Commit graph

4655 commits

Author SHA1 Message Date
Jouni Malinen
2bdc47a945 DPP: Allow PKEX own/peer MAC addresses to be overridden
This is for testing purposes to allow a test vector with specific values
to be generated.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-23 23:47:52 +02:00
Jouni Malinen
af4103e5e9 DPP: Provide peer_mac to PKEX Initiator through function argument
Avoid unnecessary direct write to a struct dpp_pkex member from outside
dpp.c.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-23 23:32:33 +02:00
Jouni Malinen
3ca4be1eaa DPP: Remove compiler warnings about signed/unsigned comparisons
These timestamp comparisons did not use matching signedness.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-23 20:31:12 +02:00
bhagavathi perumal s
cc79e06f00 hostapd: Add wpa_msg_ctrl() to report Probe Request frames from STA
This allows external applications to get event indication for Probe
Request frames. Extend ctrl iface cmd "ATTACH" to enable this event on
per-request basis. For example, user has to send ctrl iface cmd "ATTACH
probe_rx_events=1" to enable the Probe Request frame events.

Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
2017-11-23 20:12:34 +02:00
Jouni Malinen
0db637ca80 DPP: Fix number of Authentication Request retry cases
Previous implementation did not handle number of sequences correctly.
Make sure the iteration continues in both unicast and broadcast cases
until the five attempts have been made. In addition, improve timing by
checking 10 second time from the beginning of each iteration round and
not the last channel on which the Auth Req frame has been transmitted.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-23 13:08:45 +02:00
Jouni Malinen
921f5acd17 DPP: Take response wait time into account for init retries
Previously, the Authentication Request frame was retried after 2+10 = 12
seconds since the wait for the response was not accounted for. Substract
that wait from the 10 second wait time to start the retries more quickly
based on the 10 second timer described in the tech spec.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-23 00:42:20 +02:00
Jouni Malinen
248264c622 DPP: Stop Authentication Request attempts if no response after ACK
If unicast Authentication Request frame is used and the peer ACKs such a
frame, but does not reply within the two second limit, there is no need
to continue trying to retransmit the request frames since the peer was
found, but not responsive.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-23 00:22:13 +02:00
Jouni Malinen
e3a5882b3e DPP: Add SAE credential support to Configurator
The new conf={sta,ap}-{sae,psk-sae} parameter values can now be used to
specify that the legacy configuration object is for SAE.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-22 21:24:08 +02:00
Jouni Malinen
5dd745b738 DPP: Add akm=sae and akm=psk+sae support in Enrollee role
This allows DPP to be used for enrolling credentials for SAE networks in
addition to the legacy PSK (WPA-PSK) case. In addition, enable FT-PSK
and FT-SAE cases automatically.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-22 21:23:51 +02:00
Jouni Malinen
00d2d13db2 DPP: Retry PKEX Exchange Request frame up to five times
Retransmit the PKEX Exchange Request frame if no response from a peer is
received. This makes the exchange more robust since this frame is sent
to a broadcast address and has no link layer retries.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-22 15:54:35 +02:00
Jouni Malinen
4b8de0c929 DPP: Protocol testing for invalid Peer Discovery Req/Resp values
Extend dpp_test to allow more invalid attribute values to be written
into Peer Discovery Request/Response frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-19 17:15:02 +02:00
Jouni Malinen
f9cf7d03f1 DPP: Protocol testing for invalid Config Attrib Object value
Extend dpp_test to cover a case where Config Attrib Object value is
invalid in Configuration Request frame.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-19 14:13:20 +02:00
Jouni Malinen
95b0104a34 DPP: Retransmit DPP Authentication Response frame if it is not ACKed
This extends wpa_supplicant DPP implementation to retransmit DPP
Authentication Response frame every 10 seconds up to 5 times if the peer
does not reply with DPP Authentication Confirm frame.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-13 12:35:26 +02:00
Jouni Malinen
c1d3773967 DPP: Stop authentication exchange of DPP_STOP_LISTEN
Previously, this command stopped listen operation immediately, but if
there was an ongoing authentication exchange, a new listen operation was
started. This is not really expected behavior, so stop the
authentication exchange first with this command to avoid restarting
listen operation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-13 12:35:26 +02:00
Jouni Malinen
d1f082644c DPP: Allowed initiator to indicate either role
The new role=either parameter can now be used with DPP_AUTH_INIT to
indicate that the initiator can take either the Configurator or Enrollee
role.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-13 11:45:05 +02:00
Jouni Malinen
f97ace34cb DPP: Support multiple channels for initiating DPP Authentication
This extends wpa_supplicant to iterate over all available channels from
the intersection of what the peer indicates and the local device
supports when initiating DPP Authentication. In addition, retry DPP
Authentication Request frame up to five times if no response is
received.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-13 11:45:05 +02:00
Jouni Malinen
de02986189 DPP: Share a helper function for PKEX final steps
Generate the PKEX bootstrapping information and release the PKEX session
in a helper function that both the initiator and responder can use
instead of maintaining this functionality separately in two places.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-13 10:30:11 +02:00
Jouni Malinen
a306ed5a58 DPP: Protocol testing to allow missing attributes in peer discovery
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-06 12:40:18 +02:00
Sunil Dutt
37ed3254de P2P: ACS offload for the autonomous GO
This commit introduces the ACS functionality for the autonomous GO. The
optional parameter <freq> in p2p_group_add is enhanced to carry a value
"acs" with the intention to select the channels among any supported
band. freq = 2 / 5 carry the need to select the channels only in the
respective bands 2.4 / 5 GHz. This functionality is on top of the host
driver's capability to offload ACS, which is advertized through
WPA_DRIVER_FLAGS_ACS_OFFLOAD.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-03 21:47:32 +02:00
Jouni Malinen
29ab69e4b0 DPP: PKEX counter t
Add limit on number of failed attempts that could have used PKEX code.
If the limit (5) is reached, drop the PKEX state (including the code)
and report this on the control interface to indicate that a new code
needs to be entered due to possible attack.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-03 19:59:46 +02:00
Jouni Malinen
039b8e7369 DPP: Terminate PKEX exchange on detection of a mismatching code
Clean up the pending PKEX exchange if Commit-Reveal Request processing
indicates a mismatch in the PKEX code. Previously, the this case was
silently ignored and the session was left in pending state that
prevented new PKEX exchanges from getting initated. Now, a new attempt
is allowed to be initiated.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-03 19:59:46 +02:00
Jouni Malinen
e0247e7983 DPP: PKEX and STATUS_BAD_GROUP
Report mismatching finite cyclic group with PKEX Exchange Response using
STATUS_BAD_GROUP and provide more detailed error report over the control
interface on the peer device when this happens.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-03 19:59:46 +02:00
Jouni Malinen
219d4c9fcb DPP: Report possible PKEX code mismatch in control interface
Indicate to upper layers if PKEX Commit-Reveal Request frame AES-SIV
decryption fails. That is a likely sign of the PKEX code mismatch
between the devices.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-02 12:25:35 +02:00
Jouni Malinen
69d8d029f5 DPP: Enable PMF when adding wpa_supplicant network profile
DPP AKM should really require PMF to be used, but since that is not yet
explicitly required in the specification, make PMF enabled for now. For
legacy PSK cases, configure PMF to be enabled as well to support both
APs in no-PMF, optional-PMF, and required-PMF configuration.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-11-01 17:14:30 +02:00
Jouni Malinen
d270920692 DPP: Negotiation channel change request from Initiator
Allow the Initiator to request a different channel to be used for DPP
Authentication and DPP Configuration exchanges. This commit adds support
for this in wpa_supplicant with the optional neg_freq=<freq in MHz>
parameter in DPP_AUTH_INIT.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-29 16:08:02 +02:00
Jouni Malinen
b7dddab7be DPP: Allow testing override values to be cleared
This allows wpa_supplicant dpp_config_obj_override,
dpp_discovery_override, and dpp_groups_override parameters to be cleared
by setting them to a zero-length value.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-29 12:23:34 +02:00
Jouni Malinen
e85b660129 DPP: Add DPP Status attribute into Peer Discovery Response
This was added in DPP tech spec v0.2.7 to allow result of network
introduction to be reported.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-29 12:16:15 +02:00
Jouni Malinen
26806abe85 DPP: Report invalid messages and failure conditions in control interface
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-22 22:45:17 +03:00
Jouni Malinen
af48810ba3 DPP: Report transmitted messages as control interface events
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Both the DPP-TX and DPP-TX-STATUS events are provided.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-22 17:21:57 +03:00
Jouni Malinen
a707393494 DPP: Report received messages as control interface events
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-22 17:21:57 +03:00
Jouni Malinen
27fefbbb76 DPP: Remove unnecessary Wrapped Data checks from callers
Now that dpp_check_attrs() takes care of verifying that no attributes
are after the Wrapped Data attribute, the duplicated checks in hostapd
and wpa_supplicant side of the implementation can be removed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-22 17:21:57 +03:00
Jouni Malinen
60239f60a6 DPP: Protocol testing framework
Add a generic mechanism for configuring the DPP implementation to behave
in particular different (mostly incorrect) ways for protocol testing
purposes. The new dpp_test parameter can be set to a non-zero integer to
indicate a specific behavior. This is only available in
CONFIG_TESTING_OPTIONS=y builds.

This commit include cases for an extra attribute being added after the
Wrapped Data attribute and Initiator/Responder capabilities having an
unexpected zero capability.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-22 17:21:57 +03:00
Jouni Malinen
7ed5337d8c Fix a typo in a debug message
This radio_work_free() message was missing the closing parenthesis.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-22 17:21:57 +03:00
Janusz Dziedzic
de41b960b6 wpa_supplicant: Increase UDP control interface RX buffer
Seems like some test cases, e.g., ap_wpa2_psk_ext_retry_msg_3c, require
larger buffer than 256 bytes.

In other case I fail such test cases when run on real HW and using:
CONFIG_CTRL_IFACE=udp-remote

Increase the RX buffer from 256 to 4096 bytes to match the other control
interface cases.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
2017-10-21 12:00:57 +03:00
Jouni Malinen
4be5bc98a8 DPP: Update AES-SIV AD for PKEX frames
The protocol design was updated to protect the six octets in the header
before the attributes.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-19 18:32:16 +03:00
Jouni Malinen
dc4d271c6d DPP: Update AES-SIV AD for DPP Authentication frames
The protocol design was updated to protect the six octets in the header
before the attributes.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-18 22:51:30 +03:00
Vidyullatha Kanchanapally
6338c99efa FILS: Send updated connection parameters to drivers if needed
After an initial connection wpa_supplicant derives ERP information which
can be used in doing eventual authentications in the same realm. This
information can be used by drivers with offloaded FILS support to do
driver/firmware initiated roamings. Add support to send this updated
information to such drivers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-18 01:19:42 +03:00
Vidyullatha Kanchanapally
d2ba0d719e Move assoc param setting into a helper function
This is needed to be able to use the same implementation for updating
the connection parameters in the driver during an association.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-18 01:19:42 +03:00
Vidyullatha Kanchanapally
b0a21e228d FILS: Update replay counter from roam info
Update the replay counter after a roam for all cases. This restores the
design back to what it was before commit
01ef320f19 ('FILS: Update ERP next
sequence number with driver offload').

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-17 16:26:44 +03:00
Jouni Malinen
daa4096084 Allow last (Re)Association Request frame to be replayed for testing
The new wpa_supplicant RESEND_ASSOC command can be used to request the
last (Re)Association Request frame to be sent to the AP to test FT
protocol behavior.

This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 17:47:24 +03:00
Jouni Malinen
751f5b2933 Allow EAPOL-Key Request to be sent through control interface
The new wpa_supplicant "KEY_REQUEST <error=0/1> <pairwise=0/1>" command
can be used to request an EAPOL-Key Request frame to be sent to the AP.

This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 17:47:24 +03:00
Jouni Malinen
bb06748f45 Make last received ANonce available through control interface
This makes it easier to debug 4-way handshake implementation issues
without having to use a sniffer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 17:47:24 +03:00
Jouni Malinen
16579769ff Add testing functionality for resetting PN/IPN for configured keys
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").

This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 17:43:10 +03:00
Jouni Malinen
a0bf1b68c0 Remove all PeerKey functionality
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.

This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.

Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 02:03:47 +03:00
Jouni Malinen
adae51f8b9 WNM: Ignore WNM-Sleep Mode Response without pending request
Commit 03ed0a5239 ('WNM: Ignore WNM-Sleep
Mode Response if WNM-Sleep Mode has not been used') started ignoring the
response when no WNM-Sleep Mode Request had been used during the
association. This can be made tighter by clearing the used flag when
successfully processing a response. This adds an additional layer of
protection against unexpected retransmissions of the response frame.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 02:03:47 +03:00
Jouni Malinen
a34ca59e4d SAE: Allow SAE password to be configured separately (STA)
The new sae_password network profile parameter can now be used to set
the SAE password instead of the previously used psk parameter. This
allows shorter than 8 characters and longer than 63 characters long
passwords to be used.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-11 23:24:19 +03:00
Sunil Dutt
c5aeb4343e P2P: Do not mark DFS channel as invalid if DFS is offloaded to driver
While considering the movement of P2P GO from its current operating
channel, do not mark a DFS channel as invalid if DFS is offloaded
to the driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-11 22:36:48 +03:00
Sunil Dutt
f516090228 P2P: Prefer 5/60 GHz band over 2.4 GHz during GO configuration
Previously, wpas_p2p_select_go_freq_no_pref() ended up selecting a 2.4
GHz band channel first before even considering 5 or 60 GHz channels.
This was likely done more or less by accident rather than by design when
the 5 GHz and 60 GHz band extensions were added. It seems reasonable to
enhance this by reordering the code to start with 5 and 60 GHz operating
classes and move to 2.4 GHz band only if no channel was available in 5
or 60 GHz bands for P2P GO use.

This does have some potential interop issues with 2.4 GHz only peer
devices when starting up an autonomous GO (i.e., without there being
prior knowledge of channels that the peers support). Upper layers are
expected to enforce 2.4 GHz selection if that is needed for some use
cases.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-11 17:01:10 +03:00
Jouni Malinen
265bda3444 OWE: Allow DH Parameters element to be overridden for testing purposes
This allows CONFIG_TESTING_OPTIONS=y builds of wpa_supplicant to
override the OWE DH Parameters element in (Re)Association Request frames
with arbitrary data specified with the "VENDOR_ELEM_ADD 13 <IE>"
command. This is only for testing purposes.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-10 18:26:29 +03:00
Jouni Malinen
8c19ea3f21 DPP: Add the crypto suite field to the frames
This additional field was added to DPP Public Action frames in DPP tech
spec v0.2.3 to support cryptographic agility in the future.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-10 01:30:08 +03:00
Jouni Malinen
c77e2ff096 DPP: Remove C-sign-key expiry
This was removed in DPP tech spec v0.2.3.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-10 01:17:33 +03:00
Jouni Malinen
109704657d OWE: Support station SME-in-driver case
Previously, only the SME-in-wpa_supplicant case was supported. This
extends that to cover the drivers that implement SME internally (e.g.,
through the cfg80211 Connect command).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-09 12:35:14 +03:00
Jouni Malinen
5a78c36194 OWE: PMKSA caching in station mode
This extends OWE support in wpa_supplicant to allow PMKSA caching to be
used.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-09 12:12:54 +03:00
Jouni Malinen
ec9f483774 OWE: Support DH groups 20 (NIST P-384) and 21 (NIST P-521) in station
This extends OWE support in wpa_supplicant to allow DH groups 20 and 21
to be used in addition to the mandatory group 19 (NIST P-256). The group
is configured using the new network profile parameter owe_group.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-08 17:12:35 +03:00
Jouni Malinen
7a12edd163 OWE: Support DH groups 20 (NIST P-384) and 21 (NIST P-521) in AP mode
This extends OWE support in hostapd to allow DH groups 20 and 21 to be
used in addition to the mandatory group 19 (NIST P-256).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-08 17:12:35 +03:00
Jouni Malinen
e8b9649012 OWE: Transition mode support on station side
Add support for using the OWE Transition Mode element to determine the
hidden SSID for an OWE BSS that is used in transition mode.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-08 17:12:35 +03:00
Jouni Malinen
675112df1b OWE: Set PMK length properly on supplicant side
sm->pmk_len was not set when deriving the PMK as part of OWE key
generation. This depending on wpa_sm_set_pmk_from_pmksa() call resetting
the value to the default. While this worked for many cases, this is not
correct and can have issues with network profile selection based on
association information. For example, the OWE transition mode cases
would hit an issue here.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-08 17:12:35 +03:00
Sunil Dutt
63bc0ab0ed P2P: Allow GO to advertise Interworking element
This adds new wpa_supplicant configuration parameters (go_interworking,
go_access_network_type, go_internet, go_venue_group, go_venue_type) to
add a possibility of configuring the P2P GO to advertise Interworking
element.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-05 14:42:16 +03:00
vamsi krishna
e37cea308e OCE: Update default scan IEs when OCE is enabled/disabled
Update the default scan IEs when OCE is enabled/disabled to the
driver/firmware, so that the correct IEs will be sent out by the
driver/firmware in Probe Request frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-01 18:47:02 +03:00
Jouni Malinen
61a56c1480 Add group_mgmt network parameter for PMF cipher selection
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-26 17:40:02 +03:00
Jouni Malinen
60ed2f24eb Suite B: Add tls_suiteb=1 parameter for RSA 3k key case
This adds phase1 parameter tls_suiteb=1 into wpa_supplicant
configuration to allow TLS library (only OpenSSL supported for now) to
use Suite B 192-bit level rules with RSA when using >= 3k (3072) keys.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-17 00:09:47 +03:00
Jouni Malinen
5030d7d9fd DPP: Allow raw hex PSK to be used for legacy configuration
The new psk=<hexdump> can be used as an alternative to pass=<passphrase>
when configuring the DPP Configurator with a legacy network parameters.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-15 17:54:31 +03:00
Lior David
3c7863f812 wpa_supplicant: Support dynamic update of wowlan_triggers
Previously, wowlan_triggers were updated in kernel only during startup.
Also update it whenever it is set from the control interface.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-13 22:17:58 +03:00
Lior David
3031133983 mesh: Move writing of mesh_rssi_threshold inside CONFIG_MESH
Previously, the code that writes mesh_rssi_threshold to a network block
always executes, but the code that reads it from network block and the
code that initializes it to a default value in a new network block are
inside #ifdef CONFIG_MESH. As a result when writing a config file it
will write mesh_rssi_threshold (since it has a non-default value) and
later fail to read the network block.

Fix this by moving the write code under #ifdef CONFIG_MESH as well.
Note, network blocks which already have mesh_rssi_threshold because of
the bug will still fail to read after the fix.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2017-09-12 17:17:21 +03:00
Jouni Malinen
2efc672075 Fix RSN pre-authentication regression with pre-connection scan results
The introduction of radio works and a delayed callback to complete
association/connection requests ended up breaking RSN pre-authentication
candidate list generation for the case of pre-connection scan results.
Previously, wpa_supplicant_associate() set the RSN state machine
configuration before returning and the calls to
wpa_supplicant_rsn_preauth_scan_results() immediately after this
function call were working fine. However, with the radio work callback,
the RSN state machine configuration started to happen only in that
callback which would be called soon after this code path has completed.
This resulted in the RSN state machine not knowing the selected SSID and
as such, rejecting all pre-authentication candidates.

Fix this by setting the RSN state machine configuration from
wpa_supplicant_associate() so that the existing callers of
wpa_supplicant_rsn_preauth_scan_results() can be used as-is to add
candidates for pre-authentication.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-12 16:47:02 +03:00
Sabrina Dubroca
7612e65b9b mka: Add error handling for secy_init_macsec() calls
secy_init_macsec() can fail (if ->macsec_init fails), and
ieee802_1x_kay_init() should handle this and not let MKA run any
further, because nothing is going to work anyway.

On failure, ieee802_1x_kay_init() must deinit its kay, which will free
kay->ctx, so ieee802_1x_kay_init callers (only ieee802_1x_alloc_kay_sm)
must not do it. Before this patch there is a double-free of the ctx
argument when ieee802_1x_kay_deinit() was called.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2017-09-10 22:23:25 +03:00
Adiel Aloni
2c66c7d115 wpa_supplicant: Check length when building ext_capability in assoc_cb
When building wpa_ie in wpas_start_assoc_cb() with ext_capab,
make sure that assignment does not exceed max_wpa_ie_len.

Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
2017-09-10 22:16:06 +03:00
Saurav Babu
cdf2501494 dbus: Add new interface property to get mesh group
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-10 01:39:37 +03:00
Saurav Babu
190f6f1176 dbus: Add new interface property to get connected mesh peers
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-10 01:39:37 +03:00
Saurav Babu
a9de99b1c5 dbus: Add MeshPeerDisconnected signal
This is similar to the control interface event MESH-PEER-DISCONNECTED.

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-10 01:39:37 +03:00
Saurav Babu
9b0701fbf5 dbus: Add MeshPeerConnected signal
This is similar to the control interface event MESH-PEER-CONNECTED.

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-10 01:39:35 +03:00
Saurav Babu
a39b040b4c dbus: Add MeshGroupRemoved signal
This is similar to the control interface event MESH-GROUP-REMOVED.

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-09 14:12:33 +03:00
Saurav Babu
89e9cd25d2 dbus: Add MeshGroupStarted signal
This introduces a new interface for mesh and adds a signal that
is similar to the control interface event MESH-GROUP-STARTED.

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-09 14:01:14 +03:00
Jouni Malinen
a0f19e9c74 SAE: Allow commit fields to be overridden for testing purposes (STA)
The new "SET sae_commit_override <hexdump>" control interface command
can be used to force wpa_supplicant to override SAE commit message
fields for testing purposes. This is included only in
CONFIG_TESTING_OPTIONS=y builds.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-04 13:32:03 +03:00
Jouni Malinen
a6f238f217 DPP: Add base64 dependency in makefiles
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-09-04 13:31:21 +03:00
Jouni Malinen
85fd8263a5 DPP: Use Transaction ID in Peer Discovery Request/Response frames
DPP tech spec changed the contents of these frames by replacing the
public key hash attributes with a Transaction ID attribute that gets
copied from the request to the response to identify the transaction in a
simpler manner.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-08-23 12:51:41 +03:00
Jouni Malinen
a4bf007877 DPP: Remove devices object from the connector
This was removed from the draft DPP tech spec, so remove it from the
implementation as well.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-08-22 23:46:27 +03:00
Avraham Stern
b5bf84ba39 WNM: Differentiate between WNM for station and for AP in build
Previously, CONFIG_WNM enabled build that supports WNM for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode WNM is required and there is no need for AP mode WNM.

Add support to differentiate between station mode WNM and AP mode
WNM in wpa_supplicant builds by adding CONFIG_WNM_AP that should be
used when AP mode WNM support is required in addition to station mode
WNM. This allows binary size to be reduced for builds that require
only the station side WNM functionality.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-07-18 13:28:09 +03:00
Avraham Stern
922dcf1b45 RRM: Remove duplicate frequencies from beacon report scan request
When setting the frequencies for beacon report request scan, it is
possible that a frequency is added twice (e.g., when the same channel
appears both in the channel field and in the AP channel report
subelement). This may cause the scan request to fail.
Make sure the frequencies array contains no duplications before
requesting the scan.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-07-17 18:04:34 +03:00
Avraham Stern
705e2909c6 RRM: Send response when Beacon report request is not supported/refused
Send Radio Measurement response with measurement mode set to reject
in the following cases:
 1. Reporting conditions is not supported.
 2. No valid channels found for the measurement

Sending a response with an incapable indication will stop the AP from
sending other measurement requests of the same type as specified
in IEEE Std 802.11-2016, 11.11.6.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-07-17 18:00:56 +03:00
Avraham Stern
3756acfd48 RRM: Send Radio Measurement response when beacon report scan fails
When failing to trigger scan for beacon report (e.g., when the
requested duration is not supported by the driver), send a
Radio Measurement response with the mode set to refused and don't
retry the scan.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-07-17 17:57:41 +03:00
Avraham Stern
b3c148e9f8 RRM: Send reject/refuse response only to unicast measurement request
IEEE Std 802.11-2016, 11.11.6 specifies that a station that is unable to
make a requested measurement or refuses to make a measurement shall
respond only if the measurement request was received within an
individually addressed radio measurement request frame, but shall not
respond if such a request was received in a group addressed frame.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-07-17 17:43:32 +03:00
Dmitry Shmidt
51143af7e7 wpa_cli: Fix global control interface for STA-FIRST/STA-NEXT
If global control interface is used and wlan doesn't support P2P,
   wpa_s->global->p2p == NULL, and log shows:
wpa_supplicant: Failed to create interface p2p-dev-wlan0: -5 (I/O error)
wpa_supplicant: nl80211: Failed to create a P2P Device interface p2p-dev-wlan0
wpa_supplicant: P2P: Failed to enable P2P Device interface

Then STA-FIRST/STA-NEXT is not going to redirect to any interface,
making update_stations(ctrl_conn) is stuck in never-ending loop:

sendto(3, "STA-FIRST", 9, 0, NULL, 0)   = 9
pselect6(4, [3], NULL, NULL, {10, 0}, NULL) = 1 (in [3], left {9, 999995000})
recvfrom(3, "UNKNOWN COMMAND\n", 4095, 0, NULL, NULL) = 16
sendto(3, "STA-NEXT UNKNOWN COMMAND", 24, 0, NULL, 0) = 24
pselect6(4, [3], NULL, NULL, {10, 0}, NULL) = 1 (in [3], left {9, 999995833})
recvfrom(3, "UNKNOWN COMMAND\n", 4095, 0, NULL, NULL) = 16
sendto(3, "STA-NEXT UNKNOWN COMMAND", 24, 0, NULL, 0) = 24
pselect6(4, [3], NULL, NULL, {10, 0}, NULL) = 1 (in [3], left {9, 999995000})
recvfrom(3, "UNKNOWN COMMAND\n", 4095, 0, NULL, NULL) = 16
sendto(3, "STA-NEXT UNKNOWN COMMAND", 24, 0, NULL, 0) = 24

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2017-07-17 14:54:42 +03:00
Beniamino Galvani
2b9891bd6e OpenSSL: Add build option to select default ciphers
Add a build option to select different default ciphers for OpenSSL
instead of the hardcoded default "DEFAULT:!EXP:!LOW".

This new option is useful on distributions where the security level
should be consistent for all applications, as in Fedora [1]. In such
cases the new configuration option would be set to "" or
"PROFILE=SYSTEM" to select the global crypto policy by default.

[1] https://fedoraproject.org/wiki/Changes/CryptoPolicy

Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
2017-07-17 11:55:22 +03:00
Ashwini Patil
332aadb8a2 STA: Add OCE capability indication attribute
Add OCE capability indication attribute in Probe Request and
(Re)Association Request frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-14 21:19:53 +03:00
Vidyullatha Kanchanapally
b377ec2585 FILS: Fix issuing FILS connect to a non-FILS AP in driver-FILS case
If an AP is not FILS capable and wpa_supplicant has a saved network
block for the network with FILS key management and a saved erp info,
wpa_supplicant might end up issuing a FILS connection to a non-FILS AP.
Fix this by looking for the presence of FILS AKMs in wpa_s->key_mgmt,
i.e., after deciding on the AKM suites to use for the current
connection.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-14 21:11:35 +03:00
Ilan Peer
422570eec8 MBO: Fix possible memory leak in anqp_send_req()
In case that an mbo object is allocated, but there is a failure
to resize the wpabuf, need to free the mbo object.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2017-07-08 16:14:03 +03:00
Avraham Stern
23eead4d74 RRM: Filter scan results by parent TSF only if driver supports it
Scan results with parent TSF older than the scan start TSF are not added
to the beacon report since they are considered as scan results from
previous scans. However, for drivers that report the scan start TSF but
not the parent TSF of each scan result, the parent TSF will be zero so
valid scan results will be dropped.

Fix this by filtering scan results by the parent TSF only if the
driver supports reporting the parent TSF for each scan result.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-07-08 16:06:38 +03:00
Andrei Otcheretianski
d02e4c8ac8 P2P: Clear get_pref_freq_list_override on P2P Device
Clear the get_pref_freq_list_override in p2p_ctrl_flush(). This fixes
the case when a dedicated P2P device interface is used.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2017-07-08 16:06:28 +03:00
Andrei Otcheretianski
bfbc41eace DPP: Fix compilation without openssl
dpp.h file requires openssl in order to compile, which breaks
compilation on systems without it.
Move DPP_OUI_TYPE to ieee802_11_defs.h and don't include dpp.h when
not really needed.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2017-07-07 23:37:45 +03:00
Sunil Dutt
cc6088463a P2P: Allow auto GO on DFS channels if driver supports this
If a DFS forced frequency is provided in 'p2p_group_add' and the driver
supports DFS offload, the frequency was rejected in
wpas_p2p_init_go_params(). However, it was accepted in
wpas_p2p_select_go_freq() and wpas_p2p_group_add(). To make the behavior
consistent, the DFS frequency is now accepted in
wpas_p2p_init_go_params() similar to the way done in
wpas_p2p_select_go_freq().

Redundant check in wpas_p2p_group_add() for DFS forced frequency is
removed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-07 13:49:01 +03:00
Vidyullatha Kanchanapally
fe3e0bac1f FILS: Advertize FILS capability based on driver capability
Add changes to control interface command get_capability to advertize
FILS capability, FILS AKMs suites, and FILS Authentication algorithms
based on the driver capabilities.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-07 13:39:05 +03:00
Jouni Malinen
6d49aeb762 MBO: Whitespace cleanup
Fix couple of previously missed whitespace issues.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-05 02:02:35 +03:00
Ashwini Patil
267fc0dd33 Add wpa_supplicant ctrl iface support to scan for a specific BSSID
Add support to scan for a specific BSSID through the wpa_supplicant
control interface.

Usage: wpa_cli scan bssid=ab:bc:cd🇩🇪ef:12

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-05 02:02:32 +03:00
Jouni Malinen
f522bb2377 DPP: Add DPP_CONFIGURATOR_SIGN to generate own connector
The DPP Configurator can use this new command to generate its own signed
connector for the network that it manages.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-04 17:48:44 +03:00
Jouni Malinen
484788b875 DPP: Share bootstrap type to string helper function
This can be used in hostapd as well.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-04 15:45:03 +03:00
Jouni Malinen
623f95685d DPP: Allow wpa_cli DPP_CONFIGURATOR_ADD without arguments
All the arguments to this command are optional, so do not mandate at
least one to be included in wpa_cli.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-04 15:38:52 +03:00
Jouni Malinen
787615b381 DPP: Set PMKSA expiration based on peer connector
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-03 13:29:59 +03:00
Jouni Malinen
b65b22d60a DPP: Configurator parameters in responder role
This allows wpa_supplicant to be configured to act as the configurator
in the case where a peer device initiates DPP Authentication.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-03 13:03:34 +03:00
Jouni Malinen
500ed7f006 DPP: PKEX bootstrapping
This implements genric PKEX functionality in src/common/dpp.c and glue
code to use this in wpa_supplicant (i.e, hostapd DPP implementation does
not yet support PKEX).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-02 09:35:00 +03:00
Jouni Malinen
44d6b272cf DPP: Fix configuration item list
This was supposed to use semicolons, not commas..

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-07-02 09:35:00 +03:00
Ashwini Patil
b04854ceff nl80211/MBO: Set temporary disallowed BSSID list to driver
Set temporary disallowed BSSID list to the driver so that the driver
doesn't try to connect to any of the blacklisted BSSIDs during
driver-based roaming operation. This commit includes support only for
the nl80211 driver interface using a QCA vendor command for this.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-30 17:27:44 +03:00
Jouni Malinen
35f064212c DPP: Allow passphrase to be set for Configurator
The new pass=<hexdump> parameter to DPP_AUTH_INIT can now be used to
specify the passphrase to use in config object.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-23 12:46:14 +03:00
Jouni Malinen
68cb6dcec1 DPP: Allow SSID to be set for Configurator
The new ssid=<hexdump> parameter to DPP_AUTH_INIT can now be used to
specify the SSID to use in config object.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-23 12:45:25 +03:00
Jouni Malinen
a82349347d DPP: Add an example python script for QR Code operations
This script can be used to process Android logcat information for
scanned QR Codes (e.g., from Barcode Scanner app) and also to display QR
Codes for locally generated bootstrap keys.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-22 14:52:28 +03:00
Jouni Malinen
6a7182a9c3 DPP: Add DPP_BOOTSTRAP_INFO command
This can be used to fetch parsed details on bootstrapping information.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-22 14:51:21 +03:00
Jouni Malinen
8528994e21 DPP: Automatic network profile creation
wpa_supplicant can now be configured to generate a network profile
automatically based on DPP configuration. The following
dpp_config_processing values can be used to specify the behavior:
0 = report received configuration to an external program for
    processing; do not generate any network profile internally (default)
1 = report received configuration to an external program and generate
    a network profile internally, but do not automatically connect
    to the created (disabled) profile; the network profile id is
    reported to external programs
2 = report received configuration to an external program, generate
    a network profile internally, try to connect to the created
    profile automatically

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-21 18:03:34 +03:00
Jouni Malinen
da143f7fb9 FILS: Fix EVENT_ASSOC processing checks for driver-SME
Commit 5538fc9309 ('FILS: Track completion
with FILS shared key authentication offload') added an additional case
for calling wpa_supplicant_event_assoc_auth() from EVENT_ASSOC handling
in case of FILS-completion with driver-based-SME. However, that checked
what placed outside the data != NULL case while data != NULL needs to
apply for this case as well due to wpa_supplicant_event_assoc_auth()
behavior. Move the data != NULL check to apply to both cases to avoid
potentially issues if a driver interface were to return EVENT_ASSOC
without the associate data. (CID 164708)

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 23:36:13 +03:00
Jouni Malinen
3c0daa13d5 Make wpa_config_read_blob() easier for static analyzers
While encoded == NULL could happen in the case of an empty blob, that
will result in encoded_len == 0 and base64_decode() not derefencing the
src argument. That seems to be too difficult for some static analyzers,
so to avoid false warnings, explicitly reject the encoded == NULL case
without even trying to base64 decode it. (CID 164709)

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:30:45 +03:00
Jouni Malinen
a0d5c56f8b DPP: Network Introduction protocol for wpa_supplicant
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:59 +03:00
Jouni Malinen
b979caae57 DPP: Network profile parameters for DPP AKM
Extend wpa_supplicant network profile to include parameters needed for
the DPP AKM: dpp_connector, dpp_netaccesskey, dpp_netaccesskey_expiry,
dpp_csign, dpp_csign_expiry.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Jouni Malinen
567da5bbd0 DPP: Add new AKM
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Jouni Malinen
9c2b8204e6 DPP: Integration for hostapd
This adds DPP bootstrapping, authentication, and configuration into
hostapd similarly to how the design was integrated in wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Jouni Malinen
9beb2892de DPP: Add wpa_cli commands for DPP operations
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Jouni Malinen
461d39af40 DPP: Configuration exchange
This adds support for DPP Configuration Protocol using GAS. Full
generation and processing of the configuration object is not included in
this commit.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:15 +03:00
Jouni Malinen
30d27b048e DPP: Authentication exchange
Add wpa_supplicant control interface commands for managing DPP
Authentication exchange.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:12:30 +03:00
Jouni Malinen
be27e185b7 DPP: Bootstrap information management
Add wpa_supplicant control interface commands for parsing the bootstrap
info URI from a QR Code (get peer public key) and to generate a new
bootstrap info with private key for local use. The optional
key=<hexdump> argument to the DPP_BOOTSTRAP_GEN command can be used to
specify the bootstrapping private key in OpenSSL ECPrivateKey DER
encoding format. This results in the local bootstrapping information
entry being created with the specified key instead of generating a new
random one.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 12:03:30 +03:00
Jouni Malinen
d4d76d9835 Fix offchannel TX done handling for sequence of TX frames
There could be multiple pending TX operations and if the earlier ones
have used wait_time, but the last one did not, the driver call for
canceling pending wait was not done. This could result in the driver
getting stuck waiting for the previously scheduled wait time and not
being able to do new operations until that. Fix this by canceling the
wait if any of the past offchannel_send_action() calls since the last
offchannel_send_action_done() used non-zero wait_time.

This was showing up as issues in certain DPP Public Action frame
sequences when the same offchannel operation is used with multiple
frames and the last frame in the sequence does not need wait_time.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-17 18:04:54 +03:00
Jouni Malinen
005be3daa9 Add JavaScript Object Notation (JSON) parser (RFC7159)
This is needed for DPP configuration attributes/objects.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-17 18:04:51 +03:00
Jouni Malinen
77f273c82c Extend SHA-384 and SHA-512 support to match SHA-256
The additional SHA-384 and SHA-512 functionality is needed to support
DPP with various ECC curves.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-17 18:04:12 +03:00
Jouni Malinen
2c9d924975 P2P: Debug print P2P_FIND rejection reason
This can be helpful in figuring out what happened if P2P_FIND operation
is unexpectedly rejected.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-13 14:50:51 +03:00
Wu Gao
618aa22900 P2P: Fix p2p_in_provisioning clearing in failure case
wpa_s->p2p_in_provisioning needs to be cleared when group formation
fully completes. The change to postpone GO side handling to the first
data connection in commit 41f853235f
('P2P: Extend group formation timeout on GO to first data connection')
resulted in making this not happen in one P2P Client side case: EAP-WSC
timeout in PBC case. While that is quite special case since it requires
30 second timeout without receiving new EAPOL frames and not getting
disassociation, it can apparently happen in some cases in practice. This
would result in new P2P operations (e.g., P2P_FIND) getting rejected
until wpa_supplicant is restarted.

Fix this by clearing wpa_s->p2p_in_provisioning whenever processing a
group formation failure case. For group formation success,
wpa_s->p2p_in_provisioning is left set to non-zero value to avoid
breaking the earlier limits on the GO side.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-13 14:49:36 +03:00
Vidyullatha Kanchanapally
b5db6e5dc4 eap_proxy: Support multiple SIMs in get_imsi()
This allows the eap_proxy mechanism to be used with multiple SIMs by
following the configured sim_num to index which SIM to use for when
fetching the IMSI through eap_proxy.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-06 03:42:32 +03:00
Sunil Dutt
3c2bd55f03 P2P: wpas_p2p_select_go_freq() to check for supported pref_freq
This commit is similar to the commit
783c2920cc ('P2P: Check if the pref_freq
reported by the driver supports P2P') but extends the check for
supported pref_freq to wpas_p2p_select_go_freq().

This avoids issues with P2P_GROUP_ADD ending up selecting an unexpected
channel when get_pref_freq_list() (i.e.,
QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST) is used. Filter the
list by removing channels that do not allow P2P operation at all.
Previously, only the explicitly disallowed channels were removed and
that could have resulted in selecting an operating channel that is not
allowed for P2P and failing to complete the operation to start the
group.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-27 11:41:02 +03:00
Peng Xu
8d968351a0 Interworking: Add NULL checking for EAP name in phase2/autheap parameter
Add NULL checking for EAP name. If it is NULL, do not add the phase2
parameter autheap. This should not happen in practice due to earlier
checks for credential matching, but if there is a code path that would
allow this to be set, it is better to skip setting of the invalid value
and allow automatic selection of the Phase 2 parameters.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-26 13:20:52 +03:00
Purushottam Kushwaha
34ee12c559 Do not flush PMKSA on bssid_hint change
Change in any network configuration at runtime will cause flush to
PMKSA cache. For most of the network parameters if there is no change
in value, PMKSA flush is not performed except 'bssid' and 'priority'.

Add 'bssid_hint' to exemption list of avoiding PMKSA flush on change.
This is needed to complete change in commit
43a356b268 ('Provide option to configure
BSSID hint for a network').

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-22 13:25:49 +03:00
Vasanthakumar Thiagarajan
aa56e36d66 driver: Make DFS domain information available to core
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
2017-05-13 20:01:44 +03:00
Purushottam Kushwaha
43a356b268 Provide option to configure BSSID hint for a network
This exposes user configurable option to set bssid_hint for a network.
bssid_hint indicates which BSS has been found a suitable candidate for
initial association for drivers that use driver/firmware-based BSS
selection. Unlike the bssid parameter, bssid_hint does not limit the
driver from selecting other BSSs in the ESS.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-12 00:20:59 +03:00
Jouni Malinen
95818ec174 Fix compiler warning with CONFIG_IEEE80211R no-CONFIG_FILS build
Addition of remove_ies() handled the CONFIG_IEEE80211R dependency, but
missed the caller being within CONFIG_FILS as well.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-09 23:36:36 +03:00
Jaap Keuter
6136394545 Make CONFIG_MACSEC depend on IEEE8021X_EAPOL
When reducing the configuration for MACsec/MKA to the bare minimum, so
no EAP authentication, just MACsec/MKA SA use with preshared key/name,
the EAPOL engine is still needed to run the protocol for MKA. Without
any EAP authentication options the IEEE8021X_EAPOL option is not set,
resulting in a non-working Key Agreement Entity.

Therefore the CONFIG_MACSEC block needs to move up and set the
IEEE8021X_EAPOL option.

Signed-off-by: Jaap Keuter <jaap.keuter@xs4all.nl>
2017-05-08 16:28:27 +03:00
Masashi Honma
31a856a127 mesh: Make NL80211_MESHCONF_RSSI_THRESHOLD configurable
In some practical cases, it is useful to suppress joining to node in the
distance. The new field mesh_rssi_threshold could be used as RSSI
threshold for joining.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-05-08 16:23:02 +03:00
Nishant Chaprana
9f49474669 dbus: Add method to disable channel switching with a TDLS peer
This patch adds "TDLSCancelChannelSwitch" dbus method on
"fi.w1.wpa_supplicant1.Interface" interface to disable channel switching
with a TDLS peer.

Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2017-05-07 22:08:43 +03:00
Nishant Chaprana
2a57b4b821 dbus: Add method to enable channel switching with a TDLS peer
This patch adds "TDLSChannelSwitch" dbus method on
"fi.w1.wpa_supplicant1.Interface" interface to enable channel switching
with a TDLS peer.

Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2017-05-07 22:08:43 +03:00
Saurav Babu
1939505419 dbus: Add AbortScan method to abort ongoing scan
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-05-07 22:08:43 +03:00
Jouni Malinen
7d440a3bc4 FILS: Derive FT key hierarchy on supplicant side for FILS+FT
Derive PMK-R0 and the relevant key names when using FILS authentication
for initial FT mobility domain association. Fill in the FT IEs in
(Re)Association Request frame for this.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-05-07 22:08:41 +03:00
Dmitry Shmidt
be1ece46f5 wpa_supplicant: Add GET_CAPABILITY for P2P redirection
It will give capability to check channel list before P2P group is
created.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2017-05-05 00:43:23 +03:00
Vamsi Krishna
35bb8a9a57 Android: Define CONFIG_TESTING_OPTIONS if enabled in config
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-05 00:26:06 +03:00
Vamsi Krishna
178553b709 MBO: Add support to set ignore assoc disallow to driver
Add support to set ignore assoc disallow to the driver so that the
driver ignores assoc disallowed bit set by APs while connecting. This is
used by drivers that handle BSS selection and roaming internally.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-05 00:26:05 +03:00
Pradeep Reddy Potteti
f2a04874cf MBO: Fix possible NULL pointer dereference on candidate handling
If the driver provides input on MBO transition candidate handling, the
target value in get_mbo_transition_candidate() can be NULL if the driver
provided BSSID is not found in the wpa_supplicant BSS table. And later
it would be dereferenced. Fix this by adding an explicit check before
dereferencing the pointer.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-03 18:30:31 +03:00
Jouni Malinen
470f08b4f6 Enable CONFIG_WNM=y automatically for CONFIG_MBO=y builds
wpa_supplicant build with MBO enabled failed in CONFIG_WNM=y was not
specified explicitly. Add the WNM dependency automatically to avoid
needing explicit addition in build configuration.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-05-01 17:39:14 +03:00
Jouni Malinen
8b49b530b3 Fix CONFIG_INTERWORKING=y build without CONFIG_HS20=y
Commit 34f2851902 ('MBO: Parse MBO
ANQP-element on STA') started using the type variable outside
CONFIG_HS20 block, but forgot to remove the ifdef from the variable
declaration.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-05-01 17:39:14 +03:00
Sunil Dutt
0661163eff Do not blacklist the current AP on DISABLE_NETWORK
Disconnection due to DISABLE_NETWORK while being connected was resulting
in the AP getting blacklisted. Avoid this by setting own_disconnect_req
on a disconnect request due to DISABLE_NETWORK similarly to the
SELECT_NETWORK disconnection case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-29 17:46:36 +03:00
Vidyullatha Kanchanapally
da6a28ba60 FILS: Specify if FILS HLP was sent in connect
This adds a string "FILS_HLP_SENT" to connect event when HLP is sent
as part of ASSOC/CONNECT request.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-29 16:35:23 +03:00
Vidyullatha Kanchanapally
a38090b16d FILS: Add HLP to Connect IEs
Add FILS HLP elements to Connect IEs and fragment them if necessary.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-29 16:35:21 +03:00
Vidyullatha Kanchanapally
1e6780bda9 Allocate dynamic memory for connect IEs
This is needed to allow new elements (e.g., FILS HLP request) to be
added.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-29 16:34:48 +03:00
Ashwini Patil
9a72bfe9a4 Add control interface command to enable/disable roaming
The new "SET roaming <0/1>" command can now be used to control
driver-based roaming.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-24 11:10:44 +03:00
Jouni Malinen
183d3924cf WPS: Add option for using random UUID
If the uuid configuration parameter is not set, wpa_supplicant generates
an UUID automatically to allow WPS operations to proceed. This was
previously always using an UUID generated from the MAC address. This
commit adds an option to use a random UUID instead. The type of the
automatically generated UUID is set with the auto_uuid parameter: 0 =
based on MAC address (default; old behavior), 1 = random UUID.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-13 17:38:55 +03:00
Vidyullatha Kanchanapally
bbe7969d63 FILS: Update cache identifier on association
This is needed when offloading FILS shared key to the drivers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:59:12 +03:00
Vidyullatha Kanchanapally
f705f41b7f FILS: Update PMKSA cache with FILS shared key offload
Add a new PMKSA cache entry within wpa_supplicant if a driver event from
offloaded FILS shared key authentication indicates a new PMKSA entry was
created.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
01ef320f19 FILS: Update ERP next sequence number with driver offload
This keeps the internal ERP information within wpa_supplicant in sync
with the driver when offloading FILS shared key authentication.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
5538fc9309 FILS: Track completion with FILS shared key authentication offload
Update the internal fils_completed state when offloading FILS shared key
authentication to the driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
8b0a6dba87 FILS: Connect request for offloaded FILS shared key authentication
Add FILS/ERP parameters into the driver connect command to support FILS
shared key authentication offload.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
79f3121bb4 FILS: Set cache identifier in current PMKSA entry for driver-SME case
This was already done in sme_send_authentication() for the case where
wpa_supplicant SME is used. Similar change is needed for driver-SME to
allow FILS authentication to be offloaded to the driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
42e69bda2a FILS: Add support for Cache Identifier in add/remove PMKSA
Add support for setting and deleting PMKSA cache entries based on FILS Cache
Identifer. Also additionally add support for sending PMK as part of
SET_PMKSA to enable driver to derive keys in case of FILS shared key
offload using PMKSA caching.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 18:46:13 +03:00
Vidyullatha Kanchanapally
6fbb54140b driver: Move add_pmkid() and remove_pmkid() arguments into a struct
This makes it easier to add more arguments to these wpa_driver_ops
functions.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 17:03:35 +03:00
vamsi krishna
199eb3a4e6 FILS: Add support to write FILS key_mgmt values in network blocks
Add support to write FILS related key_mgmt values also while saving a
network block.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 16:12:41 +03:00
Jouni Malinen
af3e362fa7 FILS: Add MDE into Authentication frame for FILS+FT
When using FILS for FT initial mobility domain association, add MDE to
the Authentication frame from the STA to indicate this special case for
FILS authentication.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-04-02 13:23:34 +03:00
Jouni Malinen
c10e0ccc9e Hide *PMKSA_ADD parameters from debug log
PMKSA_ADD and MESH_PMKSA_ADD command arguments include keying material,
so show it in debug log only if requested to do with the command line -K
argument.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-04-02 12:37:33 +03:00
Shaul Triebitz
3d5f0e916d wpa_supplicant: Avoid associating to temp disabled SSID in ap_scan=2
In ap_scan=2 mode, wpa_supplicant_assoc_try() did not check whether the
SSID is temporarily disabled before trying to associate and this may
result in an infinite connect/disconnect loop. If the association
succeeds while the SSID is temporarily disabled, wpa_supplicant will
request to deauthenticate and that in turn will cause the SSID to be
temporarily disabled again. Fix that by postponing the association until
the SSID is no longer temporarily disabled.

Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
2017-03-29 15:03:16 +03:00
Masashi Honma
fbba28f8c5 P2P: Suppress warning on non-P2P config
Without CONFIG_P2P config, the following warning occurs if CONFIG_AP is
enabled for the build:

ap.c: In function ‘wpas_conf_ap_vht’:
ap.c:54:5: warning: unused variable ‘channel’ [-Wunused-variable]
  u8 channel = conf->channel;
     ^
ap.c:53:5: warning: unused variable ‘center_chan’ [-Wunused-variable]
  u8 center_chan = 0;
     ^

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-03-27 17:21:02 +03:00
Vidyullatha Kanchanapally
6a4363f5f5 MBO: Fix reject reason codes
This change fixes the following compilation warnings:

wnm_sta.c:1007:4: warning: implicit conversion from enumeration type
 'enum mbo_transition_reason' to different enumeration type
 'enum mbo_transition_reject_reason' [-Wenum-conversion]

The actual value of both MBO_TRANSITION_REASON_UNSPECIFIED and
MBO_TRANSITION_REJECT_REASON_UNSPECIFIED is 0, so this does not result
in any change in the contents of the frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-26 21:13:21 +03:00
Jouni Malinen
a34317b526 GAS: Handle no-ACK TX status for GAS request frames
Previously, only the success and failure (to TX) cases were handled. It
is also possible for the driver to transmit the frame, but not receive
an ACK from the recipient. Address that by waiting for a short period of
time for a response. This fixes cases where OSU provider icon fetching
could get stuck if no ACK frame is received.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-26 21:13:21 +03:00
Jouni Malinen
31e130f82c FILS: Add FILS-SK-PFS capability into "GET_CAPABILITY fils" command
Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-13 11:46:30 +02:00
Jouni Malinen
6498351670 FILS: Check FILS Indication element against local network profile
Do not try to use FILS authentication unless the AP indicates support
for the type the local network profile enforces.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 23:23:09 +02:00
Jouni Malinen
76e20f4fa7 FILS: Add FILS SK auth PFS support in STA mode
This adds an option to configure wpa_supplicant to use the perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime network profile parameter fils_dh_group is used to enable
this by specifying which DH group to use. For example, fils_dh_group=19
would use FILS SK PFS with a 256-bit random ECP group.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 23:20:32 +02:00
Jouni Malinen
6115238492 OWE: Add CONFIG_OWE=y build option
This can be used to enable OWE support in hostapd and wpa_supplicant
builds.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 20:43:06 +02:00
Jouni Malinen
0a6147991e OWE: Process Diffie-Hellman Parameter element in STA mode
This adds STA side addition of OWE Diffie-Hellman Parameter element into
(Re)Association Request frame and processing it in (Re)Association
Response frame.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 19:24:11 +02:00
Jouni Malinen
09368515d1 OWE: Process Diffie-Hellman Parameter element in AP mode
This adds AP side processing for OWE Diffie-Hellman Parameter element in
(Re)Association Request frame and adding it in (Re)Association Response
frame.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 19:24:11 +02:00
Jouni Malinen
f9561868ec OWE: Add driver capability flag for OWE AKM
Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 19:24:11 +02:00
Jouni Malinen
a1ea1b4522 OWE: Define and parse OWE AKM selector
This adds a new RSN AKM "OWE".

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-12 19:24:11 +02:00
Johannes Berg
b07ff9cb04 wpa_supplicant: Allow disabling HT in AP mode without HT overrides
Since VHT can be toggled explicitly, also expose being able to disable
HT explicitly, without requiring HT overrides. Continue making it
default to enabled though.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-11 11:11:55 +02:00
Johannes Berg
2124a615e3 wpa_supplicant: Allow explicit wide channel configuration for AP mode
Instead of deducing the wide (HT, VHT) channel configuration only
automatically in P2P mode, allow it to be configured in the network
in non-P2P mode.

Also allow all of these parameters to be configured through the control
interface or the configuration file.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-11 10:59:51 +02:00
Jörg Krause
57ee04dc7d wpa_cli: Execute action file in case of WPS_EVENT_TIMEOUT
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
2017-03-11 10:58:28 +02:00
Jörg Krause
6252b981d9 wpa_cli: Execute action file in case of WPS_EVENT_ACTIVE
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
2017-03-11 10:58:10 +02:00
Jörg Krause
acdf502197 WPS: Notify about WPS PBC event in Enrollee mode
Previously, the event "WPS-PBC-ACTIVE" was only generated when
wpa_supplicant is operating as WPS Registrar whereas "WPS-SUCCESS" or
"WPS-TIMEOUT" are generated for both, the Registrar and the Enrollee
roles.

Also generate the event when wpa_supplicant is operating as WPS Enrollee
to allow monitoring the begin and the end of a WPS PBC process.

Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
2017-03-11 10:56:58 +02:00
Johannes Berg
15e5ee0b75 wpa_supplicant: events: Don't bounce timeout reason through a buffer
There's no point in making the code use a stack buffer and first copying
the string there, only to copy it again to the output. Make the output
directly use the reason string.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-11 10:52:43 +02:00
Avraham Stern
e97d15b733 wpa_cli: Update wnm_bss_query auto complete message
It is now possible to add neighbor configuration to wnm_bss_query.
Update the auto complete message to reflect that.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-03-11 10:49:08 +02:00
Avraham Stern
15ab61eda0 WNM: Add option to configure candidates for BTM query candidate list
Add a mechanism to configure the candidates for BTM query candidate list
manually. This can be used to verify AP behavior for various candidates
preferences.

usage:
wnm_bss_query <reason> [neighbor=<BSSID>,<BSSID information>,
	                <operating class>,<channel number>,
			<PHY type>[,<hexdump of optional subelements>]]

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-03-11 10:47:28 +02:00
Avraham Stern
13bf18eda5 WNM: Use a dynamically allocated buffer for BTM query and response
BSS transition management query and response use a large static buffer
for the frame because the candidate list may require a lot of space.
However, in most cases the actually used space will be much less than
the buffer (since the candidate list is short or completely missing).

Use a dynamically allocated buffer instead and allocate it according
to the actual space needed.

While at it, remove unneeded filling of the MAC header in the Action
frames, since this gets ignored and wpa_drv_send_action() adds the MAC
header anyway.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-03-10 23:52:44 +02:00
Jouni Malinen
34f2851902 MBO: Parse MBO ANQP-element on STA
This extends the GAS/ANQP parser in wpa_supplicant to process MBO
ANQP-elements and indicate received Cellular Data Connection Preference
values over the control interface.

When a valid MBO ANQP-element is received, the following control
interface message is sent:

RX-MBO-ANQP <BSSID> cell_conn_pref=<value>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-10 18:57:12 +02:00
Jouni Malinen
8ecf2231fd ANQP: Extend ANQP_GET command to request without IEEE 802.11 elements
Previously, ANQP_GET required at least one IEEE 802.11 ANQP-element to
be requested. This is not really necessary, so allow a case where
num_ids == 0 as long as the request includes at least one Hotspot 2.0 or
MBO ANQP-element.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-10 17:02:22 +02:00
Avraham Stern
2316cb358c MBO: Add option to add MBO query list to ANQP query
MBO techspec v0.0_r27 changed the MBO ANQP-element format. The MBO
element in ANQP query should now include an MBO Query List element that
contains a list of MBO elements to query.

Add API to add the MBO Query List to an ANQP query.

Format:
ANQP_GET <addr> <info_id>[,<info_id>]...[,mbo:<subtype>...]

Example for querying neighbor report with MBO cellular data
connection preference:
ANQP_GET <bssid> 272,mbo:2

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-03-10 16:53:10 +02:00
Purushottam Kushwaha
d0330d57f3 nl80211: Add option to delay start of schedule scan plans
The userspace may want to delay the the first scheduled scan.
This enhances sched_scan to add initial delay (in seconds) before
starting first scan cycle. The driver may optionally choose to
ignore this parameter and start immediately (or at any other time).

This uses NL80211_ATTR_SCHED_SCAN_DELAY to add this via user
global configurable option: sched_scan_start_delay.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-09 15:44:26 +02:00
Jouni Malinen
b696f791ac RRM: Fix wpas_rrm_send_msr_report() loop handling
The while (len) loop was updating the next pointer at the end even when
len == 0, i.e., when the new next value won't be used. This could result
in reading one octet beyond the end of the allocated response wpabuf.
While the read value is not really used in practice, this is not correct
behavior, so fix this by skipping the unnecessary next pointer update in
len == 0 case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-08 16:16:37 +02:00
Avraham Stern
891aa65b88 RRM: Use dynamically allocated buffer for beacon report
The maximum required size for each Beacon Report element is known in
advance: it is the size of the Beacon Report element fixed fields + the
size of the Reported Frame Body subelement.

Allocate the buffer used for constructing the Beacon Report element
dynamically with the maximum needed size, instead of using a very
large static buffer.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-03-08 16:05:52 +02:00
Johannes Berg
a1f11e34c4 Use os_memdup()
This leads to cleaner code overall, and also reduces the size
of the hostapd and wpa_supplicant binaries (in hwsim test build
on x86_64) by about 2.5 and 3.5KiB respectively.

The mechanical conversions all over the code were done with
the following spatch:

    @@
    expression SIZE, SRC;
    expression a;
    @@
    -a = os_malloc(SIZE);
    +a = os_memdup(SRC, SIZE);
    <...
    if (!a) {...}
    ...>
    -os_memcpy(a, SRC, SIZE);

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-07 13:19:10 +02:00
Kanchanapally, Vidyullatha
af8bc24da3 MBO: Add support for transition reject reason code
Add support for rejecting a BSS transition request using MBO reject
reason codes. A candidate is selected or rejected based on whether it is
found acceptable by both wpa_supplicant and the driver. Also accept any
candidate meeting a certain threshold if disassoc imminent is set in BTM
Request frame.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-07 00:34:14 +02:00
Kanchanapally, Vidyullatha
3ab484928a nl80211: Driver command for checking BTM accept/reject
Add driver interface command using the QCA vendor extensions to check
the driverr whether to accept or reject a BSS transition candidate. For
the reject case, report an MBO reject reason code.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-07 00:20:29 +02:00
Avraham Stern
23cddd7519 wpa_supplicant: Fix non_pref_chan example
The parsing code expects non_pref_chan to be non-quoted.
Fix the example in wpa_supplicant.conf not to include
quotes.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-03-06 23:41:26 +02:00
Hu Wang
57d3c5913a Clear scan_res_handler on no-retry failure
Previously it was possible for wpa_s->scan_res_handler to remain set to
its old value in case wpa_drv_scan() failed and no retry for the scan
trigger was scheduled (i.e., when last_scan_req == MANUAL_SCAN_REQ).
This could result in getting stuck with the next connection attempt
after a failed "SCAN TYPE=ONLY" operation when wpa_s->scan_res_handler
was set to scan_only_handler().

Fix this by clearing wpa_s->scan_res_handler if wpa_drv_scan() fails and
no retry is scheduled.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-01 16:39:30 +02:00
Amarnath Hullur Subramanyam
e9518ae749 WFD: Add WFD R2 Subelements
Define and add support for WFD R2 Subelements.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-01 11:59:57 +02:00
Jouni Malinen
206516e8c2 af_alg: Crypto wrappers for Linux kernel crypto (AF_ALG)
CONFIG_TLS=linux can now be used to select the crypto implementation
that uses the user space socket interface (AF_ALG) for the Linux kernel
crypto implementation. This commit includes some of the cipher, hash,
and HMAC functions. The functions that are not available through AF_ALG
(e.g., the actual TLS implementation) use the internal implementation
(CONFIG_TLS=internal).

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-28 11:24:15 +02:00
Ashwini Patil
dca4b503f1 MBO: Fix minimum length check on non_pref_chan configuration
The reason detail field in non_pref_chan attribute was removed
from MBO draft v0.0_r25. Also oper_class can be 1 character for
few country codes (e.g., country code-UK, channel number-1). So the
shortest channel configuration is 7 characters.

This was missed in the earlier commit
4a83d4b686 ('MBO: Do not add reason_detail
in non_pref_chan attr (STA)') that took care of other changes related to
removal of the reason detail.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-26 12:26:22 +02:00
Jouni Malinen
c4bb39707f Fix AES-SIV build dependencies
aes-siv.c needs functions from aes-ctr.c and aes-omac1.c, so set
NEED_AES_CTR=y and NEED_AES_OMAC1=y if NEED_AES_SIV is defined. This
fixes some build configuration combinations where either of those
dependencies were not pulled in through other parameters. For example,
some CONFIG_FILS=y cases were impacted.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-26 12:05:40 +02:00
Jouni Malinen
694a3a0d64 mesh: Fix CONFIG_MESH=y build without CONFIG_IEEE80211W=y
Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-26 12:05:40 +02:00
Jouni Malinen
88a447556e Fix SELECT_NETWORK freq parameter
This functionality was originally added in commit
204c9ac4ee ('Extend select_network command
with freq= to reduce scan time') re-using wpa_s->manual_scan_freqs and
MANUAL_SCAN_REQ. That got broken when commit
35d403096e ('Set NORMAL_SCAN_REQ on
SELECT_NETWORK/ENABLE_NETWORK') started overriding wpa_s->scan_req for
SELECT_NETWORK.

Fix this by adding a new scan frequency list specifically for
SELECT_NETWORK so that this does not need to depend on any specific
wpa_s->scan_req value.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-26 12:05:40 +02:00
Saurav Babu
d02989f2e4 D-Bus: Notify mesh capability if driver supports it
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-02-26 12:05:40 +02:00
Jouni Malinen
b7286c1b5d FILS: External management of PMKSA cache entry with Cache Identifier
The PMKSA_GET and PMKSA_ADD commands can now use an optional extra
parameter to fetch and add PMKSA cache entries with the FILS Cache
Identifier.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-26 12:05:40 +02:00
Jouni Malinen
869af30728 FILS: Use FILS Cache Identifier to extend PMKSA applicability
This allows PMKSA cache entries for FILS-enabled BSSs to be shared
within an ESS when the BSSs advertise the same FILS Cache Identifier
value.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-26 12:05:40 +02:00
Jouni Malinen
6aea02e579 SME: Clear portValid on starting authentication to fix FILS
The ft_completed for FILS authentication case in
wpa_supplicant_event_assoc() depends on something having cleared
portValid so that setting it TRUE ends up authorizing the port. This
clearing part did not happen when using FILS authentication during a
reassociation within an ESS. Fix this by clearing portValid in
sme_send_authentication() just before the keys are cleared (i.e., the
old connection would not be usable anyway).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-21 12:51:48 +02:00
Jouni Malinen
ba9774bd76 FILS: Fix BSSID in reassociation case
The RSN supplicant implementation needs to be updated to use the new
BSSID whenever doing FILS authentication. Previously, this was only done
when notifying association and that was too late for the case of
reassociation. Fix this by providing the new BSSID when calling
fils_process_auth(). This makes PTK derivation use the correct BSSID.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-21 12:26:57 +02:00
Saurav Babu
213eb18851 dbus: Set mode to mesh in bss properties when mesh is supported
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-02-20 22:14:19 +02:00
Purushottam Kushwaha
3f23260da8 nl80211: Notify reason for connection timeout failure
This adds reason for timeout in event CTRL-EVENT-ASSOC-REJECT whenever
connection failure happens because of timeout. This extends the
"timeout" parameter in the event to include the reason, if available:
timeout=scan, timeout=auth, timeout=assoc.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-20 10:47:08 +02:00
Peng Xu
d512f406fc hostapd: Add IEEE 802.11ax HE IEs into Beacon/Probe Response frames
IEEE 802.11ax HE changes to include HE IEs in Beacon and Probe Response
frames. These elements are using vendor specific forms for now since the
IEEE 802.11ax draft is not yet finalized and the element contents is
subject to change.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-19 17:37:55 +02:00
Peng Xu
94380cb40a hostapd: Initial IEEE 802.11ax (HE) definitions
Add IEEE 802.11ax definitions for config, IEEE structures, and
constants. These are still subject to change in the IEEE process.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-19 17:37:52 +02:00
Masashi Honma
84ea61cffe mesh: Use correct rate in HT and legacy mixed environment
Let mesh STA A be a STA which has config disable_ht=1.
Let mesh STA B be a STA which has config disable_ht=0.
The mesh STA A and B was connected.

Previously, the mesh STA A sent frame with HT rate even though its HT
was disabled. This commit fixes the issue by checking the local BSS HT
configuration.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-02-19 16:01:17 +02:00
Masashi Honma
025c6a47fb VHT: Remove a redundant check
This check is already done in ibss_mesh_setup_freq().

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-02-19 16:01:17 +02:00
Jouni Malinen
c6c41f6ea6 FT: Support addition of RIC elements into Reassociation Request frame
The new "SET ric_ies <hexdump>" control interface command can now be
used to request wpa_supplicant to add the specified RIC elements into
Reassociation Request frame when using FT protocol. This is mainly for
testing purposes.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-18 21:39:01 +02:00
Jouni Malinen
62944f7d2c Add HMAC-SHA384 with internal crypto
This is a copy of the internal HMAC-SHA256 implementation with the hash
block size and output length updated to match SHA384 parameters.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-16 22:15:29 +02:00
Jouni Malinen
3a7819f0ad P2P: Add P2P_SET override_pref_op_chan to allow overriding preference
This new P2P_SET parameter uses <op_class>:<channel> format and is used
mainly for testing purposes to allow overriding the value of the GO
Negotiation Response frame Operating Channel attribute.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-16 12:08:22 +02:00
Jouni Malinen
c06fca04fd Add wpa_supplicant SET get_pref_freq_list_override
This can be used to override driver get_pref_freq_list() operation for
more convenient testing of preferred frequency list functionality.

Override string format:
<if_type1>:<freq1>,<freq2>,... <if_type2>:...

if_type: 0=STATION, 2=AP, 3=P2P_GO, 4=P2P_CLIENT, 8=TDLS, 9=IBSS

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-16 12:08:22 +02:00
Jouni Malinen
b4d56efb1a Use throughput estimate-based BSS selection with larger SNR difference
Previously, the est_throughput comparison was done only when SNR
difference was less than 5 dB. Since the throughput estimation take into
account SNR, this can be done in more cases. For now, add a conservative
2 dB more to the difference so that any SNR difference below 7 dB
results in BSS selection based on throughput estimates.

In addition, the throughput estimates require SNR values to be
available, so separate this from the 5 GHz preference that can be done
based on either SNR or qual values.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-16 12:05:10 +02:00
Jouni Malinen
1420414878 Drop GREAT_SNR definition from 30 to 25 dB
This allows throughput estimates and 5 GHz preference over 2.4 GHz band
to be used in more cases. The previously used value of 30 was
significantly more conservative than the SNR limits used for the highest
rate in scan_est_throughput() and this resulted in cases where 5 GHz AP
was ignored while SNR with it would have been close to reaching the
maximum TX rate.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-16 11:15:13 +02:00
Jouni Malinen
b5562a1a6e FILS: Remove CRC32 dependency from build
The published P802.11ai version does not use CRC32 anymore, so remove
inclusion of crc32.o into wpa_supplicant and hostapd builds based on
CONFIG_FILS=y.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-13 23:17:31 +02:00
Jouni Malinen
577e794eba Sync android.config with wpa_supplicant defconfig changes
This adds new edits from defconfig to android.config. No new build
options are enabled, i.e., this is only bringing in comment updates and
new parameters in commented out form.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-11 10:21:56 +02:00
Jouni Malinen
784710b7ff Add bgscan options to wpa_supplicant defconfig
Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-11 10:21:24 +02:00
Jouni Malinen
212a8f487f Fix wpa_supplicant defconfig copy-paste description
This is obviously for the wpa_supplicant binary, not hostapd.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-11 10:12:16 +02:00
vamsi krishna
57c3a605ce Add support to sched scan to report relatively better BSSs
Add support to set sched scan relative RSSI parameters so that the
drivers can report BSSs after relative comparision with the current
connected BSS. This feature is applicable only when in connected mode.

The below commands can be used to configure relative RSSI parameters
SET relative_rssi <disable|rssi_value>
	disable - to disable the feature
	rssi_value - amount of relative RSSI in dB
SET relative_band_adjust <band:adjust_value>
	band - "2G" or "5G" for 2.4 GHz or 5 GHz respectively
	adjust_value - amount of RSSI to be adjusted in dB

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-10 19:48:12 +02:00
Paul Stewart
ed9b1c16d5 EAP peer: Cache decrypted requests for EAP-SIM/AKA/AKA'
Add an internal flag which indicates to tunneled EAP methods (FAST,
PEAP, TTLS) that they should cache decrypted EAP-SIM/AKA/AKA' requests.
This allows EAP-SIM/AKA/AKA' to be tunneled within these outer methods
while using an external SIM authenticator over the control interface.

Signed-off-by: Paul Stewart <pstew@google.com>
2017-02-10 19:48:12 +02:00
Jouni Malinen
5f11880f6a SME: Remove null ie param from CTRL-EVENT-AUTH-REJECT
Clean up the event message by removing the ie=<value> parameter when the
IEs are not available instead of printing out "ie=(null)".

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-10 19:48:12 +02:00
Jouni Malinen
4d70b2a4e5 RRM: Fix a memory leak in beacon request handling
Free the pending frequency list if a second beacon request is received
before the scan for the previous one has been completed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-10 19:48:04 +02:00
vamsi krishna
b4fd1f0ed7 Allow PNO scan also in connection completed state
Sched scan is supported by the kernel also in the connected state, so
allow PNO scan to be issued in the connected state from wpa_supplicant
as well.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-08 15:55:35 +02:00
Jouni Malinen
4c6f450cad Add radio_work_is_connect() helper
This avoids duplicated code to check for different types of connection
radio work items.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-07 23:58:56 +02:00
Sunil Dutt
85b6b6b6e1 Serialize scan/p2p-scan if already scheduled on the same interface
The current implementation of QCA vendor scan does not handle the
simultaneous scan/p2p-scan operations on the same interface due to
missing support for tracking multiple scan cookie values. Hence
serialize such operations on the same interface for now.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-07 23:58:55 +02:00
Jouni Malinen
fcb303a57f P2P: Clear driver scan cache after BSS_FLUSH
The only_new_results=1 scan parameter was previously set on other scan
cases, but not on the two P2P specific scan triggers. Set this also for
those P2P cases to get consistent behavior after BSS_FLUSH.

This was showing up with number of hwsim P2P test cases maintaining
unexpected scan results from previous test cases due to the flush
operation not really working correctly since the cfg80211 BSS table was
not explicitly cleared.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-07 22:48:20 +02:00
Vamsi Krishna
1d9d21f376 GAS: Add support to randomize transmitter address
Add support to send GAS requests with a randomized transmitter address
if supported by the driver. The following control interface commands
(and matching configuration file parameters) can be used to configure
different types of randomization:

"SET gas_rand_mac_addr 0" to disable randomizing TX MAC address,
"SET gas_rand_mac_addr 1" to randomize the complete TX MAC address,
"SET gas_rand_mac_addr 2" to randomize the TX MAC address except for OUI.

A new random MAC address will be generated for every
gas_rand_addr_lifetime seconds and this can be configured with
"SET gas_rand_addr_lifetime <timeout>".

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-07 19:41:32 +02:00
Masashi Honma
f3e1570576 VHT: Fill VHT capability with hardware capability
Previously, VHT capability was default value (=0x0000). This makes
VHT Capabilities Info in VHT Capabilities IE in mesh peering
open/confirm frame 0x0000. This patch fills it with hardware capability.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-02-07 11:14:55 +02:00
Günther Kelleter
41f140d386 Add hostapd options wpa_group_update_count and wpa_pairwise_update_count
wpa_group_update_count and wpa_pairwise_update_count can now be used to
set the GTK and PTK rekey retry limits (dot11RSNAConfigGroupUpdateCount
and dot11RSNAConfigPairwiseUpdateCount). Defaults set to current
hardcoded value (4).

Some stations may suffer from frequent deauthentications due to GTK
rekey failures: EAPOL 1/2 frame is not answered during the total timeout
period of currently ~3.5 seconds. For example, a Galaxy S6 with Android
6.0.1 appears to go into power save mode for up to 5 seconds. Increasing
wpa_group_update_count to 6 fixed this issue.

Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
2017-02-07 00:25:36 +02:00
Sunil Dutt
f47f936170 P2P: Override P2P_PEER group_capab with 0 if no matching BSS entry found
Relying on the group_capab from the P2P peer information can result in
improper information on whether the peer is currently operating as a GO.
However, there is a known implementation in Android that does this.

To reduce issues from this misuse in upper layer to try to determine
whether a specific peer is operationg a group, override the group_capab
value in P2P_PEER output with 0 if there are no BSS entries with the
peer P2P Device as a GO. This is not a perfect information since there
may not have been a recent scan on all channels, but this results in
less issues than trying to decide between new group formation and
joining an existing group based on stale or incorrect information.

Since no upper layer application is really supposed to use the
group_capab field value in P2P_PEER command, this change should not
cause any impact for properly design components and the possibility of
regressions is limited to cases that are already known to work
incorrectly in number of identifiable cases.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-06 12:17:12 +02:00
Jouni Malinen
bcf66493cf Fix estimated throughput based skip-roam case
Commit 8d1e693186 ('Use estimated
throughput to avoid signal based roaming decision') added a check for
the current BSS estimated throughput being significantly higher than the
selected BSS estimated throughput. However, this case for skipping a
roam used "return 1" which actually allows the roam. Fix this by
returning 0 in this case.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-05 21:52:26 +02:00
Jouni Malinen
1fb4437c80 tests: Validate hwaddr/hexstr input to DRIVER_EVENT SCAN_RES
To be more consistent with existing hwaddr_aton() and hexstr2bin()
callers, check the return values in this test command.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-05 16:31:03 +02:00
Jouni Malinen
db5e53cb06 mesh: Fix struct hostapd_data initialization
The local custom version of allocating and initializing struct
hostapd_data within wpa_supplicant_mesh_init() is problematic. This has
already missed couple of initialization steps that are required. Instead
of trying to remember to keep this up to date, use
hostapd_alloc_bss_data() so that there is only one place for this
initialization.

This is fixing a recent issue where FILS HLP started using
hapd->dhcp_server and expected that to be initialized to -1. For the
mesh case, that did not happen and when removing the interface, the FILS
HLP implementation ended up unregistering eloop socket for
hapd->dhcp_server (= 0). This could result in missing socket callbacks
for an arbitrary socket.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-04 22:17:54 +02:00
Jouni Malinen
9b170991ac mesh: Fix mesh interface removal fix
This wpa_drv_if_remove() call was previously modified to fix a different
issue, but that fix resulted in unconditional use of treed memory here
(wpa_supplicant_deinit_iface() frees wpa_s). Make a local copy of
wpa_s->parent to be able to use it after wpa_s is freed. The
mesh_if_created case has wpa_s->parent != wpa_s, so this should be
sufficient way of handling the wpa_drv_if_remove() call here.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-04 21:24:37 +02:00
Jouni Malinen
124ddfa19e FILS: Parse and report received FILS HLP Containers from response
The new FILS-HLP-RX control interface event is now used to report
received FILS HLP responses from (Re)Association Response frame as a
response to the HLP requests configured with FILS_HLP_REQ_ADD.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-01 18:17:39 +02:00
Jouni Malinen
54b04d6f39 FILS: Move HLP request handling into a separate file
This is independent functionality from the core IEEE 802.11 management
handling and will increase significantly in size, so it is cleaner to
maintain this in a separate source code file.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-31 17:46:13 +02:00
Dmitry Shmidt
f2bc344808 wpa_supplicant: Fix global control interface for STA/STA-FIRST/STA-NEXT
update_stations(ctrl_conn) is stuck in never-ending loop:

sendto(3, "STA-FIRST", 9, 0, NULL, 0)   = 9
pselect6(4, [3], NULL, NULL, {10, 0}, NULL) = 1 (in [3], left {9, 999995000})
recvfrom(3, "UNKNOWN COMMAND\n", 4095, 0, NULL, NULL) = 16
sendto(3, "STA-NEXT UNKNOWN COMMAND", 24, 0, NULL, 0) = 24
pselect6(4, [3], NULL, NULL, {10, 0}, NULL) = 1 (in [3], left {9, 999995833})
recvfrom(3, "UNKNOWN COMMAND\n", 4095, 0, NULL, NULL) = 16
sendto(3, "STA-NEXT UNKNOWN COMMAND", 24, 0, NULL, 0) = 24
pselect6(4, [3], NULL, NULL, {10, 0}, NULL) = 1 (in [3], left {9, 999995000})
recvfrom(3, "UNKNOWN COMMAND\n", 4095, 0, NULL, NULL) = 16
sendto(3, "STA-NEXT UNKNOWN COMMAND", 24, 0, NULL, 0) = 24

Direct STA, STA-FIRST, and STA-NEXT commands from the global control
interface to a per-interface control interface to avoid this.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2017-01-30 01:54:22 +02:00
Jouni Malinen
0da355235e FST: Remove WPA_ASSERT from wpas_fst_send_action_cb()
It was possible to hit this WPA_ASSERT when FST-MANAGER SESSION_REMOVE
command is exececuted when in not-associated state. In
CONFIG_EAPOL_TEST=y builds, this would result in the wpa_supplicant
process being terminated. Convert this WPA_ASSERT to a check that does
not terminate the process, but only rejects the command if wpa_s->bssid
does not match the da argument.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-29 19:22:14 +02:00
Andrejs Cainikovs
6a5425fd60 Increase delayed EAPOL RX frame timeout
Increase the EAPOL RX frame timeout from 100 to 200 ms. This fixes lack
of optimization (i.e., first EAPOL frame dropped) in occasional roaming
and authentication cases on EAP networks if the kernel events can be
reordered and delayed a bit longer.

Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
2017-01-29 18:41:29 +02:00
Johannes Berg
cef8fac04b wpa_auth: Make struct wpa_auth_callbacks const
Instead of copying the struct wpa_auth_callbacks, just keep a pointer to
it, keep the context pointer separate, and let the user just provide a
static const structure. This reduces the attack surface of heap
overwrites, since the function pointers move elsewhere.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-01-29 18:41:26 +02:00
Johannes Berg
30eddf3529 Fix or supress various sparse warnings
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-01-29 18:33:10 +02:00
Jouni Malinen
b301f54e55 IBSS/mesh: Skip VHT channel setup with vht_disabled=1
If the VHT capability override vht_disabled=1 is used in the network
profile, skip VHT configuration of the local channel.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-29 18:31:54 +02:00
Masashi Honma
adc6a5d81a mesh: Check remote peer HT Operation element
The remote mesh STA which had configuration disable_ht40=1 could have HT
Capabilities element which includes Supported Channel Width Set = 1
(both 20 MHz and 40 MHz operation is supported) even though it had HT
Operation element which includes STA Channel Width = 0 (20 MHz channel
width only). Previously, local peer recognized such a remote peer as 40
MHz band width enabled STA because local peer only checked HT
Capabilities element. This could cause disconnection between
disable_ht40=1 mesh STA and disable_ht40=0 mesh STA. They could
establish a mesh BSS but could not ping with ath9k_htc device. This
commit fixes the issue by refering HT Operation element.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-01-29 18:04:21 +02:00
Masashi Honma
9eb5757a86 Define helper function set_disable_ht40()
This functionality can be used outside wpa_set_disable_ht40(), so move
the generic part to a helper function.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-01-29 18:04:21 +02:00
Saurav Babu
6b585f420a mesh: Fix crash on removing virtual mesh interface
If a virtual mesh interface has been created and is still operational
when the main interface is removed (e.g., Wi-Fi hardware ejected), the
following crash occurred with the below backtrace:

WPA_TRACE: eloop SIGSEGV - START
[1]: /usr/local/sbin/wpa_supplicant() [0x44ef7e]
     eloop_sigsegv_handler() home/saurav/hostap/wpa_supplicant/../src/utils/eloop.c:123
[2]: /lib/x86_64-linux-gnu/libc.so.6(+0x36d40) [0x7f4c395cfd40]
[3]: /usr/local/sbin/wpa_supplicant(wpa_supplicant_remove_iface+0xd0) [0x57f500]
     wpa_supplicant_remove_iface() home/saurav/hostap/wpa_supplicant/wpa_supplicant.c:5338
[4]: /usr/local/sbin/wpa_supplicant() [0x57fbef]
     wpa_supplicant_deinit_iface() home/saurav/hostap/wpa_supplicant/wpa_supplicant.c:5069
[5]: /usr/local/sbin/wpa_supplicant(wpa_supplicant_remove_iface+0xc5) [0x57f4f5]
     wpa_supplicant_remove_iface() home/saurav/hostap/wpa_supplicant/wpa_supplicant.c:5343
[6]: /usr/local/sbin/wpa_supplicant(wpas_dbus_handler_remove_interface+0x8d) [0x55baad]
     wpas_dbus_handler_remove_interface() home/saurav/hostap/wpa_supplicant/dbus/dbus_new_handlers.c:679
[7]: /usr/local/sbin/wpa_supplicant() [0x5560cb]
     msg_method_handler() home/saurav/hostap/wpa_supplicant/dbus/dbus_new_helpers.c:354
     message_handler() home/saurav/hostap/wpa_supplicant/dbus/dbus_new_helpers.c:410
[8]: /lib/x86_64-linux-gnu/libdbus-1.so.3(+0x1be86) [0x7f4c39979e86]
[9]: /lib/x86_64-linux-gnu/libdbus-1.so.3(dbus_connection_dispatch+0x381) [0x7f4c3996ca21]
[10]: /usr/local/sbin/wpa_supplicant() [0x567148]
     dispatch_data() home/saurav/hostap/wpa_supplicant/dbus/dbus_common.c:36
[11]: /usr/local/sbin/wpa_supplicant() [0x5674a7]
     process_watch() home/saurav/hostap/wpa_supplicant/dbus/dbus_common.c:75
     process_watch_read() home/saurav/hostap/wpa_supplicant/dbus/dbus_common.c:90
[12]: /usr/local/sbin/wpa_supplicant() [0x44f297]
     eloop_sock_table_dispatch() home/saurav/hostap/wpa_supplicant/../src/utils/eloop.c:598
[13]: /usr/local/sbin/wpa_supplicant(eloop_run+0x1fe) [0x44ff1e]
     eloop_run() home/saurav/hostap/wpa_supplicant/../src/utils/eloop.c:1219
[14]: /usr/local/sbin/wpa_supplicant(wpa_supplicant_run+0x77) [0x57fd87]
     wpa_supplicant_run() home/saurav/hostap/wpa_supplicant/wpa_supplicant.c:5608
[15]: /usr/local/sbin/wpa_supplicant(main+0x3a8) [0x43ba88]
     main() home/saurav/hostap/wpa_supplicant/main.c:392
WPA_TRACE: eloop SIGSEGV - END
Aborted (core dumped)

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-01-29 17:42:02 +02:00
Jouni Malinen
5732b770f4 FILS: Allow FILS HLP requests to be added
The new wpa_supplicant control interface commands FILS_HLP_REQ_FLUSH and
FILS_HLP_REQ_ADD can now be used to request FILS HLP requests to be
added to the (Re)Association Request frame whenever FILS authentication
is used.

FILS_HLP_REQ_ADD parameters use the following format:
<destination MAC address> <hexdump of payload starting from ethertype>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-29 14:32:17 +02:00
Jouni Malinen
afe731004b Fix CONFIG_SAE build without CONFIG_SME
The control interface code was using wpa_s->sme in an area that was not
within ifdef CONFIG_SME.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-28 11:58:26 +02:00
Jouni Malinen
34e8bfd7a9 Skip EVENT_ACS_CHANNEL_SELECTED also without CONFIG_AP
CONFIG_ACS alone should not refer to wpa_s->ap_iface to avoid potential
compilation issues.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-28 11:57:23 +02:00
vamsi krishna
53b38209f4 GAS: Cancel gas_query_timeout when AP responds with comeback delay
When AP responds with comeback delay for initial GAS query sent by STA,
gas_query_timeout should be cancelled to avoid GAS failures when
comeback delay is more than GAS_QUERY_TIMEOUT_PERIOD. The
gas_query_timeout is getting registered again when tx_status is received
for GAS comeback request.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-23 07:02:30 +02:00
Masashi Honma
4d77d80edd mesh: Add MESH_PMKSA_GET/ADD commands
These commnds are mesh version of PMKSA_GET/ADD commands. So the usage
and security risk is similar to them. Refer to
commit 3459381dd2 ('External persistent
storage for PMKSA cache entries') also.

The MESH_PMKSA_GET command requires peer MAC address or "any" as an
argument and outputs appropriate stored PMKSA cache. And the
MESH_PMKSA_ADD command receives an output of MESH_PMKSA_GET and re-store
the PMKSA cache into wpa_supplicant. By using re-stored PMKSA cache,
wpa_supplicant can skip commit message creation which can use
significant CPU resources.

The output of the MESH_PMKSA_GET command uses the following format:
<BSSID> <PMKID> <PMK> <expiration in seconds>

The example of MESH_PMKSA_ADD command is this.
MESH_PMKSA_ADD 02:00:00:00:03:00 231dc1c9fa2eed0354ea49e8ff2cc2dc cb0f6c9cab358a8146488566ca155421ab4f3ea4a6de2120050c149b797018fe 42930
MESH_PMKSA_ADD 02:00:00:00:04:00 d7e595916611640d3e4e8eac02909c3c eb414a33c74831275f25c2357b3c12e3d8bd2f2aab6cf781d6ade706be71321a 43180

This functionality is disabled by default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2017-01-14 18:07:46 +02:00
Jouni Malinen
117875db33 D-Bus: Add GroupMgmt entry into the interface Capabilities dict
This can be used to determine whether the driver supports PMF and if so,
with which group management cipher suites. In addition, add the missing
pairwise and group cipher suite values to the documentation while adding
this new entry there as well.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-14 17:41:20 +02:00
Stijn Tintel
3cdb4ac074 D-Bus: Add pmf to global capabilities
This indicates that the wpa_supplicant binary has been compiled with PMF
support.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-01-14 17:29:22 +02:00
Stijn Tintel
adf8f45f8a D-Bus: Implement Pmf property
The Pmf property is documented in doc/dbus.doxygen, but does not exist,
so implement it.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-01-14 17:28:00 +02:00
Jouni Malinen
b98706c14b RSN IBSS: Fix TK clearing on Authentication frame RX
When wpa_supplicant was processing a received Authentication frame (seq
1) from a peer STA for which there was already a TK configured to the
driver, debug log claimed that the PTK gets cleared, but the actual
call to clear the key was actually dropped due to AUTH vs. SUPP set_key
selection. Fix this by explicitly clearing the TK in case it was set
and an Authentication frame (seq 1) is received.

This fixes some cases where EAPOL-Key frames were sent encrypted using
the old key when a peer STA restarted itself and lost the key and had to
re-join the IBSS. Previously, that state required timing out the 4-way
handshake and Deauthentication frame exchange to recover.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-14 13:56:18 +02:00
Johannes Berg
f09095d57b wpa_supplicant: Clarify group_rekey documentation
This is also used in mesh and AP modes.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-01-13 15:05:26 +02:00
Jouni Malinen
8f315d0505 Fix country code in wpa_supplicant AP mode Country element
country[2] needs to be set to ' ' instead of left to '\0' for the case
where wpa_supplicant sets up AP mode operations and includes the Country
element. Currently, this would be only for DFS channels. Without this,
the Beacon frames would go out with incorrect third octet in the country
code.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-13 15:05:26 +02:00
Jouni Malinen
e4a3e1d076 tests: Add DRIVER_EVENT SCAN_RES for scan result testing
This control interface command can be used to inject scan results from
test scripts to make it easier to test various scan result processing
operations.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 18:39:24 +02:00
Jouni Malinen
29065686ac D-Bus: Fix BSS Mode getter for invalid DMG BSS
Previous version could have used uninitialized char* when a DMG with
invalid capabilities were added to BSS table from scan results.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 18:39:24 +02:00
Jouni Malinen
2901bc2725 bgscan: Remove unnecessary NULL check
The name argument to bgscan_init() cannot be NULL since the only caller
already checks this before the call.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 14:44:34 +02:00
Jouni Malinen
9d6eaad6b8 bgscan: Remove unnecessary NULL check
bgscan_init() is the only caller for the init() function and the
parameters argument is never NULL.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 12:43:33 +02:00
Jouni Malinen
0f9b4a0f1d bgscan: Deliver beacon loss event to bgscan modules
This adds a call to the notify_beacon_loss() callback functions when
beacon loss is detected. In addition, a new CTRL-EVENT-BEACON-LOSS event
is made available through the wpa_supplicant control interface.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 12:17:58 +02:00
Jouni Malinen
54736d8358 Store FST parameters to configuration file
This was forgotten when the parameters were added.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 00:10:57 +02:00
Jouni Malinen
35c78f7b97 Store osu_dir to configuration file
This was forgotten when the parameter was added.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 00:10:57 +02:00
Jouni Malinen
1f539c78f4 Store autoscan to configuration file
This was forgotten when the parameter was added.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 00:10:57 +02:00
Jouni Malinen
58ed9e31d1 Store filter_rssi to configuration file
This was forgotten when the parameter was added.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 00:10:57 +02:00
Jouni Malinen
1fb1bf99d6 Write sec_device_type to configuration file
This is more consistent with other global configuration parameters.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 00:10:57 +02:00
Jouni Malinen
b4bdeadfaf Make "SET" behavior more consistent for dot11RSNA parameters
These parameters are global configuration parameters for wpa_supplicant
and the special control interface SET command handlers for them were
preventing the configuration update. Make this more consistent by
updating the configuration parameter as well since that is what all the
other SET <global config param> commands do.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 00:10:57 +02:00
Jouni Malinen
e3394c0e2c Make "SET non_pref_chan .." behavior more consistent
non_pref_chan is a global configuration parameter for wpa_supplicant and
the special control interface SET command handler for it was preventing
the configuration update. Make this more consistent by updating the
configuration parameter as well since that is what all the other SET
<global config param> commands do.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 00:10:57 +02:00
Jouni Malinen
f8c201862e Fix cert_in_cb parsing in wpa_supplicant.conf
Commit 483dd6a5e0 ('Include peer
certificate always in EAP events') added this wpa_supplicant global
configuration parameter, but forgot to add the actual parsing of it, so
there was no way of setting the value.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 00:10:57 +02:00
Jouni Malinen
9284418d00 Fix writing of wpa_supplicant sae_groups configuration parameter
This integer array is zero terminated, so need to check the value is
greater than 0 when writing the parameter.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-08 00:10:57 +02:00
Jouni Malinen
7ba94fc4b0 RRM: Use wpa_hexdump_buf() instead of wpa_hexdump()
Simplify the code a bit by using the appropriate debugging function to
dump a wpabuf contents.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-07 18:47:37 +02:00
Jouni Malinen
33468e5320 RRM: Document Link Measurement Report frame construction steps
Add a comment to note which fields are expected to be updated by the
driver. In addition, reorder subfield writing to match the order in
which the fields are in the frame.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-07 18:17:59 +02:00
Jouni Malinen
40e9a3f326 RRM: Fix beacon report scan channels for VHT 80, 80+80, 160 MHz cases
ieee80211_chan_to_freq() is not really meant for conversion of 20 MHz
primary channel numbers for wider VHT channels, so handle those as
special cases here for now.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-07 12:49:48 +02:00
Jouni Malinen
5cda350896 RRM: Move wpabuf_resize() call into wpas_rrm_report_elem()
wpabuf_resize() can handle the initial allocation of a wpabuf and all
the other callers of wpas_rrm_report_elem() were already using a pointer
to a pointer and a wpabuf_resize() call. Simplify this by resizing the
wpabuf (if needed) within wpas_rrm_report_elem() instead of having to
calculate the needed size in all the callers. Thsi is also fixing one of
the allocation sizes to use the correct size instead of a size of a
struct that has nothing to do with the allocation (but is larger than
the needed five octets, so does not break anything).

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-07 12:13:20 +02:00
Jouni Malinen
f2058f4afa RRM: Remove unnecessary cb check
There is only a single caller for wpas_rrm_send_neighbor_rep_request()
and it unconditionally uses a callback function, so cb cannot be NULL
here and there is no need for additional complexity and extra code size
to check for it explicitly.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-07 12:11:49 +02:00
Beni Lev
e72faadb49 bgscan_simple: Fix short_scan_count comparison
Previously, the check was done after we reached the maximum and another
scan was already triggered.

While at it, remove an irrelevant comment that the previous change in
the logic here missed.

Signed-off-by: Beni Lev <beni.lev@intel.com>
2017-01-05 16:36:14 +02:00
Purushottam Kushwaha
c167662d73 eap_proxy: On SIM error flush PMKSAs only for SIM/AKA/AKA' networks
Previously, SIM state change with SIM_STATE_ERROR cleared all PMKSA
entries (including non-SIM networks). Limit this to networks which use
SIM-based authentication methods to avoid unnecessarily removal of PMKSA
entries.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-04 21:56:43 +02:00
Jouni Malinen
6657bb158b Fix OOM handling in neighbor report response handling
The pending neighbor report state needs to be cleared on error path here
to avoid getting stuck with being unable to perform any additional
neighbor reports during the association.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-03 19:53:03 +02:00
Jouni Malinen
7187e20930 Allow LCI request with no subelements
Allow shorter request since the subelements are optional to include.
Also print the hexdump of the subelements into debug log.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-03 19:53:03 +02:00
Jouni Malinen
d734201435 RRM: Enable beacon report with active/passive scan for all drivers
The requested behavior can be approximated for most use cases even if
the driver does not support reporting exact TSF values for frames.
Enable this capability for all drivers to make beacon report processing
more useful for a common use case.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-03 19:53:03 +02:00
Jouni Malinen
de6ec8b558 Enable Beacon Report using beacon table for all drivers
The special parameters for beacon report scan are not needed for the
beacon report when using the beacon table measurement mode. Advertise
support for this case regardless of whether the driver supports the scan
parameters.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-03 16:02:56 +02:00
Jouni Malinen
6774c6a9fe Update copyright notices for the new year 2017
Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-03 15:18:30 +02:00
Avraham Stern
76196ddb2b wpa_supplicant: Add support for Beacon Report Radio Measurement
Beacon Report Radio Measurement is defined in IEEE Std 802.11-2016,
11.11.9.1. Beacon Report is implemented by triggering a scan on the
requested channels with the requested parameters.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-01-03 15:18:30 +02:00
Avraham Stern
b3060bf99f common: Add helper function to convert RSSI to RCPI
This conversion will be done several times in the code, so add a helper
function that does this conversion.

Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
2017-01-03 15:18:29 +02:00
Avraham Stern
1ac4dba31a wpa_supplicant: Extend verify_channel() and make it global
Extend verify_channel() to return whether IR is allowed on the channel
or not, and make it a global function so it can be used in other files,
too. This makes this function useful for checking not only if a channel
is supported but also if it is allowed for active and passive scan.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-01-03 15:18:29 +02:00
Avraham Stern
c16b9f8d33 driver: Add scan support to beacon report
Add the following parameters to scan request:
 1. Dwell time on each channel.
 2. Whether the specified dwell time is mandatory.

In addition, add to scan results info the time that the scan actually
started, and to each scan result the time the beacon/probe was received,
both in terms of TSF of the BSS that the interface that requested the
scan is connected to (if available).

Add flags to indicate whether the driver supports dwell time
configuration and scan information reporting.

This scan configuration and information is required to support beacon
report radio measurement.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-01-03 15:18:29 +02:00
Avraham Stern
3c716fdbd7 wpa_supplicant: Refactor wpas_rrm_build_lci_report()
1. Change the return type to reflect whether building the report
   succeeded or failed.
2. Change argument type to rrm_measurement_request_element instead
   of raw packet data to ease processing the request.
3. Use already existing function to create the measurement report
   and add it to the report buffer.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-01-03 15:18:29 +02:00
Avraham Stern
e1b96e1126 wpa_supplicant: Send rejection for unsupported radio measurements
Send measurement report with the mode field set to incapable in response
to measurement requests with unsupported measurement types.

In addition, measurements requests that request parallel measurements
are rejected since these features are not supported.

Measurement request frames with the enable bit set are ignored since
these are not really requesting measurements and are not supported for
now.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-01-03 15:18:29 +02:00
Avraham Stern
0c73e410d6 wpa_supplicant: Limit RRM response size to MMPDU size
The length of a Measurement Report frame should be limited by the
maximum allowed MMPDU size (IEEE Std 802.11-2016, 9.6.2.3). Enforce this
size limit, and in case the report elements are longer than the allowed
size, split them between several MPDUs.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-01-03 15:18:29 +02:00
Avraham Stern
9664ab8b71 wpa_supplicant: Refactor Radio Measurement Request handling
Extract the code dealing with processing the measurement request
elements to a separate function. This will be needed for beacon report
requests processing.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-01-03 15:18:29 +02:00
Avraham Stern
332bf5d3fc wpa_supplicant: Validate RRM request frame format
RRM request frame should contain only information elements of type Radio
Measurement Request. Go through all the frame and validate that only
elements of this type are included.

In addition, if a truncated element is encountered, or the element
length field indicates that the element length is more than the
entire frame, abort the request.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-01-03 15:18:29 +02:00
Avraham Stern
ec493469f6 wpa_supplicant: Move RRM implementation to a dedicated file
As support for new RRM measurements will be added, the RRM
implementation will become quite large, so move it to a dedicated file.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2017-01-03 15:18:29 +02:00
Jouni Malinen
6a31440b86 Fix LCI request subelement processing
Commit 4a742011ab ('wpa_supplicant: Handle
LCI request') introduced LCI request parsing in a manner that
incremented the request pointer by four within
wpas_rrm_build_lci_report() without decrementing len correspondingly.
This could potentially result in get_ie() reading four octets beyond the
buffer if a corrupted request is received. This would be applicable only
if the LCI reporting was enabled explicitly ("SET LCI ..." control
interface command).

Fix this by updating the len variable to match the request pointer
changes.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-01-03 15:18:29 +02:00
Masashi Honma
ce691a8d96 Add CONFIG_MESH into wpa_supplicant defconfig
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2016-12-30 23:59:47 +02:00
Masashi Honma
67129ab9ec wpa_cli: Add commands to use PMKSA_GET/ADD
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2016-12-30 23:59:34 +02:00
Badrish Adiga H R
65dfa87286 mka: Make MKA actor priority configurable
This adds a new wpa_supplicant network profile parameter
mka_priority=0..255 to set the priority of the MKA Actor.

Signed-off-by: Badrish Adiga H R <badrish.adigahr@gmail.com>
2016-12-25 11:41:46 +02:00
Jouni Malinen
77fcbf7ff1 D-Bus: Use a helper function to get possibly NULL strings
This type of check is used in quite a few getter functions, so add a
helper function to take care of it.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-23 21:28:43 +02:00
Avichal Agarwal
dbf524946b D-Bus: Add DeviceType in WPS property
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
2016-12-23 21:28:43 +02:00
Avichal Agarwal
266097fdad D-Bus: Add device serial number in WPS property
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
2016-12-23 11:02:43 +02:00
Avichal Agarwal
3ee6a3ab35 D-Bus: Add model number in WPS property
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
2016-12-23 10:59:53 +02:00
Avichal Agarwal
ae66822cd8 D-Bus: Add WPS model name as property
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
2016-12-23 10:59:53 +02:00
Avichal Agarwal
318d4b5beb D-Bus: Add WPS manufacturer as property
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
2016-12-23 10:59:50 +02:00
Avichal Agarwal
b20f031c68 D-Bus: Add WPS device name as property
Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
2016-12-23 10:51:09 +02:00
Sunil Dutt
4a45dc1921 mesh: Show [MESH] flag in print_bss_info()
This was previously done for SCAN_RESULTS, but the BSS control interface
command did not show a similar flag. In addition, change "WPA2" to "RSN"
for mesh BSS to be consistent with the SCAN_RESULTS output.

Commit 638d945679 ('mesh: Show [MESH] flag
in scan results') did similar changes for SCAN_RESULTS.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-22 14:11:02 +02:00
Joel Cunningham
9187b13adb wpa_supplicant: Add BSS CURRENT control interface command
This commit extends the BSS commands to include "BSS CURRENT" as a way
to get the current BSS without having to walk the BSS list matching
against BSSID+SSID returned from the STATUS command.

This returns the BSS stored in wpa_s->current_bss.

Signed-off-by: Joel Cunningham <joel.cunningham@me.com>
2016-12-21 12:42:20 +02:00
Purushottam Kushwaha
a6f3761f7d eap_proxy: Add support for SIM state change indication from eap_proxy
This registers a new callback to indicate change in SIM state. This
helps to do some clean up (more specifically pmksa_flush) based on the
state change of the SIM. Without this, the reconnection using the cached
PMKSA could happen though the SIM is changed.

Currently eap_proxy_sim_state corresponds to only SIM_STATE_ERROR. This
can be further extended.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-19 22:21:07 +02:00
Amit Purwar
4e118c847b D-Bus: Add 'freq' option to P2P Find method to specify starting channel
This allows user to start P2P Find/Scan on a particular frequency and
then move to scanning social channels. This support is already present
on control socket.

Signed-off-by: Amit Purwar <amit.purwar@samsung.com>
2016-12-19 13:09:31 +02:00
Mikael Kanstrup
dfc7731729 Android: Add p2p_add_cli_chan=1 option
Add p2p_add_cli_chan=1 option to p2p_supplicant.conf to allow Wi-Fi P2P
operating as P2P client on passive scan channels.

In addition, add p2p_add_cli_chan=1 option to wpa_supplicant.conf to
have consistency in P2P channel list. There is a case where P2P channel
list is updated with different channels from p2p0 and wlan0.

Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
2016-12-18 17:56:17 +02:00
Badrish Adiga H R
7508c2ad99 PAE: Make KaY specific details available via control interface
Add KaY details to the STATUS command output.

Signed-off-by: Badrish Adiga H R <badrish.adigahr@hpe.com>
2016-12-18 17:47:05 +02:00
Jouni Malinen
b54f43390e FILS: Make FILS Indication element information available in BSS output
This extends wpa_supplicant BSS command to parse FILS Indication
element.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-18 11:41:59 +02:00
Jouni Malinen
9cad618679 FILS: Add Realm Information ANQP-element in BSS data
Add a named BSS command output entry for FILS Realm Information
ANQP-element (anqp_fils_realm_info).

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-18 11:41:51 +02:00
Jouni Malinen
aaa9c60bc2 Fix preauth_test build by updating add_pmkid/remove_pmkid callbacks
Commit c579312736 ('Add
PMKSA-CACHE-ADDED/REMOVED events to wpa_supplicant') added new arguments
to these callback functions, but forgot to update the implementations in
preauth_test.c.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-14 16:38:44 +02:00
Jouni Malinen
19810d29bc Make Beacon IEs available in wpa_supplicant BSS command
This makes both the Probe Response and Beacon frame IEs available to
upper layers if scan results include both IE sets. When the BSS command
mask includes WPA_BSS_MASK_BEACON_IE, a new beacon_ie=<hexdump> entry
will be included in output if the BSS entry has two separate sets of IEs
(ie=<hexdump> showing the Probe Response frame contents and
beacon_ie=<hexdump> the Beacon rame contents).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-13 20:07:52 +02:00
Jouni Malinen
274e76f22f mesh: Fix channel configuration in pri/sec switch case
If 20/40 MHz co-ex scan resulted in switching primary and secondary
channels, mesh setup failed to update the frequency parameters for
hostapd side configuration and that could result in invalid secondary
channel configuration preventing creating of the mesh network. This
could happen, e.g., when trying to set up mesh on 5 GHz channel 36 and
co-ex scan finding a BSS on channel 40. Switching the pri/sec channels
resulted in hostapd code trying to check whether channel 32 is
available. Fix this by swapping the channels for hostapd configuration
when needed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-13 15:25:52 +02:00
Jouni Malinen
3459381dd2 External persistent storage for PMKSA cache entries
This adds new wpa_supplicant control interface commands PMKSA_GET and
PMKSA_ADD that can be used to store PMKSA cache entries in an external
persistent storage when terminating a wpa_supplicant process and then
restore those entries when starting a new process. The previously added
PMKSA-CACHE-ADDED/REMOVED events can be used to help in synchronizing
the external storage with the memory-only volatile storage within
wpa_supplicant.

"PMKSA_GET <network_id>" fetches all stored PMKSA cache entries bound to
a specific network profile. The network_id of the current profile is
available with the STATUS command (id=<network_id). In addition, the
network_id is included in the PMKSA-CACHE-ADDED/REMOVED events. The
output of the PMKSA_GET command uses the following format:

<BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration in seconds>
<akmp> <opportunistic>

For example:

02:00:00:00:03:00 113b8b5dc8eda16594e8274df4caa3d4 355e98681d09e0b69d3a342f96998aa765d10c4459ac592459b5efc6b563eff6 30240 43200 1 0
02:00:00:00:04:00 bbdac8607aaaac28e16aacc9152ffe23 e3dd6adc390e685985e5f40e6fe72df846a0acadc59ba15c208d9cb41732a663 30240 43200 1 0

The PMKSA_GET command uses the following format:

<network_id> <BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration
in seconds> <akmp> <opportunistic>

(i.e., "PMKSA_ADD <network_id> " prefix followed by a line of PMKSA_GET
output data; however, the reauth_time and expiration values need to be
updated by decrementing them by number of seconds between the PMKSA_GET
and PMKSA_ADD commands)

For example:

PMKSA_ADD 0 02:00:00:00:03:00 113b8b5dc8eda16594e8274df4caa3d4 355e98681d09e0b69d3a342f96998aa765d10c4459ac592459b5efc6b563eff6 30140 43100 1 0
PMKSA_ADD 0 02:00:00:00:04:00 bbdac8607aaaac28e16aacc9152ffe23 e3dd6adc390e685985e5f40e6fe72df846a0acadc59ba15c208d9cb41732a663 30140 43100 1 0

This functionality is disabled be default and can be enabled with
CONFIG_PMKSA_CACHE_EXTERNAL=y build configuration option. It should be
noted that this allows any process that has access to the wpa_supplicant
control interface to use PMKSA_ADD command to fetch keying material
(PMK), so this is for environments in which the control interface access
is restricted.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-12 23:47:04 +02:00
Jouni Malinen
c579312736 Add PMKSA-CACHE-ADDED/REMOVED events to wpa_supplicant
These allow external program to monitor PMKSA cache updates in
preparation to enable external persistent storage of PMKSA cache.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-12 21:00:43 +02:00
Avichal Agarwal
5149a0f04c P2P: Set p2p_persistent_group=1 at the time of reading disabled=2
Configuration file network block with disabled=2 is used for storing
information about a persistent group, so p2p_persitent_group should be
updated according to this when creating a struct wpa_ssid instance. This
will end up using D-Bus persistent network object path for the network.

Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
Signed-off-by: Kyeong-Chae Lim <kcya.lim@samsung.com>
2016-12-12 20:30:31 +02:00
vamsi krishna
065c029a55 Remove MBO dependency from Supported Operating Classes element
Supported Operating Classes element and its use is define in the IEEE
802.11 standard and can be sent even when MBO is disabled in the build.
As such, move this functionality out from the CONFIG_MBO=y only mbo.c.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-11 22:07:58 +02:00
Jouni Malinen
a5c723adcf Interworking: Clear SCANNING state if no network selected
Commit 192ad3d730 ('Interworking: Clear
SCANNING state if no match found') did this for the case where no
network matched credentials, but left the SCANNING state in place if
there were a match, but automatic connection was not enabled. Extend
this to cover the case where INTERWORKING_SELECT is not followed by a
connection attempt so that wpa_state is not left indefinitely to
SCANNING.

This fixes a hwsim test case failure in the following sequence:
ap_anqp_sharing scan_trigger_failure

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-11 18:39:12 +02:00
Jouni Malinen
a1836de64b SME: Fix IBSS setup after shared key/FT/FILS association
wpa_s->sme.auth_alg could have been left to a previously value other
than WPA_AUTH_ALG_OPEN if IBSS network is used after an association that
used shared key, FT, or FILS authentication algorithm. This could result
in the IBSS setup failing due to incorrect authentication processing
steps.

Fix this by setting wpa_s->sme.auth_alg = WPA_AUTH_ALG_OPEN whenever
starting an IBSS (or mesh, for that matter) network.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-11 18:23:13 +02:00
Amit Purwar
f49c852b5e P2P: Fix a theoretical out of bounds read in wpas_p2p_select_go_freq()
Commit 8e84921efe ('P2P: Support driver
preferred freq list for Autonomous GO case') introduced this loop to go
through preferred channel list from the driver. The loop does bounds
checking of the index only after having read a value from the array.
That could in theory read one entry beyond the end of the stack buffer.

Fix this by moving the index variable check to be done before using it
to fetch a value from the array.

This code is used only if wpa_supplicant is build with
CONFIG_DRIVER_NL80211_QCA=y and if the driver supports the vendor
extension (get_pref_freq_list() driver op). In addition, the driver
would need to return more than P2P_MAX_PREF_CHANNELS (= 100) preferred
channels for this to actually be able to read beyond the buffer. No
driver is known to return that many preferred channels, so this does not
seem to be reachable in practice.

Signed-off-by: Amit Purwar <amit.purwar@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
2016-12-11 12:45:08 +02:00
Amit Purwar
944d485889 P2P: Fix a theoretical out of bounds read in wpas_p2p_setup_freqs()
Commit 370017d968 ('P2P: Use preferred
frequency list from the local driver') introduced this loop to go
through preferred channel list from the driver. The loop does bounds
checking of the index only after having read a value from the array.
That could in theory read one entry beyond the end of the stack buffer.

Fix this by moving the index variable check to be done before using it
to fetch a value from the array.

This code is used only if wpa_supplicant is build with
CONFIG_DRIVER_NL80211_QCA=y and if the driver supports the vendor
extension (get_pref_freq_list() driver op). In addition, the driver
would need to return more than P2P_MAX_PREF_CHANNELS (= 100) preferred
channels for this to actually be able to read beyond the buffer. No
driver is known to return that many preferred channels, so this does not
seem to be reachable in practice.

Signed-off-by: Amit Purwar <amit.purwar@samsung.com>
Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
2016-12-11 12:45:08 +02:00
Jouni Malinen
6e374bd44d Ignore scan results from ongoing scan when FLUSH command is issued
This makes wpa_supplicant behavior more consistent with FLUSH command to
clear all state. Previously, it was possible for an ongoing scan to be
aborted when the FLUSH command is issued and the scan results from that
aborted scan would still be processed and that would update the BSS
table which was supposed to cleared by the FLUSH command.

This could result in hwsim test case failures due to unexpected BSS
table entries being present after the FLUSH command.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-11 12:45:08 +02:00
Jouni Malinen
71ac934530 Make update_idx available in BSS control interface command
This can be used to perform more accurate tests on BSS entry updates.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-10 17:03:24 +02:00
Jouni Malinen
5ec3d510e1 wpa_passphrase: Reject invalid passphrase
Reject a passphrase with control characters instead of trying to write
out an example network configuration block with such control characters
included.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-12-05 15:36:56 +02:00
Arik Nemtsov
57f93d6889 Defer scans while PNO is in progress instead of skipping them
Skipping the scan altogether will hurt auto-reconnect. Also move the PNO
check down since the scan might be canceled for other reasons before we
defer it.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2016-12-04 20:27:06 +02:00
Jouni Malinen
cfadab269f nl80211: Move duplicate scan result removal to bss.c
The way the removal of duplicated (one per frequency) BSS entries in the
cfg80211 scan results were removed in driver_nl80211_scan.c
bss_info_handler() depended on having the full scan results available to
allow iteration through the other entries. This is problematic for the
goal of being able to optimize memory allocations for scan result
fetching in a manner that would not build the full result buffer in
memory.

Move this duplicate removal into bss.c since it has sufficient
information available for doing the same determination of which one of
two BSS entries is more current.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-03 19:26:47 +02:00
Jouni Malinen
865081c307 privsep: Support frequency list for scan requests
Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-03 18:27:16 +02:00
Jouni Malinen
da818ee5e9 privsep: Support multiple scan SSIDs
Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-03 18:17:28 +02:00
Jouni Malinen
d3c43e5855 privsep: Fix scan result fetching with Beacon frame IEs
wpa_priv did not yet support Beacon frame IEs (res->beacon_ie_len) which
resulted in invalid scan data being accepted in driver_privsep.c. Add
support for res->beacon_ie_len and also fix the validation step to take
this new variable length field into account.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-03 18:02:49 +02:00
Jouni Malinen
0771e912ae wpa_priv: Document reduced functionality
wpa_priv has never really been fully up-to-date with the wpa_supplicant
driver interface extensions. This does not seem like something that
would change in the future either, so document this reduced
functionality as a potential drawback.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-03 17:49:37 +02:00
Jouni Malinen
6d97561dcd wpa_priv: Handler driver global_deinit() on termination path
This avoids a theoretical resource leak on exit path if wpa_priv is
killed while there is a wpa_supplicant process using it.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-03 17:46:08 +02:00
Jouni Malinen
ce0f899a3d wpa_priv: Explicitly clear padding in message structures
This avoids some valgrind warnings about use of uninitialized memory in
cases where a struct may have padding octets between the fields.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-03 17:46:08 +02:00
Jouni Malinen
e0641772a3 wpa_priv: Use fromlen instead sizeof(struct sockaddr_un)
This gets rid of some dependencies on how extra octets at the end of the
struct sockaddr_un get "uninitialized" consistently by only using the
exact length of the address data from the recvfrom() call. This resolves
number of valgrind warnings about use of uninitialized memory.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-03 17:28:18 +02:00
Jouni Malinen
128d3c69fc wpa_priv: Add support for multiple l2_packet connections
This is needed to be able to work with many wpa_supplicant use cases,
e.g., due to use of TDLS or RSN pre-authentication needing a separate
l2_packet socket.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-03 11:37:41 +02:00
Sabrina Dubroca
ba5ea11687 mka: Remove references to macsec_qca from wpa_supplicant.conf
Make the documentation generic, as this is no longer the only macsec
driver.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-11-30 20:08:39 +02:00
Sunil Dutt
bf88401d23 Add support to abort vendor scan
This commit enhances the existing implementation of abort scan to also
abort concurrent active vendor scans. This is achieved by passing the
the scan_cookie to the driver interface with the intention to abort
the specific scan request. This scan_cookie is returned from the driver
interface when the scan request is scheduled.

This scan_cookie is 0 if the scan is triggered through the upstream
cfg80211 interface. Thus, the scan_cookie is used to determine whether
to abort the cfg80211 or vendor scan request.

Also, the previous implementation of relying on scan_work/p2p_scan_work
for the active work to trigger the abort scan is enhanced to check for
the started state of either of these work operations. This should also
help to abort the concurrent active scan/p2p-scan operations.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-11-30 19:33:43 +02:00
Sunil Dutt
eeb34a432e nl80211: Enhance abort scan to also abort the vendor scan
This commit enhances the abort scan implementation to also abort the
vendor scan, if one was used to trigger the scan.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-11-30 19:33:39 +02:00
Srinivas Dasari
346b333d9a Use random MAC address for scanning only in non-connected state
cfg80211 rejects the scans issued with random MAC address if the STA is
in connected state. This resulted in failures when using MAC_RAND_SCAN
while connected (CTRL-EVENT-SCAN-FAILED ret=-95). Enable random MAC
address functionality only if the STA is not in connected state to avoid
this. The real MAC address of the STA is already revealed in the
association, so this is an acceptable fallback mechanism for now.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-11-25 22:52:39 +02:00
Nishant Chaprana
18f1611797 D-Bus: Send P2P IP address assignment info with GroupStarted event
This commit adds IP address information into GroupStarted event on the
P2P client side like it is sent over the control interface.

Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2016-11-21 14:45:13 +02:00
Nishant Chaprana
046fa6fd11 D-Bus: Add getter and setter for P2P IP address config parameters
This patch adds setter and getter for P2P IP address config parameters:
1. ip_addr_go
2. ip_addr_mask
3. ip_addr_start
4. ip_addr_end

Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2016-11-20 12:41:39 +02:00
Sabrina Dubroca
e0d9fd344d wpa_supplicant: Allow configuring the MACsec port for MKA
Previously, wpa_supplicant only supported hardcoded port == 1 in the
SCI, but users may want to choose a different port.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-11-20 00:35:31 +02:00
Sabrina Dubroca
1d3d0666a6 mka: Add enable_encrypt op and call it from CP state machine
This allows MKA to turn encryption on/off down to the driver.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-11-20 00:35:23 +02:00
Sabrina Dubroca
7b4d546e3d wpa_supplicant: Add macsec_integ_only setting for MKA
So that the user can turn encryption on (MACsec provides
confidentiality+integrity) or off (MACsec provides integrity only). This
commit adds the configuration parameter while the actual behavior change
to disable encryption in the driver is handled in the following commit.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-11-20 00:35:16 +02:00
Sabrina Dubroca
ad51731abf wpa_supplicant: Allow pre-shared (CAK,CKN) pair for MKA
This enables configuring key_mgmt=NONE + mka_ckn + mka_cak.
This allows wpa_supplicant to work in a peer-to-peer mode, where peers
are authenticated by the pre-shared (CAK,CKN) pair. In this mode, peers
can act as key server to distribute keys for the MACsec instances.

This is what some MACsec switches support, and even without HW
support, it's a convenient way to setup a network.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-11-20 00:35:08 +02:00
Kenny Root
88f93c30ec Android: Remove BoringSSL guard
BoringSSL is the only supported version of SSL, so remove this guard so
we can continue to compile when the flavor.mk is removed.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2016-11-19 17:43:03 +02:00
Jouni Malinen
e65a87b399 Debug print scan results matching the currently selected network
This provides more details on BSS selection process in the debug log.
Previously, the BSSs that were not either the current or the selected
one were not necessarily printed at all. Now all BSSs that match the
currently selected network are listed with their frequency and signal
strength details.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-11-13 18:22:38 +02:00
Jouni Malinen
8d1e693186 Use estimated throughput to avoid signal based roaming decision
Previously, the estimated throughput was used to enable roaming to a
better AP. However, this information was not used when considering a
roam to an AP that has better signal strength, but smaller estimated
throughput. This could result in allowing roaming from 5 GHz band to 2.4
GHz band in cases where 2.4 GHz band has significantly higher signal
strength, but still a lower throughput estimate.

Make this less likely to happen by increasing/reducing the minimum
required signal strength difference based on the estimated throughputs
of the current and selected AP. In addition, add more details about the
selection process to the debug log to make it easier to determine whaty
happened and why.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-11-13 17:52:32 +02:00
Ilan Peer
4ec1fd8e42 FT: Differentiate between FT for station and for AP in build
Previously, CONFIG_IEEE80211R enabled build that supports FT for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode FT is required and there is no need for AP mode FT.

Add support to differentiate between station mode FT and AP mode FT in
wpa_supplicant builds by adding CONFIG_IEEE80211R_AP that should be used
when AP mode FT support is required in addition to station mode FT. This
allows binary size to be reduced for builds that require only the
station side FT functionality.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2016-10-29 22:14:54 +03:00
Avrahams Stern
c433c50c9c wpa_supplicant: Make CONFIG_MBO independent of CONFIG_AP
CONFIG_MBO was defined inside ifdef CONFIG_AP, so when AP support
was not compiled, MBO was not compiled either. However, CONFIG_MBO
is not related AP support, so it should not depend on CONFIG_AP.

Fix this by moving CONFIG_MBO outside of ifdef CONFIG_AP.

Signed-off-by: Avrahams Stern <avraham.stern@intel.com>
2016-10-29 19:31:38 +03:00
Eliad Peller
d044d2f7d8 wpa_supplicant: Get scan_result IE also from Beacon frames
No reason to require ie_len if only beacon_ie_len is given.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2016-10-29 19:28:37 +03:00