This allows the IKE groups 27-30 (RFC 6932) to be used with OpenSSL
1.0.2 and newer. For now, these get enabled for SAE as configurable
groups (sae_groups parameter), but the new groups are not enabled by
default.
Signed-off-by: Jouni Malinen <j@w1.fi>
draft-irtf-cfrg-dragonfly recommends implementation to set the security
parameter, k, to a value of at least 40. This will make PWE generation
take significantly more resources, but makes it more likely to hide
timing differences due to different number of loops needed to find a
suitable PWE.
Signed-off-by: Jouni Malinen <j@w1.fi>
This check explicitly for reflection attack and stops authentication
immediately if that is detected instead of continuing to the following
4-way handshake that would fail due to the attacker not knowing the key
from the SAE exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
OpenSSL 0.9.8 (and newer) includes SSL_CTX_get_app_data() and
SSL_CTX_set_app_data(), so there is no need to maintain this old
OPENSSL_SUPPORTS_CTX_APP_DATA backwards compatibility design.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, it would have been possible for va_end(args) to be called
twice in case mp_init() fails. While that may not cause issues on number
of platforms, that is not how va_start()/va_end() are supposed to be
used. Fix this by returning from the function without using va_end()
twice on the same va_list args.
Signed-off-by: Jouni Malinen <j@w1.fi>
The construction used here to figure out the offset of variable length
IEs in Probe Request frames was a bit odd looking and resulted in a
warning from a static analyzer, so replace it with more standard use of
offsetof().
Signed-off-by: Jouni Malinen <j@w1.fi>
The flags argument is used to indicate a failure case (0x80) which
allows erp == NULL. This may be a bit too difficult combination for
static analyzers to understand, so add an explicit check for !erp as
another condition for returning from the function before the erp pointer
gets dereferenced without checking it.
Signed-off-by: Jouni Malinen <j@w1.fi>
drv cannot be NULL here (it is dereferenced even on the preceding line)
and anyway, os_free(NULL) is allowed, so remove the redundant check.
Signed-off-by: Jouni Malinen <j@w1.fi>
The eap argument to this function is never NULL and the earlier
ieee802_1x_learn_identity() call is dereferencing it anyway, so there is
no point in checking whether it is NULL later in the function.
Signed-off-by: Jouni Malinen <j@w1.fi>
This needs to find the PRI channel also in cases where the affected
channel is the SEC channel of a 40 MHz BSS, so need to include the
scanning coverage here to be 40 MHz from the center frequency. Without
this, it was possible to miss a neighboring 40 MHz BSS that was at the
other end of the 2.4 GHz band and had its PRI channel further away from
the local BSS.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to have separate return statements for these corner
cases that are unlikely to be hit in practice.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the common WLAN-* RADIUS attributes were added only when WPA
or WPA2 was used. These can be of use for OSEN as well, so include them
in that case, too.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to have a separate "fail silently" case for wpa_ie_len
== 0. That condition does not seem to be reachable and even if it were,
the following "ie len too short" case will result in the exact same
return value.
Signed-off-by: Jouni Malinen <j@w1.fi>
As far as IEEE 802.11 standard is concerned, WEP is deprecated, but at
least in theory, allowed as a group cipher. This option is unlikely to
be deployed anywhere and to clean up the implementation, we might as
well remove all support for this combination.
Signed-off-by: Jouni Malinen <j@w1.fi>
Sending a wowlan configuration command can be done on any wireless
interface (not only netdev), as it is a device configuration and not
interface configuration specific. Fix the code to allow it to be
sent on any interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Android libnl_2 implementation added support for "nl80211" name in
commit 'libnl_2: Extend genl_ctrl_resolve() to support "nl80211" name'
in July 2012 which got included in Android 4.2. It is fine to drop this
old Android ICS workaround from wpa_supplicant now.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
p2p_process_nfc_connection_handover() allocates msg memory in the parser
and might return before memory is released if the received message is
not valid.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
If key derivation fails, there is no point in trying to continue
authentication. In theory, this could happen if memory allocation during
TLS PRF fails.
Signed-off-by: Jouni Malinen <j@w1.fi>
Free tmp_out before returning to prevent memory leak in case the second
memory allocation in openssl_tls_prf() fails. This is quite unlikely,
but at least theoretically possible memory leak with EAP-FAST.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
org.wi-fi.wfds service is not a replacement for non-WFA service matches.
Do not try to replace the results with that if there is not sufficient
room for the response. Instead, reply with all the matching services
that fit into the message. org.wi-fi.wfds is the first entry in the list
(if matching request/service is present), so it won't get overridden by
other services.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The service hash for org.wi-fi.wfds is supposed to match only if the
device has a WFA defined org.wi-fi.wfds.* service. Verify that before
adding org.wi-fi.wfds to the response.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Probe Response building is already doing service matching and there is
no need to do this in both places, so simplify the p2p_reply_probe()
implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When doing initial processing of Probe Request frame service hashes, the
previous implementation dropped all other hash values if a hash for
org.wi-fi.wfds was included. This is not correct, since that is not a
full wildcard of all services (it only matches WFA defined
org.wi-fi.wfds.* services).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This "wildcard" match is for WFA specified org.wi-fi.wfds.* services,
not for all services. Verify that there is a really matching service
being advertised instead of assuming this "wildcard" matches if any
services are advertised.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The org.wi-fi.wfds "wildcard" is not a full wildcard of all service
names and as such, it must not remove other service name hash values
from the Probe Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
p2ps_gen_hash() has a limit on service names based on the temporary
buffer from stack. Verify that the service name from the local P2P_FIND
command is short enough to fix into that buffer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Quoting P2PS specification: "If multiple Service Hash values are
included in the Probe Request frame, then the ASP shall find a match for
each Service Hash, and it shall send a Probe Response frame with the
information listed in this section for all matched Service Hashes." This
commit changes handling of wildcard hash matching by adding a
wildcard 'org.wi-fi.wfds' info together with the other hash matches.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add auxiliary functions to write a single advertised service info record
into a wpabuf and to find P2PS wildcard hash in a received hash
attribute. Re-factor p2p_buf_add_service_instance() function to allow
adding new wildcard types in future commits.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When hostapd or wpa_supplicant is run in debug more with key material
prints allowed (-K on the command line), it is possible for passwords
and keying material to show up in debug prints. Since some of the debug
cases end up allocating a temporary buffer from the heap for processing
purposes, a copy of such password may remain in heap. Clear these
temporary buffers explicitly to avoid causing issues for hwsim test
cases that verify contents of memory against unexpected keys.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Avoid using p2p_data::query_hash for both Probe Request frame processing
and for hashes specified by p2p_find. It's resolved by use of local
query_hash and query_count variables in p2p_reply_probe().
Since p2p_data::query_hash is used only for seek hash values rename
p2p_data::query_hash to p2ps_seek_hash.
Delete p2p_data::query_count since it's not needed anymore.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Commit 86bd36f0d5 ('Add generic mechanism
for adding vendor elements into frames') introduced a mechanism to add
vendor elements into various frames, but missed the addition to the
Invitation Response frame. This commit addresses the same.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This variable is used locally only in the p2p_reply_probe() function.
The value of this variable is valid only in the context of the single
Probe Request message handling and doesn't make much sense in p2p
context.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Free a PD context with a function encapsulating both os_free() call and
setting a PD context pointer to NULL.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
A P2P Client may be discoverable and reply to Probe Request frames,
while at the same time the P2P GO would also be discoverable and include
the P2P Client information in the P2P Group Info attribute of the Probe
Response frames.
If a seeker constantly hears the Probe Response frames from a P2P Client
and then from the GO, but handles them in the opposite order (due to
scan results ordering), the more valuable Probe Response frame from the
P2P Client will be ignored. Fix this by defining a threshold (1 second)
during which the direct Probe Response frame will be preferred over the
information acquired from the GO and will not be considered as old.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When adding group clients to the P2P peer list, use the driver provided
BSS entry timestamp instead of the current time. Otherwise, the time
comparison which is made in p2p_add_device() doesn't make sense.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
If the RX frequency of the Probe Request frame is known, specify it when
sending the Probe Response frame. This is needed when the Probe Request
frame is received on another virtual interface, for example, when a GO
or P2PS client are discoverable on the group operating channel.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Change send_mlme() API to allow sending management frames on a specific
channel, overriding the internal driver decision.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Return P2P_PREQ_PROCESSED instead of P2P_PREQ_NOT_PROCESSED on
a successful Probe Request frame handling in p2p_reply_probe().
Verify a return value of p2p_reply_probe() in p2p_probe_req_rx()
and continue a pending invitation/connection flow only if the
Probe Request frame is from an expected P2P peer.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
In some cases, Probe Request frames can be received by a peer not only
on a listen channel. In this case an additional rx_freq parameter
explitly contains a Probe Request frame RX frequency. In case rx_freq is
set to 0, a Probe Request frame RX channel is assumed to be our own
listen channel (p2p->cfg->channel).
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
CA country code was included mistakenly (copy-paste..) in cn_op_class_cc
while it was supposed to be included only in us_op_class_cc. In
practice, this did not result in incorrect operation due to the
us_op_class_cc list being checked first. Anyway, better fix
cn_op_class_cc to avoid confusion here.
Signed-off-by: Jouni Malinen <j@w1.fi>
This increases code coverage for gas.c testing to cover areas that
cannot be reached with pure hwsim test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Currently, if multiple bss share are bridge and tagged vlan interface,
only the first instance of struct hostapd_vlan for this vlanid will have
the DVLAN_CLEAN_VLAN flag added. Thus, when this instance is removed,
the tagged vlan interface will be removed from bridge, thought other bss
might still need it. Similarily, the bridge will be left over, as the
does not have zero ports when the first instance of a struct
hostapd_vlan is freed.
This patch fixes this by having a global (per process) reference counter
for dynamic tagged vlan and dynamically created bridge interfaces, so
they are only removed after all local users are freed. (struct
hapd_interfaces *)->vlan_priv is used to hold src/ap/vlan_init.c global
per-process data like drv_priv does; right now this is only used for the
interface reference counting, but could get extended when needed. Then
possibly some vlan_global_init / vlan_global_deinit should be added, but
this is not required right now.
Additionally, vlan->configured is checked to avoid reference counter
decreasing before vlan_newlink increased them.
In order to avoid race conditions, vlan_dellink is called explicitly
after hostapd_vlan_if_remove. Otherwise there would be a short timeframe
between hostapd_vlan_if_remove and vlan_dellink during which the struct
hostapd_vlan still exists, so ap_sta_bind_vlan would try to attach
stations to it.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Add operating class 125 (channels 149..169) to the list of P2P supported
channels. This allows the 5 GHz channels 161 and 169 to be used for P2P
GO when those channels are allowed for AP mode in the current regulatory
domain.
Signed-off-by: Amr BEN ABDESSALEM <amrx.ben.abdessalem@intel.com>
Instead of an int variable with magic values 0, 1, 2, use an enum that
gives clearer meaning to the values now that the original boolean type
global argument is not really a boolean anymore.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 95b6bca66d ('Add rsn_pairwise bits
to set_ieee8021x() driver_ops') modified cipher configuration to use
unconditionally wpa_pairwise | rsn_pairwise. While that works for many
cases, it does not handle the case of dynamic configuration changes over
the control interface where wpa_pairwise or rsn_pairwise values may not
get cleared when the wpa parameter is modified. Fix this inconsistency
by configuring the driver with only the bits that are valid for the
currently enabled WPA/WPA2 version(s).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add GO Intent information of connecting device in GO Negotiation Request
event which will help applications to decide its own GO intent value in
advance and can avoid failure cases when both devices use GO Intent 15
depending on application requirement.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
So that systems with bad clocks will send random session IDs,
instead of always ones starting at the same second.
If os_get_random() isn't available, use os_get_time(). But also
mix in now.tv_usec, so that the accounting session ID is more
likely to be globally and temporally unique.
Signed-off-by: Alan DeKok <aland@freeradius.org>
The OPENSSL_VERSION_NUMBER < 0x00909000L case of
openssl_get_keyblock_size() had not been kept in sync with the cleanup
changes.
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Explicitly check for iface->current_mode before dereferencing it. While
this case may not happen in practice, it is better for the setup
functions to be more careful when doing the initial band selection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When device supports dual band operations with offloaded ACS, hw_mode
can now be set to any band (hw_mode=any) in order to allow ACS to select
the best channel from any band. After a channel is selected, the hw_mode
is updated for hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While RFC 6124 does not define how Session-Id is constructed for
EAP-EKE, there seems to be consensus among the authors on the
construction. Use this Type | Nonce_P | Nonce_S construction based on
the following email:
From: Yaron Sheffer <yaronf.ietf at gmail.com>
To: ietf at ietf.org
Date: Wed, 17 Nov 2010 13:13:42 +0200
Expanding on my previous response, I suggest to resolve Bernard's
concern by adding the following text:
5.6 EAP Key Generation
EAP-EKE can be used for EAP key generation, as defined by [RFC 5247].
When used in this manner, the values required to establish the key
hierarchy are defined as follows:
- Peer-Id is the EAP-EKE ID_P value.
- Server-Id is the EAP-EKE ID_S value.
- Session-Id is the concatenated Type | Nonce_P | Nonce_S, where Type is
the method type defined for EAP-EKE in [Sec. 4.1], a single octet.
Thanks,
Yaron
Signed-off-by: Jouni Malinen <j@w1.fi>
The ACS code part of hostapd scans all the channels even if the channel
list is specified in the hostapd.conf. Limit the ACS scan channels to
the list specified in the config file.
Signed-off-by: Srinivasa Duvvuri<sduvvuri@chromium.org>
Do not add a P2P IE when a station interface is trying to associate
to an AP or P2P GO that publishes a P2P IE but does not include
a P2P manageability attribute.
This addresses an interoperability issue that was reported in
https://bugzilla.kernel.org/show_bug.cgi?id=96471, where a P2P GO
rejects association from a station interface without a specified
reason.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Link Property query vendor command shall facilitate the information
of the Wi-Fi link. MAC address of the Wi-Fi peer is given as an input
for querying the link properties.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The cleanup code will handle this, but it is more robust to make sure
this is cleared to zero when allocating a new buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The cleanup code will handle this, but it is more robust to make sure
this is cleared to zero when allocating a new buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The L (Length) and M (More) flags needs to be cleared before deciding
whether the locally generated response requires fragmentation. This
fixes an issue where these flags from the server could have been invalid
for the following message. In some cases, this could have resulted in
triggering the wpabuf security check that would terminate the process
due to invalid buffer allocation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The remaining number of bytes in the message could be smaller than the
Total-Length field size, so the length needs to be explicitly checked
prior to reading the field and decrementing the len variable. This could
have resulted in the remaining length becoming negative and interpreted
as a huge positive integer.
In addition, check that there is no already started fragment in progress
before allocating a new buffer for reassembling fragments. This avoid a
potential memory leak when processing invalid message.
Signed-off-by: Jouni Malinen <j@w1.fi>
The remaining number of bytes in the message could be smaller than the
Total-Length field size, so the length needs to be explicitly checked
prior to reading the field and decrementing the len variable. This could
have resulted in the remaining length becoming negative and interpreted
as a huge positive integer.
In addition, check that there is no already started fragment in progress
before allocating a new buffer for reassembling fragments. This avoid a
potential memory leak when processing invalid message.
Signed-off-by: Jouni Malinen <j@w1.fi>
The length of the received Commit and Confirm message payloads was not
checked before reading them. This could result in a buffer read
overflow when processing an invalid message.
Fix this by verifying that the payload is of expected length before
processing it. In addition, enforce correct state transition sequence to
make sure there is no unexpected behavior if receiving a Commit/Confirm
message before the previous exchanges have been completed.
Thanks to Kostya Kortchinsky of Google security team for discovering and
reporting this issue.
Signed-off-by: Jouni Malinen <j@w1.fi>
The length of the received Commit and Confirm message payloads was not
checked before reading them. This could result in a buffer read
overflow when processing an invalid message.
Fix this by verifying that the payload is of expected length before
processing it. In addition, enforce correct state transition sequence to
make sure there is no unexpected behavior if receiving a Commit/Confirm
message before the previous exchanges have been completed.
Thanks to Kostya Kortchinsky of Google security team for discovering and
reporting this issue.
Signed-off-by: Jouni Malinen <j@w1.fi>
The length of the WMM Action frame was not properly validated and the
length of the information elements (int left) could end up being
negative. This would result in reading significantly past the stack
buffer while parsing the IEs in ieee802_11_parse_elems() and while doing
so, resulting in segmentation fault.
This can result in an invalid frame being used for a denial of service
attack (hostapd process killed) against an AP with a driver that uses
hostapd for management frame processing (e.g., all mac80211-based
drivers).
Thanks to Kostya Kortchinsky of Google security team for discovering and
reporting this issue.
Signed-off-by: Jouni Malinen <j@w1.fi>
The debug information from httpread can be helpful in figuring out error
cases in general and as such, should be enabled by default. Get rid of
the hardcoded httpread_debug value that would require source code
changes to enable.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to continue processing a HTTP body when it becomes
clear that the end result would be over the maximum length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that ncopy parameter to memcpy is not negative. While this is not
supposed to be needed, it is a good additional protection against
unknown implementation issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
strtoul() return value may end up overflowing the int h->chunk_size and
resulting in a negative value to be stored as the chunk_size. This could
result in the following memcpy operation using a very large length
argument which would result in a buffer overflow and segmentation fault.
This could have been used to cause a denial service by any device that
has been authorized for network access (either wireless or wired). This
would affect both the WPS UPnP functionality in a WPS AP (hostapd with
upnp_iface parameter set in the configuration) and WPS ER
(wpa_supplicant with WPS_ER_START control interface command used).
Validate the parsed chunk length value to avoid this. In addition to
rejecting negative values, we can also reject chunk size that would be
larger than the maximum configured body length.
Thanks to Kostya Kortchinsky of Google security team for discovering and
reporting this issue.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the mp_init_multi() call had failed due to memory allocation failure,
mp_div() would have returned 1 instead of MP_MEM (-2). It looks like all
callers are checking the return value against MP_OKAY instead of <1
(etc.), so this does not seem to result in difference in behavior.
Anyway, it's best to fix the mp_div() return value for the MP_MEM error
case to avoid unexpected behavior.
Signed-off-by: Maks Naumov <maksqwe1@ukr.net>
In theory, the previous version could have resulted in reading one byte
beyond the end of the management frame RX buffer if the local driver
were to deliver a truncated Public Action frame for processing. In
practice, this did not seem to happen with mac80211-based drivers and
even if it were, the extra octet would be an uninitialized value in a
buffer rather than read beyond the end of the buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was previously checked as part of the eap_sim_parse_attr()
processing, but it is easier to review the code if there is an
additional explicit check for confirming that the Reserved field is
present since the pos variable is advanced beyond it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Clean up eap_sake_parse_add_attr() design by passing in pointer to the
payload of the attribute instead of parsing these separately for each
attribute within the function.
Signed-off-by: Jouni Malinen <j@w1.fi>
The req_plen argument to eap_pax_process_std_1() and
eap_pax_process_std_3() could be smaller than sizeof(struct eap_pax_hdr)
since the main processing function was only verifying that there is
enough room for the ICV and then removed ICV length from the remaining
payload length.
In theory, this could have resulted in the size_t left parameter being
set to a negative value that would be interpreted as a huge positive
integer. That could then result in a small buffer read overflow and
process termination if MSGDUMP debug verbosity was in use.
In practice, it does not seem to be feasible to construct a short
message that would be able to pass the ICV validation (calculated using
HMAC-SHA1-128) even for the case where an empty password is used.
Anyway, the implementation should really check the length explicitly
instead of depending on implicit check through ICV validation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The EAP-TLS-based helper functions can easily use struct wpabuf in more
places, so continue cleanup in that direction by replacing separate
pointer and length arguments with a single struct wpabuf argument.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function is only using the Identifier field from the EAP request
header, so there is no need to pass it a pointer to the full message.
This makes it a bit easier to analyze the area that gets access to
unverified message payload.
Signed-off-by: Jouni Malinen <j@w1.fi>
MS-MPPE-Recv-Key generation in radius_msg_add_mppe_keys() used incorrect
function argument (send_key_len; should be recv_key_len) when allocating
a temporary buffer. Fix this by using the correct argument.
The only caller of the function uses the same length for both
send_key_len and recv_key_len, so this copy-paste error did not result
in any difference in the behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Handling of WPS RF band for 60 GHz was missing. Add it in all relevant
places and also map "AES" as the cipher to GCMP instead of CCMP when
operating on the 60 GHz band.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
It was possible for the WPA_ALG_PMK algorithm in set_key() to result in
trying to configure a key with cipher suite 0. While this results in a
failure from cfg80211 or driver, this is not really desirable operation,
so add a check for cipher suite conversion result before issuing the
nl80211 command.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This can be used with Proxy ARP to allow multicast NAs to be forwarded
to associated STAs using link layer unicast delivery. This used to be
hardcoded to be enabled, but it is now disabled by default and can be
enabled with na_mcast_to_ucast=1. This functionality may not be desired
in all networks and most cases work without it, so the new
default-to-disabled is more appropriate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, struct wpa_group was created when the first station enters
the group and the struct wpa_group was not freed when all station left
the group. This causes a problem because wpa_group will enter
FATAL_FAILURE when a wpa_group is running while the AP_VLAN interface
has already been removed.
Fix this by adding a reference counter to struct wpa_group and free a
group if it is unused.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
If hostapd has bound a STA into a specific VLAN, the new vlan_id
parameter in the control interface STA command can now be used to check
which VLAN ID is in use.
Signed-off-by: Jouni Malinen <j@w1.fi>
All the system header files are supposed to be included before any other
internal header file apart from utils/includes.h.
Signed-off-by: Jouni Malinen <j@w1.fi>
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Now on an engine error we decode the error value and determine if the
issue is due to a true PIN error or not. If it is due to incorrrect PIN,
delete the PIN as usual, but if it isn't let the PIN be.
Signed-off-by: Mike Gerow <gerow@google.com>
Previously, mesh state machine transmits updated Commit Message when
receiving a Confirm Message in Committed state. According to the
standard, it should (re)send the latest Commit Message previously sent.
IEEE Std 802.11-2012, 11.3.8.6.4 Protocol instance behavior - Committed
state:
"Upon receipt of a Con event, ... If Sync is not greater than
dot11RSNASAESync, the protocol instance shall increment Sync, transmit
the last Commit Message sent to the peer, and set the t0
(retransmission) timer."
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends dynamic_vlan=required checks to apply for WPA-PSK with
macaddr_acl=2 (RADIUS) case.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Previously, only P2P and mesh use cases enforced unique MAC address for
a dynamically added virtual interface. Extend this to cover normal
station mode interfaces since those can now be added with INTERFACE_ADD.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to try to derive DH shared key with a peer that tries
to use too short or too long DH Public Key. Previously, such cases ended
up implicitly getting rejected by the DH operations failing to produce
matching results. That is unnecessarily, so simply reject the message
completely if it does not have a Public Key with valid length. Accept
couple of octets shorter value to be used to avoid interoperability
issues if there are implementations that do not use zero-padding
properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
This enforces variable length strings Manufacturer, Model Name, Model
Number, and Serial Number to be within the maximum length defined in the
WSC specification. While none of the existing users for these within
hostapd/wpa_supplicant had problems with longer strings, it is good to
ensure the strings are not longer to avoid potential issues at higher
layer components.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the element is of fixed length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Remove the length field from struct ieee802_11_elems since the only
allowed element length is five and that is checked by the parser.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the only allowed element length is one.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check the element length in the parser and remove the length field from
struct ieee802_11_elems since the only allowed element length is one.
Signed-off-by: Jouni Malinen <j@w1.fi>
All the existing users of these elements were already validating the
element length. However, it is clearer to validate this already at the
parser for extra layer of protection for any future changes.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 88b32a99d3 ('FT: Add FT AP support
for drivers that manage MLME internally') added an alternative way of
processing the WMM TSPEC from RIC. However, that change did not seem to
include the same checks for WMM TSPEC element length that were used in
the original implementation for MLME-in-hostapd case. Fix this by
sharing the older implementation of copying the WMM TSPEC from RIC for
both cases.
It looks like the destination buffer for the response is sufficiently
long for the fixed length copy, but it may have been possible to trigger
a read beyond the end of the FTIE by about 50 bytes. Though, that seems
to be within the buffer received for RX buffer in the case that uses
this driver-based AP MLME design for FT.
Signed-off-by: Jouni Malinen <j@w1.fi>
This program can be used to run fuzzing tests for areas related to EAPOL
frame parsing and processing on the supplicant side.
Signed-off-by: Jouni Malinen <j@w1.fi>
This program can be used to run fuzzing tests for areas related to P2P
message parsing and processing. p2p-fuzzer allows data files to be used
to inject Probe Response and Action frames for processing by the P2P
module.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it more obvious that the wps_parse_msg() bounds checking is
used to verify that there is sufficient space in the P2P buffer for the
secondary device types.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This modifies couple of code segments that replaced control characters
in strings with '_' to use a common helper function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While it looks like all the users of this parsed attribute were able to
handle longer SSID values, there is no valid use case for these and to
avoid any potential future issues, enforce maximum length (32 bytes) on
the SSID during parsing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While it looks like all the users of this parsed attribute were able to
handle longer Device Name values, there is no valid use case for these
and to avoid any potential issues in upper layer components, enforce
maximum length (32 bytes) on the Device Name during parsing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While none of the current users of msg.persistent_ssid{,_len} would have
issues with too long SSID value, it is safer to enforce bounds checking
on the SSID while parsing the attribute to avoid any potential issues in
the future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The SSID element is defined to have a valid length range of 0-32. While
this length was supposed to validated by the users of the element
parser, there are not really any valid cases where the maximum length of
32 octet SSID would be exceeded and as such, the parser itself can
enforce the limit as an additional protection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes a possible memcpy overflow for P2P dev->oper_ssid in
p2p_add_device(). The length provided by the peer device (0..255 bytes)
was used without proper bounds checking and that could have resulted in
arbitrary data of up to 223 bytes being written beyond the end of the
dev->oper_ssid[] array (of which about 150 bytes would be beyond the
heap allocation) when processing a corrupted management frame for P2P
peer discovery purposes.
This could result in corrupted state in heap, unexpected program
behavior due to corrupted P2P peer device information, denial of service
due to process crash, exposure of memory contents during GO Negotiation,
and potentially arbitrary code execution.
Thanks to Google security team for reporting this issue and smart
hardware research group of Alibaba security team for discovering it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The multi-SSID design that used a single beaconing BSSID with multiple
SSIDs was never completed in this repository, so there is no need to
maintain the per-STA ssid/ssid_probe pointers that could only point to
&hapd->conf->ssid. Save some memory and reduce code complexity by
removing this unused partial capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit fa0e715100 ('Use
tls_connection_prf() for all EAP TLS-based key derivation') copied some
pointer checks from the generic implementation to tls_openssl.c.
However, these are arrays and cannot be NULL in OpenSSL data. Remove the
unnecessary checks and add master_key_length check for completeness.
(CID 109619).
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to interpret debug logs for cases where hostapd
control multiple interfaces.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to interpret debug logs in case hostapd controls
multiple interfaces and a STA roams between them.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Currently, vlan_remove_dynamic() is only called when the station VLAN ID
is changed (ap_sta_bind_vlan), but not when the station is freed. So
dynamic VLAN interfaces are not removed actually except within 1x
reauthentification VLAN ID change, although most of the code is already
there.
This patch fixes this by calling vlan_remove_dynamic() in ap_free_sta().
It cannot just use sta->vlan_id for this, as this might have been
changed without calling ap_sta_bind_vlan() (ap/ieee802_11.c:handle_auth
fetches from RADIUS cache for WPA-PSK), thus reference counting might
not have been updated. Additionally, reference counting might get wrong
due to old_vlanid = 0 being passed unconditionally, thus increasing the
reference counter multiple times.
So tracking the currently assigned (i.e., dynamic_vlan counter
increased) VLAN is done in a new variable sta->vlan_id_bound. Therefore,
the old_vlan_id argument of ap_sta_bind_vlan() is no longer needed and
setting the VLAN for the sta in driver happens unconditionally.
Additionally, vlan->dynamic_vlan is only incremented when it actually
is a dynamic VLAN.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
hostapd receives NEWLINK messages multiple times and thus does
configuration of the the vlan interface multiple times.
This is not required and leads to the following during cleanup in
test pmksa_cache_preauth_vlan_used:
1. run-test.py does: brctl delif brvlan1 wlan3.1
2. hostapd processes NEWLINK and does: brctl addif brvlan1 wlan3.1
3. run-test.py does: brctl delbr brvlan1
-> fails as wlan3.1 is still in the bridge
This patch fixes this by ignoring repeated NEWLINK messages.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
When hitting
> Failed to create interface wlan3.1: -23 (Too many open files in system)
> Try to remove and re-create wlan3.1
hostapd deletes the AP_VLAN interface and then recreates it. Thus the
kernel assigns the same ifidx to the new interfaces and sends DELLINK
and NEWLINK mesages.
As the DELLINK messages are processed after the struct hostapd_vlan is
added, hostapd deletes the struct hostapd_vlan entry, deconfigures the
AP_VLAN interface and leaves vlan_newlink nothing to find afterwards.
So this patch makes DELLINK messages to be ignored when the interface
exists.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Previously, during RSN preauthentication, ap_sta_bind_vlan() was called,
which fails for non-zero sta->vlan_id as the station is not known to the
kernel driver.
Fix this by binding the station only if it is associated. If it is not
associated, ap_sta_bind_vlan() will be done later during association.
In addition, reject Access-Accept if the returned VLAN ID is not valid
in the current hostapd configuration.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Both Android's libc and glibc support _FORTIFY_SOURCE, a compiler
and libc feature which inserts automatic bounds checking into
common C functions such as memcpy() and strcpy(). If a buffer
overflow occurs when calling a hardened libc function, the
automatic bounds checking will safely shutdown the program and
prevent memory corruption.
Android is experimenting with _FORTIFY_SOURCE=3, a new fortify
level which enhances memcpy() to prevent overflowing an element
of a struct. Under the enhancements, code such as
struct foo {
char empty[0];
char one[1];
char a[10];
char b[10];
};
int main() {
foo myfoo;
int n = atoi("11");
memcpy(myfoo.a, "01234567890123456789", n);
return 0;
}
will cleanly crash when the memcpy() call is made.
Fixup hostap code to support the new level. Specifically:
* Fixup sha1_transform so it works with the enhanced bounds checking.
The old memcpy() code was attempting to write to context.h0, but that
structure element is too small and the write was extending (by design)
into h1, h2, h3, and h4. Use explicit assignments instead of
overflowing the struct element.
* Modify most of the structures in ieee802_11_defs.h to use ISO C99
flexible array members (https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html)
instead of a zero length array. Zero length arrays have zero length,
and any attempt to call memcpy() on such elements will always overflow.
Flexible array members have no such limitation. The only element not
adjusted is probe_req, since doing so will generate a compile time error,
and it's not obvious to me how to fix it.
Signed-off-by: Nick Kralevich <nnk@google.com>
wpa_ctrl.c gets sys/stat.h inherited from
private/android_filesystem_config.h it should
not rely on this in the future. The intent is
to move fs_config function into libcutils and
thus deprecate any need for sys/stat.h in this
include file.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The internal TLS implementation started rejecting number of unsupported
configuration parameters recently, but those new error paths did not
free the allocated tlsv1_credentials buffer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This function exposes internal state of the TLS negotiated parameters
for the sole purpose of being able to implement PRF for EAP-FAST. Since
tls_connection_prf() is now taking care of all TLS-based key derivation
cases, it is cleaner to keep this detail internal to each tls_*.c
wrapper implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is not needed anymore with the tls_connection_prf() being used to
handle all key derivation needs. tls_connection_get_keys() is a bit
misnamed for now, but it is only used to fetch the client and server
random for Session-Id derivation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
tls_openssl.c is the only remaining TLS/crypto wrapper that needs the
internal PRF implementation for EAP-FAST (since
SSL_export_keying_material() is not available in older versions and does
not support server-random-before-client case). As such, it is cleaner to
assume that TLS libraries support tls_connection_prf() and move the
additional support code for the otherwise unsupported cases into
tls_openssl.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
is_ht_allowed is a confusing name since this variable is used to track
whether 40 MHz channel bandwidth is allowed instead of whether HT is
allowed in general.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds hexdumps of MSCHAP/MSCHAPv2 Challenge and Response in format
used by asleap. This is only enabled for CONFIG_TESTING_OPTIONS=y
builds.
Signed-off-by: Jouni Malinen <j@w1.fi>
If NEED_AP_MLME=y is not defined, compilation might
fail under some configurations:
src/ap/drv_callbacks.c:594:2: warning: implicit declaration of
function ‘hostapd_acs_completed’ [-Wimplicit-function-declaration]
src/ap/sta_info.c:253: undefined reference to `sae_clear_retransmit_timer'
Fix these errors by adding the missing hostapd_acs_completed() stub,
and defining NEED_AP_MLME in case of CONFIG_SAE.
Signed-off-by: Eliad Peller <eliad@wizery.com>
This replaces the internal CBC mode implementation in
aes_128_cbc_encrypt() and aes_128_cbc_decrypt() with the OpenSSL
implementation for CONFIG_TLS=openssl builds.
Signed-off-by: Jouni Malinen <j@w1.fi>
The local buffers may contain information used to generate parts of the
derived key, so clear these explicitly to minimize amount of unnecessary
private key-related material in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
The local hash[] buffer may contain parts of the derived key, so clear
it explicitly to minimize number of unnecessary copies of key material
in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
The local T[] buffer may contain parts of the derived key, so clear it
explicitly to minimize number of unnecessary copies of key material in
memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previous workaround for WEXT events from the Host AP driver required
wlan# and wifi# interfaces to have fixed names with the same number.
While that used to be the common case ten years ago, it is less common
nowadays. Extend this to use sysfs (if available) to figure out the
wifi# interface name if the specified interface is detected to be using
the Host AP driver.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add SQLite error message and DB name to the DB related errors. Add
enough tracing so that users can know exactly where users are failing to
be found.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The new network profile parameter mem_only_psk=1 can be used to specify
that the PSK/passphrase for that network is requested over the control
interface (ctrl_iface or D-Bus) similarly to the EAP network parameter
requests. The PSK/passphrase can then be configured temporarily in a way
that prevents it from getting stored to the configuration file.
For example:
Event:
CTRL-REQ-PSK_PASSPHRASE-0:PSK or passphrase needed for SSID test-wpa2-psk
Response:
CTRL-RSP-PSK_PASSPHRASE-0:"qwertyuiop"
Note: The response value uses the same encoding as the psk network
profile parameter, i.e., passphrase is within double quotation marks.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends EAP-pwd peer support to allow NtHash version of password
storage in addition to full plaintext password. In addition, this allows
the server to request hashed version even if the plaintext password is
available on the client. Furthermore, unsupported password preparation
requests are now rejected rather than allowing the authentication
attempt to continue.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends EAP-pwd server support to allow NtHash version of password
storage in addition to full plaintext password.
Signed-off-by: Jouni Malinen <j@w1.fi>
Old code defaulted to WEP for an AP advertising OSEN. Show as OSEN
instead. Re-use most of the RSN parsing logic since all but the header
is the same.
Example output:
[root@ath9k-f lanforge]# ./local/bin/wpa_cli -i sta0 scan_results
bssid / frequency / signal level / flags / ssid
00:0e:8e:6f:40:49 2462 -23 [OSEN-OSEN-CCMP][ESS] ben-138
Signed-off-by: Ben Greear <greearb@candelatech.com>
HT requires QoS/WMM, so unset HT capabilities for a station
whose association request does not include a valid WMM IE.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This extends NL80211_CMD_ROAM event processing to allow the driver to
roam to another ESS (different SSID) when using offloaded BSS selection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update ACS driver offload feature for VHT configuration. In addition,
this allows the chanlist parameter to be used to specify which channels
are included as options for the offloaded ACS case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Delete all ASP serice advertisement on wpas_p2p_service_flush similarly
to Bonjour and UPnP services.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
There's off-by-one in the range availability check - the case of
first_chan_idx + num_chans == num_channels should be allowed (e.g., 0 +
1 == 1, for the case of a single 20 MHz channel).
Signed-off-by: Maital Hahn <maitalm@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
When looking for a new operating channel, consider the case of
non-contiguous channels when checking all the needed channels (e.g., the
driver might support channels 36, 38, 40, so look for channels 36+40
explicitly, instead of failing when encountering channel 38).
Signed-off-by: Eliad Peller <eliad@wizery.com>
In wiphy_info_handler(), vendor specific commands were
interpreted as QCA specific without checking for the OUI,
which caused incorrect setting of driver flags with
commands from other vendors. As a result, that could
prevent proper operation (e.g., inability to process CSA).
This patch ensures that QCA vendor specific commands are
checked against QCA OUI before related flags are set.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
If the AP/Authenticator receives an EAPOL-Key msg 2/4 for an association
that negotiated use of PSK and the EAPOL-Key MIC does not match, it is
likely that the station is trying to use incorrect PSK/passphrase.
Report this with "AP-STA-POSSIBLE-PSK-MISMATCH <STA addr>" control
interface event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
SChannel/CryptoAPI as a TLS/crypto library alternative was never
completed. Critical functionality is missing and there are bugs in this
implementation. Since there are no known plans of completing this
support, it is better to remove this code.
Signed-off-by: Jouni Malinen <j@w1.fi>
Channel 140 is needed as allowed HT40 channel pair to use
channel 144 introduced in 802.11ac for VHT40 and VHT80.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Handle NL80211_ATTR_EXT_FEATURES attribute and
NL80211_EXT_FEATURE_VHT_IBSS to determine whether
the driver supports VHT with IBSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
It was possible for bitfield_get_first_zero() to read one octet beyond
the allocated bit buffer in case the first zero bit was not within
size-1 first octets.
Signed-off-by: Jouni Malinen <j@w1.fi>
This event was previously used only when disabling AP mode operation
through hostapd control interface. Make this more consistent by
providing same indication when disabling hostapd interface through the
interface deinit path. This adds the event to the case where a full
hostapd radio instance is removed which also applies for the
wpa_supplicant AP mode operations.
Signed-off-by: Jouni Malinen <j@w1.fi>
If OpenSSL reports that a presented leaf certificate is invalid,
but it has been explicitly pinned, accept it anyway.
Signed-off-by: Rohit Agrawal <rohit.agrawal.mn@gmail.com>
Previously, it would have been possible to complete RSN connection by
skipping the msg 3/4 and 4/4 completely. This would have resulted in
pairwise key not being configured. This is obviously not supposed to
happen in practice and could result in unexpected behavior, so reject
group key message before the initial 4-way handshake has been completed.
Signed-off-by: Jouni Malinen <j@w1.fi>
ML80211_ATTR_TDLS_OPERATION can now set to NL80211_TDLS_DISCOVERY_REQ to
allow the driver to request wpa_supplicant to initiate TDLS Discovery
Request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the TDLS operation request mechanism to allow TDLS
Discovery Request to be initiated by the driver similarly to the
existing Setup and Teardown requests.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, it was possible for the wpa_sm_start_preauth() and
wpa_sm_rekey_ptk() eloop callbacks to remain active after disconnection
and potentially continue to be used for the next association. This is
not correct behavior, so explicitly cancel these timeouts to avoid
unexpected attempts to complete RSN preauthentication or to request PTK
to be rekeyed.
It was possible to trigger this issue, e.g., by running the following
hwsim test case sequence: ap_wpa2_ptk_rekey ap_ft_sae_over_ds
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The initial IEEE 802.11 ProxyARP functionality in the kernel needed
changes in behavior and that ended up requiring an independent
configuration parameter to be used. Update hostapd to use that new
proxyarp_wifi parameter instead of the earlier proxyarp.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This converts the QCA vendor event to EVENT_DFS_* events for the case
of DFS offloaded to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Modify the string for AP-CSA-FINISHED event indication to include a flag
which tells the framework whether the new channel is a DFS channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add handling logic for DFS offloaded case, and add a helper function
that takes the frequency (MHz) as a param and returns 1 if given channel
requires DFS, or 0 otherwise.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If DFS is offloaded to the driver, hostapd should not be performing
these operations. Send the relevant control interface events to provide
information to upper layer software that may use such events to track
DFS/CAC state. This makes the offloaded DFS implementation more
consistent with the DFS-in-hostapd behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces a callback to notify any configuration updates
from the eap_proxy layer. This is used to trigger re-reading of IMSI and
MNC length.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a connection with the primary server cannot be established, restore
connection to the previously used server.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 347c55e216 ('RADIUS client: Re-try
connection if socket is closed on retransmit') added a new option for
initialing RADIUS server failover from radius_client_retransmit(), but
ended up trying to change authentication servers when accounting server
was supposed to be changed due to a copy-paste issue.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the GO Negotiation Response (failure) TX status to
be processed at a point where there is no P2P timeout to continue
search. Avoid stopping the ongoing search operation by explicitly
restarting it from this callback.
Signed-off-by: Jouni Malinen <j@w1.fi>
The optional freq=<MHz> can now be used with the P2P_FIND command to
specify a single channel to scan during the first round of P2P search.
For example, this can be used to replace the full initial scan with a
single channel scan of a known operation channel.
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
This reverts commit 3df2f4fe99 ('P2P:
Remove unused P2P_SCAN_SPECIFIC') with a modification to fit the current
code base.
Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
Disable VHT caps for STAs for which there is not even a single
allowed MCS in any supported number of streams. i.e STA is
advertising 3 (not supported) as VHT MCS rates for all supported
streams.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Commit 347c55e216 ('RADIUS client: Re-try
connection if socket is closed on retransmit') added a possibility of
executing RADIUS server failover change within
radius_client_retransmit() without taking into account that this
operation may end up freeing the pending message that is being
processed. This could result in use of freed memory. Avoid this by
checking whether any pending messages have been removed and if so, do
not try to retransmit the potentially freed message.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, send() was called with invalid fd = -1 in some error cases
for retransmission and this could even result in a loop of multiple such
attempts. This is obviously not going to work, so drop such attempts and
instead, try to reconnect a socket to the server if the current socket
is not valid.
In addition, initiate server failover immediately if the current socket
is not valid instead of waiting for a timeout.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the initial attempt at opening the socket connection to the RADIUS
server failed due to missing IP connectivity during startup, e.g., with
"connect[radius]: Network is unreachable", hostapd did not try to
reconnect when RADIUS messages were sent. Instead, it only reported "No
authentication server configured" even if the configuration did have a
server entry.
This was broken by commit 9ed4076673
('RADIUS client: Do not try to send message without socket') for the
initial case and the more recent fixes in RADIUS server failover cases
did not cover the initial failure case.
Signed-off-by: Jouni Malinen <j@w1.fi>
It does not look likely that the old DSA design would be added into the
internal TLS implement, so remove this otherwise dead code.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows wpa_supplicant to recover from some of the cases where
cfg80211 is unloaded and reloaded without restarting wpa_supplicant. The
netlink socket used for nl80211 events (global->nl_event) seemed to end
up in otherwise functionality state, but with all the event memberships
lost when cfg80211 gets reloaded.
There does not seem to be any clear way of determining when this has
happened, so it looks simplest to just try to re-subscribe to all the
events whenever an interface is re-enabled or added.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit e6dd8196e5 ('Work around Linux
packet socket regression') closed the workaround socket on the first
received EAPOL frame from the main packet socket. This can result in
closing the socket in cases where the kernel does not really work in the
expected way during the following initial association since
reauthentication/rekeying using EAPOL frames happens while operstate is
not dormant and as such, the frames can get delivered through the main
packet socket.
Fix this by closing the workaround socket only in case the first EAPOL
frame is received through the main packet socket. This case happens
while the interface is in dormant state and as such, is more likely to
show the more restricted case of kernel functionality.
In order to avoid processing the received EAPOL frames twice, verify a
checksum of the frame contents when receiving frames alternatively from
the main packet socket and the workaround socket.
Signed-off-by: Jouni Malinen <j@w1.fi>
These values were previously used only for sorting the scan results, but
it may be useful to provide access to the used values through the BSS
entries.
Signed-off-by: Jouni Malinen <j@w1.fi>
This modifies the BSS selection routines to calculate SNR and estimated
throughput for each scan result and then use the estimated throughput as
a criteria for sorting the results. This extends the earlier design by
taking into account higher throughput rates if both the AP and local
device supports HT20, HT40, or VHT80. In addition, the maximum rate is
restricted based on SNR.
In practice, this gives significantly higher probability of selecting
HT/VHT APs when there are multiple BSSes in the same ESS and SNR is not
low enough to prevent higher MCS use.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it somewhat easier to use CONFIG_WPA_TRACE=y build with
external programs that might not be aware of the initialization
requirement, e.g., when linking wpa_ctrl.c with a program that does not
use the os_*() wrappers.
Signed-off-by: Jouni Malinen <j@w1.fi>
This change adds the function hostapd_config_clear_wpa_psk() that
deletes an entire wpa_psk structure, making sure to follow the linked
list and to free the allocated memory of each PSK node. This helps to
prevent memory leaks when using PSKs from multiple sources and
reconfiguring the AP during runtime.
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
Configure the GO CTWindow on APstart if the driver supports it and this
parameter is set in wpa_supplicant configuration.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Read p2p_go_ctwindow (0-127 TUs) from the config file, and pass it to
the driver on GO start.
Use p2p_go_ctwindow=0 (no CTWindow) by default.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Some APs (e.g., Cisco 1260) sometimes add padding to the end of short
TDLS management packets and that can look like invalid IEs. This was
allowed on M3 and discovery packets, but not in others. Allow it for the
other packets as well, since required IEs are verified in the code
anyway.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Add fixed_freq=<0/1> network block parameter and pass it to the driver
when starting or joining an IBSS. If this flag is set, IBSS should not
try to look for other IBSS networks to merge with on different channels.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The '/usr/include/libnl3' header path is unsafe for cross-compilation.
Use pkg-config to find libnl-3.0 headers by default and alternatively,
allow LIBNL_INC=<path> to be used in .config to override.
Signed-off-by: Romain Naour <romain.naour@openwide.fr>
These were not supposed to include a newline at the end of the message
text since such formatting gets handled by tls_show_errors(). In
addition, change the message about the issuer's issuer to be more
accurate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If addition of a peer issuer certificate fails, the certs pointer would
be NULL when being passed to sk_X509_push() for peer issuer's issuer.
Fix this by skipping addition of issuer's issue if issuer addition
fails.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If addition of a peer issuer certificate fails, the certs pointer would
be NULL when being passed to sk_X509_push() for peer issuer's issuer.
Fix this by skipping addition of issuer's issue if issuer addition
fails.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When DFS offloading capability is supported by the driver, the driver
should use these events to indicate when a radar pattern has been
detected, channel availability check (CAC) has been completed, aborted
or finished after the non-occupancy period is over on a DFS channel.
Also, add a new driver.h event to be used by NL80211 to indicate CAC
Started event on a DFS channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver indicates that the interface has been disabled, assume
that all associations have been lost and remove the hostapd STA entries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
RTM_NEWLINK event without IFF_UP were processed for all related
interfaces (including VLANs and bridge). While these events may need to
be processed for other purposes, they should not end up claiming that
the main interface has been disabled, so indicate
EVENT_INTERFACE_DISABLED only if the ifname matches the first BSS ifname
for the interface. In addition, fix some of the ifup/down checks from
if_indextoname() cases to actually use the resolved ifname (namebuf)
rather than hardcoding the first configured ifname to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This uses couple of additional helper macros and prints more debug
information to make the VLAN events easier to analyze.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Sending client probe on already removed client from kernel driver does
not have any benefit and may lead unintended behavior among variable
drivers (mac80211 has a WARN_ON() that could have been triggered after
ifconfig down+up earlier when hostapd did not re-enable beaconing on
ifup). Skip this step in discussion when the kernel driver reports that
client entry is removed.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
This allows WPA2 mode AP to be re-enabled automatically after external
ifconfig down + up on a netdev used by hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a step towards enabling hostapd to restart AP mode functionality
if the interface is disabled and re-enabled, e.g., with ifconfig down
and up. This commit takes care of beaconining only which may be
sufficient for open mode connection, but not for WPA2 cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for an Action frame TX operation to be stopped in a way
that results in the TX status callback function not being called. This
could happen, e.g., when P2P_STOP_FIND was issued while waiting for PD
Response TX status. This specific case ended in leaving
p2p->send_action_in_progress set to 1 and that ending up stopping a
future TX operation when p2p_send_action_cb() gets called with
p2p->pending_action_state == P2P_NO_PENDING_ACTION.
This could result in reception of a fragmented service discovery
response failing due to the GAS sequence getting stopped when receiving
TX callback for the first GAS comeback request. That sequence could be
hit in mac80211_hwsim tests when p2p_listen_and_offchannel_tx was
followed by p2p_service_discovery_fragmentation (even after a long time
since this was on dev1 and there could be even 10 minutes between these
test cases).
Fix this issue by clearing send_action_in_progress whenever stopping
pending P2P operation with p2p_stop_find (or P2P_FLUSH for that matter).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When DFS offloading capability is supported by the driver, the driver
should use this event to indicate when channel availability check (CAC)
is started on a DFS channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds testing code (for CONFIG_TESTING_OPTIONS=y builds only) to
send an nl80211 vendor command and report a test vendor event in case
the driver supports this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not reply to a Probe Request frame with a DSSS Parameter Set element
in which the channel is different than the operating channel of the AP,
as the sending station is not found on the AP's operating channel.
IEEE Std 802.11-2012 describes this as a requirement for an AP with
dot11RadioMeasurementActivated set to true, but strictly speaking does
not allow such ignoring of Probe Request frames if
dot11RadioMeasurementActivated is false. Anyway, this can help reduce
number of unnecessary Probe Response frames for cases where the STA is
less likely to see them (Probe Request frame sent on a neighboring, but
partially overlapping, channel).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Send MESH-SAE-AUTH-BLOCKED event if SAE authentication is blocked. The
BLOCK state will finish when a new peer notification event is sent for
the same MAC address.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
SAE authentication fails likely with wrong password. This commit adds a
notification of the failure to the upper application (UI) so that the
application can notify suspection of a wrong password to the user. The
control interface monitor even for this is "MESH-SAE-AUTH-FAILURE
addr=<peer>".
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Commit 5a2a6de6a5 ('mesh: Make inactivity
timer configurable') has a problem on 32 bit systems. Setting
NL80211_MESHCONF_PLINK_TIMEOUT to 0xffffffff causes expiration of STA in
a minute by NL80211_CMD_DEL_STATION event. this is the kernel rule for
STA expiration:
(current jiffies) > (frame Rx jiffies + NL80211_MESHCONF_PLINK_TIMEOUT * 250)
On a 32 bit system, the right side could overflow and be unexpected
small value if NL80211_MESHCONF_PLINK_TIMEOUT is sufficiently large. STA
expiration occurs by this reason.
This patch solves the problem by disabling the STA expiration
functionality in mac80211. However, old kernel does not support
disabling it. If so, this patch sets mac80211 inactivity timer 60
seconds into future from the wpa_supplicant inactivity timer.
And I mis-understood that mesh_max_inactivity=0 disables inactivity
timer in wpa_supplicant. This commit fixes it also.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
