Check if the device supports specific mandatory features and set the the
relevant WPA_DRIVER_FLAGS_OCE_STA flag. Send the relevant scan
parameters for OCE scans.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Add a flag to scan parameters that enables OCE scan features. If this
flag is set the device should enable the following features as defined
in the Optimized Connectivity Experience Technical Specification v1.0:
- Overwrite FILS request Max Channel Time with actual value (clause 3.8)
- Send Probe Request frame in high rate (at least 5.5 Mbps) (clause 3.12)
- Probe Request frame Transmission Deferral and Suppression (clause 3.5)
- Accept broadcast Probe Response frame (clause 3.6)
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
If you modify the WLAN-STA-AUTHORIZED bit in sta->flags, you have to
call the ap_sta_set_authorized() function to make sure the corresponding
event is sent over the control interface. Otherwise we leak entries in
the event history.
Signed-off-by: Andreas Tobler <andreas.tobler@cloudguard.ch>
When CONFIG_OWE is enabled but none of 11R/11W/FILS are enabled hostapd
(and wpa_supplicant with AP mode support) build failed. Fix this by
adding OWE to the list of conditions for including the local variables.
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
Call to parse_sae_password was incorrectly depending
on CONFIG_TESTING_OPTIONS and CONFIG_SAE. Should
depend only on the latter.
Fixes: 2377c1caef ("SAE: Allow SAE password to be configured separately (AP)")
Signed-off-by: Hai Shalom <haishalom@google.com>
Commit 3f53c006c7 ('nl80211: Ignore
disconnect event in case of locally generated request') made
wpa_supplicant ignore the next received disconnect event for cases where
wpa_supplicant itself requested a disconnection. This can result in
ignoring a disconnection notification in some cases.
Considering a P2P Client receiving disconnect event from the kernel
after a P2P group is started, drv->ignore_next_local_disconnect is
cleared to 0, then wpa_driver_nl80211_disconnect() will be called during
the removal of the group, in which drv->ignore_next_local_disconnect is
set to 1 by mistake.
Do not allow ignore_next_local_{disconnect,deauth} to be set to 1 if the
driver is not in associated state (drv->associated is 0) to avoid this
type of cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This enhances DPP_AUTH_INIT, DPP_CONFIGURATOR_SIGN, and SET
dpp_configurator_params to allow optional setting of the DPP groupId
string for a Connector. If the value is not set, the previously wildcard
value ("*") is used by default.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The payload used for the existing NAN vendor command,
QCA_NL80211_VENDOR_SUBCMD_NAN is a binary blob of data. This
command is not extendable to send additional information. Hence
define a new vendor command QCA_NL80211_VENDOR_SUBCMD_NAN_EXT,
that can carry the binary blob encapsulated within an attribute
and can carry additional attributes to enhance the NAN command
interface. Define additional 3 new attributes for conveying
type of NAN subcmd and channel information.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Present implementation of NAN vendor command does not use
attribute encapsulation for sending the command from userspace
to the driver, payload is directly sent as is. Attribute
QCA_WLAN_VENDOR_ATTR_NAN is used only for receiving vendor
events in the userspace from the driver. Update the doc as per
this implementation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The max supported ADDBA buffer size value is 256, so change
the buffer size attribute type to U16 to configure the testbed
device to use the 256 buffer size in ADDBA negotiation in 11ax
testing.
This attribute is used only to configure a testbed device and the old
definition of this attribute was not used in any deployed implementation
hence it is still justifiable to change the definition.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_BLACKLIST_BSSID to get maximum
blacklist BSSIDs capability from the driver for gscan.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The WDS-STA-INTERFACE-ADDED/WDS-STA-INTERFACE-REMOVED events were always
sent to the first BSS instead of the specific BSS that the STA was
connected to in multi-BSS cases. Fix this by using the BSS specific
context pointer.
Fixes: 1952b626ba ("hostapd: Add ctrl iface indications for WDS STA interface")
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
If the RADIUS authentication server dropped the cached ERP keys for any
reason, FILS authentication attempts with ERP fails and the previous
wpa_supplicant implementation ended up trying to use the same keys for
all consecutive attempts as well. This did not allow recovery from state
mismatch between the ERP server and peer using full EAP authentication.
Address this by trying to use full (non-FILS) authentication when trying
to connect to an AP using the same ERP realm with FILS-enabled network
profile if the previous authentication attempt had failed. This allows
new ERP keys to be established and FILS authentication to be used again
for the consecutive connections.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
GCM-AES-256 cipher suite is defined in IEEE Std 802.1AEbn-2011.
If authenticator configured as GCM-AES-256, the distributed SAK will be
256 bits indicated by the GCM-AES-256 ID in the MKA packet.
This patch will make AES Key Unwrap to 32 bytes of SAK when identify the
ID.
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
'hostapd_cli SET ht_capab' only checked for [HT40+] or [HT40-] or both
to be present. Based on the offset + or -, secondary_channel is updated
but HT20/VHT20 mode can be brought up only from config file and can't be
done using the SET command when the current HT mode is HT40+ or HT40-.
When managing AP+STA mode from userspace doing hostapd_cli: "disable ->
set channel, ht_capab -> enable" sequence, channel switch from
HT40/VHT40 to HT20/VHT20 was not possible with this SET ht_capab
limitation.
Cover this additional case by resetting secondary_channel to 0 for
HT20/VHT20 when ht_capab has neither [HT40+] nor [HT40-] present.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
This allows WEP mode AP to be re-enabled automatically after external
ifconfig down + up on netdev used by hostapd.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Fix the typo in using WPA_DRIVER_FLAGS_QOS_MAPPING to set the QoS Map
bit in Extended Capabilities. The previous implementation ended up
adding this bit even if the driver did not actually indicate support for
the capability.
Signed-off-by: Jouke Witteveen <j.witteveen@gmail.com>
SSL_session_reused() is the same as the deprecated SSL_cache_hit(). The
engine load stuff is now handled by OPENSSL_init().
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Make it clear that the consideration should be only for the IBSS case
and in infrastructure BSS case, PMKID KDE should not be added due to
risks involved with exposing this to stations that do not know the
passphrase.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Ignore unauthenticated encrypted EAPOL-Key data in supplicant
processing. When using WPA2, these are frames that have the Encrypted
flag set, but not the MIC flag.
When using WPA2, EAPOL-Key frames that had the Encrypted flag set but
not the MIC flag, had their data field decrypted without first verifying
the MIC. In case the data field was encrypted using RC4 (i.e., when
negotiating TKIP as the pairwise cipher), this meant that
unauthenticated but decrypted data would then be processed. An adversary
could abuse this as a decryption oracle to recover sensitive information
in the data field of EAPOL-Key messages (e.g., the group key).
(CVE-2018-14526)
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Verify that the automatically generated network profile is able to
connect to a non-FT network automatically after having used FT for the
first connection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This node was mapped to a SET_CRED roaming_consortium command with
quotation marks even though this is a hexdump of the OI. Remove the
quotation marks to allow this to be set correctly in the wpa_supplicant
credential.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that EAP-AKA' client rejects Challenge with an appended AT_KDF
and a modified AT_KDF value during KDF negotiation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Clarify that proto=RSN is used for WPA3 and add the WPA3-Personal name
for SAE and include OWE as a possible key_mgmt value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Clarify that wpa=2 (i.e., RSN) is used for WPA3 and list previously
undocumented wpa_key_mgmt values.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new test config QCA vendor attribute to override the MU EDCA
parameters to default values in the driver for test configuration. This
is used for configuring the testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When OSEN is used in the BSS that is shared both for production data and
OSU uses, the group cipher might be either GTK_NOT_USED (like in Rel 2
OSEN) or CCMP. Modify hs20-osu-client to allow both these group ciphers
to be used when requesting OSEN connection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check that the @1@ macro gets replaced correctly both when in the middle
and when in the end of the URL template.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The last character of the STA MAC address got replaced with 0x00 due to
truncation if the @1@ macro was used at the end of the URL. Fix this
case by allocating larger buffer for the URL.
Fixes: d4e39c51f8 ("HS 2.0: Move Terms and Conditions Server URL generation from AP to AS")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure HE
trigger frame MAC padding duration value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
ifname is checked for interface down event in commit
106fa1e97e ("nl80211: Indicate
interface-down event only for the main netdev"). Do the same for
interface up event to avoid unexpected notifications when the master
interface (e.g., a bridge interface) is set up while then WLAN interface
remains down.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When we start hostapd having Hotspot 2.0 configuration with interface
already added to bridge interface, addition and deletion of new neighbor
to bridge ip neighbor table fails.
This is since 'bss->added_if_into_bridge' is not set which only allows
'drv->rtnl_sk' (nl_sock for NETLINK_ROUTE) allocation needed for bridge
ip neighbor table.
Add a new bit 'already_in_bridge' and set it when interface is already
added to bridge by some external component. Check this bit in addition
to 'bss->added_if_into_bridge' for 'drv->rtnl_sk' allocation done in
i802_init().
Now 'drv->rtnl_sk' is closed in wpa_driver_nl80211_deinit() regardless of
'bss->added_if_into_bridge' since when we have 'bss->already_in_bridge'
case too, this need to be removed.
brctl show
bridge name bridge id STP enabled interfaces
br0 8000.8efdf006b050 no ap
hostapd_cli raw STATUS-DRIVER
Selected interface 'ap'
ifindex=15
ifname=ap
brname=br0
addr=8e:fd:f0:06:b0:50
freq=5180
beacon_set=1
already_in_bridge=1
..
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Since the generic DFS offload support flag is added as
NL80211_EXT_FEATURE_DFS_OFFLOAD, only use the vendor command to check
DFS capablity if the flag is not already set.
Signed-off-by: Peng Xu <pxu@codeaurora.org>
Add a new wifi test config QCA vendor attributes to configure
HE MU EDCA parameters value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure Tx
beamformee number of space-time streams value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends the terms.php implementation of Hotspot 2.0 Terms and
Conditions server to allow it to interact with hostapd(AS) to clear the
filtering rules from the AP. After requesting hostapd to send out the
CoA-Request, terms.php waits for up to 10 seconds to see whether the
current_sessions table gets an update to indicate that filtering has
been successfully disabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new DAC_REQUEST control interface command can now be used to request
hostapd to send out Disconnect-Request and CoA-Request packets for an
existing session.
DAC_REQUEST <disconnect|coa> <MAC Address> [t_c_clear]
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
