The P2P-FIND-STOPPED event was sent only in the P2P_SEARCH state, but
this needs to be send also in the new continue-search-when-ready states
P2P_CONTINUE_SEARCH_WHEN_READY and P2P_SEARCH_WHEN_READY for consistent
behavior.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Signal the start of EAP authentication as well as when additional
credentials are required to complete.
Signed-hostap: Paul Stewart <pstew@chromium.org>
This was previously included only with NL80211_CMD_ASSOCIATE, but the
information is as useful (if not even more useful) for
NL80211_CMD_CONNECT. It should be noted that cfg80211 does not yet use
this attribute with NL80211_CMD_CONNECT, but that can be added easily.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Each GO Negotiation Request is (re)tried with an unique dialog token and
a GO Negotiation Response / Confirmation from the peer with a mismatched
dialog token is ignored which could result in a failure in this group
formation attempt. Thus, the P2P device would continue retrying the GO
Negotiation Request frames till the GO Negotiation Response frame with a
matching dialog token is received. To avoid the failures due to the
dialog token mismatch in retry cases if the peer is too slow to reply
within the timeout, the same dialog token value is used for every retry
in the same group formation handshake.
It should be noted that this can result in different contents of the GO
Negotiation Request frame being sent with the same dialog token value
since the tie breaker bit in GO Intent is still toggled for each
attempt. The specification is not very clear on what would be the
correct behavior here. Tie breaker bit is not updated on
"retransmissions", but that is more likely referring to the layer 2
retransmission and not the retry at higher layer using a new MMPDU.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows even more memory to be freed when the SAE instance enters
Accepted state. This leaves only the minimal needed memory allocated
during the association which is especially helpful for the AP
implementation where multiple stations may be associated concurrently.
Signed-hostap: Jouni Malinen <j@w1.fi>
Most of the variables are not needed anymore once the SAE instance
has entered Accepted state. Free these to save memory.
Signed-hostap: Jouni Malinen <j@w1.fi>
The rand/mask values and commit scalar are derived using the exact same
operations, so only use a separate function for deriving the commit
element.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need to postpone this validation step to a separate
processing operation for the commit message, so move the minimal
validation tasks into the parsing functions.
Signed-hostap: Jouni Malinen <j@w1.fi>
Move the bignum comparison part into the bignum library to allow a
single implementation of rand generation for both ECC and FCC based
groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
The groups 22, 23, and 24 are not based on a safe prime and generate a
prime order subgroup. As such, struct dh_group is also extended to
include the order for previously defined groups (q=(p-1)/2 since these
were based on a safe prime).
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows FFC groups to be used with SAE. Though, these groups are not
included in the default sae_groups value based on what is available
since the FFC groups have the additional requirement of using a safe
prime with the current implementation (or specification of the group
order).
Signed-hostap: Jouni Malinen <j@w1.fi>
The optional "reason=<reason code>" parameter to the ctrl_iface
deauthenticate and disassociate commands can now be used to change the
reason code used in the disconnection frame. This can be used, e.g., by
P2P GO to disconnect a single P2P client from the group by sending it an
indication of the group getting terminated (Deauthentication frame with
reason code 3). It needs to be noted that the peer device is still in
possession on the PSK, so it can still reconnect to the group after this
if it does not follow the group termination indication.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit increases the maximum buffer size for P2P Client Info
advertized by the Group Owner in the Probe Response frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use of two variables to track bounds checking seems to be a bit too much
for some static analyzers, so add an extra condition for buffer padding
to avoid incorrect warnings.
Signed-hostap: Jouni Malinen <j@w1.fi>
These verify that a proper pointer type is used and in addition, seems
to get rid of some false static analyzer warnings.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even though this command is very unlikely to fail, in theory, it could
and the WPS connection would fail in such a case. Return more clearer
failure indication in such a case without even trying to start
reassociation.
Signed-hostap: Jouni Malinen <j@w1.fi>
The code initializing GMK Counter uses the group pointer value as extra
entropy and to distinguish different group instances. Some static
analyzers complain about the sizeof(pointer) with memcpy, so use a more
explicit type casting to make it more obvious what the code is doing.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new "sae_group=<id>" line will be included in the ctrl_iface STATUS
output if SAE was used for the association.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd.conf sae_groups parameter can now be used to limit the set of
groups that the AP allows for SAE. Similarly, sae_groups parameter is
wpa_supplicant.conf can be used to set the preferred order of groups. By
default, all implemented groups are enabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
