Add a new QCA vendor specific feature capability indication for the
device to indicate the support of TWT.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The current/default behavior of set blacklist BSSID QCA vendor command
is a mandate to the driver - do not consider this BSSID for connect/roam
till reset.
There are use cases where this need not be a mandate and thus could
provide the flexibility for the driver to consider this BSSID if there
are no better ones. Such use cases can use this new flag attribute to
only hint the blacklist of a BSSID to the driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This new QCA vendor attribute adds provision to specify the
ethernet protocol id from userspace to the packets which are
offloaded to the driver/firmware (e.g., IPv4, IPv6).
Signed-off-by: Arun Kumar Khandavalli <akhandav@codeaurora.org>
Allow user space applications to check whether wlan firmware is alive
through an nl80211 vendor command.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This new QCA vendor attribute indicates the EVM value in netlink.
Signed-off-by: stonez <stonez@codeaurora.org>
:100644 100644 ad5dac2... ede4fc8... M src/common/qca-vendor.h
The vendor command QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY was defined
to carry the list of avoid frequencies that aim to avoid any
interference with other coexistencies. This recommendation was followed
strictly by trying to prevent WLAN traffic on the impacted channels.
This commit refines the expectation of the interface by defining this
avoid channel list to allow minimal traffic but not heavier one. For
example, P2P may still be able to use avoid list frequencies for P2P
discovery and GO negotiation if the actual group can be set up on a not
impact channel.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define QCA vendor command attributes to configure HE +HTC support and
HE operating mode control transmission. This is used to configure the
testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This new QCA vendor command is used to query the supported AKM suite
selectors from the driver. There has been no such capability indication
from the driver and thus the current user space has to assume the driver
to support all the AKMs. This may be the case with some drivers (e.g.,
mac80211-based ones) but there are cfg80211-based drivers that implement
SME and have constraints on which AKMs can be supported (e.g., such
drivers may need an update to support SAE AKM using
NL80211_CMD_EXTERNAL_AUTH). Allow such drivers to specify the exact set
of supported AKMs so that user space tools can determine what network
profile options should be allowed to be configured. This command returns
the list of supported AKM suite selectors in the attribute
NL80211_ATTR_AKM_SUITES.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit enhances QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES to
also be an event, aimed to notify the link status (EX: connected
stations status on an AP link).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG vendor command
to set the priorities among different types of traffic of
WLAN/BT/Zigbee during coex scenarios.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add interface for drivers to report changes in TX/RX throughput
dynamically to user space. This information can be used by userspace
tools to tune kernel's TCP parameters in order to achieve peak
throughput. The driver may optionally provide guidance on which TCP
parameters to be configured for optimal performance along with the
values to be configured.
The TCP parameters that need to be tuned for peak performance are not
interface specific. Based on the guidance from the driver and
considering the other interfaces that may be affected with the new
configurations, a userspace tool has to choose the values to be
configured for these parameters to achieve optimal performance across
interfaces.
The throughput levels informed by the driver with this event are only
for providing guidance on TCP parameter tuning from userspace. The
driver may change the thresholds used to decide low or medium or high
throughput levels based on several parameters based on the PHY layer
capacity in the current connection, the number of packets being
dispatched per second, or the number of packets pending in queues, etc.
The throughput levels may not be consistent with the actual throughput
of the link.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure action
frame transmission in HE trigger based PPDU.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure HE
single user PPDU transmission.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attributes to configure HE
operating mode control field bandwidth, number of spatial streams, and
UL MU disable configuration. Define a new attribute to clear the
previously set HE OM control field configuration. This is used for
testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add NAN NDP attribute QCA_WLAN_VENDOR_ATTR_PEER_NDPE_SUPPORT which
indicates if NDP remote peer supports NDPE attribute or not.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a subcommand for Channel Frequency Response (CFG) Capture
Configuration and define attributes for configuring CFR capture
parameters per peer and enabling/disabling CFR capture.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Driver/firmware does roam scan when it finds the need to roam to a
different BSS. Add a QCA vendor event to indicate such roam scan events
from driver/firmware to user space.
Please note that some drivers may not send these events in few cases,
e.g., if the host processor is sleeping when this event is generated in
firmware to avoid undesired wakeups.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new QCA vendor specific test config attribute to configure the
support for receiving the MPDU with operating mode control subfield.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The payload used for the existing NAN vendor command,
QCA_NL80211_VENDOR_SUBCMD_NAN is a binary blob of data. This
command is not extendable to send additional information. Hence
define a new vendor command QCA_NL80211_VENDOR_SUBCMD_NAN_EXT,
that can carry the binary blob encapsulated within an attribute
and can carry additional attributes to enhance the NAN command
interface. Define additional 3 new attributes for conveying
type of NAN subcmd and channel information.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Present implementation of NAN vendor command does not use
attribute encapsulation for sending the command from userspace
to the driver, payload is directly sent as is. Attribute
QCA_WLAN_VENDOR_ATTR_NAN is used only for receiving vendor
events in the userspace from the driver. Update the doc as per
this implementation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The max supported ADDBA buffer size value is 256, so change
the buffer size attribute type to U16 to configure the testbed
device to use the 256 buffer size in ADDBA negotiation in 11ax
testing.
This attribute is used only to configure a testbed device and the old
definition of this attribute was not used in any deployed implementation
hence it is still justifiable to change the definition.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a QCA vendor attribute
QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_BLACKLIST_BSSID to get maximum
blacklist BSSIDs capability from the driver for gscan.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new test config QCA vendor attribute to override the MU EDCA
parameters to default values in the driver for test configuration. This
is used for configuring the testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure HE
trigger frame MAC padding duration value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attributes to configure
HE MU EDCA parameters value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure Tx
beamformee number of space-time streams value in the driver.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit adds a new vendor command attribute
QCA_WLAN_VENDOR_ATTR_CONFIG_GTX in
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION to enable/disable green
Tx power saving feature.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add NAN attributes to communicate IPv6 address, port, and protocol
between wifihal and host driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Over time a number of style issues have crept into qca-vendor.h,
so fix most of them. There are some identifiers and comments which
exceed 80 columns, but these are left as-is for readability.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This can be used to determine which mechanism to use for configuring
country code from trusted sources.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure Tx
beamformee in the driver. This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add commands to allow an AP to configure filtering rules to capture
frames from stations that are active on the operating channel, but
not associated to this AP. Operations include add/delete the filter
and get the statistics information of the unassociated stations.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Add a new wifi test config attribute to configure HE LTF in the
driver. This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new WiFi test configuration attributes in QCA vendor
command to configure BA session parameters and to add or
delete a BA session and to configure no ack policy.
This is used for configuring the testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new WiFi test configuration attribute in QCA vendor
command to allow or not to allow WEP/TKIP in HT/VHT/HE mode.
This is used for configuring the testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enhance QCA vendor specific APF interface to support write/read program
and/or data and to enable/disable APF feature.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define a new QCA vendor sub command for configuring the device with wifi
test configuration. Add new test config attributes for this sub command
that are used to configure the device for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add new QCA vendor commands and attributes to get thermal information
and send thermal shutdown related commands. Indicates the driver to
enter the power saving mode or resume from the power saving mode based
on the given temperature and thresholds.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add additional NDP attributes and NDP subcommand value which is
provided as part of schedule update indication from driver/firmware
to HAL.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allow MSDU queue depth threshold in target to be set per peer per
TID. This command contains MAC address, TID, update mask, and threshold
values.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit extends the existing QCA vendor specific NUD_STATS_GET/SET
interface to also collect the statistics of the data packets. The
intention here is to get more comprehensive information to detect the
network unreachability.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
