Previously, hostapd CHAN_SWITCH command did not effect VHT configuration
for the following:
When VHT is currently disabled (ieee80211ac=0),
1. hostapd_cli -p /var/run/hostapd chan_switch 10 5180 \
sec_channel_offset=1 center_freq1=5190 bandwidth=40 ht
====> Comes up in HT40
2. hostapd_cli -p /var/run/hostapd chan_switch 10 5765 \
sec_channel_offset=-1 center_freq1=5775 bandwidth=40 vht
====> Comes up in HT40
3. hostapd_cli -p /var/run/hostapd chan_switch 10 5200 center_freq1=5200 \
bandwidth=20 vht
====> Comes up in HT20
When VHT is currently enabled (ieee80211ac=1),
1. hostapd_cli -p /var/run/hostapd chan_switch 10 5180 \
sec_channel_offset=1 center_freq1=5190 bandwidth=40 ht
====> Comes up in VHT40
2. hostapd_cli -p /var/run/hostapd chan_switch 10 5200 center_freq1=5200 \
bandwidth=20 ht
====> Comes up in VHT20
This is since VHT config from chan_switch is processed only for
bandwidths 80 and above (80P80, 160) and for VHT20, VHT40 cases, only
NLA chan type and chan width are updated.
There is no NL attribute for determining if it is HT or VHT for
bandwidths 20 & 40 and currently they are updated as HT20, HT40 (+ or -
depending on offset). Same is notified back via
NL80211_CMD_CH_SWITCH_NOTIFY.
Instead of adding new NL attribute for tracking HT/VHT enabled config,
we are adding new hostapd VHT config parameter to save the chan_switch
config and use only for chan_switch case of VHT20 and VHT40.
Tested with all combinations of chan_switch (noHT->20->40->80->) HT/VHT
and confirmed to be working.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
The current EAP peer implementation is not yet ready for the TLS v1.3
changes with EAP-TTLS, EAP-PEAP, and EAP-FAST, so disable TLS v1.3 for
this EAP method for now.
While the current EAP-TLS implementation is more or less complete for
TLS v1.3, there has been no interoperability testing with other
implementations, so disable for by default for now until there has been
chance to confirm that no significant interoperability issues show up
with TLS version update. tls_flags=[ENABLE-TLSv1.3] configuration
parameter can be used to enable TLS v1.3 (assuming the TLS library
supports it; e.g., when using OpenSSL 1.1.1).
Signed-off-by: Jouni Malinen <j@w1.fi>
This may be needed to avoid interoperability issues with the new
protocol version and significant changes for EAP use cases in both key
derivation and handshake termination.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new SQLite table pending_tc is used to maintain a list of sessions
that need to accept Terms and Conditions. This information can be used
on an external Terms and Conditions server to map the incoming MAC
address information into user identity.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow hostapd RADIUS authentication server with SQLite EAP user DB to be
used for testing Terms and Conditions functionality. This could be used
for the HO AAA part of functionality (merging HO AAA and SP AAA into a
single component to avoid separate RADIUS proxy in testing setup).
A T&C server with HTTPS processing is needed to allow this to be used
for full over-the-air testing. This commit adds sufficient functionality
to allow hwsim test cases to cover the RADIUS server part.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd Access-Accept processing to check if the RADIUS
server indicated that Terms and Conditions Acceptance is required. The
new hs20_t_c_server_url parameter is used to specify the server URL
template that the STA is requested to visit.
This commit does not enable any kind of filtering, i.e., only the part
of forwarding a request from Access-Accept to the STA using
WNM-Notification is covered.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd with two new configuration parameters
(hs20_t_c_filename and hs20_t_c_timestamp) that can be used to specify
that the Terms and Conditions attributes are to be added into all
Access-Request messages for Hotspot 2.0 STAs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd Hotspot 2.0 implementation to allow operator icons
to be made available. The existing hs20_icon parameter is used to define
the icons and the new operator_icon parameter (zero or more entries) is
used to specify which of the available icons are operator icons. The
operator icons are advertised in the Operator Icon Metadata ANQP-element
while the icon data can be fetched using the same mechanism (icon
request/binary file) that was added for the OSU Providers icons.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Even with
CONFIG_TLS=gnutls
CONFIG_CRYPTO=gnutls
in .config, nt_password_hash was linked with libcrypto instead of
libgcrypt, which caused linkage failure.
Signed-off-by: Andrey Utkin <andrey_utkin@gentoo.org>
IEEE Std 802.11-2016, 12.7.1.7.1 indicates that the lifetime of the
PMK-R0 (and PMK-R1) is bound to the lifetime of PSK or MSK from which
the key was derived. This is currently stored in r0_key_lifetime, but
cache entries are not actually removed.
This commit uses the r0_key_lifetime configuration parameter when
wpa_auth_derive_ptk_ft() is called. This may need to be extended to use
the MSK lifetime, if provided by an external authentication server, with
some future changes. For PSK, there is no such lifetime, but it also
matters less as FT-PSK can be achieved without inter-AP communication.
The expiration timeout is then passed from R0KH to R1KH. The R1KH verifies
that the given timeout for sanity, it may not exceed the locally configured
r1_max_key_lifetime.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Add a new configuration option ft_r0_key_lifetime that deprecates
r0_key_lifetime. Though, the old configuration is still accepted for
backwards compatibility.
This simplifies testing. All other items are in seconds as well. In
addition, this makes dot11FTR0KeyLifetime comment match with what got
standardized in the end in IEEE Std 802.11r-2008.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The new venue_url parameter can now be used to set the Venue URL ANQP
information instead of having to construct the data and use
anqp_elem=277:<hexdump> to set the raw value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The open file needs to be closed in error case. The conversion to using
a new helper function (hostapd_add_acl_maclist) somehow managed to
remove the neede fclose(f) call. Bring it back to fix this.
Fixes: 3988046de5 ("hostapd: Dynamic MAC ACL management over control interface")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This uses the already existing POLL_STA control interface to poll an
associated station to check connectivity.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
To retain configurator information across hostapd/wpa_supplicant
restart, private key need to be maintained to generate a valid pair of
authentication keys (connector, netaccess_key, csign) for new enrollees
in the network.
Add a DPP_CONFIGURATOR_GET_KEY control interface API through which the
private key of an existing configurator can be fetched.
Command format:
DPP_CONFIGURATOR_GET_KEY <configurator_id>
The output from this command can then be used with
"DPP_CONFIGURATOR_ADD key=<hexdump>" to create the same key again.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This provides an explicit error report if runtime configuration is not
valid and ERP server functionality cannot be used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This header file pulls in an OpenSSL header file and as such, should not
be included without CONFIG_DPP=y to avoid bringing in an unnecessary
build dependency on OpenSSL header files.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, MAC ACL could be modified only through file operations
(modify accept/deny_mac_file and reload it to hostapd). Extend this to
allow MAC ACL to be modified and displayed through new control interface
commands:
ACCEPT_ACL <subcmd> [argument]
DENY_ACL <subcmd> [argument]
subcmd: ADD_MAC <addr>[ VLAN_ID=<id>]|DEL_MAC <addr>|SHOW|CLEAR
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
GnuTLS-based builds can now be done using either libnettle or libgcrypt
for crypto functionality:
CONFIG_TLS=gnutls
CONFIG_CRYPTO=nettle
CONFIG_TLS=gnutls
CONFIG_CRYPTO=gnutls
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace the internal HMAC MD5, SHA-1, and SHA256 implementations with
the ones from libgcrypt and also add the SHA384 and SHA512 versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace the internal SHA256 implementation with the one from libgcrypt
and also add the SHA384 and SHA512 versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf parameter sae_require_pmf=<0/1> can now be used to
enforce negotiation of MFP for all associations that negotiate use of
SAE. This is used in cases where SAE-capable devices are known to be
MFP-capable and the BSS is configured with optional MFP (ieee80211w=1)
for legacy support. The non-SAE stations can connect without MFP while
SAE stations are required to negotiate MFP if sae_require_mfp=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf parameter sae_sync (default: 5) can now be used to
configure the dot11RSNASAESync value to specify the maximum number of
synchronization errors that are allowed to happen prior to
disassociation of the offending SAE peer.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows external programs to get the average channel utilization.
The average channel utilization is calculated and reported through
STATUS command. Users need to configure chan_util_avg_period and
bss_load_update_period in hostapd config to get the average channel
utilization.
Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
Do not update the configuration parameter before having verified the
value to be in the valid range.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that hostapd exposes the DPP_LISTEN and DPP_STOP_LISTEN commands
similarly to wpa_supplicant, expose these through proper hostapd_cli
commands as well to match wpa_cli functionality.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Wpa_supplicant's random pool is not necessary on Android. Randomness
is already provided by the entropymixer service which ensures
sufficient entropy is maintained across reboots. Commit b410eb1913
'Initialize /dev/urandom earlier in boot' seeds /dev/urandom with
that entropy before either wpa_supplicant or hostapd are run.
Signed-off-by: Jeff Vander Stoep <jeffv@google.com>
Configurator signing its own Connector was previously supported only in
wpa_supplicant. This commit extends that to hostapd to allow an AP
acting as a Configurator to self-configure itself.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This moves the Configurator and Bootstrapping Information data from
struct hostapd_data (per-BSS) to struct hapd_interfaces (per-hostapd
process). This allows the information to be maintained over interface
restarts and shared between interfaces.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external applications to get event indication for Probe
Request frames. Extend ctrl iface cmd "ATTACH" to enable this event on
per-request basis. For example, user has to send ctrl iface cmd "ATTACH
probe_rx_events=1" to enable the Probe Request frame events.
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
The new hostapd configuration parameter group_cipher can now be used to
override the automatic cipher selection based on enabled pairwise
ciphers. It should be noted that selecting an unexpected group cipher
can result in interoperability issues and this new capability is mainly
for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this command stopped listen operation immediately, but if
there was an ongoing authentication exchange, a new listen operation was
started. This is not really expected behavior, so stop the
authentication exchange first with this command to avoid restarting
listen operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is an initial step in allowing non-operating channel operations
with DPP when hostapd is the Responder. For now, this is only used for
specifying role=configurator/enrollee and qr=mutual cases similarly to
the wpa_supplicant configuration for in Responder role. Request to use a
non-operating channel will be rejected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Normally, WNM-Sleep Mode exit with management frame protection
negotiated would result in the current GTK/IGTK getting added into the
WNM-Sleep Mode Response frame. Some station implementations may have a
vulnerability that results in GTK/IGTK reinstallation based on this
frame being replayed. Add a new hostapd configuration parameter that can
be used to disable that behavior and use EAPOL-Key frames for GTK/IGTK
update instead. This would likely be only used with
wpa_disable_eapol_key_retries=1 that enables a workaround for similar
issues with EAPOL-Key. This is related to station side vulnerabilities
CVE-2017-13087 and CVE-2017-13088. To enable this AP-side workaround,
set wnm_sleep_mode_no_keys=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
In order to test the WoWLAN GTK rekeying KRACK mitigation, add a
REKEY_GTK hostapd control interface command that can be used at certain
points of the test.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a generic mechanism for configuring the DPP implementation to behave
in particular different (mostly incorrect) ways for protocol testing
purposes. The new dpp_test parameter can be set to a non-zero integer to
indicate a specific behavior. This is only available in
CONFIG_TESTING_OPTIONS=y builds.
This commit include cases for an extra attribute being added after the
Wrapped Data attribute and Initiator/Responder capabilities having an
unexpected zero capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows hostapd testing functionality to be forced to send out a
plaintext EAPOL-Key frame with the RESEND_* command. That can be useful
in seeing how the station behaves if an unencrypted EAPOL frame is
received when TK is already configured.
This is not really perfect since there is no convenient way of sending
out a single unencrypted frame in the current nl80211 design. The
monitor interface could likely still do this, but that's not really
supposed to be used anymore. For now, clear and restore TK during this
operation. The restore part is not really working correctly, though,
since it ends up clearing the TSC value on the AP side and that shows up
as replay protection issues on the station. Anyway, this is sufficient
to generate sniffer captures to analyze station behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a new hostapd configuration parameter
wpa_disable_eapol_key_retries=1 that can be used to disable
retransmission of EAPOL-Key frames that are used to install
keys (EAPOL-Key message 3/4 and group message 1/2). This is
similar to setting wpa_group_update_count=1 and
wpa_pairwise_update_count=1, but with no impact to message 1/4
retries and with extended timeout for messages 4/4 and group
message 2/2 to avoid causing issues with stations that may use
aggressive power saving have very long time in replying to the
EAPOL-Key messages.
This option can be used to work around key reinstallation attacks
on the station (supplicant) side in cases those station devices
cannot be updated for some reason. By removing the
retransmissions the attacker cannot cause key reinstallation with
a delayed frame transmission. This is related to the station side
vulnerabilities CVE-2017-13077, CVE-2017-13078, CVE-2017-13079,
CVE-2017-13080, and CVE-2017-13081.
This workaround might cause interoperability issues and reduced
robustness of key negotiation especially in environments with
heavy traffic load due to the number of attempts to perform the
key exchange is reduced significantly. As such, this workaround
is disabled by default (unless overridden in build
configuration). To enable this, set the parameter to 1.
It is also possible to enable this in the build by default by
adding the following to the build configuration:
CFLAGS += -DDEFAULT_WPA_DISABLE_EAPOL_KEY_RETRIES=1
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface command SET_KEY can be used to request
an arbitrary key to be configured to the driver.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface commands "RESEND_M1 <addr>" and
"RESEND_M3 <addr>" can be used to request a retransmission of the 4-Way
Handshake messages 1/4 and 3/4 witht he same or modified ANonce (in M1).
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface command "RESEND_GROUP_M1 <addr>" can
be used to request a retransmission of the Group Key Handshake message
1/2 for the current GTK.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows ext_mgmt_frame_handling=1 cases with hostapd to process TX
status events based on external processing. This is useful for increased
test coverage of management frame processing.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new sae_password hostapd configuration parameter can now be used to
set the SAE password instead of the previously used wpa_passphrase
parameter. This allows shorter than 8 characters and longer than 63
characters long passwords to be used. In addition, this makes it
possible to configure a BSS with both WPA-PSK and SAE enabled to use
different passphrase/password based on which AKM is selected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
