zero values, but vlan_id
with value 0 has been set in VLAN offload case. Due to this, station
connection failure is observed if the driver advertises VLAN_OFFLOAD
support:
nl80211: NL80211_ATTR_STA_VLAN (addr=8c:fd:f0:22:19:15 ifname=wlan0
vlan_id=0) failed: -34 (Result not representable)
wlan0: STA 8c:fd:f0:22:19:15 IEEE 802.11: could not bind the STA
entry to vlan_id=0
Fix this by setting only non-zero values.
Fixes: 0f903f37dc ("nl80211: VLAN offload support")
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
40/80 MHz bandwidth setting was being rejected due to incorrect sanity
check on the channel index. Fix that for the bandwidths larger than 20
MHz.
Fixes: d7c2c5c98c ("AP: Add initial support for 6 GHz band")
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
When removing a mesh peer with control interface commands (ACCEPT_ACL
DEL_MAC/DENY_ACL ADD_MAC/MESH_PEER_REMOVE) the plink count was not
decreased from its last connection. This resulted in peer link count
leakage and wpa_supplicant rejecting the connections after reaching
max_peer_links (default: 99).
Fix this by decreasing the plink count when removing a mesh peer which
is in PLINK_ESTAB state.
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
wpa_s->dpp_auth did not get cleaner if dpp_config_processing=1 is used.
Clear this after having received TX status for Configuration Result to
avoid leaving behind the completed provisioning instance.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The pending authentication exchange will make us ignore Reconfig
Authentication Request, so do not allow reconfiguration to be started in
that state.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
