OSEN STAs are not authenticated, so do not send the actual BIGTK for
them so that they cannot generate forged protected Beacon frames. This
means that OSEN STAs cannot enable beacon protection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not include the actual GTK/IGTK value in FT protocol cases in OSEN or
with DGAF disabled (Hotspot 2.0). This was already the case for the
EAPOL-Key cases of providing GTK/IGTK, but the FT protocol case was
missed. OSEN cannot really use FT, so that part is not impacted, but it
would be possible to enable FT in a Hotspot 2.0 network that has DGAF
disabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not include the actual GTK/IGTK value in WNM Sleep Mode Response
frame if WNM Sleep Mode is used in OSEN or in a network where use of GTK
is disabled. This was already the case for the EAPOL-Key cases of
providing GTK/IGTK, but the WNM Sleep Mode exit case was missed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When a single hostapd process manages both the OWE and open BSS for
transition mode, owe_transition_ifname can be used to clone the
transition mode information (i.e., BSSID/SSID) automatically. When both
BSSs use ACS, the completion of ACS on the 1st BSS sets state to
HAPD_IFACE_ENABLED and the OWE transition mode information is updated
for all the other BSSs. However, the 2nd BSS is still in the ACS phase
and the beacon update messes up the state for AP startup and prevents
proper ACS competion.
If 2nd BSS is not yet enabled (e.g., in ACS), skip beacon update and
defer OWE transition information cloning until the BSS is enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Now that there is a pending mac80211 patch ("mac80211: allow SA-QUERY
processing in userspace") to allow wpa_supplicant to take care of SA
Query Request processing, start enforcing correct behavior for this in
ocv_sa_query and wpa2_ocv_sta_override_sa_query_resp.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED
to get the response for the queried data.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that all associated STAs that claim support for OCV initiate an
SA Query after CSA. If no SA Query is seen within 15 seconds,
deauthenticate the STA.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the OCV-FAILURE control interface event to notify upper layers of
OCV validation issues in FT and FILS (Re)Association Request frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the OCV-FAILURE control interface event to notify upper layers of
OCV validation issues in EAPOL-Key msg 2/4 and group 2/2.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new OCV-FAILURE control interface event to notify upper layers of
OCV validation issues. This commit adds this for SA Query processing in
AP mode.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make reporting of OCV validation failure reasons more flexible by
removing the fixed prefix from ocv_verify_tx_params() output in
ocv_errorstr so that the caller can use whatever prefix or encapsulation
that is most appropriate for each case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
To support the STA testbed role, the STA has to use specified channel
information in OCI element sent to the AP in EAPOL-Key msg 2/4, SA Query
Request, and SA Query Response frames. Add override parameters to use
the specified channel while populating OCI element in all these frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It was possible for the RSN state machine to maintain old PMKSA cache
selection (sm->cur_pmksa) when roaming to another BSS based on
driver-based roaming indication. This could result in mismatching state
and unexpected behavior, e.g., with not generating a Suite B PMKSA cache
entry.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that RSNE, MDE, and FTE have valid information in FT
Reassociation Response frames. In addition, decrypt GTK, IGTK, and BIGTK
from the frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is expected for the STA entry on the target AP to move directly from
State 1 to State 3 when performing FT over-the-DS (i.e., FT Action
Request/Response frame exchange through the old AP followed by
Reassociation Request/Response frame exchange with the target AP).
Signed-off-by: Jouni Malinen <j@w1.fi>
Define QCA vendor attributes for SET(GET)_WIFI_CONFIGURATION to
dynamically configure capabilities for TX A-MSDU and RX A-MSDU.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Add a QCA vendor subcommand QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC
to add and delete TSPEC in STA mode.
The attributes defined in enum qca_wlan_vendor_attr_config_tspec
are used to encapsulate required information.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Add new QCA vendor attributes to configure misbehavior for PMF
protection for Management frames and to inject Disassociation frames.
These attributes are used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute that can be used with
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION vendor command to
configure different PHY modes to the driver/firmware.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wpa_supplicant registered to process the Radio Measurement Request
frames unconditionally. This would prevent other location based
applications from handling these frames. Enable such a use case by
allowing wpa_supplicant to be configured not to register to process
these frames. This can now be done by adding "no_rrm=1" to the
driver_param configuration parameter.
In addition, wpa_driver_nl80211_init() does not have the provision to
take driver_params. Hence, resubscribe again with cfg80211 when this
driver parameter "no_rrm=1" is set after the initial setup steps.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process HE 6 GHz band capabilities in (Re)Association Request frames and
pass the information to the driver.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Construct HE 6 GHz Band Capabilities element (IEEE 802.11ax/D6.0,
9.4.2.261) from HT and VHT capabilities and add it to Beacon, Probe
Response, and (Re)Association Response frames when operating on the 6
GHz band.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
The VHT Operation Information subfield is conditonally present, so do
not hardcoded it in struct ieee80211_he_operation. These members of the
struct are not currently used, so these can be removed without impact to
functionality.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Defines IEEE P802.11ax/D6.0, 9.4.2.261 HE 6 GHz Band Capabilities
element and 6 GHz Operation Information field of HE Operation element
(IEEE P802.11ax/D6.0, Figure 9-787k).
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Some distros (e.g., Debian and Arch) already build wpa_supplicant with
support for TDLS, and Fedora is about to enable this feature as well.
Set CONFIG_TDLS=y in wpa_supplicant default build configuration.
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
If the current country code cannot be fetched, do not try to report the
current value in the log since that will result in TypeError exception.
Signed-off-by: Jouni Malinen <j@w1.fi>
Couple of VHT test cases missed explicit setting of hapd to None before
trying to start hostapd. Add those to avoid unexpected exceptions in
case hostapd start fails.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a decorator that clears ignore_old_scan_res parameter value instead
of doing this with try/finally in large number of test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a decorator that disables IPv6 and requires running
under a VM, rather than open-coding that many times.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The freqlist parameter uses comma, not space, separated values. Add
another test case for checking freqlist values that do not use the
preferred channel numbers to make sure the frequency list is actually
used as a constraint for selecting the channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a test for delayed group rekey retransmission that checks that
the IGTK is protected against it by not resetting the IPN replay
counter when reinstalling such a key.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While adding support for IGTK and BIGTK here, I tested this without
protections (i.e., with protections removed from both wpa_supplicant and
the driver), and while I got some bad resets on the debugfs values, it
should have failed with "unexpected connectivity".
Fix this to be correct - we need to reset the GTK PN, not the PTK PN in
this test.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use a shared wpa_alg_bip() function for this and fix the case in
nl_add_key() to cover all BIP algorithms. That fix does not change any
behavior since the function is not currently used with any BIP
algorithm, but it is better to avoid surprises should it ever be needed
with IGTK.
Signed-off-by: Jouni Malinen <j@w1.fi>
