DPP tech spec changed the contents of these frames by replacing the
public key hash attributes with a Transaction ID attribute that gets
copied from the request to the response to identify the transaction in a
simpler manner.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, CONFIG_WNM enabled build that supports WNM for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode WNM is required and there is no need for AP mode WNM.
Add support to differentiate between station mode WNM and AP mode
WNM in wpa_supplicant builds by adding CONFIG_WNM_AP that should be
used when AP mode WNM support is required in addition to station mode
WNM. This allows binary size to be reduced for builds that require
only the station side WNM functionality.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add OCE IE in Beacon, Probe Response, and (Re)Association Response
frames if OCE is enabled in the configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In case of incorrect HT40 configuration as part of an attempt to create
a 80 MHz AP, iface->conf->vht_oper_centr_freq_seg0_idx and
iface->conf->vht_oper_centr_freq_seg1_idx are zero'ed, but
iface->conf->vht_oper_chwidth remains VHT_CHANWIDTH_80MHZ. This causes
the logic in dfs_get_start_chan_idx to fail.
Fix this by setting iface->conf->vht_oper_chwidth to
VHT_CHANWIDTH_USE_HT when zero'ing the center frequency parameters.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
dpp.h file requires openssl in order to compile, which breaks
compilation on systems without it.
Move DPP_OUI_TYPE to ieee802_11_defs.h and don't include dpp.h when
not really needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
hostapd did not add a new PMKSA cache entry when FILS shared key
authentication was used, i.e., only the initial full authentication
resulted in a PMKSA cache entry being created. Derive the PMKID for the
ERP case as well and add a PMKSA cache entry if the ERP exchange
succeeds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The EAP message included in FILS Wrapped Data from the non-AP STA to the
AP is EAP-Initiate/Re-auth.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the hostapd control interface to support the
DPP_BOOTSTRAP_INFO command that was recently added for wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The default value for GTK rekeying period was previously hardcoded to
600 seconds for all cases. Leave that short value only for TKIP as group
cipher while moving to the IEEE 802.11 default value of 86400 seconds
(once-per-day) for CCMP/GCMP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This updates the previously copied implementation to be up-to-date with
the more recent wpa_supplicant changes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow hostapd to initiate and respond with PKEX bootstrapping similarly
to how this was implemented in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend hostapd configuration to include parameters needed for the DPP
AKM: dpp_connector, dpp_netaccesskey, dpp_netaccesskey_expiry,
dpp_csign, dpp_csign_expiry.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external programs to generate and add PMKSA cache entries
into hostapd. The main use for this is to run external DPP processing
(network introduction) and testing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds DPP bootstrapping, authentication, and configuration into
hostapd similarly to how the design was integrated in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd processes a received 20/40 BSS Coexistence management frame, but
if no separate callbacks are registered for handling Public Action
frames it eventually sends a reply with MSB of category code set to 1
thinking that the received frame is an invalid frame. This could happen
based on whether hostapd was built and enabled with functionality using
the callback functions.
Fix this by explicitly returning 1 from the function when the 20/40 BSS
Coexistence Management frame is processed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new acs_exclude_dfs=1 parameter can be used to request hostapd to
exclude all DFS channels from ACS consideration. This is mainly of use
for cases where the driver supports DFS channels, but for some reason a
non-DFS channel is desired when using automatic channel selection.
Previously, the chanlist parameter could have been used for this, but
that required listing all the acceptable channels. The new parameter
allows this to be done without such a list.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is to comply with uniform spreading requirement for ETSI domain
(section 4.7.2.7 in EN 301 893 - V1.8.1). ETSI uniform spreading
requires equal probability for the usable channels. The previous channel
selection logic after a radar detection did not fully comply with the
uniform spreading requirement for the domain by ignoring DFS channels.
Consider DFS channels also during channel selection when the current DFS
domain is ETSI.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Derive PMK-R0 and the relevant key names when using FILS authentication
for initial FT mobility domain association.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends fils_pmk_to_ptk() to allow FILS-FT to be derived. The
callers do not yet use that capability; i.e., actual use will be added
in separate commits.
Signed-off-by: Jouni Malinen <j@w1.fi>
The conditional gSTA and gAP (DH public keys) were not previously
included in Key-Auth derivation, but they are needed for the PFS case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Enable use of FT RRB without configuring each other AP locally. Instead,
broadcast messages are exchanged to discover APs within the local
network.
When an R0KH or R1KH is discovered, it is cached for one day.
When a station uses an invalid or offline r0kh_id, requests are always
broadcast. In order to avoid this, if r0kh does not reply, a temporary
blacklist entry is added to r0kh_list.
To avoid blocking a valid r0kh when a non-existing pmk_r0_name is
requested, r0kh is required to always reply using a NAK. Resend requests
a few times to ensure blacklisting does not happen due to small packet
loss.
To free newly created stations later, the r*kh_list start pointer in
conf needs to be updateable from wpa_auth_ft.c, where only wconf is
accessed.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This adds a counter and adds sequence numbering to FT RRB packets. The
sequence number is checked against r0kh/r1kh sequence number cache.
Special attention is needed in case the remote AP reboots and thus loses
its state. I prefer it to recover automatically even without synchronized
clocks. Therefore an identifier called dom is generated randomly along the
initial sequence number. If the dom transmitted does not match or the
sequence number is not in the range currently expected, the sender is asked
for a fresh confirmation of its currently used sequence numbers. The packet
that triggered this is cached and processed again later.
Additionally, in order to ensure freshness, the remote AP includes an
timestamp with its messages. It is then verified that the received
messages are indeed fresh by comparing it to the older timestamps
received and the time elapsed since then. Therefore FT_RRB_TIMESTAMP is
no longer needed.
This assigns new OUI 00:13:74 vendor-specific subtype 0x0001 subtypes:
4 (SEQ_REQ) and 5 (SEQ_RESP).
This breaks backward compatibility, i.e., hostapd needs to be updated
on all APs at the same time to allow FT to remain functional.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Convert FT RRB into a new TLV based format. Use AES-SIV as AEAD cipher
to protect the messages.
This needs at least 32 byte long keys. These can be provided either
by a config file change or letting a KDF derive the 32 byte key used
from the 16 byte key given.
This breaks backward compatibility, i.e., hostapd needs to be updated on
all APs at the same time to allow FT to remain functional.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Replace the previously used extension of IEEE 802.11 managed Ethertype
89-0d (originally added for Remote Request/Response in IEEE 802.11r)
with Ethertype 88-b7 (OUI Extended EtherType) for FT inter-AP
communication. The new design uses a more properly assigned identifier
for the messages.
This assigns the OUI 00:13:74 vendor-specific subtype 0x0001 for the new
hostapd AP-to-AP communication purposes. Subtypes 1 (PULL), 2 (RESP),
and 3 (PUSH) are also assigned in this commit for the R0KH-R1KH
protocol.
This breaks backward compatibility, i.e., hostapd needs to be updated on
all APs at the same time to allow FT to remain functional.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Commit 941caed980 ('MBO: Add MBO
ANQP-element processing on AP') changed the design by using the
rx_anqp_vendor_specific() function to process all ANQP vendor specific
elements. However, the caller for this was within ifdef CONFIG_HS20
block. Fix this by calling the function even in CONFIG_HS20=y is not
included in the build. This fixes CONFIG_MBO=y builds without
CONFIG_HS20=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
When starting AP in HT40 mode and both HT40+ and HT40- options are
specified in hostapd.conf, select a valid secondary channel for the AP
automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow this function to be called from outside ieee802_11.c and with the
final steps replaced through a callback function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This function does not need the frame header, so pass in only the IE
area to make it easier to share this for driver-based AP SME handling.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is used with partial AP SME in driver cases to enable FILS
association (AES-SIV) processing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to add more parameters without having to change the
callback function prototype.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
MDE was already added with RSNE, but FTE needed to be added to the FILS
Authentication frame for the FT initial mobility domain association
using FILS authentication case.
Signed-off-by: Jouni Malinen <j@w1.fi>
With AP-AP communication, when hapd0 sends a packet, hapd1 can receive
it immediately and send a response. But hapd0 will only read and process
the response after it has returned from the sending context, that is
entered eloop again. So one does not need to consider the RX function of
the reply to run for the request sending hapd before the send calling
function has returned.
Previously, with intra-process communication, the packet is not
scheduled through eloop. Thus the RX handler of the reply might be run
while the sending context of the original request has not returned.
This might become problematic, e.g., when deferring a management frame
processing until an RRB response is received and then have the request
restarted and finished before the original request handling has been
stopped.
I'm not aware of any concrete bug this is currently triggering but came
across it while thinking of FT RRB AP-AP sequence numbering.
I think the non-eloop scheduling approach might be error-prone and thus
propose to model it more closely to the way the message would be
received from a socket. Additionally, this ensures that the tests model
AP-AP communication more closely to real world.
Solution: queue these packets through eloop.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
With multiple interface like AP and station which is already
associated to some other AP, when we try to do channel switch
for the AP mode (different from the operation channel support of
station) and if the AP channel switch fails continously (including
the fallback channel switch), results in a crash due to NULL pointer
dereference. This is because hostapd_deinit_driver() assigns the
driver context (drv_priv) to NULL as we are not able to bring up
the interface with a new channel
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
This fixes the following compiler warning:
wpa_auth.c:4249:34: error: address of array 'a->conf.fils_cache_id'
will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds an option to configure hostapd to enable use of perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime configuration parameter fils_dh_group is used to enable this
by specifying which DH group to use. For example, fils_dh_group=19 would
allow FILS SK PFS to be used with a 256-bit random ECP group.
Signed-off-by: Jouni Malinen <j@w1.fi>
draft-harkins-owe-07.txt does not specify these parameters, so need to
pick something sensible to use for the experimental implementation. The
Suite B 128-bit level AKM 00-0F-AC:11 has reasonable parameters for the
DH group 19 case (i.e., SHA256 hash), so use it for now. This can be
updated if the OWE RFC becomes clearer on the appropriate parameters
(KEK/KCK/MIC length, PRF/KDF algorithm, and key-wrap algorithm).
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds AP side processing for OWE Diffie-Hellman Parameter element in
(Re)Association Request frame and adding it in (Re)Association Response
frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the GAS server to process MBO ANQP-elements and reply to a
query for the Cellular Data Connection Preference (if configured). The
new configuration parameter mbo_cell_data_conn_pref can be used to set
the value (0, 1, or 255) for the preference to indicate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
As FCC DFS requirement does not explicitly mention about the validity of
the (pre-)CAC when channel is switched, it is safe to assume that the
pre-CAC result will not be valid once the CAC completed channel is
switched or radar detection is not active on the (CAC completed) channel
within a time period which is allowed (10 seconds - channel switch time)
as per FCC DFS requirement.
Use the new driver event to allow the driver to notify expiry of the CAC
result on a channel. Move the DFS state of the channel to 'usable' when
processing pre-CAC expired event. This means any future operation on
that channel will require a new CAC to be completed. This event is
applicable only when DFS is not offloaded to the kernel driver.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
When DFS channel state is shared across multiple radios on the system it
is possible that a CAC completion event is propagated from other radio
to us. When in enabled state, do not proceed with setup completion upon
processing CAC completion event with devices where DFS is not offloaded,
when in state other than enabled make sure the configured DFS channel is
in available state before start the AP.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
This leads to cleaner code overall, and also reduces the size
of the hostapd and wpa_supplicant binaries (in hwsim test build
on x86_64) by about 2.5 and 3.5KiB respectively.
The mechanical conversions all over the code were done with
the following spatch:
@@
expression SIZE, SRC;
expression a;
@@
-a = os_malloc(SIZE);
+a = os_memdup(SRC, SIZE);
<...
if (!a) {...}
...>
-os_memcpy(a, SRC, SIZE);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was possible to hit a double-free on the l2_packet socket if
initialization of DHCP/NDISC snoop failed on a hostapd interface that
had previously had those enabled successfully. Fix this by clearing the
l2_packet pointers during deinit.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf parameter country3 can now be used to configure the
third octet of the Country String that was previously hardcoded to ' '
(= 0x20).
For example:
All environments of the current frequency band and country (default)
country3=0x20
Outdoor environment only
country3=0x4f
Indoor environment only
country3=0x49
Noncountry entity (country_code=XX)
country3=0x58
IEEE 802.11 standard Annex E table indication: 0x01 .. 0x1f
Annex E, Table E-4 (Global operating classes)
country3=0x04
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When getting the channel number from a frequency, all supported modes
should be checked rather than just the current mode. This is needed when
hostapd switches to a channel in different band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The __FAVOR_BSD macro was previously used in netinet/udp.h to select
between two different names of the variables in struct udphdr. Define
that to force the versions with the uh_ prefix. In addition, use the
same style consistently within fils_hlp.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new broadcast_deauth parameter can be used to disable sending of the
Deauthentication frame whenever AP is started or stopped. The default
behavior remains identical to the past behavior (broadcast_deauth=1).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 01e2231fdc ('hostapd: Skip some
configuration steps for mesh cases') removed some operations based on
hapd->iface->mconf being NULL. This was within #ifdef CONFIG_MESH, so it
should not impact hostapd, but it can impact AP mode with
wpa_supplicant. That does not sound intentional, so make these
conditional on hapd->conf->mesh being enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows PMKSA cache entries to be shared between all the BSSs
operated by the same hostapd process when those BSSs use the same FILS
Cache Identifier value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE 802.11ax HE changes to include HE IEs in Beacon and Probe Response
frames. These elements are using vendor specific forms for now since the
IEEE 802.11ax draft is not yet finalized and the element contents is
subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add IEEE 802.11ax definitions for config, IEEE structures, and
constants. These are still subject to change in the IEEE process.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Let mesh STA A be a STA which has config disable_ht=0 and disable_vht=1.
Let mesh STA B be a STA which has config disable_ht=0 and disable_vht=0.
The mesh STA A and B was connected.
Previously, the mesh STA A sent frame with VHT rate even though its VHT
was disabled. This commit fixes the issue by checking the local BSS VHT
configuration.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Let mesh STA A be a STA which has config disable_ht=1.
Let mesh STA B be a STA which has config disable_ht=0.
The mesh STA A and B was connected.
Previously, the mesh STA A sent frame with HT rate even though its HT
was disabled. This commit fixes the issue by checking the local BSS HT
configuration.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
While the FILS authentication cases were already using the proper PMK
length (48 octets instead of the old hardcoded 32 octet), the initial
association case had not yet been updated to cover the new FILS SHA384
AKM and ended up using only a 32-octet PMK. Fix that to use 48-octet PMK
when using FILS SHA384 AKM.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, any potential (even if very unlikely) local operation error
was ignored. Now these will result in aborting the negotiation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The url argument to ieee802_11_send_bss_trans_mgmt_request() was
hardcoded to NULL in the only caller, so this code cannot be reached.
wnm_send_bss_tm_req() construct the same frame with more generic
parameters, including option for including the URL, so
ieee802_11_send_bss_trans_mgmt_request() can be simplified.
Signed-off-by: Jouni Malinen <j@w1.fi>
The length of the WNM-Sleep element was not verified before using it.
This could result in reading the subfields in this element (total of
four octets) beyond the end of the buffer. Fix this by ignoring the
element if it is not long enough to contain all the subfields.
Signed-off-by: Jouni Malinen <j@w1.fi>
The struct wpa_stsl_negotiation seemed to have been for some kind of
tracking of state of PeerKey negotiations within hostapd. However,
nothing is actually adding any entries to wpa_auth->stsl_negotiations or
using this state. Since PeerKey does not look like something that would
be deployed in practice, there is no justification to spend time on
making this any more complete. Remove the dead code now instead of
trying to figure out what it might be used for.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the int medium_time variable to overflow, so use a
64-bit unsigned integer to get a large enough value for the
multiplication.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to maintain different return paths for STA being
completely not present and not authorized, so merge these into a single
case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This 16-bit field uses little endian encoding and it must be read with
WPA_GET_LE16() instead of assuming host byte order is little endian. In
addition, this could be misaligned, so using a u16 pointer here was not
appropriate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hapd->acl_cache and hapd->acl_queries were not reset back to NULL in
hostapd_acl_deinit() when cached results and pending ACL queries were
freed. This left stale pointers to freed memory in hapd. While this was
normally followed by freeing of the hapd data, it is possible to re-use
that hapd when disabling and re-enabling an interface. That sequence
could result in use of freed memory if done while there were cached
results or pending ACL operations with a RADIUS server (especially, if
that server did not reply).
Fix this by setting hapd->acl_queries to NULL when the pending entries
are freed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The "!wpabuf_resize(...) == 0" condition does not make any sense. It
happens to work, but this is really supposed to simple check with
wpabuf_resize() returns non-zero and "wpabuf_resize(...)" is the
cleanest way of doing so.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the OSU Providers configuration was invalid (included osu_server_uri
but not osu_method_list), it was possible for the GAS response
generation to hit a NULL dereference. Fix this by checking for the
invalid configuration before trying to fill in the OSU methods.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It can happen if the station is unreachable or sleeping longer than
the actual total GTK rekey timeout. To fix the latter case
wpa_group_update_count may be increased.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
wpa_group_update_count and wpa_pairwise_update_count can now be used to
set the GTK and PTK rekey retry limits (dot11RSNAConfigGroupUpdateCount
and dot11RSNAConfigPairwiseUpdateCount). Defaults set to current
hardcoded value (4).
Some stations may suffer from frequent deauthentications due to GTK
rekey failures: EAPOL 1/2 frame is not answered during the total timeout
period of currently ~3.5 seconds. For example, a Galaxy S6 with Android
6.0.1 appears to go into power save mode for up to 5 seconds. Increasing
wpa_group_update_count to 6 fixed this issue.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
Some channels fail to be set, when falling back to 20 MHz, due to
remaining VHT info of center freq. As we are going to 20 MHz, reset the
VHT center frequency segment information as well.
Signed-off-by: Eduardo Abinader <eduardoabinader@gmail.com>
Commit 91d91abf6f ('FILS: DHCP relay for
HLP requests') added steps that are conditional on sta->fils_hlp_resp
being non-NULL. One of these cases within send_assoc_resp() was properly
protected from sta == NULL error case (that is now possible after a
recent DMG change), but the first one was not. A DMG error case in a
CONFIG_FILS=y build could have hit a NULL pointer dereference here. Fix
this by verifying sta != NULL more consistently.
Signed-off-by: Jouni Malinen <j@w1.fi>
P802.11i/D3.0 described the Key Length as having value 16 for the group
key handshake. However, this was changed to 0 in the published IEEE Std
802.11i-2004 amendment (and still remains 0 in the current standard IEEE
Std 802.11-2016). We need to maintain the non-zero value for WPA (v1)
cases, but the RSN case can be changed to 0 to be closer to the current
standard.
Signed-off-by: Jouni Malinen <j@w1.fi>
While the IEEE Std 802.11-2016 is still indicating that GNonce would be
exchanged in EAPOL-Key messages (see, e.g., Figure 12-52 showing the
Send EAPOL-Key operation in the REKEYNEGOTIATING state or the sample
group key handshake in Figure 12-47), there are also examples of
describing this field as having value zero (e.g., 12.7.7.2 Group key
handshake message 1).
GNonce is used only with the Authenticator and the Supplicant does not
have any use for it, so it is better not to expose that internal value.
Hardcode the Key Nonce field to 0 in EAPOL-Key group message 1/2.
Signed-off-by: Jouni Malinen <j@w1.fi>
sm->Pair needs to be initialized to TRUE since unicast cipher is
supported and this is an ESS. However, the normal place for setting this
(WPA_PTK::INITIALIZE) is skipped with using FT protocol or FILS
authentication, so need to do that separately when forcing PTKINITDONE.
Signed-off-by: Jouni Malinen <j@w1.fi>
The local custom version of allocating and initializing struct
hostapd_data within wpa_supplicant_mesh_init() is problematic. This has
already missed couple of initialization steps that are required. Instead
of trying to remember to keep this up to date, use
hostapd_alloc_bss_data() so that there is only one place for this
initialization.
This is fixing a recent issue where FILS HLP started using
hapd->dhcp_server and expected that to be initialized to -1. For the
mesh case, that did not happen and when removing the interface, the FILS
HLP implementation ended up unregistering eloop socket for
hapd->dhcp_server (= 0). This could result in missing socket callbacks
for an arbitrary socket.
Signed-off-by: Jouni Malinen <j@w1.fi>
The hostapd processing of the AES-SIV AAD was incorrect. The design for
the AAD changed between P802.11ai/D7.0 and D8.0 from a single vector
with concatenated data to separate vectors. The change in the
implementation had missed the change in the aes_siv_decrypt() call for
the num_elem parameter. This happened to work with the mac80211
implementation due to a similar error there.
Fix this by using the correct numbers of vectors in the SIV AAD so that
all the vectors get checked. The last vector was also 14 octets too long
due to incorrect starting pointer, so fix that as well. The changes here
are not backwards compatible, i.e., a similar fix in the Linux mac80211
is needed to make things interoperate again.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new dhcp_server configuration parameter can now be used to configure
hostapd to act as a DHCP relay for DHCPDISCOVER messages received as
FILS HLP requests. The dhcp_rapid_commit_proxy=1 parameter can be used
to configure hostapd to convert 4 message DHCP exchange into a 2 message
exchange in case the DHCP server does not support DHCP rapid commit
option.
The fils_hlp_wait_time parameter can be used to set the time hostapd
waits for an HLP response. This matches the dot11HLPWaitTime in IEEE Std
802.11ai-2016.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is independent functionality from the core IEEE 802.11 management
handling and will increase significantly in size, so it is cleaner to
maintain this in a separate source code file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not depend on undefined behavior with pointer arithmetic when
checking whether there is sufficient room for an option.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These can be reused for other purposes than just the DHCP snoofing for
Proxy ARP. In addition, use more complete definition of the parameters
based on the current IANA registry.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
With device_ap_sme disabled, ACL was checked upon authentication
request. In 802.11ad there is no authentication phase so need to check
ACL upon association.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Previously, the temporary STA session timeout was set to 5 seconds. If
gas_comeback_delay is configured to be longer than 5 seconds, GAS
Comeback Response frame can't include queried information as all pending
data has already been cleared due to session timeout. This commit
resolves the issue by setting session timeout to be larger than
gas_comeback_delay.
Signed-off-by: Daniel Kim <kimdan@qca.qualcomm.com>
Instead of copying the struct wpa_auth_callbacks, just keep a pointer to
it, keep the context pointer separate, and let the user just provide a
static const structure. This reduces the attack surface of heap
overwrites, since the function pointers move elsewhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds parsing of received FILS HLP requests from (Re)Association
Request frames. The reassembled requests are verified to be in valid
format and are printed in debug output. However, actual processing or
forwarding of the packets is not yet implemented, i.e., the vendor
specific frame filtering logic is for now practically dropping all HLP
requests.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These commnds are mesh version of PMKSA_GET/ADD commands. So the usage
and security risk is similar to them. Refer to
commit 3459381dd2 ('External persistent
storage for PMKSA cache entries') also.
The MESH_PMKSA_GET command requires peer MAC address or "any" as an
argument and outputs appropriate stored PMKSA cache. And the
MESH_PMKSA_ADD command receives an output of MESH_PMKSA_GET and re-store
the PMKSA cache into wpa_supplicant. By using re-stored PMKSA cache,
wpa_supplicant can skip commit message creation which can use
significant CPU resources.
The output of the MESH_PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <expiration in seconds>
The example of MESH_PMKSA_ADD command is this.
MESH_PMKSA_ADD 02:00:00:00:03:00 231dc1c9fa2eed0354ea49e8ff2cc2dc cb0f6c9cab358a8146488566ca155421ab4f3ea4a6de2120050c149b797018fe 42930
MESH_PMKSA_ADD 02:00:00:00:04:00 d7e595916611640d3e4e8eac02909c3c eb414a33c74831275f25c2357b3c12e3d8bd2f2aab6cf781d6ade706be71321a 43180
This functionality is disabled by default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Relational operators (==) have higher precedence than the ternary
conditional in C. The last_subtype check for association/reassociation
was broken due to incorrect assumption about the precedence. Fix this by
adding parenthesis around the ternary conditional.
The previous implementation worked for Association Request frames by
accident since WLAN_FC_STYPE_ASSOC_REQ happens to have value 0 and when
the last receive frame was an Association Request frame, the
sta->last_subtype == reassoc check was true and non-zero
WLAN_FC_STYPE_REASSOC_REQ was interpreted as true. However, this was
broken for Reassociation Request frame. reassoc == 1 in that case could
have matched received Association Response frame (subtype == 1), but
those are not received in AP mode and as such, this did not break other
behavior apart from not being able to drop duplicated Reassociation
Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds helper functions for deriving PMK and PMKID from ERP exchange
in FILS shared key authentication as defined in IEEE Std 802.11ai-2016,
12.12.2.5.2 (PMKSA key derivation with FILS authentication). These
functions is used to fix PMK and PMKID derivation which were previously
using the rMSK directly as PMK instead of following the FILS protocol to
derive PMK with HMAC from nonces and rMSK.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Check the action TX status callback contents more thoroughly and report
the BEACON-REQ-TX-STATUS event only if the Measurement Type indicates
beacon report.
Signed-off-by: Jouni Malinen <j@w1.fi>
Authentication and Deauthentication frames are not used in DMG/IEEE
802.11ad networks. For DMG/IEEE 802.11ad the following was implemented:
Upon receiving association request, allocate the sta object and
initialize it as if authentication took place. Upon receiving
disassociation, deallocate the sta object.
ap_sta_disassociate/ap_sta_deauthenticate/ap_sta_disconnect all use
disassociation instead of deauthentication. In driver_nl80211,
i802_sta_deauth() is routed to i802_sta_disassoc().
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Supported Rates element is not present in DMG/IEEE 802.11ad frames. Make
copy_supp_rates() immediately return with success if hardware mode is
IEEE 802.11ad.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
The new hostapd control interface event "BEACON-RESP-RX <STA address>
<dialog token> <report mode> <beacon report>" is now used to report
received beacon reports as a reponse to the REQ_BEACON operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new BEACON-REQ-TX-STATUS control interface event is now used to
report whether a beacon request (from REQ_BEACON command) was delivered
successfully. This event has the following parameters: <STA address>
<dialog token> <ack=0/1>.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new control interface command "REQ_BEACON <STA addr>
[req_mode=<mode>] <beacon request>" can now be used to request hostapd
to transmit a measurement request to request a beacon report from an
associated STA. This command returns the assigned dialog token (1-255)
or FAIL on failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
The loop to add hash values was supposed to be limited to at most 10000
values, but the count variable was not being decremented in the loop.
Fix this by decrementing counting for each iteration. This fixes
ANQP-element format in the unlikely case of there being more than 10000
configuration realms.
Signed-off-by: Jouni Malinen <j@w1.fi>
The actual BSS configuration parameter can be updated with the SET
control interface command, so there is no need to maintain a separate
per-BSS parameter and a separate control interface handling for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, the hostapd ft_over_ds parameter was used to only advertise
whether FT-over-DS is enabled in MDE and leave it to the stations to
follow that advertisement. This commit extends this to explicitly reject
(silently drop) FT Action frames if a station does not follow the
advertised capabilities.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, this was noted in error log, but the invalid value was
stored in the configuration without rejecting it.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible to try to do driver operations before the driver
interface had been initialized when processing a SIGHUP signal. This
would result in NULL pointer dereference. Fix this by skipping the steps
when SIGHUP is issued before the interface is enabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function is already checking the fname argument against NULL, so
use that check on its own instead of duplicating the check in the only
caller.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is apparently possible for the NL80211_CMD_UNEXPECTED_4ADDR_FRAME
event to be delivered to hostapd before the NL80211_CMD_FRAME_TX_STATUS
event for (Re)Association Response frame. This resulted in the 4-address
WDS mode not getting enabled for a STA. This could occur in particular
when operating under heavy load and the STA is reconnecting to the same
AP in a sequence where Deauthentication frame is followed immediately by
Authentication frame and the driver event processing gets delayed due to
removal of the previous netdev taking time in the middle of this
sequence.
Fix this by recording a pending item for 4-address WDS enabling if the
NL80211_CMD_UNEXPECTED_4ADDR_FRAME event would have been dropped due to
incompleted association and then process this pending item if the TX
status for the (Re)Association Response frame is received and it shows
that the frame was acknowledged.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd configuration parameter fils_realm=<realm> can now be
used to configure one or more FILS realms to advertise for ERP domains
when using FILS. This replaces the use of erp_domain=<domain> parameter
for the FILS use case.
Signed-off-by: Jouni Malinen <j@w1.fi>
P802.11ai/D7.0 changed from CRC32 to SHA256 as the hash algorithm for
the FILS realm name. Update the implementation to match that change.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the secondary channel was not found at all, no debug print was shown
to indicate that the channel was rejected due to that problem. Print a
clearer message indicating which channel was behind the reason to reject
channel configuration as unsuitable for AP mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd didn't send "TERMINATING" event when stopped by
SIGTERM. Android handles this event to stop monitor thread.
This commit adds "TERMINATING" event same as with wpa_supplicant.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
Previously, os_sleep() was used to block the hostapd (or wpa_supplicant
AP/P2P GO mode) processing between sending out EAP-Failure and
disconnecting the STA. This is not ideal for couple of reasons: it
blocks all other parallel operations in the process and it leaves a
window during which the station might deauthenticate and the AP would
have no option for reacting to that before forcing out its own
Deauthentication frame which could go out after the STA has already
started new connection attempt.
Improve this design by scheduling an eloop timeout of 10 ms instead of
the os_sleep() call and perform the delayed operations from the eloop
callback function. This eloop timeout is cancelled if the STA
disconnects or initiates a new connection attempt before the 10 ms time
is reached. This gets rid of the confusing extra Deauthentication frame
in cases where the STA reacts to EAP-Failure by an immediate
deauthentication.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds support for nl80211 NL80211_CMD_SET_MULTICAST_TO_UNICAST
command.
By setting the new hostapd configuration option multicast_to_unicast=1,
hostapd configures this AP to perform multicast to unicast conversion.
When enabled, all multicast packets with ethertype ARP, IPv4, or IPv6
(possibly within an 802.1Q header) will be sent out to each station once
with the destination (multicast) MAC address replaced by the station's
MAC address. Note that this may break certain expectations of the
receiver, e.g., the ability to drop unicast IP packets encapsulated in
multicast L2 frames, or the ability to not send destination unreachable
messages in such cases.
This also does not implement Directed Multicast Service (DMS).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
We should unconditionally remove inactivity timers for wired network
cases. This commit checks for this after a new station association:
hapd->iface->drv_flags & WPA_DRIVER_FLAGS_WIRED
and then cancels the timeout and does not register a new one.
It prints out a debug message like this:
1476740180.276286: IEEE 802.1X: 00:02:00:00:00:07 CTRL_DIR entering
state FORCE_BOTH
1476740180.276295: hostapd_new_assoc_sta: canceled wired ap_handle_timer
timeout for 00:02:00:00:00:07
This was tested on a debian jessie amd64 system with a configured 120
second inactivity timer and the session did not timeout.
Signed-off-by: Sam Tannous <stannous@cumulusnetworks.com>
Data connection was lost if a station reassociated without the STA entry
being cleaned up on the AP side. Fix this by moving reconfiguration of
the STA WDS parameters in association response callback to happen only
after the STA flags have been updated to associated stated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This fixes a regression from commit
bb598c3bdd ('AP: Add support for full
station state'). That commit added code to remove and re-add the kernel
STA entry when processing Authentication frames with a driver that
advertises support for full AP client state. That resulted in bypassing
PMF protections for unprotected Authentication frames with such drivers
since the TK was lost in this operation.
It is simplest to skip the STA entry clearing in this type of case
completely to leave the TK in place and to process the new
authentication exchange otherwise normally. This matches the behavior
used with the drivers that do not implement full AP client state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11-2012, 12.4.2 states that if an MDE is present in an
(Re)Association Request frame but the RSNE uses a non-FT AKM suite, the
AP shall reject the association using status code 43 ("Invalid AKMP").
wpa_validate_wpa_ie() now explicitly checks for this condition to meet
this requirement instead of simply ignoring the MDE based on non-FT AKM.
Signed-off-by: Will Glynn <will@willglynn.com>
Allow configuration of Beacon frame TX rate from hostapd.conf with
"beacon_rate=xx" option. The following format is used to set
legacy/HT/VHT beacon rates:
Legacy (CCK/OFDM rates):
beacon_rate=<legacy rate in 100 kbps>
HT:
beacon_rate=ht:<HT MCS>
VHT:
beacon_rate=vht:<VHT MCS>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the anqp_elem configuration parameter support for new Info
IDs (270 (TDLS Capability) was previously missed from the list of
defined values, 280 has already been assigned in REVmc/D8.0; 281..299
are yet to be assigned). No additional source code changes are needed to
allow hostapd to advertise support for these if the ANQP-element value
is set with the anqp_elem parameter.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, CONFIG_IEEE80211R enabled build that supports FT for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode FT is required and there is no need for AP mode FT.
Add support to differentiate between station mode FT and AP mode FT in
wpa_supplicant builds by adding CONFIG_IEEE80211R_AP that should be used
when AP mode FT support is required in addition to station mode FT. This
allows binary size to be reduced for builds that require only the
station side FT functionality.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The Channel Center Frequency Segment subfields use the channel index
instead of frequency in MHz.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
The return value from this function may be used in an outgoing message,
so use a valid status code instead of -1.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add a configuration option in hostapd.conf and in neighbor report that
sets an AP as stationary. To enable this option on the current AP set
the config option stationary_ap to 1. To set a neighbor entry to be
marked as stationary add the word stat to the SET_NEIGHBOR command. This
option tells hostapd to send LCI data even if it is older than requested
by max age subelement in RRM request.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
It is possible that a LCI or location civic configuration buffer
is valid but contains no data. In such a case do not add the LCI
and location civic information to the entry in the neighbor
data base.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This has already been done for WEP, but there's same constraint for not
allowing VTH rates in case of TKIP.
Signed-off-by: Filip Matusiak <filip.matusiak@tieto.com>
Add signal level information to the station tracking information. Also
make it available via the "TRACK_STA_LIST" control command.
Signed-off-by: Kevin Mahoney <k.mahoney@cablelabs.com>
This makes wpa_remove_ptk() call to wpa_auth_set_key() more consistent
with all the other calls that verify the return value to keep static
analyzers happier.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements processing of FILS Authentication frame for FILS shared
key authentication with ERP and PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
ieee802_1x_encapsulate_radius() and ieee802_1x_alloc_eapol_sm() need to
be called from FILS processing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This changes 4-way handshake authenticator processing to decrypt the
EAPOL-Key frames using an AEAD cipher (AES-SIV with FILS AKMs) before
processing the Key Data field. This replaces Key MIC validation for the
cases where AEAD cipher is used. This needs to move the EAPOL-Key msg
2/4 RSN element processing to happen only after the PTK has been derived
and validated. That is done for all AKMs to avoid extra complexity with
having to maintain two code paths for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Suite B 192-bit addition from IEEE Std 802.11ac-2013 replaced the
previous fixed length Key MIC field with a variable length field. That
change was addressed with an addition of a new struct defined for the
second MIC length. This is not really scalable and with FILS coming up
with a zero-length MIC case for AEAD, a more thorough change to support
variable length MIC is needed.
Remove the Key MIC and Key Data Length fields from the struct
wpa_eapol_key and find their location based on the MIC length
information (which is determined by the AKMP). This change allows the
separate struct wpa_eapol_key_192 to be removed since struct
wpa_eapol_key will now include only the fixed length fields that are
shared with all EAPOL-Key cases in IEEE Std 802.11.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Calculate the hashed realm from hostapd erp_domain configuration
parameter and add this to the FILS Indication element when ERP is
enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If FILS is enabled, indicate that in Beacon, Probe Response, and
(Re)Association Response frames in the Extended Capabilities element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds CONFIG_FILS=y build configuration option and new key
management options for FILS authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Station should be able to connect initially without ft_pmk_cache filled,
so the target AP has the PSK available and thus the same information as
the origin AP. Therefore neither caching nor communication between the
APs with respect to PMK-R0 or PMK-R1 or VLANs is required if the target
AP derives the required PMKs locally.
This patch introduces the generation of the required PMKs locally for
FT-PSK. Additionally, PMK-R0 is not stored (and thus pushed) for FT-PSK.
So for FT-PSK networks, no configuration of inter-AP communication is
needed anymore when using ft_psk_generate_local=1 configuration. The
default behavior (ft_psk_generate_local=0) remains to use the pull/push
protocol.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The reason detail field was removed from non_pref_chan attr in MBO
v0.0_r25 draft. Don't parse for this element to be compliant with the
latest drafr.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A weakness in the initial client taxonomy mechanism is from storing both
the Probe and Associate in struct sta_info. struct sta_info is created
after a client associates (or starts authentication frame exchange),
which means that any Probe Request frames sent prior to association are
not retained. The Associate Request frame has to be seen, and then
another Probe Request frame after association, before we have a
signature for the client.
Most clients send lots of Probe Request frames (lots and lots and lots
of Probes, actually), but a few do not. ChromeOS is notably sparing in
sending Probe Request frames, it can take a long time before a signature
for a ChromeOS device is available.
Store the most recent Probe Request frame in struct hostapd_sta_info
tracking list. When a struct sta_info is created, move the Probe Request
frame information from struct hostapd_sta_info to struct sta_info.
Signed-off-by: dgentry@google.com (Denton Gentry)
Signed-off-by: denny@geekhold.com (Denton Gentry)
Signed-off-by: rofrankel@google.com (Richard Frankel)
Signed-off-by: richard@frankel.tv (Richard Frankel)
Implement the signature mechanism described in the paper
"Passive Taxonomy of Wifi Clients using MLME Frame Contents"
published by Denton Gentry and Avery Pennarun.
http://research.google.com/pubs/pub45429.htmlhttps://arxiv.org/abs/1608.01725
This involves:
1. Add a CONFIG_TAXONOMY compile option. Enabling taxonomy incurs
a memory overhead of up to several kilobytes per associated
station.
2. If enabled, store the Probe Request and (Re)Associate Request frame in
struct sta_info.
3. Implement code to extract the ID of each Information Element,
plus selected fields and bitmasks from certain IEs, into a
descriptive text string. This is done in a new source file,
src/ap/taxonomy.c.
4. Implement a "signature qq:rr:ss:tt:uu:vv" command
in hostapd_cli to retrieve the signature.
Signatures take the form of a text string. For example, a signature
for the Nexus 5X is:
wifi4|probe:0,1,127,45,191,htcap:01ef,htagg:03,htmcs:0000ffff,vhtcap:338061b2,
vhtrxmcs:030cfffa,vhttxmcs:030cfffa,extcap:00000a0201000040|assoc:0,1,48,45,
221(0050f2,2),191,127,htcap:01ef,htagg:03,htmcs:0000ffff,vhtcap:339071b2,
vhtrxmcs:030cfffa,vhttxmcs:030cfffa,extcap:0000000000000040
Signed-off-by: dgentry@google.com (Denton Gentry)
Signed-off-by: denny@geekhold.com (Denton Gentry)
Signed-off-by: rofrankel@google.com (Richard Frankel)
Signed-off-by: richard@frankel.tv (Richard Frankel)
Previously, struct hostapd_iface sta_seen list head was initialized only
when completing interface setup. This left a window for operation that
could potentially iterate through the list before the list head has been
initialized. While the existing code checked iface->num_sta_seen to
avoid this case, it is much cleaner to initialize the list when struct
hostapd_iface is allocated to avoid any accidental missing of the extra
checks before list iteration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not generate an unused and invalid Request Authenticator (random
value) when constructing Accounting-Request packets. The correct Request
Authenticator is calculated subsequently in radius_msg_finish_acct()
using MD5(msg + shared secret).
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
Add configuration options that control publishing of fine timing
measurement (FTM) responder and initiator functionality via bits 70, 71
of Extended Capabilities element. Typically, FTM functionality is
controlled by a location framework outside hostapd. When framework is
activated, it will use hostapd to configure the AP to publish the FTM
functionality. See IEEE P802.11-REVmc/D7.0, 9.4.2.27.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Some deployed stations incorrectly consider nsts capability in
(Re)Association Response frame as required capability instead of maximum
capability and if it is greater than station's capability then beamform
will not happen in uplink traffic.
This commit adds support for an optional workaround to use station's
nsts capability in (Re)Association Response frame if the station's nsts
is less than AP by using the use_sta_nsts=1 configuration parameter.
This configuration is introduced in this commit and it is disabled by
default.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Previously, this was initialized in hostapd_setup_bss() which made it
possible for a REMOVE_NEIGHBOR control interface command to be issued
prior to the list head pointers having been set. That resulted in a NULL
pointer dereference. Fix this by initializing the list head at the time
the data structure gets allocated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Number of hostapd control interface commands (e.g., STATUS-DRIVER) could
result in NULL pointer dereference when issued on not yet enabled BSS.
Fix this by checking that the driver interface has been initialized
before calling the driver_ops function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Various checks should use is_multicast_ether_addr() instead
of hardcoding the equivalent, change it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not include a NAS-Port attribute in Access-Request and
Accounting-Request packets where the Association ID (AID) is 0, i.e.,
not yet assigned or known.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
This can be used to mandate the presence of the Message-Authenticator
attribute on CoA/Disconnect-Request packets.
Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
There's no need to have a separate variable and open-code a more
complicated version of this, just use is_broadcast_ether_addr().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, HT/VHT state was shown in STATUS based on the configuration
parameter instead of the runtime operational parameters. This could
result in claiming HT/VHT to be enabled even when it was forced to be
disabled due to an incompatible configuration. Clear HT/VHT information
in the STATUS output if HT/VHT has been disabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
reports mesh peer AID to kernel.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This allows the compiler to check that function prototypes match the
implementation. In addition, this gets rid of sparse warnings.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This moves pairwise, group, and management group ciphers to various mesh
data structures to avoid having to hardcode cipher in number of places
through the code. While CCMP and BIP are still the hardcoded ciphers,
these are now set only in one location.
Signed-off-by: Jouni Malinen <j@w1.fi>
The AMPE element includes number of optional and variable length fields
and those cannot really be represented by a fixed struct
ieee80211_ampe_ie. Remove the optional fields from the struct and
build/parse these fields separately.
This is also adding support for IGTKdata that was completely missing
from the previous implementation. In addition, Key RSC for MGTK is now
filled in and used when configuring the RX MGTK for a peer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation was incorrect in forcing the MGTK to be used
as the IGTK as well. Define new variable for storing IGTK and use that,
if set, to configure IGTK to the driver. This commit does not yet fix
AMPE element parsing to fill in this information.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the data structures to allow variable length MGTK to be
stored for RX. This is needed as an initial step towards supporting
different cipher suites.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is initial step in fixing issues in how PMF configuration for RSN
mesh was handled. PMF is an optional capability for mesh and it needs to
be configured consistently in both hostapd structures (to get proper
RSNE) and key configuration (not included in this commit).
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 0603bcb7fe ('hostapd: Process MAC
ACLs on a station association event (SME in driver)') processes MAC ACL
on a station association event for drivers which use AP SME offload but
does not consider the scenario where the drivers offload ACL. This can
result in station disconnection, though the driver accepts the
connection. Address this by avoiding the hostapd ACL check for the
drivers offloading MAC ACL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
eloop deinit calls could trigger segmentation fault if the early error
path is hit before eloop_init() gets called.
Signed-off-by: Jouni Malinen <j@w1.fi>
gas_address3=1 can now be used to force hostapd to use the IEEE 802.11
standards compliant Address 3 field value (Wildcard BSSID when not
associated) even if the GAS request uses non-compliant address (AP
BSSID).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously all TX status events with wildcard BSSID were ignored. This
did not allow Public Action frame TX status to be processed with the
corrected wildcard BSSID use. Fix this to be allowed. In practice, this
affects only test cases since Action frame TX status was not used for
anything else.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11-2012, 10.19 (Public Action frame addressing) specifies
that the wildcard BSSID value is used in Public Action frames that are
transmitted to a STA that is not a member of the same BSS. hostapd used
to use the actual BSSID value for all such frames regardless of whether
the destination STA is a member of the BSS.
Fix this by using the wildcard BSSID in cases the destination STA is not
a member of the BSS. Leave group addressed case as-is (i.e., the actual
BSSID), since both values are accepted. No such frames are currently
used, though.
This version is still using the AP BSSID value in the Address 3 field
for GAS response frames when replying to a GAS request with AP BSSID
instead of Wildcard BSSID. This is left as a workaround to avoid
interoperability issues with deployed STA implementations that are still
using the non-compliant address and that might be unable to process the
standard compliant case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds the necessary changes to support extraction and use of the
extended capabilities specified per interface type (a recent
cfg80211/nl80211 extension). If that information is available,
per-interface values will be used to override the global per-radio
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the simplest case of SAE group negotiation to occur by
selecting the next available group if the peer STA indicates the
previous one was not supported. This is not yet sufficient to cover all
cases, e.g., when both STAs need to change their groups, but at least
some cases are no covered.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd deinit functions were not ready to handle a case where the data
structures were not fully initialized. Make these more robust to allow
wpa_supplicant mesh implementation to use the current deinit design in
OOM error cases without causing NULL pointer dereferences.
Signed-off-by: Jouni Malinen <j@w1.fi>
This new parameter allows hostapd to add Vendor Specific elements into
(Re)Association Response frames similarly to the way vendor_elements
parameter can be used for Beacon and Probe Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 66d464067d ('FT: Register RRB
l2_packet only if FT-over-DS is enabled') disabled RRB l2_packet socket
if ft_over_ds is disabled, but this socket is required for FT
over-the-air, too (FT key distribution). Enable the socket regardless of
ft_over_ds setting if FT is enabled.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
Add FTM range request via RRM. The AP sends Radio measurement request
with FTM range request as a request for the receiving STA to send FTM
requests to the given list of APs. The neighbor report part of the
request is taken from the neighbor database.
The control interface command is:
REQ_RANGE <dst addr> <rand_int> <min_ap> <responder> [<responder>..]
dst addr: MAC address of an associated STA
rand_int: Randomization Interval (0..65535) in TUs
min_ap: Minimum AP Count (1..15); minimum number of requested FTM ranges
between the associated STA and the listed APs
responder: List of BSSIDs for neighboring APs for which a measurement
is requested
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a hostapd control interface command REQ_LCI to request LCI from an
associated station using radio measurement.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Save RM enabled capability element of an associating station if radio
measurement is supported in its capability field.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Process Neighbor Report Request frame and send Neighbor Report Response
frame based on the configured neighbor report data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Add a configurable neighbor database that includes the content of
Nighbor Report element, LCI and Location Civic subelements and SSID.
All parameters for a neighbor must be updated at once; Neighbor Report
element and SSID are mandatory, LCI and civic are optional. The age of
LCI is set to the time of neighbor update.
The control interface API is:
SET_NEIGHBOR <BSSID> <ssid=SSID> <nr=data> [lci=<data>] [civic=<data>]
To delete a neighbor use:
REMOVE_NEIGHBOR <BSSID> <SSID>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Extend the radio_measurements parameter to save all the supported
RRM capabilities as it's used in RM enabled capabilities element.
Make this parameter not directly configurable via config file (though,
keep the radio_measurements parameter for some time for backwards
compatibility). Instead, add a configuration option to enable neighbor
report via radio measurements. Other features can be added later as
well.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
The hostapd "POLL_STA <addr>" control interface command can be used to
check whether an associated station ACKs a QoS Data frame. The received
ACK for such a frame is reported as an event message ("AP-STA-POLL-OK
<addr>").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The optional tx=0 parameter can be added to the hostapd
DEAUTHENTICATE/DISASSOCIATE command to request disconnection without
transmitting the Deauthentication/Disassociation frame to the STA.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external programs to fetch the driver inactivity value for a
specific STA ("STA <addr>" hostapd control interface command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a legacy client with no P2P PS support is trying to connect to
a P2P GO, the driver should know that, and change its PS behavior
accordingly.
Add a parameter to hostapd_sta_add_params() indicating if P2P PS is
supported by the station and pass this parameter to kernel with nl80211
driver when the station is added/set.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Fix a possible memory leak in decode_tunnel_passwords() if an invalid
passphrase is received from the RADIUS server.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
This struct in the union is empty, but the design of using a zero-length
u8 array here is not fully compatible with C++ and can result in
undesired compiler warnings. Since there are no non-IE fields in the
Probe Request frames, get the location of the variable length IEs simply
by using the pointer to the frame header and the known header length.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was only used for providing an option to use linux/if_packet.h
instgead of netpacket/packet.h in src/ap/iapp.c. However,
netpacket/packet.h is nowadays commonly available and hostapd already
depends on it through src/l2_packet/l2_packet_linux.c, so there is no
need to continue to provide this option for the kernel header.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gets rid of need to include linux/if_vlan.h and additional defines
in vlan_ioctl.c to avoid issues with missing definitions in libc
headers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Due to both <netinet/in.h> (in "utils/includes.h") and <linux/in6.h> (in
<linux/if_bridge.h>) being included, the in6_addr is being redefined:
once from the C library headers and once from the Linux kernel headers.
This causes some build failures with for example the musl C library:
In file included from /usr/include/linux/if_bridge.h:18,
from ../src/ap/vlan_init.c:17:
/usr/include/linux/in6.h:32: error: redefinition of 'struct in6_addr'
/usr/include/linux/in6.h:49: error: redefinition of 'struct sockaddr_in6'
/usr/include/linux/in6.h:59: error: redefinition of 'struct ipv6_mreq'
Mixing C library and Linux kernel headers is a bit problematic [1] and
should be avoided if possible [2]. In order to fix this, define just the
macros needed from <linux/if_bridge.h> as done in Busybox for the brctl
applet [3].
[1] https://sourceware.org/bugzilla/show_bug.cgi?id=15850
[2] http://www.openwall.com/lists/musl/2015/10/06/1
[3] https://git.busybox.net/busybox/commit/?id=5fa6d1a632505789409a2ba6cf8e112529f9db18
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
With this, vlan_init.c does not need any special header files anymore
and vlan_ifconfig.c does not need hostapd-specific header files that
might conflict with net/if.h on NetBSD.
Signed-off-by: Jouni Malinen <j@w1.fi>
Move the ioctl-based VLAN implementation to a separate file to avoid
need for conditional blocks within vlan_ioctl.c. This removes the
internal CONFIG_VLAN_NETLINK define, i.e., this is now used only in
build configuration (.config) to select whether to include the
vlan_util.c (netlink) or vlan_ioctl.c (ioctl) implementation of the
functions.
Signed-off-by: Jouni Malinen <j@w1.fi>
caddr_t is legacy BSD and should be avoided [1]. While glibc may still
use __caddr_t as the type, Linux kernel does not (it is "void __user *
ifru_data").
This fixes compile errors with the musl libc:
../src/ap/vlan_init.c: In function 'br_delif':
../src/ap/vlan_init.c:218:18: error: '__caddr_t' undeclared (first use in this function)
ifr.ifr_data = (__caddr_t) args;
[1] http://stackoverflow.com/questions/6381526/what-is-the-significance-of-caddr-t-and-when-is-it-used
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
pmksa->pmk or pmksa->pmkid cannot be NULL since they are arrays. Remove
the unnecessary NULL checks and use the provided pmksa pointer directly
to simplify the implementation. (CID 138519)
Signed-off-by: Jouni Malinen <j@w1.fi>
Interface additions/removals are not guaranteed to be for the driver
listening to the kernel events. As such, send the events to
wpa_supplicant_event_global() which can then pick the correct interface
registered with wpa_supplicant to send the event to.
Signed-off-by: Roy Marples <roy@marples.name>
Commit 1889af2e0f ('VLAN: Separate station
grouping and uplink configuration') added an ap_sta_set_vlan() function
that gets called from pmksa_cache_auth.c. This broke CONFIG_IBSS_RSN=y
build if src/ap/sta_info.c did not get included in the build, i.e., if
CONFIG_AP=y was not set.
Fix this by making the ap_sta_set_vlan() call conditional on
CONFIG_NO_VLAN being undefined and define this for CONFIG_IBSS_RSN=y
builds. This is fine for wpa_supplicant since CONFIG_AP=y case was
already defining this. For hostapd, this function call is not needed for
CONFIG_NO_VLAN case either.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This patch add functionality of mesh SAE PMKSA caching. If the local STA
already has peer's PMKSA entry in the cache, skip SAE authentication and
start AMPE with the cached value.
If the peer does not support PMKSA caching or does not have the local
STA's PMKSA entry in the cache, AMPE will fail and the PMKSA cache entry
of the peer will be removed. Then STA retries with ordinary SAE
authentication.
If the peer does not support PMKSA caching and the local STA uses
no_auto_peer=1, the local STA can not retry SAE authentication because
NEW_PEER_CANDIDATE event cannot start SAE authentication when
no_auto_peer=1. So this patch extends MESH_PEER_ADD command to use
duration(sec). Throughout the duration, the local STA can start SAE
authentication triggered by NEW_PEER_CANDIDATE even though
no_auto_peer=1.
This commit requires commit 70c93963ed
('SAE: Fix PMKID calculation for PMKSA cache'). Without that commit,
chosen PMK comparison will fail.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA_FLUSH control interface command to
allow the PMKSA list from the authenticator side to be flushed for AP
and mesh mode. In addition, this adds a hostapd PMKSA_FLUSH control
interface command to flush the PMKSA entries.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This extends the wpa_supplicant PMKSA control interface command to allow
the PMKSA list from the authenticator side to be listed for AP and mesh
mode. In addition, this adds a hostapd PMKSA control interface command
to show the same list for the AP case.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
In scenarios where only DFS channels are available (e.g., outdoor,
special country codes), hostapd must be able to handle situations
where all are unavailable.
The two possibilities to get there are
1) while operating on the last available DFS channel a radar is
detected
2) hostapd is started while all channels are unavailable
In both cases, hostapd instead of terminating should better
wait for the NOPs to pass and re-try operation after the CAC.
This patch provides that feature by using the condition
(iface->state == HAPD_IFACE_DFS && !iface->cac_started)
as NOP mode signature to retry operation from within
hostapd_dfs_nop_finished().
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
