There may be more than one attribute of same type (e.g., multiple DC
attributes), so the code needs to be able to handle that. Replace the
fixed structure with an array of attributes.
Previous version driver_bsd.c switches the channel in
wpa_driver_bsd_associate(). This patch changes it to use set_freq().
I have tested this patch on FreeBSD 8.0/NetBSD 5.0.2 with hostapd,
wpa_supplicant(AP) and wpa_supplicant(STA).
Add a new wpa_supplicant state: interface disabled. This can be used
to allow wpa_supplicant to be running with the network interface even
when the driver does not actually allow any radio operations (e.g.,
due to rfkill).
Allow driver_nl80211.c and driver_wext.c to start while rfkill is in
blocked state (i.e., when ifconfig up fails) and process rfkill
events to block/unblock WLAN.
Vendor-specific IEs are supposed to be in the end of the frame, so move
WMM into the end of Beacon, Probe Response, and (Re)Association Response
frames. In addition, move HT IEs to be later in (Re)Association
Response to match the correct order.
hostapd_eid_wpa() adds multiple IEs and the end result may not always be
correct. If WPA is enabled, WPA IE (vendor-specific) gets added in the
middle of the frame and not in the end. This would require a larger
change to spliut the IEs from WPA module into separate locations when
constructing Beacon and Probe Response frames. This is not yet addressed.
Commit 83935317a7 added forced
disconnection in case of 4-way handshake failures. However, it should
not have changed the case where the supplicant is requesting fallback
to full EAP authentication if the PMKID in EAPOL-Key message 1/4 is
not know. This case needs to send an EAPOL-Start frame instead of
EAPOL-Key message 2/4.
This works around a problem with APs that try to force PMKSA caching
even when the client does not include PMKID in (re)association request
frame to request it. [Bug 355]
Commit c02d52b405 removed direct calls
to the WPA authenticator, but the change here was incorrect.
EAPOL_SM_USES_WPA was supposed to be set based on sta->wpa_sm being
set, i.e., no need to check for PMKSA entries for that.
While this could potentially change EAPOL Key TX state machine behavior,
no clear problems have been identified so far. Anyway, better fix this
to get the correct flags set for EAPOL authenticator state machine.
When using WPS, we may end up here if the STA manages to re-associate
without the previous STA entry getting removed. Consequently, we need to
make sure that the WPA state machines gets initialized properly at this
point.
62477841a1 tried to address fragmentation
issues, but it did not address the case where the final EAP-TNC
message gets fragmented. Move the state update to the correct place
to address this case, too.
There are no subdirectories in any of these directories or plans
for adding ones. As such, there is no point in running the loop
that does not do anything and can cause problems with some shells.
Both the wildcard VLAN entry and the statically configured VLAN
interfaces should behave in the same way. Initializing the
full dynamic VLAN code before adding the statically configured VLAN
interfaces allows the same processing to be applied to both statically
and dynamically added VLAN interface (i.e., also the statically
configured ones will be added to a bridge).
The WPS IE was overriding the WPA/RSN IE in driver based MLME case
(hostapd_notif_assoc), but the MLME code here was not using WPS IE
correctly, i.e., it allowed the WPA/RSN IE override the operation.
The returned buffer length was hardcoded to be the prime length
which resulted in shorter results being padded in the end. However,
the results from DH code are supposed to be unpadded (and when used
with WPS, the padding is done in WPS code and it is added to the
beginning of the buffer). This fixes WPS key derivation errors
in about 1/256 of runs ("WPS: Incorrect Authenticator") when using
the internal crypto code.
This adds more details into the CTRL-EVENT-DISCONNECTED event to
make it easier to figure out which network was disconnected in some
race conditions and to what could have been the reason for
disconnection. The reason code is currently only available with
the nl80211 driver wrapper.
There is no absolute requirement for separating address allocation
into separate functions, so simplify the driver wrapper interface
to use just if_add and if_remove instead of adding the new
alloc_interface_addr() and release_interface_addr() functions.
if_add() can now indicate if the driver forced a different interface
name or address on the virtual interface.
The server may still reject authentication at this point, so better
use conditional success decision. This allows the potentially
following EAP-Failure message to be processed properly. [Bug 354]
hostapd does not implement UAPSD functionality. However, if U-APSD
functionality is implemented outside hostapd, add support to advertise
the functionality in beacon.
Signed-off-by: yogeshp@marvell.com
Instead of parsing the IEs in the callers, use the already existing
parser in wpa_ft.c to handle MDIE and FTIE from initial MD association
response. In addition, this provides more complete access to association
response IEs to FT code which will be needed to fix FT 4-way handshake
message 2/4.
ANonce, SNonce, R0KH-ID, and R1KH-ID must match with the values
used in the previous FT authentication sequence message per
IEEE Std 802.11r-2008, 11A.8.4.
This sets the FT Capability and Policy field in the MDIE to the values
received from the target AP (if available). This fixes the MDIE contents
during FT Protocol, but the correct value may not yet be used in initial
mobility domain association.
We do not have any keys set at this point so there is no point in
adding the MIC. In addition, IEEE Std 802.11r-2008, 11A.4.2
describes this frame to have MIC IE count of 0 and MIC of 0.
This removes transmission of some unnecessary Deauthentication
frames in cases where we only need to clear the local state. In
addition, this resolves issues for 802.11r FT-over-DS by allowing
authentication state to be set locally even when no actual
Authentication frame is to be transmitted.
IEEE Std 802.11r-2008, 11A.4.2 describes FT initial mobility domain
association in an RSN to include PMKR1Name in the PMKID-List field
in RSN IE in messages 2/4 and 3/4. This makes the RSN IE not be
bitwise identical with the values used in Beacon, Probe Response,
(Re)association Request frames.
The previous versions of wpa_supplicant and hostapd did not add the
PMKR1Name value in EAPOL-Key frame and did not accept it if added
(due to bitwise comparison of RSN IEs). This commit fixes the
implementation to be compliant with the standard by adding the
PMKR1Name value into EAPOL-Key messages during FT 4-Way Handshake and
by verifying that the received value matches with the value derived
locally.
This breaks interoperability with previous wpa_supplicant/hostapd
versions.
Running hostapd and wpa_supplicant on the same interface at the same
time is not expected to work, but it should not cause hostapd to crash.
Ignore station mode association events (no addr field) to avoid this.
IF WPA/RSN parameters were changed or WPA/RSN was disabled, the
WPA/RSN IE in Beacon/Probe Response frames was only update with
set_beacon(). We need to do this with set_generic_elem(), too, to
work with all driver wrappers.
Call ieee802_11_set_beacon() in addition to set_ap_wps_ie() when
processing WPS IE updates. This is needed with drivers that use
set_beacon() instead of set_ap_wps_ie() (i.e., nl80211).
Some ER implementation (e.g., some versions of Intel PROSet) seem to
use incorrect format for WLANEventMAC variable in PutWLANResponse.
Work around this by allowing various MAC address formats to be used
in this variable (debug message will be shown if the colon-deliminated
format specified in WFA WLANConfig 1.0 is not used).
This version of the MAC address parser allows number of different
string formats for the address (e.g., 00:11:22:33:44:55, 0011.2233.4455,
001122334455, 00-11-22-33-44-55). It returns the number of characters
used from the input string in case of success.
It turns out that this is needed for both FT-over-DS and FT-over-air
when using mac80211, so it looks easiest to just unconditionally
re-configure the keys after reassociation when FT is used.
This is needed to allow reassociation processing to skip 4-way handshake
when FT-over-DS is used with an AP that has a previous association state
with the STA.
This seems to be needed at least with mac80211 when a STA is using
FT-over-DS to reassociate back to the AP when the AP still has the
previous association state.
This makes the call simpler for driver wrappers since there is no need
to parse the IEs anymore before indicating association. In addition,
this allows association processing to be extended to use other IEs
in the future.
This avoids conflict with both Label and Display being included at
the same time (which would make it difficult to figure out which
PIN was actually used).
IGTK get_seqnum needs to be skipped in the same way as GTK one when
rekeying group keys. Previously, the old PN value (the one from the
previous key) was indicated and that resulted in MMIE replay detection
at the station.
This can be used to test 802.11w by sending a protected or unprotected
deauth/disassoc frame.
hostapd_cli deauth <dst addr> test=<0/1>
hostapd_cli disassoc <dst addr> test=<0/1>
test=0: unprotected
test=1: protected
Must update sm->pairwise when fetching PMK-R1 SA.
Add a workaround for drivers that cannot set keys before association
(e.g., cfg80211/mac80211): retry PTK configuration after association.
If the PTK configuration prior to association fails, allow reassociation
attempt to continue and configure PTK after association. This is a
workaround for drivers that do not allow PTK to be configured before
association (e.g., current cfg80211/mac80211).
This attribute is supposed to indicate which methods the AP supports as
an Enrollee for adding external Registrars. It was left to 0 when the
AP code did not yet support external Registrars and was forgotten when
the ER support was added.
On NetBSD 5.0.2, wpa_supplicant build results in messages below.
../src/drivers/driver_bsd.c: In function 'wpa_driver_bsd_get_ssid':
../src/drivers/driver_bsd.c:876: warning: passing argument 2 of 'bsd_get_ssid'
from incompatible pointer type
../src/drivers/driver_bsd.c:876: warning: passing argument 3 of 'bsd_get_ssid'
makes integer from pointer without a cast
../src/drivers/driver_bsd.c:876: error: too many arguments to function
'bsd_get_ssid'
../src/drivers/driver_bsd.c: In function 'wpa_driver_bsd_scan':
../src/drivers/driver_bsd.c:1125: warning: passing argument 2 of 'bsd_set_ssid'
from incompatible pointer type
../src/drivers/driver_bsd.c:1125: warning: passing argument 3 of 'bsd_set_ssid'
makes integer from pointer without a cast
../src/drivers/driver_bsd.c:1125: error: too many arguments to function
'bsd_set_ssid'
gmake: *** [../src/drivers/driver_bsd.o] Error 1
This patch solves this issue.
This is a step in adding FT support with nl80211-based drivers.
driver_nl80211.c is now registering to handle the FT Action frames
and is able to transmit FT Request frame. Received FT Action frames
are not yet indicated as driver events.
This is needed to fix PTK derivation to use correct length. Previously,
64-octet PTK may have been derived if the authenticator did not already
have a STA entry. Now, the correct pairwise cipher suite is learned when
then PMK-R1 SA is received.
This was not supposed to have duplicate value with WPA_AUTH_ALG_LEAP.
The previous version was unable to set FT as the authentication
algorithm with nl80211.
With this patch, a client gets kicked out of the last BSS it was
attached to, when it is associating to a different one.
While mac80211 does allow a station to be present on multiple bss
interfaces, this does seem to cause problems both for the stack
and for hostapd.
This patch allows the nl80211 driver to create its own per-bss context
and pass it to the drv_priv pointer of the hostapd bss state.
With this and the following patch, stations can associate to and switch
between multiple BSS interfaces of a single wiphy.
This obsoletes a few instances of passing ifname to a callback, those
can be removed in a separate patch.
It might also be useful to move more fields from the driver data to the
per-bss data structure in the future.
This patch allows wpa_supplicant to compile on Debian's kfreebsd
architectures.
Patch by Stefan Lippers-Hollmann based on work done by Petr Salinger
and Emmanuel Bouthenot for 0.6.X (http://bugs.debian.org/480572).
filter_ssids=1 global configuration parameter can now be used to
enable scan result filtering (with -Dnl80211 only for now) based on
the configured SSIDs. In other words, only the scan results that have
an SSID matching with one of the configured networks are included in the
BSS table. This can be used to reduce memory needs in environments that
have huge number of APs.
wpa_supplicant can now be notified of suspend/resume events, e.g.,
from pm-action scripts. This allows wpa_supplicant to clear information
that may become invalid during a suspend operation.
The kernel side support for this was just added into
wireless-testing.git. This commit adds the driver wrapper code needed
to allow wpa_supplicant to use the new functionality.
Some drivers may need to use a specific ifname for the virtual
interface, so allow them to do this with a new parameter passed
to the alloc_interface_addr() handler.
TNC IF-T is somewhat unclear on this are, but
draft-hanna-nea-pt-eap-00.txt, which is supposed to define the same
protocol, is clearer on the Flags field being included.
This change breaks interoperability with the old implementation if
EAP-TNC fragmentation is used. The old version would not accept
the acknowledgement message with the added Flags octet while the
new version accepts messagss with with both options.
If the last message from the EAP-TNC server was fragmented, the
fragment processing lost the DONE/FAIL state and did not know how
to handle the final ACK from the peer. Fix this by remembering the
earlier DONE/FAIL state when fragmenting a frame.
TNC IF-T specification is unclear on the exact contents of the fragment
acknowledgement frame. An interoperability issue with the tncs@fhh
implementation was reported by Arne Welzel
<arne.welzel@stud.fh-hannover.de> due to the different interpretations
of the specification. Relax EAP-TNC server/peer validation rules to
accept fragmentation acknowledgement frames to include the Flags field
to avoid this issue.
This patch aggregates ioctls.
First is SIOCS80211. The SIOCS80211's arguments has 3 couples.
1-1. i_len, i_data
1-2. i_val
1-3. i_len, i_data, i_val (currently only IEEE80211_IOC_APPIE)
There were 3 routines for each cases. This patch aggregates these to
one.
Second is SIOCG80211. The SIOCG80211 returns 2 type of value.
2-1. i_len
2-2. i_val
There were 2 routines for each cases. This patch aggregates these to
one.
I have tested on both FreeBSD 8.0 and NetBSD 5.0.1 with these cases.
[hostapd]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(STA)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(AP)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
This patch enables FreeBSD channel control.
I have tested on FreeBSD 7.2 with these cases.
[hostapd]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(STA)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(AP)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
The attached patch unifies hostapd wpa_driver_bsd_ops and
wpa_supplicant wpa_driver_bsd_ops.
I have tested on NetBSD 5.0.1 with these cases.
[hostapd]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(STA)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(AP)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
This patch modifies field name of struct bsd_driver_data to use
same name of struct wpa_driver_bsd_data. This is a preparation of
unifying struct bsd_driver_data and struct wpa_driver_bsd_data.
This allows external programs (e.g., UI) to get more information
about server certificate chain used during TLS handshake. This can
be used both to automatically probe the authentication server to
figure out most likely network configuration and to get information
about reasons for failed authentications.
The follow new control interface events are used for this:
CTRL-EVENT-EAP-PEER-CERT
CTRL-EVENT-EAP-TLS-CERT-ERROR
In addition, there is now an option for matching the server certificate
instead of the full certificate chain for cases where a trusted CA is
not configured or even known. This can be used, e.g., by first probing
the network and learning the server certificate hash based on the new
events and then adding a network configuration with the server
certificate hash after user have accepted it. Future connections will
then be allowed as long as the same server certificate is used.
Authentication server probing can be done, e.g., with following
configuration options:
eap=TTLS PEAP TLS
identity=""
ca_cert="probe://"
Example set of control events for this:
CTRL-EVENT-EAP-STARTED EAP authentication started
CTRL-EVENT-EAP-PROPOSED-METHOD vendor=0 method=21
CTRL-EVENT-EAP-METHOD EAP vendor 0 method 21 (TTLS) selected
CTRL-EVENT-EAP-PEER-CERT depth=0 subject='/C=US/ST=California/L=San Francisco/CN=Server/emailAddress=server@kir.nu' hash=5a1bc1296205e6fdbe3979728efe3920798885c1c4590b5f90f43222d239ca6a
CTRL-EVENT-EAP-TLS-CERT-ERROR reason=8 depth=0 subject='/C=US/ST=California/L=San Francisco/CN=Server/emailAddress=server@kir.nu' err='Server certificate chain probe'
CTRL-EVENT-EAP-FAILURE EAP authentication failed
Server certificate matching is configured with ca_cert, e.g.:
ca_cert="hash://server/sha256/5a1bc1296205e6fdbe3979728efe3920798885c1c4590b5f90f43222d239ca6a"
This functionality is currently available only with OpenSSL. Other
TLS libraries (including internal implementation) may be added in
the future.
The previous version could end leaking memory since os_free() was used
instead of wpabuf_free(). In addition, this could potentially have
triggered a crash if the TLS context were being freed when pending
input data where still in the buffer (though, this may not be possible
to trigger in practice).
The bsd_send_eapol() adds Ethernet header by itself. This patch changes it
to use l2_packet functionality.
I have tested on NetBSD 5.0.1 with WPA-PSK(TKIP).
On NetBSD, we should configure some parameters manually out of hostapd
like below.
ifconfig ath0 mediaopt hostap
ifconfig ath0 mode 11g
ifconfig ath0 chan 6
This patch does these automatically. Maybe there will be some
objections, like "hardware configuration is not hostapd/wpa_supplican's
work". So I will write the reasons why I made this patch.
1. For usability.
2. The first command fails when previous state is adhoc. This patch is
free from previous state.
3. Some driver wrappers configure these automatically (like nl80211).
4. I have wasted time trying to find out these command were needed :(
The ps3 wireless kernel driver has wireless extension support.
There is a legacy wpa_supplicant driver, and support for this
has been removed from the kernel driver, as no distributions
are using it.
This may help in debugging why cfg80211 refused the association
command since the scan results should include information about all
pending authentication and association states.
cfg80211 has a limit on pending authentications, so we better clear
the entries that we do not care about to avoid hitting the limit
when roaming between multiple APs.
This patch moves the authentication server setup before
IEEE 802.1X initialization. It's because 802.1X already
needs to have a valid SSL context.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
This allows the driver wrappers to return two sets of IEs, so that
the BSS code can use information from both Beacon and Probe Response
frames if needed. For example, some Cisco APs seem to include more
information in Wireless Provisioning Services IE when it is in the
Beacon frame.
This makes the bridge parameter unnecessary for cases where the interface
is already in a bridge and sysfs is mounted to /sys so that the detection
code works.
For nl80211, the bridge parameter can be used to request the AP
interface to be added to the bridge automatically (brctl may refuse to
do this before hostapd has been started to change the interface mode).
If needed, the bridge interface is also created.
If the driver is detected to use cfg80211, we can rely on it being able
to disconnect with SIOCSIWMLME commands and to use empty SSID as a way
to stop it from associating when we are in progress of configuring the
driver for association. Consequently, we can remove the hack that uses
random 32-octet SSID to force disconnection and re-order association
commands to match the expectations that cfg80211 has for WEXT ioctls.
This gets rid of extra scan rounds and attempts to associate with the
silly 32-octet SSID.
Better make sure the eloop_timeout data gets fully initialized. The
current code is filling in all the fields, but it is clearer to just
zero the buffer to make sure any new field added to the structure gets
initialized.
This avoids potential use of uninitialized stack memory when printing
out peer address based on SMK error message that does not include the
MAC address.
wpa_sm_step() could theoretically free the statemachine, but it does
not do it in this particular case. Anyway, the code can be cleaned to
verify whether the state machine data is still available after the
wpa_sm_step() call.
