This reverts commit bf700cc3d2. The
concurrent initialization test case is now expected to work again with
the STA entry added early enough to avoid the recently added mac80211
validation step failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
Older mac80211 implementations did not set the link identifier
appropriately, resulting in an incorrect teardown packet being sent the
peer. wpa_supplicant adds the FTE containing the MIC field calculated
using the correct link-identifier. This causes a MIC failure on the
other side and the teardown is discarded. Verify this case is fixed by
newer kernel and wpa_supplicant code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Relying on qos qosinfo is not enough, as it can be 0 for WMM enabled
peers that don't support U-APSD. Further, some peers don't even contain
this IE (Google Nexus 5), but do contain the WMM IE during setup.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
A recent mac80211 patch ("8f02e6b mac80211: make sure TDLS peer STA
exists during setup") forces the TDLS STA to exist before sending any
mgmt packets. Add the STA before sending a concurrent-setup test packet.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Some drivers need to know the initiator of a TDLS connection in order
to generate a correct TDLS mgmt packet. It is used to determine
the link identifier IE. Pass this information to the driver.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Commit 97ed9a06df ('nl80211: Remove bridge
FDB entry upon sta_remove()') used nl_sock and nl_socket_* functions
which are not compatible with older versions of libnl. Fix this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
IEEE 802.11 standard sends AID in a field that is defined in a bit
strange way to set two MSBs to ones. That is not the real AID and those
extra bits need to be filtered from the value before passing this to the
driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
mac_addr=2 and preassoc_mac_addr=2 parameters can now be used to
configure random MAC address to be generated by maintaining the OUI part
of the permanent MAC address (but with locally administered bit set to
1). Other than that, these values result in similar behavior with
mac_addr=1 and preassoc_mac_addr=1, respectively.
Signed-off-by: Jouni Malinen <j@w1.fi>
random_mac_addr_keep_oui() is similar to random_mac_addr(), but it
maintains the OUI part of the source address.
Signed-off-by: Jouni Malinen <j@w1.fi>
The FDB entry removal ensures that the traffic destined for a
disassociated station's MAC address is no longer forwarded from the
bridge to the BSS.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Support 60 GHz band in P2P module by selecting random social channel
from all supported social channels in 2.4 GHz and 60 GHz bands.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In case P2P is not enabled the if (dev_addr) is always ignored as
dev_addr will be NULL. As this code is relevant only to P2P, it can be
moved to be the ifdef to avoid static analyzer warnings. (CID 72907)
Signed-off-by: Philippe De Swert <philippe.deswert@jollamobile.com>
This permits to set or unset the WiFi Display subelements from DBus, by
providing the full WFD specific IE frame.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
'\e' representing ESC (0x1b) is not C standard, it's an GNU extension.
https://gcc.gnu.org/onlinedocs/gcc/Character-Escapes.html#Character-Escapes
Since the code also compiles on Windows with Microsoft compiler, we
should use '\033' instead.
Note: I didn't try to build the whole wpa_supplicant on Windows, so I
don't know if it still builds (I have no Visual Studio 2005 for a quick
test). I just needed the string conversion routines for the P"" syntax
in both directions.
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Remove and re-start the persistent group manually to increase test
coverage to include the case of re-configuring the PSK list entries from
a stored persistent group.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the previuous test case used a non-RSN AP and that was left in
cfg80211 scan results, it was possible for ap_hs20_random_mac_addr to
pick that old AP from the previous test and reject to connect through
Hotspot 2.0 mechanisms. Work around this test issue by requesting new
set of scan result at the beginning of the test.
Signed-off-by: Jouni Malinen <j@w1.fi>
If "STA_AUTOCONNECT 0" has been used to disable automatic connection on
disconnection event and the driver indicates multiple disconnection
events for the disconnection from the current AP when WPS is started, it
could have been possible to hit a case where wpa_s->disconnected was set
to 1 during WPS processing and the following scan result processing
would stop the operation.
wpa_s->key_mgmt == WPA_KEY_MGMT_WPS check was trying to avoid to skip
autoconnect when WPS was in use, but that does not seem to work anymore.
Fix this by checking through wpas_wps_searching() as well to avoid
setting wpa_s->disconnect = 1 when there is an ongoing WPS operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
This check is already being done on wpas_p2p_deinit_iface.
Of course, it is assumed wpa_s is not deinit when reaches
that point as a matter of fact.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
As P2P service are not necessarily attached to a iface, when
added, proceed with same approach on p2p global deinit. Such
approach solves memory leaks ocurring upon wpa_supplicant
termination, when p2p services were registered previously.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
The sd_pending_bcast_queries variable should be decremented only
in case of success. This way, the supplicant can retry if a service
discovery request fails.
Signed-off-by: Constantin Musca <constantin.musca@intel.com>
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.
This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.
This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.
The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.
Signed-off-by: Jouni Malinen <j@w1.fi>
The scan for WPS-AUTH validation may miss a Probe Response frame if the
hostapd process gets blocked under load, e.g., when testing with
parallel-vm.sh.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the p2p_go_neg_start timeout handler to get called
when there was a pending timeout from an earlier GO Negotiation start.
This could result in that old timeout expiring too early for the newly
started GO Negotiation to complete. Avoid such issues by setting a
sufficiently long timeout here just before triggering the new GO
Negotiation.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, it was possible for the p2p->pending_listen_freq to be left
at non-zero value if Probe Request frame was received from a peer with
which we were waiting to start GO Negotiation/Invite process. That could
result in the following Listen operation getting blocked in some
operation sequences if the peer did not acknowledge the following P2P
Public Action frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, extra connect/roam events were ignored when user space SME
was used to avoid confusing double events for association. However,
there was no matching code for ignoring auth/assoc events when using
driver SME. Such events would not normally show up since the driver SME
case would not generated them. However, when testing forced connect
command with force_connect_cmd=1 driver param, these events are
indicated.
Ignore the extra events in testing cases to make the hwsim test cases
match more closely the real code path for driver SME. In addition, this
resolves some test case failures where double association event could
end up causing a failure, e.g., when doing PMKSA caching in
pmksa_cache_oppurtunistic_connect.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, periodic autoscan could have been left running and that
could result in the following test cases failing in some cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some of the test cases where using INTERWORKING_SELECT internally
without using scan_for_bss like the helper functions did. Add explicit
scan_for_bss calls to make the test cases less likely to fail due to
missing BSSes in scan results. This could cause false failure reports
when runnign under heavy load with parallel-vm.sh.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids unexpected connection attempts in cases a matching network
is enabled and there is no existing connection (e.g., when testing with
ENABLE_NETWORK no-connect option).
Signed-off-by: Jouni Malinen <j@w1.fi>
A mac80211 TDLS validation change ended up breaking test functionality
that was needed for this test case. Instead of reporting this known
issue as a FAIL every time, mark the test as SKIP since the issues is
known and there are no plans of "fixing" it.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends "wpa_cli -a<action script>" functionality to work with the
global wpa_supplicant control interface. The IFNAME=<ifname> prefix is
removed from the event messages and converted to the control interface
name when present. Previously, action scripts could only be used with
the per-interface control interfaces.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Number of other buffers were already increased to this size, but the
buffer used for receiving unsolicited event messages from wpa_supplicant
(e.g., for wpa_cli action scripts) was still at the older 256 byte size.
This could result in some events getting truncated. Avoid this by using
the same 4096 byte buffer size here as in the other places receiving
messages from wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
