The vendor command QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY was defined
to carry the list of avoid frequencies that aim to avoid any
interference with other coexistencies. This recommendation was followed
strictly by trying to prevent WLAN traffic on the impacted channels.
This commit refines the expectation of the interface by defining this
avoid channel list to allow minimal traffic but not heavier one. For
example, P2P may still be able to use avoid list frequencies for P2P
discovery and GO negotiation if the actual group can be set up on a not
impact channel.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make it easier to find the new username (and the new serial number from
it) when a user entry is renamed at the conclusion of client certificate
re-enrollment sequence.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support for configuring parameters for the MU EDCA Parameter Set
element per IEEE P802.11ax/D3.0.
Signed-off-by: Siva Mullati <siva.mullati@intel.com>
Start the (EAP request) identifier at an initial random value
as recommended by RFC 3748 in section 4.1 Request and Response
on page 21.
Signed-off-by: Martin Stanislav <ms@uakom.sk>
If the libnl version is not specified explicitly with CONFIG_LIBNL*, try
to check for the most likely case today with pkg-config.
Signed-off-by: Jouni Malinen <j@w1.fi>
Fix compilation issue if we want to build wpa_supplicant without any
wireless connectivity but only with MACSec support via Linux kernel
driver.
Signed-off-by: Andrey Kartashev <a.s.kartashev@gmail.com>
Two recent changes to MKA create a situation where a new MI is generated
every time a SAK Use parameter set is decoded. The first change moved
invalid key detection from ieee802_1x_decode_basic_body() to
ieee802_1x_kay_decode_mpkdu():
commit db9ca18bbf ("mka: Do not ignore MKPDU parameter set decoding failures")
The second change forces the KaY to generate a new MI when an invalid
key is detected:
commit a8aeaf41df ("mka: Change MI if key invalid")
The fix is to move generation of a new MI from the old invalid key
detection location to the new location.
Fixes: a8aeaf41df ("mka: Change MI if key invalid")
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
Upon issuing a connect request we need to indicate that we want the
driver to offload the 802.1X 4-way handshake for us. Indicate it if
the driver capability supports the offload.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Allow drivers to indicate support for offloading 4-way handshake for
either IEEE 802.1X (WPA2-Enterprise; EAP) and/or WPA/WPA2-PSK
(WPA2-Personal) by splitting the WPA_DRIVER_FLAGS_4WAY_HANDSHAKE flag
into two separate flags.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
When an interface is re-enabled after it was disabled during CAC, it
won't ever get active since hostapd is waiting for a CAC_FINISHED while
kernel side is waiting for a CMD_RADAR_DETECT to start a CAC.
This commit checks for a pending CAC when an interface is enabled and if
so restarts its DFS processing.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
If a station is configured to allow only a subset of frequencies for an
association, the supported operating classes may need to be more limited
than what the hardware supports.
Signed-off-by: Ben Greear <greearb@candelatech.com>
If user has disabled HT or VHT, those related operating classes
should not be advertised as supported.
Signed-off-by: Ben Greear <greearb@candelatech.com>
In the previous RADIUS client implementation, when there are multiple
RADIUS servers, we kept trying the next server when the current message
can not be acked. It leads to endless retry when all the RADIUS servers
are down.
Fix this by keeping a counter for the accumulated retransmit attempts
for the message, and guarantee that after all the servers failover
RADIUS_CLIENT_MAX_FAILOVER times the message will be dropped.
Another issue with the previous code was that the decision regarding
whether the server should fail over was made immediately after we send
out the message. This patch guarantees we consider whether a server
needs failover after pending ack times out.
Signed-off-by: Bo Chen<bochen@meraki.com>
This is in preparation for an implementation change that results in this
unreachable server case not incrementing radiusAuthClientAccessRequests.
Signed-off-by: Jouni Malinen <j@w1.fi>
Define QCA vendor command attributes to configure HE +HTC support and
HE operating mode control transmission. This is used to configure the
testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These are not allowed in ISO C++ (and well, not really in ISO C either,
but that does not result in compiler warning without pedantic
compilation).
Since ieee802_11_common.h may end up getting pulled into C++ code for
some external interfaces, it is more convenient to keep it free of these
cases. Pull in ieee802_11_defs.h to get enum phy_type defined and move
enum chan_width to common/defs.h (which was already pulled in into
src/drivers/driver.h and src/common/ieee802_11_common.h).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These checks were repeated in almost every test case, so use helper
functions to get rid of duplicated (copy-pasted) code.
Signed-off-by: Jouni Malinen <j@w1.fi>
Mesh in VHT mode is supposed to be able to use any bandwidth that VHT
supports, but there was no way to set VHT20 although there are
parameters that are supposed to be used. This commit along then previous
commit for VHT_CHANWIDTH_USE_HT makes mesh configuration available to
use any bandwidth with combinations of existing parameters like shown
below.
VHT80:
default
do not set any parameters
VHT40:
max_oper_chwidth = 0
VHT20:
max_oper_chwidth = 0
disable_ht40 = 1
HT40:
disable_vht = 1
HT20:
disable_ht40 = 1
disable HT:
disable_ht = 1
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Channel width in VHT mode refers HT capability when the width goes down
to below 80 MHz, hence add checking HT channel width to its max
operation channel width. So that mesh has capability to select bandwidth
below 80 MHz.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
While the AP is configured to enable both FT-PSK and WPA-PSK, an HP
printer request both AKMs (copied from AP?) in Association Request
frame, but don't add MDIE and don't use FT. This results in the
connection failing.
Next in logs we see:
RSN: Trying to use FT, but MDIE not included
IE - hexdump(len=26): 30 18 01 00 00 0f ac 04 01 00 00 0f ac 04
02 00 00 0f ac 02 00 0f ac 04 00 00
This is seen with some HP and Epson printers. Work around this by
stripping FT AKM(s) when MDE is not present and there is still a non-FT
AKM available.
Signed-off-by: Janusz Dziedzic <janusz@plumewifi.com>
This provides similar features to what was already available for HT
overrides. Probe Request frames look correct, and VHT capabilities shown
in debugfs look as expected.
Signed-off-by: Ben Greear <greearb@candelatech.com>
There is no need to allow symlink dereferencing in these cases where a
file (including directories and sockets) are created by the same
process, so use the safer lchown() variant to avoid leaving potential
windows for something external to replace the file before the chown()
call. The particular locations used here should not have write
permissions enabled for processes with less privileges, so this may not
be needed, but anyway, it is better to make these more restrictive
should there be cases where directory permissions are not as expected
for a good deployment.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Android-specific chmod and chown operations on the client socket
(for communication with wpa_supplicant) did not protect against file
replacement between the bind() and chmod()/chown() calls. If the
directory in which the client socket is created (depends a bit on the
version and platform, but /data/misc/wifi/sockets is commonly used)
allows write access to processes that are different (less privileged)
compared to the process calling wpa_ctrl_open2(), it might be possible
to delete the socket file and replace it with something else (mainly, a
symlink) before the chmod/chown operations occur. This could have
resulted in the owner or permissions of the target of that symlink being
modified.
In general, it would be safest to use a directory which has more limited
write privileges (/data/misc/wifi/sockets normally has 'wifi' group
(AID_WIFI) with write access), but if that cannot be easily changed due
to other constraints, it is better to make wpa_ctrl_open2() less likely
to enable this type of race condition between the operations.
Replace chown() with lchown() (i.e., a version that does not dereference
symlinks) and chmod() with fchmod() on the socket before the bind() call
which is also not going to dereference a symlink (whereas chmod()
would). lchown() is a standard operation, but the fchmod() on the socket
is less so (unspecified behavior in some systems). However, it seems to
work on Linux and in particular, on Android, where this code is
executed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add even more workarounds for cfg80211 regulatory state clearing since
these DFS test cases seem to be the most likely ones to fail due to
country=98 issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add even more workarounds for cfg80211 regulatory state clearing since
these DFS test cases seem to be the most likely ones to fail due to
country=98 issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
While selecting a new channel as a reaction to radar event we need to
take into account supported bandwidth for each channel provided via
nl80211. Without this modification hostapd might select an unsupported
channel that would fail during AP startup.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
While doing automatic channel selection we need to take into account
supported bandwidth for each channel provided via nl80211. Without this
modification hostapd might select an unsupported channel which would
fail during AP startup.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
This adds checks to common code to verify supported bandwidth options
for each channel using nl80211-provided info. No support of additional
modes is added, just additional checks. Such checks are needed because
driver/hardware can declare more strict limitations than declared in the
IEEE 802.11 standard. Without this patch hostapd might select
unsupported channel and that will fail because Linux kernel does check
channel bandwidth limitations.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Add NL80211_FREQUENCY_ATTR_NO_* channel attributes parsing. This is
needed for correct checking if channel is available in a particular
bandwidth.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Add support for 160 MHz BW channels to automatic channel selection
algorithm. Only 36 and 100 channels are supported as 160 MHz channels.
Signed-off-by: Dmitry Lebed <lebed.dmitry@gmail.com>
Add even more workarounds for cfg80211 regulatory state clearing since
these WNM test cases seem to be the most likely ones to fail due to
country=98 issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_s->bss_tm_status is within #ifdef CONFIG_WNM, so need to access it
through matching condition.
Fixes: 80d06d0ca9 ("dbus: Export BSS Transition Management status")
Signed-off-by: Jouni Malinen <j@w1.fi>
Move to the version used in draft-ietf-emu-eap-tls13-03.txt, i.e.,
include the 0x0D prefix and use a different TLS-Exporter() label string.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some distributions (e.g., Debian) have started introducting systemwide
OpenSSL policies to disable older protocol versions and ciphers
throughout all programs using OpenSSL. This can result in significant
number of interoperability issues with deployed EAP implementations.
Allow explicit wpa_supplicant (EAP peer) and hostapd (EAP server)
parameters to be used to request systemwide policies to be overridden if
older versions are needed to be able to interoperate with devices that
cannot be updated to support the newer protocol versions or keys. The
default behavior is not changed here, i.e., the systemwide policies will
be followed if no explicit override configuration is used. The overrides
should be used only if really needed since they can result in reduced
security.
In wpa_supplicant, tls_disable_tlsv1_?=0 value in the phase1 network
profile parameter can be used to explicitly enable TLS versions that are
disabled in the systemwide configuration. For example,
phase1="tls_disable_tlsv1_0=0 tls_disable_tlsv1_1=0" would request TLS
v1.0 and TLS v1.1 to be enabled even if the systemwide policy enforces
TLS v1.2 as the minimum version. Similarly, openssl_ciphers parameter
can be used to override systemwide policy, e.g., with
openssl_ciphers="DEFAULT@SECLEVEL=1" to drop from security level 2 to 1
in Debian to allow shorter keys to be used.
In hostapd, tls_flags parameter can be used to configure similar
options. E.g., tls_flags=[ENABLE-TLSv1.0][ENABLE-TLSv1.1]
Signed-off-by: Jouni Malinen <j@w1.fi>
TLS v1.3 was already disabled by default for EAP-FAST, EAP-TTLS,
EAP-PEAP, and EAP-TLS, but the unauthenticated client cases of EAP-TLS
-like functionality (e.g., the one used in OSEN) were missed. Address
those EAP types as well in the same way of disabling TLS v1.3 by default
for now to avoid functionality issues with TLS libraries that enable TLS
v1.3 by default.
Signed-off-by: Jouni Malinen <j@w1.fi>
SSL_use_certificate_chain_file() was added in OpenSSL 1.1.0, so need to
maintain the old version using SSL_use_certificate_file() for backwards
compatibility.
Fixes: 658c39809b ("OpenSSL: Load chain certificates from client_cert file")
Signed-off-by: Jouni Malinen <j@w1.fi>
In addition, add even more workarounds for cfg80211 regulatory state
clearing since this test case seems to be the most likely one to fail
due to country=98 issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a regression test case for FT-over-DS that got broken on
mac80211-based drivers when the extra key reinstallation checks were
added.
Signed-off-by: Jouni Malinen <j@w1.fi>
FT-over-the-DS has a special case where the STA entry (and as such, the
TK) has not yet been configured to the driver depending on which driver
interface is used. For that case, allow add-STA operation to be used
(instead of set-STA). This is needed to allow mac80211-based drivers to
accept the STA parameter configuration. Since this is after a new
FT-over-DS exchange, a new TK has been derived after the last STA entry
was added to the driver, so key reinstallation is not a concern for this
case.
Fixes: 0e3bd7ac68 ("hostapd: Avoid key reinstallation in FT handshake")
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no point in going through FT authentication if the next step
would have to use association exchange which will be rejected by the AP
for FT, so only allow FT-over-air if previous BSSID is set, i.e., if
reassociation can be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_ft_oom seemed to depend on undesired wpa_supplicant behavior of
trying to do FT protocol even without being ready for reassociation.
This is going to be fixed in wpa_supplicant which would make this test
case fail, so split it into separate test cases for each failure item to
be able to avoid incorrect test failures.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous roam() and roam_over_ds() checks would have ignored failing
association rejection if a consecutive attempt to connect succeeds
within the initial time limit. This can miss incorrect behavior, so
check explicitly for association rejection.
Signed-off-by: Jouni Malinen <j@w1.fi>
