This allows external applications to get event indication for Probe
Request frames. Extend ctrl iface cmd "ATTACH" to enable this event on
per-request basis. For example, user has to send ctrl iface cmd "ATTACH
probe_rx_events=1" to enable the Probe Request frame events.
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
The new conf={sta,ap}-{sae,psk-sae} parameter values can now be used to
specify that the legacy configuration object is for SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows DPP to be used for enrolling credentials for SAE networks in
addition to the legacy PSK (WPA-PSK) case. In addition, enable FT-PSK
and FT-SAE cases automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to allow more invalid attribute values to be written
into Peer Discovery Request/Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the build include SHA384, use that to derive GTK from GMK. In
addition, add more random bytes bytes to the PRF-X() context data for
longer GTK to reduce dependency on the randomness of the GMK.
GMK is 256 bits of random data and it was used with SHA256, so the
previous design was likely sufficient for all needs even with 128 bits
of additional randomness in GTK derivation. Anyway, adding up to 256
bits of new randomness and using SHA384 can be helpful extra protection
particularly for the cases using GCMP-256 or CCMP-256 as the group
cipher.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter group_cipher can now be used to
override the automatic cipher selection based on enabled pairwise
ciphers. It should be noted that selecting an unexpected group cipher
can result in interoperability issues and this new capability is mainly
for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this command stopped listen operation immediately, but if
there was an ongoing authentication exchange, a new listen operation was
started. This is not really expected behavior, so stop the
authentication exchange first with this command to avoid restarting
listen operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new role=either parameter can now be used with DPP_AUTH_INIT to
indicate that the initiator can take either the Configurator or Enrollee
role.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant to iterate over all available channels from
the intersection of what the peer indicates and the local device
supports when initiating DPP Authentication. In addition, retry DPP
Authentication Request frame up to five times if no response is
received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is an initial step in allowing non-operating channel operations
with DPP when hostapd is the Responder. For now, this is only used for
specifying role=configurator/enrollee and qr=mutual cases similarly to
the wpa_supplicant configuration for in Responder role. Request to use a
non-operating channel will be rejected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add limit on number of failed attempts that could have used PKEX code.
If the limit (5) is reached, drop the PKEX state (including the code)
and report this on the control interface to indicate that a new code
needs to be entered due to possible attack.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Clean up the pending PKEX exchange if Commit-Reveal Request processing
indicates a mismatch in the PKEX code. Previously, the this case was
silently ignored and the session was left in pending state that
prevented new PKEX exchanges from getting initated. Now, a new attempt
is allowed to be initiated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Report mismatching finite cyclic group with PKEX Exchange Response using
STATUS_BAD_GROUP and provide more detailed error report over the control
interface on the peer device when this happens.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previously used WLAN_REASON_MICHAEL_MIC_FAILURE (14) value as a
response to Authentication frame or (Re)Association Request frame is not
correct since the resp value is encoded in the Status Code (not Reason
Code) field. Status Code 14 is WLAN_STATUS_UNKNOWN_AUTH_TRANSACTION
which is really what this value would have meant in the response frames.
There is no Michael MIC failure status code, so have to use the generic
"Unspecified failure" (1) reason code for these cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Indicate to upper layers if PKEX Commit-Reveal Request frame AES-SIV
decryption fails. That is a likely sign of the PKEX code mismatch
between the devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Build breakage was introduced by commit
d8afdb210e ('Allow EAPOL-Key messages 1/4
and 3/4 to be retransmitted for testing') for some
CONFIG_TESTING_OPTIONS=y builds without CONFIG_IEEE80211W=y.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
This provides access to the Minimum/Maximum Transmit Power Capabilitie
fileds (the nominal minimum/maximum transmit power with which the STA
is capable of transmitting in the current channel; signed integer in
units of decibels relative to 1 mW).
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
Handle OWE DH exchange and key setup when processing the association
event from a driver that implements AP SME.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While most places using this should be for cases where the hw_features
functionality is required, there seem to be some paths that are getting
exposed in new OWE related operations where that might not be the case.
Add explicit NULL pointer checks to avoid dereferencing the pointer if
it is not set when operating with driver wrappers that do not provide
sufficient information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Normally, WNM-Sleep Mode exit with management frame protection
negotiated would result in the current GTK/IGTK getting added into the
WNM-Sleep Mode Response frame. Some station implementations may have a
vulnerability that results in GTK/IGTK reinstallation based on this
frame being replayed. Add a new hostapd configuration parameter that can
be used to disable that behavior and use EAPOL-Key frames for GTK/IGTK
update instead. This would likely be only used with
wpa_disable_eapol_key_retries=1 that enables a workaround for similar
issues with EAPOL-Key. This is related to station side vulnerabilities
CVE-2017-13087 and CVE-2017-13088. To enable this AP-side workaround,
set wnm_sleep_mode_no_keys=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
When strict group rekeying is in effect, every station that leaves will
cause a rekeying to happen 0.5 s after leaving. However, if a lot of
stations join/leave, the previous code could postpone this rekeying
forever, since it always re-registers the handling with a 0.5 s timeout.
Use eloop_deplete_timeout() to address that, only registering the
timeout from scratch if it wasn't pending.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to test the WoWLAN GTK rekeying KRACK mitigation, add a
REKEY_GTK hostapd control interface command that can be used at certain
points of the test.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the Initiator to request a different channel to be used for DPP
Authentication and DPP Configuration exchanges. This commit adds support
for this in wpa_supplicant with the optional neg_freq=<freq in MHz>
parameter in DPP_AUTH_INIT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Both the DPP-TX and DPP-TX-STATUS events are provided.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that dpp_check_attrs() takes care of verifying that no attributes
are after the Wrapped Data attribute, the duplicated checks in hostapd
and wpa_supplicant side of the implementation can be removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Build breakage was introduced by commit
16579769ff ('Add testing functionality for
resetting PN/IPN for configured keys') for some CONFIG_TESTING_OPTIONS=y
builds.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The hostapd bss_transition parameter was previously used to control
advertisement of BSS Transition Management support, but it was not used
when processing BSS Transition Management Query/Response frames. Add an
explicit check during frame processing as well so that any misbehaving
station is ignored. In addition to bss_transition=1, allow mbo=1 to be
used to mark the functionality enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The hostapd wnm_sleep_mode parameter was previously used to control
advertisement of WNM-Sleep Mode support, but it was not used when
processing a request to use WNM-Sleep Mode. Add an explicit check during
request processing as well so that any misbehaving station is ignored.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows hostapd testing functionality to be forced to send out a
plaintext EAPOL-Key frame with the RESEND_* command. That can be useful
in seeing how the station behaves if an unencrypted EAPOL frame is
received when TK is already configured.
This is not really perfect since there is no convenient way of sending
out a single unencrypted frame in the current nl80211 design. The
monitor interface could likely still do this, but that's not really
supposed to be used anymore. For now, clear and restore TK during this
operation. The restore part is not really working correctly, though,
since it ends up clearing the TSC value on the AP side and that shows up
as replay protection issues on the station. Anyway, this is sufficient
to generate sniffer captures to analyze station behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a new hostapd configuration parameter
wpa_disable_eapol_key_retries=1 that can be used to disable
retransmission of EAPOL-Key frames that are used to install
keys (EAPOL-Key message 3/4 and group message 1/2). This is
similar to setting wpa_group_update_count=1 and
wpa_pairwise_update_count=1, but with no impact to message 1/4
retries and with extended timeout for messages 4/4 and group
message 2/2 to avoid causing issues with stations that may use
aggressive power saving have very long time in replying to the
EAPOL-Key messages.
This option can be used to work around key reinstallation attacks
on the station (supplicant) side in cases those station devices
cannot be updated for some reason. By removing the
retransmissions the attacker cannot cause key reinstallation with
a delayed frame transmission. This is related to the station side
vulnerabilities CVE-2017-13077, CVE-2017-13078, CVE-2017-13079,
CVE-2017-13080, and CVE-2017-13081.
This workaround might cause interoperability issues and reduced
robustness of key negotiation especially in environments with
heavy traffic load due to the number of attempts to perform the
key exchange is reduced significantly. As such, this workaround
is disabled by default (unless overridden in build
configuration). To enable this, set the parameter to 1.
It is also possible to enable this in the build by default by
adding the following to the build configuration:
CFLAGS += -DDEFAULT_WPA_DISABLE_EAPOL_KEY_RETRIES=1
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface commands "RESEND_M1 <addr>" and
"RESEND_M3 <addr>" can be used to request a retransmission of the 4-Way
Handshake messages 1/4 and 3/4 witht he same or modified ANonce (in M1).
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface command "RESEND_GROUP_M1 <addr>" can
be used to request a retransmission of the Group Key Handshake message
1/2 for the current GTK.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation ended up starting a new EAPOL-Key 4-way
handshake if the STA were to attempt to perform another association.
This resulted in immediate disconnection since the PTK was not ready for
configuring FILS TK at the point when EAPOL-Key msg 1/4 is sent out.
This is better than alloing the association to continue with the same TK
reconfigured, but not really ideal.
Address this potential sequence by not starting a new 4-way handshake on
the additional association attempt. Instead, allow the association to
complete, but do so without reconfiguring the TK to avoid potential
issues with PN reuse with the same TK.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows ext_mgmt_frame_handling=1 cases with hostapd to process TX
status events based on external processing. This is useful for increased
test coverage of management frame processing.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Authenticator state machine path for PTK rekeying ended up bypassing
the AUTHENTICATION2 state where a new ANonce is generated when going
directly to the PTKSTART state since there is no need to try to
determine the PMK again in such a case. This is far from ideal since the
new PTK would depend on a new nonce only from the supplicant.
Fix this by generating a new ANonce when moving to the PTKSTART state
for the purpose of starting new 4-way handshake to rekey PTK.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not reinstall TK to the driver during Reassociation Response frame
processing if the first attempt of setting the TK succeeded. This avoids
issues related to clearing the TX/RX PN that could result in reusing
same PN values for transmitted frames (e.g., due to CCM nonce reuse and
also hitting replay protection on the receiver) and accepting replayed
frames on RX side.
This issue was introduced by the commit
0e84c25434 ('FT: Fix PTK configuration in
authenticator') which allowed wpa_ft_install_ptk() to be called multiple
times with the same PTK. While the second configuration attempt is
needed with some drivers, it must be done only if the first attempt
failed.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
The new sae_password hostapd configuration parameter can now be used to
set the SAE password instead of the previously used wpa_passphrase
parameter. This allows shorter than 8 characters and longer than 63
characters long passwords to be used. In addition, this makes it
possible to configure a BSS with both WPA-PSK and SAE enabled to use
different passphrase/password based on which AKM is selected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd configuration parameter owe_groups can be used to
specify a subset of the allowed DH groups as a space separated list of
group identifiers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This additional field was added to DPP Public Action frames in DPP tech
spec v0.2.3 to support cryptographic agility in the future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The owe_transition_bssid and owe_transition_ssid parameters can now be
replace with owe_transition_ifname to clone the BSSID/SSID information
automatically in case the same hostapd process manages both the OWE and
open BSS for transition mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends OWE support in hostapd to allow DH groups 20 and 21 to be
used in addition to the mandatory group 19 (NIST P-256).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is not normally done in RSN, but RFC 8110 seems to imply that AP
has to include OWE AKM in the RSNE within these frames. So, add the RSNE
to (Re)Association Response frames when OWE is being negotiated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new owe_transition_bssid and owe_transition_ssid parameters can be
used to configure hostapd to advertise the OWE Transition Mode element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Replace vendor-specific elements for HE capabilities and HE operation
elements with the P802.11ax defined element values. This version is
based on P802.11ax/D1.4.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These allow external programs to fetch the TX and RX rate information
and signal strength for a specific STA through the hostapd control
interface command "STA <addr>". The values of these attributes are
filled in the response of nl80211 command NL80211_CMD_GET_STATION.
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
In fils_hlp_finish_assoc() the station is already added to the
driver so it is not needed to check the 'added_unassociated'
flag.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add checking for NULL req_ies when FILS processing a driver ASSOC event
in hostapd_notif_assoc(). This was already done in number of old code
paths, but the newer FILS path did not handle this. Though, it is
unlikely that this code path would be reachable in practice since this
is all within sta->auth_alg == WLAN_AUTH_FILS_* check.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new psk=<hexdump> can be used as an alternative to pass=<passphrase>
when configuring the DPP Configurator with a legacy network parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These control interface event messages can be used to allow hostapd AP
to be configured for legacy WPA2-Personal configuration with DPP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While the Suite B AKM is not really going to be used with CCMP-128 or
GCMP-128 cipher, this corner case could be fixed if it is useful for
some testing purposes. Allow that special case to skip the HMAC-SHA1
check based on CCMP/GCMP cipher and use the following AKM-defined check
instead.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This part is missing from IEEE Std 802.11ai-2016, but the lack of DHss
here means there would not be proper PFS for the case where PMKSA
caching is used with FILS SK+PFS authentication. This was not really the
intent of the FILS design and that issue was fixed during REVmd work
with the changes proposed in
https://mentor.ieee.org/802.11/dcn/17/11-17-0906-04-000m-fils-fixes.docx
that add DHss into FILS-Key-Data (and PTK, in practice) derivation for
the PMKSA caching case so that a unique ICK, KEK, and TK are derived
even when using the same PMK.
Note: This is not backwards compatible, i.e., this breaks PMKSA caching
with FILS SK+PFS if only STA or AP side implementation is updated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11ai-2016 had missed a change in the Pairwise key hierarchy
clause (12.7.1.3 in IEEE Std 802.11-2016) and due to that, the previous
implementation ended up using HMAC-SHA-1 -based PMKID derivation. This
was not really the intent of the FILS design and that issue was fixed
during REVmd work with the changes proposed in
https://mentor.ieee.org/802.11/dcn/17/11-17-0906-04-000m-fils-fixes.docx
that change FILS cases to use HMAC-SHA-256 and HMAC-SHA-384 based on the
negotiated AKM.
Update the implementation to match the new design. This changes the
rsn_pmkid() function to take in the more generic AKMP identifier instead
of a boolean identifying whether SHA256 is used.
Note: This is not backwards compatible, i.e., this breaks PMKSA caching
based on the initial ERP key hierarchy setup if only STA or AP side
implementation is updated. PMKSA caching based on FILS authentication
exchange is not impacted by this, though.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The "FILS: No pending HLP DHCP exchange with hw_addr" debug message was
missing a space before the following MAC address, so add that there to
make the message more readable.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new sae_commit_override=<hexdump> parameter can be used to force
hostapd to override SAE commit message fields for testing purposes. This
is included only in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow hostapd to be configured to perform SAE reflection attack for SAE
testing purposes with sae_reflection_attack=1 configuration parameter.
This is included only in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add PMKID into EAPOL-Key 1/4 when using SAE and fix the PMK-from-PMKSA
selection in some cases where PSK (from passphrase) could have been
used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DPP tech spec changed the contents of these frames by replacing the
public key hash attributes with a Transaction ID attribute that gets
copied from the request to the response to identify the transaction in a
simpler manner.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, CONFIG_WNM enabled build that supports WNM for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode WNM is required and there is no need for AP mode WNM.
Add support to differentiate between station mode WNM and AP mode
WNM in wpa_supplicant builds by adding CONFIG_WNM_AP that should be
used when AP mode WNM support is required in addition to station mode
WNM. This allows binary size to be reduced for builds that require
only the station side WNM functionality.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add OCE IE in Beacon, Probe Response, and (Re)Association Response
frames if OCE is enabled in the configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In case of incorrect HT40 configuration as part of an attempt to create
a 80 MHz AP, iface->conf->vht_oper_centr_freq_seg0_idx and
iface->conf->vht_oper_centr_freq_seg1_idx are zero'ed, but
iface->conf->vht_oper_chwidth remains VHT_CHANWIDTH_80MHZ. This causes
the logic in dfs_get_start_chan_idx to fail.
Fix this by setting iface->conf->vht_oper_chwidth to
VHT_CHANWIDTH_USE_HT when zero'ing the center frequency parameters.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
dpp.h file requires openssl in order to compile, which breaks
compilation on systems without it.
Move DPP_OUI_TYPE to ieee802_11_defs.h and don't include dpp.h when
not really needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
hostapd did not add a new PMKSA cache entry when FILS shared key
authentication was used, i.e., only the initial full authentication
resulted in a PMKSA cache entry being created. Derive the PMKID for the
ERP case as well and add a PMKSA cache entry if the ERP exchange
succeeds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The EAP message included in FILS Wrapped Data from the non-AP STA to the
AP is EAP-Initiate/Re-auth.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the hostapd control interface to support the
DPP_BOOTSTRAP_INFO command that was recently added for wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The default value for GTK rekeying period was previously hardcoded to
600 seconds for all cases. Leave that short value only for TKIP as group
cipher while moving to the IEEE 802.11 default value of 86400 seconds
(once-per-day) for CCMP/GCMP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This updates the previously copied implementation to be up-to-date with
the more recent wpa_supplicant changes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow hostapd to initiate and respond with PKEX bootstrapping similarly
to how this was implemented in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend hostapd configuration to include parameters needed for the DPP
AKM: dpp_connector, dpp_netaccesskey, dpp_netaccesskey_expiry,
dpp_csign, dpp_csign_expiry.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external programs to generate and add PMKSA cache entries
into hostapd. The main use for this is to run external DPP processing
(network introduction) and testing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds DPP bootstrapping, authentication, and configuration into
hostapd similarly to how the design was integrated in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd processes a received 20/40 BSS Coexistence management frame, but
if no separate callbacks are registered for handling Public Action
frames it eventually sends a reply with MSB of category code set to 1
thinking that the received frame is an invalid frame. This could happen
based on whether hostapd was built and enabled with functionality using
the callback functions.
Fix this by explicitly returning 1 from the function when the 20/40 BSS
Coexistence Management frame is processed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new acs_exclude_dfs=1 parameter can be used to request hostapd to
exclude all DFS channels from ACS consideration. This is mainly of use
for cases where the driver supports DFS channels, but for some reason a
non-DFS channel is desired when using automatic channel selection.
Previously, the chanlist parameter could have been used for this, but
that required listing all the acceptable channels. The new parameter
allows this to be done without such a list.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is to comply with uniform spreading requirement for ETSI domain
(section 4.7.2.7 in EN 301 893 - V1.8.1). ETSI uniform spreading
requires equal probability for the usable channels. The previous channel
selection logic after a radar detection did not fully comply with the
uniform spreading requirement for the domain by ignoring DFS channels.
Consider DFS channels also during channel selection when the current DFS
domain is ETSI.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Derive PMK-R0 and the relevant key names when using FILS authentication
for initial FT mobility domain association.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends fils_pmk_to_ptk() to allow FILS-FT to be derived. The
callers do not yet use that capability; i.e., actual use will be added
in separate commits.
Signed-off-by: Jouni Malinen <j@w1.fi>
The conditional gSTA and gAP (DH public keys) were not previously
included in Key-Auth derivation, but they are needed for the PFS case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Enable use of FT RRB without configuring each other AP locally. Instead,
broadcast messages are exchanged to discover APs within the local
network.
When an R0KH or R1KH is discovered, it is cached for one day.
When a station uses an invalid or offline r0kh_id, requests are always
broadcast. In order to avoid this, if r0kh does not reply, a temporary
blacklist entry is added to r0kh_list.
To avoid blocking a valid r0kh when a non-existing pmk_r0_name is
requested, r0kh is required to always reply using a NAK. Resend requests
a few times to ensure blacklisting does not happen due to small packet
loss.
To free newly created stations later, the r*kh_list start pointer in
conf needs to be updateable from wpa_auth_ft.c, where only wconf is
accessed.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This adds a counter and adds sequence numbering to FT RRB packets. The
sequence number is checked against r0kh/r1kh sequence number cache.
Special attention is needed in case the remote AP reboots and thus loses
its state. I prefer it to recover automatically even without synchronized
clocks. Therefore an identifier called dom is generated randomly along the
initial sequence number. If the dom transmitted does not match or the
sequence number is not in the range currently expected, the sender is asked
for a fresh confirmation of its currently used sequence numbers. The packet
that triggered this is cached and processed again later.
Additionally, in order to ensure freshness, the remote AP includes an
timestamp with its messages. It is then verified that the received
messages are indeed fresh by comparing it to the older timestamps
received and the time elapsed since then. Therefore FT_RRB_TIMESTAMP is
no longer needed.
This assigns new OUI 00:13:74 vendor-specific subtype 0x0001 subtypes:
4 (SEQ_REQ) and 5 (SEQ_RESP).
This breaks backward compatibility, i.e., hostapd needs to be updated
on all APs at the same time to allow FT to remain functional.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Convert FT RRB into a new TLV based format. Use AES-SIV as AEAD cipher
to protect the messages.
This needs at least 32 byte long keys. These can be provided either
by a config file change or letting a KDF derive the 32 byte key used
from the 16 byte key given.
This breaks backward compatibility, i.e., hostapd needs to be updated on
all APs at the same time to allow FT to remain functional.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Replace the previously used extension of IEEE 802.11 managed Ethertype
89-0d (originally added for Remote Request/Response in IEEE 802.11r)
with Ethertype 88-b7 (OUI Extended EtherType) for FT inter-AP
communication. The new design uses a more properly assigned identifier
for the messages.
This assigns the OUI 00:13:74 vendor-specific subtype 0x0001 for the new
hostapd AP-to-AP communication purposes. Subtypes 1 (PULL), 2 (RESP),
and 3 (PUSH) are also assigned in this commit for the R0KH-R1KH
protocol.
This breaks backward compatibility, i.e., hostapd needs to be updated on
all APs at the same time to allow FT to remain functional.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Commit 941caed980 ('MBO: Add MBO
ANQP-element processing on AP') changed the design by using the
rx_anqp_vendor_specific() function to process all ANQP vendor specific
elements. However, the caller for this was within ifdef CONFIG_HS20
block. Fix this by calling the function even in CONFIG_HS20=y is not
included in the build. This fixes CONFIG_MBO=y builds without
CONFIG_HS20=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
When starting AP in HT40 mode and both HT40+ and HT40- options are
specified in hostapd.conf, select a valid secondary channel for the AP
automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow this function to be called from outside ieee802_11.c and with the
final steps replaced through a callback function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This function does not need the frame header, so pass in only the IE
area to make it easier to share this for driver-based AP SME handling.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is used with partial AP SME in driver cases to enable FILS
association (AES-SIV) processing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to add more parameters without having to change the
callback function prototype.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
MDE was already added with RSNE, but FTE needed to be added to the FILS
Authentication frame for the FT initial mobility domain association
using FILS authentication case.
Signed-off-by: Jouni Malinen <j@w1.fi>
With AP-AP communication, when hapd0 sends a packet, hapd1 can receive
it immediately and send a response. But hapd0 will only read and process
the response after it has returned from the sending context, that is
entered eloop again. So one does not need to consider the RX function of
the reply to run for the request sending hapd before the send calling
function has returned.
Previously, with intra-process communication, the packet is not
scheduled through eloop. Thus the RX handler of the reply might be run
while the sending context of the original request has not returned.
This might become problematic, e.g., when deferring a management frame
processing until an RRB response is received and then have the request
restarted and finished before the original request handling has been
stopped.
I'm not aware of any concrete bug this is currently triggering but came
across it while thinking of FT RRB AP-AP sequence numbering.
I think the non-eloop scheduling approach might be error-prone and thus
propose to model it more closely to the way the message would be
received from a socket. Additionally, this ensures that the tests model
AP-AP communication more closely to real world.
Solution: queue these packets through eloop.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
With multiple interface like AP and station which is already
associated to some other AP, when we try to do channel switch
for the AP mode (different from the operation channel support of
station) and if the AP channel switch fails continously (including
the fallback channel switch), results in a crash due to NULL pointer
dereference. This is because hostapd_deinit_driver() assigns the
driver context (drv_priv) to NULL as we are not able to bring up
the interface with a new channel
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
This fixes the following compiler warning:
wpa_auth.c:4249:34: error: address of array 'a->conf.fils_cache_id'
will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds an option to configure hostapd to enable use of perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime configuration parameter fils_dh_group is used to enable this
by specifying which DH group to use. For example, fils_dh_group=19 would
allow FILS SK PFS to be used with a 256-bit random ECP group.
Signed-off-by: Jouni Malinen <j@w1.fi>
draft-harkins-owe-07.txt does not specify these parameters, so need to
pick something sensible to use for the experimental implementation. The
Suite B 128-bit level AKM 00-0F-AC:11 has reasonable parameters for the
DH group 19 case (i.e., SHA256 hash), so use it for now. This can be
updated if the OWE RFC becomes clearer on the appropriate parameters
(KEK/KCK/MIC length, PRF/KDF algorithm, and key-wrap algorithm).
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds AP side processing for OWE Diffie-Hellman Parameter element in
(Re)Association Request frame and adding it in (Re)Association Response
frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the GAS server to process MBO ANQP-elements and reply to a
query for the Cellular Data Connection Preference (if configured). The
new configuration parameter mbo_cell_data_conn_pref can be used to set
the value (0, 1, or 255) for the preference to indicate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
As FCC DFS requirement does not explicitly mention about the validity of
the (pre-)CAC when channel is switched, it is safe to assume that the
pre-CAC result will not be valid once the CAC completed channel is
switched or radar detection is not active on the (CAC completed) channel
within a time period which is allowed (10 seconds - channel switch time)
as per FCC DFS requirement.
Use the new driver event to allow the driver to notify expiry of the CAC
result on a channel. Move the DFS state of the channel to 'usable' when
processing pre-CAC expired event. This means any future operation on
that channel will require a new CAC to be completed. This event is
applicable only when DFS is not offloaded to the kernel driver.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
When DFS channel state is shared across multiple radios on the system it
is possible that a CAC completion event is propagated from other radio
to us. When in enabled state, do not proceed with setup completion upon
processing CAC completion event with devices where DFS is not offloaded,
when in state other than enabled make sure the configured DFS channel is
in available state before start the AP.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
This leads to cleaner code overall, and also reduces the size
of the hostapd and wpa_supplicant binaries (in hwsim test build
on x86_64) by about 2.5 and 3.5KiB respectively.
The mechanical conversions all over the code were done with
the following spatch:
@@
expression SIZE, SRC;
expression a;
@@
-a = os_malloc(SIZE);
+a = os_memdup(SRC, SIZE);
<...
if (!a) {...}
...>
-os_memcpy(a, SRC, SIZE);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was possible to hit a double-free on the l2_packet socket if
initialization of DHCP/NDISC snoop failed on a hostapd interface that
had previously had those enabled successfully. Fix this by clearing the
l2_packet pointers during deinit.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf parameter country3 can now be used to configure the
third octet of the Country String that was previously hardcoded to ' '
(= 0x20).
For example:
All environments of the current frequency band and country (default)
country3=0x20
Outdoor environment only
country3=0x4f
Indoor environment only
country3=0x49
Noncountry entity (country_code=XX)
country3=0x58
IEEE 802.11 standard Annex E table indication: 0x01 .. 0x1f
Annex E, Table E-4 (Global operating classes)
country3=0x04
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When getting the channel number from a frequency, all supported modes
should be checked rather than just the current mode. This is needed when
hostapd switches to a channel in different band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The __FAVOR_BSD macro was previously used in netinet/udp.h to select
between two different names of the variables in struct udphdr. Define
that to force the versions with the uh_ prefix. In addition, use the
same style consistently within fils_hlp.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new broadcast_deauth parameter can be used to disable sending of the
Deauthentication frame whenever AP is started or stopped. The default
behavior remains identical to the past behavior (broadcast_deauth=1).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 01e2231fdc ('hostapd: Skip some
configuration steps for mesh cases') removed some operations based on
hapd->iface->mconf being NULL. This was within #ifdef CONFIG_MESH, so it
should not impact hostapd, but it can impact AP mode with
wpa_supplicant. That does not sound intentional, so make these
conditional on hapd->conf->mesh being enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows PMKSA cache entries to be shared between all the BSSs
operated by the same hostapd process when those BSSs use the same FILS
Cache Identifier value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE 802.11ax HE changes to include HE IEs in Beacon and Probe Response
frames. These elements are using vendor specific forms for now since the
IEEE 802.11ax draft is not yet finalized and the element contents is
subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add IEEE 802.11ax definitions for config, IEEE structures, and
constants. These are still subject to change in the IEEE process.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Let mesh STA A be a STA which has config disable_ht=0 and disable_vht=1.
Let mesh STA B be a STA which has config disable_ht=0 and disable_vht=0.
The mesh STA A and B was connected.
Previously, the mesh STA A sent frame with VHT rate even though its VHT
was disabled. This commit fixes the issue by checking the local BSS VHT
configuration.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Let mesh STA A be a STA which has config disable_ht=1.
Let mesh STA B be a STA which has config disable_ht=0.
The mesh STA A and B was connected.
Previously, the mesh STA A sent frame with HT rate even though its HT
was disabled. This commit fixes the issue by checking the local BSS HT
configuration.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
While the FILS authentication cases were already using the proper PMK
length (48 octets instead of the old hardcoded 32 octet), the initial
association case had not yet been updated to cover the new FILS SHA384
AKM and ended up using only a 32-octet PMK. Fix that to use 48-octet PMK
when using FILS SHA384 AKM.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, any potential (even if very unlikely) local operation error
was ignored. Now these will result in aborting the negotiation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The url argument to ieee802_11_send_bss_trans_mgmt_request() was
hardcoded to NULL in the only caller, so this code cannot be reached.
wnm_send_bss_tm_req() construct the same frame with more generic
parameters, including option for including the URL, so
ieee802_11_send_bss_trans_mgmt_request() can be simplified.
Signed-off-by: Jouni Malinen <j@w1.fi>
The length of the WNM-Sleep element was not verified before using it.
This could result in reading the subfields in this element (total of
four octets) beyond the end of the buffer. Fix this by ignoring the
element if it is not long enough to contain all the subfields.
Signed-off-by: Jouni Malinen <j@w1.fi>
The struct wpa_stsl_negotiation seemed to have been for some kind of
tracking of state of PeerKey negotiations within hostapd. However,
nothing is actually adding any entries to wpa_auth->stsl_negotiations or
using this state. Since PeerKey does not look like something that would
be deployed in practice, there is no justification to spend time on
making this any more complete. Remove the dead code now instead of
trying to figure out what it might be used for.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the int medium_time variable to overflow, so use a
64-bit unsigned integer to get a large enough value for the
multiplication.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to maintain different return paths for STA being
completely not present and not authorized, so merge these into a single
case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This 16-bit field uses little endian encoding and it must be read with
WPA_GET_LE16() instead of assuming host byte order is little endian. In
addition, this could be misaligned, so using a u16 pointer here was not
appropriate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hapd->acl_cache and hapd->acl_queries were not reset back to NULL in
hostapd_acl_deinit() when cached results and pending ACL queries were
freed. This left stale pointers to freed memory in hapd. While this was
normally followed by freeing of the hapd data, it is possible to re-use
that hapd when disabling and re-enabling an interface. That sequence
could result in use of freed memory if done while there were cached
results or pending ACL operations with a RADIUS server (especially, if
that server did not reply).
Fix this by setting hapd->acl_queries to NULL when the pending entries
are freed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The "!wpabuf_resize(...) == 0" condition does not make any sense. It
happens to work, but this is really supposed to simple check with
wpabuf_resize() returns non-zero and "wpabuf_resize(...)" is the
cleanest way of doing so.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the OSU Providers configuration was invalid (included osu_server_uri
but not osu_method_list), it was possible for the GAS response
generation to hit a NULL dereference. Fix this by checking for the
invalid configuration before trying to fill in the OSU methods.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It can happen if the station is unreachable or sleeping longer than
the actual total GTK rekey timeout. To fix the latter case
wpa_group_update_count may be increased.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
wpa_group_update_count and wpa_pairwise_update_count can now be used to
set the GTK and PTK rekey retry limits (dot11RSNAConfigGroupUpdateCount
and dot11RSNAConfigPairwiseUpdateCount). Defaults set to current
hardcoded value (4).
Some stations may suffer from frequent deauthentications due to GTK
rekey failures: EAPOL 1/2 frame is not answered during the total timeout
period of currently ~3.5 seconds. For example, a Galaxy S6 with Android
6.0.1 appears to go into power save mode for up to 5 seconds. Increasing
wpa_group_update_count to 6 fixed this issue.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
Some channels fail to be set, when falling back to 20 MHz, due to
remaining VHT info of center freq. As we are going to 20 MHz, reset the
VHT center frequency segment information as well.
Signed-off-by: Eduardo Abinader <eduardoabinader@gmail.com>
Commit 91d91abf6f ('FILS: DHCP relay for
HLP requests') added steps that are conditional on sta->fils_hlp_resp
being non-NULL. One of these cases within send_assoc_resp() was properly
protected from sta == NULL error case (that is now possible after a
recent DMG change), but the first one was not. A DMG error case in a
CONFIG_FILS=y build could have hit a NULL pointer dereference here. Fix
this by verifying sta != NULL more consistently.
Signed-off-by: Jouni Malinen <j@w1.fi>
P802.11i/D3.0 described the Key Length as having value 16 for the group
key handshake. However, this was changed to 0 in the published IEEE Std
802.11i-2004 amendment (and still remains 0 in the current standard IEEE
Std 802.11-2016). We need to maintain the non-zero value for WPA (v1)
cases, but the RSN case can be changed to 0 to be closer to the current
standard.
Signed-off-by: Jouni Malinen <j@w1.fi>
While the IEEE Std 802.11-2016 is still indicating that GNonce would be
exchanged in EAPOL-Key messages (see, e.g., Figure 12-52 showing the
Send EAPOL-Key operation in the REKEYNEGOTIATING state or the sample
group key handshake in Figure 12-47), there are also examples of
describing this field as having value zero (e.g., 12.7.7.2 Group key
handshake message 1).
GNonce is used only with the Authenticator and the Supplicant does not
have any use for it, so it is better not to expose that internal value.
Hardcode the Key Nonce field to 0 in EAPOL-Key group message 1/2.
Signed-off-by: Jouni Malinen <j@w1.fi>
sm->Pair needs to be initialized to TRUE since unicast cipher is
supported and this is an ESS. However, the normal place for setting this
(WPA_PTK::INITIALIZE) is skipped with using FT protocol or FILS
authentication, so need to do that separately when forcing PTKINITDONE.
Signed-off-by: Jouni Malinen <j@w1.fi>
The local custom version of allocating and initializing struct
hostapd_data within wpa_supplicant_mesh_init() is problematic. This has
already missed couple of initialization steps that are required. Instead
of trying to remember to keep this up to date, use
hostapd_alloc_bss_data() so that there is only one place for this
initialization.
This is fixing a recent issue where FILS HLP started using
hapd->dhcp_server and expected that to be initialized to -1. For the
mesh case, that did not happen and when removing the interface, the FILS
HLP implementation ended up unregistering eloop socket for
hapd->dhcp_server (= 0). This could result in missing socket callbacks
for an arbitrary socket.
Signed-off-by: Jouni Malinen <j@w1.fi>
The hostapd processing of the AES-SIV AAD was incorrect. The design for
the AAD changed between P802.11ai/D7.0 and D8.0 from a single vector
with concatenated data to separate vectors. The change in the
implementation had missed the change in the aes_siv_decrypt() call for
the num_elem parameter. This happened to work with the mac80211
implementation due to a similar error there.
Fix this by using the correct numbers of vectors in the SIV AAD so that
all the vectors get checked. The last vector was also 14 octets too long
due to incorrect starting pointer, so fix that as well. The changes here
are not backwards compatible, i.e., a similar fix in the Linux mac80211
is needed to make things interoperate again.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new dhcp_server configuration parameter can now be used to configure
hostapd to act as a DHCP relay for DHCPDISCOVER messages received as
FILS HLP requests. The dhcp_rapid_commit_proxy=1 parameter can be used
to configure hostapd to convert 4 message DHCP exchange into a 2 message
exchange in case the DHCP server does not support DHCP rapid commit
option.
The fils_hlp_wait_time parameter can be used to set the time hostapd
waits for an HLP response. This matches the dot11HLPWaitTime in IEEE Std
802.11ai-2016.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is independent functionality from the core IEEE 802.11 management
handling and will increase significantly in size, so it is cleaner to
maintain this in a separate source code file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not depend on undefined behavior with pointer arithmetic when
checking whether there is sufficient room for an option.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These can be reused for other purposes than just the DHCP snoofing for
Proxy ARP. In addition, use more complete definition of the parameters
based on the current IANA registry.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
With device_ap_sme disabled, ACL was checked upon authentication
request. In 802.11ad there is no authentication phase so need to check
ACL upon association.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Previously, the temporary STA session timeout was set to 5 seconds. If
gas_comeback_delay is configured to be longer than 5 seconds, GAS
Comeback Response frame can't include queried information as all pending
data has already been cleared due to session timeout. This commit
resolves the issue by setting session timeout to be larger than
gas_comeback_delay.
Signed-off-by: Daniel Kim <kimdan@qca.qualcomm.com>
Instead of copying the struct wpa_auth_callbacks, just keep a pointer to
it, keep the context pointer separate, and let the user just provide a
static const structure. This reduces the attack surface of heap
overwrites, since the function pointers move elsewhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds parsing of received FILS HLP requests from (Re)Association
Request frames. The reassembled requests are verified to be in valid
format and are printed in debug output. However, actual processing or
forwarding of the packets is not yet implemented, i.e., the vendor
specific frame filtering logic is for now practically dropping all HLP
requests.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These commnds are mesh version of PMKSA_GET/ADD commands. So the usage
and security risk is similar to them. Refer to
commit 3459381dd2 ('External persistent
storage for PMKSA cache entries') also.
The MESH_PMKSA_GET command requires peer MAC address or "any" as an
argument and outputs appropriate stored PMKSA cache. And the
MESH_PMKSA_ADD command receives an output of MESH_PMKSA_GET and re-store
the PMKSA cache into wpa_supplicant. By using re-stored PMKSA cache,
wpa_supplicant can skip commit message creation which can use
significant CPU resources.
The output of the MESH_PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <expiration in seconds>
The example of MESH_PMKSA_ADD command is this.
MESH_PMKSA_ADD 02:00:00:00:03:00 231dc1c9fa2eed0354ea49e8ff2cc2dc cb0f6c9cab358a8146488566ca155421ab4f3ea4a6de2120050c149b797018fe 42930
MESH_PMKSA_ADD 02:00:00:00:04:00 d7e595916611640d3e4e8eac02909c3c eb414a33c74831275f25c2357b3c12e3d8bd2f2aab6cf781d6ade706be71321a 43180
This functionality is disabled by default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Relational operators (==) have higher precedence than the ternary
conditional in C. The last_subtype check for association/reassociation
was broken due to incorrect assumption about the precedence. Fix this by
adding parenthesis around the ternary conditional.
The previous implementation worked for Association Request frames by
accident since WLAN_FC_STYPE_ASSOC_REQ happens to have value 0 and when
the last receive frame was an Association Request frame, the
sta->last_subtype == reassoc check was true and non-zero
WLAN_FC_STYPE_REASSOC_REQ was interpreted as true. However, this was
broken for Reassociation Request frame. reassoc == 1 in that case could
have matched received Association Response frame (subtype == 1), but
those are not received in AP mode and as such, this did not break other
behavior apart from not being able to drop duplicated Reassociation
Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds helper functions for deriving PMK and PMKID from ERP exchange
in FILS shared key authentication as defined in IEEE Std 802.11ai-2016,
12.12.2.5.2 (PMKSA key derivation with FILS authentication). These
functions is used to fix PMK and PMKID derivation which were previously
using the rMSK directly as PMK instead of following the FILS protocol to
derive PMK with HMAC from nonces and rMSK.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Check the action TX status callback contents more thoroughly and report
the BEACON-REQ-TX-STATUS event only if the Measurement Type indicates
beacon report.
Signed-off-by: Jouni Malinen <j@w1.fi>
Authentication and Deauthentication frames are not used in DMG/IEEE
802.11ad networks. For DMG/IEEE 802.11ad the following was implemented:
Upon receiving association request, allocate the sta object and
initialize it as if authentication took place. Upon receiving
disassociation, deallocate the sta object.
ap_sta_disassociate/ap_sta_deauthenticate/ap_sta_disconnect all use
disassociation instead of deauthentication. In driver_nl80211,
i802_sta_deauth() is routed to i802_sta_disassoc().
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Supported Rates element is not present in DMG/IEEE 802.11ad frames. Make
copy_supp_rates() immediately return with success if hardware mode is
IEEE 802.11ad.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
The new hostapd control interface event "BEACON-RESP-RX <STA address>
<dialog token> <report mode> <beacon report>" is now used to report
received beacon reports as a reponse to the REQ_BEACON operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new BEACON-REQ-TX-STATUS control interface event is now used to
report whether a beacon request (from REQ_BEACON command) was delivered
successfully. This event has the following parameters: <STA address>
<dialog token> <ack=0/1>.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new control interface command "REQ_BEACON <STA addr>
[req_mode=<mode>] <beacon request>" can now be used to request hostapd
to transmit a measurement request to request a beacon report from an
associated STA. This command returns the assigned dialog token (1-255)
or FAIL on failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
The loop to add hash values was supposed to be limited to at most 10000
values, but the count variable was not being decremented in the loop.
Fix this by decrementing counting for each iteration. This fixes
ANQP-element format in the unlikely case of there being more than 10000
configuration realms.
Signed-off-by: Jouni Malinen <j@w1.fi>
The actual BSS configuration parameter can be updated with the SET
control interface command, so there is no need to maintain a separate
per-BSS parameter and a separate control interface handling for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the hostapd ft_over_ds parameter was used to only advertise
whether FT-over-DS is enabled in MDE and leave it to the stations to
follow that advertisement. This commit extends this to explicitly reject
(silently drop) FT Action frames if a station does not follow the
advertised capabilities.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, this was noted in error log, but the invalid value was
stored in the configuration without rejecting it.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible to try to do driver operations before the driver
interface had been initialized when processing a SIGHUP signal. This
would result in NULL pointer dereference. Fix this by skipping the steps
when SIGHUP is issued before the interface is enabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function is already checking the fname argument against NULL, so
use that check on its own instead of duplicating the check in the only
caller.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is apparently possible for the NL80211_CMD_UNEXPECTED_4ADDR_FRAME
event to be delivered to hostapd before the NL80211_CMD_FRAME_TX_STATUS
event for (Re)Association Response frame. This resulted in the 4-address
WDS mode not getting enabled for a STA. This could occur in particular
when operating under heavy load and the STA is reconnecting to the same
AP in a sequence where Deauthentication frame is followed immediately by
Authentication frame and the driver event processing gets delayed due to
removal of the previous netdev taking time in the middle of this
sequence.
Fix this by recording a pending item for 4-address WDS enabling if the
NL80211_CMD_UNEXPECTED_4ADDR_FRAME event would have been dropped due to
incompleted association and then process this pending item if the TX
status for the (Re)Association Response frame is received and it shows
that the frame was acknowledged.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd configuration parameter fils_realm=<realm> can now be
used to configure one or more FILS realms to advertise for ERP domains
when using FILS. This replaces the use of erp_domain=<domain> parameter
for the FILS use case.
Signed-off-by: Jouni Malinen <j@w1.fi>
P802.11ai/D7.0 changed from CRC32 to SHA256 as the hash algorithm for
the FILS realm name. Update the implementation to match that change.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the secondary channel was not found at all, no debug print was shown
to indicate that the channel was rejected due to that problem. Print a
clearer message indicating which channel was behind the reason to reject
channel configuration as unsuitable for AP mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd didn't send "TERMINATING" event when stopped by
SIGTERM. Android handles this event to stop monitor thread.
This commit adds "TERMINATING" event same as with wpa_supplicant.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
Previously, os_sleep() was used to block the hostapd (or wpa_supplicant
AP/P2P GO mode) processing between sending out EAP-Failure and
disconnecting the STA. This is not ideal for couple of reasons: it
blocks all other parallel operations in the process and it leaves a
window during which the station might deauthenticate and the AP would
have no option for reacting to that before forcing out its own
Deauthentication frame which could go out after the STA has already
started new connection attempt.
Improve this design by scheduling an eloop timeout of 10 ms instead of
the os_sleep() call and perform the delayed operations from the eloop
callback function. This eloop timeout is cancelled if the STA
disconnects or initiates a new connection attempt before the 10 ms time
is reached. This gets rid of the confusing extra Deauthentication frame
in cases where the STA reacts to EAP-Failure by an immediate
deauthentication.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds support for nl80211 NL80211_CMD_SET_MULTICAST_TO_UNICAST
command.
By setting the new hostapd configuration option multicast_to_unicast=1,
hostapd configures this AP to perform multicast to unicast conversion.
When enabled, all multicast packets with ethertype ARP, IPv4, or IPv6
(possibly within an 802.1Q header) will be sent out to each station once
with the destination (multicast) MAC address replaced by the station's
MAC address. Note that this may break certain expectations of the
receiver, e.g., the ability to drop unicast IP packets encapsulated in
multicast L2 frames, or the ability to not send destination unreachable
messages in such cases.
This also does not implement Directed Multicast Service (DMS).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
We should unconditionally remove inactivity timers for wired network
cases. This commit checks for this after a new station association:
hapd->iface->drv_flags & WPA_DRIVER_FLAGS_WIRED
and then cancels the timeout and does not register a new one.
It prints out a debug message like this:
1476740180.276286: IEEE 802.1X: 00:02:00:00:00:07 CTRL_DIR entering
state FORCE_BOTH
1476740180.276295: hostapd_new_assoc_sta: canceled wired ap_handle_timer
timeout for 00:02:00:00:00:07
This was tested on a debian jessie amd64 system with a configured 120
second inactivity timer and the session did not timeout.
Signed-off-by: Sam Tannous <stannous@cumulusnetworks.com>
Data connection was lost if a station reassociated without the STA entry
being cleaned up on the AP side. Fix this by moving reconfiguration of
the STA WDS parameters in association response callback to happen only
after the STA flags have been updated to associated stated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes a regression from commit
bb598c3bdd ('AP: Add support for full
station state'). That commit added code to remove and re-add the kernel
STA entry when processing Authentication frames with a driver that
advertises support for full AP client state. That resulted in bypassing
PMF protections for unprotected Authentication frames with such drivers
since the TK was lost in this operation.
It is simplest to skip the STA entry clearing in this type of case
completely to leave the TK in place and to process the new
authentication exchange otherwise normally. This matches the behavior
used with the drivers that do not implement full AP client state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11-2012, 12.4.2 states that if an MDE is present in an
(Re)Association Request frame but the RSNE uses a non-FT AKM suite, the
AP shall reject the association using status code 43 ("Invalid AKMP").
wpa_validate_wpa_ie() now explicitly checks for this condition to meet
this requirement instead of simply ignoring the MDE based on non-FT AKM.
Signed-off-by: Will Glynn <will@willglynn.com>
Allow configuration of Beacon frame TX rate from hostapd.conf with
"beacon_rate=xx" option. The following format is used to set
legacy/HT/VHT beacon rates:
Legacy (CCK/OFDM rates):
beacon_rate=<legacy rate in 100 kbps>
HT:
beacon_rate=ht:<HT MCS>
VHT:
beacon_rate=vht:<VHT MCS>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the anqp_elem configuration parameter support for new Info
IDs (270 (TDLS Capability) was previously missed from the list of
defined values, 280 has already been assigned in REVmc/D8.0; 281..299
are yet to be assigned). No additional source code changes are needed to
allow hostapd to advertise support for these if the ANQP-element value
is set with the anqp_elem parameter.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, CONFIG_IEEE80211R enabled build that supports FT for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode FT is required and there is no need for AP mode FT.
Add support to differentiate between station mode FT and AP mode FT in
wpa_supplicant builds by adding CONFIG_IEEE80211R_AP that should be used
when AP mode FT support is required in addition to station mode FT. This
allows binary size to be reduced for builds that require only the
station side FT functionality.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The Channel Center Frequency Segment subfields use the channel index
instead of frequency in MHz.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
The return value from this function may be used in an outgoing message,
so use a valid status code instead of -1.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add a configuration option in hostapd.conf and in neighbor report that
sets an AP as stationary. To enable this option on the current AP set
the config option stationary_ap to 1. To set a neighbor entry to be
marked as stationary add the word stat to the SET_NEIGHBOR command. This
option tells hostapd to send LCI data even if it is older than requested
by max age subelement in RRM request.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
It is possible that a LCI or location civic configuration buffer
is valid but contains no data. In such a case do not add the LCI
and location civic information to the entry in the neighbor
data base.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This has already been done for WEP, but there's same constraint for not
allowing VTH rates in case of TKIP.
Signed-off-by: Filip Matusiak <filip.matusiak@tieto.com>
Add signal level information to the station tracking information. Also
make it available via the "TRACK_STA_LIST" control command.
Signed-off-by: Kevin Mahoney <k.mahoney@cablelabs.com>
This makes wpa_remove_ptk() call to wpa_auth_set_key() more consistent
with all the other calls that verify the return value to keep static
analyzers happier.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements processing of FILS Authentication frame for FILS shared
key authentication with ERP and PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
ieee802_1x_encapsulate_radius() and ieee802_1x_alloc_eapol_sm() need to
be called from FILS processing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This changes 4-way handshake authenticator processing to decrypt the
EAPOL-Key frames using an AEAD cipher (AES-SIV with FILS AKMs) before
processing the Key Data field. This replaces Key MIC validation for the
cases where AEAD cipher is used. This needs to move the EAPOL-Key msg
2/4 RSN element processing to happen only after the PTK has been derived
and validated. That is done for all AKMs to avoid extra complexity with
having to maintain two code paths for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Suite B 192-bit addition from IEEE Std 802.11ac-2013 replaced the
previous fixed length Key MIC field with a variable length field. That
change was addressed with an addition of a new struct defined for the
second MIC length. This is not really scalable and with FILS coming up
with a zero-length MIC case for AEAD, a more thorough change to support
variable length MIC is needed.
Remove the Key MIC and Key Data Length fields from the struct
wpa_eapol_key and find their location based on the MIC length
information (which is determined by the AKMP). This change allows the
separate struct wpa_eapol_key_192 to be removed since struct
wpa_eapol_key will now include only the fixed length fields that are
shared with all EAPOL-Key cases in IEEE Std 802.11.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Calculate the hashed realm from hostapd erp_domain configuration
parameter and add this to the FILS Indication element when ERP is
enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If FILS is enabled, indicate that in Beacon, Probe Response, and
(Re)Association Response frames in the Extended Capabilities element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds CONFIG_FILS=y build configuration option and new key
management options for FILS authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Station should be able to connect initially without ft_pmk_cache filled,
so the target AP has the PSK available and thus the same information as
the origin AP. Therefore neither caching nor communication between the
APs with respect to PMK-R0 or PMK-R1 or VLANs is required if the target
AP derives the required PMKs locally.
This patch introduces the generation of the required PMKs locally for
FT-PSK. Additionally, PMK-R0 is not stored (and thus pushed) for FT-PSK.
So for FT-PSK networks, no configuration of inter-AP communication is
needed anymore when using ft_psk_generate_local=1 configuration. The
default behavior (ft_psk_generate_local=0) remains to use the pull/push
protocol.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The reason detail field was removed from non_pref_chan attr in MBO
v0.0_r25 draft. Don't parse for this element to be compliant with the
latest drafr.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A weakness in the initial client taxonomy mechanism is from storing both
the Probe and Associate in struct sta_info. struct sta_info is created
after a client associates (or starts authentication frame exchange),
which means that any Probe Request frames sent prior to association are
not retained. The Associate Request frame has to be seen, and then
another Probe Request frame after association, before we have a
signature for the client.
Most clients send lots of Probe Request frames (lots and lots and lots
of Probes, actually), but a few do not. ChromeOS is notably sparing in
sending Probe Request frames, it can take a long time before a signature
for a ChromeOS device is available.
Store the most recent Probe Request frame in struct hostapd_sta_info
tracking list. When a struct sta_info is created, move the Probe Request
frame information from struct hostapd_sta_info to struct sta_info.
Signed-off-by: dgentry@google.com (Denton Gentry)
Signed-off-by: denny@geekhold.com (Denton Gentry)
Signed-off-by: rofrankel@google.com (Richard Frankel)
Signed-off-by: richard@frankel.tv (Richard Frankel)
Implement the signature mechanism described in the paper
"Passive Taxonomy of Wifi Clients using MLME Frame Contents"
published by Denton Gentry and Avery Pennarun.
http://research.google.com/pubs/pub45429.htmlhttps://arxiv.org/abs/1608.01725
This involves:
1. Add a CONFIG_TAXONOMY compile option. Enabling taxonomy incurs
a memory overhead of up to several kilobytes per associated
station.
2. If enabled, store the Probe Request and (Re)Associate Request frame in
struct sta_info.
3. Implement code to extract the ID of each Information Element,
plus selected fields and bitmasks from certain IEs, into a
descriptive text string. This is done in a new source file,
src/ap/taxonomy.c.
4. Implement a "signature qq:rr:ss:tt:uu:vv" command
in hostapd_cli to retrieve the signature.
Signatures take the form of a text string. For example, a signature
for the Nexus 5X is:
wifi4|probe:0,1,127,45,191,htcap:01ef,htagg:03,htmcs:0000ffff,vhtcap:338061b2,
vhtrxmcs:030cfffa,vhttxmcs:030cfffa,extcap:00000a0201000040|assoc:0,1,48,45,
221(0050f2,2),191,127,htcap:01ef,htagg:03,htmcs:0000ffff,vhtcap:339071b2,
vhtrxmcs:030cfffa,vhttxmcs:030cfffa,extcap:0000000000000040
Signed-off-by: dgentry@google.com (Denton Gentry)
Signed-off-by: denny@geekhold.com (Denton Gentry)
Signed-off-by: rofrankel@google.com (Richard Frankel)
Signed-off-by: richard@frankel.tv (Richard Frankel)
Previously, struct hostapd_iface sta_seen list head was initialized only
when completing interface setup. This left a window for operation that
could potentially iterate through the list before the list head has been
initialized. While the existing code checked iface->num_sta_seen to
avoid this case, it is much cleaner to initialize the list when struct
hostapd_iface is allocated to avoid any accidental missing of the extra
checks before list iteration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not generate an unused and invalid Request Authenticator (random
value) when constructing Accounting-Request packets. The correct Request
Authenticator is calculated subsequently in radius_msg_finish_acct()
using MD5(msg + shared secret).
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Add configuration options that control publishing of fine timing
measurement (FTM) responder and initiator functionality via bits 70, 71
of Extended Capabilities element. Typically, FTM functionality is
controlled by a location framework outside hostapd. When framework is
activated, it will use hostapd to configure the AP to publish the FTM
functionality. See IEEE P802.11-REVmc/D7.0, 9.4.2.27.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Some deployed stations incorrectly consider nsts capability in
(Re)Association Response frame as required capability instead of maximum
capability and if it is greater than station's capability then beamform
will not happen in uplink traffic.
This commit adds support for an optional workaround to use station's
nsts capability in (Re)Association Response frame if the station's nsts
is less than AP by using the use_sta_nsts=1 configuration parameter.
This configuration is introduced in this commit and it is disabled by
default.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Previously, this was initialized in hostapd_setup_bss() which made it
possible for a REMOVE_NEIGHBOR control interface command to be issued
prior to the list head pointers having been set. That resulted in a NULL
pointer dereference. Fix this by initializing the list head at the time
the data structure gets allocated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Number of hostapd control interface commands (e.g., STATUS-DRIVER) could
result in NULL pointer dereference when issued on not yet enabled BSS.
Fix this by checking that the driver interface has been initialized
before calling the driver_ops function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Various checks should use is_multicast_ether_addr() instead
of hardcoding the equivalent, change it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not include a NAS-Port attribute in Access-Request and
Accounting-Request packets where the Association ID (AID) is 0, i.e.,
not yet assigned or known.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
This can be used to mandate the presence of the Message-Authenticator
attribute on CoA/Disconnect-Request packets.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
There's no need to have a separate variable and open-code a more
complicated version of this, just use is_broadcast_ether_addr().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, HT/VHT state was shown in STATUS based on the configuration
parameter instead of the runtime operational parameters. This could
result in claiming HT/VHT to be enabled even when it was forced to be
disabled due to an incompatible configuration. Clear HT/VHT information
in the STATUS output if HT/VHT has been disabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
reports mesh peer AID to kernel.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This allows the compiler to check that function prototypes match the
implementation. In addition, this gets rid of sparse warnings.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This moves pairwise, group, and management group ciphers to various mesh
data structures to avoid having to hardcode cipher in number of places
through the code. While CCMP and BIP are still the hardcoded ciphers,
these are now set only in one location.
Signed-off-by: Jouni Malinen <j@w1.fi>
The AMPE element includes number of optional and variable length fields
and those cannot really be represented by a fixed struct
ieee80211_ampe_ie. Remove the optional fields from the struct and
build/parse these fields separately.
This is also adding support for IGTKdata that was completely missing
from the previous implementation. In addition, Key RSC for MGTK is now
filled in and used when configuring the RX MGTK for a peer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation was incorrect in forcing the MGTK to be used
as the IGTK as well. Define new variable for storing IGTK and use that,
if set, to configure IGTK to the driver. This commit does not yet fix
AMPE element parsing to fill in this information.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the data structures to allow variable length MGTK to be
stored for RX. This is needed as an initial step towards supporting
different cipher suites.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is initial step in fixing issues in how PMF configuration for RSN
mesh was handled. PMF is an optional capability for mesh and it needs to
be configured consistently in both hostapd structures (to get proper
RSNE) and key configuration (not included in this commit).
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 0603bcb7fe ('hostapd: Process MAC
ACLs on a station association event (SME in driver)') processes MAC ACL
on a station association event for drivers which use AP SME offload but
does not consider the scenario where the drivers offload ACL. This can
result in station disconnection, though the driver accepts the
connection. Address this by avoiding the hostapd ACL check for the
drivers offloading MAC ACL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
eloop deinit calls could trigger segmentation fault if the early error
path is hit before eloop_init() gets called.
Signed-off-by: Jouni Malinen <j@w1.fi>
gas_address3=1 can now be used to force hostapd to use the IEEE 802.11
standards compliant Address 3 field value (Wildcard BSSID when not
associated) even if the GAS request uses non-compliant address (AP
BSSID).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously all TX status events with wildcard BSSID were ignored. This
did not allow Public Action frame TX status to be processed with the
corrected wildcard BSSID use. Fix this to be allowed. In practice, this
affects only test cases since Action frame TX status was not used for
anything else.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11-2012, 10.19 (Public Action frame addressing) specifies
that the wildcard BSSID value is used in Public Action frames that are
transmitted to a STA that is not a member of the same BSS. hostapd used
to use the actual BSSID value for all such frames regardless of whether
the destination STA is a member of the BSS.
Fix this by using the wildcard BSSID in cases the destination STA is not
a member of the BSS. Leave group addressed case as-is (i.e., the actual
BSSID), since both values are accepted. No such frames are currently
used, though.
This version is still using the AP BSSID value in the Address 3 field
for GAS response frames when replying to a GAS request with AP BSSID
instead of Wildcard BSSID. This is left as a workaround to avoid
interoperability issues with deployed STA implementations that are still
using the non-compliant address and that might be unable to process the
standard compliant case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds the necessary changes to support extraction and use of the
extended capabilities specified per interface type (a recent
cfg80211/nl80211 extension). If that information is available,
per-interface values will be used to override the global per-radio
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the simplest case of SAE group negotiation to occur by
selecting the next available group if the peer STA indicates the
previous one was not supported. This is not yet sufficient to cover all
cases, e.g., when both STAs need to change their groups, but at least
some cases are no covered.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd deinit functions were not ready to handle a case where the data
structures were not fully initialized. Make these more robust to allow
wpa_supplicant mesh implementation to use the current deinit design in
OOM error cases without causing NULL pointer dereferences.
Signed-off-by: Jouni Malinen <j@w1.fi>
This new parameter allows hostapd to add Vendor Specific elements into
(Re)Association Response frames similarly to the way vendor_elements
parameter can be used for Beacon and Probe Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 66d464067d ('FT: Register RRB
l2_packet only if FT-over-DS is enabled') disabled RRB l2_packet socket
if ft_over_ds is disabled, but this socket is required for FT
over-the-air, too (FT key distribution). Enable the socket regardless of
ft_over_ds setting if FT is enabled.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
Add FTM range request via RRM. The AP sends Radio measurement request
with FTM range request as a request for the receiving STA to send FTM
requests to the given list of APs. The neighbor report part of the
request is taken from the neighbor database.
The control interface command is:
REQ_RANGE <dst addr> <rand_int> <min_ap> <responder> [<responder>..]
dst addr: MAC address of an associated STA
rand_int: Randomization Interval (0..65535) in TUs
min_ap: Minimum AP Count (1..15); minimum number of requested FTM ranges
between the associated STA and the listed APs
responder: List of BSSIDs for neighboring APs for which a measurement
is requested
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a hostapd control interface command REQ_LCI to request LCI from an
associated station using radio measurement.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Save RM enabled capability element of an associating station if radio
measurement is supported in its capability field.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Process Neighbor Report Request frame and send Neighbor Report Response
frame based on the configured neighbor report data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a configurable neighbor database that includes the content of
Nighbor Report element, LCI and Location Civic subelements and SSID.
All parameters for a neighbor must be updated at once; Neighbor Report
element and SSID are mandatory, LCI and civic are optional. The age of
LCI is set to the time of neighbor update.
The control interface API is:
SET_NEIGHBOR <BSSID> <ssid=SSID> <nr=data> [lci=<data>] [civic=<data>]
To delete a neighbor use:
REMOVE_NEIGHBOR <BSSID> <SSID>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Extend the radio_measurements parameter to save all the supported
RRM capabilities as it's used in RM enabled capabilities element.
Make this parameter not directly configurable via config file (though,
keep the radio_measurements parameter for some time for backwards
compatibility). Instead, add a configuration option to enable neighbor
report via radio measurements. Other features can be added later as
well.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
The hostapd "POLL_STA <addr>" control interface command can be used to
check whether an associated station ACKs a QoS Data frame. The received
ACK for such a frame is reported as an event message ("AP-STA-POLL-OK
<addr>").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The optional tx=0 parameter can be added to the hostapd
DEAUTHENTICATE/DISASSOCIATE command to request disconnection without
transmitting the Deauthentication/Disassociation frame to the STA.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external programs to fetch the driver inactivity value for a
specific STA ("STA <addr>" hostapd control interface command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a legacy client with no P2P PS support is trying to connect to
a P2P GO, the driver should know that, and change its PS behavior
accordingly.
Add a parameter to hostapd_sta_add_params() indicating if P2P PS is
supported by the station and pass this parameter to kernel with nl80211
driver when the station is added/set.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Fix a possible memory leak in decode_tunnel_passwords() if an invalid
passphrase is received from the RADIUS server.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
This struct in the union is empty, but the design of using a zero-length
u8 array here is not fully compatible with C++ and can result in
undesired compiler warnings. Since there are no non-IE fields in the
Probe Request frames, get the location of the variable length IEs simply
by using the pointer to the frame header and the known header length.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was only used for providing an option to use linux/if_packet.h
instgead of netpacket/packet.h in src/ap/iapp.c. However,
netpacket/packet.h is nowadays commonly available and hostapd already
depends on it through src/l2_packet/l2_packet_linux.c, so there is no
need to continue to provide this option for the kernel header.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of need to include linux/if_vlan.h and additional defines
in vlan_ioctl.c to avoid issues with missing definitions in libc
headers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Due to both <netinet/in.h> (in "utils/includes.h") and <linux/in6.h> (in
<linux/if_bridge.h>) being included, the in6_addr is being redefined:
once from the C library headers and once from the Linux kernel headers.
This causes some build failures with for example the musl C library:
In file included from /usr/include/linux/if_bridge.h:18,
from ../src/ap/vlan_init.c:17:
/usr/include/linux/in6.h:32: error: redefinition of 'struct in6_addr'
/usr/include/linux/in6.h:49: error: redefinition of 'struct sockaddr_in6'
/usr/include/linux/in6.h:59: error: redefinition of 'struct ipv6_mreq'
Mixing C library and Linux kernel headers is a bit problematic [1] and
should be avoided if possible [2]. In order to fix this, define just the
macros needed from <linux/if_bridge.h> as done in Busybox for the brctl
applet [3].
[1] https://sourceware.org/bugzilla/show_bug.cgi?id=15850
[2] http://www.openwall.com/lists/musl/2015/10/06/1
[3] https://git.busybox.net/busybox/commit/?id=5fa6d1a632505789409a2ba6cf8e112529f9db18
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
With this, vlan_init.c does not need any special header files anymore
and vlan_ifconfig.c does not need hostapd-specific header files that
might conflict with net/if.h on NetBSD.
Signed-off-by: Jouni Malinen <j@w1.fi>
Move the ioctl-based VLAN implementation to a separate file to avoid
need for conditional blocks within vlan_ioctl.c. This removes the
internal CONFIG_VLAN_NETLINK define, i.e., this is now used only in
build configuration (.config) to select whether to include the
vlan_util.c (netlink) or vlan_ioctl.c (ioctl) implementation of the
functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
caddr_t is legacy BSD and should be avoided [1]. While glibc may still
use __caddr_t as the type, Linux kernel does not (it is "void __user *
ifru_data").
This fixes compile errors with the musl libc:
../src/ap/vlan_init.c: In function 'br_delif':
../src/ap/vlan_init.c:218:18: error: '__caddr_t' undeclared (first use in this function)
ifr.ifr_data = (__caddr_t) args;
[1] http://stackoverflow.com/questions/6381526/what-is-the-significance-of-caddr-t-and-when-is-it-used
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
pmksa->pmk or pmksa->pmkid cannot be NULL since they are arrays. Remove
the unnecessary NULL checks and use the provided pmksa pointer directly
to simplify the implementation. (CID 138519)
Signed-off-by: Jouni Malinen <j@w1.fi>
Interface additions/removals are not guaranteed to be for the driver
listening to the kernel events. As such, send the events to
wpa_supplicant_event_global() which can then pick the correct interface
registered with wpa_supplicant to send the event to.
Signed-off-by: Roy Marples <roy@marples.name>
Commit 1889af2e0f ('VLAN: Separate station
grouping and uplink configuration') added an ap_sta_set_vlan() function
that gets called from pmksa_cache_auth.c. This broke CONFIG_IBSS_RSN=y
build if src/ap/sta_info.c did not get included in the build, i.e., if
CONFIG_AP=y was not set.
Fix this by making the ap_sta_set_vlan() call conditional on
CONFIG_NO_VLAN being undefined and define this for CONFIG_IBSS_RSN=y
builds. This is fine for wpa_supplicant since CONFIG_AP=y case was
already defining this. For hostapd, this function call is not needed for
CONFIG_NO_VLAN case either.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This patch add functionality of mesh SAE PMKSA caching. If the local STA
already has peer's PMKSA entry in the cache, skip SAE authentication and
start AMPE with the cached value.
If the peer does not support PMKSA caching or does not have the local
STA's PMKSA entry in the cache, AMPE will fail and the PMKSA cache entry
of the peer will be removed. Then STA retries with ordinary SAE
authentication.
If the peer does not support PMKSA caching and the local STA uses
no_auto_peer=1, the local STA can not retry SAE authentication because
NEW_PEER_CANDIDATE event cannot start SAE authentication when
no_auto_peer=1. So this patch extends MESH_PEER_ADD command to use
duration(sec). Throughout the duration, the local STA can start SAE
authentication triggered by NEW_PEER_CANDIDATE even though
no_auto_peer=1.
This commit requires commit 70c93963ed
('SAE: Fix PMKID calculation for PMKSA cache'). Without that commit,
chosen PMK comparison will fail.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA_FLUSH control interface command to
allow the PMKSA list from the authenticator side to be flushed for AP
and mesh mode. In addition, this adds a hostapd PMKSA_FLUSH control
interface command to flush the PMKSA entries.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA control interface command to allow
the PMKSA list from the authenticator side to be listed for AP and mesh
mode. In addition, this adds a hostapd PMKSA control interface command
to show the same list for the AP case.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
In scenarios where only DFS channels are available (e.g., outdoor,
special country codes), hostapd must be able to handle situations
where all are unavailable.
The two possibilities to get there are
1) while operating on the last available DFS channel a radar is
detected
2) hostapd is started while all channels are unavailable
In both cases, hostapd instead of terminating should better
wait for the NOPs to pass and re-try operation after the CAC.
This patch provides that feature by using the condition
(iface->state == HAPD_IFACE_DFS && !iface->cac_started)
as NOP mode signature to retry operation from within
hostapd_dfs_nop_finished().
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Add a new 'use_driver_iface_addr' configuration parameter to allow use
of the default interface address generated by the driver on interface
creation. This can be useful when specific MAC addresses were allocated
to the device and we want to use them for multi-BSS operation.
Signed-off-by: Eliad Peller <eliad@wizery.com>
There is a race condition in which AP might receive the EAPOL-Start
frame (from the just-associated station) before the TX completion of the
Association Response frame. This in turn will cause the EAPOL-Start
frame to get dropped, and potentially failing the connection.
Solve this by saving EAPOL frames from authenticated-but-not-associated
stations, and handling them during the Association Response frame TX
completion processing.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Add UDP support for ctrl_iface:
New config option could be set:
CONFIG_CTRL_IFACE=udp
CONFIG_CTRL_IFACE=udp-remote
CONFIG_CTRL_IFACE=udp6
CONFIG_CTRL_IFACE=udp6-remote
And hostapd_cli usage:
hostapd_cli -i localhost:8877
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
In case vendor ACS command returns invalid channel or hardware mode,
complete the interface setup with an error code instead of simply
return, so that hostapd can properly clean up the interface setup.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This tells to the server how long we have been trying to transmit the
message so that the actual time of the message generation can be
determined from receive time (ignoring network delays and only at
accuracy of one second).
For interim updates, only value 0 is used since there are no
retransmissions of the same message. For other accounting messages, the
initial attempt goes out with value 0 and the retransmissions, if
needed, show the number of seconds the message has been waiting in the
queue.
Update the Identifier and Authenticator in the messages whenever
updating the Acct-Delay-Time per RFC 2866, 4.1 requirements.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of using the RADIUS client retransmission design with the old
RADIUS message contents for each retry, trigger a completely new interim
accounting update instance more quickly (using the same schedule as
RADIUS message retransmissions) to improve accounting updates in cases
where RADIUS message delivery fails. This allows the server to get up to
date information from the time the "retry" message was sent instead of
the old information from the time the first failed attempt was sent.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to maintain two implementations of the functionality.
is_zero_ether_addr() is easier to understand, so use it.
Signed-off-by: Jouni Malinen <j@w1.fi>
Using rtnl_link_alloc_cache() is expensive as it fills in all configured
links. Using rtnl_link_get_kernel() is much more lightweight.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
As the Linux variant of l2_packet_init() does not use its own_addr
argument and l2_packet_receive() does not filter on destination MAC
address, this needs to be checked in the callback.
If there are multiple BSSes listening for FT RRB packets, all their
BSSIDs need to be local to the bridge interface. As l2_packet_init() is
going to receive all of them going for any local address, those RRB
messages started turning up on BSSes that were not destinated for and
cluttering logs.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
If the AP is slow, passphrase hashing takes too long to serve the client
before timeout. Extend the Tunnel-Password design to allow a 64
character value to be interpreted as a PSK and send SSID to RADIUS
server. This allows the RADIUS server to either take care of passphrase
hashing or to use raw PSK without such hashing.
This is especially important for FT-PSK with FT-over-air, where hashing
cannot be deferred.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Instead of copying the full struct hostapd_sta_wpa_psk_short, share the
existing entry and use reference counting to check when it needs to be
freed. This allows caching of PSKs derived from passphrases to avoid
having to perform the heavy hashing operation multiple times.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Hashing takes quite some time (can be about one second on a low-power
CPU for each passphrase provided), so hostapd can easily hit the 900 ms
Wi-Fi client authentication deadline (mac80211 uses 3x 300 ms). This can
be fixed by storing the passphrase instead of PSK with the STA and defer
the hashing into the WPA/RSN 4-way handshake, when enumerating all PSKs.
This applies for the case where a RADIUS server is used to store the
per-STA passphrases and this passphrase is delivered as part of the MAC
ACL check during IEEE 802.11 Authentication frame processing.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The VLAN ifname is limited to the maximum length of IFNAMSIZ, so there
is no need to use heap allocation for it.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
r1_key_holder is an identifier that was always set to zero if unless
configured before.
See 11.6.1.7.4 of IEEE Std 802.11-2012 which reads
"R1KH-ID is a MAC address of the holder of the PMK-R1 in the
Authenticator of the AP"
See 12.2.2 of IEEE Std 802.11-2012 which reads
"Each R0KH-ID and R1KH-ID is assumed to be expressed as a unique
identifier within the mobility domain."
"The R1KH-ID shall be set to a MAC address of the physical entity
that stores the PMK-R1 ..."
Defaulting this to BSSID is a more reasonable value since we have not
rejected the missing r1_key_holder as invalid configuration.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
A malicious station could try to do FT-over-DS with a non WPA-enabled
BSS. When this BSS is located in the same hostapd instance, internal RRB
delivery will be used and thus the FT Action Frame will be processed by
a non-WPA enabled BSS. This processing used to crash hostapd as
hapd->wpa_auth is NULL. If the target BSS is on a different hostapd
instance, it will not listen for these packets and thus not crash.
Fix this by checking hapd->wpa_auth before delivery.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The FT RRB hostapd packets have a length field. For PULL frames, it
counted the bytes starting with nonce and up to the last before pad. For
RESP frames, it counted the bytes starting with nonce and up to the last
before pad except for 2 bytes. For PUSH frames, it counted the bytes
starting with nonce and up to including pad.
As rounding is done with AES encryption, including pad does not make
sense. Not including the last field before pad does not make sense
either. These were broken in the earlier addition of the 2 octet
pairwise field in commit 1b484d60e5 ('FT:
Include pairwise cipher suite in PMK-R0 SA and PMK-R1 SA').
AES encryption is not affected, as rounding hides the differences. The
packets data_length field is not used, so the differences have no effect
there.
This patch changes the constants to match the bytes used, thus excluding
the pad. To validate the changes, look at remainder modulo 8 of the sum
of the size constants and the padding sizes.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This makes hostapd track Supported Operating Classes information from
the associated STAs. The stored information is available through the STA
control interface command (supp_op_classes row) as a hexdump of the
Supported Operating Classes element starting from the Length field. This
information can be used as input to BSS transition management and
channel switching decisions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Inside management frame TX status callback, print the TX result where it
was missing. This is useful for debugging management frame drops.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
This adds parsing of non-preferred channel list on an MBO AP. The
information in (Re)Association Request and WNM Notification Request
frames is parsed to get the initial value and updates from each
associated MBO STA. The parsed information is available through the STA
control interface command non_pref_chan[i] rows.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the second memory allocation in ieee802_11_send_wnmsleep_resp() were
to fail and ieee80211_11_get_tfs_ie() succeed, the wnmtfs_ie allocation
would not have been freed on the error path.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While refactoring VLAN comparison into vlan_compare(), it was overlooked
that modifications are needed for tagged VLAN support.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
If WPA2 and MBO are enabled, PMF needs to be enabled in hostapd
configuration. If PMF is optional in the configuration, an MBO STA is
required to negotiate use of PMF.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes hostapd parse a received WNM Notification Request frame
subelements and if a WFA MBO cellular data capability subelement is
seen, update the cellular data capability for the STA.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes hostapd parse the MBO attribute in (Re)Association Request
frame and track the cellular data capability (mbo_cell_capa=<val> in STA
control interface command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This removes multiple copies of wpabuf_resize() following by
wpabuf_put_{buf,data}() with the help of two simple helper functions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add an option to add MBO IE to BSS Transition Management Request frame.
The MBO IE includes the transition reason code, cellular data connection
preference, and, if the disassoc imminent bit is set, it may also
include re-association retry delay. Otherwise, the re-association retry
delay should be set to zero.
The additional BSS_TM_REQ argument uses the following format:
mbo=<reason>:<reassoc delay>:<cell pref>
reason: 0-9
reassoc delay: 0-65535 (seconds; 0 = disabled)
cell pref: 0, 1, 255
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add MBO IE with AP capability attribute to Beacon, Probe Response, and
(Re)Association Response frames to indicate the AP supports MBO.
Add option to add Association Disallowed attribute to Beacon, Probe
Response, and (Re)Association Response frames. Usage:
SET mbo_assoc_disallow <reason code>
Valid reason code values are between 1-5. Setting the reason code to
0 will remove the Association Disallowed attribute from the MBO IE
and will allow new associations.
MBO functionality is enabled by setting "mbo=1" in the config file.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The recent VLAN changes added an explicit code path that sets vlan_desc
= NULL within ap_sta_set_vlan(). This makes some code analyzers warn
about the debug print that could potentially dereference this pointer.
Silence that warning by verifying the pointer more consistently within
this function.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the driver supports 64-bit TX/RX byte counters, use them directly.
The old 32-bit counter extension is maintained for backwards
compatibility with older drivers.
For nl80211 driver interface, the newer NL80211_STA_INFO_RX_BYTES64 and
NL80211_STA_INFO_TX_BYTES64 attributes are used when available. This
resolves the race vulnerable 32-bit value wrap/overflow. Rework RADIUS
accounting to use these for Acct-Input-Octets, Acct-Input-Gigawords,
Acct-Output-Octets, and Acct-Output-Gigawords, these values are often
used for billing purposes.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Previously, stations were added to the driver only after the
(Re)Association Response frame was acked. In the time period between the
station has acked the (Re)Association Response frame and the time the
station was added to the kernel, the station can already start sending
Data frames, which will be dropped by the hardware/driver. In addition
to the data loss, the driver may ignore NDPs with PM bit set from this
STA.
Fix this by setting/adding the STA with associated flag set to the
driver before the AP sends the (Re)Association Response frame with
status success. If the (Re)Association Response frame wasn't acked,
remove the station from the driver.
Note that setting a station to associated state before the non-AP
station acknowledges the (Re)Association Response frame is not compliant
with the IEEE 802.11 standard that specifically states that a non-AP
station should transition to authenticated/associated state only after
it acknowledged the (Re)Association Response frame. However, this is a
justifiable simplification to work around the issue described above since
1. The station will be removed in case it does not acknowledge the
(Re)Association Response frame.
2. All Data frames would be dropped until the station is set to
authorized state and there are no known issues with processing the
other Class 3 frames during the short window before the
acknowledgement is seen.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add support for drivers that support full AP client state, i.e., can
handle adding stations that are not associated yet. For such drivers,
add a station after processing the authentication request, instead of
adding it in the association response callback.
Doing so is beneficial in cases where the driver cannot handle the add
station request, in which case it is useless to perform the complete
connection establishment.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Remove the fallback dependency on os_random() from the code that gets a
valid DFS channel. This is exceptionally unlikely to ever be called as
the call to os_get_random() is unlikely to fail. The intention is to
facilitate future removal of os_random() as it uses a low quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Remove the fallback dependency on os_random() when generating a WPS pin.
This is exceptionally unlikely to ever be called as the call to
os_get_random() is unlikely to fail. The intention is to facilitate
future removal of os_random() as it uses a low quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Do not use the system clock or os_random() that uses a low quality PRNG
as part of the pseudo-random challenge in auth_shared_key(). The
construction can be improved upon by replacing it with a call to
os_get_random(), which uses a high quality PRNG.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Previously, only mesh Action frames from BLOCKED STA were dropped.
Extend that to drop Authentication frames as well.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The SAE PMKID is calculated with IEEE Std 802.11-2012 11.3.5.4, but the
PMKID was re-calculated with 11.6.1.3 and saved into PMKSA cache. Fix
this to save the PMKID calculated with 11.3.5.4 into the PMKSA cache.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Shuffle includes above system ones so to fix a compile issue
on NetBSD where the if_type #define from <net/if.h>
conflicts with the wpa_driver_if_type enum.
Signed-off-by: Roy Marples <roy@marples.name>
This allows the stations to be assigned to their own vif. It does not
need dynamic_vlan to be set. Make hostapd call ap_sta_set_vlan even if
!vlan_desc.notempty, so vlan_id can be assigned regardless.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This makes vlan_newlink() and vlan_dellink() add tagged VLANs to AP_VLAN
interfaces as given by struct vlan_description.
hostapd_vlan_if_remove() is done in vlan_dellink() as tagged interfaces
need to be removed before the interface can be deleted and a DELLINK
message can be generated.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
To prepare for adding tagged VLAN support in vlan_init.c, vlan_newlink()
and vlan_dellink() are split into multiple functions. This reduces
indention and eases adding tagged VLANs as well.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
1. Add tagged VLAN to struct vlan_description
(compile limited number of tagged VLANs per description)
For k tagged VLANs, the first k entries in vlan_description.tagged
are used. They are sorted in ascending order. All other entries are
zero. This way os_memcmp() can find identical configurations.
2. Let tagged VLANs be parsed from RADIUS Access-Accept
3. Print VLAN %d+ with %d=untagged VID if tagged VLANs are set
4. Select an unused vlan_id > 4096 for new tagged VLAN configurations
5. Add EGRESS_VLAN RADIUS attribute parsing also for untagged VLANs
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Separate uplink configuration (IEEE 802.1q VID) and grouping of stations
into AP_VLAN interfaces.
The int vlan_id will continue to identify the AP_VLAN interface the
station should be assigned to. Each AP_VLAN interface corresponds to an
instance of struct hostapd_vlan that is uniquely identified by int
vlan_id within an BSS.
New: Each station and struct hostapd_vlan holds a struct
vlan_description vlan_desc member that describes the uplink
configuration requested. Currently this is just an int untagged IEEE
802.1q VID, but can be extended to tagged VLANs and other settings
easily.
When the station was about to be assigned its vlan_id, vlan_desc and
vlan_id will now be set simultaneously by ap_sta_set_vlan(). So
sta->vlan_id can still be tested for whether the station needs to be
moved to an AP_VLAN interface.
To ease addition of tagged VLAN support, a member notempty is added to
struct vlan_description. Is is set to 1 if an untagged or tagged VLAN
assignment is requested and needs to be validated. The inverted form
allows os_zalloc() to initialize an empty description.
Though not depended on by the code, vlan_id assignment ensures:
* vlan_id = 0 will continue to mean no AP_VLAN interface
* vlan_id < 4096 will continue to mean vlan_id = untagged vlan id
with no per_sta_vif and no extra tagged vlan.
* vlan_id > 4096 will be used for per_sta_vif and/or tagged vlans.
This way struct wpa_group and drivers API do not need to be changed in
order to implement tagged VLANs or per_sta_vif support.
DYNAMIC_VLAN_* will refer to (struct vlan_description).notempty only,
thus grouping of the stations for per_sta_vif can be used with
DYNAMIC_VLAN_DISABLED, but not with CONFIG_NO_VLAN, as struct
hostapd_vlan is still used to manage AP_VLAN interfaces.
MAX_VLAN_ID will be checked in hostapd_vlan_valid and during setup of
VLAN interfaces and refer to IEEE 802.1q VID. VLAN_ID_WILDCARD will
continue to refer to int vlan_id.
Renaming vlan_id to vlan_desc when type changed from int to struct
vlan_description was avoided when vlan_id was also used in a way that
did not depend on its type (for example, when passed to another
function).
Output of "VLAN ID %d" continues to refer to int vlan_id, while "VLAN
%d" will refer to untagged IEEE 802.1q VID.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.
Add a new "pbss" argument to network block. The argument is used
in the following scenarios:
1. When network has mode=2 (AP), when pbss flag is set will start
as a PCP instead of an AP.
2. When network has mode=0 (station), when pbss flag is set will
connect to PCP instead of AP.
The function wpa_scan_res_match() was modified to match BSS according to
the pbss flag in the network block (wpa_ssid structure). When pbss flag
is set it will match only PCPs, and when it is clear it will match only
APs.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
When a mesh point reconnects by starting from Authentication frame
sequence, the plink count was not decremented from its last connection.
This resulted in leaking peer link count and causing wpa_supplicant to
reject the connection after max_peer_links (default: 99) reconnects.
This was reproduced by pre-configuring 2 mesh points with mesh
credentials. Boot both mesh points and make sure they connect to each
other. Then in a loop reboot one of the mesh points after it
successfully connects while leaving the other mesh point up and running.
After 99 iterations the supplicant on mesh point that is not rebooting
will reject the connection request from the other mesh point.
Fix this by decrementing num_plinks when freeing a STA entry that is
still in PLINK_ESTAB state.
Signed-off-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
There is no need to maintain three copies of this functionality even if
it is currently implemented as a single function call.
Signed-off-by: Jouni Malinen <j@w1.fi>
Rework the Acct-Session-Id and Acct-Multi-Session-Id implementation to
give better global and temporal uniqueness. Previously, only 32-bits of
the Acct-Session-Id would contain random data, the other 32-bits would
be incremented. Previously, the Acct-Multi-Session-Id would not use
random data. Switch from two u32 variables to a single u64 for the
Acct-Session-Id and Acct-Multi-Session-Id. Do not increment, this serves
no legitimate purpose. Exclusively use os_get_random() to get quality
random numbers, do not use or mix in the time. Inherently take a
dependency on /dev/urandom working properly therefore. Remove the global
Acct-Session-Id and Acct-Multi-Session-Id values that serve no
legitimate purpose.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
These can get allocated within eapol_auth_alloc(), so it is more logical
to free them in eapol_auth_free() instead of ieee802_1x_free_station()
that ends up calling eapol_auth_free().
Signed-off-by: Jouni Malinen <j@w1.fi>
Event-Timestamp should be sent for all Accounting-Request packets and
only after the system clock has a sane value, not where there's a value
close to the Unix time epoch.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Calculate the required length needed for the extra ANQP elements added
to GAS response buffer instead of using fixed size and truncating the
response if there was not sufficient space.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Acct-Authentic is used to indicate how the user was authenticated and as
such, should not be sent in Accounting-On and Accounting-Off.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Per RFC 2866, 5.10, it is invalid to send Acct-Terminate-Cause in
Accounting-On and Accounting-Off (this is included only when
Acct-Status-Type is set to Stop).
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Ensure that if it is not possible to configure an allowed 20 MHz
channel pair, hostapd falls back to a single 20 MHz channel.
Signed-off-by: Eduardo Abinader <eabinader@ocedo.com>
Number of deployed 80 MHz capable VHT stations that do not support 80+80
and 160 MHz bandwidths seem to misbehave when trying to connect to an AP
that advertises 80+80 or 160 MHz channel bandwidth in the VHT Operation
element. To avoid such issues with deployed devices, modify the design
based on newly proposed IEEE 802.11 standard changes.
This allows poorly implemented VHT 80 MHz stations to connect with the
AP in 80 MHz mode. 80+80 and 160 MHz capable stations need to support
the new workaround mechanism to allow full bandwidth to be used.
However, there are more or less no impacted station with 80+80/160
capability deployed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to follow a debug log from a hostapd process that
manages multiple interfaces.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The ap_sta_deauth_cb and ap_sta_disassoc_cb eloop timeouts are used to
clear a disconnecting STA from the kernel driver if the STA did not ACK
the Deauthentication/Disassociation frame from the AP within two
seconds. However, it was possible for a STA to not ACK such a frame,
e.g., when the disconnection happened due to hostapd pruning old
associations from other BSSes and the STA was not on the old channel
anymore. If that same STA then started a new authentication/association
with the BSS, the two second timeout could trigger during this new
association and result in the STA entry getting removed from the kernel.
Fix this by canceling these eloop timeouts when receiving an indication
of a new authentication or association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
n_chans can have only values 1, 2, or 4 in this function, so the -1 case
could never be reached. Remove the unreachable case to get rid of static
analyzer warnings.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
chan is set to the result of pointer arithmetic (pointer to an entry in
an array) that can never be NULL. As such, there is no need to check for
it to be non-NULL before deference. Remove this check to avoid
complaints from static analyzers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Offloading of ACS to the driver changed the design a bit in a way that
iface->current_mode could actually be NULL when the offloaded ACS
mechanism supports band selection in addition to channel selection. This
resulted in a combination that is too complex for static analyzers to
notice. While acs_init() can be called with iface->current_mode == NULL
that is only in the case where WPA_DRIVER_FLAGS_ACS_OFFLOAD is in use.
In other words, the actual ACS functions like acs_cleanup() that would
dereference iface->current_mode are not used in such a case.
Get rid of static analyzer warnings by explicitly checking
iface->current_mode in acs_init() for the case where ACS offloading is
not used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If P2P support is included in wpa_supplicant build (CONFIG_P2P=y), but
P2P functionality is explicitly disabled (e.g., "P2P_SET disabled 1"),
couple of AP management frame processing steps did not check against
hapd->p2p_group being NULL and could end up dereferencing a NULL pointer
if a Probe Request frame or (Re)Association Request frame was received
with a P2P IE in it. Fix this by skipping these steps if hapd->p2p_group
is NULL.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the Registrar code to generate a Credential with
auth type WPAPSK (i.e., WPA v1) with encr type AES if the Enrollee
claimed support for WPAPSK and not WPA2PSK while the AP was configured
in mixed mode WPAPSK+WPA2PSK regardless of how wpa_pairwise (vs.
rsn_pairwise) was set since encr type was selected from the union of
wpa_pairwise and rsn_pairwise. This could result in the Enrollee
receiving a Credential that it could then not use with the AP.
Fix this by masking the encryption types separately on AP based on the
wpa_pairwise/rsn_pairwise configuration. In the example case described
above, the Credential would get auth=WPAPSK encr=TKIP instead of
auth=WPAPSK encr=AES.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it somewhat easier for the station to be able to receive and
process the encrypted WNM-Notification frames that the AP previously
sentt immediately after receiving EAPOL-Key msg 4/4. While the station
is supposed to have the TK configured for receive before sending out
EAPOL-Key msg 4/4, not many actual implementations do that. As such,
there is a race condition in being able to configure the key at the
station and the AP sending out the first encrypted frame after EAPOL-Key
4/4. The extra 100 ms time here makes it more likely for the station to
have managed to configure the key in time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since hostapd supports ACS now, let's enable its support in
wpa_supplicant as well when starting AP mode.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
[u.oelmann@pengutronix.de: adjusted added text in defconfig]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Let's reuse hostapd code for such handling. This will be useful to get
ACS support into wpa_supplicant where this one needs to handle the
survey event so it fills in the result ACS subsystem will require.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Commit 986de33d5c ('Convert remaining SSID
routines from char* to u8*') started using wpa_ssid_txt() to print out
the SSID for the Called-Station-Id attribute in RADIUS messages. This
was further modified by commit 6bc1f95613
('Use printf escaping in SSID-to-printable-string conversion') to use
printf escaping (though, even without this, wpa_ssid_txt() would have
masked characters).
This is not desired for Called-Station-Id attribute. While it is defined
as a "String", RFC 2865 indicates that "a robust implementation SHOULD
support the field as undistinguished octets.".
Copy the SSID as an array of arbitrary octets into Called-Station-Id to
avoid any kind of masking or escaping behavior. This goes a step further
from the initial implementation by allowing even the possible (but
unlikely in practical use cases) 0x00 octet in the middle of an SSID.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a new hostapd configuration parameter
ocsp_stapling_response_multi that can be used similarly to the existing
ocsp_stapling_response, but for the purpose of providing multiple cached
OCSP responses. This commit adds only the configuration parameter, but
does not yet add support for this mechanism with any of the supported
TLS implementations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the five second timeout was added at the beginning of the
full GAS query and it was not replenished during fragmented exchanges.
This could result in timing out a query if it takes significant time to
go through the possibly multiple fragments and long comeback delay.
Signed-off-by: Jouni Malinen <j@w1.fi>
