This enhances the test pmksa_cache_preauth_vlan_used to check
connectivity in the correct VLAN bridge.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
The use of the newer OpenSSL API in openssl_hmac_vector() removes one of
the memory allocations, so the TEST_ALLOC_FAIL here could not trigger.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that num_plinks is decremented properly if a peer mesh STA
reconnects without closing the link explicitly.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case for enforcing that AP setup fails in case there is need
to fall back to 20 MHz channel due to invalid 40 MHz configuration.
Modify this to allow successful AP startup as long as 40 MHz channel
does not get enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that the persistent group information gets dropped based
on peer response (unknown group) and that a new group formation can be
completed after such invitation failure.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previous version expired in January. The new ones are from running
ec-generate.sh and ec2-generate.sh again.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a regression test case for hostapd bug where the
disconnection/deauthentication TX status callback timeout could be
forgotten after new association if no ACK frame was received and the STA
managed to reconnect within two seconds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The OpenSSL memory allocation changes broke this test case. Fix this by
removing the cases that do not get triggered anymore and add a separate
wpas_ctrl_error test case to cover the fail_test() versions of errors.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use helper variable to indicate end of the test case instead of having
to use a fixed length of the loop.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to fix ap_wpa2_eap_psk_oom, ap_wpa2_eap_sim_oom,
eap_proto_psk_errors, and ap_ft_oom with the new OpenSSL dynamic memory
allocation design.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These need to be run without realm in the identity value to allow the
realm from the anonymous_identity to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These test cases verify that EAP-SIM with external GSM auth supports the
use case of replacing the SIM. The first test case does this incorrectly
by not clearing the pseudonym identity (anonymous_identity in the
network profile) while the second one clears that and shows successful
connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible to hit an error case in ap_wpa2_eap_in_bridge where the
selectedMethod STATUS field was not available. This resulted in not very
helpful "'selectedMethod'" message in the test log file. Make this
clearer by dumping all received STATUS fields and a clearer exception
message indicating that selectedMethod was missing.
Signed-off-by: Jouni Malinen <j@w1.fi>
The test cases discovery_ctrl_char_in_devname and discovery_group_client
tried to allow three P2P_FIND instances to be used before reporting an
error. However, this did not really work properly since the second and
third attempts would likely fail to start the initial special P2P_FIND
scan due to an already ongoing p2p_scan operation. Fix this by stopping
the previous P2P_FIND and waiting for the scan to complete if a retry is
needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that there is no NULL pointer dereference when the AP code
processes Probe Request and (Re)Association Request frames with a P2P IE
in case P2P support is explicitly disabled on the AP mode interface.
This is a regression test case for the fixes in the previous commit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Couple of waits for this event used the "GO-NEG-FAILURE" string instead
of the full event prefix. While this worked in the tests due to a
substring matching, it is better to use the full event prefix here.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the dump_monitor() call to drop a P2P-GO-NEG-FAILURE
event that was indicated quickly after the P2P_CONNECT command was
issued. This could result in grpform_reject test case failing to see the
expected event and fail the test due to "Rejection not reported".
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
rsn_ie_proto_eap_sta followed by eap_ttls_mschapv2_session_resumption
showed a failure case where the special RSNE from rsn_ie_proto_eap_sta
ended up remaining in a wpa_supplicant BSS entry and the SELECT_NETWORK
command used the previous scan results without checking for changed AP
configuration. This resulted in test failure due to RSN IE being claimed
to be different in EAPOL-Key msg 3/4. This is not really a real world
issue, but try to avoid false failure reports by explicitly clearing the
BSS table at the end of rsn_ie_proto_eap_sta.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that the previous commit works correctly by forcing a
P2P_LISTEN command execution to be interupted by a P2P_FIND command
timed in a manner that forces it to show up before the kernel ROC has
started for the Listen.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that P2P_STOP_FIND stops a pending offchannel TX wait in
the kernel by checking that a listen operation can be started in less
than a second after stopping a pending Action frame TX. This verifies
that the optimization introduced in the previous commit works properly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This reverts commit be9fe3d8af. While I
did manage to complete multiple test runs without failures, it looks
like this change increases full test run duration by about 30 seconds
when using seven VMs. The most visible reason for that seems to be in
"breaking" active scanning quite frequently with the Probe Response
frame coming out about 40 ms (or more) after the Probe Request frame
which is long enough for the station to already have left the channel.
Since this logging change is not critical, it is simplest to revert it
for now rather than make changes to huge number of test cases to allow
more scan attempts to be performed before timing out.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previously used 10 second timeout allowed only two scan attempts
(five seconds between scans) and it was possible to hit a failure every
now and then when running under heavy load and the Probe Response frame
got delayed by 40 ms or so twice in a row. Add more time for one more
scan attempt to reduce the likelihood of this happening.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These test caases depended on a single active scan round finding the AP.
It is possible for the Probe Response frame to get delayed sufficiently
to miss the response especially when testing under heavy load with
multiple parallel VMs. Allow couple of scan retries to avoid reporting
failures from these test cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use the group SSID (if known) when requesting a join operation. This
makes some of the P2PS test cases more robust in cases where previously
executed tests have added older groups into the cached scan results with
the same MAC addresses and an incorrect BSS could have been picked
previously.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it less likely to hit issues with running out of control
interface TX queue when running multiple FST test in a row. Number of
the FST operation sequences seemed to leave quite a few event messages
pending in one of the attached control interface sockets for wlan5 which
could result in test failure if the buffer space ran out and some of the
wpa_supplicant events were not delivered.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is better to get these messages into the actual debug log instead of
hoping they will be noticed from stdout.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This test case used to leave the dynamically added wlan5 interface in a
state where it was still trying to reconnect to a network. This could
result in the following test cases being unable to clear the cfg80211
scan cache. Avoid this type of issues by explicitly stopping the
connection attempt and making sure that there are no scan results in the
cache at the end of connect_cmd_disconnect_event.
The following test case sequence triggered a failure due to the
remaining BSS table entry:
connect_cmd_disconnect_event connect_cmd_wep ap_hs20_random_mac_addr
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible to hit a race condition between WPS_CANCEL and
immediately following WPS_PIN command. Wait for a disconnection event to
avoid that. This was seen with the following test case sequence:
ap_wpa2_psk_supp_proto_wrong_group_key_len ap_wps_probe_req_ie_oom
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When running tests, make printk put all messages, including debug
messages, onto the serial console to go into the console file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wait for the AP-DISABLED and AP-ENABLED group events before reading the
current group operation frequency after P2P-REMOVE-AND-REFORM-GROUP.
This reduces a possibility of a race condition making a test case fail
with the returned frequency being 0 when reading this before the
reformed group is fully up. This may help avoid false error reports for
the following test cases: p2p_go_move_reg_change p2p_go_move_scm
p2p_go_move_scm_peer_supports p2p_go_move_scm_multi.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed for number of EAP test cases at least when using the
internal TLS server implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since wpa_supplicant is now retrying GAS comeback failures once, the
gas_anqp_oom_hapd test case started failing. Fix this by updating the
test case to expect success (on the retry).
Signed-off-by: Jouni Malinen <j@w1.fi>
This is in preparation of a wpa_supplicant change to allow GAS retries
which can result in the previous test case design showing failures due
to "unexpected" management frames (GAS Initial Request from the retry).
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds some more test coverage for phase1 parameters that had not
previously been included in any of the test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
These test cases were supposed to clear the cfg80211 and wpa_supplicant
scan caches in the end to avoid causing issues to the following test
cases. This did not work properly after introduction of the support for
aborting a pending scan. Fix this by using the flush_scan_cache()
function and waiting within the test case until the final scan operation
completes.
This issue was triggered by ssid_hidden/ssid_hidden2 followed by
ext_password_interworking (though, not every time).
Signed-off-by: Jouni Malinen <j@w1.fi>
The rfkill initialization will be moved out from
wpa_driver_nl80211_drv_init() which would break one step in this OOM
test case due to the memory allocation not existing anymore. Fix this by
skipping that OOM step to avoid causing false failures with the
following commits.
Signed-off-by: Jouni Malinen <j@w1.fi>
This speeds up and clarifies error reporting for cases where the GO
fails to start in invitation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for testing CRDA since it means you can use EPATH to
redirect the test scripts to a different crda binary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds more coverage for TDLS testing for a case where the direct
link should use various VHT channel bandwidths.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The decrypted copy of a GTK from EAPOL-Key is cleared from memory only
after having sent out CTRL-EVENT-CONNECTED. As such, there was a race
condition on the test case reading the wpa_supplicant process memory
after the connection. This was unlikely to occur due to the one second
sleep, but even with that, it would be at least theorically possible to
hit this race under heavy load (e.g., when using large number of VMs to
run parallel testing). Avoid this by running a PING command to make sure
wpa_supplicant has returned to eloop before reading the process memory.
This should make it less likely to report false positives on GTK being
found in memory.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to see where in memory the key was found and what
there is in memory around that location.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
init=CORE was previously used due to invalid db.txt data for 00. For
now, allow both it and the new init=USER after fixed db.txt.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case could fail if the cfg80211 scan cache brought in a BSS
entry from an earlier test case and a new scan did not get executed
prior to the ROAM command. Fix this by forcing the scan to go through
prior to roaming to AP2
This issue showed up with the following test case sequence:
connect_cmd_roam pmksa_cache_opportunistic_connect
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like it is possible for the GTK to be found from memory every
now and then. This makes these test cases fail. Write the memory
addresses in which the GTK was found to the log to make it somewhat
easier to try to figure out where the key can be left in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the BSSs object property change signal to be
generated during the OOM test case for Get(). If that happened, the
signal was not sent out, but the following Get(BSSs) operation succeeded
unexpectedly which resulted in a test failure. Make this less likely to
happen by waiting 50 ms between the scan and Get(BSSs) operation. This
should be sufficient to cover most cases since wpa_supplicant uses 5 ms
timeout for D-Bus property changed updates.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the AP's Beacon frame to be seen by dev[0] when
running a scan. This is not an error case. Make this test case more
robust by verifying with a sniffer whether a Probe Response frame was
sent to unexpected STA.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies client private key use in encrypted PKCS #8 format with
PKCS #5 v1.5 format using pbeWithMD5AndDES-CBC and PKCS #5 v2.0 format
using PBES2 with des-ede3-cbc.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that P2P_CANCEL gets rejected on fully re-invoked persistent
group. This did not work properly before the last couple of commits and
before this week, the P2P_CANCEL on a separate group interface in P2p
Client role could result in use of freed memory and process termination.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for a cached scan entry in cfg80211 from an earlier test
case to show up while verifying that the disabled AP does not show up in
scan results. This could result in invalid test failures, e.g., when
running test cases "ap_require_ht ap_multi_bss_config" multiple times
(depends a bit on timing). Make this less likely to occur by explicitly
clearing the scan cache and by stopping wlan1 from trying to associate
before stopping ap_required_ht* test cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Only one of the ERs was stopped at the end of the test case and this
could result in the following test case failing, e.g., when executing
this test case sequence: ap_wps_er_multi_add_enrollee ap_wps_upnp.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for this test case to fail if the single attempt of
discovering the peer as part of the scan for join failed. This test case
was useful in combination with another test case:
ap_hs20_fetch_osu autogo_join_auto_go_neg
However, there is now an explicit test case (discovery_after_gas) for
this, so autogo_join_auto_go_neg can be made more robust without losing
testing coverage.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The P2P channel list on dev[1] at the end of
p2p_go_move_scm_peer_does_not_support was empty because all of the 2.4
GHz band got disabled by the simulated avoid frequencies driver event.
That channel list needs to be cleared prior to resetting regulatory
domain back to world roaming to get the P2P channel list updated
properly for the following test cases.
This was triggered by the following test case sequence:
p2p_go_move_scm_peer_does_not_support persistent_group_and_role_change
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that both the GO and P2P Client processing of P2P group formation
timeout removes the correct group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This reverts commit 78fdab307e. This test
case needs MCC support on two stations, so the earlier attempt to handle
this with one dynamic interface is not sufficient.
Signed-off-by: Jouni Malinen <j@w1.fi>
Now that vm-run.sh supports a long list of test cases without crashing
the VM kernel, there is no need to use the "parallel-vm.py -1 1 <tests>"
workaround. Print the re-run example commands with vm-run.sh instead. In
addition, add the --long argument if it was specified for the test run
to avoid skipping test cases in the re-run case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it more likely for the two ERs to go through WPS UPnP
exchange in parallel. This was already happening every now and then and
resulted in failures. However, now that there is support for multiple
concurrent exchanges, it is useful to have this test case hit that
possibility more frequently.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The script is currently limited by the maximum kernel command line
length and if that's exceeded the kernel panics at boot. Fix this by
writing the arguments to a file and reading it in the VM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This test case fails with the current internal TLS client implementation
since the needed altsubject_match parameter is not yet supported.
Signed-off-by: Jouni Malinen <j@w1.fi>
The internal TLS implementation in wpa_supplicant supports TLS v1.2, so
verify that this version can be disabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since the internal TLS client implementation in wpa_supplicant now has
sufficient support for this functionality, allow the test case to be
executed.
Signed-off-by: Jouni Malinen <j@w1.fi>
gcc 4.8 vs 5.2 seem to compile eloop_register_sock() differently. With
5.2, that function name does not show up in the backtrace since
eloop_sock_table_add_sock() is used without a separate function call.
This broke the memory allocation failure checking in this test case. Fix
this by matching against the eloop_sock_table_add_sock() function which
shows up in the backtrace for both gcc versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
If hostapd AP started unexpectedly, this test case would fail with
NameError due to incorrect variable name being used to construct the
exception text.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed for proper test execution. The recently added VHT 80+80
test cases started verifying channel bandwidth on the station side and
those checks fail if wpa_supplicant is built without
CONFIG_IEEE80211AC=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
If /tmp has a relatively small size limit, or multiple people run the
tests on the same machine, using the same output directory can easily
cause problems.
Make the test framework honor the new HWSIM_TEST_LOG_DIR environment
variable to make it easier to avoid those problems.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If wmediumd is available on the path, test that it can forward
packets between two virtual nodes and that stopping it makes
the regular in-kernel datapath do the needed work again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no need to wait for the initial client timeout in this type of
test sequence since that wait can be cleared by connecting and
disconnecting a client to the group. This allows the test case to be
executed much more quickly and the dependency on --long can be removed.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to wait for the initial client timeout in this type of
test sequence since that wait can be cleared by connecting and
disconnecting a client to the group. This allows the test case to be
executed much more quickly and the dependency on --long can be removed.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to wait for the initial client timeout in this type of
test sequence since that wait can be cleared by connecting and
disconnecting a client to the group. This allows the test case to be
executed much more quickly and the dependency on --long can be removed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a dynamically added HWSimRadio to allow the MCC case to be covered
with a single test run with the mac80211_hwsim default radios disabling
MCC.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a dynamically added HWSimRadio to allow the MCC case to be covered
with a single test run with the mac80211_hwsim default radios disabling
MCC.
In addition, remove dependency on --long since this test case does not
really take that long.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a dynamically added HWSimRadio to allow the MCC case to be covered
with a single test run with the mac80211_hwsim default radios disabling
MCC.
In addition, remove dependency on --long since this test case does not
really take that long (just couple of seconds).
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to wait for the initial client timeout in this type of
test sequence since that wait can be cleared by connecting and
disconnecting a client to the group. This allows the test case to be
executed much more quickly and the dependency on --long can be removed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a dynamically added HWSimRadio to allow the MCC case to be covered
with a single test run with the mac80211_hwsim default radios disabling
MCC.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a dynamically added HWSimRadio to allow the MCC case to be covered
with a single test run with the mac80211_hwsim default radios disabling
MCC.
Signed-off-by: Jouni Malinen <j@w1.fi>
Convert p2ps_channel_active_go_and_station_different_mcc to use a
dynamically added HWSimRadio to allow the MCC case to be covered with a
single test run with the mac80211_hwsim default radios disabling MCC.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the run_tshark() operations more reliable while still
allowing to reduce the extra wait by forcing wlantest to flush the
packets to the pcapng file.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the test log more readable by converting the values to
integers and sorting the array.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies the nl80211 behavior to abort a scan on an explicit
control interface request and on connection request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This syncs the test cases with the implementation change in station's MB
IE creation. FST tests should expect MB IE regardless of the station
connection state and whether the current connection is FST-enabled or
not. This fixes the follow test cases that started reporting failures
with the previous commit change in src/fst/fst_group.c:
fst_disconnect_1_of_2_stas_from_non_fst_ap
fst_sta_connect_to_non_fst_ap
fst_second_sta_connect_to_non_fst_ap
fst_disconnect_2_of_2_stas_from_non_fst_ap
fst_second_sta_connect_to_fst_ap
fst_disconnect_1_of_2_stas_from_fst_ap
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a test to verify that a P2P GO does not start a CSA
once invitation signalling is done, and the P2P client is
about to connect.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This test case was failing if a PropertiesChanged signal for P2P peer
gets delivered from a previous test case. Avoid that by waiting for the
new group to be formed before processing any PropertiesChanged signals.
This failure was triggered by the following test case sequence:
dbus_p2p_two_groups dbus_p2p_group_idle_timeout
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like a previous P2P test case can cause the initial single
channel scan in ap_open_select_twice take more than five seconds in some
cases. While that is not really expected behavior, this test case should
not fail. Increase the timeout to avoid reporting false failures here.
This could be triggered with the following test case sequence:
p2p_msg_unexpected_go_neg_resp ap_open_select_twice
Signed-off-by: Jouni Malinen <j@w1.fi>
These test cases depend on the HT40 co-ex scans not swapping PRI/SEC
channels. It was possible for a test case to fail, e.g., in the
following sequence: ap_ht40_5ghz_match ap_vht80b.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that the second SELECT_NETWORK for the same network starts
a new scan immediately if the previous connection attempt is waiting for
the next scan iteration to start.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This avoids issues with following test cases failing due to unexpected
starting state. This issue showed up with the following hwsim test case
sequence:
fst_setup_mbie_diff fst_dynamic_iface_attach
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the WPS PBC state to get cached through to the
following test cases and that would trigger false failures. Fix this by
explicitly clearing the scan cache at the end of ap_wps_per_station_psk.
This issue was triggered with the following test case sequence:
ap_wps_per_station_psk autogo_pbc
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed since the forced OOM may have forced the cached
information to be invalid or dropped. This issue was hit with the
following hwsim test case sequence:
ap_interworking_scan_filtering fst_sta_config_llt_large dbus_connect_oom
wpas_ctrl_enable_disable_network
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for dev[2] to be left with non-default config_methods
parameter at the end of the test case and that could result issues in
following test cases. This hit a failure in the following sequence:
wpas_ctrl_set_wps_params p2ps_channel_active_go_and_station_same
Signed-off-by: Jouni Malinen <j@w1.fi>
Due to a typo in a function name, this test case ended up running
without the final cleanup. That could result in the following test cases
failing, e.g., when running this sequence:
wifi_display_parsing dbus_p2p_go_neg_auth
Signed-off-by: Jouni Malinen <j@w1.fi>
The previously used invalid values will become allowed with the
following commits, so change the test case to use values that both were
and will continue to be invalid to avoid unnecessary failures.
Signed-off-by: Jouni Malinen <j@w1.fi>
autogo_scan verifies the special case where a Probe Response frame
without P2P IE has been received from a GO (e.g., due to a non-P2P
interface requesting a scan) and P2P information from a Beacon frame
needs to be used instead to determine that the group is persistent.
Signed-off-by: Jouni Malinen <j@w1.fi>
SAVE_CONFIG command on the global control interface tries to save
the config file on all interfaces. The test disabled updating the
config file only on one interface, thus for configurations that
support a dedicated P2P Device interface, saving the config file
would still have succeeded on the P2P Device interface.
Fix the test by disabling updating the configuration file on the global
control interface (which will, in practice, disable this for the P2P
Device interface) in addition to disabling it on the main interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
mac80211_hwsim only supports 2 different MAC addresses.
Configurations that use a dedicated P2P Device interface already
use these 2 addresses, so adding another interface on the same
PHY results in a duplicated MAC address.
Fix this by changing the MAC address of the added interface to make
sure the new interface has a unique MAC address.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Set the bridge ageing to 1 sec to make the bridge clear unused
addresses after this interval. Otherwise the test depends on
the local configuration of brctl.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Write the main interface address to the tkip_mic_test debugfs file
to generate Michael MIC failure event (which is different than the
p2p_dev_addr when a dedicated P2P Device interface is used).
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
These test cases verify behavior with parallel scan operations while
going through GO Negotiation and duplicated GO Negotiation Request frame
RX with not-yet-ready sequence in GO Negotiation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
send_iface_detach_request() can fail and that resulted in skipping a
call to restore_reg_domain() and leaving unexpected country
configuration for following test cases. This could result in failures,
e.g., in this sequence: fst_proto wpas_mesh_open_5ghz
Fix this by ignoring exceptions from send_iface_detach_request() and
continuing to restore regulatory domain.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
I modified this test case for commit
eabf083984 ('tests: P2PS channel
handling') to use dev[2] instead of dev[0], but forgot to update the
p2ps_connect_p2ps_method() dev list to match that. Fix this to actually
use a concurrent connection.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the dbus_interface test case to leave the P2P
channel lists with 5 GHz channels enabled due to the special driver=none
case. This could make the following P2P test case fail due to selecting
an unexpected channel. Fix this by forcing P2P channel list update at
the end of the dbus_interface test case.
This was triggering with the following hwsim test case sequence:
dbus_interface p2ps_connect_adv_go_p2ps_method_group_iface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use a dynamic HWSimRadio in p2ps_channel_sta_connected_disallow_freq_mcc
to allow MCC test case to be executed in default setting (MCC disabled
for the default radios).
Signed-off-by: Jouni Malinen <j@w1.fi>
Stop the pending P2P_LISTEN operation priot to issuing P2P_GROUP_ADD to
start a GO. This avoids excessively long wait for the previous Listen
step to complete before being able to start the GO. This makes
p2ps_connect_adv_go_persistent take significantly less time.
Signed-off-by: Jouni Malinen <j@w1.fi>
The combination of starting P2P extended listen and issuing
P2P_ASP_PROVISION_RESP almost immediately after that while in P2P_LISTEN
state resulted in caes where the advertiser could end up going back to a
long listen state while trying to retransmit PD Request. This resulted
in p2ps_provision() timing out while waiting for P2PS-PROV-DONE
especially in p2ps_feature_capability_* test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify OCSP stapling response that is signed by the CA rather than a
separate OCSP responder. In addition, verify that invalid signer
certificate (missing OCSP delegation) gets rejected.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a test case verifying deferred P2PS provision discovery when an
advertiser sends the status 11 (Fail: reject by user) in the follow-on
PD Request.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Not doing so may result in a deferred PD flow failure (currently the
hwsim tests succeeded because seeker never stopped find, spending enough
time listening, so the follow-on PD would succeed).
Fix this by calling p2p_ext_listen when the seeker receives a deferred
PD failure event. Cancel extended listening when PD is done and also
stop find when seek is done.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Check that there are no unencrypted frames when using hostapd with VLANs
and WPA before the first station connects to the VLAN.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
These test cases left at least one of the attached monitor sockets
blocking for excessive time: ap_wpa2_eap_aka_ext,
ap_hs20_req_conn_capab_and_roaming_partner_preference,
ap_hs20_min_bandwidth_and_roaming_partner_preference, ap_wpa_ie_parsing.
Signed-off-by: Jouni Malinen <j@w1.fi>
At some point, these hostapd_oom_* test cases started to fail with
wpa_msg() allocation failure for the AP-ENABLED event. This resulted in
unnecessary long test execution (waiting 30 seconds for an event that
was dropped). Speed this up by using a shorter timeout.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case ended up hitting control socket output queue limit
unnecessarily due to the test script not reading pending event messages.
Signed-off-by: Jouni Malinen <j@w1.fi>
Number of test cases did not read all control interface socket events
from the dynamically added wlan5 interface. This could result in hitting
maximum socket TX queue length and failures in the following test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
connect_cmd_roam did not force a new scan to find the second AP. This
could result in failures due to the ROAM command getting rejected, e.g.,
in the following test case sequence: wext_pmksa_cache connect_cmd_roam.
Signed-off-by: Jouni Malinen <j@w1.fi>
Due to a serial number mismatch, the correct "revoked" status was not
used; instead "unknown" was used. While the test case would not fail for
this, incorrect code path was checked.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When the 'SET wpa 2' command is executed last, it seems to somehow
reset parts of the settings, causing hostapd to beacon with the
pairwise cipher suite selector set to 00-0F-AC:0 (none/use-group).
This is not permitted and should be rejected; wpa_supplicant also
cannot connect.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This verifies that ENABLE_NETWORK does not trigger reconnection if
already connected. The previous commit fixed a case where it was
possible for that to happen.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is a regression test case for the issue fixed by the previous
commit (hapd->num_probereq_cb not getting cleared on deinit).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to avoid issues in some cases where 8-bit bytestrings may
be present in the otherwise text debug log.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a Python-based minimal WSC protocol implementation to allow
more testing coverage to be reached for various error cases in protected
attributes. The wps_ext test case completes successful exchange in both
the Enrollee and Registrar roles acting in the middle of AP and STA. The
other test cases cover error cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends ap_wps_pbc_timeout to cover another long WPS timeout:
ER-initiated SetSelectedRegistrar timeout on AP. Using the same test
case for this avoids the need for another 120 second test case.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like NID_X9_62_prime192v1 is not available, so allow that group
to fail without failing the full ap_wpa2_eap_pwd_groups test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like NID_X9_62_prime192v1 is not available, so allow that group
to fail without failing the full sae_groups test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These test cases added a new radio for the non-FST AP and while they
removed the radio itself, they did not remove the hostapd instance for
that radio. Remove that to avoid leaving behind invalid instances.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies wpa_supplicant behavior in number of cases where the
external program opening a control interface socket does not behave
properly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
ap_open_sta_enable_disable verifies that DISABLE_NETWORK that is issued
while connect/sme-connect radio work is pending is effective, i.e.,
prevents connection to disabled network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The number of channels was not properly passed from the
run-all.sh script to the start.sh script. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add tests verifying a Coordination Protocol Transport exchange and
selection during P2PS provision discovery.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reuse p2ps_provision() and p2ps_connect_pd() methods, and
remove the previous PD helper functions which are no longer used.
This fixes the previously "broken"
p2ps_connect_keypad_method_nonautoaccept and
p2ps_connect_display_method_nonautoaccept.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Re-factor p2ps_connect_p2ps_method() so it reuses generic P2PS provision
and connection flows.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When MCC is enabled, the remain of channel scheduling might
incur additional delays, so increase the timeouts to be able
to receive delays frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Set peer_group_removed only if peer_group_added has already been set.
This fixes an issue where a propertiesChanged event triggered by an
earlier test case was able to get dbus_p2p_group_termination_by_go
terminated too early. This happened, e.g., with sequence
"dbus_p2p_two_groups dbus_p2p_group_termination_by_go".
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Only run peerJoined() steps once to avoid trying to use GetAll() on an
already removed group and double-removal of a group. This did not make
the test case fail, but the exception is printed out in pretty confusing
way to stdout, so better get rid of it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Remove the duplicated -ddKt command line argument to avoid setting
hostapd debug level to EXCESSIVE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
On recent kernels, it seems that something changed (scheduler?)
that makes hwsim send the scan done event so quickly that iw isn't
scheduled back in to listen for it, causing iw to get stuck.
Work around this by using the scan trigger command (it'll be quick
enough so that we don't really need to wait) and the scan trigger
and dump commands where the results are required (and use a small
sleep there instead of waiting for the scan results.)
I'll try to fix this separately in iw later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This verifies P2P extended listen timing operations by confirming that a
peer is not discoverable during the provisioning step and that the peer
becomes discoverable after having removed the group during such
provisioning step. The latter case was broken until the 'P2P: Cancel
group formation when deleting a group during group formation' commit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that Groups list for a P2P Peer gets updated properly on group
addition and removal (three different paths).
Signed-off-by: Jouni Malinen <j@w1.fi>
omac1_aes_128() implementation within crypto_openssl.c is used in this
case and that cannot fail the memory allocation similarly to the
non-FIPS case and aes-omac1.c.
Signed-off-by: Jouni Malinen <j@w1.fi>
OpenSSL rejects the cipher string 'EXPORT' in FIPS mode in a way that
results in the locally generated error showing up before the EAP method
has been accepted.
Signed-off-by: Jouni Malinen <j@w1.fi>
In addition, replace some of the CHAP cases with PAP since that enables
more coverage without breaking the main test focus.
Signed-off-by: Jouni Malinen <j@w1.fi>
The PKCS12 file with default openssl options cannot be used with OpenSSL
1.0.1 in FIPS mode. Replace this with -descert version as a workaround.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to build wpa_supplicant for OpenSSL FIPS mode
testing. wpa_supplicant/.config needs following type of configuration
for this:
CONFIG_FIPS=y
CFLAGS += -I/usr/local/ssl/include
LIBS += -L/usr/local/ssl/lib
CC=/usr/local/ssl/fips-2.0/bin/fipsld
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows driver-based preference list to override default operating
channel selection mechanism by using a non-social P2P find if needed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this was assumed to be the case due to default channel
selection behavior. However, that may not be the case with driver-based
preference list processing. Enforce a social channel to be used as the
operating channel here since dev[2] uses social channel only device
discovery and needs to find the GO.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The openssl_ciphers="EXPORT" case may result in locally generated
disconnection event if the OpenSSL version used in the build rejects
export ciphers in default configuration (which is what OpenSSL 1.1.0
will likely do). Don't report a test case failure in such a case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add adv_cpt and seeker_cpt parameters to p2ps_provision() function.
The seeker_cpt is used in P2P_ASP_PROVISION command by a seeker, the
adv_cpt parameter is in P2P_ASP_PROVISION_RESP by an advertiser.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add an optional parameter to p2ps_advertise() function allowing to
specify CPT priority values.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add an optional CPT parameter to asp_provision() method of
WpaSupplicant.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add p2ps_connect_pd() helper method which strictly validates the PD
results and establishes the connection between peers accordingly.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add generic provision method. This method receives a seeker and an
advertiser devices, advertisement id, method, and a flag which indicates
whether deferred flow is expected. The method returns P2PS-PROV-DONE
events and the pin (if keypad or display method is used).
This method is needed to simplify the P2PS provision flows in the tests.
This method complies to the P2PS specification regarding the expected
order of the show and display PIN events.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add asp_provision method which issues either P2PS PD Request or, if the
status is provided, continues the deferred flow by sending follow on
PD Request.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
This test case could fail if there were old BSS entries remaining in
cfg80211 scan results. That happened, e.g., when running test cases in
the following sequence: "discovery_social_plus_one discovery_auto".
Signed-off-by: Jouni Malinen <j@w1.fi>
This removes quite a bit of duplicated code. In addition, this starts
using different FST group names to get additional coverage.
Signed-off-by: Jouni Malinen <j@w1.fi>
Without this, the run-tests.py socket could have been left in attached
to receive all hostapd global events during a test case. This could hit
the limit of pending messages on the socket since there is nothing
clearing this socket during the execution of a test case. Fix this by
explicitly closing the socket after having completed the RELOG command.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies FST group dialog_token wrap-around and behavior with large
number of session setups and teardowns.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds a test case that goes through session initialization through
separate commands that can be modified more easily for special case. The
first such special case is using special FST Setup Request frames with
non-standard MBIE contents to hit different code paths for finding the
interface.
Signed-off-by: Jouni Malinen <j@w1.fi>
Pass absolute path to the daemonized wpa_cli process and add read
privileges for everyone on the action script to make this test case work
better when run without a VM.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Try to use the special build for --codecov purposes, if present, instead
of hardcoding the hostapd/wpa_supplicant binary to the default location.
This is needed to collect code coverage correctly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 53606b105c ('tests: Wait for scan
to complete on all interfaces in reset()') added option of passing
ifname to get_driver_status(). This could result in FAIL-NO-IFNAME-MATCH
returns that get printed out in "Ignore unexpected status-driver line"
messages if the interface is not found. Check for this case to avoid
that unnecessary print.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Remove unused variables and replace split(" ") with just split().
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
When WpaSupplicant executes reset() it waits until all the ongoing scans
are completed. However, it checks the status of the wlanX interface
only. If a dedicated P2P device interface is used, scan may be still
running on the P2P Device interface, e.g., due to P2P_FIND. This might
affect subsequent tests.
Fix this by waiting until the scan is done both on wlanX and P2P
Device interfaces.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
This allows hostapd and wpa_supplicant to be built for hwsim test cases
with ubsan functinality from the recent gcc/clang compiler versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
