If the previously started setup is terminated in case both peers
initiate TDLS link at more or less the same time, disable the old link
to allow the dummy station entry to be deleted from cfg80211 so that a
new entry can be added for the setup direction that will be allowed to
proceed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add NL80211_CMD_UPDATE_FT_IES to support update of FT IEs to the
WLAN driver. Add NL80211_CMD_FT_EVENT to send FT event from the
WLAN driver. This will carry the target AP's MAC address along
with the relevant Information Elements. This event is used to
report received FT IEs (MDIE, FTIE, RSN IE, TIE, RICIE).
Signed-off-by: Deepthi Gowri <deepthi@codeaurora.org>
It is possible for a P2P client to connect to an operating group without
exchanging any Probe Request/Response frames that would allow the GO to
discover the peer. To make sure there is a P2P peer entry at the GO, try
to add the peer information based on P2P IE in (Re)Association Request
frame.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for VHT capability overrides to allow testing connections
with a subset of the VHT capabilities that are actually supported by
the device. The only thing that isn't currently supported (by mac80211
and this code) is the RX/TX highest rate field.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This implements support for the new NL80211_ATTR_SPLIT_WIPHY_DUMP in
nl80211 to handle wiphy information that cannot fit in one message.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-hostap: Dennis H Jensen <dennis.h.jensen@siemens.com>
The peer commit element needs to be validated to pass one of the steps
listed in IEEE 802.11, 11.3.5.4:
scalar-op(r, ELEMENT) = 1 modulo p
Similar step was present for ECC groups, but was missing for FFC groups.
This is needed to avoid dictionary attacks.
Thanks to Michael Roßberg and Sascha Grau for reporting this.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is clearer to keep all the validation steps described in IEEE 802.11
11.3.5.4 in a single location instead of splitting this between the
parsing and processing functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
Peer device includes its list of allowed operating channels in the
Invitation Response frame. When we are becoming the GO, use that list
from the peer to filter out acceptable channels to avoid selecting a
channel that the peer is unable to use.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When re-invoking a persistent group in P2P client role, the new
pref=<MHz> parameter can now be used with the p2p_invite command to
indicate a preferred operating frequency. Unlike the older freq=<MHz>
parameter, this leaves GO an option to select another channel (from our
supported channels) if the GO cannot accept the channel.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If multi channel concurrency is supported, we have to populate the
p2p_channels with list of channels that we support. Use the same design
that was previously added for GO Negotiation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The VHT IE struct just has an opaque 8-byte array for the MCS
set, make it more expressive by explicitly naming the pieces.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Commit fb8984fd6f cleared wps_method to
WPS_NOT_READY in p2p_stop_find_for_freq() as an attempt to clear
authorization when a group formation is cancelled. However, this code
path is hit also in cases where the user did not actually cancel
anything (e.g., from p2p_process_go_neg_req()). As such, it is not fine
to clear wps_method here even if it could be proper for some cases. For
now, revert that part to avoid regressions and consider clearing
wps_method on cancel separately.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In case we have replied to a peer's GO Negotiation Request frame with a
GO Negotiation Response frame using status code
info-currently-unavailable (1), the peer is likely going to wait for us
to initiate GO Negotiation on its Listen channel. We were previously
using alternativing send-GO-Neg-Req and Listen phase when providing that
response after the user had authorized the connection. However, the
Listen phase here is unnecessary in this case and will make the
connection take longer time to go through. Skip the Listen phase and
make the wait-for-GO-Neg-Resp timeout random between 100 and 200 ms to
avoid getting in sync with the peer. In practice, this will make us
retry GO Negotiation Request frames more frequently and remain on the
peer's Listen channel for most of the time when initiating GO
Negotiation after status=1 response.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There may be environments in which large number of devices are operating
on the social channels. In such cases, it is possible for the Action
frame TX operation wait for quite long time before being able to get the
frame out. To avoid triggering GO Negotiation failures, increase the
timeouts for GO Neg Req (with TX ACK) and GO Neg Resp (with or without
TX ACK as long as status=0) to 500 ms.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This flag will add ==== delimiter between to separate bss results.
Unlike the other BSS command MASK values, this delimiter is not
included by default to avoid issues with existing users of the BSS
command.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
It is possible for the driver to indicate multiple Probe Request frames
that would be processed in a single loop. If those frames happen to be
from a peer which with we are trying to start GO Negotiation, multiple
timeouts to start GO Negotiation (p2p_go_neg_start) could end up being
scheduled. This would result in confusing burst of multiple GO
Negotiation Request frames being sent once the RX loop finally
concludes. Avoid this by scheduling only a single eloop timeout to
trigger GO Negotiation regardless of how many Probe Request frames from
the peer is received. In addition, make sure this timeout gets canceled
in p2p_deinit().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we have already sent out GO Negotiation Response and are waiting for
the peer to reply with GO Negotiation Confirm, there is no point in
re-starting GO Negotiation based on Probe Request frame from the peer.
Doing that would just result in confusing GO Negotiation exchange with
multiple sessions running at the same time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The device that is selected as the GO shall incode P2P Group ID
attribute in GO Negotiation Response/Confirm message. Previously we did
not reject a message without that attribute since it was possible to
continue operations even without knowing the SSID. However, this can
potentially result in confusing results since missing P2P Group ID
attribute can be a sign of conflicting GO role determination (both
devices assuming the peer is the GO). To get clearer end result for the
GO Negotiation, reject this as a fatal error. In addition, stop GO
Negotiation if GO Negotiation Confirm indicates non-zero status since
that is also a fatal error.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 624b4d5a64 changed GO Negotiation
to use the same Dialog Token value for all retransmissions of the GO
Negotiation Request within the same session. However, it did leave the
tie breaker bit changing for each frame. While this should not have
caused issues for most cases, it looks like there are possible sequences
where the peer may end up replying to two GO Negotiation Request frames
with different tie breaker values. If in such a case the different GO
Negotiation Response frames are used at each device, GO role
determination may result in conflicting results when same GO intent is
used.
Fix this by assigning the tie breaker value at the same time with the
dialog token (i.e., when processing the p2p_connect command instead of
for each transmitted GO Negotiation Request frame) to avoid issues with
GO selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's VHT capability is required for the
driver to establish a TDLS link in VHT mode with a compatible peer.
Pass this information to the driver when the peer station is
getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
WSC specification 2.0 section 7.4 describes OOB password to be expressed
in ASCII format (upper case hexdump) instead of raw binary.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 2d9ffe1e85 broke GAS server
callback for receiving Public Action frames. The incorrect context
pointer was used in the public_action_cb2 case. Fix this to use the
correct context pointer.
Signed-hostap: Jouni Malinen <j@w1.fi>
Hostapd provides QoS info of the STA (Service Period & AC mask) to the
kernel during wpa_driver_nl80211_sta_add call. Bit 5 and Bit 6 of QoS
info represents the Max SP length. Fix an issue in the code to fetch the
Max SP by shifting right the QoS info by value WMM_QOSINFO_STA_SP_SHIFT.
(operator ">" is replaced with ">>" operator).
Signed-off-by: Srinivasan <srinivasanb@posedge.com>
"WPS_NFC_TOKEN <WPS/NDEF>" used to generate a new NFC password token
regardless of whether there was a pre-configured token in the
configuration. Change this to use the pre-configured value, if
available, instead. This allows the same command to be used to write the
password token to an NFC tag more conveniently.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The contents of the peer's capability and extended capability
information is required for the driver to perform TDLS P-UAPSD and Off
Channel operations. Pass this information to the driver when the peer
station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The information of the peer's HT capability and the QOS information is
required for the driver to perform TDLS operations. Pass this
information to the driver when the peer station is getting added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Registrar is allowed to propose another Device Password ID in M2. Make
Enrollee validate Device Password ID in M2 to check if this happened.
This commit adds support for changing from NFC password token to default
PIN for the case where the AP is the Enrollee and has both the NFC
password token and AP PIN enabled at the same time.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit ffdaa05a6b added support for using
NFC password token from an AP. However, it had a bug that prevented the
wpa_supplicant wps_reg command from being used with "nfc-pw" as the PIN
value. Fix string comparison to handle this correctly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A TDLS Teardown frame with Reason Code 3 (Deauthenticated because
sending STA is leaving (or has left) IBSS or ESS) shall be transmitted
to all TDLS peer STAs (via the AP or via the direct path) prior to
transmitting a Disassociation frame or a Deauthentication frame to the
AP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The driver may have cached (e.g., in cfg80211 BSS table) the scan
results for relatively long time. To avoid reporting stale information,
update P2P peers only based on results that have based on frames
received after the last p2p_find operation was started.
This helps especially in detecting when a previously operating GO stops
the group since the BSS entry for that could live for 30 seconds in the
cfg80211 cache. Running p2p_flush followed by p2p_find will now allow
wpa_supplicant to not add a P2P peer entry for that GO if the group had
been terminated just before that p2p_flush command. Previously, that GO
could have been indicated as a newly found device for up to 30 seconds
after it had stopped the group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
For various P2P use cases, it is useful to have more accurate timestamp
for the peer information update. This commit improves scan result
handling by using a single timestamp that is taken immediately after
fetching the results from the driver and then using that value to
calculate the time when the driver last updated the BSS entry. In
addition, more debug information is added for P2P peer updates to be
able to clearly see how old information is being used here.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we discover a P2P peer based on a Beacon frame from the GO role, we
do not get information about the supported configuration methods. This
can result in issues if the P2P managing entity above wpa_supplicant is
not prepared to handling config_methods=0x0. To avoid this, postpone
reporting of the P2P-DEVICE-FOUND event when this happens on one of the
social channels. It would be good to be able to this on all channels,
but that could result in issues of never indicating the event for a peer
that is operating a GO on a channel that requires passive scanning.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It could be possible for the scan results to include two entries for a
peer, one from the Listen state and the second one from the GO role. The
latter could be based on a Beason frame. If that happens and the entry
from GO is processed last, the P2P peer config_methods value could
potentially get cleared since Beacon frames do not include this
information in either WPS or P2P element. Avoid this by allowing the
config_methods value for P2P peers to be updated only if the new value
is non-zero.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since there could be multiple carrier records, it is cleaner to build
only the WPS carrier record instead of full NFC connection handover
request within wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
Control interface command "NFC_GET_HANDOVER_SEL NDEF WPS-CR" can now be
used to fetch WPS carrier record from hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
The capability itself isn't really affected by an OBSS
scan, only the HT operation must then be restricted to
20 MHz. Change this, and therefore use the secondary
channel configuration to determine the setting of the
OP_MODE_20MHZ_HT_STA_ASSOCED flag.
This shouldn't really change anything functionally,
it just makes the code a little less confusing and
is also needed to implement more dynamic bandwidth
changes if ever desired.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This adds a new getSessionId() callback for EAP peer methods to allow
EAP Session-Id to be derived. This commits implements this for EAP-FAST,
EAP-GPSK, EAP-IKEv2, EAP-PEAP, EAP-TLS, and EAP-TTLS.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In addition to the offload mechanism, the Android configuration and
makefiles are extended to allow this to be configured for the build by
dropping in platform specific configuration files and makefile without
having to modify any existing files.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
ANDROID_SETGROUPS_OVERRIDE macro can now be used to override setgroups()
values based on build configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When pending p2p_find fails we need to send p2p_stop_find event to
indicate the previous p2p_find command has been processed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 1a9f6509b3 added support for
fragmenting the P2P IE in Probe Response frames from a GO. However, it
did not take into account the possibility of Wi-Fi Display IE being
included in the same buffer and caused a regression for the cases where
Wi-Fi Display is enabled. Fix this by building the possibly fragmented
P2P IE first and then concatenating the separate IEs together.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
On the DMG (60 GHz) band, capability bits defined differently from
non-DMG ones. Adjust capability matching to cover both cases.
Also, for non-DMG bands, check ESS bit is set.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
When AP mode operation reject the client, nl80211 layer advertises the
connect failed event with the reason for failures (for example, max
client reached, etc.) using NL80211_CMD_CONN_FAILED.
This patch adds some debug messages whenever such an event is received
from the nl80211 layer and also the same event is posted to the upper
layer via wpa_msg().
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
The reason code used for calculating the MIC should correspond to the
reason code with which the teardown frame is sent, as the receiver shall
use the one obtained in the frame for validating the MIC.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If an implicit TDLS set up request is obtained on an existing link or an
to be established link, the previous link was not removed. This commit
disables the existing link on a new set up request. Also,
wpa_tdls_reneg() function was invoking wpa_tdls_start() on an already
existing peer for the case of internal setup, which is incorrect. Thus
the invocation of wpa_tdls_start() is removed in wpa_tdls_reneg() and
also this function is renamed to wps_tdls_remove() as it does not
renegotiation rather shall remove the link (if any) for the case of
external setup.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to have this check copied to each caller since this
needs to be done for every case when a new peer is being added.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Peer entries were getting added on every discover request from the peer,
thus resulting in multiple entries with the same MAC address. Ensures
that a check is done for the presence of the peer entry and reuse the
existing entry instead of adding a new one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
GAS server used the same public_action_cb mechanism as P2P to process
Action frames. This ended up overriding P2P processing of Action frames
while running an AP/GO interface with a build that enables Interworking
(e.g., for Hotspot 2.0) and a driver that uses hostapd for AP mode
SME/MLME. Fix this by adding a separate callback registration for the
GAS server. This should really be cleaned up by supporting arbitrary
number of callback handlers, but for now, this addresses the regression
with a minimal change.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Very basic support for OpenBSD. No support for scanning yet, so this needs
ap_scan=0 and expects that the user has configured the interface manually
using ifconfig(8).
Signed-hostap: Mark Kettenis <kettenis@openbsd.org>
Commit 6aaac006af modified the
pmksa_cache_init() prototype, but forgot to update the empty wrapper
function which is used when PMKSA caching is not included in the build.
Signed-hostap: Jouni Malinen <j@w1.fi>
When scan failed, the wpa_driver_nl80211_scan method tried
to recursively call itself, but it passed in the wrong argument
for the void*, and so then it crashed accessing bad memory.
With this fix, hostapd still will not retry the scan later, but
at least it will exit cleanly and won't polute the file system
with core files.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The P2P-FIND-STOPPED event was sent only in the P2P_SEARCH state, but
this needs to be send also in the new continue-search-when-ready states
P2P_CONTINUE_SEARCH_WHEN_READY and P2P_SEARCH_WHEN_READY for consistent
behavior.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Signal the start of EAP authentication as well as when additional
credentials are required to complete.
Signed-hostap: Paul Stewart <pstew@chromium.org>
This was previously included only with NL80211_CMD_ASSOCIATE, but the
information is as useful (if not even more useful) for
NL80211_CMD_CONNECT. It should be noted that cfg80211 does not yet use
this attribute with NL80211_CMD_CONNECT, but that can be added easily.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Each GO Negotiation Request is (re)tried with an unique dialog token and
a GO Negotiation Response / Confirmation from the peer with a mismatched
dialog token is ignored which could result in a failure in this group
formation attempt. Thus, the P2P device would continue retrying the GO
Negotiation Request frames till the GO Negotiation Response frame with a
matching dialog token is received. To avoid the failures due to the
dialog token mismatch in retry cases if the peer is too slow to reply
within the timeout, the same dialog token value is used for every retry
in the same group formation handshake.
It should be noted that this can result in different contents of the GO
Negotiation Request frame being sent with the same dialog token value
since the tie breaker bit in GO Intent is still toggled for each
attempt. The specification is not very clear on what would be the
correct behavior here. Tie breaker bit is not updated on
"retransmissions", but that is more likely referring to the layer 2
retransmission and not the retry at higher layer using a new MMPDU.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows even more memory to be freed when the SAE instance enters
Accepted state. This leaves only the minimal needed memory allocated
during the association which is especially helpful for the AP
implementation where multiple stations may be associated concurrently.
Signed-hostap: Jouni Malinen <j@w1.fi>
Most of the variables are not needed anymore once the SAE instance
has entered Accepted state. Free these to save memory.
Signed-hostap: Jouni Malinen <j@w1.fi>
The rand/mask values and commit scalar are derived using the exact same
operations, so only use a separate function for deriving the commit
element.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need to postpone this validation step to a separate
processing operation for the commit message, so move the minimal
validation tasks into the parsing functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
Move the bignum comparison part into the bignum library to allow a
single implementation of rand generation for both ECC and FCC based
groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
The groups 22, 23, and 24 are not based on a safe prime and generate a
prime order subgroup. As such, struct dh_group is also extended to
include the order for previously defined groups (q=(p-1)/2 since these
were based on a safe prime).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows FFC groups to be used with SAE. Though, these groups are not
included in the default sae_groups value based on what is available
since the FFC groups have the additional requirement of using a safe
prime with the current implementation (or specification of the group
order).
Signed-hostap: Jouni Malinen <j@w1.fi>
The optional "reason=<reason code>" parameter to the ctrl_iface
deauthenticate and disassociate commands can now be used to change the
reason code used in the disconnection frame. This can be used, e.g., by
P2P GO to disconnect a single P2P client from the group by sending it an
indication of the group getting terminated (Deauthentication frame with
reason code 3). It needs to be noted that the peer device is still in
possession on the PSK, so it can still reconnect to the group after this
if it does not follow the group termination indication.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit increases the maximum buffer size for P2P Client Info
advertized by the Group Owner in the Probe Response frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use of two variables to track bounds checking seems to be a bit too much
for some static analyzers, so add an extra condition for buffer padding
to avoid incorrect warnings.
Signed-hostap: Jouni Malinen <j@w1.fi>
These verify that a proper pointer type is used and in addition, seems
to get rid of some false static analyzer warnings.
Signed-hostap: Jouni Malinen <j@w1.fi>
The code initializing GMK Counter uses the group pointer value as extra
entropy and to distinguish different group instances. Some static
analyzers complain about the sizeof(pointer) with memcpy, so use a more
explicit type casting to make it more obvious what the code is doing.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd.conf sae_groups parameter can now be used to limit the set of
groups that the AP allows for SAE. Similarly, sae_groups parameter is
wpa_supplicant.conf can be used to set the preferred order of groups. By
default, all implemented groups are enabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
In addition to the trivial change in adding the new group ientifier,
this required changes to KDF and random number generation to support
cases where the length of the prime in bits is not a multiple of eight.
The binary presentation of the value needs to be shifted so that the
unused most significant bits are the zero padding rather than the extra
bits in the end of the array.
Signed-hostap: Jouni Malinen <j@w1.fi>
In addition to the mandatory group 19 (256-bit random ECP group) add
support for groups 20 (384-bit), 25 (192-bit), and 26 (224-bit).
Signed-hostap: Jouni Malinen <j@w1.fi>
The counter>200 check needs to be done before the continue-on-not-found
case to be effective in stopping this loop.
Signed-hostap: Jouni Malinen <j@w1.fi>
The buffer is set based on maximum group prime length, but pwd-value
needs to be correct length for the negotiated group.
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes the SAE implementation a bit simpler by not having to build
the bignum for group order during execution.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd can now be configured to use anti-clogging mechanism based on
the new sae_anti_clogging_threshold parameter (which is
dot11RSNASAEAntiCloggingThreshold in the standard). The token is
generated using a temporary key and the peer station's MAC address.
wpa_supplicant will re-try SAE authentication with the token included if
commit message is rejected with a token request.
Signed-hostap: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2012, 11.3.8.6.1: If there is a protocol instance for
the peer and it is in Authenticated state, the new Commit Message
shall be dropped if the peer-scalar is identical to the one used in
the existing protocol instance.
Signed-hostap: Jouni Malinen <j@w1.fi>
The enum values for struct sae_data::state now match the protocol
instance states as defined in IEEE Std 802.11-2012, 11.3.8.2.2
Signed-hostap: Jouni Malinen <j@w1.fi>
Even if the PAC file does not start with the proper header line, allow
the file to be used if it is empty. [Bug 423]
Signed-hostap: Jouni Malinen <j@w1.fi>
The PMKSA cache expiration timer was not actually ever initialized since
the only place for registering the timeout was in the timeout handler.
Fix this by initializing the timer whenever a new PMKSA cache entry is
added to the beginning of the list (i.e., when it was the first entry or
expires before the entry that was previously going to expire first).
[Bug 393]
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 4378fc14eb started using QoS Data
frames for QoS STAs. It used the correct flags value for WPA/RSN
EAPOL-Key frames, but wrong flags for IEEE 802.1X EAPOL frames. The
WPA_STA_WMM value used in driver_nl80211.c happens to be identical to
WLAN_STA_ASSOC in sta->flags and this makes driver_nl80211.c try to use
QoS header for all STAs. Fix this by properly converting the flags from
WLAN_STA_* to WPA_STA_*. [Bug 426]
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 68a41bbb44 broke fallback from
reauth id to fullauth id by not allowing a second AKA/Identity round to
be used after having received unrecognized reauth_id in the first round.
Fix this by allowing fullauth id to be requested in such a case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 175171ac6c ensured that the PD
requests are retried in join-a-running group case and the Enrollee is
started on either receiving the PD response or after the retries. Each
PD request is retried with an unique dialog token and a PD response from
the GO with a mismatched dialog token is ignored. Thus, the P2P client
would continue retrying the PD requests till the response with a
matching dialog token is obtained. This would result in the GO getting
multiple PD requests and a corresponding user notification (POP UP) in
implementations where each PD request results in a POP UP, resulting in
a bad user experience. To avoid such behavior, the same dialog token
value is used for every retry in the same PD exchange.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_driver_nl80211_ap() returned error if set_freq failed, but left the
previously set nlmode to GO/AP. While this should not be issue for most
purposes, it leaves the interface in somewhat unexpected state and could
potentially affect operations prior to next connection attempt. Address
this by restoring the previous nlmode if AP mode cannot be started for
some reason.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to read the code for the two possible cases
(forced/preferred channel and automatic channel selection).
Signed-hostap: Jouni Malinen <j@w1.fi>
Since the operating channel is randomly set to 1/6/11 on init, which is
commonly included in the channel intersection, we were effectively
ignoring the set of P2P preferred channels when trying to improve
channel selection after having received peer information. Fix this by
trying to get the best channel we can, unless the user hard coded the
operating channel in the configuration file or p2p_connect command. Fall
back to the initial randomly selected channel if a better one cannot be
chosen.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Even if the peer does not accept the forced channel, we should not allow
the forced_freq parameter to be be overridden, i.e., such a case needs
to result in GO Negotiation failure.
Signed-hostap: Jouni Malinen <j@w1.fi>
Both p2p_connect and p2p_authorize use the same functionality to select
the channel preferences for GO Negotiation. The part of setting this
device flag was copied to each function, but it can also be handled by
the shared function after some reordering of code.
Signed-hostap: Jouni Malinen <j@w1.fi>
The exact same mechanism was used for determining the operating channel
at the device that becomes the GO regardless of whether this was
triggered by reception of GO Negotiation Request of Response frame. Use
a shared function to avoid duplicated implementation and potential
differences in the future.
Signed-hostap: Jouni Malinen <j@w1.fi>
When no other user preference is specified, opt to use an operating
channel that allows HT40 operation. This way, if driver capabilities
and regulatory constraints allow, we might enjoy increased bandwidth.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
cfg80211 caches the scan results according the channel number. Due to
the 15 sec aging this might cause the user mode to see more than one
scan result with the same BSSID, e.g. - one scan result for the
P2P Device and one for the P2P GO (once it's enabled).
Fix this by updating the device entry only if the new peer entry is
newer than the one previously stored.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Add some more functionality for BSS Transition Management:
- advertise support for BSS Transition Management in extended
capabilities element
- add hostapd.conf parameter bss_transition=1 for enabling support
for BSS Transition Management
- add "hostapd_cli disassoc_imminent <STA> <num TBTTs>" for sending
disassociation imminent notifications for testing purposes
- wpa_supplicant: trigger a new scan to find another BSS if the
current AP indicates disassociation imminent (TODO: the old AP needs
to be marked to use lower priority to avoid re-selecting it)
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd can run with different VIF when using nl80211. Events about MIC
failures have to be processed in context of the VIF which received it
and not in context of the primary VIF. Otherwise the station belonging
to this VIF may not be found in the primary VIF station hash and
therefore no countermeasures are started or the countermeasures are
started for the wrong VIF.
Signed-hostap: Sven Eckelmann <sven@open-mesh.com>
Signed-hostap: Simon Wunderlich <simon@open-mesh.com>
This optional attribute may make it easier to bind together the
Access-Request and Accounting-Request messages. The accounting session
identifier is now generated when the STA associates instead of waiting
for the actual session to start after successfull authentication.
Signed-hostap: Jouni Malinen <j@w1.fi>
Basic support for the 60 GHz band. Neither P2P nor WPS are yet taken
care off. Allows to start AP with very simple config:
network={
ssid="test"
mode=2
frequency=60480
key_mgmt=NONE
}
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The config says that the default for ap_table_max_size is 255 and the
default for ap_table_expiration_time is 60. But the code doesn't reflect
the default values mentioned in the sample config file.
These variables completely disable the code for Overlapping Legacy BSS
Condition by default when they are not correctly initialized. WFA
certification requires this feature and therefore an AP would have
failed the certification process unless they were initialized manually
using the configuration file.
Signed-hostap: Sven Eckelmann <sven@open-mesh.com>
Signed-hostap: Simon Wunderlich <simon@open-mesh.com>
WSC IE in Beacon and Probe Response frames should behave consistently
as far as the RF Bands attribute is concerned. Use the same dualband
condition for adding this into Probe Response frames since the value
is not really needed if the AP is not a dualband AP.
Signed-hostap: Jouni Malinen <j@w1.fi>
If separate hostapd processes are used for different RF bands, the
dualband parameter for WPS was not set correctly. Allow dualband
indication (mainly, addition of RF bands attribute for PBC session
overlap detection) also based on wps_rf_bands value (if set to "ag").
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows Probe Request frame processing to compare the configured
SSID to the SSID List element in addition to the SSID element.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace CONFIG_IEEE80211V with CONFIG_WNM to get more consistent build
options for WNM-Sleep Mode operations. Previously it was possible to
define CONFIG_IEEE80211V without CONFIG_WNM which would break the build.
In addition, IEEE 802.11v has been merged into IEEE Std 802.11-2012 and
WNM is a better term to use for this new functionality anyway.
Signed-hostap: Jouni Malinen <j@w1.fi>
These fields do not use AES keywrap. Instead, they are protected with
management frame protection (and not included if PMF is disabled).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Expiry can always trigger a deauthentication, but otherwise,
deauthentication should only happen when the *current* cache entry is
removed and not being replaced. It should not happen when the current
PMK just happens to match the PMK of the entry being removed, since
multiple entries can have the same PMK when OKC is used and these
entries are often removed at different times.
This fixes an issue where eviction of the oldest inactive entry due to
adding a newer entry to a full cache caused a deauthentication when the
entry being removed had the same PMK as the current entry.
Signed-hostap: Dan Williams <dcbw@redhat.com>
pmksa_cache_free_entry() takes care of updated the list head pointer
(pmksa->pmksa), so no need to do this change in the caller.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use the shared_secret pointer from RADIUS client implementation instead
of getting this from hostapd configuration data.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds support for multiple PSKs per station when using a RADIUS
authentication server to fetch the PSKs during MAC address
authentication step. This can be useful if multiple users share a
device but each user has his or her own private passphrase.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
Add pmf=1/2 to wpa_supplicant STATUS command output to indicate that PMF
was negotiated for the connect (1 = optional in this BSS, 2 = required
in this BSS).
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, PMF (protected management frames, IEEE 802.11w) could be
enabled only with a per-network parameter (ieee80211w). The new global
parameter (pmf) can now be used to change the default behavior to be PMF
enabled (pmf=1) or required (pmf=2) for network blocks that do not
override this with the ieee80211w parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
We enable this feature for non-SME drivers as well if
they explicitly indicate need for it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Add the configuration option vht_oper_centr_freq_seg1_idx
for the second segment of an 80+80 MHz channel and use it
when building the VHT operation IE.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
If netlink_init() fails on socket create or bind the cfg struct
provided as parameter is freed by netlink_init(). Callers of
netlink_init() also free this struct on their error paths leading
to double free.
Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
This allows the AP to figure out whether a station is a HS 2.0 STA
during the association and access any information that the STA may have
included in this element.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Change the maximum retry limit from 10 to 120 to match the behavior
used with GO Negotiation Request frames when trying to start GO
Negotiation with a peer that does not acknowledge frames (e.g., due
to being in sleep or on another channel most of the time).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The GO may be in sleep when we send a PD Request frame to indicate that
we are about to join a running group. Previously, this frame was not
retried more than normal low level retries. This can result in the GO
not getting the frame especially in cases where concurrent multi-channel
operations or aggressive sleep schedule is used since most drivers do
not yet synchronize with the GO's NoA before association.
Increase the likelihood of the GO receiving the PD Request frame by
retransmitting it similarly to the PD-for-GO-Negotiation case. Start
the actual join operation only after these retries have failed to get
an acknowledgment from the GO to give the connection attempt a chance
to succeed if the driver implements better NoA synchronization for it.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_prov_disc_req() used the join parameter to figure out whether the PD
request was a user initiated or not. This does not cover all use cases
of PD, so add a separate parameter to allow caller to indicate whether
the user requested the operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
CONFIG_SQLITE=y option can now be used to allow the eap_user_file text
file to be replaced with a SQLite database
(eap_user_file=sqlite:/path/to/sqlite.db). hostapd.eap_user_sqlite
shows an example of how the database tables can be created for this
purpose. This commit does not yet include full functionality of the
text file format, but at least basic EAP-TTLS/MSCHAPv2 style
authentication mechanisms with plaintext passwords can be used for
tests.
Signed-hostap: Jouni Malinen <j@w1.fi>
The NL80211_CMD_TDLS_OPER command can be used as an event based on a
recent cfg80211 commit, so add code to map that to internal
wpa_supplicant event to request TDLS link setup/teardown.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 296a34f0c1 changed hostapd to
remove the internal STA entry at the beginning of TKIP countermeasures.
However, this did not take into account the case where this is triggered
by an EAPOL-Key error report from a station. In such a case, WPA
authenticator state machine may continue processing after having
processed the error report. This could result in use of freed memory.
Fix this by stopping WPA processing if the STA entry got removed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some deployed station implementations implement WPS incorrectly and
end up causing PBC session overlap issues by indicating active PBC
mode in a scan after the WPS provisioning step. Work around this by
ignoring active PBC indication in a Probe Request from a station that
completed PBC provisioning during the last five seconds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commits 07783eaaa0 and
3da372fae8 removed the only users of the
disassociate() driver operation, so these driver wrapper functions can
also be removed now.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Change the nl80211 driver in wpa_supplicant to correctly handle
connecting to a new AP through cfg80211 without SME capability. As
before, the driver will disconnect from the previously associated AP,
but now we attempt to immediately connect to our intended AP. This
prevents us from blacklisting the AP we were trying to connect to
because of a semantic mismatch between cfg80211 and wpa_supplicant. The
disconnect/connect patch generates a local disconnect nl80211 event
which we discard because we're already correctly tracking the pending
association request.
In detail:
cfg80211 does not support connecting to a new BSS while already
connected to another BSS, if the underlying driver doesn't support
separate authenticate and associate commands. wpa_supplicant is written
to expect that this is a supported operation, except for a little error
handling that disconnects from the current BSS when roaming fails and
relies on autoconnect logic to reconnect later. However, this failure to
connect is incorrectly attributed to the new AP we attempted to
associate with, rather than a local condition in cfg80211.
The combined effect of these two conditions is that full-mac drivers
accessible through cfg80211 but without SME capability take a long time
to roam across BSS's because wpa_supplicant will:
1) Fail to associate for local reasons
2) Disconnect and return that the association request failed
3) Blacklist the association target (incorrectly)
4) Do a scan
5) Pick a less desirable AP to associate with
Signed-hostap: Christoper Wiley <wiley@chromium.org>
Commit deca6eff74 added a redundant call
to l2_packet_get_own_addr. Use the information we already have in
atheros_init.
Signed-hostap: Baruch Siach <baruch@tkos.co.il>
If identity round limit is reached, EAP-SIM/AKA session is terminated.
This needs to free the allocated message.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no point in the hapd_iface == NULL validate after this pointer
has been dereferences, so move the code dereferencing hapd_iface after
the check.
Signed-hostap: Jouni Malinen <j@w1.fi>
The UFD (USB flash drive) configuration method was deprecated in WSC
2.0. Since this is not known to be used, remove the UFD implementation
from hostapd and wpa_supplicant to allow the WPS implementation to be
cleaned up. This removes the now unused OOB operations and ctrl_iface
commands that had already been deprecated by the new NFC operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
The PSK generation done by pbkdf2_sha1() is one of the longest CPU time
users according to our profiling from boot to GO started.
So I have reduced some steps.
I could boot a GO by this command sequence.
-------------
add_net
set_network 0 ssid '"DIRECT-XX"'
set_network 0 psk
'"123456789012345678901234567890123456789012345678901234567890123"'
set_network 0 proto RSN
set_network 0 key_mgmt WPA-PSK
set_network 0 pairwise CCMP
set_network 0 auth_alg OPEN
set_network 0 mode 3
set_network 0 disabled 2
p2p_group_add persistent=0 freq=2412
-------------
By this sequence, pbkdf2_sha1() was called three times and the function
calculates the same value each time. Reduce number of calls to
pbkdf2_sha1() from 3 to 1 by caching the previous result.
Signed-hostap: Masashi Honma <masashi.honma at gmail.com>
This function is now unused after the last couple of commits that
removed the last uses, so remove this to keep code simpler since all
places that disassociate, can use deauthentication instead.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Even though the standard currently describes disassociation to be used
for RSN element mismatch between Beacon/Probe Response frames and
EAPOL-Key msg 3/4, this is unnecessary difference from other cases that
deauthenticate. In addition, there is no point in leaving the 802.11
Authentication in place in this case. To keep things simpler, use
deauthentication here to get rid of the only use of
wpa_sm_disassociate().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If WPS Registrar tries to provision a WPA/WPA2-Personal network without
including a valid Network Key, the network block cannot be used to
connect to the network. Reject such credential without adding the
network block. This makes wpa_supplicant send WSC_NACK as a response to
the invalid Credential and stop the provisioning process immediately
rather than only after trying unsuccessfully to connect to the network.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new P2P_SET parameter disc_int can now be used to configure
discoverable interval for p2p_find operations. The format of the command
for setting the values is "P2P_SET disc_int <minDiscoverableInterval>
<maxDiscoverableInterval> <max TUs for discoverable interval>". The
first two parameters are given in units of 100 TUs (102.4 ms). The third
parameter can be used to further limit the interval into a specific TU
amount. If it is set to -1, no such additional limitation is enforced.
It should be noted that the P2P specification describes the random
Listen state interval to be in units of 100 TUs, so setting the max TU
value to anything else than -1 is not compliant with the specification
and should not be used in normal cases. The default parameters can be
set with "P2P_SET disc_int 1 3 -1".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The old WPS interface for using NFC has no known deployments and even
the binary libraries referenced here are not easily available anymore.
Since the new interface for using NFC with WPS covers the same
functionality, remove the old implementation to clean up WPS
implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
When WPS is used with NFC connection handover, the AP may indicate its
operating channel within the credential information. Use this
informatiom, if present, to speed up the scan process.
Signed-hostap: Jouni Malinen <j@w1.fi>
This commit adds new wpa_supplicant ctrl_iface commands to allow
external programs to go through NFC connection handover mechanism
with wpa_supplicant taking care of the WPS processing. This version
includes only the case where wpa_supplicant is operating as a
station/Enrollee.
Signed-hostap: Jouni Malinen <j@w1.fi>
The previous eapol_sm_notify_cached() implementation forced the port
to be authorized when receiving EAPOL-Key msg 1/4 that included a
matching PMKID in cases when PMKSA caching is used. This is too early
since the port should really be authorized only after the PTK has been
configured which is the case when PMKSA caching is not used.
Fix this by using the EAPOL supplicant PAE state machine to go through
the AUTHENTICATING and AUTHENTICATED states instead of forcing a jump
to AUTHENTICATED without performing full state machine steps. This can
be achieved simply by marking eapSuccess TRUE at least with the current
version of EAP and EAPOL state machines (the earlier commits in this
function seemed to indicate that this may have not been that easy in
the older versions due to the hacks needed here).
This addresses an issue with nl80211-based driver interface when the
driver depends on the STA Authorized flag being used to prevent
unprotected frames from being accepted (both TX and RX) prior to PTK
configuration.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
If the driver indicates support for multi-channel concurrency, change
the p2p_connect behavior to not force the current operating channel, but
instead, just mark it as preferred for GO Negotiation. This change
applies only for the case when the freq parameter is not used with the
p2p_connect command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There was an issue with EAPOL frame exchanges in a multi-BSS
configuration when a station switches between the BSSes controlled by
the same hostapd process. When processing the EAPOL packet, the array of
virtual APs (iface->bss) is searched looking for the station that sent
the packet in order to identify which signal context should be used
during processing. The first match of the station in its list gets used
in the ieee802_1x_receive() function. However, even after a station has
disassociated, it remains in the list of stations pending an inactivity
timeout. This leads to the wrong hapd context (one where the station had
already disassociated) being used in some cases (if the current/active
bss entry appears in the list after one where the station has just
disassociated from) for EAPOL processing.
Fix this by checking the WLAN_STA_ASSOC flag before assuming the right
hapd context was found for the given station.
Signed-hostap: David Bird <dbird@powercloudsystems.com>
intended-for: hostap-1
This uses the recent cfg80211 changes to allow SAE authentication to be
implemented with the nl80211 driver interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
P2P includes two use cases where one of the devices is going to start a
group and likely change channels immediately after processing a frame.
This operation may be fast enough to make the device leave the current
channel before the peer has completed layer 2 retransmission of the
frame in case the ctrl::ack frame was lost. This can result in the peer
not getting TX status success notification.
For GO Negotiation Confirm frame, p2p_go_neg_conf_cb() has a workaround
that ignores the TX status failure and will continue with the group
formation with the assumption that the peer actually received the frame
even though we did not receive ctrl::ack. For Invitation Response frame
to re-invoke a persistent group, no such workaround is used in
p2p_invitation_resp_cb(). Consequently, TX status failure due to lost
ctrl::ack frame results in one of the peers not starting the group.
Increase the likelihood of layer 2 retransmission getting acknowledged
and ctrl::ack being received by waiting a short duration after having
processed the GO Negotiation Confirm and Invitation Response frames for
the re-invocation case. For the former, use 20 ms wait since this case
has been worked around in deployed devices. For the latter, use 50 ms
wait to get even higher likelihood of getting ctrl::ack through since
deployed devices (and the current wpa_supplicant implementation) do not
have a workaround to ignore TX status failure.
20 ms is long enough to include at least couple of retries and that
should increase likelihood of getting ctrl::ack through quite a bit. The
longer 50 ms wait is likely to include full set of layer 2 retries.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 458cb30191 broke LEAP since it
rejects EAP-Success packet that is used within LEAP and this frame does
not have a payload. Fix LEAP by relaxing the generic EAP packet
validation if LEAP has been negotiated.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, WPS Registrar allowed multiple wildcard PINs to be
configured. This can get confusing since these PINs get assigned to any
Enrollee that does not have a specific PIN and as such, cannot really be
used with different PIN values in reasonable ways. To avoid confusion
with multiple enabled PINs, invalidate any previously configured
wildcard PIN whenever adding a new one.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
While the existing code already addresses TLS Message Length validation
for both EAP-TLS peer and server side, this adds explicit checks and
rejection of invalid messages in the functions handling reassembly. This
does not change externally observable behavior in case of EAP server.
For EAP peer, this starts rejecting invalid messages instead of
addressing them by reallocating the buffer (i.e., ignoring TLS Message
Length in practice).
Signed-hostap: Jouni Malinen <j@w1.fi>
EAP-TLS/PEAP/TTLS/FAST server implementation did not validate TLS
Message Length value properly and could end up trying to store more
information into the message buffer than the allocated size if the first
fragment is longer than the indicated size. This could result in hostapd
process terminating in wpabuf length validation. Fix this by rejecting
messages that have invalid TLS Message Length value.
This would affect cases that use the internal EAP authentication server
in hostapd either directly with IEEE 802.1X or when using hostapd as a
RADIUS authentication server and when receiving an incorrectly
constructed EAP-TLS message. Cases where hostapd uses an external
authentication are not affected.
Thanks to Timo Warns for finding and reporting this issue.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
This replaces the previously used bogus test data in SAE messages with
the first real field. The actual SAE authentication mechanism is still
missing and the Scaler, Element, and Confirm fields are not included.
Signed-hostap: Jouni Malinen <j@w1.fi>
Channel frequency for 60 GHz band do not fit into 'short int', as was
used. Expand it to 'int'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These values are used with WAPI and CCX and reserving the definitions
here reduces the number of merge conflicts with repositories that
include these functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
This introduces new AKM for SAE and FT-SAE and adds the initial parts
for going through the SAE Authentication frame exchange. The actual SAE
algorithm and new fields in Authentication frames are not yet included
in this commit and will be added separately. This version is able to
complete a dummy authentication with the correct authentication
algorithm and transaction values to allow cfg80211/mac80211 drivers to
be tested (all the missing parts can be handled with
hostapd/wpa_supplicant changes).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows hostapd_cli and wpa_cli all_sta command to be used to
display connected time (in seconds) of each station in AP mode.
Signed-hostap: Raja Mani <rmani@qca.qualcomm.com>
Commit 6b56cc2d97 added clearing of the
p2p->pending_action_state too early in this function. This should not
be done if we are going to silently ignore the frame due to dialog
token mismatch. Fix this by moving the code around to check the dialog
token first.
This issue resulted in PD Request retries getting stopped too early if
the peer is sending out an unexpected PD Response (e.g., because of it
being excessively slow with the response so that the response is
received only after the next TX attempt with a new dialog token).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make Invitation process for re-invoking a persistent group behave
similarly to GO Negotiation as far as channel negotiation is concerned.
The Operating Channel value (if present) is used as a starting point if
the local device does not have a forced operating channel (e.g., due to
concurrent use). Channel lists from devices are then compared to check
that the selected channel is in the intersection. If not, channel is
selected based on GO Negotiation channel rules (best channel preferences
etc.). Invitation Request is rejected if no common channel can be
selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
As long as WLAN_STA_ASSOC_REQ_OK is set in sta->flags, Class 3 frames do
not trigger a disassoc/deauth. If it is still set even after the assoc
response tx has already failed, it may take somewhat longer for clients
to realize that the connection wasn't fully established.
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
This avoids extra latency caused by establishing an aggregation session
and makes the initial connection attempt more reliable
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
This patch fixes an issue where removing a WDS VLAN interface also
removed the main AP interface from the same bridge.
Signed-hostap: Felix Fietkau <nbd@openwrt.org>
This is a generic AES CCM implementation that can be used for other
purposes than just implementing CCMP, so it fits better in a separate
file in src/crypto.
Signed-hostap: Jouni Malinen <j@w1.fi>
Now that the internal AES implementation supports 256-bit keys, enable
use of the TLS cipher suites that use AES-256 regardless of which crypto
implementation is used.
Signed-hostap: Jouni Malinen <j@w1.fi>
AES uses the same 128-bit block size with 128, 192, 256 bit keys, so use
the fixed block size definition instead of trying to dynamically set the
block size based on key length. This fixes use of 192-bit and 256-bit
AES keys with crypto_cipher_*() API when using the internal AES
implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is otherwise identical to aes_gcm_ae() but does not use the
plain/crypt pointers since no data is encrypted.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds 192-bit and 256-bit key support to the internal AES
implementation and extends the AES-GCM functions to accept key length to
enable longer AES key use.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a generic AES GCM and GMAC implementation that can be used for
other purposes than just implementing GCMP, so it fits better in a
separate file in src/crypto.
Signed-hostap: Jouni Malinen <j@w1.fi>
The conf doesn't contain any basic rates in some cases. Most notably,
when starting a P2P GO in 5 GHz. Use the iface rates which are
initialized in hostapd_prepare_rates() to the conf rates or set to
default values if no conf values exist. This fixes a bug introduced in
commit e5693c4775.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Commit e5693c4775 added a copy of the
determined basic rate set into struct hostapd_iface, but did not
actually copy the terminating -1 value. This could be problematic if
something were to actually try to use this list since would be no way to
know what is the last entry in the list. Fix this by copying the
terminating value.
Signed-hostap: Jouni Malinen <j@w1.fi>
This driver_op can now be used in station mode, too, to fetch
information about the connection with the AP, so allow this to be used
even if wpa_supplicant is built without AP mode support.
Signed-hostap: Jouni Malinen <j@w1.fi>
The group matching should be done by comparing the P2P Interface Address
(which the group_bssid here is) to the group's BSSID and not the group
ID (which uses P2P Device Address and would have also needed the SSID).
Though, it should be noted that this case cannot really happen since a
GO in an active group would never be invited to join another group in
its GO role (i.e., if it receives an Invitation Request, it will reply
in P2P Device role). As such, this fix does not really change any
observable behavior, but anyway, it is good to keep the implementation
here consistent with the Invitation Request case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When building the Invitation Request for WFD use cases, match the BSSID,
i.e., P2P Interface Address, of the group on the GO to avoid using
information from another group should the device be operating multiple
concurrent groups as GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use the anonymous_identity field to store EAP-SIM/AKA pseudonym identity
so that this can be maintained between EAP sessions (e.g., after
wpa_supplicant restart) even if fast re-authentication data was cleared.
Signed-hostap: Jouni Malinen <j@w1.fi>
The EAP-SIM/AKA code is already validating the prefix and the following
lookup would not find matches if the prefix is incorrect, so there is no
need for the extra checks here.
Signed-hostap: Jouni Malinen <j@w1.fi>
If EAP-Response/Identity includes a known pseudonym or re-auth username,
skip the AKA/Identity exchange since we already know the permanent
username of the peer.
Signed-hostap: Jouni Malinen <j@w1.fi>
RFC 4186, chapter 6.3.3 mandates that EAP-Failure is used only after
Client-Error and Notification messages. Convert the direct jumps to the
FAILURE state with a notification round before sending out EAP-Failure.
Signed-hostap: Jouni Malinen <j@w1.fi>
The AT_NONCE_S value needs to be used in AT_MAC calculation for
SIM/Re-authentication response even if re-authentication is rejected
with AT_COUNTER_TOO_SMALL.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
If the peer rejects re-authentication with AT_COUNTER_TOO_SMALL, fall
back to full authentication to allow the authentication session to be
completed.
Signed-hostap: Jouni Malinen <j@w1.fi>
These fields are used only as the search key, so the value is already
known and does not need to be copied from the database.
Signed-hostap: Jouni Malinen <j@w1.fi>
Store permanent username (i.e., including prefix character) instead of
IMSI in the SQLite DB. Convert the string to a string since the EAP-AKA
prefix can start with zero. This cleans up the field names since the
value was already with the prefix included instead of just IMSI. In
addition, this explicitly removes some theoretical cases where the
different identity types could have been mixed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since the EAP-SIM/AKA identities are ASCII strings, there is no need to
use more complex way for storing and passing them. In addition, be more
strict about enforcing username (i.e., no realm part) to be used in the
EAP-SIM DB API. Similarly, require specific username type instead of any
of the types to be used as the key in the pseudonym and reauth
operations. This allows simpler lookup operations to be used.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we always request an identity in the request, the response
has to include AT_IDENTITY. This allows the AKA/Identity response
processing to be simplified a bit.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need to use eap_sim_db_identity_known() here since a new
AKA/Identity message is built only if the identity in the previous
response was not recognized. The first round is always used to request
AT_ANY_ID_REQ to meet the RFC 4187 recommendation on EAP method specific
identity request.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since we always request an identity in the request, the response
has to include AT_IDENTITY. This allows the SIM/Start response
processing to be simplified a bit.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need to use eap_sim_db_identity_known() here since a new
SIM/Start message is built only if the identity in the previous response
was not recognized. The first round will always request AT_ANY_ID_REQ to
meet the RFC 4186 recommendation on EAP method specific identity request
being used.
Signed-hostap: Jouni Malinen <j@w1.fi>
The reauth_id prefix can be used to determine which AKA version is used,
so there is no need to store the aka_prime information in a separate
field.
Signed-hostap: Jouni Malinen <j@w1.fi>
If hostapd is built and configured to use SQLite database, store
EAP-SIM/AKA reauth data into the database to allow this to persist
over hostapd restarts.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows hostapd to use an SQLite database for storing EAP-SIM/AKA
pseudonyms over process restarts. CONFIG_SQLITE=y build option adds
support for this and the SQLite database file is specified in eap_sib_db
configuration parameter.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Try to share most of the cipher information like key and RSC lengths and
suite selector conversions, etc. in wpa_common.c to avoid having similar
code throughout the WPA implementation for handling cipher specific
behavior.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_cli p2p_serv_disc_req command can now be used to request WSD
request to be sent to specified or all peers who support WSD.
format: wifi-display <list of roles> <list of subelements>
examples:
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source] 2,3,4,5
p2p_serv_disc_req 02:01:02:03:04:05 wifi-display [pri-sink] 3
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [sec-source] 2
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source+sink] 2,3,4,5
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source][pri-sink] 2,3,4,5
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds control interface commands and internal storage of
Wi-Fi Display related configuration. In addition, WFD IE is now added
to various P2P frames, Probe Request/Response, and (Re)Association
Request/Response frames. WFD subelements from peers are stored in the
P2P peer table.
Following control interface commands are now available:
SET wifi_display <0/1>
GET wifi_display
WFD_SUBELEM_SET <subelem> [hexdump of length+body]
WFD_SUBELEM_GET <subelem>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows both hostapd and wpa_supplicant to be used to derive and
configure keys for GCMP. This is quite similar to CCMP key
configuration, but a different cipher suite and somewhat different rules
are used in cipher selection. It should be noted that GCMP is not
included in default parameters at least for now, so explicit
pairwise/group configuration is needed to enable it. This may change in
the future to allow GCMP to be selected automatically in cases where
CCMP could have been used.
This commit does not included changes to WPS or P2P to allow GCMP to be
used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use the NL80211_IFACE_COMB_NUM_CHANNELS value > 1 as a trigger for
enabling support for P2P multichannel channel concurrency. This does not
handle all possible details of enforcing driver capabilities, but it is
a good first step for allowing nl80211 drivers to enable multichannel
concurrency.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new gas_request and gas_response_get commands can be used to request
arbitary GAS queries to be performed. These can be used with ANQP or
with other (including vendor specific) advertisement protocols.
gas_request <BSSID> <AdvProtoID> [Query]
gas_response_get <addr> <dialog token> [offset,length]
For example, ANQP query for Capability list in interactive wpa_cli
session:
> gas_request 02:00:00:00:01:00 00 000102000101
<3>GAS-RESPONSE-INFO addr=02:00:00:00:01:00 dialog_token=0
status_code=0 resp_len=32
> gas_response_get 02:00:00:00:01:00 00
01011c00010102010501070108010c01dddd0c00506f9a110200020304050607
> gas_response_get 02:00:00:00:01:00 00 0,10
01011c00010102010501
> gas_response_get 02:00:00:00:01:00 00 10,10
070108010c01dddd0c00
> gas_response_get 02:00:00:00:01:00 00 20,10
506f9a11020002030405
> gas_response_get 02:00:00:00:01:00 00 30,2
0607
It should be noted that the maximum length of the response buffer is
currently 4096 bytes which allows about 2000 bytes of the response data
to be fetched with a single gas_response_get command. If the response is
longer, it can be fetched in pieces as shown in the example above.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new vendor_elements parameter in hostapd.conf can be used to add new
vendor specific element(s) into Beacon and Probe Response frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Maintain state of WPS APs during iteration to find the correct AP for
WPS PIN operation when no specific BSSID is specified. This information
can be used for optimizing the order in which the APs are tried. This
commit is only adding the collection of the information and more
detailed debug information to make debug logs more helpful in figuring
out how the AP selection order could be improved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If 4-way handshake fails due to likely PSK failure or if EAP
authentication fails, disable the network block temporarily. Use longer
duration if multiple consecutive failures are seen.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace the Venue Name specific data structure and parser with a
generic mechanism that can be used with other fields that use the
same format.
Signed-hostap: Jouni Malinen <j@w1.fi>
The anqp_3gpp_cell_net parameter can be used to configure hostapd
to advertise 3GPP Cellular Network ANQP information.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
These function pointers are going to be the same for each interface so
there is no need to keep them in struct hostapd_iface. Moving them to
struct hapd_interfaces makes it easier to add interfaces at run time.
Signed-hostap: Jouni Malinen <j@w1.fi>
The driver_test.c data structures had been changed to use a separate
BSS structure, but the P2P commands were not using the new design.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 488f4a7108 configures a timer
before p2p_send_action(). This may result in the timer getting fired
earlier to the off channel transmission of the frame and thus another PD
request being retransmitted. This shall lead to the new PD request with
an incremented dialog token being transmitted. For the cases where the
later PD request might not be transmitted as the host driver is busy
transmitting the earlier frame, the received PD response could be
dropped for the dialog token mismatch. Remove the timer configuration to
avoid this behavior.
Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
intended-for: hostap-1
Previously, all station mode scan operations were either skipped or
delayed while any P2P operation was in progress. To make concurrent
operations easier to use, reduce this limitation by allowing a scan
operation to be completed in the middle of a p2p_find. In addition,
allow station mode association to be completed. When the station mode
operation is run to its completion (scan results not acted on,
connection to an AP completed, connection failed), resume the p2p_find
operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A new optional delay=<search delay in milliseconds> parameter can now be
used with p2p_find command to request an extra delay between search
iterations. This can be used, e.g., to make p2p_find friendlier to
concurrent operations by avoiding it from taking 100% of the radio
resources.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This EAP type uses a vendor specific expanded EAP header to encapsulate
EAP-TLS with a configuration where the EAP server does not authenticate
the EAP peer. In other words, this method includes only server
authentication. The peer is configured with only the ca_cert parameter
(similarly to other TLS-based EAP methods). This method can be used for
cases where the network provides free access to anyone, but use of RSN
with a securely derived unique PMK for each station is desired.
The expanded EAP header uses the hostapd/wpa_supplicant vendor
code 39068 and vendor type 1 to identify the UNAUTH-TLS method.
Signed-hostap: Jouni Malinen <j@w1.fi>
The previous implementation was able to re-open the connection to an
external program (e.g., hlr_auc_gw) when needed, but required the
connection to be available during startup. Extend this to allow the
initial failure, so that hlr_auc_gw can be started after hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
Explicitly validate seed_len to skip memset call with zero length of
copied data at the end of the buffer. This is not really needed, but it
makes the code a bit easier for static analyzers. This is identical to
the commit a9ea17491a but for the OpenSSL
version of the function.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit bfc62fe133 moved the code that
using crypto/random.h, but forgot to remove the inclusion of that header
file.
Signed-hostap: Jouni Malinen <j@w1.fi>
All the TNC base64 operations are within tncs.c, so there is no point in
including base64.h into eap_server_tnc.c.
Signed-hostap: Jouni Malinen <j@w1.fi>
All the other places processing EVENT_RX_MGMT events assume that the
event data is included, so not much point in verifying that here.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use an explicit pointer to the beginning of the buffer and a flag
to indicate whether that is to external data or not. This avoids
a branch whenever accessing the buffer and helps some static
analyzers to understand the wpabuf memory uses better.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the os_malloc() call for the User-Name value fails in EAP-TTLS
server, the inner MSCHAPv2 processing could have tried to dereference a
NULL pointer. Avoid this by handling this cleanly as an internal error
and reject the authentication attempt.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Commit c9e08af24f removed the only user of
the special case MD5 use that would be allowed in FIPS mode in
tls_prf_sha1_md5(). Commit 271dbf1594
removed the file from the build, but left the implementation into the
repository. To clean things up even further, remove this functionality
completely since it is not expected to be needed for FIPS mode anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows User-Name and Chargeable-User-Identity attributes to be
passed from Access-Accept into Accounting messages even when IEEE 802.1X
is not used.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
The mechanism to figure out key block size based on ssl->read_hash
does not seem to work with OpenSSL 1.0.1, so add an alternative
mechanism to figure out the NAC key size that seems to work at
least with the current OpenSSL 1.0.1 releases.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Some deployed authentication servers seem to be unable to handle the TLS
Session Ticket extension (they are supposed to ignore unrecognized TLS
extensions, but end up rejecting the ClientHello instead). As a
workaround, disable use of TLS Sesson Ticket extension for EAP-TLS,
EAP-PEAP, and EAP-TTLS (EAP-FAST uses session ticket, so any server that
supports EAP-FAST does not need this workaround).
Signed-hostap: Jouni Malinen <j@w1.fi>
tls_disable_session_ticket=1 in phase1/phase2 can now be used to disable
use of TLS Session Ticket extension (which is enabled by default in
recent OpenSSL versions). This can be used to work around issues with
broken authentication servers that do not ignore unrecognized TLS
extensions properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This can be used to implement workaround for authentication servers that
do not handle TLS extensions in ClientHello properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
The PKCS5_PBKDF2_HMAC_SHA1() function in OpenSSL 0.9.7 did not mark
the salt parameter const even though it was not modified. Hide the
compiler warning with a type cast when an old OpenSSL version is
used.
Signed-hostap: Jouni Malinen <j@w1.fi>
When CONFIG_FIPS=y is used, do not include MD5 in the build and disable
EAPOL-Key frames that use MD5 (WPA/TKIP and dynamic WEP with IEEE
802.1X).
Signed-hostap: Jouni Malinen <j@w1.fi>
