Allow STA entry to be removed and re-added to the driver with PMF is
used with FT. Previously, this case resulted in cfg80211 rejecting STA
entry update after successful FT protocol use if the association had not
been dropped and it could not be dropped for the PMF case in
handle_auth().
Signed-off-by: Jouni Malinen <j@w1.fi>
Mark own bootstrap information as having been used in NFC negotiated
connection handover and do not accept non-mutual authentication when
processing Authentication Response from the peer when such bootstrapping
information is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Connector alone is not sufficient for authentication during
reconfiguration, so store the netAccessKey as well.
Fixes: e4eb009d98 ("DPP2: Add Connector and C-sign-key in psk/sae credentials for reconfig")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
While the Diffie-Hellman Parameter element is defined in RFC 8110
explicitly for use witht he OWE AKM, it has now been proposed to be used
with another AKM (DPP). Should any other AKM be extended in similar
manner in the future, the check against unexpected use could result in
additional interoperability issues. Remove that and instead, ignore the
unexpected Diffie-Hellman Parameter element if it is included in
(Re)Association Request frame when any other AKM is negotiated.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the Enrollee indicates support for DPP R2 or newer, add Connector and
C-sign-key in psk/sae credentials (i.e., cases where DPP AKM is not
enabled) for reconfiguration. Extend processing of such credentials in
wpa_supplicant network profile addition to handle this new case
correctly by not setting key_mgmt=DPP based on Connector being present,
but by looking at the actual akm value in the config object.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a driver interface event for Beacon frame protection failures.
Report such events over the control interface and send a
WNM-Notification Request frame to the AP as well.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add HE override support under the build parameter CONFIG_HE_OVERRIDES=y.
The disable_he=1 network profile parameter can be used to disable HE.
This requires a fallback to VHT on the 5 GHz band and to HT on the 2.4
GHz band.
There is no nl80211 support for configuring the driver to disable HE, so
for now, this applies only to IBSS and mesh cases.
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
In repeater mode remote AP may request channel switch to a new channel.
Check if DFS is required for the new channel before proceeding with
normal AP operations. Start CAC procedure if radar detection is required
and channel is not yet marked as available.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Add a new hostapd_is_dfs_overlap() helper function to DFS module. This
function tells whether the selected frequency range overlaps with DFS
channels in the current hostapd configuration. Selected frequency reange
is specified by its center frequency and bandwidth.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Rename DFS helper hostapd_config_dfs_chan_available() to
hostapd_is_dfs_chan_available(). Enable access to this helper function
from other hostapd components.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
EVP_PKEY_get0_EC_KEY() was added in OpenSSL 1.1.0, so add a
compatibility wrapper for it when building with OpenSSL 1.0.2.
Fixes: c025c2eb59 ("DPP: DPPEnvelopedData generation for Configurator backup")
Fixes: 7d9e320054 ("DPP: Received Configurator backup processing")
Signed-off-by: Jouni Malinen <j@w1.fi>
The new skip_prune_assoc=1 parameter can be used to configure hostapd
not to prune associations from other BSSs operated by the same process
when a station associates with another BSS. This can be helpful in
testing roaming cases where association and authorization state is
maintained in an AP when the stations returns.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new driver param full_ap_client_state=0 can be used to test
functionality with the driver capability for full AP client state being
forced to be disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use local variables to avoid sm->wpa_auth->conf type of dereferences
where multiple instances within a function can be cleaned up.
Signed-off-by: Jouni Malinen <j@w1.fi>
Drivers that trigger roaming need to know the lifetime and reauth
threshold time of configured PMKSA so that they can trigger full
authentication to avoid unnecessary disconnection. To support this, send
dot11RSNAConfigPMKLifetime and dot11RSNAConfigPMKReauthThreshold values
configured in wpa_supplicant to the driver while configuring a PMKSA.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
The new hostapd configuration parameter dpp_pfs can be used to specify
how PFS is applied to associations. The default behavior (dpp_pfs=0)
remains same as it was previously, i.e., allow the station to decide
whether to use PFS. PFS use can now be required (dpp_pfs=1) or rejected
(dpp_pfs=2).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add definition for HE bit in neighbor report BSSID Information field
from IEEE P802.11ax/D6.0, 9.4.2.36 Neighbor Report element.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
This functionality was repeated for multiple different frames. Use a
shared helper function to avoid such duplication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process the received Presence Announcement frames in Controller. If a
matching bootstrapping entry for the peer is found, initiate DPP
authentication to complete provisioning of the Enrollee.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process the received Presence Announcement frames in AP/Relay. If a
matching bootstrapping entry for the peer is found in a local
Configurator, that Configurator is used. Otherwise, the frame is relayed
to the first configured Controller (if available).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process received Presence Announcement frames and initiate
Authentication exchange if matching information is available on the
Configurator.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new hostapd configuration parameter
dpp_configurator_connectivity=1 to request Configurator connectivity to
be advertised for chirping Enrollees.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wpa_supplicant control interface command "DPP_CHIRP own=<BI
ID> iter=<count>" to request chirping, i.e., sending of Presence
Announcement frames, to be started.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new identifier definitions for presence announcement,
reconfiguration, and certificate enrollment.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"DPP_BOOTSTRAP_SET <ID> <configurator parameters..>" can now be used to
set peer specific configurator parameters which will override any global
parameters from dpp_configurator_params.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a more convenient way of addressing cases where a
Configurator/Controller may store a large number of peer bootstrapping
information instances and may need to manage different configuration
parameters for each peer while operating as the Responder.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Set the global pointer and msg_ctx when allocating struct
dpp_authentication instead of needing to pass these to
dpp_set_configurator().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd (and wpa_supplicant in AP mode) was internally updating the STA
flags on disconnection cases to remove authorization and association.
However, some cases did not result in immediate update of the driver STA
entry. Update all such cases to send out the update to the driver as
well to reduce risk of race conditions where new frames might be
accepted for TX or RX after the port authorization or association has
been lost and configured keys are removed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check whether the Transition Disable KDE is received from an
authenticated AP and if so, whether it contains valid indication for
disabling a transition mode. If that is the case, update the local
network profile by removing the less secure options.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new hostapd configuration parameter transition_disable can now be
used to configure the AP to advertise that use of a transition mode is
disabled. This allows stations to automatically disable transition mode
by disabling less secure network profile parameters.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the OUI Type and bitmap values for Transition Disable KDE. These
will be shared by both the AP and STA implementations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA_WLAN_VENDOR_CFR_NDPA_NDP_ALL in enum
qca_wlan_vendor_cfr_capture_type. This capture type requests all NDPA
NDP frames to be filtered.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd will trigger EDMG auto channel selection by setting
QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED. The 60 GHz driver will be
called to start an auto channel selection and will return the
primary channel and the EDMG channel.
Signed-off-by: Noam Shaked <nshaked@codeaurora.org>
Addition of chan_2ghz_or_5ghz_to_freq() broke 60 GHz ACS, because it
assumes reported ACS channel is on either 2.4 or 5 GHz band. Fix this
by converting chan_2ghz_or_5ghz_to_freq() to a more generic
chan_to_freq(). The new function uses hw_mode to support 60 GHz.
Fixes: 41cac481a8 ("ACS: Use frequency params in ACS (offload) completed event interface")
Signed-off-by: Noam Shaked <nshaked@codeaurora.org>
The parameters that need to be applied are symmetric to those of VHT,
however the validation code needs to be tweaked to check the HE
capabilities.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Enhanced channel frequency response supports capturing of channel status
information based on RX. Define previous CFR as version 1 and enhanced
CFR as version 2. If target supports both versions, two versions can't
be enabled at same time. Extend attributes for enhanced CFR capture in
enum qca_wlan_vendor_peer_cfr_capture_attr.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Support Extended Key ID in wpa_supplicant according to
IEEE Std 802.11-2016 for infrastructure (AP) associations.
Extended Key ID allows to rekey pairwise keys without the otherwise
unavoidable MPDU losses on a busy link. The standard is fully backward
compatible, allowing STAs to also connect to APs not supporting it.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Support Extended Key ID in hostapd according to IEEE Std 802.11-2016.
Extended Key ID allows to rekey pairwise keys without the otherwise
unavoidable MPDU losses on a busy link. The standard is fully backward
compatible, allowing an AP to serve STAs with and without Extended Key
ID support in the same BSS.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
