When the driver sends a CQM RSSI threshold event, wpa_supplicant queries
the driver for the signal and noise values. However, it is possible that
by that time the station has already disconnected from the AP, so these
values are no longer valid. In this case, indicate that these values are
invalid by setting them to WPA_INVALID_NOISE.
Previously a value of 0 would be reported, which may be confusing as
this is a valid value.
Since nl80211_get_link_signal() and nl80211_get_link_noise() already set
invalid values for a case of failure, just use the value set by these
functions even if they fail.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Allow to run local/remote process like:
- ubus listen
- logread -f
- tail -f
- wpa_cli
- hostapd_cli
And next wait for specific event(s).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
S1G beacons save a few bytes by not requiring the RSNE in beacon if RSN
BSS is configured. Handle this in wlantest by only clearing RSNE from
the BSS info if frame is a Probe Response frame.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Sweden now allows channel 149 in the updated wireless-regdb. Choose
Japan for the negative test instead.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Add a new hostapd configuration parameters rssi_ignore_probe_request to
ignore Probe Request frames received with too low RSSI.
Signed-off-by: John Crispin <john@phrozen.org>
Add initial_freq_list to wpa_supplicant configuration. This option
allows wpa_supplicant to scan a smaller list of frequencies when it
starts. This in turn allows for a faster connection to an already known
network. This limit applies only for the initial scan operation and does
not restrict other channels from being used in consecutive scans.
Tests have shown this to reduce the amount of time for connecting to a
network from roughly 3 seconds to roughly 0.1 second.
Signed-off-by: Frederik Juul <frederik.juul@3shape.com>
Previously hostapd would not stop transmitting when a DFS event was
detected and no available channel to switch to was available.
Disable and re-enable the interface to enter DFS state. This way, TX
does not happen until the kernel notifies hostapd about the NOP
expiring.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the ability to disable HT/VHT/HE for specific BSS from hostapd.conf.
- Add disable_11ax boolean to hostapd_bss_config.
- Change disable_11n and disable_11ac to bool in hostapd_bss_config.
- Add configuration option to set these disable_11* parameters
(which were previously used only automatically based on incompatible
security parameters to disable HT/VHT).
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Add a test which uses a DFS channel, waits for CAC afterwards successful
mesh join and then triggers a radar event and checks if the mesh comes
up again on the same device.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
The hostapd DFS code deinitializes and initializes the AP interface, if
a clean channel switch is not possible. In this case the AP code paths
would deinit the driver, for example nl80211, without wpa_supplicant
code paths getting notice of this.
Therefore add callbacks for wpa_supplicant mesh methods, which are
called on init/deinit of the AP BSS. These callbacks are then used to
handle the reset in the mesh code.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Send mesh group started notification after join completion
callback is called.
Implement outstanding TODO, to leave the mesh network on deinit.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Only change freq params, if ifmsh->freq is set initially, which only
happens if hostapd_get_hw_features in setup_interface2 succeeds.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
The kernel requires indication of DFS handler residing in user space
(NL80211_ATTR_HANDLE_DFS) to enable DFS channels.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Mesh interface would have used its channel parameters that were
configured during initialization even after channel switch due to DFS
radar detection during CAC which could result in a channel switch error.
Fix the error by updating the channel parameters when channel has been
changed from the initial one.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
mac80211 does not allow mgmt tx to use off channel on
DFS channels in non-ETSI domain, because it will invalidate
CAC result on current operating channel.
(mac80211 commit: 34373d12f3cbb74960a73431138ef619d857996f)
Hence don't set offchanok for mgmt tx in case of DFS channels
in non-ETSI.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
ssid->frequency is one of the variables used to get the channel number
from a given frequency. Leaving it as unchanged when pri/sec channel
switch will cause picking up a wrong channel number after applying the
secondary channel offset for HT40 and leads to failing interface
bring-up.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Mesh join function is the last function to be called during mesh join
process, but it's been called a bit earlier than it's supposed to be, so
that some mesh parameter values such as VHT capabilities were not
applied correct when mesh join is in process. Moreover, the current
design of mesh join that is called directly after mesh initialization
isn't suitable for DFS channels to use, since mesh join process should
be paused until DFS CAC is done and resumed after it's done.
The callback will be called by hostapd_setup_interface_complete_sync().
There is a possibility that completing mesh init fails, so add error
handling codes for that.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Define QCA vendor attributes to dynamically configure TX NSS and RX NSS
to be used with QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION commands.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the maximum operating channel width for AP/P2P GO is not specified,
it is auto-selected during configuration. While selecting the channel
width, if VHT is supported and 160 MHz channels are available, 160 MHz
channel width is preferred to 80 MHz.
During the selection of the channel width, the corresponding driver
capabilities were not checked. As a result, the AP/P2P GO configuration
was set to use the available 160 MHz channels even if the driver did not
have capability to support the 160 MHz channel width causing failure to
start the AP/P2P GO.
Fix this by checking the driver support for the 160 MHz channel width
while selecting the channel width for AP/P2P GO.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Store information on whether extra ANQP elements were received using the
protection alternative (protected GAS during an association using PMF)
and make this available through the control interface BSS command.
For example:
anqp[277]=<hexdump>
protected-anqp-info[277]=1
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
TWT nudge is a combination of suspend and resume in a single request.
Add TWT nudge operation and QCA vendor attributes to support
the TWT nudge request.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Replace the previously used design "(u8 *) (bss + 1)" with a variable
length array at the end of struct wpa_bss bss->ies[] in hopes of making
this easier to understand for static analyzers.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it easier to change the internal struct wpa_bss design for
storing the variable length IE buffers.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This removes need from the callers to know the struct wpa_bss details
for the location of the memory area for storing the IEs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Change struct dl_list pointer argument to const in list functions that
do not manipulate the list: dl_list_len() and dl_list_empty().
Signed-off-by: Hai Shalom <haishalom@google.com>
Use NL80211_ATTR_SAE_PWE attribute to indicate the sae_pwe value
to the driver during the NL80211_CMD_START_AP and NL80211_CMD_CONNECT
in WPA3-Personal networks which are using SAE authentication.
Signed-off-by: Rohan Dutta <drohan@codeaurora.org>
P2P usage in the 6 GHz band is not standardized yet by WFA. Disable P2P
operations in the 6 GHz band to avoid potential interop issues with
existing P2P devices in production. P2P operations in the 6 GHz band can
be reenabled later after defining standard ways to address potential
interop issues with existing P2P devices.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, the configuration to disable the 6 GHz band remained local
to the P2P interface. With this there is a possibility of 6 GHz channels
being included in the channel list when the channel list needs to be
updated if the state changes on one of the interfaces.
Include the configuration to disable the 6 GHz band for P2P as a global
configuration value to prevent the inclusion of 6 GHz channels in the
channel list for P2P when the channel list needs to be updated during
the state change in one of the interfaces.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
Add support to report a vendor specific connect fail reason code fetched
from the driver to users by adding the reason code to the event
CTRL-EVENT-ASSOC-REJECT. Fetch the connect fail reason code when the
driver sends a failure connection result and append the reason code, if
available, to assoc reject event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduces a vendor specific feature capability
QCA_WLAN_VENDOR_FEATURE_CONCURRENT_BAND_SESSIONS to know if the device
supports concurrent network sessions on different Wi-Fi bands. This feature
capability is attributed to the hardware's capability to support the same
(e.g., DBS).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The newer kernel versions enforce strict netlink attribute policy
validation and will cause cfg80211 to reject vendor commands with
NL80211_ATTR_VENDOR_DATA if NLA_F_NESTED attribute is not set but
if the vendor command is expecting nested data within
NL80211_ATTR_VENDOR_DATA attribute.
Most of the earlier instances were addressed by adding NLA_F_NESTED
flag in nla_nest_start(). This commit addresses the remaining
instance in which NL80211_ATTR_VENDOR_DATA is populated using data
set by user through the control interface.
Enhance the control interface VENDOR command to indicate whether the
vendor subcommand uses nested attributes within NL80211_ATTR_VENDOR_DATA
attribute or not.
Set NLA_F_NESTED flag for existing QCA vendor commands which use nested
attributes within the NL80211_ATTR_VENDOR_DATA attributes so that the
old frameworks implementations for already existing commands work
without any issues.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FULL_BW_UL_MU_MIMO to
enable/disable full bandwidth UL MU-MIMO subfield in the HE PHY
capabilities information field for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use the common IE parsing routine in hope of trying to make the length
checks easier for static analyzers. In addition, try to make the
*_vendor_ie_multi() cases easier to analyze as well even though they
cannot use for_each_element_id().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Report failures at lower layer to the upper layer D-Bus handling of
socket registration to allow failures to be addressed more cleanly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use the common IE parsing routine in hope of trying to make the length
checks easier for static analyzers.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends the changes in commit c397eff828 ("Make GTK length
validation easier to analyze") to cover the RSN case as well as the WPA.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
