This allows a single BSS/SSID to be used for both data connection and
OSU. In wpa_supplicant configuration, the current proto=OSEN
key_mgmt=OSEN combination is now allowing both the old separate OSEN
BSS/IE and the new RSN-OSEN to be used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows a single BSS/SSID to be used for both data connection and
OSU. Instead of hostapd configuration osen=1, wpa_key_mgmt=OSEN (or more
likely, wpa_key_mgmt=WPA-EAP OSEN) is used to enable this new option.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Before calling HW macsec driver API, be_to_host16() should be used to
reverse the SCI port byte order. This was broken as part of the mka API
changes.
Fixes: 8ebfc7c2ba ("mka: Pass full structures down to macsec drivers' transmit SC ops")
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Run through the hunting-and-pecking loop 40 times to mask the time
necessary to find PWE. The odds of PWE not being found in 40 loops is
roughly 1 in 1 trillion.
Signed-off-by: Dan Harkins <dharkins@lounge.org>
Aborty processing if ID exchange processing is entered twice
unexpectedly. This avoids memory leaks in the function.
Signed-off-by: Jouni Malinen <j@w1.fi>
These changes add support for salted password databases to EAP-pwd per
RFC 8146. This commits introduces the framework for enabling this and
the actual salting mechanisms are introduced in the following commits.
Signed-off-by: Dan Harkins <dharkins@lounge.org>
There is no need to do this during the ID exchange, so move PWE
deriation into the following commit exchange in preparation for adding
support for salted passwords.
Signed-off-by: Dan Harkins <dharkins@lounge.org>
These changes add support for salted password databases to EAP-pwd per
RFC 8146. This commits introduces the framework for enabling this and
the salting mechanisms based on SHA-1, SHA256, and SHA512 hash
algorithms.
Signed-off-by: Dan Harkins <dharkins@lounge.org>
This commit adds a new vendor command attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_GTX in
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION to enable/disable green
Tx power saving feature.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
PMKSA caching with FT is not fully functional, so disable the case for
now, so that wpa_supplicant does not end up trying to connect with a
PMKSA cache entry from another AKM. FT-EAP was already modified long
time ago to not add PMKSA cache entries itself.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Move enum fst_reason to be a top level type, since it is used as
argument in the function fst_reason_name() and having it as nested
type caused a compile error when fst_ctrl_aux.h was included from
a C++ source file.
Signed-off-by: Lior David <liord@codeaurora.org>
This extends the SAE implementation in both infrastructure and mesh BSS
cases to allow an optional Password Identifier to be used. This uses the
mechanism added in P802.11REVmd/D1.0. The Password Identifier is
configured in a wpa_supplicant network profile as a new string parameter
sae_password_id. In hostapd configuration, the existing sae_password
parameter has been extended to allow the password identifier (and also a
peer MAC address) to be set. In addition, multiple sae_password entries
can now be provided to hostapd to allow multiple per-peer and
per-identifier passwords to be set.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The use of hostapd code for a mesh interface did not register
hapd->msg_ctx. This needs to be done similarly to the existing cases in
wpa_supplicant AP and IBSS mode uses so that wpa_msg() calls from the
hostapd/AP code get delivered properly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add NAN attributes to communicate IPv6 address, port, and protocol
between wifihal and host driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The n argument to this function is number of bits, not bytes, to shift.
As such, need to use mp_rshb() instead of mp_rshd(). This fixes EAP-pwd
with P-521 curve.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If no BSS entry can be found when processing association rejected event
from the driver for the special OWE case of unsupported
finite-cyclic-group, process the event as a connection failure instead
of just skipping the the OWE retry with another DH group.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, hostapd CHAN_SWITCH command did not effect VHT configuration
for the following:
When VHT is currently disabled (ieee80211ac=0),
1. hostapd_cli -p /var/run/hostapd chan_switch 10 5180 \
sec_channel_offset=1 center_freq1=5190 bandwidth=40 ht
====> Comes up in HT40
2. hostapd_cli -p /var/run/hostapd chan_switch 10 5765 \
sec_channel_offset=-1 center_freq1=5775 bandwidth=40 vht
====> Comes up in HT40
3. hostapd_cli -p /var/run/hostapd chan_switch 10 5200 center_freq1=5200 \
bandwidth=20 vht
====> Comes up in HT20
When VHT is currently enabled (ieee80211ac=1),
1. hostapd_cli -p /var/run/hostapd chan_switch 10 5180 \
sec_channel_offset=1 center_freq1=5190 bandwidth=40 ht
====> Comes up in VHT40
2. hostapd_cli -p /var/run/hostapd chan_switch 10 5200 center_freq1=5200 \
bandwidth=20 ht
====> Comes up in VHT20
This is since VHT config from chan_switch is processed only for
bandwidths 80 and above (80P80, 160) and for VHT20, VHT40 cases, only
NLA chan type and chan width are updated.
There is no NL attribute for determining if it is HT or VHT for
bandwidths 20 & 40 and currently they are updated as HT20, HT40 (+ or -
depending on offset). Same is notified back via
NL80211_CMD_CH_SWITCH_NOTIFY.
Instead of adding new NL attribute for tracking HT/VHT enabled config,
we are adding new hostapd VHT config parameter to save the chan_switch
config and use only for chan_switch case of VHT20 and VHT40.
Tested with all combinations of chan_switch (noHT->20->40->80->) HT/VHT
and confirmed to be working.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
On an assoc_reject from the BSS with the status=77, a connection attempt
with the next supported group happens. The BSS considered here is from
current_bss which may be NULL at this point of time with SME-in-driver
case. Address this by getting the BSS from the bssid obtained in
association reject indication and skip the step if no BSS entry can be
found.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When the channel time is zero the interference factor calculation falls
under divide by zero operation which results in invalid (NaN =
not-a-number) interference factor value. This leads to wrong ideal
channel selection in ACS during the scenario described below.
Scenario:
In VHT80 mode, the channel 36 (first channel) gets the channel time as
zero which causes the interfactor factor to be an invalid number (NaN).
Any operations (like addition, mulitplication, divide, etc.) with NaN
value results in a NaN value, so that average factor for the primary
channel 36 got the invalid value (NaN). Since channel 36 is the first
channel, ideal factor is assigned as NaN in the first iteration. The
following iteration condition check (factor < ideal_factor) with a NaN
value fail for all other primary channels. This results in channel 36
being chosen as the ideal channel in ACS which holds a NaN value.
Logs:
ACS: Survey analysis for channel 36 (5180 MHz)
ACS: 1: min_nf=-103 interference_factor=nan nf=0 time=0 busy=0 rx=0
ACS: 2: min_nf=-103 interference_factor=0.615385 nf=-102 time=13 busy=8 rx=0
ACS: 3: min_nf=-103 interference_factor=2.45455 nf=0 time=22 busy=16 rx=0
ACS: 4: min_nf=-103 interference_factor=0.785714 nf=-103 time=42 busy=33 rx=0
ACS: 5: min_nf=-103 interference_factor=nan nf=0 time=0 busy=0 rx=0
ACS: * interference factor average: nan
...
ACS: * channel 36: total interference = nan
..
ACS: * channel 149: total interference = 5.93174e-21
..
ACS: Ideal channel is 36 (5180 MHz) with total interference factor of nan
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Over time a number of style issues have crept into qca-vendor.h,
so fix most of them. There are some identifiers and comments which
exceed 80 columns, but these are left as-is for readability.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This can be used to determine which mechanism to use for configuring
country code from trusted sources.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure Tx
beamformee in the driver. This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Flush the PMKSA upon receiving association reject event without timeout
in the event data in SME-in-driver case to avoid trying to use the old
PMKSA entry in subsequent connection attempts. Do not flush PMKSA if
association reject is received with timeout as it is generated
internally from the driver without reaching the AP. This is similar to
the SME-in-wpa_supplicant case that was already addressed within
sme_event_assoc_reject().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The first two parameters to readlink() are marked restricted and at
least gcc 8.2 warns about used the same pointer for then, so avoid this
by using separate buffers for the pathname and response buffer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an explicit comment noting a previously undocumented fallthrough to
not trigger an implicit-fallthrough warning.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reword the comments to make gcc 8.1 recognize these as designed cases
and not trigger implicit-fallthrough warnings.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Couple of "invalid value" tests started to fail now that mac80211_hwsim
actually accepts power save configuration. Fix these by running the same
command for more code coverage, but in a way that ignores the result of
the operation (succeeds with older kernel versions and fails with
newer).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
SME ft_used flag is sometimes not cleared on disassoc. For example,
after initial FT connection, ft_used is set while ft_ies stays NULL.
Later on, upon disassoc, sme_update_ft_ies() is not invoked and ft_used
is not cleared. Fix this by invoking sme_update_ft_ies() also in case
ft_used is set.
This is needed to fix an issue with drivers that use nl80211 Connect API
with FT and expect to the NL80211_AUTHTYPE_OPEN specified in the Connect
command for the initial mobility domain association.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
This allows user to get channel switch indication in station mode even
if wpa_supplicant is built without CONFIG_AP=y.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Implement tls_connection_get_eap_fast_key() using cryptographic
primitives as wolfSSL implements different spec.
Signed-off-by: Sean Parkinson <sean@wolfssl.com>
