Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reorder terms in a way that no invalid pointers are generated with
pos+len operations. end-pos is always defined (with a valid pos pointer)
while pos+len could end up pointing beyond the end pointer which would
be undefined behavior.
Signed-off-by: Jouni Malinen <j@w1.fi>
hmac_sha256() and hmac_sha256_vector() return a result code now, so use
that return value to terminate HMAC-SHA256-based GKDF/MIC similarly to
what was already done with the CMAC-based GKDF/MIC.
Signed-off-by: Jouni Malinen <j@w1.fi>
The recently added ProxyARP support (proxy_arp=1) in hostapd allows a
STA IPv4 address to be learned from DHCP or ARP messages. If that
information is available, add it to Account-Request messages in
Framed-IP-Address attribute.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter no_probe_resp_if_max_sta=1 can
be used to request hostapd not to reply to broadcast Probe Request
frames from unassociated STA if there is no room for additional stations
(max_num_sta). This can be used to discourage a STA from trying to
associate with this AP if the association would be rejected due to
maximum STA limit.
Signed-off-by: Jouni Malinen <j@w1.fi>
If hostapd or wpa_supplicant is built from a git repository, add a
VERSION_STR postfix from the current git branch state. This is from "git
describe --dirty=+". VERSION_STR will thus look something like
"2.6-devel-hostap_2_5-132-g4363c0d+" for development builds from a
modified repository.
This behavior is enabled automatically if a build within git repository
is detected (based on ../.git existing). This can be disabled with
CONFIG_NO_GITVER=y in wpa_supplicant/.config and hostapd/.config.
Signed-off-by: Jouni Malinen <j@w1.fi>
Vendor specific IEs added to frame type P2P_ASSOC_RESP are saved in
the interface context, but as they are added as part of the P2P IEs,
they need to be saved in the global P2P context.
Fix this by directing vendor specific IEs added to P2P_ASSOC_RESP
frame type to the P2P context.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
SAVE_CONFIG command on the global control interface tries to save
the config file on all interfaces. The test disabled updating the
config file only on one interface, thus for configurations that
support a dedicated P2P Device interface, saving the config file
would still have succeeded on the P2P Device interface.
Fix the test by disabling updating the configuration file on the global
control interface (which will, in practice, disable this for the P2P
Device interface) in addition to disabling it on the main interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
mac80211_hwsim only supports 2 different MAC addresses.
Configurations that use a dedicated P2P Device interface already
use these 2 addresses, so adding another interface on the same
PHY results in a duplicated MAC address.
Fix this by changing the MAC address of the added interface to make
sure the new interface has a unique MAC address.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Set the bridge ageing to 1 sec to make the bridge clear unused
addresses after this interval. Otherwise the test depends on
the local configuration of brctl.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Write the main interface address to the tkip_mic_test debugfs file
to generate Michael MIC failure event (which is different than the
p2p_dev_addr when a dedicated P2P Device interface is used).
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
On TPK lifetime expiration, tear down the direct link before renewing
the link in the case of TDLS initiator processing. The expired key
cannot be used anymore, so it is better to explicitly tear down the old
link first.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These test cases verify behavior with parallel scan operations while
going through GO Negotiation and duplicated GO Negotiation Request frame
RX with not-yet-ready sequence in GO Negotiation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This improves robustness of GO Negotiation in special cases where GO
Negotiation Request frames from the peer may end up getting delivered
multiple times, e.g., due to interference and retransmitted frames not
getting properly filtered out in duplicate detection (which is something
that number of drivers do not implement for pre-associated state).
If we have already replied with GO Negotiation Response frame with
Status 1 (not yet ready), do not reply to another GO Negotiation Request
frame from the peer if we have already received authorization from the
user (P2P_CONNECT command) for group formation and have sent out our GO
Negotiation Request frame. This avoids a possible sequence where two
independent GO Negotiation instances could go through in parallel if the
MAC address based rule on avoiding duplicate negotiations is not able to
prevent the case. This can allow GO Negotiation to complete successfully
whereas the previous behavior would have likely resulted in a failure
with neither device sending a GO Negotiation Confirm frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to analyze debug logs for issues related to
multiple pending Action TX frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some drivers (like mac80211) do not accept changing the TX bitrate mask
before the network interface is up. Thus, calling
nl80211_disable_11b_rates() before the interface is up fails, and the
P2P network interface continues to use invalid bitrates.
To fix this call nl80211_disable_11b_rates() immediately after the
interface is brought up (and also after rfkill is unblocked).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Do not expire scan results entries based on scan results from a scan
that was aborted. The aborted scan did not scan all the requested
channels or SSIDs, so the fact that a BSS is missing from the scan
results does not mean it is not available.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
CTWindow was set for all AP interfaces if the driver supports it and
this parameter is set in wpa_supplicant configuration. This results in
failing to start an AP that is not a P2P GO as this setting is rejected
by the driver.
Fix that by setting the CTWindow only for P2P GO interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
While testing, I noticed that printf_encode() makes control characters
human-readable, with one exemption, the DEL character (ASCII 127).
Assuming this exemption was unintentional, make it appear as an escaped
\x7f instead of a literal DEL character in the output.
Signed-off-by: Josh Lehan <krellan@krellan.net>
send_iface_detach_request() can fail and that resulted in skipping a
call to restore_reg_domain() and leaving unexpected country
configuration for following test cases. This could result in failures,
e.g., in this sequence: fst_proto wpas_mesh_open_5ghz
Fix this by ignoring exceptions from send_iface_detach_request() and
continuing to restore regulatory domain.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
atheros_set_opt_ie() needs to be called before freeing drv->wpa_ie to
avoid hitting double-free on the deinit path. Similarly,
drv->wps_beacon_ie and drv->wps_probe_resp_ie could have been used after
being freed. Fix these be moving the atheros_set_opt_ie() call in
atheros_deinit().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for a driver to support sufficient number of channels to
hit the previous limit of 200 characters for the "nl80211: Scan included
frequencies:" debug message. Increase the maximum buffer length to 300
characters to allow more complete list of scanned frequencies to be
written into the debug log. This limit is more in line with the
MAX_REPORT_FREQS (50) limit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In addition to the PTK length increasing, the length of the PMK was
increased (from 256 to 384 bits) for the 00-0f-ac:12 AKM. This part was
missing from the initial implementation and a fixed length (256-bit) PMK
was used for all AKMs.
Fix this by adding more complete support for variable length PMK and use
384 bits from MSK instead of 256 bits when using this AKM. This is not
backwards compatible with the earlier implementations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previous implementation used an obsolete sm->eapol_key_crypt pointer
which was not set anywhere (i.e., was always NULL). In addition, the
condition of sm->eap_if->eapKeyAvailable was not valid here since this
is the case of MSK from an external authentication server and not the
internal EAP server. Consequently, the wpa_auth_pmksa_add() call here
was never used.
The PMKSA cache was still added, but it happened at the completion of
the 4-way handshake rather than at the completion of EAP authentication.
That later location looks better, so delete the unreachable code in
Access-Accept handling. In addition, remove the now complete unused
struct eapol_state_machine eapol_key_* variables.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
With driver wrappers that implement set_privacy(), set_generic_elem(),
set_ieee8021x(), or set_ap_wps_ie(), it was possible to hit a NULL
pointer dereference in error cases where interface setup failed and
the network configuration used WPA/WPA2, IEEE 802.1X, or WPS.
Fix this by skipping the driver operations in case the driver interface
is not initialized.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
I modified this test case for commit
eabf083984 ('tests: P2PS channel
handling') to use dev[2] instead of dev[0], but forgot to update the
p2ps_connect_p2ps_method() dev list to match that. Fix this to actually
use a concurrent connection.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a global D-Bus handler ExpectDisconnect for setting
wpa_s->own_disconnect_req flag. This flag will prevent wpa_supplicant
from adding blacklists and requesting incomplete scan upon the incoming
disconnection. This is mainly meant for a case where suspend/resume is
used and some external component knows about that and can provide the
information to wpa_supplicant before the disconnection happens.
Signed-off-by: Ningyuan Wang <nywang@google.com>
