This new mechanism can be used to combine multiple periodic AP
(including P2P GO) task into a single eloop timeout to minimize number
of wakeups for the process. hostapd gets its own periodic caller and
wpa_supplicant uses the previously added timer to trigger these calls.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, one timeout per process (by default every 30 seconds) was
used P2P peer expiration and another per-interface timeout (every 10
seconds) was used to expire BSS entries. Merge these to a single
per-process timeout that triggers every 10 seconds to minimize number of
process wakeups due to periodic operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The caller is not expected to free or modify the value since this is
returning a reference to a buffer maintained by the upper layer.
Signed-off-by: Jouni Malinen <j@w1.fi>
In case of a network interface removal, check if the interface
was also the parent interface of the P2P Device dedicated interface.
If this is the case, then stop the P2P Device functionality, and
remove the P2P Device dedicated interface.
In case that the interface is added again and P2P Device
functionality can be enabled again, add a new P2P Device dedicated
interface and allow further P2P Device functionality.
In case that the P2P Device dedicated interface is re-created, the
original P2P Device configuration file is needed, so store it in
the global params (instead in the wpa_interface configuration).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
1. Add global p2p_cli_probe property to enable/disable Probe Request
frame RX reporting for connected P2P Clients. The property can be set to
0 - disable or 1 - enable. The default value is 0.
2. Enable Probe Request frame RX reporting for P2P Client on
WPA_COMPLETED state if p2p_cli_probe property is set to 1. Disable it
when an interface state is changing to any other state.
3. Don't cancel Probe Request frame RX reporting on wpa_stop_listen for
a connected P2P Client handling Probe Request frames.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Remove all gas-query radio works before calling gas_query_deinit()
as gas_query_deinit() flow frees the query context, which might
be later be accessed from the radio work callback (and result
with unexpected behavior, e.g., segmentation fault).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This fixes some issues where a disconnection event may get ignored if an
earlier operation to remove or disable a network resulted in an attempt
to disconnect event though no connection was in place.
wpa_s->current_ssid != NULL alone is not sufficient to determine that
there will be a driver event notifying completion of such disconnection
request. Set own_disconnect_req to 1 only if wpa_s->wpa_state is also
indicating that there is a connection or an attempt to complete one.
This showed up in a failure, e.g., when running the hwsim test case
scan_int followed by ap_vlan_wpa2_psk_radius_required where the latter
ended up not processing a connection failure event and getting stuck not
trying to run a new scan and connection attempt.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Support a request to scan specific SSIDs given by user with the SCAN
command. The SSID list can be suffixed to the scan command as follows.
For example, if SSIDs "ABC" and "abc123" need to be specifically
scanned, the command should be "SCAN ssid 414243 ssid 616263313233". The
value of the SSID is passed in hexadecimal representation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In the case of driver-based BSS selection, a bssid_hint in the connect
request might not result in to the selection of the same BSS. Thus,
postpone the updation of the wpa_s->current_bss till the association
event is received unless the BSSID is forced. This fixes issues where
wpa_s->current_bss may end up being updated to point to the BSS that
wpa_supplicant provided as a hint for a roaming case, but then not
restored if the driver decides to "return" to the current BSS instead.
This could result in some operations (e.g., WNM BSS TM response) not
working properly due to incorrect BSS being identified in
wpa_s->current_bss.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 5add410162 ('WPS: Use shorter
authentication timeout during no-SelReg iteration') broke the build with
WPS disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 5add410162 ('WPS: Use shorter
authentication timeout during no-SelReg iteration') added a new
condition on reducing the authentication timeout for the WPS AP
iteration process. However, due it ended up copy-pasting an incorrect
condition for this. This was supposed to apply for PIN-based config
method advertisement, not PBC.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
When iterating through WPS APs that do not advertise Selected Registrar
TRUE, limit the authentication timeout to 10 seconds instead of the full
70 second value used with IEEE 802.1X/EAP/WPS in general. This helps
speed up AP iteration for cases where a selected AP misbehaves and does
not reply to EAP exchanges. This should not really be needed, but there
seems to be deployed APs that do not implement WPS correctly and with
such APs in the radio range, this extra timeout can speed up the
iteration to allow the correct AP to be found before the WPS operation
times out.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not add the dedicated P2P Device interface in case P2P is disabled in
the configuration file or globally.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This makes source code more consistent. The use within Android driver
interface is left as-is to avoid changes in the old PNO interface
definition.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It has been noticed that the band steering/load balancing of some
multi-AP networks will lead to an ever-growing list of blacklisted
BSSIDs. This eventually leads to a connection drop when the connection
is pushed to a distant AP.
Fix this issue by clearing the blacklist upon successful connect.
Signed-off-by: Jason Abele <jason@aether.com>
The new network profile parameter mem_only_psk=1 can be used to specify
that the PSK/passphrase for that network is requested over the control
interface (ctrl_iface or D-Bus) similarly to the EAP network parameter
requests. The PSK/passphrase can then be configured temporarily in a way
that prevents it from getting stored to the configuration file.
For example:
Event:
CTRL-REQ-PSK_PASSPHRASE-0:PSK or passphrase needed for SSID test-wpa2-psk
Response:
CTRL-RSP-PSK_PASSPHRASE-0:"qwertyuiop"
Note: The response value uses the same encoding as the psk network
profile parameter, i.e., passphrase is within double quotation marks.
Signed-off-by: Jouni Malinen <j@w1.fi>
If all networks are temporarily disabled, delay AP selection until at
least one network is enabled. Running AP selection when all networks are
disabled is useless as wpa_supplicant will not try to connect. In
addition, it will result in needless scan iterations that may delay the
connection when it is needed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When disconnecting from a BSS, the next scan is optimized to scan only
the channels used by the connected ESS. But when disconnecting because a
new network was selected, this optimization is wrong because
wpa_supplicant is now trying to connect to another ESS. Fix this by not
optimizing the scan frequencies in case the selected network has
changed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Static analyzers may warn about dereference before NULL check in
wpas_network_disabled() due to the new code added to check
wpa_s->p2p_mgmt. wpa_s cannot be NULL here, so remove the unneeded check
for it later in the function. (CID 106124)
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_supplicant_deinit_iface() ends up removing all P2P groups if the
removed interface is the parent interface. This is correct behavior in
general, but this resulted in issues in the new group interface
initialization error path since wpa_s->parent was not assigned before
hitting this check. Fix this by assigning wpa_s->parent as part of
wpa_supplicant_add_iface().
Signed-off-by: Jouni Malinen <j@w1.fi>
There are number of cases where wpa_supplicant requests the current
connection to be disconnected before starting a new operation. Such
cases do not really indicate that there was an error in connecting or a
disconnection initiated by the AP, so do not add a temporary blacklist
entry in such sequences.
Signed-off-by: Jouni Malinen <j@w1.fi>
The dedicated P2P management instance (wpas->p2p_mgmt == 1) using
cfg80211 P2P Device cannot be used for non-P2P uses or connection (there
is no netdev). Reject or ignore such operations to avoid unexpected
operations if enabled network blocks are configured in the
wpa_supplicant instance used to control this interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 563ee1832b ('IBSS: Add support for
VHT80 configuration') got merged in incorrectly with one i/j swap
missed.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This modifies the BSS selection routines to calculate SNR and estimated
throughput for each scan result and then use the estimated throughput as
a criteria for sorting the results. This extends the earlier design by
taking into account higher throughput rates if both the AP and local
device supports HT20, HT40, or VHT80. In addition, the maximum rate is
restricted based on SNR.
In practice, this gives significantly higher probability of selecting
HT/VHT APs when there are multiple BSSes in the same ESS and SNR is not
low enough to prevent higher MCS use.
Signed-off-by: Jouni Malinen <j@w1.fi>
If a matching IBSS is found in scan results, change requested frequency
to match and disable OBSS scan.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Add fixed_freq=<0/1> network block parameter and pass it to the driver
when starting or joining an IBSS. If this flag is set, IBSS should not
try to look for other IBSS networks to merge with on different channels.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
We should not enable HT if WEP or TKIP is configured.
Without the patch and WEP configuration we will get message:
Association request to the driver failed
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Linux kernel commit 576eb62598f10c8c7fd75703fe89010cdcfff596 ('bridge:
respect RFC2863 operational state') from 2012 introduced a regression
for using wpa_supplicant with EAPOL frames and a station interface in a
bridge. Since it does not look like this regression is going to get
fixed any time soon (it is already two years from that commit and over
1.5 from a discussion pointing out the regression), add a workaround in
wpa_supplicant to avoid this issue.
The wpa_supplicant workaround uses a secondary packet socket to capture
all frames (ETH_P_ALL) from the netdev that is in a bridge. This is
needed to avoid the kernel regression. However, this comes at the price
of more CPU load. Some of this is avoided with use of Linux socket
filter, but still, this is less efficient than a packet socket bound to
the specific EAPOL ethertype. The workaround gets disabled
automatically, if the main packet socket interface on the bridge
interface turns out to be working for RX (e.g., due to an old kernel
version being used or a new kernel version having a fix for the
regression). In addition, this workaround is only taken into use for the
special case of running wpa_supplicant with an interface in a bridge.
Signed-off-by: Jouni Malinen <j@w1.fi>
Drop the unneeded 'attempt' argument. This was originally used for
indicating an aborted PMKID caching attempt, but a fix in 2006 removed
the only such user and since that time, only attempt == 1 has been used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Connection with a PMF enabled AP will fail if we try to negotiate PMF
while the local driver does not support this. Since pmf=1 does not
require PMF for a successful connection, it can be ignored in such a
case to avoid connectivity issues with invalid configuration. This makes
it somewhat easier to allow upper layer programs to use pmf=1 default
regardless of driver capabilities.
Signed-off-by: Jouni Malinen <j@w1.fi>
external_scan_running should be common to all interfaces that share a
radio. This fixes a case where external_scan_running was set on a single
interface, but did not block scan on other interfaces.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Clear the reattach flags, in case a connection request did not trigger a
scan. This needs to be done to avoid leaving the reattach flag set for
the next scan operation which may not have anything to do with the
specific request that could have been optimized using the single-channel
single-SSID scan.
Signed-off-by: Ben <ben.rosenfeld@intel.com>
The new VENDOR_ELEM value 13 can now be used to add a vendor element
into all (Re)Association Request frames, not just for P2P use cases like
the previous item was for.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
At least MinGW did not have ENOTCONN, EOPNOTSUPP, ECANCELED, so define
these to allow the build to go through.
wpas_rrm_send_neighbor_rep_request() is not really used on Windows, so
the exact error code values do not make any difference here.
Signed-off-by: Jouni Malinen <j@w1.fi>
Automatically enable HT20, HT40+, HT40-, or VHT, based on driver
capabilities. This obsoletes the mesh_ht_mode network block parameter
that was previously used to configure HT parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add WPA_DRIVER_FLAGS_HT_IBSS driver feature flag. Some drivers could not
set this feature and next could fail when we will enable HT support for
IBSS with error message: nl80211: Join IBSS failed: ret=-22 (Invalid
argument).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
1. Supported MAC address randomization for scan.
2. Supported MAC address randomization for scheduled scan.
2. Supported MAC address randomization for pno.
4. Add functions to set and clear the MAC address randomization
state variables.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The specification requires the tspecs to be kept upon reassociation to
the same BSS. Save the last tspecs before such reassociation, and
reconfigure on the association notification.
Note that the current flow is not transparent to the user
(it is notified about deauth/reassoc and tspec removal/addition).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
In case of roaming, we don't get disassoc notification, but
still want to remove the existing tspecs.
Move the wmm_ac_notify_disassoc() call to the state change
function, which get called also on roaming.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
There is no need to leave this temporary key in stack memory after
having been configured to the WPA state machine.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_ft_sae test case managed to hit a somewhat unclear error case which
resulted in "WPA: Failed to select WPA/RSN" print and not enough
information to figure out what exactly had went wrong.
Signed-off-by: Jouni Malinen <j@w1.fi>
Android framework maintains a state to process the scan results after
the scan is issued. If wpa_supplicant issues the scan during the
initialization, the one issued by the framework may fail (with EBUSY) if
the host driver is already processing the scan. Thus, the scan results
returned for the first scan triggered by wpa_supplicant are not
processed for getting displayed resulting in delay for the display of
the first scan results after the Wi-Fi subsystem initialization. Thus,
trigger the scan only based on the framework request on Android.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.
This command makes a virtual mesh interface to be used for mesh gate.
This command expects to be used like this.
wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The send_eapol() callback was used by driver_test.c, but with that
removed, there is no remaining users of the alternative EAPOL frame
transmitting mechanism in wpa_supplicant, i.e., all remaining driver
interfaces use l2_packet instead. Remove the send_eapol() to get rid of
unused code.
Signed-off-by: Jouni Malinen <j@w1.fi>
Externally triggered scan could result in a new radio work item getting
started even when external radio work was in progress. Delay such start
until the external work is completed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The mesh group addition was designed to use wpa_s->connect_without_scan
to skip a scan. That path was skipped if wpa_supplicant_fast_associate()
allowed previous scan results to be used. This could result in undesired
double-initialization attempt for the mesh interface. Avoid this by not
using wpa_supplicant_fast_associate() when wpa_s->connect_without_scan
is set.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for wmm_ac_deinit() not getting called when an interface
was removed in a sequence where disassociation was not reported and
wmm_ac_notify_disassoc() did not get called. This resulted in leaking
whatever memory was allocated for WMM AC parameters. Fix that by calling
wmm_ac_notify_disassoc() from wpa_supplicant_cleanup().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to fix some sequencies where a real scan in ap_scan=2
case would be issued even when the connection case would expect direct
connection without a scan.
This fixed an issue shown in hwsim test case autoscan_exponential
followed by ibss_open_fixed_bssid.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Allow supplying an SSID for the SSID IE. If not supplied, no SSID IE is
sent, and the request implies the current SSID.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Add the ability to send a Neighbor Report Request (part of
RRM). Requester is then notified once the report arrives.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
When the list of preferred transition candidates is received, use the
identified channels to optimize the following scan so that no time is
wasted on other channels.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add add_tx_ts() and del_tx_ts() ops to notify the driver about
TSPEC add / delete.
Additionally, add wmm_ac_supported flag to indicate
whether the driver supports WMM AC.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Parse MESH_GROUP_ADD/REMOVE commands on ctrl interface and call
wpa_supplicant routines. These commands are used to start or
join and leave a mesh network.
The mesh id is given in the configuration file, therefore there is
no need to scan before joining a mesh network. We reuse the
connect_without_scan construct used by P2P for that same purpose.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
New kernels in wiphy_suspend() will call cfg80211_leave_all() that will
eventually end up in cfg80211_stop_ap() unless wowlan_triggers were set.
For now, use the parameters from the station mode as-is. It may be
desirable to extend (or constraint) this in the future for specific AP
mode needs.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for scan result processing or BSS entry removal to occur
while there is a pending connect or sme-connect radio work with a
previously selected BSS entry. The BSS pointer was previously verified
to be valid, i.e., still point to a BSS entry, at the time the actual
connection operation is started. However, that BSS entry could have
changed to point to another BSS if the old BSS entry was either removed
or reallocated and a new BSS entry was added at the same location in
memory. This could result in the connection attempt failing to configure
parameters properly due to different BSS information (e.g., different
BSSID).
Fix this by updated the pending connect radio work data on BSS entry
updates similarly to how the last_scan_res array was updated. If the
selected BSS entry is removed, this will still result in a failed
connection, but reallocated BSS entry is now followed properly and used
when the connection work starts.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit fixes couple of connection failure paths where
wpas_connect_work_done() was not called, thus enabling the radio work
interface to proceed with the other queued actions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 22628eca34 ('Support driver-based
BSS selection in ap_scan=1 mode') ended up disabling the special
ap_scan=2 WPS case where ap_scan=1 like scan followed by association is
used to find the WPS AP using wildcard SSID. Fix this by allowing
association request even with wpas_driver_bss_selection() when searching
for a WPS AP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DBus client should always request the proper netdev interface. This will
be necessary to get a consistent behavior whatever driver is in use:
iwlwifi (which requires a P2P mgmt dev), ath9/10k (which does not),
etc...
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add smps_modes field, and let the driver fill it with its supported SMPS
modes (static/dynamic). This will let us start an AP with specific SMPS
mode (e.g., dynamic) that will allow it to reduce its power usage.
Signed-off-by: Eliad Peller <eliad@wizery.com>
This commit introduces a QCA vendor command and event to provide an
option to use extended versions of the nl80211 connect/roam operations
in a way that allows drivers to offload key management operations to the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This moves the addition of P2P Device interface into
wpa_supplicant_add_iface() so that this operation can be done
dynamically when adding an interface to an already running
wpa_supplicant process.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed to allow dynamic removal of an interface that adds the
P2P Device interface without leaving behind the management interface
with invalid wpa_s->parent pointer.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is now possible to run hwsim_test like data connectivity test through
wpa_supplicant/hostapd control interface if CONFIG_TESTING_OPTIONS=y is
used for the build. Test functionality is enabled/disabled at runtime
with "DATA_TEST_CONFIG <1/0>". The "DATA_TEST_TX <dst> <src> <tos>"
command can be used to request a test frame to be transmitted.
"DATA-TEST-RX <dst> <src>" event is generated when the test frame is
received.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes wpa_supplicant SME create PMKSA cache entries from SAE
authentication and try to use PMKSA caching if an entry is found for the
AP. If the AP rejects the attempt, fall back to SAE authentication is
used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Increase EAPOL startWhen to 2 for the case where the AP/GO has
advertised it supports WPS 2.0. This is done to make it less likely for
the EAPOL-Start frame to be sent out since that is only required for WPS
1.0. Not sending it can remove one unnecessary round trip from the EAP
exchange when the AP is going to start with EAP-Request/Identity
immediately based on the Association Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The MACsec addition placed one of the calls outside the #ifdef
IEEE802X_EAPOL block while the variable needed for this was defined only
within the block.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new openssl_cipher configuration parameter can be used to select
which TLS cipher suites are enabled for TLS-based EAP methods when
OpenSSL is used as the TLS library. This parameter can be used both as a
global parameter to set the default for all network blocks and as a
network block parameter to override the default for each network
profile.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, wpas_set_wowlan_triggers() could have been called in
uninitialized wpa_driver_capa data if the driver interface did not
support reporting of capabilities. While this would not really happen
with a driver wrapper that implements set_wowlan() and as such, would
not cause any difference in practice, it is better to clean this up to
make the code path easier to understand for static analyzers.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for local deauthentication request to leave sme-connect
radio work running even when there was no ongoing effort to complete the
connection anymore. Clean this up by marking sme-connect radio work
item, if any, done when clearing connection state after such
disconnection during connection.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use hostapd_freq_params instead of simple frequency parameter for driver
commands. This is preparation for IBSS configuration to allow use of
HT/VHT in IBSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Previously, the case of non-netdev P2P management device ended up
pulling in both the main interface (e.g., wlan0) and P2P Device
interface (from command line -m argument) as configuration. Similarly,
the main interface ended up included both configuration files. This is
not really helpful for various use cases, e.g., when permanent P2P group
information is stored in the P2P Devince interface, but it gets
duplicated in the main station interface configuration.
Clean this up by changing the -m<file> argument to replace, not
concatenate, configuration information. In other words, the main station
interface will not read this configuration and the P2P Device interface
(non-netdev) does not read parameters from the station interface
configuration file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
mac_addr=2 and preassoc_mac_addr=2 parameters can now be used to
configure random MAC address to be generated by maintaining the OUI part
of the permanent MAC address (but with locally administered bit set to
1). Other than that, these values result in similar behavior with
mac_addr=1 and preassoc_mac_addr=1, respectively.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.
This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.
This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.
The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the shorter startWhen value was used based on build
parameters (i.e., if WPS was enabled). This is not really ideal and the
knowledge of WPS use can be provided to the EAPOL state machine to allow
this (and similar WPS workarounds) to be done only when the association
is for the purpose of WPS.
Reduce the default startWhen value from 3 to 2 seconds for non-WPS case
since WPS builds have likely received most testing for the past years
with the 1 second value and there is no strong justification for forcing
the longer 3 second wait should a frame be lost or something else
require the EAPOL-Start to initiate operation after a connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds following new control interface commands to allow arbitrary
vendor elements to be added into number of frames:
VENDOR_ELEM_ADD <frame id> <hexdump of elem(s)>
VENDOR_ELEM_GET <frame id>
VENDOR_ELEM_REMOVE <frame id> <hexdump of elem(s)>
VENDOR_ELEM_REMOVE <frame id> *
The following frames are supported in this commit (additional frames can
be added in the future):
0 = Probe Request frame in P2P device discovery
1 = Probe Response frame from P2P Device role
2 = Probe Response frame from P2P GO
3 = Beacon frame from P2P GO
4 = PD Req
5 = PD Resp
6 = GO Neg Req
7 = GO Neg Resp
8 = GO Neg Conf
9 = Invitation Request
10 = Invitation Response
11 = P2P Association Request
12 = P2P Association Response
One or more vendor element can be added/removed with the commands. The
hexdump of the element(s) needs to contain the full element (id, len,
payload) and the buffer needs to pass IE parsing requirements to be
accepted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use an explicit memset call to clear any wpa_supplicant configuration
parameter that contains private information like keys or identity. This
brings in an additional layer of protection by reducing the length of
time this type of private data is kept in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
While the buffer is expected to be large enough for all the IEs, it is
better to check for this explicitly when adding the HS 2.0 Indication
element. (CID 68601)
Signed-off-by: Jouni Malinen <j@w1.fi>
This removes number of unnecessary #ifdef CONFIG_P2P blocks from generic
code by hiding the conditional build into p2p_supplicant.h with empty
inline functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
Performing a P2P Device flow such as p2p_listen or
p2p_find, can degrade the performance of an active interface
connection, if the listen frequency is different than the
frequency used by that interface.
To reduce the effect of P2P Device flows on other interfaces,
try changing the listen channel of the P2P Device to match the
operating channel of one of the other active interfaces. This change
will be possible only in case that the listen channel is not forced
externally, and will be delayed to a point where the P2P Device
state machine is idle.
The optimization can be configured in the configuration file and
is disabled by default.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Remove the seperation between getting the local interface frequency and
other interfaces frequencies since going over all the radio interfaces
includes the local interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When the number of frequencies supported by the kernel is bigger than
one, and there is a need to pick a frequency for a new flow such as P2P
GO Negotiation or P2P Invitation, the flow should be able to pick the
best frequency among all the frequencies currently used by the device.
In order to prioritize between the currently used frequencies, add
the ability to collect additional data about each used frequency
(if the frequency is used by a station interface or P2P Client)
and when needed select the best frequency, where:
1. Infrastructure interfaces have highest priority
2. P2P Client interfaces have higher priority over AP/GO
interfaces.
The rational is that the frequency of an AP/GO can change while
that of a station interface cannot.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Remove the check for get_radio_name support from
get_shared_radio_freqs_data() since get_radio_name is no longer in use
in this function.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The OSEN code path hardcodes number of struct wpa_ie_data items.
However, it did not clear the full structure and some uninitialized
fields could have been used (e.g., ie.mgmt_group_cipher for a debug
print and ie.capabilities for checking MFPC). Fix this by clearing the
ie data before filling in the hardcoded OSEN values.
Signed-off-by: Jouni Malinen <j@w1.fi>
Prepare for new extended capabilities bits by checking that the local
buffer is large enough to contain all the bits the driver requests. The
existing buffers are large enough to include anything defined until now,
but it would be possible to add more definitions in the future, so
increase them a bit as well to make this more future proof.
Signed-off-by: Jouni Malinen <j@w1.fi>
When there is a pending WPS negotiation for P2P and signal interrupt is
triggered, invalid read occurs in wpas_wps_terminate_pending() if
wpas_p2p_disconnect() removed the interface. Inverting deinit order
solves the issue.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
Add a new wowlan_triggers option to wpa_supplicant.conf. The triggers in
this key will be used to configure the kernel wowlan configuration.
For now, support only simple flags. More complex triggers can be added
later on.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Previously, the frequency conflict was handled only during the
association flow. However, some drivers, e.g., mac80211 based
drivers, will fail an authentication request in case that there
are no available channels for use (as they might be used by
other interfaces), and thus the frequency conflict resolution
is never called.
Fix this by calling frequency conflict resolution during
authentication (SME-in-wpa_supplicant) as well.
In addition, get the shared radio frequency from the wpa_s context in
both the SME-in-driver and SME-in-wpa_supplicant cases and not from the
driver.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The normal scan counter is used to trigger a few normal scans before a
scheduled scan is issued. The reason for doing this is that we get
results faster and some drivers support more SSIDs per normal scan
than during sched scan. After 2 normal scans, we start using
sched_scan. But the problem is that when a connection succeeds, we do
not reset this counter, so we will keep using sched scans.
To fix this, now we reset the counter when we switch to WPA_COMPLETED
state.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Previously, it was possible to remove the main interface and leave
behind dynamic P2P group interfaces. This would eventually result in
references freed memory, so it is not really suitable behavior. Instesd,
remove all the dynamic P2P group interfaces that were created through an
interface that is now removed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This used to work, but it looks like the disabled-PSK-network check
ended up rejecting confiurations that configured a wildcard SSID with a
passphrase (instead of PSK).
Signed-off-by: Jouni Malinen <j@w1.fi>
According to the standard, if the max A-MPDU VHT cap is <= 3, we
have to adjust the max A-MPDU HT cap to the same value. Otherwise
it should be set to 3.
Take care of it when the max VHT A-MPDU value is overridden.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
This allows hostapd to set a different management group cipher than the
previously hardcoded default BIP (AES-128-CMAC). The new configuration
file parameter group_mgmt_cipher can be set to BIP-GMAC-128,
BIP-GMAC-256, or BIP-CMAC-256 to select one of the ciphers defined in
IEEE Std 802.11ac-2013.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A previous patch "Support VHT capability overrides" missed one
place where HT overrides were being applied and where it would
also be useful to apply VHT overrides.
Signed-hostap: Paul Stewart <pstew@chromium.org>
This makes stations associate much faster when using lots of stations.
In addition, this avoids delaying the initial scan continuously for
dynamic interface removal/addition cases.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Add an option to specify a configuration file that can be used to hold
the P2P_DEVICE configuration parameters. If this option is not used, the
P2P_DEVICE configuration parameters will be read from interface
configuration file.
Note that it is advised to use this option in some cases such as:
If a P2P_DEVICE is supported by the driver, the wpa_supplicant creates a
dedicated P2P Device interface, where the configuration file used for
the main interface is used. As a consequence, if the configuration file
includes network definition etc., the wpa_supplicant will try to perform
station specific flows on the P2P Device interface which will fail.
If a P2P_DEVICE is supported by the driver and update_config is used,
the P2P Device configuration data will override the main interface
configuration data.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
wpa_supplicant already allowed beacon interval to be configured for AP
mode operations, but this was not passed to the driver for IBSS even
though the same parameter can used for that case. Add this for the
nl80211 driver interface to allow beacon interval to be controlled for
IBSS as well.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant started delayed sched scan also on P2P Device interfaces,
resulting in erroneous scans and connection attempts. Skip that on
driver init when the interface is dedicated only for P2P management
purposes.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
As a P2P group has a unique SSID and one security domain, it does
not make sense to enable background scanning for roaming purposes.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Do not initialize bgscan if the user explicitly set bgscan to an empty
string. Without this patch wpa_supplicant tries to initialize bgscan to
the first option if the string is empty.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
This is needed to limit the number of consecutive authentication
attempts to no more than 10 within a 10-minute interval to avoid
unnecessary load on the authentication server. In addition, use a random
component in the delay to avoid multiple stations hitting the same
timing in case of simultaneous disconnection from the network.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_cli fetch_osu command can be used to fetch information about
all OSU providers and write that to a text file with the icons in
separate files. cancel_osu_fetch command can be used to stop ongoing OSU
provider list fetch.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Subscription remediation notification WNM-Notification Request is now
shown in the following way in wpa_supplicant control interface:
<3>HS20-SUBSCRIPTION-REMEDIATION http://example.com/foo/
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The HS 2.0 Indication element from wpa_supplicant now includes the
release number field and wpa_supplicant shows the release number of the
AP in STATUS command (hs20=1 replaced with hs20=<release>).
The new update_identifier field in the cred block can now be used to
configure the PPS MO ID so that wpa_supplicant adds it to the Indication
element in Association Request frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the connect or sme-connect radio work to get
re-scheduled while an earlier request was still pending, e.g.,
select_network is issued at the moment a scan radio work is in progress
and the old scan results are recent enough for starting the connection.
This could result in unexpected attempt to re-associate immediately
after completing the first connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While testing rfkill blocking of a scanning interface, it
was seen that the ongoing scan never completes. This happens
since EVENT_SCAN_RESULTS is discarded on a disabled interface.
Fix this and also other possible radio work completion issues
by removing all the radio works (including started) of the
disabled interface.
To be able to remove already started radio works, make their
callbacks be reentrant with deinit flag (when the work
is started), so each radio work should be able to handle
its own termination.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This uses the new nl80211 attributes to allow the connect command to
provide bssid and freq hints to the driver without limiting roaming to
the specific BSS/frequency. This can be used by drivers that perform
internal BSS selection (WPA_DRIVER_FLAGS_BSS_SELECTION) as a candidate
for initial association.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
1. In wpa_config_process_bgscan() fix memory leak after
calling wpa_config_parse_string()
2. In hostapd_config_defaults(), on failure to allocate bss->radius,
conf->bss was not freed.
3. In p2p_deauth_nofif(), memory allocated in p2p_parse_ies() was not
freed in case of NULL minor_reason_code.
4. In p2p_disassoc_nofif(), memory allocated in p2p_parse_ies() was
not freed in case of NULL minor_reason_code.
5. In p2p_process_go_neg_conf(), memory allocated was not freed in
case that the P2P Device interface was not waiting for a
GO Negotiation Confirm.
6. In wpa_set_pkcs11_engine_and_module_path(), the wrong pointer was
checked.
Signed-hostap: Eytan Lifshitz <eytan.lifshitz@intel.com>
This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.
The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:
ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100
DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a QCA vendor specific nl80211 event to allow the driver to
indicate a list of frequency ranges that should be avoided due to
interference or possible known co-existance constraints. Such
frequencies are marked as not allowed for P2P use to force groups to be
formed on different channels.
If a P2P GO is operating on a channel that the driver recommended not to
use, a notification about this is sent on the control interface and
upper layer code may decide to tear down the group and optionally
restart it on another channel. As a TODO item, this could also be changed
to use CSA to avoid removing the group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This patch resets the static interface_count to zero in case of
wpa_supplicant_driver_init() call for wpa_s which is in
INTERFACE_DISABLED state. This interface_count is used for the delay of
the scan which is now minimal for dynamically added interfaces. This may
collide with a scan for another interface, but the same is true for any
chosen delay in this scenario. Also the state change to DISCONNECTED is
moved to wpa_supplicant_driver_init() so it will move from
INTERFACE_DISABLED to INACTIVE when there are no enabled networks.
Tested-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Depending on the implementation, the scheduled scan may not give results
quickly when in DISCONNECTED state. This patch resets
wpa_s::normal_scans upon entering to the INTERFACE_DISABLED state so a
normal scan is assured upon going to DISCONNECTED state after the
interface has been re-enabled. This mainly solves a long reconnect time
observed upon repeated kernel driver reloads, i.e., third reload
resulted in a scheduled scan.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-hostap: Arend van Spriel <arend@broadcom.com>
Some EAP methods can go through a step that is expected to fail and as
such, should not trigger temporary network disabling when processing
EAP-Failure or deauthentication. EAP-WSC for WPS was already handled as
a special case, but similar behavior is needed for EAP-FAST with
unauthenticated provisioning.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, only the last response data was kept in memory. This
increases that to hold up to two last responses to allow some more
parallel operations to be requested. In addition, the response data is
now freed as soon as the external program has fetched it.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new control interface command RADIO_WORK can be used by external
programs to request radio allocation slots from wpa_supplicant if
exclusive radio control is needed, e.g., for offchannel operations. If
such operations are done directly to the driver, wpa_supplicant may not
have enough information to avoid conflicting operations. This new
command can be used to provide enough information and radio scheduling
to avoid issues with such cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
If an external program triggers a scan, wpa_supplicant does not have a
wpa_radio work item for this operation to protect against other
offchannel operations. This can result in operations failing, so try to
avoid damage by not starting any new wpa_radio work items during a scan
that was started by another process.
Signed-hostap: Jouni Malinen <j@w1.fi>
This type of protection against concurrent connection and scan
operations is now enforced through the wpa_radio work mechanism, so this
separate protection mechanism is not needed anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
Avoid concurrent P2P scan requests with any other exclusive use of the
radio by using the radio work queuing mechanism. This removes some of
the earlier workarounds that postponed scans depending on other
operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new radio work item concept can be used to request time for an
operation that requires exclusive radio control, e.g., a scan. Once the
radio is available, the registered callback function will be called.
radio_work_done() must be called once the exclusive radio operation has
been completed, so that the radio is freed for other operations. The
special case of deinit=1 is used to free the context data during
interface removal. That does not allow the callback function to start
the radio operation, i.e., it needs to free the allocated resources
and return.
Signed-hostap: Jouni Malinen <j@w1.fi>
Track set_key operations per-key index and clear keys on disconnection
only if the key was set (or may have been set which is the case for the
first operation after wpa_supplicant start).
Signed-hostap: Jouni Malinen <j@w1.fi>
These were somewhat more hidden to avoid direct use, but there are now
numerous places where these are needed and more justification to make
the extern int declarations available from wpa_debug.h. In addition,
this avoids some warnings from sparse.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPA_CIPHER_* and CIPHER_* are used for the exact same set of cipher
suites with the main difference being that the WPA_CIPHER_* version is
suitable to be used as a bitfield. Similarly, WPA_KEY_MGMT_* and
KEY_MGMT_* have similar design for AKMs. There is no need to maintain
two separate copies of the definitions since the bitfield compatible
version can be used for both needs. Get rid of the CIPHER_* and
KEY_MGMT_* versions to clean up the implementation by getting rid of
unnecessary mapping functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
The earlier changes to buffer EAPOL frames when not associated to avoid
race conditions (especially commit
3ab35a6603 but maybe something even before
that) broke PeerKey 4-way handshake. Fix this by using a separate check
before the race condition workaround to process PeerKey 4-way handshake
EAPOL-Key messages differently.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new freq=<frequency ranges> parameter to the SCAN command can be
used to request a scan to be performed on the specified set of channels
instead of on all channels. For example, "wpa_cli scan
freq=2400-2500,5180" would scan channels 1-14 and 36. Only the channels
that the driver indicates as enabled and that are within the specified
ranges are included in the request.
Signed-hostap: Jouni Malinen <j@w1.fi>
In wpa_supplicant_terminate_proc(), while iterating and
terminating interfaces, after an interface is terminated,
we can no longer access its memory as it is no longer valid
and causes a crash.
Fix this by saving the pointer to the next interface before freeing
the current one to avoid accessing an invalid memory location.
Signed-hostap: Moshe Benji <moshe.benji@intel.com>
Temporarily disabled networks are disabled for a certain
duration, so the code should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The EAPOL RX workaround checks that the events are less than 100 ms
apart, so only uses relative times and should use monotonic time.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Stopping bgscan on any state other than COMPLETED results
in bgscan reset (stop + start) on every rekeying operation.
Signed-hostap: Eliad Peller <eliad@wizery.com>
Do not assume the driver supports QoS Mapping, but instead, advertise
support for this only if CONFIG_INTERWORKING is defined and driver
indicates support for configuring QoS Map.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 202dec2a94 introduced a never
ending loop for a case where a single wpa_supplicant process is used
with multiple radios. Fix this by advancing the iface pointer properly
to the next interface in the loop until a NULL pointer is hit.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Based on priority, remove the connection with least priority whenever
a frequency conflict is detected.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
struct wpa_radio is used as a shared data structure between all struct
wpa_supplicant instances that share the same physical radio.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit eb32460029 left an unneeded
sim_type argument to scard_init(). Remove that unnecessary argument to
clean up the implementation.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
This prints out get_shared_radio_freqs() results and related information
from P2P operations to make debug logs more helpful for figuring out
issues related to multi-channel concurrency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The idx variable was mistakenly set to 0 at the beginning of the
interface iteration. This could result in the operating channel of the
interface calling the function from being removed from the returned
frequency array if other interfaces were operating.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
This option can be used to globally configure bgscan parameters
for all the network blocks.
Note that this configuration will not override a network block
specific bgscan settings, but will only be used in case that
the network block does not have a valid bgscan configuration.
Signed-hostap: Haim Dreyfuss <haim.dreyfuss@intel.com>
Both of these variables can result in optimized WPS scans, so better
clear these more consistently to avoid unexpected single-channel scans.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_s->conf cannot be NULL because wpa_supplicant_init_iface() would not
allow wpa_supplicant_add_iface() to return wpa_s instance in such state.
Signed-hostap: Jouni Malinen <j@w1.fi>
Trying to access the SIM card details without checking if the eap_proxy
layer has been initialized can results in a crash. Address this by
sending the request for the IMSI through eapol_supp_sm.c which can
verify that eap_proxy has been initialized.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
DISCONNECT followed by ENABLE_NETWORK ended up starting a scan for a new
connection due to wpa_supplicant_enable_one_network() setting
wpa_s->reassociate = 1. This was done regardless of wpa_s->disconnected
being 1 which should imply that wpa_supplicant should not try to connect
before asked explicitly with REASSOCIATE or RECONNECT.
Fix this by making ENABLE_NETWORK setting of reassociate = 1 and
starting of scans for connection conditional on wpa_s->disconnected ==
0. This will make ENABLE_NETWORK trigger a connection only if
wpa_supplicant is already in a state where it would try to connect if
there are any enabled networks.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Offchannel operations needed for a GAS query can conflict with ongoing
scan/connection progress, so delay GAS queries if such an operation is
in progress on the current interface or any virtual interface sharing
the same radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new configuration parameter external_sim=<0/1> can now be used to
configure wpa_supplicant to use external SIM/USIM processing (e.g., GSM
authentication for EAP-SIM or UMTS authentication for EAP-AKA). The
requests and responses for such operations are sent over the ctrl_iface
CTRL-REQ-SIM and CTRL-RSP-SIM commands similarly to the existing
password query mechanism.
Changes to the EAP methods to use this new mechanism will be added in
separate commits.
Signed-hostap: Jouni Malinen <j@w1.fi>
Indicate support for QoS Mapping and configure driver to update the QoS
Map if QoS Map Set elements is received from the AP either in
(Re)Association Response or QoS Map Configure frame.
This commit adds support for receiving the frames with nl80211 drivers,
but the actual QoS Map configuration command is still missing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add Extended Capabilities element to association request only if the AP
included this element in Beacon/Probe Response frames. This is a
workaround to address interoperability issues with some older APs that
do not seem to be able to handle Extended Capabilities element in
(Re)Association Request frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Killing the wpa_supplicant process or using TERMINATE ctrl_iface command
resulted in the process existing without cleaning up possibly added
dynamic P2P group interfaces. Clean this up by stopping each P2P group
before stopping eloop.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant crashes if driver configuration for AP mode interface
configuration fails after group negotiation. This is because of a
regression from commit 1075b29571 that
ends up freeing the wpa_s instance from within
wpa_supplicant_create_ap() without the caller knowing.
Fix this by using an eloop timeout to free remove the P2P group so that
wpa_supplicant_create_ap() and especially wpa_supplicant_associate()
callers do not need to know about interface getting possibly removed. In
addition, move the P2P specific code into p2p_supplicant.c where it
really belongs. This allows the already existing group formation timeout
to be used by reducing the timeout to zero.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
There were some code paths that allowed obsolete configuration data
pointer to be maintained within EAPOL supplicant in case a network was
removed while not connection to it (i.e., wpa_s->current_ssid not
pointing to the network that was removed). This could result in use of
freed memory, e.g., from eap_sm_notify_ctrl_attached() when a new
control interface connected prior to the EAPOL supplicant configuration
pointer got updated.
Signed-hostap: Jouni Malinen <j@w1.fi>
4-way handshake may fail under extremely noisy environment and if this
happens during P2P group formation, the 10 second extra delay added in
wpas_auth_failed() can result in running over the 15 second timeout.
Avoid this by skipping the delay mechanism in wpas_auth_failed() for the
P2P group formation case. The P2P formation timeout will take care of
stopping the attempts if the failure condition does not get resolved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some driver interfaces may not support the get_radio_name() design and
get_shared_radio_freqs() needs to be aware of such possibility when
determining shared radio frequencies.
Signed-hostap: Jouni Malinen <j@w1.fi>
There are devices that can operate several channels concurrently.
Change shared_vif_oper_freq() to get_shared_radio_freqs() that can
return an array of frequencies currently used by all the virtual
interfaces that share the same radio.
In addition, move it to wpa_supplicant.c, so it can be used by other
modules.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
Previously, drivers only reported if they support multiple concurrent
channels, but did not report the maximum number of supported channels.
Add this reporting to the driver capabilities and add the implementation
to driver_nl80211.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
Because a delayed scheduled scan will access the members of struct
wpa_supplicant which is freed and this can result in a crash,
wpa_supplicant needs to cancel delayed scheduled scan during cleanups.
Signed-hostap: Chengyi Zhao <chengyix.zhao@gmail.com>
Adding a new wpa_supplicant control interface for the dedicated
P2P_DEVICE would be quite confusing for programs that manage P2P
operations. Remove this control interface and require the global control
interface to be used since it will provide consistent interface for both
the new dedicated P2P_DEVICE (non-netdev) and old style P2P management
through a netdev.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit c68f6200a7 made these calls
conditional on !p2p_mgmt, but forced p2p_mgmt=1 for cases where the
driver does not use the dedicated P2P Device. Fix this by making the
!p2p_mgmt condition apply only if the driver does indicate use of a
dedicated P2P Device.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the capability flag of the driver indicates a dedicated P2P Device is
supported, a P2P Device interface is created.
Create the P2P Device in main interface creation loop when the added
interface flags support and P2P supplicant is not yet initialized
avoiding recursion of add_interface.
Do not register l2_packet for P2P Device interface (both for EAPOL and
for TDLS).
Signed-hostap: Arend van Spriel <arend@broadcom.com>
In wpa_supplicant_deinit(), the function wpas_p2p_deinit_global()
was called. Remove it as it will be called from wpas_deinit_iface()
upon removal of the P2P management interface.
Signed-hostap: Arend van Spriel <arend@broadcom.com>
This makes ENABLE_NETWORK behave similarily to SELECT_NETWORK by
allowing a scan to be skipped if recent scan results are available.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The optional -G<group> command line argument can be used to specify the
group that can access the global control interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
This cleans up debug log by not trying to process the disconnection
event as a failure that could result in blacklist addition and auto
connect attempt. These are pointless operations since the interface is
going to removed immediately after this.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no point in marking a BSS temporarily blacklisted based on a
connection failure or disconnection case if that happens as a result of
a local request to disconnect. The blacklist entry could result on
unexpected BSS getting selected on the next connection attempt. In
addition, the code to try to find another BSS within the ESS could
result in scanning a single channel on the next attempt. Fix these
issues by handling the connection failure events only if we are not in
disconnected state (i.e., would try to reconnect after this
automatically).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Scanning can delay concurrent operations considerably, so it is better
to avoid that while trying to connect on any of the virtual interfaces
that share the same radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
