external_scan_running should be common to all interfaces that share a
radio. This fixes a case where external_scan_running was set on a single
interface, but did not block scan on other interfaces.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
In many applications it is useful not just to enumerate a group of well
known access points, but to use a address/mask notation to match an
entire set of addresses (ca:ff:ee:00:00:00/ff:ff:ff:00:00:00).
This change expands the data structures used by MAC lists to include a
mask indicating the significant (non-masked) portions of an address and
extends the list parser to recognize mask suffixes.
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
This change adds the configuration options "bssid_whitelist" and
"bssid_blacklist" used to limit the AP selection of a network to a
specified (finite) set or discard certain APs.
This can be useful for environments where multiple networks operate
using the same SSID and roaming between those is not desired. It is also
useful to ignore a faulty or otherwise unwanted AP.
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
It was possible for the interface not to be marked in INTERFACE_DISABLED
state in case the event was processed for P2P GO because the wpa_s
instance could have been removed in case of a separate group interface.
Change the state first to avoid leaving different state for the case
where separate group interface is not used.
Mark scan to be a normal scan on INTERFACE_ENABLED so that scanning
rules (e.g., skip scan if no networks enabled) get used consistently.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is a race condition between receiving an AP stopped event and
netdev down event. These resulted in different group removal reasons on
a GO device (UNAVAILABLE for stop AP event coming first and REQUESTED
for netdev event first). Make this more consistent by reporting
UNAVAILABLE for both possible cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
The specification requires the tspecs to be kept upon reassociation to
the same BSS. Save the last tspecs before such reassociation, and
reconfigure on the association notification.
Note that the current flow is not transparent to the user
(it is notified about deauth/reassoc and tspec removal/addition).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
In case of roaming, we don't get disassoc notification, but
still want to remove the existing tspecs.
Move the wmm_ac_notify_disassoc() call to the state change
function, which get called also on roaming.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
There is no need to keep temporary keys in memory beyond the end of the
association, so explicitly clear any SAE buffers that can contain keys
as soon as such keys are not needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for auth/assoc timeout/failure event from the driver to
result in unexpected processing during mesh group setup if that
operation was started before the previously started driver operation to
association/connect had completed. Since those events cannot happen in
mesh cases, ignore them to avoid issues due to this corner case.
For example, monitor_iface_unknown_sta followed by wpas_mesh_secure test
case resulted in failure without this change.
Signed-off-by: Jouni Malinen <j@w1.fi>
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add the ability to send a Neighbor Report Request (part of
RRM). Requester is then notified once the report arrives.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
If the last scans are recent (for now, less than ten seconds old), use
them instead of triggering a new scan when a BSS Transition Management
Request frame is received. As a fallback, allow a new scan to be
triggered if no matches were found.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add the TSPEC to the driver on successful TSPEC ADDTS response. Delete
the TSPEC when receiving DELTS action.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Initialize WMM AC data structures upon successful association
with an AP that publishes WMM support, and deinitialize the data
structure when the association is no longer valid.
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Modify network mode to support mode number 5 when CONFIG_MESH is
enabled.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
The mesh peering manager establishes and maintains links among
mesh peers, tracking each peer link via a finite state machine.
This implementation supports open mesh peerings.
[assorted fixes from Yu Niiro <yu.niiro@gmail.com>]
[more fixes from Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-hostap: Bob Copeland <me@bobcopeland.com>
Add routines to (de)initialize mesh interface data structures and
join and leave mesh networks.
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
This commit introduces a QCA vendor command and event to provide an
option to use extended versions of the nl80211 connect/roam operations
in a way that allows drivers to offload key management operations to the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If "STA_AUTOCONNECT 0" has been used to disable automatic connection on
disconnection event and the driver indicates multiple disconnection
events for the disconnection from the current AP when WPS is started, it
could have been possible to hit a case where wpa_s->disconnected was set
to 1 during WPS processing and the following scan result processing
would stop the operation.
wpa_s->key_mgmt == WPA_KEY_MGMT_WPS check was trying to avoid to skip
autoconnect when WPS was in use, but that does not seem to work anymore.
Fix this by checking through wpas_wps_searching() as well to avoid
setting wpa_s->disconnect = 1 when there is an ongoing WPS operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The commit 5cd4740580 has rearranged the
update scan results code and hence the IEs were not getting updated
properly for ap_scan=1 case. This can result in a 4-way handshake
failure in the roaming case (IE mismatch in 3/4 EAPOL). Fix this by
updating the scan results even if ap_scan=1 is used and network does not
need to get reselected based on association information.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Jouni Malinen <j@w1.fi>
Incorrect field was used to determine the init=<value> in the regulatory
domain changed control interface event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is no need to trigger new SA Query procedure to check the state of
the connection immediately after having performed such a check. Limit
the impact of burst of unprotected Deauth/Disassoc frames by starting a
new SA Query procedure only once at least 10 seconds has passed from the
previous SA Query that was triggered by reception of an unprotected
disconnection. The first SA Query procedure for each association does
not follow this rule to avoid issues with test cases that expect to see
an SA Query every time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a link is unreachable, the specification mandates we should send a
teardown packet via the AP with a specific teardown reason. Force this
by first disabling the link and only then sending the teardown packet
for the LOW_ACK event.
Rename the TDLS LOW_ACK event handler to better reflect its purpose.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
This removes number of unnecessary #ifdef CONFIG_P2P blocks from generic
code by hiding the conditional build into p2p_supplicant.h with empty
inline functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids an incorrect ARRAY_VS_SINGLETON report for a case where a
pointer is taken to the specified field in a frame and not to a single
octet. Bounds checking was already handled separately.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_supplicant_event() is required to include the event data for AP mode
events. In theory, a non-AP mode event could be sent here from the
driver wrapper, so reject such event.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is mainly to keep static analyzers silent since it does not look
like this code path can be reached in practice due to the way
association events are handled and current_ssid is either set before
resched here or the association is rejected. Anyway, if this could be
reached, the wpa_supplicant_set_wpa_none_key() call would end up
dereferencing a NULL pointer, so add an explicit check to make sure that
does not happen.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds [DMG] and [PBSS] flags for scan results and BSS table entries
using the IEEE Std 802.11ad-2012 updated definition of the Capability
field.
Signed-off-by: Boris Sorochkin <qca_bsoroc@qca.qualcomm.com>
The radio works for the interface get removed if interface is disabled.
This could have left P2P module in invalid state if the interface got
disabled during a p2p_find or p2p_listen operation. Clear the state in
such a case to avoid blocking following operations due to P2P module
assuming it is still in progress of doing something.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
No need to call ibss_rsn_deinit() again since it is already being called
by wpa_supplicant_mark_disassoc().
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
It is possible for the disconnection event from the driver to not get
delivered when interface is disabled. To maintain consistent ctrl_iface
event behavior, indicate CTRL-EVENT-DISCONNECTED in such a case if we
were in connected state.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows external programs to monitor driver signal change events
through wpa_supplicant when bgscan is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
When an ANQP fetch is triggered and ANQP_3GPP_CELLULAR_NETWORK info is
required, initialize scard to be ready when comparing ANQP and
credentials.
Signed-off-by: Jean Trivelly <jean.trivelly@intel.com>
If a separate P2P group interface is used, PBC overlap during group
formation causes the group interface to be removed, which ends up with
the interface context becoming invalid. Fix this by scheduling a timeout
to process the PBC overlap and interface removal instead of removing the
interface directly before the connection operation has returned.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Scan for GO on the negotiated operating channel for few iterations
before searching on all the supported channels during persistent group
reinvocation. In addition, use the already known SSID of the group in
the scans. These optimizations reduce group formation time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When a sched_scan_stopped event is received and there is a pending PNO,
it used regular scheduled scan parameters instead of PNO specific
parameters. Change it by calling wpas_start_pno().
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This enables more convenient protocol testing of AP and P2P
functionality in various error cases and unexpected sequences without
having to implement each test scenario within wpa_supplicant.
ext_mgmt_frame_handle parameter can be set to 1 to move all management
frame processing into an external program through control interface
events (MGMT-RX and MGMT-TX-STATUS) and command (MGMT_TX). This is
similar to the test interface that was added to hostapd previously, but
allows more control on offchannel operations and more direct integration
with the internal P2P module.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 3d910ef497 tried to make
last-network selection behave more consistently with Interworking
network selection preferences. However, it did not take into account
that other network block may have higher priority. In such cases, the
last added network from Interworking network selection should actually
not be selected for the next connection. Fix this by limiting the
last-network preference to work only within a priority class.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
