The CAK length is not hardcoded in the algorithm agility parameter, so
remove that from the table. Instead, allow both 16 (128-bit) and 32
(256-bit) CAK to be used so that the following key derivations use
appropriate key lengths based on the configured/derived CAK.
Signed-off-by: Jouni Malinen <j@w1.fi>
The ICK and KEK are derived from a CAK and the length of the CAK
determines the length of the KCK/ICK. Remove the separate ICK/KEK length
parameters from the algorithm agility table.
Signed-off-by: Jouni Malinen <j@w1.fi>
Extend the previously implemented KDF (IEEE Std 802.1X-2010, 6.2.1) to
support 256-bit input key and AES-CMAC-256. This does not change any
actual key derivation functionality yet, but is needed as a step towards
supporting 256-bit CAK.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible to get a situation where a peer removes the Key Server
from its live peers list but the server still thinks that the peer is
alive (e.g., high packet loss in one direction). In such a case, the Key
Server will continue to advertise Last Key but this peer will not be
able to set up SA as it has already deleted its key.
Change the peer MI which will force the Key Server to distribute a new
SAK.
Signed-off-by: Andrey Kartashev <andrey.kartashev@afconsult.com>
Decrease timeout for a peer with duplicated SCI to speed up process in
case it is a valid peer after MI change.
Signed-off-by: Andrey Kartashev <andrey.kartashev@afconsult.com>
There is already partial support of GCM-AES-256. It is possible to
enable this mode by setting 'kay->macsec_csindex = 1;' in
ieee802_1x_kay_init() function, but the generated key contained only 128
bits of data while other 128 bits are in 0.
Enables KaY to generate full 256-bit SAK from the same 128-bit CAK. Note
that this does not support 256-bit CAK or AES-CMAC-256 -based KDF.
Signed-off-by: Andrey Kartashev <andrey.kartashev@afconsult.com>
According IEEE Std 802.1X-2010, 9.8 each participant shall record the
values of NextPN for last SAK accepted from each Key Server to use it in
case of a switch from one Key Server to another and back. Add LPN
recording and set saved value as the initial PN for the created channel.
Signed-off-by: Andrey Kartashev <andrey.kartashev@afconsult.com>
It is possible that the driver fails to create Secure Channel (due to
hardware limitations for example). Add checks of create_*_sc() result
codes and abort procedure in case of failure.
Signed-off-by: Andrey Kartashev <andrey.kartashev@afconsult.com>
Fix a minor memory leak in ieee802_1x_kay_create_mka() in
case of KEK/ICK derivation failure.
Signed-off-by: Andrey Kartashev <andrey.kartashev@afconsult.com>
Add new configuration parameters macsec_replay_protect and
macsec_replay_window to allow user to set up MACsec replay protection
feature. Note that according to IEEE Std 802.1X-2010 replay protection
and delay protection are different features: replay protection is
related only to SecY and does not appear on MKA level while delay
protection is something that KaY can use to manage SecY state.
Signed-off-by: Andrey Kartashev <andrey.kartashev@afconsult.com>
When syslog logging is used output from wpa_hexdump_ascii() was silently
discarded. This patch enables wpa_hexdump_ascii() to print data to
syslog but without ASCII decoding.
Signed-off-by: Andrey Kartashev <andrey.kartashev@afconsult.com>
To prevent a remote peer from getting stuck in a perpetual 'potential
peer' state, only update the peer liveness timer 'peer->expire' for live
peers and not for potential peers.
Per IEEE Std 802.1X-2010, 9.4.3 (Determining liveness), potential peers
need to show liveness by including our MI/MN in their transmitted MKPDU
(within potential or live parameter sets).
When a potential peer does include our MI/MN in an MKPDU, we respond by
moving the peer from 'potential_peers' to 'live_peers'.
If a potential peer does not include our MI/MN in an MKPDU within
MKPDU_LIFE_TIME, let the peer expire to facilitate getting back in sync
with the remote peer.
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
The previous commit introduced parameter set error checking. This commit
extends upon that by considering missing parameter sets a failure.
Two checks are added by this commit. First, verify that live peers start
encoding MKA_SAK_USE within a reasonable amount of time after going live
(10 MKPDUs). Second, verify that once a live peer starts encoding
MKA_SAK_USE it continues to do so indefinitely.
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
The status values returned by mka_param_body_handler.body_rx functions
are currently ignored by ieee802_1x_kay_decode_mkpdu(). If a failure is
detected the KaY should (a) stop processing the MKDPU and (b) do not
update the associated peer's liveliness.
IEEE Std 802.1X-2010, Table 11-7 (MKPDU parameter sets) and 11.11.3
(Encoding MKPDUs) dictate that MKA_SAK_USE (set type 3) will always be
encoded before MKA_DISTRIBUTED_SAK (set type 4) in MKPDUs. Due to
implementation of mka_param_body_handler, the code will always decode
MKA_SAK_USE before MKA_DISTRIBUTED_SAK. When MKA_DISTRUBUTED_SAK
contains a new SAK the code should decode MKA_DISTRUBUTED_SAK first so
that the latest SAK is in known before decoding MKA_SAK_USE.
The ideal solution would be to make two passes at MKDPU decoding: the
first pass decodes MKA_DISTRIBUTED_SAK, the second pass decodes all
other parameter sets.
A simpler and less risky solution is presented here: ignore MKA_SAK_USE
failures if MKA_DISTRIBUTED_SAK is also present. The new SAK will be
saved so that the next MKPDU's MKA_SAK_USE can be properly decoded. This
is basically what the code prior to this commit was doing (by ignoring
all errors).
Also, the only real recourse the KaY has when detecting any bad
parameter set is to ignore the MKPDU by not updating the corresponding
peer's liveliness timer, 'peer->expire'.
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
If a live peer ever changes its Member Identifier (MI), the KaY
correctly detects a "duplicated SCI" but then proceeds to delete the
peer without deleting the peer's resources (i.e., RxSC, RxSAs, TxSAs).
Note that a remote peer's MI will change if and when an
ieee8021XPaePortInitialize is executed on the remote port.
The solution here is to ignore all MKPDUs containing the new MI until
after the peer (that corresponds to the old MI) expires and cleans up
its resources. After the old peer is removed reception of the next MKPDU
containing the new MI will result in the creation of a new peer with the
new MI.
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
Per IEEE Std 802.1X-2010, Figure 12-2 (CP state machine), READY to
TRANSMIT transition includes !controlledPortEnabled condition.
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
Per IEEE Std 802.1X-2010, Figure 12-2 (CP state machine), READY should
move to ABANDON (not RECEIVE) when new_sak or changed_connect is true.
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
Per IEEE Std 802.1X-2010, Figure 12-2 (CP state machine), RECEIVING to
TRANSMIT transition includes !controlledPortEnabled condition.
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
Per IEEE Std 802.1X-2010, Figure 12-2 (CP state machine), deleteSAs(oki)
is used upon entering RETIRE. Do that in addition to freeing sm->oki.
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
The purpose of the Lowest Acceptable PN (lpn) parameters in the MACsec
SAK Use parameter set is to enforce delay protection. Per IEEE Std
802.1X-2010, Clause 9, "Each SecY uses MKA to communicate the lowest PN
used for transmission with the SAK within the last two seconds, allowing
receivers to bound transmission delays."
When encoding the SAK Use parameter set the KaY should set llpn and olpn
to the lowest PN transmitted by the latest SAK and oldest SAK (if
active) within the last two seconds. Because MKPDUs are transmitted
every 2 seconds (MKA_HELLO_TIME), the solution implemented here
calculates lpn based on the txsc->next_pn read during the previous MKPDU
transmit.
Upon receiving and decoding a SAK Use parameter set with delay
protection enabled, the KaY will update the SecY's lpn if the delay
protect lpn is greater than the SecY's current lpn (which is a product
of last PN received and replay protection and window size).
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
Delay Protect and Replay Protect are two separate and distinct features
of MKA. Per IEEE Std 802.1X-2010, 9.10.1 "Delay Protect, TRUE if LPNs
are being reported sufficiently frequently to allow the recipient to
provide data delay protection. If FALSE, the LPN can be reported as
zero", and per 9.10 "NOTE--Enforcement of bounded received delay
necessitates transmission of MKPDUs at frequent (0.5 s) intervals, to
meet a maximum data delay of 2 s while minimizing connectivity
interruption due to the possibility of lost or delayed MKPDUs."
This means struct ieee802_1x_mka_sak_use_body::delay_protect should only
be set TRUE when MKPDUs are being transmitted every 0.5 s (or faster).
By default the KaY sends MKPDUs every MKA_HELLO_TIME (2.0 s), so by
default delay_protect should be FALSE.
Add a new 'u32 mka_hello_time' parameter to struct ieee802_1x_kay. If
delay protection is desired, the KaY initialization code should set
kay->mka_hello_time to MKA_BOUNDED_HELLO_TIME (500 ms).
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
Commit 7b4d546e ("wpa_supplicant: Add macsec_integ_only setting for
MKA") introduced policy setting SHOULD_ENCRYPT (MACsec provides
integrity+confidentiality) in addition to SHOULD_SECURE (MACsec provides
integrity only). In both cases the KaY is populating the
"Confidentiality Offset" parameter within the "Distributed SAK parameter
set" with CONFIDENTIALITY_OFFSET_0=1. In the case of SHOULD_SECURE the
parameter should be populated with CONFIDENTIALITY_NONE=0.
IEEE Std 802.1X-2010, Table 11-6 and Figure 11-11 define how the two
Confidentiality Offset bits in the "Distributed SAK parameter set" must
be set: "0 if confidentiality not used" and "1 if confidentiality with
no offset". When policy is SHOULD_SECURE KaY should to send the former,
and when policy is SHOULD_ENCRYPT KaY should send the latter.
Fixes: 7b4d546e3d ("wpa_supplicant: Add macsec_integ_only setting for MKA")
Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
IEEE Std 802.1X-2010, 9.3.1 defines following restrictions for CKN:
"MKA places no restriction on the format of the CKN, save that it comprise
an integral number of octets, between 1 and 32 (inclusive), and that all
potential members of the CA use the same CKN. No further constraints are
placed on the CKNs used with PSKs, ..."
Hence do not require a 32 octet long CKN but instead allow a shorter CKN
to be configured.
This fixes interoperability with some Aruba switches, that do not accept
a 32 octet long CKN (only support shorter ones).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
IEEE Std 802.1X-2010, Figure 11-7 explains that "Parameter set body
length" is exclusive of the suffix padding.
Fix variable length encoding and decoding when CKN length is not a
multiple of 4 bytes.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Mark the data structures used in construction/parsing frames packed to
prevent compiler from being able to pad them.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_supplicant STATUS-DRIVER control interface command can now be used
to fetch the macsec_linux driver status information like parent
interface name.
Signed-off-by: Jouni Malinen <j@w1.fi>
Not all driver interfaces provide driver status information with the
local address, so skip the override step if the field is not available.
This is needed, e.g., with macsec_linux.
Signed-off-by: Jouni Malinen <j@w1.fi>
These do not really get truncated in practice, but it looks like some
newer compilers warn about the prints, so silence those by checking the
result and do something a bit more useful if the output would actually
get truncated.
Signed-off-by: Jouni Malinen <j@w1.fi>
Addi a readme file for users for on-boarding devices with Device
Provisioning Protocol (DPP).
Signed-off-by: Rohit Damodaran <Rohit_Damodaran@comcast.com>
Make it possible to list connected stations in AP mode over D-Bus, along
with some of their properties: rx/tx packets, bytes, capabilities, etc.
Signed-off-by: Mathieu Trudel-Lapierre <mathieu.trudel-lapierre@canonical.com>
Rebased by Julian Andres Klode <juliank@ubuntu.com> and updated to use
the new getter API.
Further modified by Andrej Shadura to not error out when not in AP mode
and to send separate StationAdded/StationRemoved signals instead of
changing signatures of existing StaAuthorized/StaDeauthorized signals.
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Properties argument specifies whether to add object's properties
or not, hence it doesn't need to be int.
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Add a new test to check that the AP won't send frames to the client if
it tries to talk to itself.
Note that this fails until the relevant mac80211 patch is merged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These test cases seemed to have copy-paste errors where
wait_enabled=False was forgotten even though there was no additional
steps checking the AP mode startup results. This did not break the
tests, but could have resulted in slowing them down if the STAs did not
find the AP in the first scan.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow user to override STBC configuration for Rx and Tx spatial streams.
Add new configuration options to test for HT capability overrides.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
The Linux kernel commit 113f3aaa81bd ("cfg80211: Prevent regulatory
restore during STA disconnect in concurrent interfaces") broke the
regulatory clearing attempt in many test cases since
cfg80211_is_all_idle() is now returning false due to the AP interface
being up and that results in the Country IE -based regulatory
information not getting cleared back to defaults.
Work around this by stopping the AP interface first so that when the
station interface receives the disconnection, there are no other active
interfaces in the system. In addition, wait for REGDOM event for the
Country IE hint after association to avoid disconnection before the
regulatory events have been fully processed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Linux kernel commit 113f3aaa81bd ("cfg80211: Prevent regulatory
restore during STA disconnect in concurrent interfaces") broke the
regulatory clearing attempt in this test case since
cfg80211_is_all_idle() is now returning false due to the AP interface
being up and that results in the Country IE -based regulatory
information not getting cleared back to defaults.
Work around this by stopping the AP interface first so that when the
station interface receives the disconnection, there are no other active
interfaces in the system. In addition, wait for REGDOM event for the
Country IE hint after association to avoid disconnection before the
regulatory events have been fully processed.
Signed-off-by: Jouni Malinen <j@w1.fi>
