Extend verify_channel() to return whether IR is allowed on the channel
or not, and make it a global function so it can be used in other files,
too. This makes this function useful for checking not only if a channel
is supported but also if it is allowed for active and passive scan.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The length of a Measurement Report frame should be limited by the
maximum allowed MMPDU size (IEEE Std 802.11-2016, 9.6.2.3). Enforce this
size limit, and in case the report elements are longer than the allowed
size, split them between several MPDUs.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Supported Operating Classes element and its use is define in the IEEE
802.11 standard and can be sent even when MBO is disabled in the build.
As such, move this functionality out from the CONFIG_MBO=y only mbo.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes wpa_supplicant behavior more consistent with FLUSH command to
clear all state. Previously, it was possible for an ongoing scan to be
aborted when the FLUSH command is issued and the scan results from that
aborted scan would still be processed and that would update the BSS
table which was supposed to cleared by the FLUSH command.
This could result in hwsim test case failures due to unexpected BSS
table entries being present after the FLUSH command.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit enhances the existing implementation of abort scan to also
abort concurrent active vendor scans. This is achieved by passing the
the scan_cookie to the driver interface with the intention to abort
the specific scan request. This scan_cookie is returned from the driver
interface when the scan request is scheduled.
This scan_cookie is 0 if the scan is triggered through the upstream
cfg80211 interface. Thus, the scan_cookie is used to determine whether
to abort the cfg80211 or vendor scan request.
Also, the previous implementation of relying on scan_work/p2p_scan_work
for the active work to trigger the abort scan is enhanced to check for
the started state of either of these work operations. This should also
help to abort the concurrent active scan/p2p-scan operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This provides more details on BSS selection process in the debug log.
Previously, the BSSs that were not either the current or the selected
one were not necessarily printed at all. Now all BSSs that match the
currently selected network are listed with their frequency and signal
strength details.
Signed-off-by: Jouni Malinen <j@w1.fi>
When scheduled scan stops without the interface request (for example,
driver stopped it unexpectedly), start a regular scan to continue
scanning for networks and avoid being left with no scan at all.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
This extends ANQP_GET command to support querying MBO cellular
preference also. The cellular preference can be requested along with
neigbor report by appending mbo:1 to the command arguments.
For example:
ANQP_GET <bssid> 272,mbo:1
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The reason detail field in non_pref_chan attribute was removed from MBO
draft v0.0_r25, so the STA should not include this field to be compliant
with the latest draft.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
For testing purposes, it is useful to have an option to be able to
reject BTM Request sent by AP in order to verify the AP behavior upon
BTM Request rejection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a testing mechanism to allow association disallowed set by AP to be
ignored. This can be used to verify AP behavior for disallowing a
specific association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Implement "SET ignore_auth_resp <0/1>" command to simulate auth/assoc
response loss and EAPOL RX packet loss by ignoring corresponding
incoming events.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
All the 3 control interfaces: socket based, dbus & binder needs to
perform the same sequence of steps for network add/remove. So, move
these to a common utility method in |wpa_supplicant.c| instead of
duplicating the code everywhere.
Signed-off-by: Roshan Pius <rpius@google.com>
Move out the disconnect command handling from |ctrl_iface.c| to
|wpa_supplicant.c| so that it can be reused across the different
control interfaces (socket, dbus & binder).
Signed-off-by: Roshan Pius <rpius@google.com>
This allows P2P Listen to be offloaded to device to enhance power
saving.
To start P2P listen offload, from wpa_cli interface, issue the command:
p2p_lo_start <freq> <period> <interval> <count>
To stop P2P listen offload, issue the command:
p2p_lo_stop
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Handle radio measurement request that contains LCI request. Send
measurement report based on a configurable LCI report element. The LCI
report element is configured over the control interface with
SET lci <hexdump of the element>
and cleared with
SET lci ""
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add an option to request LCI and Location Civic Measurement in Neighbor
Report Request frame, as described in IEEE P802.11-REVmc/D5.0, 9.6.7.6.
Note: This changes the encoding format of the NEIGHBOR_REP_REQUEST
ssid=<val> parameter. This used to be parsed as raw SSID data which is
problematic for accepting additional parameters. The new encoding allows
either a string within double-quotation marks or a hexdump of the raw
SSID.
Thew new format:
NEIGHBOR_REP_REQUEST [ssid=<SSID>] [lci] [civic]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a function that parses SSID in text or hex format. In case of the
text format, the SSID is enclosed in double quotes. In case of the hex
format, the SSID must include only hex digits and not be enclosed in
double quotes. The input string may include other arguments after the
SSID.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
This commit implements the methods defined in Supplicant service:
1. CreateInterface
2. RemoveInterface
3. GetInterface
The binder service returns the corresponding iface binder object
references which can be used by clients to control a specific
interface.
Signed-off-by: Roshan Pius <rpius@google.com>
Create the skeletal binder interface for wpa_supplicant. The interface
hierarchy is based off the existing dbus
interface(https://w1.fi/wpa_supplicant/devel/dbus.html).
Since we use libbinder, the binder interface codebase needs to be
written in C++ and can only be compiled on Android platform for now.
The aidl files define binder RPC interfaces. The Android build system
generates the corresponding C++ interface classes which needs to be
implemented by the server process.
The clients can obtain a reference to the binder service (root object)
using:
android::String16 service_name("fi.w1.wpa_supplicant");
android::sp<android::IBinder> binder =
android::defaultServiceManager()->getService(service_name);
Once a reference to the root object is retrieved, the clients can
obtain references to other RPC objects using that root object methods.
Signed-off-by: Roshan Pius <rpius@google.com>
This allows the SME-in-the-driver case to get similar information about
reassociation that was already available for the SME-in-wpa_supplicant
case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant command line argument -M can be used to describe
matching rules with a wildcard interface name (e.g., "wlan*").
This is very useful for systems without udev (Linux) or devd (FreeBSD).
Signed-off-by: Roy Marples <roy@marples.name>
Previously, BLOCKED state duration slightly increased up to 3600. Though
the BLOCKED state could be canceled by ap_handle_timer(). Because the
timer timeouts in ap_max_inactivity(default=300sec) and remove STA
objects (the object retains BLOCKED state).
This patch re-designs my commit bf51f4f82b
('mesh: Fix remaining BLOCKED state after SAE auth failure') to replace
mesh_auth_block_duration by ap_max_inactivity and remove incremental
duration.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
(Re)Association Response frame with status code other than 0 is now
notified over DBUS as a part of PropertiesChanged signal. This can be
used by application in case AP is denying association with status code
17 (band steering) so that it does not interfere in the BSSID selection
logic of wpa_supplicant.
Signed-off-by: Naveen Singh <nasingh@google.com>
Expose the functions wpas_get_bands() and wpas_freq_to_band() and the
enum wpa_radio_work_band, since they will be needed outside
wpa_supplicant.c.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
In many places in the code there was a reference to wpa_s->parent to get
from group interface to p2p_dev interface. These places can break if
P2P_DEVICE interface would need to be used with the primary interface as
the group interface, since the parent of the primary interface points to
itself and not the p2p_dev interface.
Fix this by adding a separate "p2pdev" pointer to wpa_supplicant,
it will be the same as parent pointer in most cases but whenever
the primary interface is used as a group interface, change it to
point to the correct p2p_dev interface.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
If the BSS Transition Management Request frame includes only a single
candidate and we need to scan for the BSS to get up-to-date information,
use a scan for the known BSSID instead of wildcard BSSID. In addition,
set the SSID in the scan if it is known based on old scan results in the
BSS table. This removes unnecessary Probe Response frames when we are
interested in results from only a single BSS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add the transition candidate list to BSS Transition Management Response
frame. The candidates preference is set using the regular wpa_supplicant
BSS selection logic. If the BSS transition request is rejected and
updated scan results are not available, the list is not added.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When rejecting a BSS Transition Management Request frame, add MBO IE to
the BSS Transition Management Response frame to specify the transition
rejection reason.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add parsing of MBO IE in BSS Transition Management Request frames. If
the MBO IE includes the association retry delay attribute, do not try to
reconnect to the current BSS until the delay time is over.
If the MBO IE includes the cellular data connection preference attribute
or the transition rejection reason attribute, send a message to upper
layers with the data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Prevent association to MBO APs that have association disallowed
attribute in MBO IE in Beacon or Probe Response frames.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add cellular capability attribute to MBO IE and add MBO IE with cellular
capabilities to Probe Request frames. By default, cellular capability
value is set to Not Cellular capable (3).
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Send a WNM-Notification Request frame with Non-preferred Channel Report
subelement if the non-preferred channels list changes during an
association.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
This adds a new command based Hotspot 2.0 icon retrieval option.
In short, here is the new command sequence:
1. REQ_HS20_ICON <bssid> <file-name>
2. event: RX-HS20-ICON <bssid> <file-name> <size>
3. GET_HS20_ICON <bssid> <file-name> <offset> <size>
(if needed, repeat with larger offset values until full icon is
fetched)
5. DEL_HS20_ICON <bssid> <file-name>
REQ_HS20_ICON is a new command that is analogous to HS20_ICON_REQUEST
with the slight difference that an entry to store the icon in memory is
prepared. The RX-HS20-ICON event has been augmented with BSSID,
file-name and size, and GET_HS20_ICON is used to retrieve a chunk of up
to <size> bytes of icon data at offset <offset>. Each chunk is returned
as a base64 encoded fragment, preceded by "HS20-ICON-DATA", BSSID, and
file-name as well as the starting offset of the data.
If there is no entry prepared for the icon when the ANQP result comes
back, hs20_process_icon_binary_file falls back to legacy behavior.
Finally the DEL_HS20_ICON command deletes (all) icons associated with
BSSID and file-name (there could be several if retries are used and they
have different dialog tokens).
Signed-off-by: Jan Nordqvist <jannq@google.com>
The new methods are
1. VendorElemAdd "i" "ay" i=integer ay=array of bytes
2. VendorElemGet "i" i=integer (output array of bytes)
3. VendorElemRem "i" "ay" i=integer ay=array of bytes
These provide functionality similar to the control interface commands
VENDOR_ELEM_ADD, VENDOR_ELEM_GET, and VENDOR_ELEM_REMOVE.
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Purushottam Kushwaha <p.kushwaha@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
Signed-off-by: Dilshad Ahmad <dilshad.a@samsung.com>
[VendorElemGet to return array of bytes instead of string; cleanup]
Signed-off-by: Jouni Malinen <j@w1.fi>
Add the option to configure scheduled scan plans in the config file.
Each scan plan specifies the interval between scans and the number
of scan iterations. The last plan will run infinitely and thus
specifies only the interval between scan iterations.
usage:
sched_scan_plans=<interval:iterations> <interval2:iterations2> ... <interval>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
The new max_oper_chwidth and freq2 arguments to P2P_CONNECT, P2P_INVITE,
and P2P_GROUP_ADD control interface commands can be used to request
larger VHT operating channel bandwidth to be used than the previously
used maximum 80 MHz.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Mesh Points themselves have capability to support VHT as long as
hardware supports it. However, supporting VHT in mesh mode was disabled
because no one had clearly tested and confirmed its functionality. Since
VHT80 has now been verified to work with ath10k QCA988X driver and
mac80211_hwsim, enable VHT support in mesh mode.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
The AP is not expected to send out a WNM-Sleep Mode Response frame
without the STA trying to use WNM-Sleep Mode. Drop such unexpected
responses to reduce unnecessary processing of the frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
On successful P2P PD, report the chosen frequency in case the local
device is going to be the P2P GO, so in can later be used to instantiate
the new P2P GO, etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This commit contains the necessary changes to parallelize
distinct radio work operations which are different in type and
the band used, only when the underlying driver is capable of
supporting such simultaneous offchannel operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P group is not yet operating when going through invitation
exchange for re-invocation. Previously, an old cached scan result could
be used to skip the scan immediately after the invitation exchange.
While this may result in the fastest possible connection, it does have
some issues with cases where the GO takes some time to start up. It
would also be at least theoretically possible for some of the BSS
parameters to be different, so having a fresh scan result from the new
GO instance may be desired in any case.
Add a mechanism to skip scan results that have been last updated before
a specific point in time and as the first user for this mechanism,
require chan results to be more recent than the invitation message
exchange for the P2P Client role in persistent group re-invocation case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When P2PS PD with default P2PS method is done, the peer that becomes GO
should authorize the client. However, P2PS specification doesn't require
the client to include its intended interface address in PD
Request/Response. As a result, the P2P Client's interface address may not
be known and any address may need to be authorized.
Previously, client's P2P Device Address was used for authorization,
which is not correct when a dedicated interface is used for P2P Client.
This is not resulting in a connection failure, however it causes a
significant delay (until WPS_PIN_TIME_IGNORE_SEL_REG elapses). Fix this
by authorizing the intended interface address, if known; or any address,
if not known.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This buffer is owned by the FST module, so mark it const in the
set_ies() callback to make it clearer which component is responsible for
modifying and freeing this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P configuration file is wrongly set as STA configuration file,
even though a separate configuration file is mentioned with '-m' option.
Add initialization and deallocation of global.params->conf_p2p_dev to
fix this.
Signed-off-by: Gautam <gautams@broadcom.com>
Add vendor command to pass SET setband command to the driver and read
the updated channel list from driver when this notification succeeds.
This allows the driver to update its internal channel lists based on
setband configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In case of a network interface removal, check if the interface
was also the parent interface of the P2P Device dedicated interface.
If this is the case, then stop the P2P Device functionality, and
remove the P2P Device dedicated interface.
In case that the interface is added again and P2P Device
functionality can be enabled again, add a new P2P Device dedicated
interface and allow further P2P Device functionality.
In case that the P2P Device dedicated interface is re-created, the
original P2P Device configuration file is needed, so store it in
the global params (instead in the wpa_interface configuration).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
PBC overlap detection searches for another BSS with active PBC in the
BSS table. However, when a separate P2P interface is used, scan results
without P2P IE are not saved in the BSS table, so non-P2P BSS's with
active PBC will not be detected.
Fix this by iterating only the WPS AP array instead of the BSS table.
This is also more efficient since only WPS APs may have active PBC. This
also fixes hwsim test "grpform_pbc_overlap" when a dedicated P2P Device
is used.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
1. Add global p2p_cli_probe property to enable/disable Probe Request
frame RX reporting for connected P2P Clients. The property can be set to
0 - disable or 1 - enable. The default value is 0.
2. Enable Probe Request frame RX reporting for P2P Client on
WPA_COMPLETED state if p2p_cli_probe property is set to 1. Disable it
when an interface state is changing to any other state.
3. Don't cancel Probe Request frame RX reporting on wpa_stop_listen for
a connected P2P Client handling Probe Request frames.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Support a request to scan specific SSIDs given by user with the SCAN
command. The SSID list can be suffixed to the scan command as follows.
For example, if SSIDs "ABC" and "abc123" need to be specifically
scanned, the command should be "SCAN ssid 414243 ssid 616263313233". The
value of the SSID is passed in hexadecimal representation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
D-Bus used the p2p_dev member in struct wpa_supplicant to track the
interface used for P2P Device operations. However, this is not needed as
the interface used for P2P Device operations is stored in struct
wpa_global->p2p_init_wpa_s.
Replace all the redirections to wpa_s->p2p_dev with redirections to
wpa_s->global->p2p_init_wpa_s and removed this member as it is no
longer needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Commit c2762e410f ('P2P: Update D-Bus
network object semantics during group formation') added this helper
function to determine whether a network block is used for storing a
persistent group information. However, it implemented this in a way that
matches both persistent group storage and an operating persist group
instance. This does not seem to match the expected behavior for the
D-Bus objects, so fix this to match only the persistent group storage
case to avoid registering/unregistered incorrect D-Bus objects for
groups.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
Previously, wpa_supplicant was using number of scan iterations
(WPS_PIN_SCAN_IGNORE_SEL_REG = 3) to give some time for finding a WPS AP
with Selected Registrar TRUE before starting to iterate through all WPS
APs. While this works fine in most cases, some drivers may return the
initial three scan results so quickly that the total amount of time is
only couple of seconds in case none of the APs are initially advertising
Selected Registrar TRUE. To give some more time for APs (WPS Registrars)
to become ready, add an additional constraint on the iteration based on
time (WPS_PIN_TIME_IGNORE_SEL_REG = 5 seconds).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend interface_add and interface_remove commands via an optional
argument to allow wpa_supplicant to create/delete a new virtual
interface.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
If all networks are temporarily disabled, delay AP selection until at
least one network is enabled. Running AP selection when all networks are
disabled is useless as wpa_supplicant will not try to connect. In
addition, it will result in needless scan iterations that may delay the
connection when it is needed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
wpa_supplicant_deinit_iface() ends up removing all P2P groups if the
removed interface is the parent interface. This is correct behavior in
general, but this resulted in issues in the new group interface
initialization error path since wpa_s->parent was not assigned before
hitting this check. Fix this by assigning wpa_s->parent as part of
wpa_supplicant_add_iface().
Signed-off-by: Jouni Malinen <j@w1.fi>
There are number of cases where wpa_supplicant requests the current
connection to be disconnected before starting a new operation. Such
cases do not really indicate that there was an error in connecting or a
disconnection initiated by the AP, so do not add a temporary blacklist
entry in such sequences.
Signed-off-by: Jouni Malinen <j@w1.fi>
This modifies the BSS selection routines to calculate SNR and estimated
throughput for each scan result and then use the estimated throughput as
a criteria for sorting the results. This extends the earlier design by
taking into account higher throughput rates if both the AP and local
device supports HT20, HT40, or VHT80. In addition, the maximum rate is
restricted based on SNR.
In practice, this gives significantly higher probability of selecting
HT/VHT APs when there are multiple BSSes in the same ESS and SNR is not
low enough to prevent higher MCS use.
Signed-off-by: Jouni Malinen <j@w1.fi>
When SAE authentication fails, wpa_supplicant retries four times. If all
the retries result in failure, SAE state machine enters BLOCKED state.
Once it enters this state, wpa_supplicant doesn't retry connection. This
commit allow connection retries even if the state machine entered
BLOCKED state.
There could be an opinion "Is this patch needed? User could know the SAE
state machine is in the BLOCKED mode by MESH-SAE-AUTH-BLOCKED event.
Then user can retry connection. By user action, SAE state machine can
change the state from BLOCKED to another.". Yes, this is a true at the
joining mesh STA. However, a STA that is already a member of existing
mesh BSS should not retry connection because if the joining mesh STA
used wrong password, all the existing STA should do something from UI to
retry connection.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The pending interface created during provision discovery should
not be removed on stopping p2p_find. This pending interface has
to be used after completing GO negotiation. Earlier the pending
interface is created just before GO negotiation so there was no
problem.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If P2PS config method is used for provisioning, upon forming a new GO,
start WPS registrar for the provisioned peer automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This introduces a P2P module callback function that will be used to
create the pending P2PS group after sending PD Response and receiving
ACK status for it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpas_p2p_prov_disc() implementation to accept P2PS
parameters. None of the callers are yet using this functionality; the
following commit introduces a user.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Connection with a PMF enabled AP will fail if we try to negotiate PMF
while the local driver does not support this. Since pmf=1 does not
require PMF for a successful connection, it can be ignored in such a
case to avoid connectivity issues with invalid configuration. This makes
it somewhat easier to allow upper layer programs to use pmf=1 default
regardless of driver capabilities.
Signed-off-by: Jouni Malinen <j@w1.fi>
external_scan_running should be common to all interfaces that share a
radio. This fixes a case where external_scan_running was set on a single
interface, but did not block scan on other interfaces.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
This restores some of the pre-radio work behavior for scanning by
retrying scan trigger if the driver rejects it (most likely returning
EBUSY in case of nl80211-drivers). Retry is indicated in the
CTRL-EVENT-SCAN-FAILED event with "retry=1".
For manual scans (e.g., triggered through "SCAN" control interface
command), no additional retries are performed. In other words, if upper
layers want to retry, they can do so based on the CTRL-EVENT-SCAN-FAILED
event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
For CONFIG_TESTING_OPTIONS=y builds, add a new test parameter than can
be used to trigger various error cases within wpa_supplicant operations
to make it easier to test error path processing. "SET test_failure
<val>" is used to set which operation fails. For now, 0 = no failures
and 1 = scan trigger fails with EBUSY. More operations can be added in
the future to extend coverage.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for interworking_find_network_match() to find a possible
BSS match in a case where more thorough checks in
wpa_supplicant_select_bss() reject network. This itself is fine, in
general, but when combined with wpa_supplicant_fast_associate()
optimization and auto_interworking=1, this resulted in a busy loop of up
to five seconds and a possible stack overflow due to recursion in that
loop.
Fix this by limiting the Interworking wpa_supplicant_fast_associate()
call to be used only once per scan iteration, so that new scan
operations can be completed before going through the scan results again.
Signed-off-by: Jouni Malinen <j@w1.fi>
Automatically enable HT20, HT40+, HT40-, or VHT, based on driver
capabilities. This obsoletes the mesh_ht_mode network block parameter
that was previously used to configure HT parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
1. Supported MAC address randomization for scan.
2. Supported MAC address randomization for scheduled scan.
2. Supported MAC address randomization for pno.
4. Add functions to set and clear the MAC address randomization
state variables.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The specification requires the tspecs to be kept upon reassociation to
the same BSS. Save the last tspecs before such reassociation, and
reconfigure on the association notification.
Note that the current flow is not transparent to the user
(it is notified about deauth/reassoc and tspec removal/addition).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Include only the potentially affected channel range in OBSS scans to
reduce the amount of offchannel time needed for scanning when requested
by the AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.
This command makes a virtual mesh interface to be used for mesh gate.
This command expects to be used like this.
wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Externally triggered scan could result in a new radio work item getting
started even when external radio work was in progress. Delay such start
until the external work is completed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Allow supplying an SSID for the SSID IE. If not supplied, no SSID IE is
sent, and the request implies the current SSID.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Add the ability to send a Neighbor Report Request (part of
RRM). Requester is then notified once the report arrives.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
When the list of preferred transition candidates is received, use the
identified channels to optimize the following scan so that no time is
wasted on other channels.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add the TSPEC to the driver on successful TSPEC ADDTS response. Delete
the TSPEC when receiving DELTS action.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Add basic implementation for ADDTS and DELTS sending
functions.
wpas_wmm_ac_addts() will send ADDTS request public action,
containing TSPEC (traffic stream specification) with
the given params.
wpas_wmm_ac_delts() will look for the saved tspec with
the given tid, and send DELTS public action for it.
(Handling of ADDTS response and actually configuring the admission
control params will be added in following patches.)
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Add add_tx_ts() and del_tx_ts() ops to notify the driver about
TSPEC add / delete.
Additionally, add wmm_ac_supported flag to indicate
whether the driver supports WMM AC.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Initialize WMM AC data structures upon successful association
with an AP that publishes WMM support, and deinitialize the data
structure when the association is no longer valid.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
It is possible for scan result processing or BSS entry removal to occur
while there is a pending connect or sme-connect radio work with a
previously selected BSS entry. The BSS pointer was previously verified
to be valid, i.e., still point to a BSS entry, at the time the actual
connection operation is started. However, that BSS entry could have
changed to point to another BSS if the old BSS entry was either removed
or reallocated and a new BSS entry was added at the same location in
memory. This could result in the connection attempt failing to configure
parameters properly due to different BSS information (e.g., different
BSSID).
Fix this by updated the pending connect radio work data on BSS entry
updates similarly to how the last_scan_res array was updated. If the
selected BSS entry is removed, this will still result in a failed
connection, but reallocated BSS entry is now followed properly and used
when the connection work starts.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This will be useful to hand-off P2P commands from the parent interface
to its dedicated P2P device if that one is present, in DBus interface.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Once a P2P GO interface is configured, save the group common
frequencies, as this can be useful later for channel selection
considerations during channel switch, etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The extra_roc_dur parameter can now be used in CONFIG_TESTING_OPTIONS=y
builds to simulate driver behavior where the ROC duration gets increased
without user space request.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add routines to (de)initialize mesh interface data structures and
join and leave mesh networks.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
Add smps_modes field, and let the driver fill it with its supported SMPS
modes (static/dynamic). This will let us start an AP with specific SMPS
mode (e.g., dynamic) that will allow it to reduce its power usage.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Commit 1595eb93ae ('P2P: Add support for
60 GHz social channel') had an unintended change to how P2P search scans
2.4 GHz social channels. Use of p2p_supported_freq() to filter the list
of social channels ended up using the disallow_freq setting to remove
social channels from the P2P search scans. This is not desired since
peers need to be found on any of the social channels even if those
channels have been disabled from P2P operating channel use. Restore the
previous behavior by included all the 2.4 GHz social channels in P2P
search scans if the driver indicated support for the 2.4 GHz band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is now possible to run hwsim_test like data connectivity test through
wpa_supplicant/hostapd control interface if CONFIG_TESTING_OPTIONS=y is
used for the build. Test functionality is enabled/disabled at runtime
with "DATA_TEST_CONFIG <1/0>". The "DATA_TEST_TX <dst> <src> <tos>"
command can be used to request a test frame to be transmitted.
"DATA-TEST-RX <dst> <src>" event is generated when the test frame is
received.
Signed-off-by: Jouni Malinen <j@w1.fi>
Convert the driver flags variable to u64 since there was no room for
more flags.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
This makes wpa_supplicant SME create PMKSA cache entries from SAE
authentication and try to use PMKSA caching if an entry is found for the
AP. If the AP rejects the attempt, fall back to SAE authentication is
used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new ext_eapol_frame_io parameter can be used to configure hostapd
and wpa_supplicant to use control interface for receiving and
transmitting EAPOL frames. This makes it easier to implement automated
test cases for protocol testing. This functionality is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A P2P Client may be able to connect to the GO even if the WPS
provisioning step has not terminated cleanly (e.g., P2P Client does not
send WSC_Done). Such group formation attempt missed the event
notification about started group on the GO and also did not set the
internal state corresponding to the successful group formation.
This commit addresses the missing part by completing GO side group
formation on a successful first data connection if WPS does not complete
cleanly. Also, this commit reorders the STA authorization indications to
ensure that the group formation success notification is given prior to
the first STA connection to handle such scenarios.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the case of non-netdev P2P management device ended up
pulling in both the main interface (e.g., wlan0) and P2P Device
interface (from command line -m argument) as configuration. Similarly,
the main interface ended up included both configuration files. This is
not really helpful for various use cases, e.g., when permanent P2P group
information is stored in the P2P Devince interface, but it gets
duplicated in the main station interface configuration.
Clean this up by changing the -m<file> argument to replace, not
concatenate, configuration information. In other words, the main station
interface will not read this configuration and the P2P Device interface
(non-netdev) does not read parameters from the station interface
configuration file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
mac_addr=2 and preassoc_mac_addr=2 parameters can now be used to
configure random MAC address to be generated by maintaining the OUI part
of the permanent MAC address (but with locally administered bit set to
1). Other than that, these values result in similar behavior with
mac_addr=1 and preassoc_mac_addr=1, respectively.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.
This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.
This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.
The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some deployed APs send two credentials when in mixed-WPA/WPA2
configuration; one for the WPA-Personal/TKIP and the other for
WPA2-Personal/CCMP. Previously, this would result in two network blocks
getting added for the single AP. This can be somewhat confusing and
unnecessary, so merge such credentials into a single one that allows
both WPA and WPA2 to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds following new control interface commands to allow arbitrary
vendor elements to be added into number of frames:
VENDOR_ELEM_ADD <frame id> <hexdump of elem(s)>
VENDOR_ELEM_GET <frame id>
VENDOR_ELEM_REMOVE <frame id> <hexdump of elem(s)>
VENDOR_ELEM_REMOVE <frame id> *
The following frames are supported in this commit (additional frames can
be added in the future):
0 = Probe Request frame in P2P device discovery
1 = Probe Response frame from P2P Device role
2 = Probe Response frame from P2P GO
3 = Beacon frame from P2P GO
4 = PD Req
5 = PD Resp
6 = GO Neg Req
7 = GO Neg Resp
8 = GO Neg Conf
9 = Invitation Request
10 = Invitation Response
11 = P2P Association Request
12 = P2P Association Response
One or more vendor element can be added/removed with the commands. The
hexdump of the element(s) needs to contain the full element (id, len,
payload) and the buffer needs to pass IE parsing requirements to be
accepted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new "scan_id=<comma separated list of network ids>" parameter can
now be used to specify a list of network ids that have scan_ssid=1 to
indicate active scanning of the SSID. This adds the listed SSIDs to the
scan command to allow manual scan requests to perform active scans for
hidden SSIDs. For example, "SCAN scan_id=1,7,11" would run a scan with
the SSID fetched from the configured network blocks 1, 7, and 11
(assuming those are set with scan_ssid=1). The SSIDs will be included
even from network blocks that are currently disabled.
The maximum number of SSIDs added to the request is limited by the
driver support. If more than supported values are specified, the command
will fail (returns "FAIL").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to trigger new SA Query procedure to check the state of
the connection immediately after having performed such a check. Limit
the impact of burst of unprotected Deauth/Disassoc frames by starting a
new SA Query procedure only once at least 10 seconds has passed from the
previous SA Query that was triggered by reception of an unprotected
disconnection. The first SA Query procedure for each association does
not follow this rule to avoid issues with test cases that expect to see
an SA Query every time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When the number of frequencies supported by the kernel is bigger than
one, and there is a need to pick a frequency for a new flow such as P2P
GO Negotiation or P2P Invitation, the flow should be able to pick the
best frequency among all the frequencies currently used by the device.
In order to prioritize between the currently used frequencies, add
the ability to collect additional data about each used frequency
(if the frequency is used by a station interface or P2P Client)
and when needed select the best frequency, where:
1. Infrastructure interfaces have highest priority
2. P2P Client interfaces have higher priority over AP/GO
interfaces.
The rational is that the frequency of an AP/GO can change while
that of a station interface cannot.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Prepare for new extended capabilities bits by checking that the local
buffer is large enough to contain all the bits the driver requests. The
existing buffers are large enough to include anything defined until now,
but it would be possible to add more definitions in the future, so
increase them a bit as well to make this more future proof.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the offchannel TX frame command was offloaded to the driver in
offchannel_send_action(), we must not send another copy of the frame if
a remain-on-channel event happens to be delivered between this TX
command and the matching TX status event. It was possible for the
duplicated frame to cause problems, e.g., with P2P invitation exchange
if the same Invitation Request frame got sent twice and only the first
one getting accepted by the peer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Scan for GO on the negotiated operating channel for few iterations
before searching on all the supported channels during persistent group
reinvocation. In addition, use the already known SSID of the group in
the scans. These optimizations reduce group formation time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add "reattach" command to perform single-channel single-ssid scan
instead of full scan when trying to reconnect to the currently
"connected" network (assuming old scan results are not current enough to
skip the scan completely). This allows the scan result to come back in
much faster time. In ath9k, the scan took around 12 seconds with full
background scan, and only 0.1 second with the single-channel single-ssid
scan. Thus, take much less time for the client to re-establish
connection with the currently "connected" network.
Signed-hostap: Peter Qiu <zqiu@chromium.org>
This enables more convenient protocol testing of AP and P2P
functionality in various error cases and unexpected sequences without
having to implement each test scenario within wpa_supplicant.
ext_mgmt_frame_handle parameter can be set to 1 to move all management
frame processing into an external program through control interface
events (MGMT-RX and MGMT-TX-STATUS) and command (MGMT_TX). This is
similar to the test interface that was added to hostapd previously, but
allows more control on offchannel operations and more direct integration
with the internal P2P module.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add an option to specify a configuration file that can be used to hold
the P2P_DEVICE configuration parameters. If this option is not used, the
P2P_DEVICE configuration parameters will be read from interface
configuration file.
Note that it is advised to use this option in some cases such as:
If a P2P_DEVICE is supported by the driver, the wpa_supplicant creates a
dedicated P2P Device interface, where the configuration file used for
the main interface is used. As a consequence, if the configuration file
includes network definition etc., the wpa_supplicant will try to perform
station specific flows on the P2P Device interface which will fail.
If a P2P_DEVICE is supported by the driver and update_config is used,
the P2P Device configuration data will override the main interface
configuration data.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Scan operation is not that reliable, so try couple of times if no
OSU provider matches are found during fetch_osu command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_cli fetch_osu command can be used to fetch information about
all OSU providers and write that to a text file with the icons in
separate files. cancel_osu_fetch command can be used to stop ongoing OSU
provider list fetch.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, any network block could be used to select the BSS to connect
to when processing scan results after Interworking network selection.
This can result in somewhat unexpected network selection in cases where
credential preferences indicated that a specific network was selected,
but another network ended up getting used for the connection. While the
older networks continue to be valid, add special processing for this
initial post-interworking-connect case to get more consistent network
selection to match with the Interworking network selection result.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the connect or sme-connect radio work to get
re-scheduled while an earlier request was still pending, e.g.,
select_network is issued at the moment a scan radio work is in progress
and the old scan results are recent enough for starting the connection.
This could result in unexpected attempt to re-associate immediately
after completing the first connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While testing rfkill blocking of a scanning interface, it
was seen that the ongoing scan never completes. This happens
since EVENT_SCAN_RESULTS is discarded on a disabled interface.
Fix this and also other possible radio work completion issues
by removing all the radio works (including started) of the
disabled interface.
To be able to remove already started radio works, make their
callbacks be reentrant with deinit flag (when the work
is started), so each radio work should be able to handle
its own termination.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Commit bd3a373767 added a mechanism to use
AP Channel attribute from within a Credential attribute to optimize
scans. However, this design is not actually used with the WPS NFC use
cases. With configuration token, the AP Channel attribute is in the same
container with the Credential attribute (and that was also handled in
the previous implementation). With connection handover, AP Channel
information is outside the Credential attribute as well.
Simplify implementation by removing the AP Channel within Credential
case. This allows wpas_wps_use_cred() to get the AP Channel from the
container instead of having to find this during credential iteration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This new mechanism allows P2P Client to request an IPv4 address from the
GO as part of the 4-way handshake to avoid use of DHCP exchange after
4-way handshake. If the new mechanism is used, the assigned IP address
is shown in the P2P-GROUP-STARTED event on the client side with
following new parameters: ip_addr, ip_mask, go_ip_addr. The assigned IP
address is included in the AP-STA-CONNECTED event on the GO side as a
new ip_addr parameter. The IP address is valid for the duration of the
association.
The IP address pool for this new mechanism is configured as global
wpa_supplicant configuration file parameters ip_addr_go, ip_addr_mask,
ip_addr_star, ip_addr_end. For example:
ip_addr_go=192.168.42.1
ip_addr_mask=255.255.255.0
ip_addr_start=192.168.42.2
ip_addr_end=192.168.42.100
DHCP mechanism is expected to be enabled at the same time to support P2P
Devices that do not use the new mechanism. The easiest way of managing
the IP addresses is by splitting the IP address range into two parts and
assign a separate range for wpa_supplicant and DHCP server.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The device with the NFC Tag can be configured to enable NFC to be used
with "P2P_SET nfc_tag 1" and "P2P_LISTEN" commands to allow static
handover to be used.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"NFC_REPORT_HANDOVER {INIT,RESP} P2P <req> <sel>" can now be used to
report completed NFC negotiated connection handover in which the P2P
alternative carrier was selected.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a QCA vendor specific nl80211 event to allow the driver to
indicate a list of frequency ranges that should be avoided due to
interference or possible known co-existance constraints. Such
frequencies are marked as not allowed for P2P use to force groups to be
formed on different channels.
If a P2P GO is operating on a channel that the driver recommended not to
use, a notification about this is sent on the control interface and
upper layer code may decide to tear down the group and optionally
restart it on another channel. As a TODO item, this could also be changed
to use CSA to avoid removing the group.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When start PNO request comes from control interface, wpa_supplicant
should wait until ongoing sched_scan (triggered by wpa_supplicant)
gets cancelled. Issuing cancel sched_scan and start PNO scan
one after another from pno_start() would lead wpa_supplicant to clear
wps->sched_scanning flag while getting sched_scan stopped event
from driver for cancel sched_scan request. In fact, PNO scan will
be in progress in driver and wpa_s->sched_scanning will not be set
in such cases.
In addition to this change, RSSI threshold limit is passed as part of
start sched_scan request. This was previously set only in pno_start(),
but the same parameter should be available for generic sched_scan calls
as well and this can now be reached through the new PNO start sequence.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If we already know the SSID of the P2P group we are trying to join, use
that SSID to limit scan responses and BSS selection since we do not
really look for any other network in this case. In addition, this can
fix cases where the peer has just changed its SSID (e.g., started a new
group) and there may be multiple BSS entries for the same BSSID.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some EAP methods can go through a step that is expected to fail and as
such, should not trigger temporary network disabling when processing
EAP-Failure or deauthentication. EAP-WSC for WPS was already handled as
a special case, but similar behavior is needed for EAP-FAST with
unauthenticated provisioning.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no need to wait for the 15 second group formation timeout to
clear the state if WPS failure is detected during P2P group formation.
Allow the WPS exchange steps (WSC_NACK and EAP-Failure) to be completed
and remove the group to get rid of the extra wait.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, only the last response data was kept in memory. This
increases that to hold up to two last responses to allow some more
parallel operations to be requested. In addition, the response data is
now freed as soon as the external program has fetched it.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new control interface command RADIO_WORK can be used by external
programs to request radio allocation slots from wpa_supplicant if
exclusive radio control is needed, e.g., for offchannel operations. If
such operations are done directly to the driver, wpa_supplicant may not
have enough information to avoid conflicting operations. This new
command can be used to provide enough information and radio scheduling
to avoid issues with such cases.
Signed-hostap: Jouni Malinen <j@w1.fi>
If an external program triggers a scan, wpa_supplicant does not have a
wpa_radio work item for this operation to protect against other
offchannel operations. This can result in operations failing, so try to
avoid damage by not starting any new wpa_radio work items during a scan
that was started by another process.
Signed-hostap: Jouni Malinen <j@w1.fi>
