The "FT: Ignore extra data in end" hexdump is quite confusing since it
shows all the IEs that were actually either processed or forwarded.
There is no code path that could reach this debug print with actual real
extra data. Remove it and the dead increment of pos to avoid warnings
from static analyzers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow STA entry to be removed and re-added to the driver with PMF is
used with FT. Previously, this case resulted in cfg80211 rejecting STA
entry update after successful FT protocol use if the association had not
been dropped and it could not be dropped for the PMF case in
handle_auth().
Signed-off-by: Jouni Malinen <j@w1.fi>
Mark own bootstrap information as having been used in NFC negotiated
connection handover and do not accept non-mutual authentication when
processing Authentication Response from the peer when such bootstrapping
information is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Connector alone is not sufficient for authentication during
reconfiguration, so store the netAccessKey as well.
Fixes: e4eb009d98 ("DPP2: Add Connector and C-sign-key in psk/sae credentials for reconfig")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
While the Diffie-Hellman Parameter element is defined in RFC 8110
explicitly for use witht he OWE AKM, it has now been proposed to be used
with another AKM (DPP). Should any other AKM be extended in similar
manner in the future, the check against unexpected use could result in
additional interoperability issues. Remove that and instead, ignore the
unexpected Diffie-Hellman Parameter element if it is included in
(Re)Association Request frame when any other AKM is negotiated.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the Enrollee indicates support for DPP R2 or newer, add Connector and
C-sign-key in psk/sae credentials (i.e., cases where DPP AKM is not
enabled) for reconfiguration. Extend processing of such credentials in
wpa_supplicant network profile addition to handle this new case
correctly by not setting key_mgmt=DPP based on Connector being present,
but by looking at the actual akm value in the config object.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a driver interface event for Beacon frame protection failures.
Report such events over the control interface and send a
WNM-Notification Request frame to the AP as well.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add HE override support under the build parameter CONFIG_HE_OVERRIDES=y.
The disable_he=1 network profile parameter can be used to disable HE.
This requires a fallback to VHT on the 5 GHz band and to HT on the 2.4
GHz band.
There is no nl80211 support for configuring the driver to disable HE, so
for now, this applies only to IBSS and mesh cases.
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
In repeater mode remote AP may request channel switch to a new channel.
Check if DFS is required for the new channel before proceeding with
normal AP operations. Start CAC procedure if radar detection is required
and channel is not yet marked as available.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Add a new hostapd_is_dfs_overlap() helper function to DFS module. This
function tells whether the selected frequency range overlaps with DFS
channels in the current hostapd configuration. Selected frequency reange
is specified by its center frequency and bandwidth.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Rename DFS helper hostapd_config_dfs_chan_available() to
hostapd_is_dfs_chan_available(). Enable access to this helper function
from other hostapd components.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
EVP_PKEY_get0_EC_KEY() was added in OpenSSL 1.1.0, so add a
compatibility wrapper for it when building with OpenSSL 1.0.2.
Fixes: c025c2eb59 ("DPP: DPPEnvelopedData generation for Configurator backup")
Fixes: 7d9e320054 ("DPP: Received Configurator backup processing")
Signed-off-by: Jouni Malinen <j@w1.fi>
The new skip_prune_assoc=1 parameter can be used to configure hostapd
not to prune associations from other BSSs operated by the same process
when a station associates with another BSS. This can be helpful in
testing roaming cases where association and authorization state is
maintained in an AP when the stations returns.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new driver param full_ap_client_state=0 can be used to test
functionality with the driver capability for full AP client state being
forced to be disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use local variables to avoid sm->wpa_auth->conf type of dereferences
where multiple instances within a function can be cleaned up.
Signed-off-by: Jouni Malinen <j@w1.fi>
Drivers that trigger roaming need to know the lifetime and reauth
threshold time of configured PMKSA so that they can trigger full
authentication to avoid unnecessary disconnection. To support this, send
dot11RSNAConfigPMKLifetime and dot11RSNAConfigPMKReauthThreshold values
configured in wpa_supplicant to the driver while configuring a PMKSA.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
The new hostapd configuration parameter dpp_pfs can be used to specify
how PFS is applied to associations. The default behavior (dpp_pfs=0)
remains same as it was previously, i.e., allow the station to decide
whether to use PFS. PFS use can now be required (dpp_pfs=1) or rejected
(dpp_pfs=2).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add definition for HE bit in neighbor report BSSID Information field
from IEEE P802.11ax/D6.0, 9.4.2.36 Neighbor Report element.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
This functionality was repeated for multiple different frames. Use a
shared helper function to avoid such duplication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process the received Presence Announcement frames in Controller. If a
matching bootstrapping entry for the peer is found, initiate DPP
authentication to complete provisioning of the Enrollee.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process the received Presence Announcement frames in AP/Relay. If a
matching bootstrapping entry for the peer is found in a local
Configurator, that Configurator is used. Otherwise, the frame is relayed
to the first configured Controller (if available).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process received Presence Announcement frames and initiate
Authentication exchange if matching information is available on the
Configurator.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new hostapd configuration parameter
dpp_configurator_connectivity=1 to request Configurator connectivity to
be advertised for chirping Enrollees.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wpa_supplicant control interface command "DPP_CHIRP own=<BI
ID> iter=<count>" to request chirping, i.e., sending of Presence
Announcement frames, to be started.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new identifier definitions for presence announcement,
reconfiguration, and certificate enrollment.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"DPP_BOOTSTRAP_SET <ID> <configurator parameters..>" can now be used to
set peer specific configurator parameters which will override any global
parameters from dpp_configurator_params.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a more convenient way of addressing cases where a
Configurator/Controller may store a large number of peer bootstrapping
information instances and may need to manage different configuration
parameters for each peer while operating as the Responder.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Set the global pointer and msg_ctx when allocating struct
dpp_authentication instead of needing to pass these to
dpp_set_configurator().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd (and wpa_supplicant in AP mode) was internally updating the STA
flags on disconnection cases to remove authorization and association.
However, some cases did not result in immediate update of the driver STA
entry. Update all such cases to send out the update to the driver as
well to reduce risk of race conditions where new frames might be
accepted for TX or RX after the port authorization or association has
been lost and configured keys are removed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check whether the Transition Disable KDE is received from an
authenticated AP and if so, whether it contains valid indication for
disabling a transition mode. If that is the case, update the local
network profile by removing the less secure options.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new hostapd configuration parameter transition_disable can now be
used to configure the AP to advertise that use of a transition mode is
disabled. This allows stations to automatically disable transition mode
by disabling less secure network profile parameters.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the OUI Type and bitmap values for Transition Disable KDE. These
will be shared by both the AP and STA implementations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA_WLAN_VENDOR_CFR_NDPA_NDP_ALL in enum
qca_wlan_vendor_cfr_capture_type. This capture type requests all NDPA
NDP frames to be filtered.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd will trigger EDMG auto channel selection by setting
QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED. The 60 GHz driver will be
called to start an auto channel selection and will return the
primary channel and the EDMG channel.
Signed-off-by: Noam Shaked <nshaked@codeaurora.org>
Addition of chan_2ghz_or_5ghz_to_freq() broke 60 GHz ACS, because it
assumes reported ACS channel is on either 2.4 or 5 GHz band. Fix this
by converting chan_2ghz_or_5ghz_to_freq() to a more generic
chan_to_freq(). The new function uses hw_mode to support 60 GHz.
Fixes: 41cac481a8 ("ACS: Use frequency params in ACS (offload) completed event interface")
Signed-off-by: Noam Shaked <nshaked@codeaurora.org>
The parameters that need to be applied are symmetric to those of VHT,
however the validation code needs to be tweaked to check the HE
capabilities.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Enhanced channel frequency response supports capturing of channel status
information based on RX. Define previous CFR as version 1 and enhanced
CFR as version 2. If target supports both versions, two versions can't
be enabled at same time. Extend attributes for enhanced CFR capture in
enum qca_wlan_vendor_peer_cfr_capture_attr.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Support Extended Key ID in wpa_supplicant according to
IEEE Std 802.11-2016 for infrastructure (AP) associations.
Extended Key ID allows to rekey pairwise keys without the otherwise
unavoidable MPDU losses on a busy link. The standard is fully backward
compatible, allowing STAs to also connect to APs not supporting it.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Support Extended Key ID in hostapd according to IEEE Std 802.11-2016.
Extended Key ID allows to rekey pairwise keys without the otherwise
unavoidable MPDU losses on a busy link. The standard is fully backward
compatible, allowing an AP to serve STAs with and without Extended Key
ID support in the same BSS.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
This is more consistent with the other eloop registrations and avoids a
theoretical integer overflow with 16-bit int should more than 32767
sockets/signals/events be registered.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is more consistent with the other eloop registrations and avoids a
theoretical integer overflow with 16-bit int should more than 32767
sockets be registered (which is not really going to happen in practice).
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids a theoretical integer overflow with 16-bit unsigned int
should a certificate be encoded with more that 65535 friendly names or
icons.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is more consistent with the other eloop registrations and avoids a
theoretical integer overflow with 16-bit int (not that there would ever
be more that 32767 signal handlers getting registered).
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no point in starting a huge number of pending SA Queries, so
limit the number of pending queries to 1000 to have an explicit limit
for how large sa_query_count can grow.
Signed-off-by: Jouni Malinen <j@w1.fi>
While RADIUS messages are limited to 4 kB, use size_t to avoid even a
theoretical overflow issue with 16-bit int.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the kernel rtm_newlink or rtm_dellink send the maximum length of
ifname (IFNAMSIZ), the event handlers in
wpa_driver_nl80211_event_rtm_addlink() and
wpa_driver_nl80211_event_rtm_dellink() did not copy the IFLA_IFNAME
value. Because the RTA_PAYLOAD (IFLA_IFNAME) length already includes the
NULL termination, that equals the IFNAMSIZ.
Fix the condition when IFNAME reach maximum size.
Signed-off-by: Ouden <Ouden.Biz@gmail.com>
Add more hang reason codes for the hang reason in the
QCA_NL80211_VENDOR_SUBCMD_HANG events. This also introduces the
attribute QCA_WLAN_VENDOR_ATTR_HANG_REASON_DATA to carry the required
data for the respective hang reason. This data is expected to contain
the required dump to analyze the reason for the hang.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Some APs have managed to add two SSID elements into Beacon frames and
that used to result in picking the last one which had incorrect data in
the known examples of this misbehavior. Pick the first one to get the
correct SSID.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was not supposed to be conditional on CONFIG_FILS.
Fixes: ecbf59e693 ("wpa_supplicant configuration for Beacon protection")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
int_array_concat() and int_array_add_unique() could potentially end up
overflowing the int type variable used to calculate their length. While
this is mostly theoretical for platforms that use 32-bit int, there
might be cases where a 16-bit int overflow could be hit. This could
result in accessing memory outside buffer bounds and potentially a
double free when realloc() ends up freeing the buffer.
All current uses of int_array_add_unique() and most uses of
int_array_concat() are currently limited by the buffer limits for the
local configuration parameter or frame length and as such, cannot hit
this overflow cases. The only case where a long enough int_array could
be generated is the combination of scan_freq values for a scan. The
memory and CPU resource needs for generating an int_array with 2^31
entries would not be realistic to hit in practice, but a device using
LP32 data model with 16-bit int could hit this case.
It is better to have more robust checks even if this could not be
reached in practice, so handle cases where more than INT_MAX entries
would be added to an int_array as memory allocation failures instead of
allowing the overflow case to proceed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter no_beacon_rsnxe=1 can be used to
remove RSNXE from Beacon frames. This can be used to test protection
mechanisms for downgrade attacks.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous design for adding RSNXE into FT was not backwards
compatible. Move to a new design based on 20/332r3 to avoid that issue
by not include RSNXE in the FT protocol Reassociation Response frame so
that a STA not supporting RSNXE can still validate the FTE MIC
correctly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous design for adding RSNXE into FT was not backwards
compatible. Move to a new design based on 20/332r3 to avoid that issue
by not include RSNXE in the FT protocol Reassociation Request frame so
that an AP not supporting RSNXE can still validate the FTE MIC
correctly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that the AP included RSNXE in Beacon/Probe Response frames if it
indicated in FTE that RSNXE is used. This is needed to protect against
downgrade attacks based on the design proposed in 20/332r3.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that the STA includes RSNXE if it indicated in FTE that RSNXE is
used and the AP is also using RSNXE. This is needed to protect against
downgrade attacks based on the design proposed in 20/332r3.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a workaround needed to keep FT protocol backwards compatible for
the cases where either the AP or the STA uses RSNXE, but the other one
does not. This commit adds setting of the new field to 1 in
Reassociation Request/Response frame during FT protocol when the STA/AP
uses RSNXE in other frames. This mechanism is described in 20/332r3.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add key configuration parameters needed to support Extended Key ID with
pairwise keys. Add a driver capability flag to indicate support forusing
this.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
wpa_parse_kde_ies(), i.e., the only caller to wpa_parse_generic(),
verifies that there is room for KDE Length field and pos[1] (that
length) octets of payload in the Key Data buffer. The PMKID KDE case
within wpa_parse_generic() was doing an unnecessary separate check for
there being room for the Length, OUI, and Data Type fields. This is
covered by the check in the calling function with the combination of
verifying that pos[1] is large enough to contain RSN_SELECTOR_LEN +
PMKID_LEN octets of payload.
This is confusing since no other KDE case was checking remaining full
buffer room within wpa_parse_generic(). Clean this up by removing the
unnecessary check from the PMKID KDE case so that all KDEs are handled
consistently.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_parse_generic() can now recognize the Key ID KDE that will be needed
to deliver the Key ID of the pairwise key when Extended Key ID is used.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
KEY_FLAG_MODIFY was initial added for the planned Extended Key ID
support with commit a919a26035 ("Introduce and add key_flag") and then
removed with commit 82eaa3e688 ("Remove the not yet needed
KEY_FLAG_MODIFY") to simplify commit e9e69221c1 ("Validity checking
function for key_flag API").
Add it again and update check_key_flag() accordingly.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The actual TX status (whether ACK frame was received) was not included
in the debug log in AP mode. Add that for all cases. In addition, add
some more details in the debug log to make the log more helpful in
debugging issues related to frame delivery.
Signed-off-by: Jouni Malinen <j@w1.fi>
While 13.7.1 (FT reassociation in an RSN) in P802.11-REVmd/D3.0 did not
explicitly require this to be done, this is implied when describing the
contents of the fourth message in the FT authentication sequence (see
13.8.5). Furthermore, 20/332r2 is proposing an explicit validation step
to be added into 13.7.1.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 5f9b4afd ("Use frequency in HT/VHT validation steps done before
starting AP") modified hostapd_is_usable_edmg() to use freq instead of
channel numbers. Unfortunately, it did not convert the frequency
calculation correctly and this broke EDMG functionality.
Fix the frequency calculation so that EDMG channel 9 works again.
Fixes: 5f9b4afdfa ("Use frequency in HT/VHT validation steps done before starting AP")
Signed-off-by: Hrishikesh Vidwans <hvidwans@codeaurora.org>
Check whether an error is reported from any of the functions that could
in theory fail and if so, do not proceed with the partially filled SAE
commit buffer.
Signed-off-by: Jouni Malinen <j@w1.fi>
In theory, hmac_sha256() might fail, so check for that possibility
instead of continuing with undetermined index value that could point to
an arbitrary token entry.
Signed-off-by: Jouni Malinen <j@w1.fi>
The return value from nl80211_send_monitor() is not suitable for use
with strerror(). Furthermore, nl80211_send_monitor() itself is printing
out a more detailed error reason.
Signed-off-by: Jouni Malinen <j@w1.fi>
send_and_recv_msgs() returns a negative number as the error code and
that needs to be negated for strerror().
Fixes: 8759e9116a ("nl80211: Control port over nl80211 helpers")
Signed-off-by: Jouni Malinen <j@w1.fi>
send_auth_reply() could be called with sta == NULL in certain error
conditions. While that is not applicable for this special test
functionality for SAE, the inconsistent checks for the sta pointer could
result in warnings from static analyzers. Address this by explicitly
checking the sta pointer here.
Signed-off-by: Jouni Malinen <j@w1.fi>
mode->he_capab is an array and as such, there is no point in checking
whether it is NULL since that cannot be the case. Check for the
he_supported flag instead. In addition, convert the TWT responder
capability bit into a fixed value 1 to avoid any surprising to the
callers. In practice, neither of these changes results in different
behavior in the current implementation, but this is more robust.
Signed-off-by: Jouni Malinen <j@w1.fi>
There was a copy-paste error in this code that would be adding the
connectorTemplate once that becomes available. In practice, this was not
reachable code, but anyway, this should be ready for potential addition
of connectorTemplate in the future.
Signed-off-by: Jouni Malinen <j@w1.fi>
While there may have initially been cases where the RSNE from
Beacon/Probe Response frames was not available from some drivers, it is
now more valuable to notice if such a case were to be hit with drivers
that are always expected to have such information available. As such,
make it a fatal error if the scan results for the current AP are not
available to check the RSNE/RSNXE in EAPOL-Key msg 3/4.
Signed-off-by: Jouni Malinen <j@w1.fi>
Avoid printing confusing FT debug entries from wpa_sm_set_ft_params()
when FT is not actually used for the connection.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use the same reason code to indicate that IE different in 4-way
handshake and also print a hexdump of RSNXE in both Beacon/ProbeResp and
EAPOL-Key msg 3/4 in the log.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter rsne_override_eapol can now be
used similarly to the previously added rsnxe_override_eapol to override
(replace contents or remove) RSNE in EAPOL-Key msg 3/4. This can be used
for station protocol testing to verify sufficient checks for RSNE
modification between the Beacon/Probe Response frames and EAPOL-Key msg
3/4.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previous implementation was determining whether the override value was
set based on its length being larger than zero. Replace this with an
explicit indication of whether the parameter is set to allow zero length
replacement, i.e., remove of RSNXE from EAPOL-Key msg 3/4.
In addition, move IE replacement into a more generic helper function to
allow this to be used with other IEs as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
The 4-address frames WDS design in mac80211 uses VLAN interfaces
similarly to the way VLAN interfaces based on VLAN IDs are used. The EAP
authentication case ended up overriding the WDS specific assignment even
when the RADIUS server did not assign any specific VLAN for the STA.
This broke WDS traffic.
Fix this by skipping VLAN assignment to VLAN ID 0 for STAs that have
been detected to use 4-address frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
The resource-load-started cannot be used to replace the older
resource-request-starting signal and as such, the final redirect to the
special http://localhost:12345/ URL did not work. Use the decide-policy
signal for navigation action instead.
Also remove the attempt to modify the request URI from
resource-load-started since that is not going to work either. This is
not really critical for functionality, but could eventually be replaced
with a handler for the WebKitWebPage send-request signal.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_tdls_set_key() did set the key_id to -1 to avoid a useless
NL80211_CMD_SET_KEY call that the updated nl80211 driver no longer
carries out. Remove the no longer required workaround.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
After a radar signal is detected, the AP should switch to another
channel, but in the case of 80+80 MHz, channel switch failed because
hostapd did not select the secondary channel in the process. Fix this by
selecting a secondary channel in the case of 80+80 MHz.
Signed-off-by: Xin Wang <xwangw@codeaurora.org>
Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
The initial implementation of the PTK derivation workaround for
interoperability with older OWE implementations forced
WPA_KEY_MGMT_PSK_SHA256 to be used for all of PTK derivation. While that
is needed for selecting which hash algorithm to use, this was also
changing the length of the PTK components and by doing so, did not
actually address the backwards compatibility issue.
Fix this by forcing SHA256 as the hash algorithm in PTK derivation
without changing the PTK length calculation for OWE when
owe_ptk_workaround is enabled.
Fixes: 65a44e849a ("OWE: PTK derivation workaround in AP mode")
Fixes: 8b138d2826 ("OWE: PTK derivation workaround in STA mode")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Migrate nl80211 driver to key_flag API and add additional sanity checks.
I'm still not sure why we install unicast WEP keys also as default
unicast keys. Based on how I understand how mac80211 handles that it
should be pointless. I just stuck to how we do things prior to the patch
for WEP keys to not break anything. After all other drivers may need it.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Always report an error when NL80211_CMD_SET_KEY can't set a key to
default.
The old ioctl-based design used a single command to add, set, and delete
a key and had to ignore ENOENT for key deletions. It looks like that
special handling was also ported for NL80211_CMD_NEW_KEY and
NL80211_CMD_SET_KEY instead only for NL80211_CMD_DEL_KEY.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Calling NL80211_CMD_NEW_KEY with NL80211_KEY_DEFAULT_TYPES attributes is
pointless. The information is not expected and therefore the kernel
never forwards it to the drivers. That attribute is used with
NL80211_CMD_SET_KEY.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Allow to abort key installations with different error codes and fix one
misleading return code.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Turns out we are sometime providing a seq when deleting the key. Since
that makes no sense on key deletion let's stop forwarding that to the
driver at least.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Add masks for each key type to define which flags can be combined and
add a helper function to validate key_flag values.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
I decided to drop KEY_FLAG_MODIFY instead of allowing flag combinations not
yet used in the code and will simply recreate it with the Extended Key
ID patches once we get there. For that reason I also did not renumber
the flags.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
hostapd_broadcast_wep_set() can be called without a WEP key set.
Don't try to install a default key in that case.
This patch is not critical for the new API. With key_flag we just would
report an (ignored) error and do nothing. With the patch we simply do
nothing.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The unicast parameter in set_wep_key() is only expected to be set to 0
or 1. Without this patch we set unicast to 0x80 instead of 1. Since
unicast is used as boolean that is working fine but violates the
documented API.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
This clears the AuthorizedMACs advertisement immediately when the
Selected Registrar timeout is hit and no more active PINs are present.
Previously, the AuthorizedMACs advertisement could remain in place
indefinitely since expired PINs were removed only when actually trying
to find a PIN for a new WPS exchange.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it easier to understand what is happening when a new channel
needs to be selected based on a radar detection event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Upon radar detection we used to search channels with the same bandwidth.
This way we might not find any other channels. If there are no channels
available with that bandwidth the AP service will be stopped. To avoid
this problem, also search a suitable channel by downgrading the
bandwidth. This scenario is applicable during CAC as well.
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
In the normal case hostapd_disable_iface() and hostapd_enable_iface()
will be done while switching to another DFS channel upon radar
detection. In certain scenarios radar detected event can come while
hostapd_disable_iface() is in progress and iface->current_mode will be
NULL in that scenario. Previously, we did not check for this scenario
and proceeded with the radar detection logic which can trigger a
segmentation fault. To fix this, avoid proceeding the radar detection
event if iface->current_mode is NULL.
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
The commit a34ca59e (SAE: Allow SAE password to be configured separately
(STA)) added sae_password configuration option. We should also consider
sae_password in the wpa_config_write() function which stores the valid
network block details to an external database.
Fixes: a34ca59e4d ("SAE: Allow SAE password to be configured separately (STA)")
Signed-off-by: Sachin Shelke <sachin.shelke@nxp.com>
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
There is no support for using the control port for sending out EAPOL
frames through privsep yet, so mask out this capability to fall back to
the l2_packet based design.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add support for element defragmentation as defined in IEEE
P802.11-REVmd/D3.0, 10.28.12 (Element defragmentation).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
IEEE P802.11az/D2.0 renamed the FILS Wrapped Data element,
removing the FILS prefix. Change the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
To support PASN authentication flow, where Authentication frames are
sent by wpa_supplicant using the send_mlme() callback, modify the logic
to also send EVENT_TX_STATUS for Authentication frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
PASN authentication can be performed while a station interface is
connected to an AP. To allow sending PASN frames while connected, extend
the send_mlme() driver callback to also allow a wait option. Update the
relevant drivers and wpa_supplicant accordingly.
hostapd calls for send_mlme() are left unchanged, since the wait option
is not required there.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
If the driver requires external SAE authentication, it would result in
registration for all Authentication frames, so even non-SAE
Authentication frames might be forwarded to user space instead of being
handled internally. Fix this by using a more strict match pattern,
limiting the registration to the SAE authentication algorithm only.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
WEP provisioning was removed from WPS v2, so this workaround
functionality has not been applicable. Remove it completely.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was already supported in the offload ACS case and this commit
completes support for this with the internal ACS algorithm.
Signed-off-by: Neo Jou <neojou@gmail.com>
Set iface->current_mode and iface->conf->hw_mode when completing ACS
based on the selected channel in the hw_mode=any case.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
Add suitable channel frequencies from all modes into the scan parameters
when a single mode is not specified for ACS. This is preparation for
being able to support hw_mode=any to select the best channel from any
supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
This is preparation for being able to support hw_mode=any to select the
best channel from any supported mode.
Signed-off-by: Neo Jou <neojou@gmail.com>
While the users of os_random() do not really need strong pseudo random
numebrs, there is no significant harm in seeding random() with data from
os_get_random(), i.e., /dev/urandom, to get different sequence of not so
strong pseudo random values from os_random() for each time the process
is started.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since SAE PMK can be updated only by going through a new SAE
authentication instead of being able to update it during an association
like EAP authentication, do not allow PMKSA entries to be used for
caching after the reauthentication threshold has been reached. This
allows the PMK to be updated without having to force a disassociation
when the PMK expires if the station roams between the reauthentication
threshold and expiration timeout.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Since SAE PMK can be updated only by going through a new SAE
authentication instead of being able to update it during an association
like EAP authentication, do not allow PMKSA entries to be used for OKC
after the reauthentication threshold has been reached. This allows the
PMK to be updated without having to force a disassociation when the PMK
expires if the station roams between the reauthentication threshold and
expiration timeout.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
SAE authentication derives PMKID differently from the EAP cases. The
value comes from information exchanged during SAE authentication and
does not bind in the MAC addresses of the STAs. As such, the same PMKID
is used with different BSSIDs. Fix both the hostapd and wpa_supplicant
to use the previous PMKID as is for OKC instead of deriving a new PMKID
using an incorrect derivation method when using an SAE AKM.
This fixes use of opportunistic key caching with SAE.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wpa_ctrl.h can be installed separately with libwpa_client, so
utils/common.h won't be available to its users.
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Add an attribute QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME for specifying
dwell time in the QCA vendor scan command. This is a common value which
applies across all frequencies requested in the scan.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This attribute enables/disables the host driver to send roam reason
information in the Reassociation Request frame to the AP in the same
ESS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Couple of the attributes were defined with inconsistent prefix in the
name (missing "CONFIG_"). Fix these to use the common prefix for all
enum qca_wlan_vendor_attr_config values. Add defined values for the
incorrect names to avoid issues with existing users.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new capability flag based on the nl80211 feature advertisement and
start using the new default key type for Beacon protection. This enables
AP mode functionality to allow Beacon protection to be enabled. This is
also enabling the previously added ap_pmf_beacon_protection_* hwsim test
cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The cookie values for UDP control interface commands was defined as a
static global array. This did not allow multi-BSS test cases to be
executed with UDP control interface. For example, after
hapd1 = hostapd.add_bss(apdev[0], ifname1, 'bss-1.conf')
hapd2 = hostapd.add_bss(apdev[0], ifname2, 'bss-2.conf')
hapd1->ping() did not work.
Move those cookie values to per-instance location in struct
hapd_interfaces and struct hostapd_data to fix this.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Rekeying a pairwise key using only keyid 0 (PTK0 rekey) has many broken
implementations and should be avoided when using or interacting with
one. The effects can be triggered by either end of the connection and
range from hardly noticeable disconnects over long connection freezes up
to leaking clear text MPDUs.
To allow affected users to mitigate the issues, add a new configuration
option "wpa_deny_ptk0_rekey" to replace all PTK0 rekeys with fast
reconnects.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Rekeying a pairwise key using only keyid 0 (PTK0 rekey) has many broken
implementations and should be avoided when using or interacting with
one. The effects can be triggered by either end of the connection and
range from hardly noticeable disconnects over long connection freezes up
to leaking clear text MPDUs.
To allow affected users to mitigate the issues, add a new hostapd
configuration option "wpa_deny_ptk0_rekey" to replace all PTK0 rekeys
with disconnection. This requires the station to reassociate to get
connected again and as such, can result in connectivity issues as well.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The CAN_REPLACE_PTK0 flag provided by nl80211 can be used to detect if
the card/driver is explicitly indicating capability to rekey STA PTK
keys using only keyid 0 correctly.
Check if the card/driver supports it and make the status available as a
driver flag.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The MBO PMF check for AP SME in the driver case was added into a
location that is skipped for WPS processing. That was not really the
correct place for this since the skip_wpa_check label was supposed to
remain immediately following the WPA checks. While this does not really
have much of a practical impact, move the check around so that the
skip_wpa_check label remains where it is supposed to be.
Fixes: 4c572281ed ("MBO: Mandate use of PMF for WPA2+MBO association (AP)")
Signed-off-by: Jouni Malinen <j@w1.fi>
Save RM enabled capability element of an associating station when
hostapd use the device AP SME similarly to how this information is saved
with SME-on-hostapd cases. This allows radio measurement operations
(e.g., REQ_BEACON) to be used.
Signed-off-by: Ouden <Ouden.Biz@gmail.com>
This element is not used in Beacon or Probe Response frames (which is
the reason why the standard does not indicate where exactly it would be
in those frames..); HT Operation element has this information and so
does Extended CSA element.
In practice, this reverts the functionality added in commit 76aab0305c
("Add secondary channel IE for CSA").
Signed-off-by: Jouni Malinen <j@w1.fi>
Hardcoded CONFIG_IEEE80211N to be included to clean up implementation.
More or less all new devices support IEEE 802.11n (HT) and there is not
much need for being able to remove that functionality from the build.
Included this unconditionally to get rid of one more build options and
to keep things simpler.
Signed-off-by: Jouni Malinen <j@w1.fi>
Split the IEs from WPA authenticator state machine into separately added
IEs so that the exact location between these and other elements can be
controlled. This fixes the location of MDE and RSNXE in Beacon and Probe
Response frames. In addition, this swaps the order of BSS Load and RM
Enabled Capabilities elements in Beacon frames to get them into the
correct order (which was already used for Probe Response frames).
Furthermore, this fixes the buffer end checks for couple of elements to
make the implementation more consistent (though, in practice, there is
no impact from this since the old size limit was smaller than needed,
but still sufficiently large to have room for these).
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new wpa_supplicant network profile configuration parameter
beacon_prot=<0/1> to allow Beacon protection to be enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new hostapd configuration parameter beacon_prot=<0/1> to allow
Beacon protection to be enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
nla_nest_start() might fail, so need to check its return value similarly
to all the other callers.
Fixes: a84bf44388 ("HE: Send the AP's OBSS PD settings to the kernel")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously only couple of AKM suite selectors were converted into
NL80211_ATTR_AKM_SUITES. Add rest of the AKM suites here. However, since
the current kernel interface has a very small limit
(NL80211_MAX_NR_AKM_SUITES = 2), add the attribute only when no more
than that limit entries are included. cfg80211 would reject the command
with any more entries listed.
This needs to be extended in cfg80211/nl80211 in a backwards compatible
manner, so this seems to be the best that can be done for now in user
space. Many drivers do not use this attribute, so must not reject the
configuration completely when larger number of AKM suites is configured.
Such cases may not work properly with drivers that depend on
NL80211_ATTR_AKM_SUITES value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to work around a missing attribute that would cause
cfg80211 to reject some nl80211 commands (e.g.,
NL80211_ATTR_VENDOR_DATA) with new kernel versions that enforce netlink
attribute policy validation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use a single block each for webkit and webkit2 signal handlers. This
cleans up browser.c to have clear sections for each webkit API version.
Signed-off-by: Jouni Malinen <j@w1.fi>
Avoid unnecessary warnings from webkit on calling gtk_main_quit() more
than once for a single gtk_main() call. This is also fixing an issue for
a corner case where the very first URL has special purpose (osu:// or
http://localhost:12345).
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation of hovering-over-link signal handler did not
really work with webkit2, so replace this with mouse-target-changed
handler.
Signed-off-by: Jouni Malinen <j@w1.fi>
hs20_web_browser() was previously hardcoded to not perform strict TLS
server validation. Add an argument to this function to allow that
behavior to be configured. The hs20-osu-client users are still using the
old behavior, i.e., not validating server certificates, to be usable for
testing purposes.
Signed-off-by: Jouni Malinen <j@w1.fi>
SM Power Save was described in somewhat unclear manner in IEEE Std
802.11n-2009 as far the use of it locally in an AP to save power. That
was clarified in IEEE Std 802.11-2016 to allow only a non-AP STA to use
SMPS while the AP is required to support an associated STA doing so. The
AP itself cannot use SMPS locally and the HT Capability advertisement
for this is not appropriate.
Remove the parts of SMPS support that involve the AP using it locally.
In practice, this reverts the following commits:
04ee647d58 ("HT: Let the driver advertise its supported SMPS modes for AP mode")
8f461b50cf ("HT: Pass the smps_mode in AP parameters")
da1080d721 ("nl80211: Advertise and configure SMPS modes")
Signed-off-by: Jouni Malinen <j@w1.fi>
Set the proper bits inside the extended capabilities field to indicate
support for TWT responder.
Tested-by: John Crispin <john@phrozen.org>
Signed-off-by: Mikhail Karpenko <karpenko@fastmail.com>
The HE Operation field for BSS color consists of a disabled, a partial,
and 6 color bits. The original commit adding support for BSS color
considered this to be a u8. This commit changes this to the actual
bits/values.
This adds an explicit config parameter for the partial bit. The disabled
is set to 0 implicitly if a bss_color is defined.
Interoperability testing showed that stations will require a BSS color
to be set even if the feature is disabled. Hence the default color is 1
when none is defined inside the config file.
Signed-off-by: John Crispin <john@phrozen.org>
Commit 2bab073dfe ("WPS: Add new PSK entries with wps=1 tag") added
this when writing the new entry into a file, but the in-memory update
did not get the tag. Add it there as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
Now that hostapd wpa_psk_file has a new tag for identifying PSKs that
can be used with WPS, add that tag to new entries for PSKs from WPS.
This makes it clearer where the PSK came from and in addition, this
allows the same PSK to be assigned if the same Enrollee goes through WPS
provisioning again.
Signed-off-by: Jouni Malinen <j@w1.fi>
By default, when configuration file set wpa_psk_file, hostapd generated
a random PSK for each Enrollee provisioned using WPS and appended that
PSK to wpa_psk_file.
Changes that behavior by adding a new step. WPS will first try to use a
PSK from wpa_psk_file. It will only try PSKs with wps=1 tag.
Additionally it'll try to match enrollee's MAC address (if provided). If
it fails to find an appropriate PSK, it falls back to generating a new
PSK.
Signed-off-by: Tomasz Jankowski <tomasz.jankowski@plume.com>
In the function owe_assoc_req_process(), values assigned to the reason
argument imply that it should be renamed to status. Rename 'reason' to
'status' and modify the uses of owe_assoc_req_process() accordingly.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
This commit adds new attributes for getting the Probe Response frame
IEs, Beacon frame IEs and the disconnection reason codes through
get_sta_info vendor command.
The host driver shall give this driver specific reason code through
the disconnection reason code attribute
QCA_WLAN_VENDOR_ATTR_GET_STA_DRIVER_DISCONNECT_REASON.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This acts as an event from the host driver to the user space to notify
the driver specific reason for a disconnection. The host driver
initiates the disconnection for various scenarios (beacon miss, Tx
Failures, gateway unreachability, etc.) and the reason codes from
cfg80211_disconnected() do not carry these driver specific reason codes.
Host drivers should trigger this event immediately prior to triggering
cfg80211_disconnected() to allow the user space to correlate the driver
specific reason code with the disconnect indication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This acts as a vendor event and is used to update the information
of a station from the driver to userspace.
Add an attribute for the driver to update the channels scanned in
the last connect/roam attempt.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Some of the operating classes added in the 6 GHz band have a larger
number of channels included in them (e.g., operating class 131 has 59
channels). Increase the maximum number of channels per operating class
so that all channels will get populated.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This attribute aims to configure the STA to send the Beacon Report
Response with failure reason for the scenarios where the Beacon Report
Request cannot be handled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This ugly hack for being able to search for optional arguments with
space before them was quite inconvenient and unexpected. Clean this up
by handling this mess internally with a memory allocation and string
duplication if needed so that the users of wpa_supplicant control
interface do not need to care about such details.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
As qca_vendor.h alone can be included by other applications, define
macro BIT() in qca_vendor.h itself if not yet defined, e.g., by
including utils/common.h before qca_vendor.h.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wlantest build did not define build options to determine key management
values for SAE, OWE, and DPP. Add those and the needed SHA512 functions
to be able to decrypt sniffer captures with PMK available from an
external source.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
(Re)Association Response frames should include radio measurement
capabilities in order to let stations know if they can, e.g., use
neighbor requests.
I tested this commit with a Samsung S8, which does not send neighbor
requests without this commit and sends them afterwards.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
A driver supports FT if it either supports SME or the
NL80211_CMD_UPDATE_FT_IES command. When selecting AKM suites,
wpa_supplicant currently doesn't take into account whether or not either
of those conditions are met. This can cause association failures, e.g.,
when an AP supports both WPA-EAP and FT-EAP but the driver doesn't
support FT (wpa_supplicant will decide to do FT-EAP since it is unaware
the driver doesn't support it). This change allows an FT suite to be
selected only when the driver also supports FT.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
The new sae_pwe=3 mode can be used to test non-compliant behavior with
SAE Password Identifiers. This can be used to force use of
hunting-and-pecking loop for PWE derivation when Password Identifier is
used. This is not allowed by the standard and as such, this
functionality is aimed at compliance testing.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This was not supposed to set the constructed bit in the header. Fix this
to avoid parsing issues with other ASN.1 DER parsers.
Fixes: c025c2eb59 ("DPP: DPPEnvelopedData generation for Configurator backup")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make Configurator provisioning require explicit conf parameter enabling
similarly to the previously used conf=ap-* and conf=sta-* cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This avoids unexpected behavior if GAS query fails and the Config
Response does not get processed at all. Previously, this could result in
configuration being assumed to be successful instead of failure when
Config Response object was not received at all. That could result in
undesired Config Result frame transmission with DPP Rel 2 and not
clearing the ongoing DPP session.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, unexpected Authentication Confirm messages were ignored in
cases where no Authentication Confirm message was expected at all, but
if this message was received twice in a state where it was expected, the
duplicated version was also processed. This resulted in unexpected
behavior when authentication result was processed multiple times (e.g.,
two instances of GAS client could have been started).
Fix this by checking auth->waiting_auth_conf before processing
Authetication Confirm. That boolean was already tracked, but it was used
only for other purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Only one peer-commit-scalar value was stored for a specific STA (i.e.,
one per MAC address) and that value got replaced when the next SAE
Authentication exchange was started. This ended up breaking the check
against re-use of peer-commit-scalar from an Accepted instance when
anti-clogging token was requested. The first SAE commit message (the one
without anti-clogging token) ended up overwriting the cached
peer-commit-scalar value while leaving that instance in Accepted state.
The second SAE commit message (with anti-clogging token) added ended up
getting rejected if it used the same value again (and re-use is expected
in this particular case where the value was not used in Accepted
instance).
Fix this by using a separate pointer for storing the peer-commit-scalar
value that was used in an Accepted instance. There is no need to
allocate memory for two values, i.e., it is sufficient to maintain
separate pointers to the value and move the stored value to the special
Accepted state pointer when moving to the Accepted state.
This fixes issues where a peer STA ends up running back-to-back SAE
authentication within couple of seconds, i.e., without hostapd timing
out the STA entry for a case where anti-clogging token is required.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, hostapd ignored the secondary channel provided by ACS if
both HT40+ and HT40- are set in hostapd.conf. This change selects such
channel for HT40 if it's valid, which is more reasonable.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The internal WMM AC parameters use just the exponent of the CW value,
while nl80211 reports the full CW value. This led to completely bogus
CWmin/CWmax values in the WMM IE when a regulatory limit was present.
Fix this by converting the value to the exponent before passing it on.
Fixes: 636c02c6e9 ("nl80211: Add regulatory wmm_limit to hostapd_channel_data")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
nl80211 uses a different queue mapping from hostap, so AC indexes need
to be converted.
Fixes: 636c02c6e9 ("nl80211: Add regulatory wmm_limit to hostapd_channel_data")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The size of a single route(4) message cannot be derived from
either the size of the AF_INET or AF_INET6 routing tables.
Both could be empty or very large.
As such revert back to a buffer size of 2048 which mirrors
other programs which parse the routing socket.
Signed-off-by: Roy Marples <roy@marples.name>
Now that both hostapd and wpa_supplicant react to interface flag
changes, there is no need to set or remove IFF_UP.
It should be an administrative flag only.
Signed-off-by: Roy Marples <roy@marples.name>
There is little point in having both and it brings interface
addition/removal and IFF_UP notifications to hostapd.
Signed-off-by: Roy Marples <roy@marples.name>
When external authentication is used, the station send mlme frame (auth)
to the driver may not be able to get the frequency (bss->freq) after
hostap.git commit b6f8b5a9 ("nl80211: Update freq only when CSA
completes"). Use the assoc_freq to send the MLME frame when SAE external
authentication is used to avoid this issue.
Signed-off-by: Ouden <Ouden.Biz@gmail.com>
This commit introduces additional stats to query through
QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds support for generating an encrypted backup of the local
Configurator information for the purpose of enrolling a new
Configurator. This includes all ASN.1 construction and data encryption,
but the configuration and connector template values in
dpp_build_conf_params() are not yet complete.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process the received DPPEnvelopedData when going through Configurator
provisioning as the Enrollee (the new Configurator). This parses the
message, derives the needed keys, and decrypts the Configurator
parameters. This commit stores the received information in
auth->conf_key_pkg, but the actually use of that information to create a
new Configurator instance will be handled in a separate commit.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
There is no need for the Protocol Version attribute in Authentication
Response if the peer is a DPP R1 device since such device would not know
how to use this attribute. To reduce risk for interoperability issues,
add this new attribute only if the peer included it in Authentication
Request.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY_FREQUENCY for
primary channel center frequency in the definition for Representative
Tx Power List (RTPL) list entry instance. This is required for 6 GHz
support, since the 6 GHz channel numbers overlap with existing 2.4 GHz
and 5 GHz channel numbers thus requiring frequency values to uniquely
identify channels.
Mark QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY as deprecated if both the
driver and user space application support 6 GHz. For backward
compatibility, QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY is still used if
either the driver or user space application or both do not support the
6 GHz band.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The recent addition of the X.509v3 certificatePolicies parser had a
copy-paste issue on the inner SEQUENCE parser that ended up using
incorrect length for the remaining buffer. Fix that to calculate the
remaining length properly to avoid reading beyond the end of the buffer
in case of corrupted input data.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=20363
Fixes: d165b32f38 ("TLS: TOD-STRICT and TOD-TOFU certificate policies")
Signed-off-by: Jouni Malinen <j@w1.fi>
Make the selected channel available for upper layer software to use,
e.g., when starting DPP listen operation during NFC negotiated
connection handover.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new control interface commands "DPP_NFC_HANDOVER_REQ own=<id>
uri=<URI>" and "DPP_NFC_HANDOVER_SEL own=<id> uri=<URI>" to support NFC
negotiated connection handover. These commands are used to report a DPP
URI received from a peer NFC Device in Handover Request and Handover
Select messages. The commands return peer bootstrapping information ID
or FAIL on failure. The returned ID is used similarly to any other
bootstrapping information to initiate DPP authentication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new dpp_gen_uri() helper function can be used to build the
bootstrapping URI from locally stored information. This can be used to
make it easier to update the URI, e.g., for NFC negotiated connection
handover cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This increases the limit of how many data fragments can be supported
with the internal HMAC implementation. The previous limit was hit with
some FT use cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit introduces the vendor event
QCA_NL80211_VENDOR_SUBCMD_REQUEST_SAR_LIMITS_EVENT.
Host drivers can request user space application to set SAR power
limits with this event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new QCA vendor attribute to set thermal level to the driver from
userspace. The driver/firmware takes actions requested by userspace to
mitigate high temperature such as throttling TX etc. The driver may
choose the level of throttling and other actions for various thermal
levels set by userspace.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Initial OWE implementation used SHA256 when deriving the PTK for all OWE
groups. This was supposed to change to SHA384 for group 20 and SHA512
for group 21. The new owe_ptk_workaround=1 network parameter can be used
to enable older behavior mainly for testing purposes. There is no impact
to group 19 behavior, but if enabled, this will make group 20 and 21
cases use SHA256-based PTK derivation which will not work with the
updated OWE implementation on the AP side.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Initial OWE implementation used SHA256 when deriving the PTK for all OWE
groups. This was supposed to change to SHA384 for group 20 and SHA512
for group 21. The new owe_ptk_workaround parameter can be used to enable
workaround for interoperability with stations that use SHA256 with
groups 20 and 21. By default, only the appropriate hash function is
accepted. When workaround is enabled (owe_ptk_workaround=1), the
appropriate hash function is tried first and if that fails, SHA256-based
PTK derivation is attempted. This workaround can result in reduced
security for groups 20 and 21, but is required for interoperability with
older implementations. There is no impact to group 19 behavior.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previous implementation was hardcoding use of SHA256 PMK-to-PTK
derivation for all groups. Replace that with hash algorithm selection
based on the length of the prime similarly to the way this was done for
other derivation steps in OWE.
This breaks backwards compatibility when using group 20 or 21; group 19
behavior remains same.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous commit had a rebasing issue that ended up covering only the
center_segment0 != 0 case. These were supposed to apply for all 6 GHz
band cases.
Fixes: 0bfc04b8d0 ("Do not enable HT/VHT when operating in 6 GHz band")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE P802.11-REVmd was modified to use a container IE for anti-clogging
token whenver H2E is used so that parsing of the SAE Authentication
frames can be simplified.
See this document for more details of the approved changes:
https://mentor.ieee.org/802.11/dcn/19/11-19-2154-02-000m-sae-anti-clogging-token.docx
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Some things in bfd.h that we use were renamed, and in the case of
bfd_get_section_vma() a parameter was dropped. Work around this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for EAP method prefix in the anonymous identity
used during EAP-SIM/AKA/AKA' authentication when encrypted IMSI
is used. The prefix is a single character that indicates which
EAP method is required by the client.
Signed-off-by: Hai Shalom <haishalom@google.com>
Based on the now documented seg0/seg1 values from offloaded ACS, there
is a mismatch between the driver interface and internal hostapd use.
The value of segment0 field in ACS results is the index of the channel
center frequency for 20 MHz, 40 MHz, and 80M Hz channels. The value is
the center frequency index of the primary 80 MHz segment for 160 MHz and
80+80 MHz channels.
The value of segment1 field in ACS results is zero for 20 MHz, 40 MHz,
and 80 MHz channels. The value is the index of the channel center
frequency for 160 MHz channels and the center frequency index of the
secondary 80 MHz segment for 80+80 MHz channels.
However, in struct hostapd_config, for 160 MHz channels, the value of
the segment0 field is the index of the channel center frequency of 160
MHz channel and the value of the segment1 field is zero. Map the values
from ACS event into hostapd_config fields accordingly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update the documentation with values to be sent for seg0 and seg1 fields
in external ACS result event for 20 MHz, 40 MHz, 80 MHz, 160 MHz, and
80+80 MHz channels. These values match the changes done to definitions
of seg0 and seg1 fields in the IEEE 802.11 standard.
This vendor command had not previously been documented in this level of
detail and had not actually been used for the only case that could have
two different interpretation (160 MHz) based on which version of IEEE
802.11 standard is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The Channel Width field value is 0 for 20 MHz, 1 for 40 MHz, 2 for 80
MHz, and 3 for both 160 MHz and 80+80 MHz channels. The 80+80 MHz case
was not addressed previously correctly since it cannot be derived from
seg0 only.
The Channel Center Frequency Segment 0 field value is the index of
channel center frequency for 20 MHz, 40 MHz, and 80 MHz channels. The
value is the center frequency index of the primary 80 MHz segment for
160 MHz and 80+80 MHz channels.
The Channel Center Frequency Segment 1 field value is zero for 20 MHz,
40 MHz, and 80 MHz channels. The value is the index of the channel
center frequency for 160 MHz channel and the center frequency index of
the secondary 80 MHz segment for 80+80 MHz channels.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make the dummy hostapd_hw_mode_txt() wrapper return "UNKNOWN" instead of
NULL to avoid a warning from a debug printf using %s with NULL.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add the new set_key() parameter "key_flag" to provide more specific
description of what type of a key is being configured. This is needed to
be able to add support for "Extended Key ID for Individually Addressed
Frames" from IEEE Std 802.11-2016. In addition, this may be used to
replace the set_tx boolean eventually once all the driver wrappers have
moved to using the new key_flag.
The following flag are defined:
KEY_FLAG_MODIFY
Set when an already installed key must be updated.
So far the only use-case is changing RX/TX status of installed
keys. Must not be set when deleting a key.
KEY_FLAG_DEFAULT
Set when the key is also a default key. Must not be set when
deleting a key. (This is the replacement for set_tx.)
KEY_FLAG_RX
The key is valid for RX. Must not be set when deleting a key.
KEY_FLAG_TX
The key is valid for TX. Must not be set when deleting a key.
KEY_FLAG_GROUP
The key is a broadcast or group key.
KEY_FLAG_PAIRWISE
The key is a pairwise key.
KEY_FLAG_PMK
The key is a Pairwise Master Key (PMK).
Predefined and needed flag combinations so far are:
KEY_FLAG_GROUP_RX_TX
WEP key not used as default key (yet).
KEY_FLAG_GROUP_RX_TX_DEFAULT
Default WEP or WPA-NONE key.
KEY_FLAG_GROUP_RX
GTK key valid for RX only.
KEY_FLAG_GROUP_TX_DEFAULT
GTK key valid for TX only, immediately taking over TX.
KEY_FLAG_PAIRWISE_RX_TX
Pairwise key immediately becoming the active pairwise key.
KEY_FLAG_PAIRWISE_RX
Pairwise key not yet valid for TX. (Only usable with Extended Key ID
support.)
KEY_FLAG_PAIRWISE_RX_TX_MODIFY
Enable TX for a pairwise key installed with KEY_FLAG_PAIRWISE_RX.
KEY_FLAG_RX_TX
Not a valid standalone key type and can only used in combination
with other flags to mark a key for RX/TX.
This commit is not changing any functionality. It just adds the new
key_flag to all hostapd/wpa_supplicant set_key() functions without using
it, yet.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
This is the function that actually uses the parameters, so pass the full
parameter struct to it instead of hiding the struct from it in the
simple wrapper.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the driver supports VLAN offload mechanism with a single netdev, use
that instead of separate per-VLAN netdevs.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
Add indication for driver VLAN offload capability and configuration of
the VLAN ID to the driver.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
This is in preparation for adding support to use a single WLAN netdev
with VLAN operations offloaded to the driver. No functional changes are
included in this commit.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
This makes it more convenient to add, remove, and modify the parameters
without always having to update every single driver_*.c implementation
of this callback function.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
sae_confirm_immediate=2 can now be used in CONFIG_TESTING_OPTIONS=y
builds to minimize the latency between SAE Commit and SAE Confirm by
postponing transmission of SAE Commit until the SAE Confirm frame is
generated. This does not have significant impact, but can get the frames
tiny bit closer to each other over the air to increase testing coverage.
The only difference between sae_confirm_immediate 1 and 2 is in the
former deriving KCK, PMK, PMKID, and CN between transmission of the
frames (i.e., a small number of hash operations).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Correct the check for presence of
QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL attribute before using it
while processing acs_result event.
Fixes: 857d94225a ("Extend offloaded ACS QCA vendor command to support VHT")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Test: wpa_supplicant module tests
../src/utils/utils_module_tests.c:933:7: runtime error: left shift of 1 by 31 places cannot be represented in type 'int'
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Returned policies from X509_get_ext_d2i() need to be freed.
Fixes: 21f1a1e66c ("Report TOD policy")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is mainly for testing purposes to allow wpa_supplicant and hostapd
functionality to be tested both with and without using the nl80211
control port which is by default used whenever supported by the driver.
control_port=0 driver parameter will prevent that from happening.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows EAPOL frames to be received over the separate controlled
port once rest of the driver interface is ready for this. By itself,
this commit does not actually change behavior since cfg80211 will not be
delivering these events without them being explicitly requested.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
In order to correctly encrypt rekeying frames, wpa_supplicant now checks
if a PTK is currently installed and sets the corresponding encrypt
option for tx_control_port().
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Linux kernel v4.17 added the ability to request sending controlled port
frames (e.g., IEEE 802.1X controlled port EAPOL frames) via nl80211
instead of a normal network socket. Doing this provides the device
driver with ordering information between the control port frames and the
installation of keys. This empowers it to avoid race conditions between,
for example, PTK replacement and the sending of frame 4 of the 4-way
rekeying handshake in an RSNA. The key difference between the specific
control port and normal socket send is that the device driver will
certainly get any EAPOL frames comprising a 4-way handshake before it
gets the key installation call for the derived key. By flushing its TX
buffers it can then ensure that no pending EAPOL frames are
inadvertently encrypted with a key that the peer will not yet have
installed.
Add a CONTROL_PORT flag to the hostap driver API to report driver
capability for using a separate control port for EAPOL frames. This
operation is exactly like an Ethernet send except for the extra ordering
information it provides for device drivers. The nl80211 driver is
updated to support this operation when the device reports support for
NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211. Also add a driver op
tx_control_port() for request a frame to be sent over the controlled
port.
Signed-off-by: Brendan Jackman <brendan.jackman@bluwireless.co.uk>
This was used only for FT RRB sending with driver_test.c and
driver_test.c was removed more than five years ago, so there is no point
in continuing to maintain this driver op.
Signed-off-by: Jouni Malinen <j@w1.fi>
Application Extension attribute is defined in WSC tech spec v2.07 page
104. Allow hostapd to be configured to add this extension into WPS IE in
Beacon and Probe Response frames. The implementation is very similar to
vendor extension.
A new optional entry called "wps_application_ext" is added to hostapd
config file to configure this. It enodes the payload of the Application
Extension attribute in hexdump format.
Signed-off-by: Veli Demirel <veli.demirel@airties.com>
Signed-off-by: Bilal Hatipoglu <bilal.hatipoglu@airties.com>
Since NL80211_CMD_FRAME does not allow encryption to be disabled for the
frame, add a monitor interface temporarily for cases where this type of
no-encrypt frames are to be sent. The temporary monitor interface is
removed immediately after sending the frame.
This is testing functionality (only in CONFIG_TESTING_OPTIONS=y builds)
that is used for PMF testing where the AP can use this to inject an
unprotected Robust Management frame (mainly, Deauthentication or
Disassociation frame) even in cases where PMF has been negotiated for
the association.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd gtk_rsc_override and igtk_rsc_override configuration
parameters can be used to set an override value for the RSC that the AP
advertises for STAs for GTK/IGTK. The contents of those parameters is a
hexdump of the RSC in little endian byte order.
This functionality is available only in CONFIG_TESTING_OPTIONS=y builds.
This can be used to verify that stations implement initial RSC
configuration correctly for GTK/ and IGTK.
Signed-off-by: Jouni Malinen <j@w1.fi>
I saw a case where the kernel's cfg80211 rejected hostapd's attempt to
send a neighbor report response because nl80211 flagged the frame as
offchannel-OK, but kernel rejects because channel was 100 (DFS) and so
kernel failed thinking it was constrained by DFS/CAC requirements that
do not allow the operating channel to be left (at least in FCC).
Don't set the packet as off-channel OK if we are transmitting on the
current operating channel of an AP to avoid such issues with
transmission of Action frames.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This is to match the NL80211_CMD_ACTION renaming to NL80211_CMD_FRAME
that happened long time ago. This command can be used with any IEEE
802.11 frame and it should not be implied to be limited to Action
frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace a separate cookie_out pointer argument with save_cookie boolean
since drv->send_action_cookie is the only longer term storage place for
the cookies. Merge all nl80211_send_frame_cmd() callers within
wpa_driver_nl80211_send_mlme() to use a single shared call to simplify
the function.
Signed-off-by: Jouni Malinen <j@w1.fi>
Merge this function into wpa_driver_nl80211_send_mlme() that is now the
only caller for the previously shared helper function. This is a step
towards cleaning up the overly complex code path for sending Management
frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
All the previous users have now been converted to using send_mlme() so
this unused send_frame() callback can be removed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since send_mlme() now has support for the no_encrypt argument it is
possible to get rid of the remaining send_frame() uses.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows send_mlme() to be used to replace send_frame() for the test
cases where unencrypted Deauthentication/Disassociation frames need to
be sent out even when using PMF for the association. This is currently
supported only when monitor interface is used for AP mode management
frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Merge hostapd_drv_send_mlme_csa() functionality into
hostapd_drv_send_mlme() to get a single driver ops handler function for
hostapd. In addition, add a new no_encrypt parameter in preparation for
functionality that is needed to get rid of the separate send_frame()
driver op.
Signed-off-by: Jouni Malinen <j@w1.fi>
send_frame() is documented to be used for "testing use only" and as
such, it should not have used here for a normal production
functionality. Replace this with use of send_mlme() which is already
used for sending Deauthentication frames in other cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Call nl80211_send_monitor() directly instead of going through
wpa_driver_nl80211_send_frame() for the case where monitor interface is
used for AP mode management purposes. drv->use_monitor has to be 1 in
this code path, so wpa_driver_nl80211_send_frame() was calling
nl80211_send_monitor() unconditionally for this code path and that extra
function call can be removed here to simplify the implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
Netlink dump message may be interrupted if an internal inconsistency is
detected in the kernel code. This can happen, e.g., if a Beacon frame
from the current AP is received while NL80211_CMD_GET_SCAN is used to
fetch scan results. Previously, such cases would end up not reporting an
error and that could result in processing partial data.
Modify this by detecting this special interruption case and converting
it to an error. For the NL80211_CMD_GET_SCAN, try again up to 10 times
to get the full response. For other commands (which are not yet known to
fail in similar manner frequently), report an error to the caller.
Signed-off-by: Jouni Malinen <j@w1.fi>
libnl functions return a library specific error value in libnl 2.0 and
newer. errno is not necessarily valid in all error cases and strerror()
for the returned value is not valid either.
Use nl_geterror() to get the correct error string from the returned
error code.
Signed-off-by: Jouni Malinen <j@w1.fi>
libnl functions return a library specific error value. errno is not
necessarily valid in all error cases and strerror() for the returned
value is not valid either.
Use nl_geterror() to get the correct error string from the returned
error code.
Signed-off-by: Jouni Malinen <j@w1.fi>
This simplifies code by not having to maintain and come up with new
backwards compatibility wrappers for a library release from 12 years
ago.
Signed-off-by: Jouni Malinen <j@w1.fi>
These are certainly not error conditions, but normal cases for starting
up. Drop the message from ERROR to DEBUG.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add PMKSA candidates from scan results only if they advertise an AKMP
that is used with RSN pre-authentication. Previously, candidates were
added but then ignored later if the AKMP was not suitable.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit changes the failover behavior of RADIUS client. Commit
27ebadccfb ("RADIUS client: Cease endless retry for message for
multiple servers") changed the retry logic, causing RADIUS client to
wait RADIUS_CLIENT_NUM_FAILOVER + 1 timeouts before failing over the
first time. Prior to that commit, RADIUS client would wait
RADIUS_CLIENT_NUM_FAILOVER timeouts before each failover. This was
caused by moving the entry->attempts > RADIUS_CLIENT_NUM_FAILOVER
comparison to before the retry attempt, where entry->attempts is
incremented.
The commit in question set entry->attempts in radius_change_server to 1
instead of 0, so RADIUS client would still only wait
RADIUS_CLIENT_NUM_FAILOVER timeouts for subsequent failovers, the same
as the original behavior.
This commit changes the comparison so the initial failover now happens
after waiting RADIUS_CLIENT_NUM_FAILOVER timeouts, as it did originally.
It also changes the RADIUS_CLIENT_MAX_FAILOVER comparison to prevent an
additional attempt to the primary server after the final failover.
Signed-off-by: Ethan Everett <ethan.everett@meraki.net>
Add function that returns whether WoWLAN has been enabled for the device
or not.
Signed-off-by: Alfonso Sanchez-Beato <alfonso.sanchez-beato@canonical.com>
ieee802_11_allowed_address() did not really do anything useful for the
call from handle_probe_req(), so replace that with a direct call to
hostapd_allowed_address() and make ieee802_11_allowed_address() a static
function.
Signed-off-by: Jouni Malinen <j@w1.fi>
When returning from handle_auth() after ieee802_11_allowed_address()
returned HOSTAPD_ACL_ACCEPT, but before ieee802_11_set_radius_info() has
been called, identity, radius_cui, and psk might not have been consumed.
Fix this by avoiding the need to free these variables at all.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
For FT protocol to work, the BSSs need to be operating an FT AKM with
the same SSID and mobility domain. The previous commit covered the
mobility domain, this covers the other prerequisites. This reduces
unnecessary load from having to allocate queued messages for interfaces
that cannot have valid data.
Signed-off-by: Jouni Malinen <j@w1.fi>
Fast BSS Transition requires related APs operating in the same mobility
domain. Therefore, we can check whether the local managed BSS is
operating the same mobility domain before sending multicast/unicast
messages to it. This reduces unnecessary load from having to allocate
queued messages for interfaces that cannot have valid data.
Signed-off-by: Jinglin Wang <bryanwang@synology.com>
Signed-off-by: MinHong Wang <minhongw@synology.com>
This makes it easier to figure out how frames are delivered directly
between BSSs operated within a single hostapd process.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add new messages to the end of the l2_oui_queue instead of inserting
them at the beginning so that the dl_list_for_each_safe() iteration in
hostapd_oui_deliver_later() goes through the messages in the same order
they were originally queued.
Signed-off-by: Jouni Malinen <j@w1.fi>
When using FT wildcard feature, the inter-AP protocol will send
broadcast messages to discover related APs.
For example,
12/6 16:24:43 FT: Send PMK-R1 pull request to remote R0KH address
ff:ff:ff:ff:ff:ff
12/6 16:24:43 FT: Send out sequence number request to
ff:ff:ff:ff:ff:ff
If you have multiple interfaces/BSSs in a single hostapd process,
hostapd_wpa_auth_oui_iter() returned 1 after the first interface was
processed. Iteration in for_each_interface() will be stopped since it
gets a non-zero return value from hostapd_wpa_auth_oui_iter().
Even worse, the packet will not be sent to ethernet because
for_each_interface() returns non-zero value. hostapd_wpa_auth_send_oui()
will then return data_len immediately.
To prevent this, hostapd_wpa_auth_oui_iter() should not return 1 after
any successful transmission to other interfaces, if the dst_addr of
packet is a multicast address.
Signed-off-by: Jinglin Wang <bryanwang@synology.com>
Signed-off-by: MinHong Wang <minhongw@synology.com>
If the header of a PEM-formatted certificate or key in private_key file
indicates that it is wrapped with a TPM2 key, try to autoload the
appropriate OpenSSL engine that can transparently unwrap the key. This
enables systems to use TPM2-wrapped keys as drop-in replacements to
ordinary SSL keys.
This functionality needs
https://git.kernel.org/pub/scm/linux/kernel/git/jejb/openssl_tpm2_engine.git
to be installed as an OpenSSL engine.
Signed-off-by: Daniel Kobras <kobras@puzzle-itc.de>
ignore_broadcast_ssid=1 (or 2) were practically ignored if the Probe
Request frame included the SSID List or Short SSID List elements. Fix
this by requiring exact SSID match whenever ignore_broadcast_ssid is in
use regardless how SSID parameters are set in the Probe Request frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
According to IEEE P802.11ax/D6.0, 11.1.4.3.4 (Criteria for sending a
response), AP should answer Probe Request frames if either SSID or Short
SSID matches. Implement this part of the Short SSID use for the BSS (the
collocated 6 GHz BSS case is not covered in this commit).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This can be used in the future to implement support for RNR and scanning
extensions using a shorter field for the SSID.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
We use the wired driver for wired port authentication with a slight
extension to add the port into a bridge upon successful authentication
and to remove it from the bridge when the session terminates.
Our expectation was that the Session-Timeout configuration at the RADIUS
server is respected, i.e. the session is terminated and would need
re-authentication - like it is working for WLAN sessions over the
nl80211 driver. Alas, it turned out the session is not terminated with
the wired driver.
It turned out that when ap_handle_session_timer() is executed, the
sta->flags of the wired port has only the WLAN_STA_AUTHORIZED bit set.
The WLAN_STA_AUTH bit, which is used to check whether the STA needs to
be de-authenticated, is missing.
Extend the check for any of the WLAN_STA_(AUTH | ASSOC | AUTHORIZED)
bits to solve this issue with the wired driver. That should not have any
side-effect for the WLAN cases since WLAN_STA_AUTH is expected to always
be set for those when there is an ongoing session and separate checks
for ASSOC and AUTHORIZED don't change this.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
If hostapd or wpa_supplicant is started with both -s and -f command line
arguments, debug log ended up being written only into syslog and the log
file was left empty. Change this so that the log entries will be written
to both places. Either -s or -f (or both) results in debug log to stdout
being disabled which was already the case.
Signed-off-by: Jouni Malinen <j@w1.fi>
This lets one know the current neighbor list, and could be used
to populate the neighbor list of other hostapd processes.
For instance:
$ hostapd_cli -i vap0001 show_neighbor
04:f0:21:1e:ae:b0 ssid=04f0211eaeb0af190000802809 nr=04f0211eaeb0af1900008028090603022a00
$ hostapd_cli -i vap0000 set_neighbor 04:f0:21:1e:ae:b0 ssid=04f0211eaeb0af190000802809 nr=04f0211eaeb0af1900008028090603022a00
OK
$ hostapd_cli -i vap0000 show_neighbor
04:f0:21:1e:ae:b0 ssid=04f0211eaeb0af190000802809 nr=04f0211eaeb0af1900008028090603022a00
04:f0:21:c3:b2:b0 ssid=04f021c3b2b0af190000802809 nr=04f021c3b2b0af1900008028090603022a00
Signed-off-by: Ben Greear <greearb@candelatech.com>
Move this implementation from check_40mhz_2g4() into a new helper
function check_bss_coex_40mhz function() so that it can be used in the
station mode case as well as the previously used AP mode case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Support for dynamic VLANs depends on the Linux bridge ioctls.
Add this dependency explicitely to drivers make files.
This fixes build for minimal hostapd configs such as:
CONFIG_DRIVER_WIRED=y
CONFIG_FULL_DYNAMIC_VLAN=y
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
WPS_EVENT_CANCEL is added to indicate cancellation of a WPS operation
for any reason in hostapd/wpa_supplicant.
WPS_EVENT_PIN_ACTIVE is added to indicate when a PIN operation is
triggered in wpa_supplicant.
Signed-off-by: Veli Demirel <veli.demirel@airties.com>
Signed-off-by: Bilal Hatipoglu <bilal.hatipoglu@airties.com>
Normally nl80211 driver will attempt to strictly control what bridge
given interface is put in. It'll attempt to remove it from an existing
bridge if it doesn't match the configured one. If it's not in a bridge
it'll try to put it into one. If any of this fails then hostapd will
bail out and not set up the BSS at all.
Arguably that's reasonable since it allows to set the BSS up coherently
with regard to EAPOL handling as well as allows extra interactions with
things like FDB. However, not all hostapd drivers interact with bridge=
the same way. One example is atheros. Therefore it's not clear what the
desired behavior should be if consistency across drivers is considered.
There's a case where one might want to use a non-native Linux bridge,
e.g., openvswitch, in which case regular ioctls won't work to put an
interface into a bridge, or figure out what bridge an interface is in.
The underlying wireless driver can still be an ordinary nl80211 driver.
This change relaxes the bridge setup failure so that hostapd still
starts even if it fails to add an interface into a configured bridge
name. It still sets up all the necessary sockets (including the
configured bridge=) so EAPOL handling should work fine. This then leaves
it to the system integrator to manage wireless interface as bridge ports
and possibly fdb hints too.
Signed-off-by: Michal Kazior <michal@plume.com>
In repeater configuration, both AP and STA wireless interfaces may be
included into the same bridge. In this case the following race condition
may occur: wpa_supplicant and hostapd are started, then hostapd clients
are connected before wpa_supplicant connects to remote AP. EAPOL packets
between hostapd and its clients are detected by wpa_supplicant on bridge
interface, prematurely disabling the workaround.
One possible option to fix this issue is to check EAPOL destination MAC
in wpa_supplicant and disable workaround only if EAPOL packet on bridge
interface is indeed intended for wpa_supplicant.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
This buffer was getting corrupted, so add more details to make it
clearer what causes the corruption should this type of regression show
up again.
Signed-off-by: Jouni Malinen <j@w1.fi>
The case where the old RSNE included one or more PMKIDs and that RSNE
was followed by another IE was handled incorrectly since the
os_memmove() to move the end of the buffer when removing old PMKIDs was
stopping copying at the end of the RSNE, not the end of the IE buffer.
This could result in corrupting the IE that followed the RSNE. In
practice, this broke FT-SAE with H2E by corrupting the RSNXE that is in
the buffer after the RSNE.
Fix this by copying the full end of the buffer (i.e., including the
following RSNXE in the visible error case) when removing the old PMKIDs.
Signed-off-by: Jouni Malinen <j@w1.fi>
EAP-SIM full authentication starts with one or more SIM/Start rounds, so
reject an unexpected SIM/Challenge round without any preceeding
SIM/Start rounds to avoid unexpected behavior. In practice, an attempt
to start with SIM/Challenge would have resulted in different MK being
derived and the Challenge message getting rejected due to mismatching
AT_MAC unless the misbehaving server has access to valid Kc, so the end
result is identical, but it is cleaner to reject the unexpected message
explicitly to avoid any risk of trying to proceed without NONCE_MT.
Signed-off-by: Jouni Malinen <j@w1.fi>
These ciphers do not use a separate MAC algorithm, so digest nid will be
NID_undef. In addition, the fixed_iv_length needs to be set to 4 which
is the implicit part of the IV from PRF. This is needed to fix EAP-FAST
key derivation for cases where GCM/CCM ciphers are used for TLS.
Signed-off-by: Jouni Malinen <j@w1.fi>
EAPOL-Key message 1/4 without PMKID KDE was sent with 22 bytes of stray
data following a zero length key data field. These 22 bytes happens to
be the exact size of an PMKID KDE. Strip these trailing bytes by
checking whether a PMKID is available and adjust pmkid_len to 0 if not.
This was seen for example in capture files created by hwsim test case
suite_b_192 but code modified to handle also the other cases without
PMKID (Suite B no-KCK, FILS without PMKID available, SAE without PMKID
available).
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sony.com>
It was possible for the driver to advertise support for channels that
are not found from wpa_supplicant frequency-to-channel mapping (e.g.,
channel 182 at 5910 MHz) and that resulted in not initializing the
channel number information. Fix this by explicitly clearing the full
struct hostapd_channel_data buffer before parsing the information into
it from the driver.
This avoids some conditional jumps that could have dependent on
uninitialized values.
Signed-off-by: Jouni Malinen <j@w1.fi>
openssl engines may dynamically load external libraries. Our event_*()
functions happen to be named very generically, such that event_add()
collides with the libevent library (https://libevent.org/). This can
have disastrous effects (esp. when using CONFIG_WPA_TRACE, which enables
partial linking) when our SSL engines call into the WPS event_add()
instead of their intended libevent event_add().
Resolve this by providing a more unique prefix to these functions.
Rename performed via:
sed -i -E \
's:\<event_(add|delete_all|send_all_later|send_stop_all)\>:wps_upnp_event_\1:g' \
$(git grep -l event_)
Tested via (among other things) hwsim '-f ap_wps' module.
Signed-off-by: Brian Norris <briannorris@chromium.org>
On failure of json_alloc_token(), json_parse() can return without
freeing 'str' previously allocated by json_parse_string(). Fix this
adding proper call to os_free().
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
Fix a memory leak exposed by the dpp_own_config_sign_fail test.
Fixes: 52d469de11 ("DPP2: Support multiple Config Objects in Enrollee")
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Add a QCA vendor subcommand QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO with
attributes defined in enum qca_wlan_vendor_attr_get_sta to get
information for a BSS in STA mode or for a peer STA in AP mode. This
vendor sub command can be used to get STA information from the driver to
userspace. The attributes defined in enum
qca_wlan_vendor_attr_get_sta_info are used to encapsulate required
information.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Use op_class to derive channel width for the operating channel when
op_class is configured by the user in both fixed channel and ACS cases.
We can avoid using ht_capab field to derive channel width especially in
the 6 GHz band in which only HE is supported.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Only HE mode is allowed in the 6 GHz band hence do not enable HT/VHT
even if they are configured by the user.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support to exclude non-PSC 6 GHz channels from the input frequency
list to ACS. The new acs_exclude_6ghz_non_psc=1 parameter can be used by
6 GHz only APs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The channel numbers are duplicated between 2.4 GHz / 5 GHz bands and 6
GHz band. Hence, add support to configure a list of frequencies to ACS
(freqlist) instead of a list of channel numbers (chanlist). Also, both 5
GHz and 6 GHz channels are referred by HOSTAPD_MODE_IEEE80211A. The 6
GHz channels alone can be configured by using both mode and frequency
list.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Using the channel parameter for validating allowed channel combinations
is not scalable to add 6 GHz support in the future since channel numbers
are duplicated between 2.4 GHz / 5 GHz bands and 6 GHz band. Hence use
frequency field for all channel combination validation steps done before
starting AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
After receiving ACS offload results, select the current hw_mode based on
the frequency selected by the ACS algorithm. The current hw_mode will be
further used during other validation steps such as HT capability
validations, DFS validation, etc.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Using channel field while starting AP will cause issues with the new
6GHz band as the channel numbers are duplicated between the different
bands. Populate iface->freq before starting AP so that it can be used
instead of the channel number for all validations that need to be done
while starting AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Replace channel fields with frequency fields in ACS completed event
interface from the driver layer. Use
QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY and
QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY attributes if the driver
includes them in the QCA_NL80211_VENDOR_SUBCMD_DO_ACS event, otherwise
use QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL and
QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL attributes to maintain
backwards compatibility with old drivers.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The 5 GHz channels are stored in one hw_features set with mode
HOSTAPD_MODE_IEEE80211A while the 6 GHz channels will need to stored in
a separate hw_features set (but with same mode HOSTAPD_MODE_IEEE80211A)
due to possibility of different HE capabilities being available between
the 5 GHz and 6 GHz bands.
Search through all hw_features sets whose mode is same as the input mode
while finding channel corresponding to the input frequency in
hw_get_channel_freq().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The 5 GHz channels are stored in one hw_features set with mode
HOSTAPD_MODE_IEEE80211A while the 6 GHz channels will need to stored in
a separate hw_features set (but with same mode HOSTAPD_MODE_IEEE80211A)
due to possibility of different HE capabilities being available between
the 5 GHz and 6 GHz bands.
Iterate through all hw_features sets and populate channels from all
hw_features sets whose hardware mode is matching the configured hardware
mode while preparing the channel list for ACS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows a P2P connection over P802.11ay EDMG channels to achieve the
highest link speed that the standard allows for channel bonding (CB) up
to CB4.
Let each P2P peer add its EDMG channels to the Supported Channels IE
advertised in P2P GO negotiation. Give EDMG channels priority when peers
negotiate for operating channel.
User may add 'edmg' parameter to p2p_connect, p2p_add_group, and
p2p_invite commands to prefer an EDMG channel for the P2P link. User may
also set p2p_go_edmg=1 in wpa_supplicant configuration file to prefer
EDMG.
When EDMG is used, P2P will try to find the highest channel bonding
supported channel that matches the frequency parameter, if the devices
do not support EDMG, the P2P connection will use a legacy (1-6) 60 GHz
channel.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Update new channels in Channel Bonding (CB2 ... CB4) in the 60 GHz band
for different regulatory regions according to the latest draft amendment
IEEE P802.11ay/D5.0.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Add EDMG bandwidth to CHANWIDTH_ defines.
Update API ieee80211_freq_to_channel_ext() to support EDMG bandwidth
for EDMG channels.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
This is mainly for testing purposes to be able to check which groups
a STA reports as having been rejected when using SAE H2E.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The netRole enum is more generic and can be extended to include new
roles (e.g., Configurator) more easily.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
