Commit graph

991 commits

Author SHA1 Message Date
Jouni Malinen
c7f35a9e96 tests: Make scan_for_auth more robust
It was apparently possible for this test case not to do what it was
supposed to do, i.e., get nl80211 Authenticate command failing due to
cfg80211 BS entry missing. With the external radio work blocking fixed,
this can be cleaned up by explicitly waiting for the scan event. In
addition, a less used channel can be selected to avoid finding other BSS
entries.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-01 20:17:08 +02:00
Jouni Malinen
243dcc4ae4 tests: Add a helper function for clearing scan cache
This makes it more convenient and consistent to clear the cached scan
results from cfg80211 and wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-01 12:20:53 +02:00
Jouni Malinen
6ef319f4ea tests: AddressSanitizer (ASan) build options
Add example build options that can be used to enable ASan for hwsim test
cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Jouni Malinen
faa907389b tests: Stop connection at the end of monitor_iface_unknown_sta
Do not leave the station trying to connect at the end of the test case
since that can have an effect to the following test case. Such sequences
should be tested in test cases that are specifically designed for that
rather than randomly between test cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Jouni Malinen
ee27f6737b tests: Increase WEXT coverage
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 01:05:44 +02:00
Jouni Malinen
dc4c3dc4a2 tests: Simplify Michael MIC test file writing
Since run-tests.py is now required to run as root, there is no need to
use the somewhat awkward "sudo tee" construction; instead, just write
directly to the file.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 01:05:39 +02:00
Jouni Malinen
ae13ad6413 tests: Make go_neg_with_bss_on_disallowed_chan more robust
Clear scan results to avoid PBC overlap issues caused by earlier test
cases. For example, go_neg_with_bss_connected followed by
go_neg_with_bss_on_disallowed_chan resulted in failure before this
change.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-29 15:22:43 +02:00
Jouni Malinen
8969bad521 tests: Monitor interface with hostapd
This increases testing coverage for nl80211 AP mode with monitor
interface.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-29 13:33:50 +02:00
Jouni Malinen
73a2f82887 tests: Increase retry limit and timeout for wpas_mesh_open_no_auto
This test case was failing every now and then due to dev1
(no_auto_peer=1) not receiving the new-peer-candidate event in time
before dev0 has already stopped retries on mesh peering open message.
This sounds somewhat expected with the default 4 * 40 ms = 160 ms
retries and 1000 TU beacon interval. Use maximum timeout 16 * 255 ms =
4080 ms to make this test case less likely to fail.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:30 +02:00
Jouni Malinen
d9fee38658 tests: P2P invitation resend on no-common-channels
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:30 +02:00
Jouni Malinen
cff6eed75b tests: Re-enable wext_open
driver_wext.c is again able to configure open network, so re-enable the
test case for it.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:30 +02:00
Johannes Berg
b67cdbc162 tests: Allow wext in configuration
Both the wpa_supplicant and kernel configuration need wext to
run the wext testcase, enable those in the default/example
configurations.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-28 23:02:29 +02:00
Jouni Malinen
ee3f9f3837 tests: Optimize autogo test cases by removing unnecessary scans
Keep full channel scans in autogo for test coverage, but use single
channel scan in all other autogo* test cases to remove unnecessary
waiting that does not add any test coverage. This removes more than one
minute from the total test execution time.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:29 +02:00
Jouni Malinen
5a631ad2c2 tests: Optimize ap_open_unexpected_assoc_event
Replace fixed sleep with waiting for a disconnection event. In addition,
remove unnecessary use of sudo.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:29 +02:00
Jouni Malinen
2005cb87e5 tests: Hide unnecessary wlantest_cli output
Unnecessary and confusing "OK" output from wlantest_cli got sent to
stdout.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:29 +02:00
Jouni Malinen
e4d7b5134e tests: Move hessid and access_network_type reset to test case
This removes unnecessary reset() steps from between every test case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:29 +02:00
Jouni Malinen
47dcb1186f tests: Move external_sim reset to test cases that change this
This removes unnecessary reset() step from between every test case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:29 +02:00
Jouni Malinen
a0559aa5ba tests: Make go_neg_forced_freq_diff_than_bss_freq more robust
It was possible for this test case to fail due to PBC overlap that was
detected based on previous test case having used PBC. Make that false
positive less likely to happen by explicitly clearing the scan cache on
the device.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:29 +02:00
Jouni Malinen
6ea5e19898 tests: Fix p2p_channel_random_social_with_op_class_change cleanup
p2p_oper_reg_class and p2p_oper_channel need to be restored to 0, not an
arbitrary 2.4 GHz channel to avoid issues for following test cases. For
example, p2p_channel_random_social_with_op_class_change followed by
p2p_autogo_pref_chan_not_in_regulatory ended up with the latter test
case failing.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:29 +02:00
Jouni Malinen
4b57af2aaa tests: Remove duplicated connectivity test from mesh
hwsim_utils.test_connectivity() is already bidirectional test, so there
is no need to run it twice with the devices swapped for the second
iteration.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:29 +02:00
Jouni Malinen
882f894831 tests: Make hidden SSID test cases more robust
Clear wpa_supplicant and cfg80211 scan results at the end of hidden SSID
test cases to avoid potential issues for following test cases. For
example, ap_hs20_session_info could fail if executed immediately after
ssid_hidden due to the AP configuration change from open to RSN was not
noticed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:29 +02:00
Jouni Malinen
a712282bc1 tests: proxyarp with DHCP snooping
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 23:02:29 +02:00
Jouni Malinen
356a497d39 tests: ProxyARP with DGAF disabled and multicast-to-unicast conversion
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 22:41:26 +02:00
Jouni Malinen
67aeee118a tests: Convert proxyarp tests to use DATA_TEST_FRAME
This is more robust and extensible than configuring IPv6 addresses on
the interfaces and trying to use ping6 or some other external tools to
generate suitable IPv6 frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-28 20:00:14 +02:00
Jouni Malinen
54fe526ac4 tests: Make p2p_messages tests more robust under load
The 50 ms wait time for Action frame response was not sufficient when
the tests are run under heavy load (e.g., multiple VMs in parallel).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 21:44:01 +02:00
Jouni Malinen
0e02a557d3 tests: Make p2p_msg_invitation_req_to_go more robust
Wait for GO to start before sending invitation frames in the protocol
test. Without this, it was possible to hit the 5 second timeout on
management frame RX under load.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 21:22:31 +02:00
Jouni Malinen
4d7cc3961f tests: Make go_neg_with_bss_connected more robust
It was possible for this test case to fail due to PBC overlap that was
detected based on previous test case having used PBC. Make that false
positive less likely to happen by explicitly clearing the scan cache on
the devices.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 21:06:18 +02:00
Jouni Malinen
3c086180c1 tests: Make ap_wps_reg_config_tkip failure log more helpful
The "Not fully connected" report did not clearly identify what went
wrong, so make this more verbose in hope of being able to determine what
happened should this test case fail again.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 20:33:35 +02:00
Jouni Malinen
9ed53f5edf tests: Increase WPS connection timeout to make tests more robust
It was possible to hit the 10 second timeout in some test cases under
heavy load (e.g., with large number of VMs running tests in parallel).
These timeouts are not really indicating any real error, so make them
less likely to show up in reports by increasing the connection timeout
to 30 seconds.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 20:30:07 +02:00
Johannes Berg
6bb9d861f9 tests: Ignore status responses without =
There are valid status (and possibly status-driver) responses
that don't have a name=value format, ignore those in the test
framework parser.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-27 20:15:51 +02:00
Jouni Malinen
9363f5e065 tests: Optimize run-tests.py --prefill-tests startup time
It took significant part of the startup latency to prefill the database
with test cases due to the SQL COMMIT operation between each added row.
Move COMMIT to outside the loop to speed startup significantly.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 20:08:15 +02:00
Jouni Malinen
499c5e9dc6 tests: Follow test sequence from run-tests.py command line
It can be useful to specify an exact order of test cases and also to
allow the same test case to be run multiple times when the list of tests
is provided on the command line.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 19:48:41 +02:00
Johannes Berg
7ee6ec7aec tests: Create new radios for MCC tests
For tests that require a radio with multi-channel concurrency,
create a new one on the fly that does have more than 1 channel.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-27 18:25:25 +02:00
Johannes Berg
788dc17f8c tests: Use tshark -Y instead of tshark -R
Newer versions of tshark don't like the -R (read filter) argument
for filtering and just show a deprecation warning. Use -Y (display
filter) instead, which hopefully also works on older versions.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-27 18:24:26 +02:00
Jouni Malinen
1131a1c8d2 tests: Replace last remaining hwsim_test uses with DATA_TEST
External tool is not needed anymore to run the data connectivity tests
since hostapd test mode now allows the possible bridge or VLAN interface
to be specified.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 14:09:07 +02:00
Jouni Malinen
5f7b07de91 tests: ProxyARP
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-26 01:37:54 +02:00
Jouni Malinen
17ffdf3951 tests: Clear sae_groups to default value in forgotten cases
It was possible for some of the SAE test cases (e.g., ap_ft_sae) to fail
if they were run after the sae_groups test case that left the SAE group
configuration to a value that is not enabled by default. Fix this by
clearing sae_groups setting in the couple of test cases that were not
yet doing this.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-25 15:19:19 +02:00
Jouni Malinen
7c8f5ea6a0 tests: WPA2-PSK with RADIUS for passphrase
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-25 01:28:34 +02:00
Jouni Malinen
df4733dff9 tests: WNM BSS TM Req with non-global operating class table
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-24 10:58:33 +02:00
Jouni Malinen
986ed3a9ca tests: NEIGHBOR_REP_REQUEST failure cases
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 21:49:45 +02:00
Jouni Malinen
13f8d51e2d tests: BSS Transition Management
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 20:17:47 +02:00
Jouni Malinen
73360424d9 tests: Fix a typo in function name
except_ack() was supposed to be verifying that the frame was ACK'ed,
i.e., it was really supposed to be called expect_ack().

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 18:40:03 +02:00
Jouni Malinen
ab4ee34306 tests: Fix wnm_bss_tm_req status code expectation
The implementation of WNM BSS transition management was extended to be
able to return a reject status code based on whether a matching entry is
found. The test case wnm_bss_tm_req was trying to enforce a different
status code to be used here based on old implementation.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 18:40:03 +02:00
Jouni Malinen
64d04af5cc tests: Authenticator processing for various EAPOL-Key key info values
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-22 00:49:25 +02:00
Jouni Malinen
a52fd1c338 tests: WPA EAPOL 4-way handshake protocol testing
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-22 00:34:20 +02:00
Jouni Malinen
53b9bedb7a tests: WPA2 EAPOL-Key with incorrect type
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-22 00:16:41 +02:00
Jouni Malinen
821490f55f tests: Authenticator 4-way handshake protocol testing
This implements minimal RSN 4-way handshake Supplicant in Python and
uses that to test hostapd Authenticator implementation in various
possible protocol sequencies.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-21 20:50:41 +02:00
Jason Mobarak
f54b926baa tests: Mesh HT mode
Change the mesh tests to check for the presence of HT in the scan
results.

[original implementation by Chun-Yeow Yeoh <yeohchunyeow@gmail.com>]
[some fixes by Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
2014-11-20 17:01:43 +02:00
Javier Lopez
68157c0674 tests: Add test_wpas_mesh test cases
This wpa_supplicant tests include basic tests for:

- Mesh scan
- Mesh group add/remove
- Mesh peer connected/disconnected
- Add/Set/Remove to test mesh mode network
- Open mesh connectivity test
- Secure mesh connectivity test
- no_auto_peer

Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
[no_auto_peer test by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
2014-11-20 16:31:12 +02:00
Jouni Malinen
f6d1c5d9f8 tests: Fix regression in START line total count
The previous changes to enable stdin control broke the previous case of
showing the total number of test cases in the START lines. Fix that by
using a separate variable for the total number of test casess instead of
using length of the list of remaining test cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-19 22:02:08 +02:00