This makes it more convenient to run tests with builds that disable
TKIP/WPA(v1) support completely.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is in preparation for a hostapd implementation change on how to
address the unexpected RSNXE Used field value in FTE during FT
reassociation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify hostapd behavior during FT protocol processing when a STA entry
is still present in the AP and that association has PMF negotiated.
Signed-off-by: Jouni Malinen <j@w1.fi>
Include support for MACsec testing in the (vm) kernel by default.
Don't include support in the example hostapd or wpa_supplicant configs
yet since that would potentially break the build on older distributions
like Ubuntu 16.04, which is supported until April 2021.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Specify the secondary channel offset and correct center_freq1 value to
make the parameters complete for a 40 MHz channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
Include a defconfig for building kernel as UML. Also update the README
with a few notes related to UML.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Make the included kernel-config a little more minimal by checking in the
defconfig instead.
Generate the defconfig by checking out a linux at tag wt-2020-03-17,
copy kernel-config to .config, run
'yes "" | make oldconfig && make savedefconfig',
and copy resulting defconfig to kernel-config.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
If we use user-mode-linux, we have time-travel, and then the --long
argument doesn't really make a difference, so just assume that's the
case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
bgscan_learn_beacon_loss was failing quite frequently and it looks like
the background scans were related to those failures. Since those scans
are not really relevant to testing beacon loss, get rid of them in these
test cases to avoid incorrect failures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previously used normal data TX depends on undefined driver behavior
after all keys have been removed. That may not be available, so do this
more properly with frame injection through a monitor interface.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Stopping the AP from beaconing will also stop it from acknowledging
frames and that resulted in bgscan_learn_beacon_loss failing when
mac80211_hwsim is registering REPORTS_TX_ACK_STATUS. Work around this by
moving to using PMF so that the station ignores the unprotected
deauthentiation frames from the AP and also disabling SA Query. This
allows the AP to be stopped and restarted with large enough Beacon
interval to allow the station to detect beacon loss.
This is identical to the earlier design change for
bgscan_simple_beacon_loss (somehow this bgscan_learn_beacon_loss test
case managed to pass at that time).
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks ike the authentication timeouts may continue a bit longer after
some kernel changes and that could result in temporarily disabling the
network profile. Give this test case more time to complete the
connection to avoid reporting failures unnecessarily.
Signed-off-by: Jouni Malinen <j@w1.fi>
Stopping the AP from beaconing will also stop it from acknowledging
frames and that resulted in bgscan_simple_beacon_loss failing when
mac80211_hwsim is registering REPORTS_TX_ACK_STATUS. Work around this by
moving to using PMF so that the station ignores the unprotected
deauthentiation frames from the AP and also disabling SA Query. This
allows the AP to be stopped and restarted with large enough Beacon
interval to allow the station to detect beacon loss.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like this test case can fail if the STA goes to power save mode
and the Deauthentication frame from the AP after session timeout is not
actually sent at all. Check more details to make it clear that this is
indeed the reason behind the failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set device_name in the test cases instead of relying on the
wpa_supplicant configuration file. This fixes problems when we run WPS
test cases in remote test environment.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Leaving out the special sae_pwe value was causing failures for following
test cases, e.g., in the following sequence:
sigma_dut_sae_pw_id_pwe_loop sae_password_id_only
Signed-off-by: Jouni Malinen <j@w1.fi>
Some test case sequences seemed to prevent the station from completing
the first OBSS scan (that scan was aborted) and that resulted in failing
the test case because the AP had not received any report in time. Wait
for scan completion and allow additional scans before timing out to
avoid indicating incorrect AP behavior in cases where the report was not
even received.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Update grpform_pbc_overlap not to require PBC session overlap to be
detected since in this sequence a single BSSID is specified and other
APs can be ignored while checking for session overlap. Add other test
cases to explicitly check for the PBC session overlap detection in
non-P2P and P2P cases when the BSSID is specified.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Replace the hardcoded /tmp filenames for generated ACL and BSS
configuration files with proper temporary files from tempfile.mkstemp()
to avoid conflicts with existing files or with parallel uses. Remove ACL
files from the local directory at the end of each test case. BSS files
are currently left behind, but can be cleaned up separately if needed
for non-VM testing (VM testing has those on ramdrive so they get dropped
automatically at the end) and for remote devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
When this test case is ran in remote test environment, there could be
additional APs in scan results after bssid_filter has been disabled.
That breaks the check on SCAN_RESULTS output. Extend this to cover the
remote testing case by using bssid_filter with both known APs listed
instead of full wildcard.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Instead of hardcoded bss-[1-6]*.conf files, generate them using the
correct BSSID for each AP device and send/install them on the remote
client as well if needed.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Generate ACL files instead of using files with hardcoded values for the
STA MAC addresses. Send the generated files also to the remote client if
required.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Some hostapd test cases use configuration files, e.g., ACLs in BSS
configuration. When executing remote tests (udp), we have to first send
these configuration files to the appropriate remote device. The new
send_file() helper can be used for that.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Hardcoded CONFIG_IEEE80211N to be included to clean up implementation.
More or less all new devices support IEEE 802.11n (HT) and there is not
much need for being able to remove that functionality from the build.
Included this unconditionally to get rid of one more build options and
to keep things simpler.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_open_sta_ps checks whether a STA told its hardware to enter power
save after enabling power save.
ap_open_ps_mc_buf checks whether an AP properly buffers and releases
multicast frames when a STA with PS active is associated.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
A test may want to check multicast connectivity independent of unicast
or check multicast without exercising unicast first. Factor out the
multicast connectivity check code into its own function.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Explicitly flush cfg80211 scan cache for this test case since the BSS
entry check might fail if there are multiple results for the same BSSID.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new dpp_alloc_auth() function addition changed function call
backtraces for memory allocation failure tests.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new dpp_gen_uri() helper function can be used to build the
bootstrapping URI from locally stored information. This can be used to
make it easier to update the URI, e.g., for NFC negotiated connection
handover cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"finally" handler should not trigger a new exception when trying to
clear state for non-DPP builds. In addition, couple of checks for DPP
capability in the build were missing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a helper function for this and add checks for number of test cases
that were missing this. This gets rid of undesired FAIL results
(converts them to SKIP) for test runs where the station do not support
SAE.
Signed-off-by: Jouni Malinen <j@w1.fi>
Explicitly clear cfg80211 scan cache to avoid issues with old BSS
entries from previous test cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previously used timeout of two seconds did not allow more than a
single scan attempt and that could fail every now and then. Make these
more robust by increasing the timeout to 10 seconds which allows another
scan attempt to be completed similarly to the most non-sigma_dut test
cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE P802.11-REVmd was modified to require H2E to be used whenever
Password Identifier is used with SAE. Since wpa_supplicant and mac80211
do not yet support SAE H2E in mesh, Password Identifier cannot be used
in mesh cases. Remove the test cases that verified this behavior for now
to allow H2E to be required per updated REVmd definition. These test
cases will be restored once H2E is fully functionality in mesh cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow running without curses, in which case the log is simply written to
stdout instead of a file. This is useful for automated (but parallel)
testing. Note that in most cases, you'd want to specify --debug, and so
I added a .rstrip() there on the lines to clean that up a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some of the sigma_dut test cases were not yet using try/finally to
ensure stop_sigma_dut() gets called. That could result in not logging
all failure reasons in the log and getting stuck with being unable to
start new sigma_dut processes after failed test cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
There is no point in having to enable this separately for each test case
since the debug details are always useful if something fails.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes logs easier to understand and this may also help in running
over buffer space and getting stuck with sigma_dut termination.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Current Python versions have no os.sleep(), use time.sleep() instead.
module 'os' has no attribute 'sleep'
Traceback (most recent call last):
File "./run-tests.py", line 521, in main
t(dev, apdev)
File "/home/mtheil/hostap/tests/hwsim/test_pmksa_cache.py", line 356, in test_pmksa_cache_expiration
hapd.wait_ptkinitdone(dev[0].own_addr())
File "/home/mtheil/hostap/tests/hwsim/hostapd.py", line 282, in wait_ptkinitdone
os.sleep(0.1)
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
The digestmod argument also exists in earlier Python versions,
version 3.8 does not set a default argument anymore.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
This tests an error, where the p2p_long_listen information from the
wrong device was used internally in wpa_supplicant when using the
separate P2P Device interface.
Signed-off-by: Benjamin Berg <bberg@redhat.com>
This functionality has been available in mac80211_hwsim for years, so
there is no need to maintain this old workaround.
Signed-off-by: Jouni Malinen <j@w1.fi>
