Commit graph

10071 commits

Author SHA1 Message Date
Jouni Malinen
f6c09bf46e tests: Remove HwsimSkip from p2p_channel
With the optimizations from the previous commits, none of the test cases
here need to be skipped.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-27 19:38:17 +02:00
Jouni Malinen
858d12f69a tests: Optimize p2p_go_move_active initial wait
There is no need to wait for the initial client timeout in this type of
test sequence since that wait can be cleared by connecting and
disconnecting a client to the group. This allows the test case to be
executed much more quickly and the dependency on --long can be removed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-27 19:37:35 +02:00
Jouni Malinen
ae248721f4 tests: Optimize p2p_go_move_reg_change initial wait
There is no need to wait for the initial client timeout in this type of
test sequence since that wait can be cleared by connecting and
disconnecting a client to the group. This allows the test case to be
executed much more quickly and the dependency on --long can be removed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-27 19:35:51 +02:00
Jouni Malinen
63b87a5aeb tests: Optimize p2p_go_move_scm_multi initial wait
There is no need to wait for the initial client timeout in this type of
test sequence since that wait can be cleared by connecting and
disconnecting a client to the group. This allows the test case to be
executed much more quickly and the dependency on --long can be removed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-27 19:31:44 +02:00
Jouni Malinen
3acf68feb9 tests: Convert p2p_go_move_scm_multi to use dynamic hwsim
Use a dynamically added HWSimRadio to allow the MCC case to be covered
with a single test run with the mac80211_hwsim default radios disabling
MCC.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-27 19:30:02 +02:00
Jouni Malinen
d18df681b0 tests: Convert p2p_go_move_scm_peer_does_not_support to dynamic hwsim
Use a dynamically added HWSimRadio to allow the MCC case to be covered
with a single test run with the mac80211_hwsim default radios disabling
MCC.

In addition, remove dependency on --long since this test case does not
really take that long.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-27 19:27:25 +02:00
Jouni Malinen
f0b39e057a tests: Convert p2p_go_move_scm_peer_supports to use dynamic hwsim
Use a dynamically added HWSimRadio to allow the MCC case to be covered
with a single test run with the mac80211_hwsim default radios disabling
MCC.

In addition, remove dependency on --long since this test case does not
really take that long (just couple of seconds).

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-27 19:24:33 +02:00
Jouni Malinen
b98445f6ba tests: Optimize p2p_go_move_scm initial wait
There is no need to wait for the initial client timeout in this type of
test sequence since that wait can be cleared by connecting and
disconnecting a client to the group. This allows the test case to be
executed much more quickly and the dependency on --long can be removed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-27 19:22:30 +02:00
Jouni Malinen
262825e896 tests: Convert p2p_go_move_scm to use dynamic hwsim
Use a dynamically added HWSimRadio to allow the MCC case to be covered
with a single test run with the mac80211_hwsim default radios disabling
MCC.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-27 19:14:38 +02:00
Jouni Malinen
1002684e11 tests: Convert p2p_go_move_active to use dynamic hwsim
Use a dynamically added HWSimRadio to allow the MCC case to be covered
with a single test run with the mac80211_hwsim default radios disabling
MCC.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-27 19:11:27 +02:00
Jouni Malinen
78fdab307e tests: Dynamic hwsim p2ps_channel_active_go_and_station_different_mcc
Convert p2ps_channel_active_go_and_station_different_mcc to use a
dynamically added HWSimRadio to allow the MCC case to be covered with a
single test run with the mac80211_hwsim default radios disabling MCC.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-27 19:01:10 +02:00
Jouni Malinen
53401e919e Abort ongoing scans on FLUSH command
This may speed up some hwsim test case sequencies by avoiding a wait for
a scan at the end of a test case to complete.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-27 01:09:42 +02:00
Jouni Malinen
d2e7cfc0bd tests: Use wlantest without capture file write buffering
This makes the run_tshark() operations more reliable while still
allowing to reduce the extra wait by forcing wlantest to flush the
packets to the pcapng file.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-27 00:12:38 +02:00
Jouni Malinen
e929eb39d6 wlantest: Add -N command line argument to remove write buffering
This makes it easier to do live parsing of captured pcap files from
wlantest without having to rename and restart the capture file. Packet
writes are flushed to disk after each packet if -N is included in the
command line.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-27 00:10:53 +02:00
Jouni Malinen
b25f04d44a tests: Clean up frequency list in scan_dfs
This makes the test log more readable by converting the values to
integers and sorting the array.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 23:42:30 +02:00
Jouni Malinen
3960585785 tests: VHT with 80 MHz channel width and local power constraint
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 20:41:55 +02:00
Rajkumar Manoharan
3c417499e7 hostapd: Add Transmit Power Envelope IE when VHT is enabled
Add Transmit Power Envelope element defined in IEEE P802.11-REVmc/D4.3,
8.4.2.161.

Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
2015-11-26 20:40:24 +02:00
Jouni Malinen
7767687109 tests: Abort scan
This verifies the nl80211 behavior to abort a scan on an explicit
control interface request and on connection request.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 19:44:14 +02:00
Jouni Malinen
2ea2166d5a Add control interface command for aborting an ongoing scan
The new ABORT_SCAN command can be used to request an ongoing scan to be
aborted.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 19:44:14 +02:00
Kanchanapally, Vidyullatha
4ead7cfd5d Abort an ongoing scan before connect
Connect radio work is sometimes delayed for a considerable duration if
there is an ongoing scan radio work. To avoid these delays abort the
ongoing scan on that interface before queuing a connect request. Upon a
scan done indication from the driver, connect radio work will be
scheduled.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 19:44:14 +02:00
Kanchanapally, Vidyullatha
4f30addb38 nl80211: Add support for aborting an ongoing scan
This adds the driver interface commands for issuing a request to abort
an ongoing scan operation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 19:44:14 +02:00
Jouni Malinen
5ef0b84355 Sync with mac80211-next.git include/uapi/linux/nl80211.h
This brings in nl80211 definitions as of 2015-11-26.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-26 19:42:56 +02:00
Jouni Malinen
f9bf222552 tests: Scan on DFS channels
This is a test case for mac80211 behavior regarding active scanning on
DFS channels.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 19:24:25 +02:00
Jouni Malinen
a74a1e4eab tests: Open mesh network on VHT 80+80 MHz channel
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 18:47:40 +02:00
Jouni Malinen
13f6ef9c79 tests: IBSS on VHT 80+80 MHz channel
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 18:47:40 +02:00
Jouni Malinen
0530eb1086 mesh: Clear wpa_s cipher selection on starting mesh
This is needed to avoid hitting WEP/TKIP detection in
ibss_mesh_setup_freq() if the previous connection used WEP or TKIP.
Previously, that could have resulted in VHT and HT getting disabled for
the mesh connection.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 18:47:40 +02:00
Jouni Malinen
1d6955e668 nl80211: Fix SIGNAL_POLL in IBSS and mesh
NL80211_CMD_GET_STATION does not work with the IBSS/mesh BSSID, so clear
the signal strength instead of returning failure when SIGNAL_POLL is
used in an IBSS/mesh.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 17:57:07 +02:00
Ahmad Kholaif
0f29bc68d1 IBSS/mesh: Add support for VHT80P80 configuration
A new network profile configuration parameter max_oper_chwidth=3 can be
used to specify preference to enable 80+80 MHz VHT channel for IBSS. If
that is set, the first 80 MHz segment is specified based on the
frequency parameter in the network profile and the second segment is
selected automatically (which will practically be limited to a single
possibility due to DFS requirements in most countries).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 17:47:15 +02:00
Jouni Malinen
05032725e1 tests: P2P client joining a group before having found GO Device Address
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 15:17:36 +02:00
Jouni Malinen
bcf4e38c5f tests: AP with open mode and REASSOCIATE not finding a match
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 12:23:19 +02:00
Jouni Malinen
35b61a496a tests: Verify P2P group formation with 80+80 MHz channel
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-25 22:43:38 +02:00
Ahmad Kholaif
c27f4c9006 P2P: Add support for VHT 80+80 MHz and 160 MHz
The new max_oper_chwidth and freq2 arguments to P2P_CONNECT, P2P_INVITE,
and P2P_GROUP_ADD control interface commands can be used to request
larger VHT operating channel bandwidth to be used than the previously
used maximum 80 MHz.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-25 19:01:20 +02:00
Ahmad Kholaif
bee5d8e067 nl80211: Add VHT 160 MHz channel flags
This extends the previous design that covered only the VHT 80 MHz cases
for VHT channel flags. New functions are introduced to allow 160 MHz
bandwidth cases to determine the center channel and check availability
of a 160 MHz channel.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-25 19:01:14 +02:00
Ahmad Kholaif
5e1da9c8fd P2P: Define operating classes for VHT 80+80 and 160
This adds definitions for the global operating classes 129 and 130 for
VHT 80+80 MHz and 160 MHz use cases.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-25 19:01:10 +02:00
Dedy Lansky
ea7081185e FST: Improve parsing of Multiband IEs
Previously, MB IEs were parsed only from association event. Try to get
MB IEs from other management frames like Probe Response frames. The MB
IEs from the association event may not be up-to-date and in some cases
may actually be missing and updating the information based on other
frames can improve robustness of FST exchanges.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-25 17:33:31 +02:00
Anton Nayshtut
b47d05aa45 FST: Make FST peer connection check more permissive in hostapd
Modify the FST peer connection check so it won't skip peers without MB
IEs making it more permissive for peers that didn't provide MB IEs
during association request. This can be helpful, e.g., in cases where a
STA's interface connected before it was added to the FST group. This
allows the AP to receive FST Action frames and initiate session with a
STA via STA's interface that doesn't expose MB IEs.

The adjusted FST protocol is still safe, as it protects itself in many
other ways (checking band info and it's accordance to the interfaces,
Setup IDs, connection states of the interfaces involved, etc.)
effectively avoiding all types of invalid situations.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-25 17:30:59 +02:00
Jouni Malinen
08e47376ec tests: Import p2p_utils instead of functions from old locations
These couple of files were forgotten when moving P2P helper functions
into the new p2p_utils.py file.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-25 15:47:16 +02:00
Johannes Berg
f2a438f51d tests: Print test name to kernel log buffer
Print the test name to the kernel log buffer so debugging
cross-test issues becomes easier.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-24 16:28:24 +02:00
Jouni Malinen
39c3c9b7dc Remove wpa_supplicant/tests
There was only a single file remaining in this directory. All the other
old test functionality has been moved under the top level tests
directory. Move the remaining file to the wpa_supplicant directory to
get rid of the subdirectory.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-24 00:00:21 +02:00
Jouni Malinen
1fff13a9cb tests: Move EAP-SIM PRF module test into the hwsim framework
The old wpa_supplicant/Makefile target test-eap_sim_common did not work
anymore and anyway, this test is better placed in the newer hwsim
framework to make sure the test case gets executed automatically.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-24 00:00:21 +02:00
Jouni Malinen
9b635d0bde Remove link_test and test_wpa
These wpa_supplicant test programs have not been maintained for years
and it would take significant effort to get these into working state.
Since there does not seem to be any real need for these based on lack of
maintenance, it is easier to just drop these tools for now.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-24 00:00:21 +02:00
Jouni Malinen
9e68742ef1 Fix CONFIG_NO_WPA=y build
Number of places were calling functions that are not included in
CONFIG_NO_WPA=y build anymore. Comment out such calls. In addition, pull
in SHA1 and MD5 for config_internal.c, if needed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-23 23:34:52 +02:00
Jouni Malinen
eb926f1257 Comment out wpas_reenabled_network_time with CONFIG_NO_SCAN_PROCESSING
This removes a compiler warning about unused function.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-23 23:33:55 +02:00
Anton Nayshtut
81822ce688 tests: Make FST tests aware of unconditional station's MB IE exposure
This syncs the test cases with the implementation change in station's MB
IE creation. FST tests should expect MB IE regardless of the station
connection state and whether the current connection is FST-enabled or
not. This fixes the follow test cases that started reporting failures
with the previous commit change in src/fst/fst_group.c:
fst_disconnect_1_of_2_stas_from_non_fst_ap
fst_sta_connect_to_non_fst_ap
fst_second_sta_connect_to_non_fst_ap
fst_disconnect_2_of_2_stas_from_non_fst_ap
fst_second_sta_connect_to_fst_ap
fst_disconnect_1_of_2_stas_from_fst_ap

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-23 20:36:54 +02:00
Anton Nayshtut
f231b3d816 FST: Fix STA MB IEs creation
FST STA should always expose its MB IEs regardless of its connection
state and whether the connected AP is currently FST-enabled or not.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-23 20:36:12 +02:00
Ilan Peer
edb63af6ba tests: Test no P2P GO move when invitation is in progress
Add a test to verify that a P2P GO does not start a CSA
once invitation signalling is done, and the P2P client is
about to connect.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-11-22 22:16:32 +02:00
Ilan Peer
ed7820b484 P2P: Add a testing option to force P2P GO CSA
Add a testing option to force a P2P GO CSA on successful
invitation to join an active P2P GO.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-11-22 21:49:19 +02:00
Ilan Peer
6cbbae2cf8 P2P: Set p2p_go_wait_client in invitation_result() cb
When an invitation to join an existing group is accepted by the
peer device, set p2p_go_wait_client to the current time so
that wpas_p2p_in_progress() would return != 0, thus preventing
P2P CSA, scanning etc., that would interfere with the peer
device connection.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-11-22 21:46:43 +02:00
Jouni Malinen
845d48c133 tests: Make dbus_p2p_group_idle_timeout more robust
This test case was failing if a PropertiesChanged signal for P2P peer
gets delivered from a previous test case. Avoid that by waiting for the
new group to be formed before processing any PropertiesChanged signals.

This failure was triggered by the following test case sequence:
dbus_p2p_two_groups dbus_p2p_group_idle_timeout

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-22 21:28:49 +02:00
Somdas Bandyopadhyay
83702b6088 Android: Give user the option for selecting browser for HS 2.0 OSU
When built with browser-android.c, hs20-osu-client used to always launch
the native/stock Android browser for OSU user interaction. This browser
is not present in all devices. It is better to give the option to the
user to select his/her browser.

Here the user will be shown a pop up to select the browser that he/she
wants.

Signed-off-by: Somdas Bandyopadhyay <somdas.bandyopadhyay@intel.com>
2015-11-22 21:06:17 +02:00