This makes it easier to integrate dynamic VLANs in custom network
configurations. The bridge name is added after the interface name in the
vlan_file line, also separated by whitespace.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The purpose of Multi-AP specification is to enable inter-operability
across Wi-Fi access points (APs) from different vendors.
This patch introduces one new configuration parameter 'multi_ap' to
enable Multi-AP functionality and to configure the BSS as a backhaul
and/or fronthaul BSS.
Advertise vendor specific Multi-AP capabilities in (Re)Association
Response frame, if Multi-AP functionality is enabled through the
configuration parameter.
A backhaul AP must support receiving both 3addr and 4addr frames from a
backhaul STA, so create a VLAN for it just like is done for WDS, i.e.,
by calling hostapd_set_wds_sta(). Since Multi-AP requires WPA2 (never
WEP), we can safely call hostapd_set_wds_encryption() as well and we can
reuse the entire WDS condition.
To parse the Multi-AP Extension subelement, we use get_ie(): even though
that function is meant for parsing IEs, it works for subelements.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This adds support for hostapd-as-RADIUS-authentication-server to request
subscription remediation for SIM-based credentials. The new hostapd.conf
parameter hs20_sim_provisioning_url is used to set the URL prefix for
the remediation server for SIM provisioning. The random
hotspot2dot0-mobile-identifier-hash value will be added to the end of
this URL prefix and the same value is stored in a new SQLite database
table sim_provisioning for the subscription server implementation to
use.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new hostapd configuration parameter hs20_release can be used to
configure the AP to advertise a specific Hotspot 2.0 release number
instead of the latest supported release. This is mainly for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support for negotiating WNM Collocated Interference Reporting. This
allows hostapd to request associated STAs to report their collocated
interference information and wpa_supplicant to process such request and
reporting. The actual values (Collocated Interference Report Elements)
are out of scope of hostapd and wpa_supplicant, i.e., external
components are expected to generated and process these.
For hostapd/AP, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration. STAs are requested to perform
reporting with "COLOC_INTF_REQ <addr> <Automatic Report Enabled> <Report
Timeout>" control interface command. The received reports are indicated
as control interface events "COLOC-INTF-REPORT <addr> <dialog token>
<hexdump of report elements>".
For wpa_supplicant/STA, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration and setting Collocated
Interference Report Elements as a hexdump with "SET coloc_intf_elems
<hexdump>" control interface command. The hexdump can contain one or
more Collocated Interference Report Elements (each including the
information element header). For additional testing purposes, received
requests are reported with "COLOC-INTF-REQ <dialog token> <automatic
report enabled> <report timeout>" control interface events and
unsolicited reports can be sent with "COLOC_INTF_REPORT <hexdump>".
This commit adds support for reporting changes in the collocated
interference (Automatic Report Enabled == 1 and partial 3), but not for
periodic reports (2 and other part of 3).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend hostapd to allow the new OSU Provider NAI List ANQP-element to be
advertised in addition to the previously used OSU Providers list
ANQP-element. The new osu_nai2 configurator parameter option is used to
specify the OSU_NAI value for the shared BSS (Single SSID) case while
osu_nai remains to be used for the separate OSU BSS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Call to parse_sae_password was incorrectly depending
on CONFIG_TESTING_OPTIONS and CONFIG_SAE. Should
depend only on the latter.
Fixes: 2377c1caef ("SAE: Allow SAE password to be configured separately (AP)")
Signed-off-by: Hai Shalom <haishalom@google.com>
'hostapd_cli SET ht_capab' only checked for [HT40+] or [HT40-] or both
to be present. Based on the offset + or -, secondary_channel is updated
but HT20/VHT20 mode can be brought up only from config file and can't be
done using the SET command when the current HT mode is HT40+ or HT40-.
When managing AP+STA mode from userspace doing hostapd_cli: "disable ->
set channel, ht_capab -> enable" sequence, channel switch from
HT40/VHT40 to HT20/VHT20 was not possible with this SET ht_capab
limitation.
Cover this additional case by resetting secondary_channel to 0 for
HT20/VHT20 when ht_capab has neither [HT40+] nor [HT40-] present.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
This allows a single BSS/SSID to be used for both data connection and
OSU. Instead of hostapd configuration osen=1, wpa_key_mgmt=OSEN (or more
likely, wpa_key_mgmt=WPA-EAP OSEN) is used to enable this new option.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These changes add support for salted password databases to EAP-pwd per
RFC 8146. This commits introduces the framework for enabling this and
the salting mechanisms based on SHA-1, SHA256, and SHA512 hash
algorithms.
Signed-off-by: Dan Harkins <dharkins@lounge.org>
This extends the SAE implementation in both infrastructure and mesh BSS
cases to allow an optional Password Identifier to be used. This uses the
mechanism added in P802.11REVmd/D1.0. The Password Identifier is
configured in a wpa_supplicant network profile as a new string parameter
sae_password_id. In hostapd configuration, the existing sae_password
parameter has been extended to allow the password identifier (and also a
peer MAC address) to be set. In addition, multiple sae_password entries
can now be provided to hostapd to allow multiple per-peer and
per-identifier passwords to be set.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The current EAP peer implementation is not yet ready for the TLS v1.3
changes with EAP-TTLS, EAP-PEAP, and EAP-FAST, so disable TLS v1.3 for
this EAP method for now.
While the current EAP-TLS implementation is more or less complete for
TLS v1.3, there has been no interoperability testing with other
implementations, so disable for by default for now until there has been
chance to confirm that no significant interoperability issues show up
with TLS version update. tls_flags=[ENABLE-TLSv1.3] configuration
parameter can be used to enable TLS v1.3 (assuming the TLS library
supports it; e.g., when using OpenSSL 1.1.1).
Signed-off-by: Jouni Malinen <j@w1.fi>
This may be needed to avoid interoperability issues with the new
protocol version and significant changes for EAP use cases in both key
derivation and handshake termination.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends hostapd Access-Accept processing to check if the RADIUS
server indicated that Terms and Conditions Acceptance is required. The
new hs20_t_c_server_url parameter is used to specify the server URL
template that the STA is requested to visit.
This commit does not enable any kind of filtering, i.e., only the part
of forwarding a request from Access-Accept to the STA using
WNM-Notification is covered.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd with two new configuration parameters
(hs20_t_c_filename and hs20_t_c_timestamp) that can be used to specify
that the Terms and Conditions attributes are to be added into all
Access-Request messages for Hotspot 2.0 STAs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd Hotspot 2.0 implementation to allow operator icons
to be made available. The existing hs20_icon parameter is used to define
the icons and the new operator_icon parameter (zero or more entries) is
used to specify which of the available icons are operator icons. The
operator icons are advertised in the Operator Icon Metadata ANQP-element
while the icon data can be fetched using the same mechanism (icon
request/binary file) that was added for the OSU Providers icons.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE Std 802.11-2016, 12.7.1.7.1 indicates that the lifetime of the
PMK-R0 (and PMK-R1) is bound to the lifetime of PSK or MSK from which
the key was derived. This is currently stored in r0_key_lifetime, but
cache entries are not actually removed.
This commit uses the r0_key_lifetime configuration parameter when
wpa_auth_derive_ptk_ft() is called. This may need to be extended to use
the MSK lifetime, if provided by an external authentication server, with
some future changes. For PSK, there is no such lifetime, but it also
matters less as FT-PSK can be achieved without inter-AP communication.
The expiration timeout is then passed from R0KH to R1KH. The R1KH verifies
that the given timeout for sanity, it may not exceed the locally configured
r1_max_key_lifetime.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Add a new configuration option ft_r0_key_lifetime that deprecates
r0_key_lifetime. Though, the old configuration is still accepted for
backwards compatibility.
This simplifies testing. All other items are in seconds as well. In
addition, this makes dot11FTR0KeyLifetime comment match with what got
standardized in the end in IEEE Std 802.11r-2008.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The new venue_url parameter can now be used to set the Venue URL ANQP
information instead of having to construct the data and use
anqp_elem=277:<hexdump> to set the raw value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The open file needs to be closed in error case. The conversion to using
a new helper function (hostapd_add_acl_maclist) somehow managed to
remove the neede fclose(f) call. Bring it back to fix this.
Fixes: 3988046de5 ("hostapd: Dynamic MAC ACL management over control interface")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This provides an explicit error report if runtime configuration is not
valid and ERP server functionality cannot be used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, MAC ACL could be modified only through file operations
(modify accept/deny_mac_file and reload it to hostapd). Extend this to
allow MAC ACL to be modified and displayed through new control interface
commands:
ACCEPT_ACL <subcmd> [argument]
DENY_ACL <subcmd> [argument]
subcmd: ADD_MAC <addr>[ VLAN_ID=<id>]|DEL_MAC <addr>|SHOW|CLEAR
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
The new hostapd.conf parameter sae_require_pmf=<0/1> can now be used to
enforce negotiation of MFP for all associations that negotiate use of
SAE. This is used in cases where SAE-capable devices are known to be
MFP-capable and the BSS is configured with optional MFP (ieee80211w=1)
for legacy support. The non-SAE stations can connect without MFP while
SAE stations are required to negotiate MFP if sae_require_mfp=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf parameter sae_sync (default: 5) can now be used to
configure the dot11RSNASAESync value to specify the maximum number of
synchronization errors that are allowed to happen prior to
disassociation of the offending SAE peer.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows external programs to get the average channel utilization.
The average channel utilization is calculated and reported through
STATUS command. Users need to configure chan_util_avg_period and
bss_load_update_period in hostapd config to get the average channel
utilization.
Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
Do not update the configuration parameter before having verified the
value to be in the valid range.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd configuration parameter group_cipher can now be used to
override the automatic cipher selection based on enabled pairwise
ciphers. It should be noted that selecting an unexpected group cipher
can result in interoperability issues and this new capability is mainly
for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Normally, WNM-Sleep Mode exit with management frame protection
negotiated would result in the current GTK/IGTK getting added into the
WNM-Sleep Mode Response frame. Some station implementations may have a
vulnerability that results in GTK/IGTK reinstallation based on this
frame being replayed. Add a new hostapd configuration parameter that can
be used to disable that behavior and use EAPOL-Key frames for GTK/IGTK
update instead. This would likely be only used with
wpa_disable_eapol_key_retries=1 that enables a workaround for similar
issues with EAPOL-Key. This is related to station side vulnerabilities
CVE-2017-13087 and CVE-2017-13088. To enable this AP-side workaround,
set wnm_sleep_mode_no_keys=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a new hostapd configuration parameter
wpa_disable_eapol_key_retries=1 that can be used to disable
retransmission of EAPOL-Key frames that are used to install
keys (EAPOL-Key message 3/4 and group message 1/2). This is
similar to setting wpa_group_update_count=1 and
wpa_pairwise_update_count=1, but with no impact to message 1/4
retries and with extended timeout for messages 4/4 and group
message 2/2 to avoid causing issues with stations that may use
aggressive power saving have very long time in replying to the
EAPOL-Key messages.
This option can be used to work around key reinstallation attacks
on the station (supplicant) side in cases those station devices
cannot be updated for some reason. By removing the
retransmissions the attacker cannot cause key reinstallation with
a delayed frame transmission. This is related to the station side
vulnerabilities CVE-2017-13077, CVE-2017-13078, CVE-2017-13079,
CVE-2017-13080, and CVE-2017-13081.
This workaround might cause interoperability issues and reduced
robustness of key negotiation especially in environments with
heavy traffic load due to the number of attempts to perform the
key exchange is reduced significantly. As such, this workaround
is disabled by default (unless overridden in build
configuration). To enable this, set the parameter to 1.
It is also possible to enable this in the build by default by
adding the following to the build configuration:
CFLAGS += -DDEFAULT_WPA_DISABLE_EAPOL_KEY_RETRIES=1
Signed-off-by: Jouni Malinen <j@w1.fi>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new sae_password hostapd configuration parameter can now be used to
set the SAE password instead of the previously used wpa_passphrase
parameter. This allows shorter than 8 characters and longer than 63
characters long passwords to be used. In addition, this makes it
possible to configure a BSS with both WPA-PSK and SAE enabled to use
different passphrase/password based on which AKM is selected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd configuration parameter owe_groups can be used to
specify a subset of the allowed DH groups as a space separated list of
group identifiers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The owe_transition_bssid and owe_transition_ssid parameters can now be
replace with owe_transition_ifname to clone the BSSID/SSID information
automatically in case the same hostapd process manages both the OWE and
open BSS for transition mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new owe_transition_bssid and owe_transition_ssid parameters can be
used to configure hostapd to advertise the OWE Transition Mode element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The hostapd.conf tls_flags=[SUITEB-NO-ECDH] and wpa_supplicant network
profile phase1="tls_suiteb_no_ecdh=1" can now be used to configure Suite
B RSA constraints with ECDHE disabled. This is mainly to allow
the DHE TLS cipher suite to be tested.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new sae_commit_override=<hexdump> parameter can be used to force
hostapd to override SAE commit message fields for testing purposes. This
is included only in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow hostapd to be configured to perform SAE reflection attack for SAE
testing purposes with sae_reflection_attack=1 configuration parameter.
This is included only in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd allows arbitrary AP PIN to be used in WPS. This means that
setting ap_pin to a zero length string ends up enabling AP PIN so that
external registrars can use this specific zero lenth ap_pin value. There
are apparently some APs that have used this invalid configuration with
unintended results. While the proper fix for that is to fix the
component that generates the invalid configuration, hostapd can also
reject such values since the likelihood of a real world use case for
zero length AP PIN (Device Password) is minimal.
Start interpreting zero length ap_pin parameter value as a request to
"unset" the previously set value in hostapd.conf (or if not previously
set, leave it unset). With this, a hostapd.conf file including the
"ap_pin=" line will end up getting interpretted just like that same file
with the ap_pin parameter completely removed, i.e., with AP PIN being
disabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, CONFIG_WNM enabled build that supports WNM for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode WNM is required and there is no need for AP mode WNM.
Add support to differentiate between station mode WNM and AP mode
WNM in wpa_supplicant builds by adding CONFIG_WNM_AP that should be
used when AP mode WNM support is required in addition to station mode
WNM. This allows binary size to be reduced for builds that require
only the station side WNM functionality.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add OCE IE in Beacon, Probe Response, and (Re)Association Response
frames if OCE is enabled in the configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The default value for GTK rekeying period was previously hardcoded to
600 seconds for all cases. Leave that short value only for TKIP as group
cipher while moving to the IEEE 802.11 default value of 86400 seconds
(once-per-day) for CCMP/GCMP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend hostapd configuration to include parameters needed for the DPP
AKM: dpp_connector, dpp_netaccesskey, dpp_netaccesskey_expiry,
dpp_csign, dpp_csign_expiry.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new acs_exclude_dfs=1 parameter can be used to request hostapd to
exclude all DFS channels from ACS consideration. This is mainly of use
for cases where the driver supports DFS channels, but for some reason a
non-DFS channel is desired when using automatic channel selection.
Previously, the chanlist parameter could have been used for this, but
that required listing all the acceptable channels. The new parameter
allows this to be done without such a list.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
