If you don't choose OpenSSL as TLS implementation and choose to enable
CONFIG_EAP_TNC you have to link against libdl. The OpenSSL libraries
implicitly link against them, so this might be a reason why it wasn't
noticed yet. I assume the same applies to hostapd.
The madwifi driver has interface to set probe request ie.
Attached patch will enable the functionality.
I could see probe request includes WSC IE with this patch.
We can now handle up to 65535 byte result buffer which is the maximum
due to WEXT using 16-bit length field. Previously, this was limited to
32768 bytes in practice even through we tried with 65536 and 131072
buffers which we just truncated into 0 in the 16-bit variable.
This more or less doubles the number of BSSes we can received from scan
results.
I am terribly sorry, but because of a lack of testing equipment the
patch was submitted not properly tested.
Because the chipset documentation is not publicly available all
behaviour has to be found out by experimentation. The other day, I
made some incorrect assumptions based on my findings.
I do believe the attached patch does support the whole RoboSwitch line
(5325, 5350, 5352, 5365 and others). It is a drop-in substitution for
my previous submission.
If wpa_supplicant is started with -u but the DBus service is already
registered wpa_supplicant will bail out. However, it will segfault
in wpa_supplicant_deinit because global->drv_priv wasn't allocated
yet.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
This is based on a patch from Pavel Roskin <proski@gnu.org>, but with
the WIRELESS_DEV part removed instead of moved since it does not apply
anymore. Additional note on client MLME limitations was also added.
MadWifi is unlikely to be in ../head relative to hostapd or
wpa_supplicant, as it would be inside the hostap git repository.
MadWifi sources are more likely to be in a directory called "madwifi"
and residing outside the hostap repository. Using "madwifi" also
demonstrates that the top-level madwifi directory is needed.
Try to match PRI/SEC channel with neighboring 20/40 MHz BSSes per
IEEE 802.11n/D7.0 11.14.3.2. This is not yet complete implementation,
but at least some parts of the 40 MHz coex are improved.
40 MHz operation maybe rejected (i.e., fall back to using 20 MHz) or
pri/sec channels may be switched if needed.
The RoboSwitch driver of wpa_supplicant had one shortcoming: not
supporting the 5365 series. I believe the patch attached fixes this
problem.
Furthermore it contains a small readability rewrite. It basically is an
explicit loop-rollout so that the wpa_driver_roboswitch_leave style
matches that of wpa_driver_roboswitch_join.
If the bind() on /tmp/wpa_ctrl_<pid>_<in-proc-counter> fails with
EADDRINUSE, there is an existing socket file with the name we are trying
to create. Since getpid() is unique, there cannot be another process
using that socket and we can just unlink the file and try again. This
can speed up client connection if wpa_cli is killed without allowing it
to clean up the socket file. [Bug 288]
I think that the "radius" pointer in the structure hostapd_config is
never used; when the configuration is parsed the related data is stored
in hostapd_bss_config's "radius" var.
This adds mostly feature complete external Registrar support with the
main missing part being proper support for multiple external Registrars
working at the same time and processing of concurrent registrations when
using an external Registrar.
This code is based on Sony/Saice implementation
(https://www.saice-wpsnfc.bz/) and the changes made by Ted Merrill
(Atheros) to make it more suitable for hostapd design and embedded
systems. Some of the UPnP code is based on Intel's libupnp. Copyrights
and licensing are explained in src/wps/wps_upnp.c in more detail.
We must not replace M1 with M2D as the last_msg since we need M1 to
validate a possible M2 after M2D. Since M2D and ACK/NACK replies do not
include Authenticator attribute, we can just ignore M2D as far as
updating last_msg is concerned.
The inactivity poll was originally supposed to use Data::Nullfunc, but
due to Prism2/2.5/3 firmware issues, this was changed to an empty
Data::Data frame. mac80211 does not have such an issue, so change the
inactivity poll frame to be Data::Nullfunc by default and use the
Data::Data workaround only with Host AP driver.
Previous version was discarding TX status for FromDS data frames, but
those are the exact ones that we need to check for inactivity poll to
work, i.e., they are TX status reports for injected data frames.
In addition, remove the debug printing of TX status for data frame since
that could fill up the debug output if kernel-side filtering cannot be
used with monitor interface.
TX status information for all transmitted data frames is not going to
be sent to hostapd anymore, so the CPU load with high traffic load is
going to be significantly reduced.
External Registrar in Vista may include NULL termination in the Network
Key when encoding an ASCII passphrase for WPA/WPA2-PSK. As a workaround,
remove this extra octet if present.
If a Registrar tries to configure the AP, but fails to validate the
device password (AP PIN), lock the AP setup after four failures. This
protects the AP PIN against brute force guessing attacks.
This optional configuration parameter can be used to override AP
Settings attributes in M7 similarly to extra_cred option for Credential
attribute(s) in M8.
Buffalo WHR-G125 Ver.1.47 seems to send EAP-WPS packets with too short
EAPOL header length field (14 octets regardless of EAP frame length).
This is fixed in firmware Ver.1.49, but the broken version is included
in many deployed APs. As a workaround, fix the EAPOL header based on the
correct length in the EAP packet. This workaround can be disabled with
eap_workaround=0 option in the network configuration.
Some WPS APs do not set Selected Registrar attribute to 1 properly when
using an external Registrar. Allow such an AP to be selected for PIN
registration after couple of scan runs that do not find APs marked with
Selected Registrar = 1. This allows wpa_supplicant to iterate through
all APs that advertise WPS support without delaying connection with
implementations that set Selected Registrar = 1 properly.
WPS spec is not very specific on the presentation used for the DH
values. The Public Key attribute is described to be 192 octets long, so
that could be interpreted to imply that other places use fixed length
presentation for the DH keys. Change the DH derivation to use fixed
length bufferd by zero padding them from beginning if needed. This can
resolve infrequent (about 1/256 chance for both Public Key and Shared
Key being shorter) interop issues.
This is needed to allow external Registrar (at least the implementation
in Windows Vista) to configure the Enrollee.
With this patch and my previous patch (for wps.c) , I could pass "Wi-Fi
WPS Test Plan Version 1.0 [5.1.4. Add to AP using PIN Config method and
PASS PHRASE through wired external registrar]".
I can't pass the "Wi-Fi WPS Test Plan Version 1.0 [5.1.4. Add to AP
using PIN Config method and PASS PHRASE through wired external
registrar]". The wpa_supplicant-0.6.7 can't recoginize the testbed
AP(BCM94704AGRRev-E.2.4) as WPS PIN AP. Because after PIN entered, the
AP sends Selected Registrar attribute=0 and not send Device Password ID
attribute.
The proposed change as-is removed validation of Selected Registrar
attribute completely. However, that part is not included in this commit
since it can cause problems for environments with multiple WPS-enabled
APs. Another workaround for this will be considered in wpa_supplicant
scanning process (e.g., start trying to use WPS with APs that do not set
Selected Registrar to TRUE after couple of scan runs that do not find
any APs with Selected Registrar TRUE).
Do not initialize EAPOL state machine for the STA when hostapd is
configured to use WPS with open or shared WEP networks. This allows the
STA to use EAPOL-Start to indicate it wants to start WPS in such a case
and hostapd does not end up running through EAPOL authentication timeout
and disconnecting the STA if WPS is not used.
There was already code for starting EAPOL state machines based on
received EAPOL packets, but that was not working properly since
portEnabled was not set to TRUE on that code path. This is now fixed,
too.
This operation can now be moved into an external program by configuring
hostapd with wps_cred_processing=1 and skip_cred_build=1. A new
ctrl_iface message (WPS-REG-SUCCESS <Enrollee MAC addr> <UUID-E>) will
be used to notify external programs of each successful registration and
that can be used as a tricker to move from unconfigured to configured
state.
This behaves like the one in wpa_supplicant, i.e., hostapd can be
configured not to process new credentials (AP settings) internally and
instead pass the WPS attributes for an external program to process over
ctrl_iface.
The default interval is now 5 seconds (used to be 1 second for
interactive mode and 2 seconds for wpa_cli -a). The interval can be
changed with -G<seconds> command line option.
The separate Association Comeback Time IE was removed from IEEE 802.11w
and the Timeout Interval IE (from IEEE 802.11r) is used instead. The
editing on this is still somewhat incomplete in IEEE 802.11w/D7.0, but
still, the use of Timeout Interval IE is the expected mechanism.
The wps_cred_process option can be used to configure wpa_supplicant to
send received Credential attributes for external processing over
ctrl_iface and dbus. This allows external programs to update their
configuration when WPS is used to provision new networks.
This makes it easier to pass the credential data to external programs
(e.g., Network Manager) for processing. The actual use of this data is
not yet included in hostapd/wpa_supplicant.
The current implementation does not support WPA/WPA2-Enterprise
credentials. Ignore any credential that is using unsupported
authentication type to avoid potential issues with partially configured
network blocks.
