When generating the UUID based on MAC address, share the same UUID
with all interfaces. This fixes a potential issue with concurrent
dualband APs where the UUID needs to be same for PBC to work properly.
If the msg->device_name buffer is filled from two different sources,
the copy from the P2P Device Info attribute needs to make sure that
the values gets null terminated to match the length of the correct
string should the other place use another string (which is not really
allowed by the spec, but could happen).
A new ctrl_interface command, WPS_CANCEL, can now be used to cancel
a pending or ongoing WPS operation. For now, this is only available
with wpa_supplicant (either in station or AP mode). Similar
functionality should be added for hostapd, too.
If an authorized (p2p_connect used locally) GO Negotiation is
rejected when receiving GO Negotiation Request from the peer,
indicate the failure with a ctrl_interface P2P-GO-NEG-FAILURE
event. Previously, this event was only shown on the peer (i.e.,
the device receiving the GO Negotiation Response with non-zero
Status code).
Since this message now includes P2P Device Info attribute, it is
reasonable to learn the peer data and process the message instead of
rejecting the message.
Add (or complete Probe Request only) P2P peer entry when receiving
Provision Discovery Request from a previously unknown peer. This is
especially of use for a GO when a P2P client is requesting to join
a running group.
The scan operation before Provision Discovery Request may not include
the GO. However, we are likely to have the GO in our P2P peer table,
so use that information to figure out the operating channel if BSS
table entry is not available.
This should not really happen, but it looks like the Listen command
may fail is something else (e.g., a scan) was running at an
inconvenient time. As a workaround, allow new Extended Listen
operation to be started if this state is detected.
The previous version had a bug that could result in NULL pointer
dereference if the P2P IE included Manageability attribute, but no
Capability attribute.
This can happen, e.g., when a P2P client connects to a P2P group
using the infrastructure WLAN interface instead of P2P group
interface. In that case, the P2P client may behave as if the GO
would be a P2P Manager WLAN AP.
This is needed to be able to change parameters for dynamically
created interfaces between the creation of the interface and
association/start AP commands.
Following ctrl_interface commands can now be used:
P2P_SET client_apsd disable
- disable configuration (i.e., use driver default) in client mode
P2P_SET client_apsd <BE>,<BK>,<VI>,<VO>;<max SP Length>
- enable UASPD with specific trigger configuration (0/1) per AC
(max SP Length is currently ignored)
P2P_SET go_apsd disable
- disable configuration (i.e., use driver default) in AP mode
P2P_SET go_apsd <0/1>
- disable/enable APSD in AP mode
P2P specification v1.15 fixed the description of the GAS fragmentation
to not duplicate NQP Query Response Field header in all fragments. This
change makes the fragmentation match with the description in IEEE
802.11u. The change is not backwards compatible with previous P2P
specification versions as far as fragmented SD responses are concerned.
This event indicates the Device Password ID that the peer tried
to use in GO Negotiation. For example:
P2P-GO-NEG-REQUEST 02:40:61:c2:f3:b7 dev_passwd_id=4
If enabled, cross connection allows GO to forward IPv4 packets
using masquerading NAT from the P2P clients in the group to an
uplink WLAN connection. This is disabled by default and can be
enabled with "wpa_cli p2p_set cross_connect 1" on the P2P device
interface.
When we receive Device Discoverability Response, we need to initiate
new GO Negotiation as quickly as possible to avoid the target client
from going back to sleep. Make sure we do not end up in
P2P_CONNECT_LISTEN state (short Listen mode) in this case.
For now, this applies to the test command that can be used to set
periodic NoA (p2p_set noa). The value are stored and periodic NoA
is enabled whenever there are no non-P2P STAs connected to the GO.
While this is not strictly speaking required by the P2P specification
for a not-P2P Managed Device, this can provide useful information for
the P2P manager AP and may be needed to pass certification tests.
While there is no real value in this, the spec seems to mark this
attribute as mandatory from GO, so better included it regardless
of whether we have clients or not (the attribute is empty in case
no clients are connected).
"wpa_cli p2p_set peer_filter <MAC address>" can now be used to
only allow a single P2P Device (based on P2P Device Address) to be
discovered for testing. Setting the address to 00:00:00:00:00:00
disables the filter.
