The new hostapd ctrl_iface command WPS_NFC_TOKEN can now be used to
manage AP-as-Enrollee operations with NFC password token. WPS/NDEF
parameters to this command can be used to generate a new NFC password
token. enable/disable parameters can be used to enable/disable use of
NFC password token (instead of AP PIN) for external Registrars.
A preconfigured NFS password token can be used by providing its
parameters with new hostapd.conf fields wps_nfc_dev_pw_id,
wps_nfc_dh_pubkey, wps_nfc_dh_privkey, and wps_nfc_dev_pw. This use
will also depend on WPS_NFC_TOKEN enable/disable commands, i.e., the
configured NFS password token is disabled by default.
Signed-hostap: Jouni Malinen <j@w1.fi>
The AP PIN on wps_reg command can now be replaced with special value
"nfc-pw" to use device password from a NFC password token from the AP.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPS_ER_NFC_CONFIG_TOKEN command can now be used to build a NFC
configuration token based on AP Settings learnt with WPS_ER_LEARN
or set with WPS_ER_CONFIG.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new wpa_supplicant ctrl_iface command WPS_NFC_TAG_READ can now be
used to process NFC tags read by external programs to initiate
wpa_supplicant to use NFC Configuration Token to create a new network.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new hostapd ctrl_iface command WPS_NFC_CONFIG_TOKEN can now be used
to fetch payload for an NFC configuration token so that an external
program can be used to write this on an NFC tag.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds a cleaner mechanism for handling NFC Password Tokens in the
WPS Registrar. There could be more than one active NFC Password Token in
use and as such, a list of tokens needs to be maintained. The old
WPS_OOB interface is still using the old mechanism that supports only a
single active NFC Password Token.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd ctrl_iface can now be used to deliver payload from read
operation of an NFC tag. This allows operations without having to have
low-level NFC code within hostapd. For now, the new wps_nfc_tag_read
command can be used with NFC password tokens for the case where the AP
has an NFC device that is used to read an NFC tag from the station
Enrollee.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of requiring low-level access to an NFC device and synchronous
operations, the new WPS_NFC_TOKEN and WPS_NFC ctrl_iface commands can be
used to build a NFC password token and initiate WPS protocol run using
that token (or pre-configured values) as separate commands. The
WPS_NFC_TOKEN output can be written to a NFC tag using an external
program, i.e., wpa_supplicant does not need to have low-level code for
NFC operations for this.
Signed-hostap: Jouni Malinen <j@w1.fi>
The OOB Device Password is passed in as a hexdump of the real Device
Password (16..32 octets of arbitrary binary data). The hexdump needs to
be converted to binary form before passing it for WPS processing.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, only the maximum length 32 octets for OOB device password
was accepted. Since the specification allows a shorter password to be
used with limited OOB mechanism (e.g., small NFC tag), we should accept
lengths 16..32.
Signed-hostap: Jouni Malinen <j@w1.fi>
The earlier WPS 2.0 changes did not increase the wpabuf size when
adding a new attribute to the NFC password token. This could result
in aborting the application on wpabuf overflow if NFC out-of-band
mechanism is used with WPS 2.0 enabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Some drivers may independently decide to switch channels. Handle this by
updating the hostapd and wpa_supplicant AP and GO configuration.
Signed-hostap: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Previously, the STA entry was removed only from the driver and the STA
entry within hostapd was just marked disassociated. However, this left
the WPA authenticator state machine with an entry and the session was
not terminated properly. In addition, the STA entry could have remaining
indefinitely if the STA did not reconnect after TKIP countermeasures.
Fix this by removing the STA entry from hostapd instead of just leaving
it disassociated.
Signed-hostap: Jouni Malinen <j@w1.fi>
In AP which supports WPSv2 with only virtual push button, when PBC is
called, the WSC IE should include Selected Registrar Configuration
Methods attribute with the bit of the physical push button not set.
Signed-hostap: Yoni Divinsky <yoni.divinsky@ti.com>
Without this, we can get into a tight loop because the
code in general doesn't add eloop exception handlers,
so socket reporting the POLLERR would never be read.
With this change, any socket with POLLERR or POLLHUP
asserted will be handled by the read logic.
Signed-hostap: Ben Greear <greearb@candelatech.com>
The control message received from the kernel needs some space, but
there's no need for the strange typing that breaks clang compilation.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Maintain a copy of Chargeable-User-Identity in the PMKSA cache to allow
it to be included in accounting messages even if full authentication was
not completed.
Signed-hostap: Jouni Malinen <j@w1.fi>
Calling-Station-Id, Acct-Session-Id, and User-Name attributes in a
Disconnect-Request message can now be used to indicate which station is
to be disconnected.
Signed-hostap: Jouni Malinen <j@w1.fi>
DAS will now validate Event-Timestamp value to be within an acceptable
time window (300 seconds by default; can be set using
radius_das_time_window parameter). In addition, Event-Timestamp can be
required in Disconnect-Request and CoA-Request messages with
radius_das_require_event_timestamp=1.
Signed-hostap: Jouni Malinen <j@w1.fi>
Currently, FullMAC Persistent GO can't use p2p_client_list because its
own hapd->p2p_group is NULL at ap_sta_set_authorized(). This patch
changes the processing to use sta->p2p_ie instead of
p2p_group_get_dev_addr() on FullMAC GO.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
The P2P Client Discoverability bit is reserved in most frames and its
value in the local P2P peer table should only be updated based on P2P
Group Info attribute from a GO. Fix this by avoiding changes to this
dev_capab bit based on other P2P frames. It would be more correct to
track this separately for each group in which the peer is a member, but
since we do not do that for the other group specific information either,
this can do for now.
It should be noted that prior to commit
18485b5469 wpa_supplicant set this bit in
all P2P frames. However, that commit changed this to match the
specification, i.e., the bit is not set in frames which are received
from P2P Device role. As such, this fix is needed to be able to figure
out that a peer supports client discoverability capability after that
commit.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
In the P2P specification v1.1, the P2P Client Discoverability bit is
described in Table 12 "Device Capability Bitmap definition". The table
says "Within a P2P Group Info attribute and a (Re)association request
frame the P2P Client Discoverability field shall be set to 1 when the
P2P Device supports P2P Client Discoverability, and is set to 0
otherwise. This field shall be reserved and set to 0 in all other frames
or uses.". To match with this, filter out P2P Client Discoverability bit
from frames where its use is reserved.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
If the peer uses an unknown reauth id, it would still be possible to use
pseudonym instead of permanent id. Allow this by changing the
AT_PERMANENT_ID_REQ to AT_FULLAUTH_ID_REQ in case unknown reauth id is
used in EAP-Response/Identity.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There is a race condition in GO Negotiation Request frame sending and
processing that may end up with both devices sending GO Negotiation
Response. This response frame was previously accepted even if a response
had already been sent. This could result in two GO Negotiation Confirm
frames being exchanged and consequently, with two separate GO
Negotiations completing concurrently. These negotiations could result in
getting mismatching parameters (e.g., both device could believe it was
the GO).
Fix this by ignoring GO Negotiation Response from the peer if twe have
already sent a GO Negotiation Response frame and we have the higher P2P
Device Address. This is similar to the rule used to determine whether to
reply to GO Negotiation Request frame when Request was already sent,
i.e., the same direction of GO Negotiation is maintained here to enforce
that only the negotiation initiated by the device with smaller P2P
Device Address is completed.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
If both peers initiate GO Negotiation at about the same time, it is
possible for the GO Negotiation Request frame from the peer to be
received between the local attempt to send the GO Negotiation Request
and TX status event for that. This could result in both devices sending
GO Negotiation Response frames even though one of them should have
skipped this based which device uses a higher MAC address.
Resolve this race by incrementing go_neg_req_sent when p2p_send_action()
returns success instead of doing this from the TX status callback. If
the frame is not acknowledged, go_neg_req_sent is cleared in TX status
handler.
Signed-off-by: Neeraj Garg <neerajkg@broadcom.com>
Stop the connection attempt if GO Negotiation Confirm is not received
within 100 ms of the GO Negotiation Response getting acknowledged.
Previously, we would have continued trying to connect to the peer even
in this case which could result in confusing second GO Negotiation
Request frame and unnecessarily long wait before indicating failure.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The GO Negotiation Confirm frame doesn't need to be sent with a wait
since we don't expect a response to it.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Concurrent Operation bit was not set for GO even if the device
supports concurrent operations. Make sure the Device Capability
value is consistent with other P2P use cases by using the value
determined in p2p_init().
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Send an "EAP" signal via the new DBus interface under various
conditions during EAP authentication:
- During method selection (ACK and NAK)
- During certificate verification
- While sending and receiving TLS alert messages
- EAP success and failure messages
This provides DBus callers a number of new tools:
- The ability to probe an AP for available EAP methods
(given an identity).
- The ability to identify why the remote certificate was
not verified.
- The ability to identify why the remote peer refused
a TLS connection.
Signed-hostap: Paul Stewart <pstew@chromium.org>
In certain cases like PBC session overlap it appears to be possible that
an interface is removed due to an event handled on it, this leads to
list corruption. Use safe iteration to prevent this issue.
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Reported-by: Neeraj Kumar Garg <neerajkg@broadcom.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
intended-for: hostap-1
When hostapd (or wpa_supplicant AP mode) limits the maximum number
of STA entries with a driver that implements SME, the driver needs
to be notified of the failed STA addition. Disassociate the STA if
the driver notifies of an association that would go beyond the
maximum number of STAs.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If WNM is enabled for the build (CONFIG_WNM=y), add BSS max idle period
information to the (Re)Association Response frame from the AP and parse
this information on the station. For SME-in-wpa_supplicant case, add a
timer to handle periodic transmission of the keep-alive frame. The
actual request for the driver to transmit a frame is not yet
implemented.
Signed-hostap: Jouni Malinen <j@w1.fi>
When sending an offchannel frame (mainly, P2P Invitation Request), the
wait_time parameter was hardcoded to 0 for drivers that implement AP
mode SME. This is not correct and can cause problems for drivers that
support offloading of off-channel operations with driver/firmware based
AP SME.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is a workaround for interoperability issues with some deployed P2P
implementations that require a Provision Discovery exchange to be used
before GO Negotiation. The new provdisc parameter for the p2p_connect
command can be used to request this behavior without having to run a
separate p2p_prov_disc command.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The nl80211 driver interface does not allow 128-bit WEP to be used
without a vendor specific cipher suite and no such suite is defined for
this purpose. Do not accept WEP key length 16 for nl80211 driver
interface forn ow. wext-interface can still try to use these for
backwards compatibility.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the AP indicates support for Hotspot 2.0, show this in the
ctrl_iface commands for BSS table and status.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If PD Request includes P2P Group ID, verify that the specified
group matches with a group we are currently operating. If no match
is found, reject the PD Request for join-a-group case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This can be used with P2P management operations that need to verify
whether the local device is operating a specific group based on
P2P Group ID attribute from a peer.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 349b213cc8 added a separate
callback prov_disc_fail() for indicating PD failures, but it left the
Provision Discovery Response handler to call both callbacks in case the
peer rejected the PD. Commit f65a239ba4
added ctrl_iface event for PD failures. This combination can result in
two ctrl_iface events in the peer rejecting a PD case. Clean this up by
only indicating the failure event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Some drivers may accept the remain-on-channel command, but instead of
indicating start event for remain-on-channel, just indicate that the
operation has been canceled immediately. This could result in continuous
loop of search/listen states with very limited time to do anything else
in wpa_supplicant if the scan command is also completed quickly (e.g.,
if the driver is unable to scan other channels than the current
operating channel).
As a workaround, do not start the next step (search) in P2P device
discovery if this type of rejection of listen operation is detected.
This gives some more time for wpa_supplicant to handle whatever else
may be needed at to be done at the same time and reduces the amount
of CPU used in a loop that does not really work correctly from the
view point of being discoverable.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
This adds the basic DAS mechanism to enable hostapd to be configured
to request dynamic authorization requests (Disconnect-Request and
CoA-Request). This commit does not add actual processing of the
requests, i.e., this will only receive and authenticate the requests
and NAK them regardless of what operation is requested.
Signed-hostap: Jouni Malinen <j@w1.fi>
New configuration parameters radius_auth_req_attr and
radius_acct_req_attr can now be used to add (or override) RADIUS
attributes in Access-Request and Accounting-Request packets.
Signed-hostap: Jouni Malinen <j@w1.fi>
radius_request_cui=1 configuration parameter can now be used to
configure hostapd to request CUI from the RADIUS server by including
Chargeable-User-Identity attribute into Access-Request packets.
Signed-hostap: Jouni Malinen <j@w1.fi>
If Access-Accept packet includes the Chargeable-User-Identity attribute,
copy this attribute as-is into accounting messages.
Signed-hostap: Jouni Malinen <j@w1.fi>
There was a technical change between the last IETF draft version
(draft-arkko-eap-aka-kdf-10) and RFC 5448 in the leading characters
used in the username (i.e., use unique characters for EAP-AKA' instead
of reusing the EAP-AKA ones). This commit updates EAP-AKA' server and
peer implementations to use the leading characters based on the final
RFC.
Note: This will make EAP-AKA' not interoperate between the earlier
draft version and the new version.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Incorrect identity string could end up being used with EAP-AKA' when
the EAP client is using pseudonym. This code was supposed to use
sm->identity just like the EAP-AKA case.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
The misplaced parenthesis caused Device ID matching to check only the
first octet of the P2P Device Address, i.e., we could have replied to
Probe Request frames that was searching for another device if any of
the last five octets of the address were different.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
An existing persistent group information can now be used to force GO
Negotiation to use the previously used SSID/passphrase from a persistent
group if we become a GO. This can be used as an alternative to inviting
a new P2P peer to join the group (i.e., use GO Negotiation with GO
intent 15 instead of starting an autonomous GO and using invitation),
e.g., in case a GO Negotiation Request is received from a peer while we
are not running as a GO. The persistent group to use for parameters is
indicated with persistent=<network id> parameter to p2p_connect.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commits 17bef1e97a and
ffe98dfb88 started using p2p_add_device()
with other frames than just Probe Response frames from scan results.
However, these changes did not take into account that the PD Request
and Invitation Request frames are normally received on the our own
Listen channel, not on the Listen channel of the peer. As such, these
frames must not be used to update Listen channel information for the
peer.
Fix this by letting p2p_add_device() know whether the results are from
scan results and if not, skip the peer table updates that are specific
to Probe Response frames.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Add provisional discovery failure ctrl_iface event
(P2P-PROV-DISC-FAILURE) to indicate to the application layer in case of
PD failure.
Signed-off-by: Deepthi Gowri <deepthi@codeaurora.org>
Commit d9bdba9f86 was supposed to allow
p2p_listen to schedule new after scan operation only if a p2p_connect
operation was not pending. However, it used incorrect P2P_AFTER_SCAN_
value for this and did not actually prevent overriding of p2p_connect
and could have caused some p2p_listen operations to be skipped
unnecessarily.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
Unlike the unicast SD queries, the queries directed to all peers depend
on P2P_DEV_SD_INFO flag being cleared to allow the query to be sent to
a peer that has previously replied to any SD query.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the timeout scheduled during the previous association was
used after reassociation if the STA entry had not yet been removed. The
next timeout does not need to happen that quickly, so reschedule it
during reassociation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to figure out what exactly was done with the
ap_handle_timer registration/cancellation based on a debug log.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The next ap_handle_timer action was already cleared when association
is handled with user space -based SME. However, this step was missing
from the driver callback for indicating new association. This could
result in the first ap_handle_timer timeout on the new association
removing the station unexpectedly. Fix this by resetting the timeout_next
in hostapd_notif_assoc().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
A station may move from EAP/WPS key_mgmt to PSK using re-association. In
practice, this can happen most likely with WPS when the station runs
through the provisioning step (EAP/WPS) followed by PSK authentication.
If a deauthentication event is missed from the station for whatever
reason, the EAPOL authenticator state machine could have been left
running.
This can result in various issues, including unexpected disconnection of
the station while both the 4-way handshake and EAPOL authenticator state
machines (EAP) are running at the same time when the supplicant is
trying to use PSK. Fix this by explicitly clearing EAPOL authenticator
state machine on (re)association if the new association does not use it.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
When starting an AP with HT40 on 2.4 GHz, limit the set of channels
to scan for based on the affected frequency range to speed up the
AP setup.
Signed-hostap: Jouni Malinen <j@w1.fi>
Mark the debug print excessive and print it only in case the entropy
collection is used since this function can get called pretty frequently.
Signed-hostap: Jouni Malinen <j@w1.fi>
OpenSSL wrapper was using the same certificate store for both Phase 1
and Phase 2 TLS exchange in case of EAP-PEAP/TLS, EAP-TTLS/TLS, and
EAP-FAST/TLS. This would be fine if the same CA certificates were used
in both phases, but does not work properly if different CA certificates
are used. Enforce full separation of TLS state between the phases by
using a separate TLS library context in EAP peer implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
This was never really completed and is of not much use at this point,
so clean up the repository by removing the Symbian-specific changes.
Signed-hostap: Jouni Malinen <j@w1.fi>
This optional parameter to the BSS command can be used to select which
fields are included in the output to avoid having to parse through
unneeded information and to reduce the buffer size.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
There is no need to subscribe to event messages during deinit process,
so skip this to avoid unnecessary operations and to keep the debug logs
a bit cleaner.
Signed-hostap: Jouni Malinen <j@w1.fi>
This should keep us from getting into a state where we bounce large
numbers of stations all at once. Spreading out the bounce should cause
less stress on the network as the idle stations won't all be trying to
reconnect at once.
Signed-hostap: Ben Greear <greearb@candelatech.com>
wps_vendor_ext_m1 configuration parameter can now be used to add a
vendor specific attribute into the WPS M1 message, e.g., for
Windows Vertical Pairing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This was previously indicated as disassociation, but the P2P group
session ending case expect a deauthentication notification. Since the
cfg80211 disconnection event does not really indicate which frame was
used, the easiest approach for now seems to be to just indicate these
as deauthentication events.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use reason code 3 (Deauthenticated because sending STA is leaving)
instead of reason code 2 (Previous authentication ot valid) in the
Deauthentication frame sent at the time a BSS is terminated. This is
more accurate reason for the message and allows the stations to get
better understand on why they were disconnected. This can be useful
especially for P2P clients that can use this as a signal that the
P2P group session was ended per P2P specification section 3.2.9.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
On P2P group removal, the GO is deinitialized correctly (and the vif
mode is set back to sta in case of nl80211), but the P2P client mode
wasn't deinitialized, and the nl80211 vif stays in P2P client mode.
Add a new deinit_p2p_cli op (similar to deinit_ap), which currently only
sets the interface back to station mode.
Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
Some applications require knowing about probe requests to identify
devices. This can be the case in AP mode to see the devices before they
connect, or even in P2P mode when operating as a P2P device to identify
non-P2P peers (P2P peers are identified via PeerFound signals).
As there are typically a lot of probe requests, require that an
interested application subscribes to this signal so the bus isn't always
flooded with these notifications. The notifications in DBus are then
unicast only to that application.
A small test script is also included.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.
Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.
My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
When hostapd is about to start an AP using HT40, it starts a scan to
check whether it is allowed or not. If OLBC is detected before the
scan has completed, it sets the beacons prematurely.
To fix this, instead of setting all beacons when OLBC is detected,
only update the ones that have already been started.
Signed-off-by: Luciano Coelho <coelho@ti.com>
ieee802_1x_encapsulate_radius() frees the RADIUS message if
radius_client_send() returns error. This could have resulted in use of
freed memory and double freeing of the RADIUS message if send() fails
since the message is also left in the retransmit list. Avoid this by not
returning error to the caller in such a case.
Signed-off-by: Alexander Couzens <lynxis@c-base.org>
Add the option (-T) to wpa_supplicant to log all debug messages into the
kernel tracing, allowing to aggregate kernel debugging with
wpa_supplicant debugging and recording all with trace-cmd.
Since tracing has relatively low overhead and can be filtered
afterwards, record all messages regardless of log level. However, it
will honor the -K option and not record key material by default.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The "BSS p2p_dev_addr=address" command uses p2p_parse_dev_addr() to
figure out the P2P Device Address of the GO from scan results. This used
to work only if the P2P IE was received from Probe Response frames since
only those include the P2P Device Info attribute. Make this work with
Beacon frames, too, by using P2P Device ID attribute if the P2P Device
Info attribute is not present.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A network block specific background scan period can now be configured
for drivers that implement internal background scan mechanism for
roaming and BSS selection.
Signed-hostap: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Implement wps_cancel for hostapd similarly to how it was already
supported in wpa_supplicant AP mode.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_pref_chan configuration parameter can now be used to set the
list of preferred channel for P2P GO Negotiation. This will be used
in the priority order if the peer does not support the channel we
are trying to use as the GO (configured operating channel or the
best 2.4 GHz/5 GHz channel) for the case where a forced channel is
not used.
p2p_pref_chan=<op class:channel>,...
For example:
p2p_pref_chan=81:1,81:2,81:3,81:4,81:5,81:6
This would configure 2.4 GHz channels 1-6 as the preferred ones with
channel 1 the most preferred option.
These configuration parameters can be set in wpa_supplicant.conf and
dynamically updated with "wpa_cli set <param> <value>".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When drivers advertise their capability to free up inactive
stations based on ap_max_inactivity, send the inactivity period
timeout to driver in NL80211_ATTR_INACTIVITY_TIMEOUT. This
introduces a WPA_DRIVER_FLAGS (WPA_DRIVER_FLAGS_INACTIVITY_TIMER)
so that the inactivity period will be sent only when this capability
bit is set.
Signed-hostap: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
When the driver (or firmware) implements AP mode SME, the use of raw
management frame TX functions is not working properly at the moment. As
an initial step, convert these AP mode operations to use
NL80211_CMD_DEL_STATION and do not claim that driver provides TX status
for deauth/disassoc frames. While this does not address all use cases
(e.g., reason code is not specified in the command), this fixes number
of issues where the station does not get disconnected properly.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 30680e9332 changed the length
of the implicit challenge result to match with the exact length used
in TTLS. However, it failed to update the peer_challenge generation
to use a separate random value. Previously, this was generated as
part of the implicit challenge, but more correct way would have been
to generate a random value for it separately. Do this now to fix the
read after the allocated buffer (16 bytes after the implicit
challenge).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
This DO has a maximum length of 127 bytes (TS 102 221), so better use
large enough buffer when reading the record.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, this provisioning info was cleared using the P2P Interface
Address of the GO as the key. That did not always work in the case the
where we joined an already running group. This could result in the next
connection to that same GO skipping provision discovery. Fix this by
finding the peer entry based on its P2P Device Address instead of the
P2P Interface Address which may not always be set.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
If a wildcard PIN is used on any of the radios that hostapd is
controlling, invalidate the matching PIN on all the other radios
to avoid multiple uses of the same PIN.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Use Device Password ID in WSC IE of Probe Request and Probe Response
frames to advertise immediate availability of WPS credentials per P2P
specification sections 3.1.2.1.1 (Listen State), 3.1.2.1.2 (Scan Phase),
and 3.1.2.1.3 (Find Phase).
For now, the Device Password ID is set only for the case where we are
active GO Negotiation with a specific peer. In practice, this means that
the Probe Response frames during pending GO Negotiation (whenever in
Listen state) indicate availability of the credential.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_flush did not explicit stop all P2P operations, i.e., the exact
behavior depended on the P2P module state at the time the p2p_flush
command was issued. Make this more consistent by explicitly calling
p2p_stop_find() from p2p_flush().
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If Listen state was in progress on another channel when a request to
send an Action frame (e.g., Provision Discovery Request or Invitation
Request to a peer on the peer's Listen channel that is different from
our Listenc hannel) is issued, wpa_supplicant tried to use concurrent
remain-on-channel operations. While some drivers can handle this
cleanly, there are drivers that don't and wpa_supplicant is not expected
to request concurrent remain-on-channel operations.
Fix this by cancelling the ongoing remain-on-channel with stop_listen
prior to sending the Action frame on another channel. If a P2P search
was in progress, it will be continued after the timeout on the new
operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The new venue_name configuration parameter can now be used to configure
the ANQP Venue Name values that stations can request through GAS.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds GAS/ANQP implementation into hostapd. This commit brings in
the basic GAS/ANQP functionality, but only the ANQP Capability List
element is supported.
For testing purposes, hostapd control interface SET command can be used
to set the gas_frag_limit parameter dynamically.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
New global configuration parameters pcsc_reader and pcsc_pin can now be
used to initialize PC/SC reader context at start of wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
Definition of ANonce selection in IEEE Std 802.11i-2004 is somewhat
ambiguous. The Authenticator state machine uses a counter that is
incremented by one for each 4-way handshake. However, the security
analysis of 4-way handshake points out that unpredictable nonces help in
preventing precomputation attacks. Instead of the state machine
definition, use an unpredictable nonce value here to provide stronger
protection against potential precomputation attacks.
Signed-hostap: Jouni Malinen <j@w1.fi>
Move disassociate and deauthenticate commands to ctrl_iface_ap.c, so
that they ares accessible for wpa_supplicant AP mode and wpa_cli (with
CONFIG_AP option enabled).
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Remove unnecessary second copy of the URL and too long memory
allocation. In addition, avoid use of strcpy() to keep static analyzers
happier.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like a RTM_NEWLINK event claiming the interface to be UP is
delivered just before removing an interface after having first indicated
that the interface was going down/removed. Ignore this event if the
interface is not present anymore at the moment the event is processed.
This fixes issues where an interface that was re-added after being
removed did not get reconfigured properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
It looks like a RTM_NEWLINK event claiming the interface to be UP is
delivered just before removing an interface after having first indicated
that the interface was going down/removed. Ignore this event if the
interface is not present anymore at the moment the event is processed.
This fixes issues where an interface that was re-added after being
removed did not get reconfigured properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
AT_NEXT_PSEUDONYM is supposed to be included only in the Challenge
messages, not in the Re-authentication messages. This attribute was
incorrectly included in the Re-authentication messages and could have
been used to update the pseudonym state on the server without the peer
updating its state.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
Add support to send Action frames to the driver.
Add support for TSPEC req and adding STA node to the driver.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"wpa_cli set radio_disabled 1/0" can be used to disable/enable
radio to simulate out-of-radio-range condition in a testbed
device.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit d9a38716cc did this for
hostapd_eapol_tx_status() but missed the older hostapd_tx_status()
path. Address that case, too.
The TX status event may be received after a station has been
disassociated in cases where the disassociation is following a
transmission of a Data frame. Ignore such events if the STA is not
associated at the moment the event is being processed. This avoids
confusing debug entries and rescheduling of the EAPOL TX timeouts for
STAs that are still in the STA table, but are not really in active EAPOL
session.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
The SetSelectedRegistrar timeout was registered for each registrar
instance, but the only context pointer (struct subscription *) was
shared with each registrar which resulted in the timeout getting
cancelled for some of the registrar instances before the selected
registrar (ER) information was cleared.
In addition, when an ER unsubscribed from receiving events, the
selected registrar information got cleared only from a single
registrar.
Fix these issues by registering a pointer to the registrar
instance in the timeout and by iterating over all UPnP interfaces
when removing a subscription.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
eloop_sock_table_add_sock() needs to fail if pollfd array allocation
fails instead of returning success and leaving behind no buffer.
Signed-hostap: Jouni Malinen <j@w1.fi>
In IBSS RSN cfg80211/mac80211 now waits for userspace to authorize new
stations. This patch makes wpa_supplicant notify the driver when a
station can be considered authorized.
Signed-hostap: Antonio Quartulli <ordex@autistici.org>
When using more than around 200 virtual stations, we start hitting the
max number of file descriptors supported by select(). This patch adds
support for poll(), which has no hard upper limit.
Signed-hostap: Ben Greear <greearb@candelatech.com>
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.
Signed-hostap: Jouni Malinen <j@w1.fi>
Remove the GPL notification text from EAP-pwd implementation per
approval from Dan Harkins who contributed these files.
(email from Dan Harkins <dharkins@lounge.org> dated
Wed, 4 Jan 2012 16:25:48 -0800)
Signed-hostap: Jouni Malinen <j@w1.fi>
In case of !defined(IEEE8021X_EAPOL) the definition of the stub
pmksa_cache_get() in rsn_supp/pmksa_cache.h is not correct. This patch
adds the missing argument to the function definition to fix a
regression from commit 96efeeb66b.
Signed-hostap: Antonio Quartulli <ordex@autistici.org>
Search (p2p_scan) could already have been started at the point
remain-on-channel end event is being processed, e.g., if an Action frame
TX is reported immediately aftet the end of an earlier remain-on-channel
operation and the response frame is sent using an offchannel operation
while p2p_find is still in progress. Avoid trying to re-run p2p_scan
while the previous one is still running.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 39185dfa54 changed the p2p_scan()
callback to return 1 in some cases, but forgot to change this p2p_scan()
call to handle that properly. Fix this by processing any non-zero value
as an error. This regression could leave the P2P module in state where
it believed a P2P scan was still running and refused to start some
operations until that scan gets completed (which would never happen
since it was not really started).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, PINs that are added with a wildcard UUID were allowed to
be used only by a single Enrollee. However, there may be more than one
Enrollee trying to connect when an AP indicates that active Registrar
is present. As a minimal workaround, allow two Enrollees to try to use
the wildcard PIN. More complete extension could use timeout and allow
larger set of Enrollees to try to connect (while still keeping in mind
PIN disabling requirement after 10 failed attempts).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"BSS p2p_dev_addr=<P2P Device Address>" can now be used to fetch a
specific BSS entry based on the P2P Device Address of the GO to avoid
having to iterate through the full BSS table when an external program
needs to figure out whether a specific peer is currently operating as
a GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When the GO negotiation peer is assigned, the state also cannot be IDLE,
SEARCH, or LISTEN_ONLY.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When looking for PMKSA cache entries to use with a new association, only
accept entries created with the same network block that was used to
create the cache entry.
Signed-hostap: Jouni Malinen <j@w1.fi>
This fixes a corner case where a STA that has PMKSA cache entry (or
valid FT keys) could try to use full EAPOL/EAP authentication and fail.
If the STA will then try to use the still valid PMKSA cache entry (or
FT) before the STA entry has been cleared, authFail could have been left
to TRUE. That will make EAPOL authenticator PAE state machine enter HELD
state even though authSuccess was already forced to TRUE. This results
in the STA getting disconnected even though it should be allowed to
continue with 4-way handshake. While this is unlikely to happen in
practice, it is better to get this fixed by clearing authFail when
setting authSuccess.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
The TX status event may be received after a stations has been
disassociated in cases where the disassociation is following a
transmission of a Data frame. Ignore such events if the STA is not
associated at the moment the event is being processed. This avoids
confusing debug entries and rescheduling of the EAPOL TX timeouts for
STAs that are still in the STA table, but are not really in active EAPOL
session.
Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
While the exponential increase in the lockout period provides an
efficient mitigation mechanism against brute force attacks, this
additional trigger to enter indefinite lockout period (cleared by
restarting hostapd) will limit attacks even further by giving maximum of
10 attempts (without authorized user action) even in a very long term
attack.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This allows HT capabilities overrides on kernels that
support these features.
MCS Rates can be disabled to force to slower speeds when using HT.
Rates cannot be forced higher.
HT can be disabled, forcing an 802.11a/b/g/n station to act like
an 802.11a/b/g station.
HT40 can be disabled.
MAX A-MSDU can be disabled.
A-MPDU Factor and A-MPDU Density can be modified.
Please note that these are suggestions to the kernel. Only mac80211
drivers will work at all. The A-MPDU Factor can only be decreased and
the A-MPDU Density can only be increased currently.
Signed-hostap: Ben Greear <greearb@candelatech.com>
When there is not enough entropy and there are two station associating
at the same time, one of the stations will be rejected, but during
that rejection, the "reject_4way_hs_for_entropy" flag gets cleared. This
may allow the second station to avoid rejection and complete a 4-Way
Handshake with a GTK that will be cleared as soon as more entropy is
available and another station connects.
This reworks the logic to ban all 4-way handshakes until enough entropy
is available.
Signed-hostap: Nicolas Cavallari <cavallar@lri.fr>
In multiple BSSes scenario for the drivers that do not use
monitor interface and do not implement AP SME, RX MGMT
frame subscription happens only for the default bss (first_bss).
Subscribe for RX MGMT frames for such BSSes.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Commit e4fb216769 moved frequency
storage from driver struct to bss struct and is assigned in
wpa_driver_nl80211_set_freq. As this wpa_driver_nl80211_set_freq is
triggered only on the first_bss, bss->freq for other BSSes is never
being set to the correct value. This sends MLME frames on frequency zero
(initialized value of freq) for BSSes other than the first.
To fix this derive frequency value from first_bss.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
This patch allows to log hexdumps into syslog.
This is useful when testing, as syslog's network logging
helps to collect debug outputs from several machines.
Signed-hostapd: Nicolas Cavallari <cavallar@lri.fr>
The pseudonym identity should use a realm in environments where a realm is
used. Thus, the realm of the permanent identity is added to the pseudonym
username sent by the server.
Signed-hostap: Simon Baatz <gmbnomis@gmail.com>
The pseudonym identity should use a realm in environments where a realm is
used. Thus, the realm of the permanent identity is added to the pseudonym
username sent by the server.
Signed-hostap: Simon Baatz <gmbnomis@gmail.com>
When the "bssid=" option is set for an IBSS network and ap_scan = 2,
ask the driver to fix this BSSID, if possible.
Previously, any "bssid=" option were ignored in IBSS mode when ap_scan=2.
Signed-hostap: Nicolas Cavallari <cavallar@lri.fr>
It looks like Windows 7 WPS implementation does not like multiple
Authentication/Encryption Type bits to be set in M7 AP Settings
attributes, i.e., it refused to add a network profile if the AP
was configured for WPA/WPA2 mixed mode and AP PIN was used to
enroll the network.
Leave only a single bit set in the Authentication/Encryption Type
attributes in M7 when the AP is acting as an Enrollee to avoid this
issue.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
A P2P Action frame may need to be sent on another channel than the GO's
operating channel. This information was lost in
wpa_driver_nl80211_send_action() in the case the interface was in AP
mode. Pass the frequence and related parameters to send_mlme mechanism
to allow the correct frequence to be used with the send frame command in
AP (P2P GO) mode.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Number of places in hostapd use ap_sta_disconnect() instead of
ap_sta_disassociate() or ap_sta_deauthenticate(). There are some
differences between these functions, e.g., in the area how quickly
the EAPOL state machines get deinitialized. This can result in
somewhat unexpected events since the EAPOL/WPA authenticator
state machines could remain running after deauthentication.
Address this by forcing EAPOL/WPA authenticator state machines
to disabled state whenever ap_sta_disconnect() is called instead
of waiting for the deauthentication callback or other timeout
to clear the STA.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Even though we may not update P2P peer entry while connected to the
peer as a P2P client, we should not be expiring a P2P peer entry while
that peer is the GO in a group where we are connected as a P2P client.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Even though we may not receive a Probe Response from the peer during
the connection, we should not be expiring a P2P peer entry while that
peer is connected to a group where we are the GO.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The cookie value needs to be fetched in GO mode, too, to be able to
indicate TX status callbacks with drivers that handle AP mode SME
functionality internally. This fixes issues with client discoverability
where TX status callback for GO Discoverability Request is needed to
trigger the GO to send Device Discoverability Response.
Some SIM cards do not include MNC length with in EF_AD. Try to figure
out the MNC length based on the MCC/MNC values in the beginning of the
IMSI. This covers a prepaid Elisa/Kolumbus card that would have ended
up using incorrect MNC length based on the 3-digit default.
Signed-hostap: Jouni Malinen <j@w1.fi>
The temporary IMSI buffer can be used for this without needing the
extra memory allocation. In addition, the implementation is easier
to understand when the extra identity prefix value for EAP-SIM/AKA
is not included while fetching MCC/MNC from the IMSI.
Signed-hostap: Jouni Malinen <j@w1.fi>
The EF-AD (administrative data) file may contain information about the
length of the MNC (2 or 3 digits) in the IMSI. This can be used to
construct the realm according to 3GPP TS 23.003 during EAP-SIM or
EAP-AKA authentication.
Signed-hostap: Simon Baatz <gmbnomis@gmail.com>
This patch notifies the upper framework that an on-going discovery has
been stopped. This is useful in cases where a p2p_find with a timeout
value initiated by the upper framework has been finished or when the
framework initiated "p2p_find" is stopped by a "p2p_connect".
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Some deployed station implementations seem to send msg 4/4 with
incorrect type value in WPA2 mode. Add a workaround to ignore that issue
so that such stations can interoperate with hostapd authenticator. The
validation checks were added in commit
f8e96eb6fd.
Signed-hostap: Jouni Malinen <j@w1.fi>
The Device ID attribute was already used in Listen state, but it was
ignored in GO role. Verify that there is a match with Device ID in
GO rule, too, before replying to the Probe Request frame.
Signed-hostap: Jouni Malinen <j@w1.fi>
dev_id=<P2P Device Addr> can now be specified as an argument to
p2p_find to request P2P find for a specific P2P device.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some supplicant implementations (e.g., Windows XP WZC) update SNonce for
each EAPOL-Key 2/4. This breaks the workaround on accepting any of the
pending requests, so allow the SNonce to be updated even if we have
already sent out EAPOL-Key 3/4.
While the issue was made less likely to occur when the retransmit
timeout for the initial EAPOL-Key msg 1/4 was increased to 1000 ms,
this fixes the problem even if that timeout is not long enough.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Now that we can use driver_nl80211.c with non-mac80211 drivers that
implement SME/MLME internally, we may not get inactivity time from the
driver. If that is the case, we need to skip disconnection based on
maximum inactivity timeout. This fixes some unexpected disconnection
cases with ath6kl in AP mode.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The deauthentication and disassociation events from nl80211 were being
processed identically regardless of whether the frame was generated by
the local STA or the AP. This resulted in fast reconnection mechanism
getting triggered even in the case where the disconnection was detected
locally (e.g., due to beacon loss) while this was supposed to happen
only in the case where the AP is sending an explicit Deauthentication
or Disassociation frame with a specific reason code.
Fix this by adding a new deauth/disassoc event variable to indicate
whether the event was generated locally.
Signed-hostap: Jouni Malinen <j@w1.fi>
IEEE Std 802.1X-2004 does not clear authWhile and heldWhile in this
case, but doing so allows the timer tick to be stopped more quickly when
the port is not enabled. Since these variables are used only within HELD
and RECEIVE states, clearing them on initialization does not change
actual state machine behavior. This reduces some unnecessary operations
in port disabled state and cleans up the wpa_supplicant debug log after
disconnection.
Signed-hostap: Jouni Malinen <j@w1.fi>
Since wps_registrar_pbc_timeout is called to stop PBC, previously
registered wps_registrar_pbc_timeout must be canceled when canceling
the WPS operation.
Signed-off-by: Spencer Chang <jungwalk@gmail.com>
The offchanok parameter is hardcoded to one in number of paths and that
added NL80211_ATTR_OFFCHANNEL_TX_OK attribute to NL80211_CMD_FRAME
unconditional. cfg80211 rejects this with EINVAL if the driver does not
indicate support for offchannel TX. Fix this by not requesting
offchannel TX depending on driver capabilities. Remain-on-channel
operation was used for those cases anyway, so the additional attribute
was not really needed for these in the first place.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When nl80211_setup_ap() has enabled Probe Request reporting, this must
not be disabled when P2P Listen state is stopped to avoid breaking AP
mode operations. This could happen, e.g., if a Probe Request frame was
received from a P2P device that the we are trying to invite to our group
(i.e., when operating in GO role). p2p_probe_req_rx() calls
p2p_invite_start() in this case and that ends up calling
p2p->cfg->stop_listen() which calls probe_req_report() driver op.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd uses the poll method to check if the station is alive
after the station has been inactive for ap_max_inactivity seconds.
Make the poll mechanism configurable so that user can choose to
disconnect idle clients.
This can be especially useful when some devices/firmwares have
restrictions on the number of clients that can connect to the AP
and that limit is smaller than the total number of stations trying
to use the AP.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
The 100 ms timeout on retransmitting group key message can be too short
for stations that are in power save mode or if there is a large number
of association stations. While the retransmission of the EAPOL-Key frame
should allow this to be recovered from, it is useful to avoid
unnecessary frames to save soem CPU and power.
Signed-hostap: Jouni Malinen <j@w1.fi>
Drivers that use device SME in AP mode may still need to be
subscribed for Action frame RX when monitor interface is not used.
This fixes number of P2P GO operations with ath6kl.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Poll command may be enough for mac80211 to figure out whether monitor
interface is to be used, but this change did not take into account
non-mac80211 drivers that support AP mode without monitor interface.
For example, ath6kl needs to get use_monitor disabled.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new persistent group network block field, p2p_client_list, to
maintain a list of P2P Clients that have connected to a persistent
group. This allows GO of a persistent group to figure out more easily
whether re-invocation of a persistent group can be used with a specific
peer device.
Signed-hostap: Jouni Malinen <j@w1.fi>
The P2P module provides access to public peer data in struct
p2p_peer_info. Use this to build the P2P_PEER information in
ctrl_iface.c instead of providing such text format data from the P2P
module.
The internal data that was previously built in p2p_get_peer_info() as
part of the text format peer data is now available through a separate
p2p_get_peer_info_txt() function. This is still included in P2P_PEER
output to maintain backwards compatibility with external programs that
could have started to use this. However, it should be noted that this
data is not really supposed to be used for anything else apart from
debugging purposes and its format is subject to change.
Signed-hostap: Jouni Malinen <j@w1.fi>
p2p_get_peer_info() was used in multiple places just to check whether a
specific peer is known. This was not the designed use for the function,
so introduce a simpler function for that purpose to make it obvious that
the p2p_get_peer_info() function is actually used only in ctrl_iface.c.
Signed-hostap: Jouni Malinen <j@w1.fi>
If p2p_listen is issued during a p2p_scan, a pending after-scan operation
is scheduled. However, since there is support for only a single pending
operation, this was able to override a previously scheduled pending
connect command. This can break some command sequences, so give higher
priority to pending connect operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Android ICS system/core/libnl_2 has very limited genl_ctrl_resolve()
implementation that cannot handle names other than nlctrl. Work
around that by implementing more complete genl_ctrl_resolve()
functionality within driver_nl80211.c for Android builds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This event can be very frequent in AP mode when Beacon frames from
neighboring BSSes are delivered to user space. Drop the debug
message priority from DEBUG to EXCESSIVE for Beacon frames.
Signed-hostap: Jouni Malinen <j@w1.fi>
I needed this patch to compile against the latest
libnl code. I added this to my config file:
CONFIG_LIBNL32=y
Signed-hostap: Ben Greear <greearb@candelatech.com>
When waiting for go_neg frame from the peer in WAIT_PEER_CONNECT state,
I have observed that sometimes it takes 20 to 30 secs for successful GO
negotiation. I also found out that it is because of 1 second idle time,
in WAIT_PEER_CONNECT state. While it is good to have 1 second idle time
[for doing power-save or doing some other legacy STA Scan or some other
useful stuff], this makes GO Negotiation process slow.
We wait for 1 second idle and then listen for a random time between
100(min)-300(max) ms. Assume P1 is in WAIT_PEER_CONNECT state and P2 is
the one which is now to send go_neg frame. If P2 sends GO Negotiation
frame just at the boundary of 300 ms of P1 and assume that P2 takes
close to 600-800 ms for one iteration of sending go_neg request (one
iteration is GO Negotiation Request frame time + dwell time +
listen_time), P2 needs to transmit at least 16-18 Action frames for
hitting the listen time of P1.
Following patch reduces the idle time to 500 ms. Alternatively we can
increase the listen time interval to 500 ms just for WAIT_PEER_CONNECT
state.
Provision discovery from a known peer should actually check for
dev->flags & P2P_DEV_PROBE_REQ_ONLY. This is creating an issue of
updating the listen frequency of peer with the PD request frame
frequency. PD request frame will be sent by the peer on our local listen
frequency. This patch fixes that error. Suggested check has already been
implemented in the invitation req receive path.
The Provision Discovery Request needs to be sent on the operating
channel of the GO and as such, the frequency from the BSS table
(scan results) need to override the frequency in the P2P peer
table that could be based on the Listen channel of the GO.
Signed-hostap: Jouni Malinen <j@w1.fi>
The GO negotiation response is very cryptic at the moment. For a success
message we only know on which interface the negotiation succeeded, not
which peer. For a failure we know the interface also and a status code
(number).
It will be very useful for clients to know upon receipt of such a message
which peer the negotiation occurred with.
Now that the peer information is available and the API is changed
already, the function composing the D-Bus message might as well include
all GO negotiation information. This is done with a dict to make things
easier on clients if this result information changes down the line.
Signed-hostap: Reinette Chatre <reinette.chatre@intel.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
When the station is connected to P2P GO after calling p2p_find command
the device sees itself. It is related to lack of filtering itself from
clients connected to P2P GO.
Step by step:
1. dev1: p2p_group_add
2. dev2: p2p_connect <MAC1> pbc join
3. dev1: wps_pbc
4. dev2: p2p_find
Skip P2P client information for our own device from a GO with which
we are connected.
It looks like some USIM cards respond with 0x67 (Wrong length) instead
of 0x6c to 00 b2 01 04 ff. This was getting rejected in
scard_get_record_len(). ETSI TS 102 221 is not very clear on this
detail, but it looks fine to accept the 0x67 error value, too, to learn
the record length.
Signed-hostap: Jouni Malinen <j@w1.fi>
Return 1/0 instead 0/-1 to indicate valid/invalid element so that
the if statement makes more sense with !wmm_valid().
Signed-hostap: Jouni Malinen <j@w1.fi>
This updates a previous patch did more or less the same thing by
providing the qosinfo as a single variable to the driver wrappers.
Signed-hostap: Jason Young <jason.young@dspg.com>
Add uapsd_queues and max_sp fields to sta_info struct,
and pass them to the sta_add callback.
These values are determined by the WMM IE in the (Re)Association Request.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Check whether the driver advertises support for U-APSD
in AP mode, and evaluate wmm_uapsd only in this case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
The wpa_hexdump_ascii() call did not get converted properly and this
was missed becaused of it getting defined out from the build. Anyway,
this better use the correct variable names should that debug print
ever be enabled for Android.
Signed-hostap: Jouni Malinen <j@w1.fi>
A Pending Provision Discovery Request was sent in SEARCH phase after a
previous provision discovery timeout. Fix this by resetting the config
method of P2P device in the pending PD reset function. This avoids the
sending of a pending Provision Discovery Request during the next P2P
search.
Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Some debug messages used incorrect name for Provision Discovery.
Replace "Provisioning Discovery" with "Provision Discovery".
Signed-hostap: Jouni Malinen <j@w1.fi>
It is safer to assume that the driver could be using NoA and reject
any Presence Request unless we are sure that noa NoA is in use.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows per-device PSK to be configured for WPA-Personal using a
RADIUS authentication server. This uses RADIUS-based MAC address ACL
(macaddr_acl=2), i.e., Access-Request uses the MAC address of the
station as the User-Name and User-Password. The WPA passphrase is
returned in Tunnel-Password attribute in Access-Accept. This
functionality can be enabled with the new hostapd.conf parameter,
wpa_psk_radius.
Signed-hostap: Michael Braun <michael-dev@fami-braun.de>
WPS overlap detection can detect false overlap if a P2P peer
changes UUID while authentication is ongoing. Changing UUID
is of course wrong but this is what some popular devices do
so we need to work around it in order to keep compatibility
with these devices. There already is a mechanism in WPS
registrar to skip overlap detection if P2P addresses of two
sessions match but it wasn't really triggered because the
address wasn't filled in in the caller function.
Let's fill in this address and also clean up WPS PBC sessions
on WSC process completion if UUID was changed.
Signed-hostap: Vitaly Wool<vitalywool@gmail.com>
Pass the raw Probe Response template to kernel via netlink using the
set_ap() driver callback. The data is sent as one of the Beacon
attributes.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Configure a Probe Response template for drivers that support it. The
template is updated when the Beacon template is updated.
The Probe Response template is propagated to the driver via the set_ap()
callback.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
This is needed for Probe Response template, so move the code into a
separate function that can be shared.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Translate nl80211 flags to wpa_supplicant flags for Probe Response
offload support. The existence of the nl80211 PROBE_RESP_OFFLOAD_SUPPORT
attribute means Probe Response offload is supported. The value of the
attribute is a bitmap of supported protocols.
Signed-hostap: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
This previously helped when debugging some auth issues when hitting the
AP with 128 association attempts all at once.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Append "p2p_dev_addr" parameter to AP-STA-DISCONNECTED event for P2P
connections. In addition, for AP-STA-CONNECTED event during P2P
connection, the "dev_addr=" print is replaced with "p2p_dev_addr=" to
be more consistent with other events.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Storing the address in the BSS instead of the DRV struct makes it usable
for hostapd and thus gets rid of the linux_get_ifhwaddr() call when
receiving a spurious frame.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Testing code can now be enabled in the hostapd RADIUS server to dump
each derived MSK into a text file (e.g., to be used as an input to
wlantest). This functionality is not included in the default build
and can be enabled by adding the following line to hostapd/.config:
CFLAGS += -DCONFIG_RADIUS_TEST
The MSK dump file is specified with dump_msk_file parameter in
hostapd.conf (path to the dump file). If this variable is not set,
MSK dump mechanism is not enabled at run time.
Signed-hostap: Jouni Malinen <j@w1.fi>
If Provision Discovery Request is sent for GO role (i.e., P2P Group ID
attribute is included), add the group interface name to the control
interface event on the GO. This makes it easier to figure out which
ctrl_iface needs to be used for wps_pbc/wps_pin command to authorize
the joining P2P client.
Signed-hostap: Jouni Malinen <j@w1.fi>
If p2p_prov_disc join command is used prior to p2p_connect join,
skip the duplicated provision discovery exchange.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
This can be used to request Provision Discovery Request to be sent
for the purpose of joining a running group, e.g., to request the GO
to display a PIN that we can then use with p2p_connect join command.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Since the nl_cache is not used anymore, there is no need for maintaining
the struct nl80211_handles wrapper for struct nl_handle. Clean this up
by using nl_handle directly.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a rewrite of Ben Greear's patch, making the
nl80211 code use just a single multicast event socket.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
When running AP mode, we need to receive beacons over overlapping BSSes
to handle protection. Use the new nl80211 command for this. As the
command works per wiphy (and we don't want to receive the Beacon frames
multiple times) add an abstraction that keeps track of per-wiphy data.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
These events are necessary to send deauth frames to
stations sending spurious data frames. Subscribe to
them on the per-BSS event socket.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
To achieve this, multiple things are needed:
1) since hostapd needs to handle *all* action frames,
make the normal registration only when in a non-AP
mode, to be able to do this use the new socket
2) store the frequency in each BSS to be able to give
the right frequency to nl80211's mgmt-tx operation
3) make TX status processing reject non-matched cookie
only in non-AP mode
The whole thing depends on having station-poll support
in the kernel. That's currently a good indicator since
the kernel patches are added together.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Fix start of reauthentication after failed authentication with
passthrough (external AAA server) to use internal EAP Identity method.
Signed-hostap: Jouni Malinen <j@w1.fi>
This reverts commit 204dd3f420.
start_reauth was not supposed to be used in this way and setting it
to TRUE in INITIALIZE breaks internal EAP server.
Signed-hostap: Jouni Malinen <j@w1.fi>
When using authentication retry within driver_nl80211.c, a failure on the
second attempt has to be indicated with a driver event since the return
code from wpa_driver_nl80211_authenticate() is not actually delivered to
the core code in that case.
Signed-hostap: Jouni Malinen <j@w1.fi>
cfg80211 rejects NL80211_CMD_AUTHENTICATE with ENOENT if the BSS entry
for the target BSS is not available. This can happen if the cfg80211
entry has expired before wpa_supplicant entry (e.g., during a suspend).
To recover from this quickly, run a single channel scan to get the
cfg80211 entry back and then retry authentication command again. This
is handled within driver_nl80211.c to keep the core wpa_supplicant
implementation cleaner.
Signed-hostap: Jouni Malinen <j@w1.fi>
The pseudonym is a temporary identity, but is no one-time identifier (like
the fast re-authentication identity). Thus, do not forget it if the server
does not include it in every challenge. There are servers that include the
pseudonym identity only at full-auth. [Bug 424]
Make sure sign extension does not end up getting used here by
explicitly type casting the variables to correct size.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 34445d12ee forgot to convert
the hostapd_prepare_rates() inline wrapper for builds that do not
define NEED_AP_MLME.
Signed-hostap: Jouni Malinen <j@w1.fi>
P2P invitation responses are transmitted with the BSSID set to the peer
address. Pass these action frames up to allow the GO to receive the
Invitation Response (and avoid sending the Invitation Request multiple
times).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Set the NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT flag for nl80211 to tell
drivers (mac80211) to not encrypt the EAPOL frames for WEP IEEE 802.1X.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
In preparation for things that receive on a BSS-specific handle,
allocate a CB for it and hook it up to receive functions.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The next patch will add process_bss_event, rename process_event to
process_drv_event to differentiate between them.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
By passing the nl_cb as the context to the eloop function we can
(in the next patch) use the same eloop function for BSS events.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Storing the frequency in the bss struct allows using it for frame
commands in AP mode and not relying on the driver struct as much, which
is good for hostapd mode.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This will allow getting TX status for EAPOL frames
sent as data frames if the driver supports it.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Previously, sm->start_reauth was set to TRUE in SUCCESS2 state to force
reauthentication to start with EAP identity request. This works fine for
the case of EAP success through the AAA passthrough authentication, but
is not enough to handle passthrough authentication failure. sm->identity
is set in that case and getDecision would return PASSTHROUGH instead of
CONTINUE (to Identity method).
Signed-hostap: Jouni Malinen <j@w1.fi>
The RTM_NEWLINK even can have IFF_UP flag even if the interface is
down. Do not generate EVENT_INTERFACE_ENABLED event based on such a
message.
Signed-hostap: Jouni Malinen <j@w1.fi>
A new hostapd.conf parameter, wps_rf_bands, can now be used to fix the
RF Bands value in cases where hw_mode is not set or when operating a
dual band dual concurrent AP.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When hostapd controls multiple radios, WPS operations are started on
all interfaces. However, when the provisioning run had been completed
successfully, actiove WPS mode was stopped only a single interface. Fix
this to iterate through all interfaces so that this is handled
consistently with the starting of WPS operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 628d54639a introduced number
of new WPS related ctrl_iface messages to hostapd. Some of these
were for ER events which do not make any sense to hostapd that
cannot operate as an ER. The WPS_EV_ER_SET_SELECTED_REGISTRAR one
from wps_registrar_sel_registrar_changed_event() was especially
problematic since it can cause wpa_supplicant ER code segfault due
to missing event data.
Revert all the ER specific changes from commit
628d54639a to get rid of the segfault
and undesired extra code in hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This is based on the Android driver_cmd changes that are converted to
use the sched_scan/stop_sched_scan driver_ops for the case where the
driver does not support the new nl80211 commands.
Change-Id: Iaedc340f84650af422bd2ea57d2a8b0a9d4a5330
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
(jm: This is based on the Android change that used driver_cmd. The same
implementation is used for the actual driver interface, but the commands
are now accessed through sched_scan/stop_sched_scan driver_ops instead
of driver_cmd)
While the copy is not used as a null terminated string, this can prevent
some static analyzers from complaining about non-issue.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add support for generating and verifying RFC 3447 RSASSA-PKCS1-v1_5
style DigestInfo for TLS v1.2 CertificateVerify. For now, this is
hardcoded to only support SHA256-based digest.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows the internal TLS implementation to be built for TLS v1.2
support. In addition to the build option, this changes the TLS PRF
based on the negotiated version number. Though, this commit does not
yet complete support for TLS v1.2.
Signed-hostap: Jouni Malinen <j@w1.fi>
Prepare for multiple TLS PRF functions by renaming the SHA1+MD5 based
TLS PRF function to more specific name and add tls_prf() within the
internal TLS implementation as a wrapper for this for now.
Signed-hostap: Jouni Malinen <j@w1.fi>
IW_ENCODE_ALG_PMK and IW_ENC_CAPA_4WAY_HANDSHAKE are not defined in the
Android tree, so add compatibility defines for these.
Signed-hostap: Jouni Malinen <j@w1.fi>
Send the connection events from P2P group to both the group interface
and parent interface ctrl_ifaces to make it easier for external monitor
programs to see these events without having to listen to all group
interfaces when virtual group interfaces are used.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
cfg80211 will reject the NL80211_CMD_START_SCHED_SCAN if too many
match sets are requested. To avoid being completely unable to start
any scheduled scans, skip setting these filters if the driver did
not advertise support for large enough number of match sets.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This adds initial implementation of set_p2p_powersave to allow legacy PS
mode to be configured. P2P PS parameters are not yet supported.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up the source code and makes it less likely that new AKM
addition misses some needed changes in the future.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the station is indicating use of WPS, WSC IE should be added into the
(Re)Association Response frame. This is clear for the case when WSC IE
was included in the (Re)Association Request frame. However, even the
WLAN_STA_MAYBE_WPS case may actually indicate use of WPS. Assume that to
be the case when WPA/WPA2 is enabled (i.e., when the STA does not
include WPA/RSN/WSC IE while AP has WPA/RSN enabled).
Signed-hostap: Jouni Malinen <j@w1.fi>
This makes it clearer that the PMKSA caching entry gets removed from
the driver regardless of how the internal entry from wpa_supplicant
gets cleared. In practice, this call was skipped only for the case
when the entry for the current AP was being updated, so the previous
version was likely to work with all drivers. Anyway, it is cleaner
to explicitly remove the old entry even in that case before the new
entry gets added.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 940a0ce970 moved the STA associated
check from driver_*.c into ieee802_1x_receive(), but failed to take into
account that wired networks and driver_wired.c do not mark the STA entry
associated. Fix this by skipping the check if the driver wrapper is
using a wired network.
Signed-hostap: Jouni Malinen <j@w1.fi>
It's not really valid to send off-channel in all cases,
so pass whether it should be allowed or not and don't
set it in the AP case.
Also, to get the right ifindex for hostapd, pass a bss
pointer instead of the drv pointer.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Some client implementations only wait a few ms after sending a probe
request while scanning. Since probe responses are always sent at a low
rate this can eat quite some airtime and it might be impossible to get
the frame out before the client leaves the channel again. If the client
leaves before all probe reponses where acked this can cause the probe
reponse to be retried quite often consuming even more airtime.
Hence, add a new noack flag to the driver's send_mlme callback that
allows hostapd to request whether the driver should expect an ACK for
this frame or not.
Use the new noack-policy only for broadcast probe requests that contain
a wildcard SSID.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
In some situations it might be benefical to send a unicast frame without
the need for getting it ACKed (probe responses for example). In order to
achieve this add a new noack parameter to the drivers send_mlme callback
that can be used to advise the driver to not wait for an ACK for this
frame.
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
This structure was not really used for anything apart from figuring out
length of the EAP-pwd header (and even that in a way that would not work
with fragmentation). Since the bitfields in the structure could have
been problematic depending on target endianness, remove this unnecessary
structure.
Signed-hostap: Jouni Malinen <j@w1.fi>
Another niceness of OpenSSL is that if the high-order bit of a 521-bit
big num is not set then BN_bn2bin() will just return 65 bytes instead of
66 bytes with the 1st (big endian, after all) being all zero. When this
happens the wrong number of octets are mixed into function H(). So
there's a whole bunch of "offset" computations and BN_bn2bin() dumps the
big number into a buffer + offset. That should be obvious in the patch
too.
The previous EAP-pwd KDF implemented has an issue with group 21, that is
an elliptic curve group based on a 521 bit prime. 521 is not an even
multiple of 8, and therein lies the problem.
OpenSSL's BN library interprets a string of bits as in big-endian format
so all the calls of BN_bin2bn() will take the binary blob of bits and
turn it into a big number in big-endian format. In the EAP-pwd KDF, I am
stretching the key to "primebitlen". When that is not an even multiple
of 8 I have to mask off the excess. But I was masking off the excess
bits in the 1st octet (big endian after all) but that isn't right. The
KDF produces a string of endian-less bits. The 521st bit is the first
bit in the last octet, not the 7th bit in the first octet. So that has
been fixed and you can see in the attached diff what I'm doing.
If the kernel supports this, don't use manual null
data frame transmissions. This is one thing to get
rid of cooked monitor interfaces.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The non-monitor TX currently uses a normal L2 abstraction
socket, but that will also receive frames we don't want,
so use a plain socket that isn't bound for RX. This might
be possible using the L2 abstraction, but we need a plain
socket later for getting TX status events here.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This changes the auto-detection of whether or not the device contains
the AP SME away from monitor interface addition failing to the explicit
attribute in nl80211. Keep the old auto-detection for a little while so
that ath6kl isn't broken right away.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The new event can be used when EAPOL TX status can't be reported as a
complete 802.11 frame but is instead reported as just the EAPOL data as
originally passed to hapd_send_eapol().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Currently OpenSSL implementation of TLS in hostapd loads only top
certificate in server certificate file. Change this to try to the
whole chain first and only if that fails, revert to old behavior.
Signed-off-by: Maciej Szmigiero <mhej@o2.pl>
This patch implements shared_freq handler for driver_nl80211.c. If a
"p2p_group_add" happens after legacy STA association, then this patch
will help to start the GO on the same frequency. This is useful when
supplicant is started on multiple interface running over a singly "PHY"
and the station interface is not used for the P2P device operations.
For example, wpa_supplicant -iwlan0 .. -N -iwlan1 ... and wlan0 is used
for station connection and wlan1 as the P2P device interface.
Signed-hostap: Jithu Jance <jithu@broadcom.com>
Without this, it is impossible to tell exactly which
MLME code returned the error.
Also, convert to wpa_dbg so that we get device names
in the messages.
Signed-hostap: Ben Greear <greearb@candelatech.com>
When GO negotation fails the WPS method is currently not cleared, which
can result in GO negotiation being resumed when a GO negotiation request
frame is received from the peer. That is unexpected as locally we
already gave up.
This manifests itself in getting
1319574733.955685: wlan0: P2P-GO-NEG-FAILURE status=-1
1319574733.955723: P2P: Removing pending group interface p2p-wlan0-0
...
1319574736.648378: wlan0: P2P: Starting GO Negotiation with previously
authorized peer
...
1319574736.650115: wlan0: P2P: Sending GO Negotiation Response
...
1319574736.988038: wlan0: P2P-GO-NEG-SUCCESS
1319574736.988233: P2P: No pending group interface
1319574736.988268: P2P: Create a new interface p2p-wlan0-1 for the group
Clear the WPS method to avoid this situation. I wasn't
able to test this though, but given the log I can only
assume this is how the situation happened.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
If P2P device expires while a GO Negotiation is in progress, currently
p2p->go_neg_peer is cleared without indicating GO Nego failure. This
will result in pending group interfaces to be left over. This patch will
indicate GO Negotiation failure and will remove any pending group
interfaces.
This patch addresses a corner case in GO-Negotiation case. Consider the
scenario where two devices A and B are in discovery stage and Device B
vanishes [moves out of range] when a connect is issued on the Device A.
Then Device A keeps on retrying the GO Negotiation Request till the
retry limit is reached. On reaching retry limit, the pending group
interface is removed. But suppose if the peer entry in the device list
expires before the retry limit is reached, then pending group interface
was not removed.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Invalid use of memcpy instead of memcmp in comparison resulted in the
GO interface address getting set incorrectly if the GO did not show up
in scan results anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
trace.h may end up including system header files that define offsetof,
so include the compatibility definition from list.h only after this.
Signed-hostap: Jouni Malinen <j@w1.fi>
HT_INFO_OPERATION_MODE_OP_MODE_MASK is used with variables in host
byte order, so it should not be claimed as le16.
Signed-hostap: Jouni Malinen <j@w1.fi>
This is a workaround for Windows 7 supplicant rejecting WPA msg 3/4
in case it used Secure=1 in msg 2/4. This can happen, e.g., when
rekeying PTK after EAPOL-Key Error Request (Michael MIC failure)
from the supplicant.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up the code a bit by not having to deal with theoretical
possibility of maximum number of EAP methods to be different between
various components in hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some static analyzers complain about memset with '0' value. This was
used correctly here, but since use of strdup is about as good an option,
use that to silence the invalid warnings.
Signed-hostap: Jouni Malinen <j@w1.fi>
This avoid incorrect errors from some static analyzers that do not like
memmove with pointers just after the end of a buffer even if the number
of bytes to move is zero.
Signed-hostap: Jouni Malinen <j@w1.fi>
All we really need is the family ID, and we can
get that with genl_ctrl_resolve() and then don't
need to worry about family/cache objects.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
If a P2P client associates with the group while it is
already associated, two member entries may be added to
the group which also confuses num_members counting.
Deal with this by removing the existing entry first
before adding a new one.
I think the way Reinette ran into this was due to our
tx_sync implementation in iwlagn, mac80211 might have
queued two association frames thinking the first one
just failed, but both only went out after the sync was
really successful (which tx_sync doesn't wait for).
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
The P2P_FIND command was failing if it was issued at the moment when
a scan operation was in progress. Avoid returning failure in this
case by scheduling the P2P find to start once the ongoing scan is
completed.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
WEXT is not really changing anymore and more or less all Linux
distros come with linux/wireless.h that is recent enough to
allow the driver wrappers to be build.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit c2ff13c533 broke this with a
copy-paste typo that ended up adding the Probe Request P2P IE into the
Beacon frame (i.e., Beacon frame had two P2P IEs while Probe Response
had none).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Avoid zero-length memset at the end of the buffer. This is not really
needed, but it makes the code a bit easier for static analyzers.
Signed-hostap: Jouni Malinen <j@w1.fi>
Avoid zero-length memset at the end of the buffer. This is not really
needed, but it makes the code a bit easier for static analyzers.
Signed-hostap: Jouni Malinen <j@w1.fi>
Explicitly validate data_len so that static analyzers do not get
confused about the padlen validation. This is not really needed, but it
makes the code a bit easier for static analyzers.
Signed-hostap: Jouni Malinen <j@w1.fi>
Explicitly validate seed_len to skip memset call with zero length
of copied data at the end of the buffer. This is not really needed,
but it makes the code a bit easier for static analyzers.
Signed-hostap: Jouni Malinen <j@w1.fi>
data->phase2_method cannot really be NULL if
eap_fast_init_phase2_method() returns success, but this construction
seems to be too difficult for some static analyzers. While this change
is not really needed in practice, it makes it easier to go through
warnings from such analyzers.
Signed-hostap: Jouni Malinen <j@w1.fi>
hapd->time_adv cannot really be NULL if hostapd_update_time_adv()
returns success, but this construction seems to be too difficult
for some static analyzers. While this change is not really needed
in practice, it makes it easier to go through warnings from such
analyzers.
Signed-hostap: Jouni Malinen <j@w1.fi>
md->curlen cannot indicate full buffer size here since the buffered
data is processed whenever the full block size of data is available.
Avoid invalid warnings from static analyzers on memcpy() outside the
buffer length by verifying that curlen is smaller than block size.
Signed-hostap: Jouni Malinen <j@w1.fi>
This function can fail in theory since the SHA-1 functions are
allowed to return an error. While this does not really happen in
practice (we would not get this far if SHA-1 does not work), it is
cleaner to include the error handling here to keep static analyzers
happier. [Bug 421]
Signed-hostap: Jouni Malinen <j@w1.fi>
This has been obsoleted by the more generic Linux WEXT (driver_wext.c)
support. The hostap and madwifi driver wrappers can now be used only
with hostapd. The old station interface remains available in releases up
to 1.x.
Signed-hostap: Jouni Malinen <j@w1.fi>
The driver wrappers broadcom, iphone, osx, and ralink have not been
maintained for a while and it does not look like they will be in the
future either. As such, remove them from the development branch. The
previous versions will be included in older releases up to 1.x.
Signed-hostap: Jouni Malinen <j@w1.fi>
Reassemble partial TLS records to make the internal TLS client
implementation more convenient for stream sockets.
Signed-hostap: Jouni Malinen <j@w1.fi>
The padding validation was done on the last padding-length octets in the
buffer which misses the first padding octet (the last octet is the
padding length). Fix the starting offset for the comparison loop to get
the first octet verified. [Bug 420]
Signed-hostap: Jouni Malinen <j@w1.fi>
Return number of user input bytes from tlsv1_record_receive() to
move this detail into the proper record layer processing. In addition,
ignore unknown content types at record layer and allow processing to
continue after warning level TLS alerts to provide minimal workaround
for closure alerts.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of trying to remember to add wpa_msg() calls for every possible
path where a STA becomes authorized or unauthorized, use
ap_sta_set_authorized() to send these events more consistently.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_msg() has to use hapd->msg_ctx instead of hapd as the context
pointer to work properly in wpa_supplicant AP mode.
Signed-hostap: Jouni Malinen <j@w1.fi>
Currently, there is no events over the control interface
when a AP disconnects a station due to inactivity. With
this patch, an "AP-STA-DISCONNECTED" event will be sent.
Signed-hostap: Nicolas Cavallari <nicolas.cavallari@lri.fr>
Use a driver_ndis.c specific initialization function to fill in the
wpa_driver_ops information to make it easier to modify struct
wpa_driver_ops in the future. Being able to build driver_ndis.c
with MSVC was the only reason for having to maintain the same order
of function pointers in struct wpa_driver_ops and for having to
update driver_ndis.c for all changes in that structure.
Signed-hostap: Jouni Malinen <j@w1.fi>
The GTK is renewed in the hostapd after a MIC attack dissassociation
without informing the driver, causing decryption failures. This patch
sends the new GTK/IGTK to the driver after it is updated by the hostapd.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
When the supplicant acts as a registrar to learn the access point
parameters send the credentials to the wpa_cli interface after
receiving the 7th message. This is needed for proper behavior with
wps_cred_processing set to 1 or 2.
Without this patch, after the 7th message you got the WPS-CRED-RECEIVED
notification without the credentials. This was because the cred_attr and
cred_attr_len were not filled in in the wps structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
In scan.c, merge a channel's noise value into the scan results. When
comparing scan results, compute the signal-to-noise ratio and use it
when available. Prefer a 5 GHz network if its SNR is really big (> 30)
or if its SNR is relatively close to the other network's.
Some stations have been reported to send EAPOL-Key Error Reports
indicating Michael MIC failures even when the cipher is not TKIP
(e.g., when the network is using only CCMP). Ignore such reports
to avoid starting TKIP countermeasures unnecessarily. This can
prevent certaint types of denial of service attacks by insiders,
but mostly this is to work around invalid station implementations.
Signed-hostap: Jouni Malinen <j@w1.fi>
The eloop timeout to stop TKIP countermeasures has to be canceled
on deinit path to avoid leaving bogus timeouts behind.
Signed-hostap: Jouni Malinen <j@w1.fi>
Converts from a string to a control request enum when input
from a control interface is received. Will be used by a
subsequent patch.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Control requests will be extended for non-EAP uses later, so it makes
sense to have them be generic. Furthermore, having them defined as an
enum is easier for processing internally, and more generic for control
interfaces that may not use field names. The public ctrl_req_type /
field_name conversion function will be used later by the D-Bus control
interface too.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Special processing is needed to handle EAP user request for
identity or password at the beginning of Phase 2 when the implicit
identity request is used. data->pending_phase2_req needs to be set
to an empty buffer in that case to avoid re-processing the previous
part of TLS negotiation when the user enters the needed information.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of hardcoding IEEE 802.11b rates to be disabled whenever
P2P support is built in and supported by the driver, do this only
when an interface is set to P2P mode (both when adding a new
interface and when changing the interface mode). This re-enables
use of IEEE 802.11b APs with CONFIG_P2P=y builds.
Signed-hostap: Jouni Malinen <j@w1.fi>
This function was used unconditionally if wpa_supplicant build
includes CONFIG_P2P=y. Adding a separate driver_ops for such use
is not really useful since the driver wrappers can do the same
internally. Remove this driver_ops and move matching functionality
into driver_nl80211.c which was the only driver wrapper using
this driver_ops callback.
Signed-hostap: Jouni Malinen <j@w1.fi>
nl80211_disable_11b_rates() function was supposed to use the 'disabled'
parameter to figure out whether to disable or re-enable 802.11b rates.
In addition, the driver deinit path was now ending up re-disabling the
enabled rates at the end of the deinit operations when the interface
type was forced back to station. Both of these issues are now fixed
and the 2.4 GHz band TX rate index is cleared properly when
wpa_supplicant is stopped.
Signed-hostap: Jouni Malinen <j@w1.fi>
disable_11b_rates() is called on interface addition,
but not on interface type change, resulting in 11b rates
enabled on p2p interfaces.
Signed-off-by: Eliad Peller <eliad@wizery.com>
This can be used to apply the no-CCK rule conditionally depending on
which frame is being sent. The no-CCK rule applies only for P2P
management frames while SA Query and FT use cases do not have similar
restrictions.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add a new attribute to specify whether to use CCK rate or not during
scan and sending management frames. This helps to send P2P probes
at non-CCK rate. This ensures that P2P probe request/response/action
frames are always sent at non-CCK rates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
This was included in the AP configuration parameters, but there has
been no way to set it to anything else than the default automatic
mode. Remove this parameter and just hardcode ERP determination to
follow the automatic mode.
The MS-CHAPv1 and MS-CHAPv2 RFCs specify that the password is a string
of "Unicode characters", which for Windows means UCS-2; thus the
password could be any even-length string of up to 512 bytes.
Instead of making the incompatible change of requiring the incoming
password to be UCS-2 encoded, assume the password is UTF-8 encoded and
convert it before using it in NtPasswordHash and
EncryptPwBlockWithPasswordHash.
Signed-off-by: Evan Broder <ebroder@mokafive.com>
The netlink event processing is delayed since they are only returned
after control returns to eloop. This can result in netlink down events
being processed at a point when the interface has is actually still
there (the first event on new interface is down) and that can result in
odd behavior especially when the resulting interface-disabled event is
delivered to AP mode interface with wpa_supplicant.
Work around this by filtering netlink down events if the matching
interface is up at the time the netlink event is processed. This fixes
an issue brought up by commit 36d84860bb.
hostapd_wpa_auth_conf() is called on uninitialized memory and the
conditional blocks in this function may leave some fields into
uninitialized state. This can result in unexpected behavior elsewhere
since some of the variables may be used without matching #ifdef
blocks. Fix this by zeroing the memory.
TPK will be needed to be able to generate FTIE MIC for the
teardown message, so maintain peer data for a bit longer in
case the teardown FTIE request comes back from the driver.
The Query Response Length Limit is not allowed to be zero when
this is sent by the AP. Use 0x7F to indicate that the limit is
based on maximum number of GAS fragments.
For P2P, the p2p_connect takes in device address argument to make a
connection. However the connected event AP-STA-CONNECTED comes with
interface address. The application listening on events would find it
difficult to map interface address to the p2p device address which is
provided for connection.
Append P2P Device Address to AP-STA-CONNECTED event for P2P Client
connection. This will help applications to easily map the P2P Interface
Address to P2P Device Address on CONNECTED event. For non-P2P case, it
will just print the usual STA MAC address alone.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
The persistent_reconnect configuration parameter was used to decide
whether to accept invitation to re-establish a persistent group.
However, this was not being advertised in the Group Capability bitmap.
Add the Persistent Reconnect bit based on this configuration to GO
Negotiation frames and Beacon/Probe Response frames from the GO.
Use the wpa_tdls_add_peer function to allocate TDLS peer structures.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Use capability information to decide whether to perform a given TDLS
operation internally or through mgmt-frame Tx.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Before commencing setup, add a new STA entry to the driver representing
the peer. Later during setup, update the STA entry using information
received from the peer.
Extend sta_add() callback for adding/modifying a TDLS peer entry and
connect it to the TDLS state machine. Implement this callback for the
nl80211 driver and send peer information to kernel.
Mark TDLS peer entries with a new flag and translate it to a
corresponding nl80211 flag in the nl80211 driver.
In addition, correct TDLS related documentation in the wpa_driver_ops
structure.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Record the capabilities and supported rates of the TDLS peer during
link setup. These are given in the IEs passed in Setup Request and
Setup Response frames.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Disable the direct connection when a TDLS peer stops responding
to packets, as indicated by the "LOW ACK" event coming from a driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Allow sending a TDLS discovery request as a frame through the driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
When a driver does not implement the TDLS_TEARDOWN operation internally,
send an explicit TDLS link teardown frame to the driver.
Change all teardown calls to use these calling semantics.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Register for the TDLS discovery response public action frame in nl80211.
Print out a debug message when a Discovery Resp frame is received and
validated.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
When a discovery request is received, add the peer to the TDLS peer
cache and send a response containing minimal data. Mandatory IEs in
the discovery response frame will be filled out by the driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Put glue code in place to propagate TDLS related driver capabilities to
the TDLS state machine.
If the driver doesn't support capabilities, assume TDLS is supported
internally.
When TDLS is explicitly not supported, disable all user facing TDLS
operations.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Allow passing high-level TDLS commands and TDLS frames to kernel
via new nl80211 commands.
Propagate TDLS related nl80211 capability flags from kernel and add them
as driver capability flags.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
A zero dialog-token is considered invalid by IEEE Std 802.11z-2010.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
This function is actually needed for quite a bit more than just
user space MLME implementation. The old comment here has not been
accurate for a long time, so get rid of it.
These driver_ops functions set_channel, set_ssid, set_bssid,
mlme_add_sta, and mlme_remove_sta were used with the user space
MLME implementation in wpa_supplicant. That was only for testing
purposes and was removed, but these driver_ops were forgotten.
Remove them now to remove confusing driver_ops definitions.
This code was used only with driver_test.c to allow MLME operations
in hostapd to be tested without having to use a real radio. There
are no plans on extending this to any other use than testing and
mac80211_hwsim has now obsoled the need for this type of testing.
As such, we can drop this code from wpa_supplicant to clean up the
implementation of unnecessary complexity.
Netlink sockets can be shared among all driver instances, saving lots
of sockets, spurious log messages, memory, and CPU usage when using
multiple interfaces in a single process.
This offloads the station polling to driver wrappers, which may offload
it again to the driver. The hostap driver wrapper uses "real" data
frames while nl80211 uses null data frames.
Also add a specific event to indicate that a poll was successful for
future use with the nl80211 driver.
Some dualband cards can use more than five seconds to run through
a full scan, so increase the timeout to avoid hitting the missing
scan completed event workaround.
This fixes an issue where WPS run leaves a small ClientTimeout
value (2) configured and the next EAPOL authentication is started
with that small value even for Identity exchange. This can cause
problems when an EAPOL packet gets dropped immediately after
association and a retry of that packet is needed (which may take
more than two seconds).
This function can be used to clean up local UNIX domain socket files
that may be left over from clients that were previously connected to
wpa_supplicant. At least for now, this is only available for Android
builds.
Remove the separate driver_ops functions set_cts_protect(),
set_preamble(), set_short_slot_time(), and set_ht_params(). These
belong into same set of operations as set_ap(), so there is no need
to maintain separate functions that just make the driver wrapper
more complex.
Since these have only been used with driver_nl80211.c, the driver_ops
can be removed immediately instead of maintaining backwards
compatibility period with the old functions.
The AP client isolation parameter is now available through set_ap().
driver_nl80211.c was the only driver wrapper using the set_intra_bss()
call in hostap.git, but some external trees may have used this. Once
those are cleared, the set_infra_bss() driver_ops can be removed
completely. The only remaining use case for it currently is in P2P
GO mode with wpa_supplicant.
AP mode operations were used for P2P device discovery Listen state
only during early experiments. This has now been cleaned up and
ieee802_11_set_beacon() is not called for P2P device discovery.
As such, this hack to skip Beacon configuration can be removed.
This is the first step in allowing SA Query mechanism in hostapd to be
used with drivers that implement authentication and association MLME/SME
(i.e., do not use ieee802_11.c).
This adds the basic mechanism for running through network selection:
scan, ANQP fetch, network selection, and connection. Actual rules for
network selection and the creation of the network block are still
missing, but will be added in separate commits.
"hostapd_cli ess_disassoc (STA addr) (URL)" can now be used to send
an ESS Dissassociation Imminent notification to the STA. This event
is shown in wpa_supplicant ctrl_iface monitors (e.g., wpa_cli):
"WNM: ESS Disassociation Imminent - session_info_url=http://example.com/session/"
The new wpa_supplicant.conf file global parameters interworking and
hessid can be used to configure wpa_supplicant to include
Interworking element in Probe Request frames.
Commit 17f6b90056 moved the concatenation
of WPS IEs, but did not include the validation that the IE buffer is not
NULL. In addition, the concatenation needs to be done based on the full
IE buffer instead of the parsed pointer that includes only a single
WPS IE.
The base64 encoded data cannot included pad characters in the middle, so
we can stop the loop at the first sequence of pad characters. If the
sequence includes more than two pad characters, the encoding is invalid
and we can indicate failure.
Use the SSID filter list passed in the scheduled scan request down to
the kernel driver, so it can use the list to return only the wanted
SSIDs. Some kernel drivers can use this information to offload the
SSID filter to the hardware, helping with reducing the power
consumption.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Pass SSIDs to be matched in scheduled scan results. Only the SSIDs
that are included in the match lists will be reported by the driver,
so the filtering can be offloaded to the hardware and the power
consumption can be reduced.
Signed-off-by: Luciano Coelho <coelho@ti.com>
With scheduled scan support, we may need to pass more than 10 SSIDs in
a single scan request. Some drivers (e.g., wl12xx) support up to 16
SSIDs at once.
Change WPAS_MAX_SCAN_SSIDS from 10 to 16.
Signed-off-by: Luciano Coelho <coelho@ti.com>
In new Linux kernel versions (>=3.0), nl80211 adds scheduled scan
capability. In order to use this feature to its full extent, we need
to support it in the wpa_supplicant core, so that it can also be used
by other drivers.
This commit adds initial scheduled scan support operations and events.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Commit 19ec1f262e tried to fix some
cases for history prev selection, but it broke others. Fix this
properly by using a separate entry for the current edit line that
is not yet in history buffer.
Currently the P2P Interface name[p2p-%s-%d] is reset when the P2P
Interface name reaches the "IFNAMSIZ" limit. Monitor interface name is
derived from p2p interface name with the addition of few characters
[mon.p2p-%s-%d] and hence Monitor interface name hits IFNAMSIZ limit
before P2P Interface name. Rename the monitor interface name to
mon-%s-%d to reduce the length to same with p2p-%s-%d.
Data path for stations that get successfully associated to the
hostapd but fail to get added in the driver/firmware, will not
work. In such cases, hostapd should deauth and disconnect such
stations. In such scenario, hostapd should disconnect the STAs.
Sample output with following patch
wlan0: STA 0c:74:c2:9a:4c:59 IEEE 802.11: authenticated
wlan0: STA 0c:74:c2:9a:4c:59 IEEE 802.11: associated (aid 1)
wlan0: AP-STA-CONNECTED 0c:74:c2:9a:4c:59
wlan0: STA 0c:74:c2:9a:4c:59 IEEE 802.11: Could not add STA to kernel driver
wlan0: STA 0c:74:c2:9a:4c:59 IEEE 802.11: deauthenticated due to local deauth request
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
The password_hash parameter was not copied in case of the integrated
authentication server (but was for RADIUS server). This broke EAP
authentication when the user entry used NT-hash.
This currently unused function would have triggered wpabuf overflows
due to incorrect variable being reset to zero in the case the old
NoA wpabuf was large enough for the new data.
The EAPOL authenticator was previously forcing disconnection in the WPS
use case. However, this can be benefitial operation with any IEEE 802.1X
authentication mechanism and need not be limited to WPS. This helps some
use cases like EAP-FAST where provisioning may require two
authentication runs if the authentication server does not allow the PAC
provisioning step to be used for normal data connection. While the
station would be free to decide to re-associate in such a case, not all
stations do and as such, it helps if the AP does that instead of leaving
the association up with EAPOL state machine in HELD state for 60
seconds.
While EAP-FAST uses protected success notification, RFC 5422, Section
3.5 points out a possibility of EAP-Failure being sent out even after
protected success notification in case of provisioning. Change the
EAP-FAST peer implementation to accept that exception to the protected
success notification. This allows the station to re-connect more quickly
to complete EAP-FAST connection in the case the server rejects the
initial attempt by only allowing it to use to provision a new PAC.
If GO Negotiation Request (or in theory, also GO Negotiation Response)
frame is delivered multiple time for processing, the SSID of the group
could end up getting changed. This could result in possible issues if
the peer ended up using different SSID. To avoid this, make sure the
SSID does not get changed unless the negotiation is for a new group.
Whenever PMK gets changed (e.g., due to re-authentication), all PMKSA
caching entries that were created using the previous PMK needs to be
replaced. Previously, only the entry for the current AP was cleared.
Flush the other entries based on network_ctx matches to get rid of the
OKC entries. These entries can then be re-creating using OKC with the
new PMK.
When polling a station that has been inactive for a while, hostapd currently
always uses a null data frame. This is a bit strange with uAPSD clients
(though it seems to mostly work) since the EOSP bit can never be set in a
non-QoS frame. Make hostapd use QoS null data frames for probing when the
station is a QoS STA.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wrap self-generated WPS credential for new AP settings and send that to
control interface to provide the needed information in
WPS-NEW-AP-SETTINGS for external processing.
GAS/ANQP is a generic protocol and in no way specific to P2P, so move
routines used to build GAS/ANQP frames to a separate file that can be
shared for other uses than just P2P service discovery.
The new function, p2p_scan_ie_buf_len(), can be used to figure out
how large a buffer needs to be allocated for p2p_scan_ie() use. This
makes it easier to add new data into the buffer without forcing all
callers to be updated to use a larger buffer.
The P2P search mechanism depends on the same scan functionality that
is used for station mode scans. If these operations are being used
at the same time, scan result processing is not handled properly.
Avoid unexpected behavior by delaying station mode scan requests
if a P2P operation is in progress.
Among other things, this allows the station mode connection attempt
to be continued after a P2P find or group formation has been completed
if the interface is available (i.e., when the P2P group uses a
separate virtual interface).
If the initial attempt to start a scan for p2p_find fails, an error
is reported. However, the P2P scan handler and search state was
left behind. That can result in unexpected behavior when the next
non-P2P scan results are indicated. Avoid this by clearing the
P2P search state on failure.
This new flag can be used to change wpa_supplicant behavior in the
default ap_scan=1 mode to move BSS selection into the driver (likely
firmware). This commit is only adding the flag; separate commits
will be used to change the actual connection/roaming behavior.
These protocols seem to be abandoned: latest IETF drafts have expired
years ago and it does not seem likely that EAP-TTLSv1 would be
deployed. The implementation in hostapd/wpa_supplicant was not complete
and not fully tested. In addition, the TLS/IA functionality was only
available when GnuTLS was used. Since GnuTLS removed this functionality
in 3.0.0, there is no available TLS/IA implementation in the latest
version of any supported TLS library.
Remove the EAP-TTLSv1 and TLS/IA implementation to clean up unwanted
complexity from hostapd and wpa_supplicant. In addition, this removes
any potential use of the GnuTLS extra library.
This fixes some build issues in GnuTLS wrapper to be compatible with
at least following GnuTLS versions: 2.2.5, 2.4.3, 2.6.6, 2.8.6,
2.10.5, 2.12.11, 3.0.3.
Instead of using separate bad_record_mac and decryption_failed alerts,
use only bad_record_mac alert regardless of how the CBC decryption
failed. This provides less information to attackers that could modify
packets. In addition, instead of returning immediately on error, run
through the MAC check to make timing attacks more difficult.
When the received data will be decrypted, there is no need to first
copy it and then handle decryption in-place when decryption step can
take care of both operations.
TLS v1.0 and v1.1 RFCs were not exactly clear on the use of the
protocol version in record later. As such, accept any {03,xx} value
to remain compatible with existing implementations and new protocol
versions.
The p2p->drv_in_listen variable is used to track Listen state operations
in the driver. This is cleared when the driver reports that the Listen
state has ended (p2p_listen_end() gets called). However, it is possible
that the driver does not indicate that if the Listen state is canceled.
This can apparently happen in some cases where p2p_connect command is
issues while the Listen state is in progress.
Work around this issue by clearing p2p->drv_in_listen when Listen state
is stopped as part of p2p_stop operation. This allows the P2P module to
process CONNECT_LISTEN timeout in p2p_timeout_connect_listen() to move
to CONNECT state, e.g., when starting GO Negotiation after Device
Discoverability mechanism.
The "too long" buffer (32+1 octets) prevented AP from starting up with
32 octet SSID with WE-21 and newer. Fix this by reducing the
SIOCGIWESSID buffer length.
This adds support for RSN pre-authentication with nl80211 interface and
drivers that handle roaming internally (i.e., wpa_supplicant is not
responsible for requesting scan results that provide the needed
information without these events).
cfg80211 does not currently allow NL80211_CMD_CONNECT when there
is already an association. This can result in wpa_supplicant being
unable to request a connection if the interface is already in
connected state. Work around this by requesting disconnection if
the connect command fails with EALREADY error. This allows
wpa_supplicant to recover from the unexpected state and complete
the connect request on next attempt.
eapol_test command line argument -o<file> can now be used to request
the received server certificate chain to be written to the specified
file. The certificates will be written in PEM format. [Bug 391]
Make the WPS processing of (Re)Association Request frame IEs conditional
on WPS support. This fixes a build issue with wps_is_20() not being
defined and makes the non-WPS build a bit smaller.
os_*() wrappers should be used instead of functions from time.h.
Removing the header from includes.h enforces this. os_unix.c can
include this its uses are valid wrapper calls. wps_upnp.c uses
gmtime() for which there is no os_*() wrapper available yet, so
allow it to use time.h, too. Similarly, allow dump_state.c to
use time.h for ctime().
Currently, the following can happen:
1) P2P state machine requests R-O-C
2) user changes their mind and aborts
3) P2P state machine aborts R-O-C
4) driver_nl80211 rejects abort since there
was no notification about the start yet
5) R-O-C period start notification from kernel
6) P2P state machine requests new R-O-C
7) this overlaps with old R-O-C -- iwlwifi driver
can't handle that and returns -EBUSY
8) state machine stops dead in its tracks
The reason is that the abort isn't going through properly. Instead of
tracking whether a R-O-C is active in driver_nl80211, track whether one
was requested to avoid this scenario.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers to disable CCK rates from Probe Request frames.
For nl80211, this is currently applying only to the supported rates
element(s), but this mechanism could be extended to address TX rate
control masking, too, to lessen need for global rate disabling.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Since the kernel can now advertise P2P concurrent support by advertising
interface combinations, we can take advantage of that and automatically
use P2P_CONCURRENT / P2P_MGMT_AND_NON_P2P for drivers that advertise
support.
Keep driver_param=use_p2p_group_interface=1 for anyone not advertising
interface combinations in their drivers yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The default config methods was hardcoded to claim support for
PushButton, Display, and Keypad. While these are supported by
most P2P devices, there may be some cases where it is convenient
to be able to disable a specific config method. Use config_methods
configuration parameter to set the default values for Config Methods
in the P2P Device Info attribute.
The P2P specification (3.1.4.3) disallows use of the Label configuration
method between two P2P devices. This was previously enforced at upper
level, but the obsolete code can be removed from wpa_supplicant. This
adds a bit more strict enforcement of the policy, but should not result
in practical differences since no known P2P implementation uses Label
config method.
If a network configuration block is removed or modified, flush
all PMKSA cache entries that were created using that network
configuration. Similarly, invalidate EAP state (fast re-auth).
The special case for OKC on wpa_supplicant reconfiguration
(network_ctx pointer change) is now addressed as part of the
PMKSA cache flushing, so it does not need a separate mechanism
for clearing the network_ctx values in the PMKSA cache.
If the driver maintains its own copy of the PMKSA cache, we need to
clear an entry from the driver whenever wpa_supplicant is dropping
an old PMKSA cache entry.
The Deauth/Disassoc TX status callbacks were ending up kicking the
station entry from kernel driver when test functionality was used to
inject Deauth/Disassoc frames from the AP with the purpose of leaving
the local association in place. Fix this by using STA flags to figure
out whether there was a pending callback for the frame that we need
to act on.
In addition, add forgotten functionality for the Disassoc TX status
callback to match the behavior with Deauth.
The previous code was trying to figure out which WPA version is
used based on the extra IEs requested for Association Request. That
did not work properly in cases where non-WPA networks are used with
some extra IEs. Fix this by using more robust mechanism for passing
the WPA versions from core wpa_supplicant to the driver_ops
associate().
Instead of hardcoding the Config Methods attribute value in Probe
Request frames, set this based on the configured parameter
config_methods to allow correct set of methods to be advertised.
The device description file may include multiple devices. Improve the
simplistic parser by first trying to find the WFADevice:1 device before
fetching the device parameters. While this is still far from complete
XML parsing, this should address the most common root device
specifications.
This allows non-mac80211 drivers to report received Probe Request
frames to user space and Probe Response and Action frames to be sent
from user space when using AP/P2P GO mode.
This allows the driver to use PS buffering of Deauthentication and
Disassociation frames when the STA is in power save sleep. The STA
entry (and PTK) will be removed from the kernel only after the
Deauth/Disassoc has been transmitted (e.g., when the STA wakes up).
A hardcoded two second timeout is used to limit the length of this
window should the driver fail to deliver the frame (e.g., the STA
is out of range and does not wake up). The kernel STA entry is
marked unauthorized during the wait to avoid accepting Data
frames from the STA that we have decided to disconnect.
This behavior is available only with drivers that provide TX status
events for Deauth/Disassoc frames (nl80211 at this point). Other
drivers continue to use the previous behavior where the STA entry
is removed immediately.
Extend the code that waits for the station to send EAPOL-Start before
initiating EAPOL authenticator operations to cover the case where the
station includes WPS IE in (Re)Association Request frame if that IE
does not include support for WPS 2.0. While this should not really
be needed, this may help with some deployed WPS 1.0 stations that do
not support EAPOL operations correctly and may get confused of the
EAP-Request/Identity packets that would show up twice if EAPOL-Start
is transmitted.
If an ER tries to send a message to a STA that is not in the middle
of WPS protocol, do not try to deliver that. This can help with issues
where an ER takes long time to reply to M1 and another Registrar has
already completed negotiation.
It is possible to get a response for a pending EAP callback after the
EAP state machine has already completed its work or has timed out. For
those cases, make sure that the callback function is not delivered since
it could result in NULL pointer dereferences.
The Config Methods attribute in M2 and M2D messages is supposed to
indicate which configuration methods are supported by the Registrar. As
such, it should not depend on whether PBC mode is currently active or
not. That will only affect the Selected Registrar Config Methods and
Device Password ID attributes.
This change is a first step in better supporting different driver
architectures for AP mode operations with nl80211. This commit in
itself does not add new functionality, but it makes it easier to add
new AP mode parameters to address needs of drivers that have more of
the MLME/SME in firmware or kernel.
Split WPA initialization into two parts so that the Beacon frames can be
configured fully before the initial keys (GTK/IGTK) are configured. This
makes it easier for drivers that depend on the AP security mode being
fully set before the keys are configured.
This avoids a request to the driver to first start beaconing before
the WPA/RSN IE has been generated and then immediately changing the
beacon IEs once the WPA/RSN IE is ready.
Such using params->wpa_ie to figure out whether the connection is for
WPA/WPA2 is not correct since that buffer is used also to add WPS IE. In
case of WPS, do not add NL80211_ATTR_WPA_VERSIONS to avoid confusing
drivers.
Some compilers complain about fwrite calls if the return value is
not checked, so check the value even if it does not really make
much of a difference in this particular case.
The internal TLS implementation assumes that the certificate chain
is ordered by issuer certificate following the certificate that it
signed. Add the certificates to the chain in suitable order when
loading multiple certificates.
Commit e1d526293b added code for verifying
whether the receive Probe Request frame was indicating support for only
802.11b rates, but it missed the for loop for the extended supported
rates element. Add that to fix the validation code for cases where
non-802.11b rates are in the extended supported rates element.
Currently, wpa_driver_nl80211_authenticate() changes the interface type
to station. However, in case of P2P, we need to change the interface
type to P2P_CLI.
Add p2p field to the authentication params, and consider it for choosing
the correct interface type.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Commit 9f51b11395 added support for P2P
interfaces when adding a new interface. However, it didn't handle the
case in which the same interface is being used and its type is being
changed. Add support for this case.
Consequently, when doing "ap_scan_as_station" we now need to save the
actual AP interface type (AP/P2P GO) in order to restore it properly.
For that, change ap_scan_as_station type from int to nl80211_iftype, and
set it to NL80211_IFTYPE_UNSPECIFED when not used.
Signed-off-by: Eliad Peller <eliad@wizery.com>
When driver_nl80211.c has to set the netdev down to change iftype, an
RTM_NEWLINK event is generated. Do not generate
EVENT_INTERFACE_DISABLED event based on that.
Reassociation Request/Response frame validation need to count all IEs in
the RIC. In addition, TIE is not protected, so it should not be included
in the count.
Signed-off-by: Hong Wu <hong.wu@dspg.com>
Only accept Probe Request frames that have a Wildcard BSSID and a
destination address that matches with our P2P Device Address or is the
broadcast address per P2P specification 3.1.2.1.1.
When a new interface is created and already has a separate MAC address
assigned by the kernel, then we need to use that address, not just when
we've created a locally administered address.
This fixes use_p2p_group_interface=1 for iwlagn as it already makes
mac80211 assign an address for a second interface since the hardware has
two addresses assigned.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to wpa_supplicant for device-based GTK rekeying. In order to
support that, pass the KEK, KCK, and replay counter to the driver, and
handle rekey events that update the latter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Send STA flags to kernel when adding a new station. This ensures
stations are added with up to date flags by kernel drivers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
When adding a new station, set the STA flags as part of the sta_add()
command. This ensures the flags are up to date when the station is added
by lower level drivers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
A new hostapd configuration parameter, disable_pmksa_caching=1, can now
be used to disable PMKSA caching on the Authenticator. This forces the
stations to complete EAP authentication on every association when WPA2
is being used.
In general, this patch attemps to extend commit
00468b4650 with dbus support.
This can be used by dbus client to implement subject match text
entry with preset value probed from server. This preset value, if
user accepts it, is remembered and passed to subject_match config
for any future authentication.
Signed-off-by: Michael Chang <mchang@novell.com>
Data path is broken when hostapd reloads its configuration
disabling the security which was previously enabled (WEP/WPA),
using kill -1, as old keys were not cleared.
The patch clears the keys configured when hostapd reloads
its configuration.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
This phase1 parameter for TLS-based EAP methods was already supported
with GnuTLS and this commit extends that support for OpenSSL and the
internal TLS implementation.
Fix a bug with the current dev_found()/dev_lost() usage. Previously
in p2p_device_free() dev_lost() was invoked for devices that had
not been dev_found(). This caused dbus related msgs to stderr like:
"Attempted to unregister path (path[0] = fi path[1] = w1) which isn't
registered"
Signed-off-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
Some P2PDevice properties were not updated in p2p->cfg structure:
reg_class, channel, op_reg_class, and op_channel. Hence, update p2p->cfg
parameters through p2p core calls in wpas_p2p_update_config().
Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
Move level parameter from p2p_device to p2p_device_info in order to
expose this information and modify D-Bus P2P handler to return this new
parameter through the P2P device properties.
Signed-off-by: Fabien Marotte <fabienx.marotte@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
Previously hostapd just masked the STAs HT caps with its own. However,
some HT caps are not symmetric and as such need to be handled
different.
hostapd shouldn't overwrite the STAs SMPS mode as otherwise the driver
cannot know it has to use RTS/CTS to wake the receiver from dynamic
SMPS for MCS rates > 7.
hostapd shouldn't mask the RX and TX STBC caps with it's own. They are
already handled in a special case below.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
This file is a part of the radiotap parser that Andy Green agreed to
relicense under the BSD license (per email, 11 Aug 2007 07:42:05
+0100). The copyright/license statement was updated in radiotap.c,
but this radiotap_iter.h file was forgotten at that point.
In set_key handler, the seq[8] is in little endian order defined by
WPA. BSD kernel uses a u_int64_t value ik_keyrsc to represent it
internally. The kernel expects the native endian order for the value.
Thus, we need to detect the endian order and swap bytes when
necessary.
This fixes an issue with SA Query Response frames not being processed
anymore after wpa_supplicant started registering a handler for those.
This handler registration is in generic driver_nl80211.c code, so
hostapd uses it, too.
Implement PMKSA cache operations add, remove, and flush using nl80211
commands NL80211_CMD_{SET,DEL,FLUSH}_PMKSA to support PMKSA caching
with drivers that select the AP and generate the RSN IE internally.
When provision discovery fails, this new callback will be called
so P2P users can react to the failure.
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the peer may not be in Listen state when the provision discovery
request is sent, try to send the request again number of times when in
IDLE state. This was already done when p2p_find is in progress, but this
commit adds retries to the case where no other P2P operations are in
progress.
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used to avoid rejection of first two 4-way handshakes every
time hostapd (or wpa_supplicant in AP/IBSS mode) is restarted. A new
command line parameter, -e, can now be used to specify an entropy file
that will be used to maintain the needed state.
Some of these are required for proper functionality (like
get_seqnum); others may not be needed yet, but including them
allows some extra ifdef/endif blocks to be removed.
.set_rate_sets is not defined for non-hostapd, which prevents
configuring basic_rates when working as P2P GO.
Signed-off-by: Eliad Peller <eliad@wizery.com>
If the driver wrapper is setting up the interface up only at commit(),
UPnP initialization fails. Fix that by moving UPnP setup to happen after
the driver commit() call.
Windows 7 uses incorrect way of figuring out AP's WPS capabilities by
acting as a Registrar and using M1 from the AP. The config methods
attribute in that message is supposed to indicate only the configuration
method supported by the AP in Enrollee role, i.e., to add an external
Registrar. For that case, PBC shall not be used and as such, the
PushButton config method is removed from M1 by default. If pbc_in_m1=1
is included in the configuration file, the PushButton config method is
left in M1 (if included in config_methods parameter) to allow Windows 7
to use PBC instead of PIN (e.g., from a label in the AP).
cfg80211 maintains separate BSS table entries for APs if the same
BSSID,SSID pair is seen on multiple channels. wpa_supplicant does
not use frequency as a separate key in the BSS table, so filter out
duplicated entries. Prefer associated BSS entry in such a case in
order to get the correct frequency into the BSS table.
It may take some time for the TX status to be delivered for a
(Re)Association Response frame and if any Data frames are received
during that time, they may end up getting dropped as Class 3 frames in
not-associated state. This results in a Disassociation frame being sent
to the station and it assuming that the association has been lost.
Work around the issue by remembering that the (Re)Association Request
has already been accepted and skip the Deauth/Disassoc sending because
of the possible Class 3 frames before the TX status callback is
received.
In theory, these calls could fail, but it is not really likely to
happen in practice in the use case here. Anyway, check that they do
not return an error before accepting the length of the file.
This function does not get called with in_data == NULL in practice, but
it seems to be at least partly prepared for that case, so better make it
consistent by handling the NULL value throughout the function.
Both the SA and IEs from the received Probe Request frames must be
included and the Probe Request RX callback functions may assume that
these are not NULL.
The change to use wpa_dbg() in wpa_sm_parse_own_wpa_ie() could result
in a NULL pointer dereference if the function were called when WPA
state machine has not been initialized. While this cannot really
happen in practice, it is better to be prepared for that since that
was the case before the wpa_dbg() change.
The size_t value here can be 64-bit and result in implicit sign
extension. In this particular case, that gets masked out by
host_to_be32(), so there is no practical difference, but it is better
to get rid of the 64-bit variable explicitly.
The supportedTypes parameter is a list of TNC_MessageType values
and the buffer to be copied should use size of TNC_MessageType, not
TNC_MessageTypeList. In practice, these are of same length on most
platforms, so this is not a critical issue, but anyway, the correct
type should be used.
This avoids reading past the end of the IE buffer should the FTIE
be too short. In addition, one debug hexdump was using uninitialized
pointer to the FTIE buffer, so fixed it to use the pointer from the
parse data.
AF_INET6 is not always enabled by default, so use AF_INET instead. In
addition, use the old fixed length, 2048, as a failover value if the
sysctl fails for any reason.
Commit 03d3f28a69 broke initialization of
EAPOL authenticator state machines since an error value from
wpa_auth_sta_key_mgmt() (-1) was not handled properly and the fixed
wpa_key_mgmt_wpa_psk() identified the value as a PSK-based AKM because
of all bits being set to 1. The special error value needs to handled
separately to avoid skipping EAPOL state machine initialization.
These can be used in some cases with a bitfield having multiple
AKMs enabled (e.g., WPA-PSK and WPA-PSK-SHA256). Address those
cases by checking whether any of the matching AKM are included.
When the SME is in the driver or cfg80211, the automatic selection
of auth_alg is done by leaving out the NL80211_ATTR_AUTH_TYPE
attribute from the NL80211_CMD_CONNECT command.
This should fix EAPOL reauthentication and rekeying timeout issues
with Intel clients when using WMM (e.g., with IEEE 802.11n). These
stations do not seem to be able to handle EAPOL data frames as
non-QoS Data frames after the initial setup.
This adds STA flags to hapd_send_eapol() driver op to allow
driver_nl80211.c to mark the EAPOL frames as QoS Data frame
when injecting it through the monitor interface.
This provides a means for the supplicant to directly request signal
quality metrics from the driver. This is useful, for example for
background scan algorithms that might ask desire this information
out-of-band with CQM events.
Signed-off-by: Paul Stewart <pstew@google.com>
When building IE from an empty string and CONFIG_WPS_STRICT is
not defined, redundant 2 bytes are being added to the string.
We have to return right after building the "dummy" string.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Some deployed supplicants update their SNonce for every receive
EAPOL-Key message 1/4 even when these messages happen during the
same 4-way handshake. Furthermore, some of these supplicants fail
to use the first SNonce that they sent and derive an incorrect PTK
using another SNonce that does not match with what the authenticator
is using from the first received message 2/4. This results in
failed 4-way handshake whenever the EAPOL-Key 1/4 retransmission
timeout is reached. The timeout for the first retry is fixed to
100 ms in the IEEE 802.11 standard and that seems to be short
enough to make it difficult for some stations to get the response
out before retransmission.
Work around this issue by increasing the initial EAPOL-Key 1/4
timeout by 1000 ms (i.e., total timeout of 1100 ms) if the station
acknowledges reception of the EAPOL-Key frame. If the driver does
not indicate TX status for EAPOL frames, use longer initial
timeout (1000 ms) unconditionally.
Store Manufacturer, Model Name, Model Number, and Serial Number
attributes for P2P peers and expose these through the existing
peer information mechanisms.
Previously, a bug in GKeyDoneStations count would remain in effect
until the authenticator is restarted. Make this more robust by
clearing the station count before each rekeying setup. While this
is not really supposed to be needed, there has been bugs in this
area in the past and it is safer to make the implementation recover
from such an issue automatically.
If the STA to be freed is still included in GKeyDoneStations count,
decrement the count when the STA is freed. This does not happen in
AP mode since there is enough time to go through the authenticator
state machine to clear the STA. However, in the current RSN IBSS
implementation, the authenticator state for the STA is freed in a
way that does not allow the state machine to go through the clearing.
To address this, make sure that wpa_free_sta_sm() decrements the
GKeyDoneStations count if the STA happened to be in the process of
GTK rekeying.
CFLAGS += -DCONFIG_RSN_TESTING in .config and rsn_testing=1 in
hostapd.conf can now be used to enable a testing mode that adds
extensions to RSN element. This can be used to check whether
station implementations are incompatible with future extensions
to the RSN element.
The AP code might, currently only in the case of HT40, defer actual
enabling to after a scan. In this case, the wpa_s AP code gets confused.
Add a callback for it to use and make it use it to finish only when the
setup has actually completed.
With appropriate hacks in place this allows using HT40 in P2P mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the P2P code keep track of WPS vendor extensions received from
peers so they can be exposed via DBus later.
Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds the ability to add WPS vendor extension attributes in P2P
frames, like GO Negotiation and Probe Response frames.
Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds the ability to add WPS vendor extensions to an AP (or GO).
They will be added to the WSC IE(s) in Beacon and Probe Response frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of converting back and forth from the string representation,
always use the binary representation internally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use only the UUID-E to remove active PBC session(s) at the completion of
successful PBC protocol run. This fixes potential issues with Enrollees
that use multiple MAC addresses and as such, can get multiple entries in
the PBC session list.
Add Secondary Device Type List attribute in WSC IE for P2P
Probe Response frames if one or more secondary device types
are configured.
Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The secondary device type list is an optional attribute in the WSC IE.
Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently hostapd will force HT Mixed Mode if at least one non-GF STA is
associated. This will force _all_ HT transmissions to be protected.
802.11n-2009 doesn't require HT Mixed Mode to be used in case of non-GF
STAs but instead the HT information element contains a flag if non-GF
STAs are present. All STAs are required to protect GF transmissions in
that case. Hence, setting HT Mixed mode if non-GF STAs are present is
superfluous.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Use a specific return value, WPS-PBC-OVERLAP, to indicate a reason
for rejecting a wps_pbc command in wpa_supplicant AP mode if the
PBC mode cannot be started due to PBC session overlap having been
detected during monitor time.
This allows the user to complete WPS provisioning using PBC by
selected a specific Enrollee even if there are other Enrollees
in active PBC mode at the same time. The other Enrollees will be
rejected should they try to connect at the same time.
Ignore possible mismatches in the source address of the frame and only
use UUID-E to check whether a Probe Request or M1 is from the same
Enrollee when figuring out whether there is PBC session overlap. This
is needed to avoid potential issues with Enrollee devices that may have
multiple interfaces indicating active PBC state.
If there is already a link the requested peer, request start of
renegotiation instead of completely new link. This seems to be needed
to allow some driver to accept the trigger for a new negotiation.
tdls_testing 0x80 can now be used to request wpa_supplicant to send
a TDLS Setup Request frame (i.e., try to initiate TDLS setup)
whenever a TDLS Setup Request frame has been received from a peer.
Blindly clearing all struct wpa_tdls_peer members is a risky
operation since it could easily clear pointers to allocated
memory, etc. information that really should not be removed.
Instead of hoping that new code gets added here to restore
the important variables, reverse the approach and only clear
structure members one by one when needed.
This allows the same code path to be used for both protected and
unprotected configurations to limit need for duplicated code in
both the driver and wpa_supplicant.
This adds code for validating that the same Key Lifetime is used
throughout TPK handshake and enables TPK lifetime expiration and
renewal/teardown. These part seem to be working, but the actual
handling of TDLS Setup Confirm and renewal are not fully
functional yet.
tdls_testing bits:
bit 3 = use short TPK lifetime (301 seconds)
bit 4 = use wrong TPK lifetime in TDLS Setup Response
bit 5 = use wrong TPK lifetime in TDLS Setup Confirm
These special test cases can be configured at run time with "wpa_cli
tdls_testing <value>" where <value> is an integer (either as a decimal
or as a hex value with 0x prefix) bitmap of special features with
following bits available at this point:
bit 0 = long frame (add dummy subelement to make FTIE very long)
bit 1 = use alternative RSN IE (different RSN capab value and no extra
replay counters)
bit 2 = send incorrect BSSID in Link Identifier of TDLS Setup Request
(e.g., 1 = long FTIE, 2 = different RSN IE, 3 = both of those)
This is disabled by default and can be enabled for the build by
adding the following line to .config:
CFLAGS += -DCONFIG_TDLS_TESTING
This allows driver wrappers to indicate whether the association was
done using Association Request/Response or with Reassociation
Request/Response frames.
CFLAGS += -DCONFIG_VALGRIND can now be used to enable support for
Valgrind client requests to help in removing some non-issues from
Valgrind reports. This is mainly aimed at allowing unknown ioctl
results to be marked as defined data.
If the os_time_t variable used for the expiration time (seconds)
overflows when the registered timeout value is being added,
assume that the event would happen after an infinite time, i.e.,
would not really happen in practice. This fixes issues with
long key timeouts getting converted to immediate expiration due
to the overflow.
os_snprintf() can be a preprocessor macro and according to
C99 (6.10.3 clause 11) the results of having preprocessor directives
inside the macro arguments is undefined.
Build options can now be used to replace the location of client
sockets for UNIX domain socket control interface:
CFLAGS += -DCONFIG_CTRL_IFACE_CLIENT_DIR=\"/tmp\"
CFLAGS += -DCONFIG_CTRL_IFACE_CLIENT_PREFIX=\"wpa_ctrl_\"
The buffer size for routing socket is fixed to 2048.
This patch fix it to obtain the size from OS.
This patch worked on x86 platform with NetBSD 5.0.2.
This allows keystore:// prefix to be used with client_cert and
private_key configuration parameters.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This will only retrieve information about peers that have been fully
discovered, not peers that are only half-discovered based on their Probe
Request frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The DBus code will want to have perfect matching of dev_found and the
dev_lost it adds so it doesn't need to keep track internally. Enable
that with a new flag in the core that tracks whether we have already
notified about this -- the existing users can ignore it.
The part where this is always set to 1 if the new device is discovered
by a driver that has P2P in the driver is buggy -- the driver should
feed the P2P peer database and then that should feed the notification
here instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This embeds some information about each P2P peer that will be publically
visible in a struct that is shared.
The dev_found notification function is also passed the new struct, which
requires some work for the driver-based P2P management.
Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Fabien Marotte <fabienx.marotte@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using multiple vifs and dynamic vlan tagging is enabled on any
interface, the created AP VLAN interfaces get the BSSID of the first
AP mode interface instead of the BSSID of the corresponding AP mode
interface.
Example:
wlan0 - xx:xx:xx:xx:x0
wlan1 - xx:xx:xx:xx:x1
Assume a STA connects to the AP interface wlan1 and gets a dynamic
VLAN tag 100 assigned by the RADIUS server. Hostapd will create an AP
VLAN interface wlan1.100 but doesn't set an address for this interface
which results in wlan1.100 getting the same address as wlan0:
wlan1.100 - xx:xx:xx:xx:x0
As a result the STA that was moved to wlan1.100 isn't able to finish its
4-way handshake since mac80211 won't pass its frames to wlan1.100 due to
the different address.
To fix this issue make use of the address of the AP interface when
creating an AP VLAN interface.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Add MAC addresses for stations and use wpa_msg instead of printf
methods to make it easier to grep logs and find messages for the
station in question.
Signed-off-by: Ben Greear <greearb@candelatech.com>
If parsing of the certificate or private key succeeds using any of
the tried encoding types, clear the OpenSSL error queue without
showing the pending errors in debug log since they do not really
provide any useful output and can be confusing.
This patch fixes a problem I had when I tried to connect
an embedded system [wpa_supplicant, CONFIG_TLS=internal]
to my TLS secured network.
TLSv1: Send CertificateVerify
TLSv1: CertificateVerify hash - hexdump(len=36): ha .. ha
PKCS #1: pkcs1_generate_encryption_block - Invalid buffer lengths \
(modlen=512 outlen=454 inlen=36)
It turned out that a fixed 1000 byte message buffer was just
a little bit too small for the 4096 bit RSA certificates
I'm using.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
In multi BSS setups it wasn't possible to set up an HT BSS in
conjunction with a WEP/TKIP BSS. HT needed to be turned off entirely
to allow WEP/TKIP BSSes to be used.
In order to allow HT BSSes to coexist with non-HT WEP/TKIP BSSes add a
new BSS conf attribute "disable_11n" which disables HT capabilities on a
single BSS by suppressing HT IEs in the beacon and probe response
frames. Furthermore, mark all STAs associated to a WEP/TKIP BSS as
non-HT STAs. The disable_11n parameter is used internally; no new entry
is parsed from hostapd.conf.
This allows a non-HT WEP/TKIP BSS to coexist with a HT BSS without
having to disable HT mode entirely. Nevertheless, all STAs associated to
the WEP/TKIP BSS will only be served as if they were non-HT STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Use l2_packet with Ethernet header included so that the source
address for RRB packets can be forced to be the local BSSID. This
fixes problems where unexpected bridge interface address may end
up getting used and the recipient of the frame dropping it as
unknown R0KH/R1KH.
This is needed to keep kernel and hostapd in sync. In addition,
the obsolete entry in hostapd prevented use of Deauthentication
or Disassociation frame with reason code 6/7 mechanism to indicate
to the STA that there is no association if the STA missed the
broadcast Deauthentication frame for any reason.
The internal pointer to RADIUS client configuration needs to be
updated whenever a new hostapd configuration is loaded. Without
this, freed memory may be dereferenced and this can result in
segmentation faults.
This converts number of debugging messages to use wpa_msg() in order
to allow the interface name to be shown with the messages.
A new function, wpa_dbg(), is introduced to allow
CONFIG_NO_STDOUT_DEBUG=y builds to remove the debug strings. This is
otherwise identical with wpa_msg(), but it gets compiled out if stdout
debugging is disabled.
This is needed to allows WPS PBC session overlap detection to work
with drivers that process Probe Request frames internally. This
code is is run in hostapd, but the wpa_supplicant AP mode did not
have call to the hostapd_probe_req_rx() function even though it
registered handlers for hostapd Probe Request RX callbacks.
An optional parameter, p2p_dev_addr, can now be given to WPS_PBC
command on P2P GO to indicate that only the P2P device with the
specified P2P Device Address is allowed to connect using PBC. If
any other device tries to use PBC, a session overlap is indicated
and the negotiation is rejected with M2D. The command format for
specifying the address is "WPS_PBC p2p_dev_addr=<address>", e.g.,
WPS_PBC p2p_dev_addr=02:03:04:05:06:07
In addition, show the PBC session overlap indication as a WPS failure
event on an AP/GO interface. This particular new case shows up as
"WPS-FAIL msg=4 config_error=12".
This makes log files much more readable if multiple interfaces
are being controlled by the same process. The interface name is
added to stdout/file/syslog entries, but not to the messages
sent to control interface monitors to avoid issues with parsing
in external programs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Add a callback for station's authorized transitions
to allow wpa_supplicant to emit events in DBus.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To enable making state change notifications on the WLAN_STA_AUTHORIZED
flag, introduce ap_sta_set_authorized(), and to reduce use of the flag
itself also add a wrapper for testing the flag: ap_sta_is_authorized().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver advertises max_remain_on_chan data, use it instead of
the hardcoded value of 5000. Keep the default at 5000 since that is the
value used by earlier versions of cfg80211/mac80211 and not advertised
in nl80211 for those.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When authenticating, and the interface type is not already
NL80211_IFTYPE_STATION, we need to call wpa_driver_nl80211_set_mode()
only once. Remove the excessive call.
Signed-off-by: Eliad Peller <eliad@wizery.com>
We need to call this function after having completed the neighboring
channel scan to figure out whether HT40 can be used and if so, which
channel is the secondary channel.
ieee80211n_supported_ht_capab is called after ieee80211n_check_40mhz in
function hostapd_check_ht_capab. ieee80211n_check_40mhz can return 1 in
a valid scenario where the initialization is completed in a callback. In
this case ieee80211n_supported_ht_capab is skipped and hostapd does not
check the ht capabilities reported by the driver. Fix this issue making
sure ieee80211n_supported_ht_capab gets called.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
If WMM is not disabled explicitly (wmm_enabled=0 in hostapd.conf),
enable WMM automatically whenever HT (ieee80211n) is enabled. Use
the default WMM parameters for AP TX queues and the EDCA parameters
advertised for stations in WMM IE if no overriding values are
included in the configuration.
We can use the P2P interface types to check if the driver supports P2P
and to tell the kernel that a given interface is going to be used for
P2P (when it is created).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no real reason to maintain these in the current development
branch anymore. If someone really needs support for the obsolete
driver interfaces, these can be found in older wpa_supplicant
branches.
driver_atmel.c
- vendor-specific interface for ATMEL AT76C5XXx cards
- for some old out-of-tree driver; not for the upstream atmel*
drivers
driver_ndiswrapper.c
- vendor-specific interface for an out-of-tree driver
- ndiswrapper should work with driver_wext.c, too
driver_ipw.c
- vendor-specific interface for old ipw2100/2200 driver
- the upstream driver works with driver_wext.c (and does not work
with the old interface)
driver_hermes.c
- vendor driver that was not even included in the main wpa_supplicant
releases
In order to enable protection mechanisms for different HT opmodes the
driver needs to be aware of the current HT opmode that is calculated by
hostapd. Hence, pass the current opmode to the nl80211 driver via
the bss attribute NL80211_ATTR_BSS_HT_OPMODE.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
tdls_prohibit=1 and tdls_prohibit_chan_switch=1 and now be used to
disable use of TDLS or TDLS channel switching in the BSS using
extended cabilities IE as defined in IEEE 802.11z.
Make sure that received management frames are long enough before
processing them. This avoids a potential segmentation fault if a
driver delivers an invalid frame all the way to hostapd.
The changes are:
1. the word "and" in the hunting-and-pecking string passed to the KDF
should be capitalized.
2. the primebitlen used in the KDF should be a short not an int.
3. the computation of MK in hostap is based on an older version of the
draft and is not the way it's specified in the RFC.
4. the group being passed into computation of the Commit was not in
network order.
Previously, only the Configuration Error values were indicated in
WPS-FAIL events. Since those values are defined in the specification
it is not feasible to extend them for indicating other errors. Add
a new error indication value that is internal to wpa_supplicant and
hostapd to allow other errors to be indicated.
Use the new mechanism to indicate if negotiation fails because of
WEP or TKIP-only configurations being disallows by WPS 2.0.
This needs to be done both in the more normal location in
p2p_timeout_connect_listen() (internal timeout after driver event) and
in p2p_listen_end() as a workaround for the case where the driver event
is delayed to happen after the internal timeout.
Previously, both NULL and ff:ff:ff:ff:ff:ff addr were used in various
places to indicate default/broadcast keys. Make this more consistent
and useful by defining NULL to mean default key (i.e., used both for
unicast and broadcast) and ff:ff:ff:ff:ff:ff to indicate broadcast
key (i.e., used only with broadcast).
When hostapd is removing a virtual BSS interface, the loop here was
incorrectly not updating the iterator during list traversal and
ended up in an infinite loop in some cases.
Use NULL instead of (u8 *) "" as the seq value and make sure the
driver wrapper implementations can handle NULL value. This was
previously already done in number of places, but not everywhere.
wpa_supplicant seems to crash from time to time on a NetBSD 4.0 MIPS
platform. The root cause turned out to be a MIPS alignment issue.
In my wpa_supplicant crash case, in function
wpa_driver_bsd_event_receive (from driver_bsd.c), the buf[2048] address
is started from i.e. 0x7fffd546, which is not 4 bytes aligned. Later
when it is casted to (struct if_msghdr *), and rtm->rtm_flags is used.
rtm->rtm_flags is "int" type, but its address is not 4 bytes aligned.
This is because the start address of rtm is not 4 bytes aligned.
Unfortunately in NetBSD MIPS kernel (unlike Linux MIPS kernel emulates
unaligned access in its exception handler), the default behavior is to
generate a memory fault to the application that accesses unaligned
memory address. Thus comes the early mentioned wpa_supplicant crash. An
interesting note is when I'm using the wpa_supplicant version 0.4.9, I
never saw this problem. Maybe the stack layout is different. But I
didn't look into details.
I used below patch to resolve this problem. Now it runs correctly for at
least several hours. But you might have a better fix (maybe we can use
malloc/free so that it is at least cache line aligned?). I'm also not
sure if other drivers should have the same problem.
This adds partial callbacks and events to allow P2P management to be
implemented in a driver/firmware. This is not yet complete and is
very much subject to change in the future.
CONFIG_WPS_REG_DISABLE_OPEN=y can be used to configure wpa_supplicant
to disable open networks by default when wps_reg command is used to
learn the current AP settings. When this is enabled, there will be a
WPS-OPEN-NETWORK ctrl_iface event and the user will need to explicitly
enable the network (e.g., with "select_network <id>") to connect to
the open network.
If the underlying driver supports off-channel TX, it will now be used by
the nl80211 driver wrapper, setting WPA_DRIVER_FLAGS_OFFCHANNEL_TX
accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the new kernel functionality coming to Linux to allow off-channel
TX, we can take advantage of that in the P2P code that currently uses
remain-on-channel. If a driver advertises support for it, it will be
asked to handle off-channel TX by itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ClientTimeout changes from EAP peer methods were not supposed to
change behavior for other EAP peer methods or even other sessions
of the same method. Re-initialize ClientTimeout whenever an EAP
peer method is initialized to avoid this. This addresses problems
where WPS (EAP-WSC) reduces the timeout and consecutive EAP runs
may fail due to too small timeout.
If the peer you want to connect to is no longer available (does not
acknowledge frames) when wpa_supplicant sends GO Negotition Request
frames, retransmission of this frame is done until the associated
p2p_device structure is removed on timeout. In that case, no signal
is emitted to inform the GO Negotiation has failed.
When sending an Invitation Request frame, the same retransmission
mechanism is in place but limit the transmission to 100 and hitting
the limit generates an event.
This patch adds the same mechanism as the one in place for Invitation
Request, but with limit of 120 to match the existing wait_count for
for GO Negotiation.
If a station received unprotected Deauthentication or Disassociation
frame with reason code 6 or 7 from the current AP, there may be a
mismatch in association state between the AP and STA. Verify whether
this is the case by using SA Query procedure. If not response is
received from the AP, deauthenticate.
This implementation is only for user space SME with
driver_nl80211.c.
Some new code will require access to P2P group members, so add API to
retrieve the number of members and iterate the members themselves.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there is a pending GO Negotiation when p2p_cancel is used,
unauthorize the peer to avoid immediate reconnection from being
accepted without a new p2p_connect command.
This can be used by external programs (e.g., wlantest_cli) to inject
raw frames (hex dump of the frame header and body). The data can be
requested to be sent as-is or protected with the current key.
Previously, pairwise and group cipher suites were configured only
when kernel SME (nl80211 connect API) was used. However, mac80211
needs this information even in the user space SME case for one
thing: to disable HT when TKIP/WEP is used. Add
NL80211_ATTR_CIPHER_SUITES_PAIRWISE to fix this special case with
user space SME. This allows mac80211 to disable HT properly when
the AP is configured with configuration that is not allowed.
This add preliminary code for setting the per-STA RX GTK for
RSN IBSS when nl80211 drivers. For some reason, this does not
seem to fully work, but at least driver_nl80211.c is now aware of
what kind of key is being set and the whatever is missing from
making this key configuration go through should be specific to
nl80211/cfg80211.
The frame needs to be sent from an individual (non-group) address,
so drop invalid frames before sending Deauth/Disassoc frames to
not associated STAs.
One of the pointers to the PAC buffer was not updated after realloc
and if the realloc ended up returning new pointer, the *pos pointer
was still pointing at the old location (i.e., freed memory at
this point).
When controlling multiple virtual interfaces on the same physical
radio, share the scan results events with sibling interfaces. This
decreases the time it takes to connect many virtual interfaces.
This is currently only supported on Linux with cfg80211-based
drivers when using nl80211 or wext driver interface.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Some drivers are not providing exactly reliable error codes (e.g.,
with WEXT), but others may actually indicate reliable information.
Allow driver wrappers to indicate if that is the case and use
optimizations if so. For now, this improves nl80211 with
NL80211_CMD_CONNECT for a case where connection request fails.
driver_param=use_p2p_group_interface=1 can now be used to test
nl80211-drivers with separate P2P group interface. In other words,
the main interface (e.g., wlan0) is reserved for P2P management
operations and non-P2P connections and a new group interface (e.g.,
p2p-wlan0-0) is created for the P2P group.
This implementation is very minimal, i.e., it only support address
allocation for a single P2P group interface (if the driver does not
handle this internally). In addition, not all functionality has yet
been tested, so for now, this is disabled by default and needs that
special driver_param to enable.
WPA_DRIVER_FLAGS_P2P_MGMT_AND_NON_P2P flag can now be used to
indicate that the initial interface (e.g., wlan0) is used for
P2P management operations and potentially non-P2P connections.
This is otherwise identical to
WPA_DRIVER_FLAGS_P2P_DEDICATED_INTERFACE, but the possibility of
non-P2P connections makes some operations differ.
Getting rid of these inline functions seems to reduce the code size
quite a bit, so convert the most commonly used hostapd driver ops to
function calls.
This is not needed anymore and just makes things more difficult
to understand, so move the remaining function pointers to direct
function calls and get rid of the struct hostapd_driver_ops.
send_eapol, set_key, read_sta_data, sta_clear_stats,
set_radius_acl_auth, set_radius_acl_expire, and set_beacon
to use inline functions instead of extra abstraction.
Commit bf65bc638f started the path to
add this new abstraction for driver operations in AP mode to allow
wpa_supplicant to control AP mode operations. At that point, the
extra abstraction was needed, but it is not needed anymore since
hostapd and wpa_supplicant share the same struct wpa_driver_ops.
Start removing the unneeded abstraction by converting
send_mgmt_frame() to an inline function, hostapd_drv_send_mlme().
This is similar to the design that is used in wpa_supplicant and
that was used in hostapd in the past (hostapd_send_mgmt_frame()
inline function).
driver.h defines these functions to return 0 on success, not
number of bytes transmitted. Most callers are checking "< 0" for
error condition, but not all. Address this by following the driver
API specification on 0 meaning success.
On Linux, verify that the kernel entropy pool is capable of providing
strong random data before allowing WPA/WPA2 connection to be
established. If 20 bytes of data cannot be read from /dev/random,
force first two 4-way handshakes to fail while collecting entropy
into the internal pool in hostapd. After that, give up on /dev/random
and allow the AP to function based on the combination of /dev/urandom
and whatever data has been collected into the internal entropy pool.
wlan0: RADIUS No authentication server configured
MEMLEAK[0x999feb8]: len 1040
WPA_TRACE: memleak - START
[3]: ./hostapd(radius_msg_new+0x33) [0x8074f43]
radius_msg_new() ../src/radius/radius.c:117
[4]: ./hostapd() [0x806095e]
ieee802_1x_encapsulate_radius() ../src/ap/ieee802_1x.c:439
ieee802_1x_aaa_send() ../src/ap/ieee802_1x.c:1496
For example, this error occured when I used WPS hostapd without
"eap_server=1" definition in configuration file.
By default, make hostapd and wpa_supplicant maintain an internal
entropy pool that is fed with following information:
hostapd:
- Probe Request frames (timing, RSSI)
- Association events (timing)
- SNonce from Supplicants
wpa_supplicant:
- Scan results (timing, signal/noise)
- Association events (timing)
The internal pool is used to augment the random numbers generated
with the OS mechanism (os_get_random()). While the internal
implementation is not expected to be very strong due to limited
amount of generic (non-platform specific) information to feed the
pool, this may strengthen key derivation on some devices that are
not configured to provide strong random numbers through
os_get_random() (e.g., /dev/urandom on Linux/BSD).
This new mechanism is not supposed to replace proper OS provided
random number generation mechanism. The OS mechanism needs to be
initialized properly (e.g., hw random number generator,
maintaining entropy pool over reboots, etc.) for any of the
security assumptions to hold.
If the os_get_random() is known to provide strong ramdom data (e.g., on
Linux/BSD, the board in question is known to have reliable source of
random data from /dev/urandom), the internal hostapd random pool can be
disabled. This will save some in binary size and CPU use. However, this
should only be considered for builds that are known to be used on
devices that meet the requirements described above. The internal pool
is disabled by adding CONFIG_NO_RANDOM_POOL=y to the .config file.
This commit adds a new wrapper, random_get_bytes(), that is currently
defined to use os_get_random() as is. The places using
random_get_bytes() depend on the returned value being strong random
number, i.e., something that is infeasible for external device to
figure out. These values are used either directly as a key or as
nonces/challenges that are used as input for key derivation or
authentication.
The remaining direct uses of os_get_random() do not need as strong
random numbers to function correctly.
This adds more time for the system entropy pool to be filled before
requesting random data for generating the WPA/WPA2 encryption keys.
This can be helpful especially on embedded devices that do not have
hardware random number generator and may lack good sources of
randomness especially early in the bootup sequence when hostapd is
likely to be started.
GMK and Key Counter are still initialized once in the beginning to
match the RSN Authenticator state machine behavior and to make sure
that the driver does not transmit broadcast frames unencrypted.
However, both GMK (and GTK derived from it) and Key Counter will be
re-initialized when the first station connects and is about to
enter 4-way handshake.
The example GMK-to-GTK derivation described in the IEEE 802.11 standard
is marked informative and there is no protocol reason for following it
since this derivation is done only on the AP/Authenticator and does not
need to match with the Supplicant. Mix in more data into the derivation
process to get more separation from GMK.
The previous commit broke completion in various places. The proper
way of handling the completion of full word is to verify whether
there are more than one possible match at that point.
Completion needs to be done even if the full word has been entered.
In addition, fix the space-after-full-word to properly allocate room
for the extra character when completion is used in the middle of the
string.
This adds new commands for wlantest_cli to request wlantest to
inject frames. This version can only send out Authentication
frames and unprotected SA Query Request frames, but there is
now place to add more frames and encryption with future commits.
ap_setup_locked=2 can now be used to enable a special mode where
WPS ER can learn the current AP settings, but cannot change then.
In other words, the protocol is allowed to continue past M2, but
is stopped at M7 when AP is in this mode. WPS IE does not
advertise AP Setup Locked in this case to avoid interoperability
issues.
In wpa_supplicant, use ap_setup_locked=2 by default. Since the AP PIN
is disabled by default, this does not enable any new functionality
automatically. To allow the read-only ER to go through the protocol,
wps_ap_pin command needs to be used to enable the AP PIN.
There is no point in maintaining two almost identical versions
of this parser. Move WPA IE parser into wpa_common.c similarly
to what was already the case with RSN IE parse.
When multiple wireless interfaces are used with WPS, the UPnP
subscriptions need to be removed whenever a matching Registrar
instance gets removed. This avoids a segfault due to access to
freed memory during hostapd shutdown.
In addition, the UPnP interface instance structure needs to be
freed to avoid memory leak.
WPS external Registrars can get confused about multiple UPnP
instances (one per radio) on a dual-concurrent APs. Simplify the
design by sharing a single UPnP state machine for all wireless
interfaces controlled by hostapd. This matches with the previous
changes that made a single command enable WPS functionality on
all interfaces.
This is relatively minimal change to address the sharing of the
state among multiple struct hostapd_data instances. More cleanup
can be done separately to remove unnecessary copies of information.
When the peer does not include our initial preference in the Channel
List attribute during GO Negotiation, try to use the best channel of
the other band as the new preference instead of falling back to the
first channel in the intersection.
The driver wrapper may now indicate the preferred channel (e.g., based
on scan results) on both 2.4 GHz and 5 GHz bands (and an overall best
frequency). When setting up a GO, this preference information is used
to select the operating channel if configuration does not include
hardcoded channel. Similarly, this information can be used during
GO Negotiation to indicate preference for a specific channel based
on current channel conditions.
p2p_group_add command can now use special values (freq=2 and freq=5)
to indicate that the GO is to be started on the specified band.
Commit d8d940b746 introduced a regression
that prevented TSN APs from being used with WEP since the AP was
rejected if it advertised WPA or RSN IE when we were configured to use
WEP. Resolve this by checking whether the AP is advertising a TSN, i.e.,
whether the AP allows WEP to be used as a group cipher. If so, allow
the AP to be selected if we are configured to use static WEP or
IEEE 802.1X (non-WPA).
It should be noted that this is still somewhat more restricted in AP
selection than earlier wpa_supplicant branches (0.7.x or older) that
ignore the WPA/RSN IE completely when configured for non-WPA.
This tool can be used to capture IEEE 802.11 frames either from a
monitor interface for realtime capturing or from pcap files for
offline analysis. This version is only adding basic infrastructure for
going through the frames and parsing their headers.
Commit c3fc47ea8e fixed EAP passthrough
server to allow Logoff/Re-authentication to be used. However, it
broke EAP standalone server while doing that. Fix this by reverting
the earlier fix and by clearing the EAP Identity information in the
EAP server code whenever an EAPOL-Start or EAPOL-Logoff packet is
received.
We need to drop the pending frame to avoid issues with the new GO
Negotiation, e.g., when the pending frame was from a previous attempt at
starting a GO Negotiation.
These are not used by any driver wrapper, i.e., only the four
data queues (BK, BE, VI, VO) are configurable. Better remove these
so that there is no confusion about being able to configure
something additional.
Pass data frames from unknown STAs to hostapd in order to reply with
a Deauthentication or Disassociation frame. This fixes compliance
with IEEE Std 802.11-2007, 11.3.
Furthermore, this does not cause a lot of overhead (at least with
mac80211 drivers) since mac80211 does not pass all data frames (but
at least from unauthenticated and unassociated STAs) to cooked monitor
interfaces.
Tested with rt2800pci on a MIPS board.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
drivers.mak is shared between hostapd and wpa_supplicant and
compiling them together may create "wrong" flags.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
We are not actually interested in the PD Response in join-a-group
case, so there is no point in trying to send PD Request until the
response is received. This avoids an extra PD getting started after
a join-a-group operation in some cases.
This is needed to avoid problems with other applications setting and
leaving the interface to IF_OPER_DORMANT state. In AP mode, the interface
is ready immediately after the keys are set, so we better make sure the
DORMANT state does not prevent normal operations after that.
This is needed to avoid issues with APs that restart their UPnP,
e.g., when ER reconfigures them. The previously known settings are
now cached and taken into use if an AP is detected to leave
(ssdp:byebye) and then return.
Verify that the UUID given to wps_er_pbc command is known and only
activate PBC mode on the matching AP. The UUID can be that of the
AP or the station/Enrollee.
Add a new driver event, EVENT_INTERFACE_UNAVAILABLE, for indicating
that the driver is not able to continue operating the virtual
interface in its current mode anymore, e.g., due to operating
channel for GO interface forced to a DFS channel by another virtual
interface.
When this happens for a P2P group interface, the P2P group will
be terminated and P2P-GROUP-REMOVED event shows the reason for
this as follows:
P2P-GROUP-REMOVED wlan0 GO reason=UNAVAILABLE
A new configuration parameter, p2p_group_idle, can now be used to set
idle timeout value for P2P groups in seconds (0 = no timeout). If set,
this values is used to remove P2P group (both GO and P2P client)
interfaces after the group has been idle (no clients/GO seen) for the
configuration duration.
The P2P-GROUP-REMOVED event is now indicating the reason for group
removal when known. For example:
P2P-GROUP-REMOVED wlan0 GO reason=REQUESTED
P2P-GROUP-REMOVED wlan1 client reason=IDLE
Some driver wrappers may end up indicating a disassociation or
deauthentication event without the address of the station, e.g.,
based on a previous non-AP mode event. Avoid crashing hostapd
by verifying that the require address parameter is available in
the event before processing it.
In order to avoid confusing the driver with a new remain-on-channel
request, delay sending of a new Action frame if the driver indicates
Action frame RX diromg a scan.
This is needed to optimize response to GO Negotiation Request frames.
The extra remain-on-channel cancel followed by new remain-on-channel for
the same channel takes too much time with some driver/firmware
designs for the response to go out quickly enough to avoid peer
timing out while waiting for our response.
This command can be used to enroll a network based on a local
network configuration block instead of having to (re-)learn the
current AP settings with wps_er_learn.
This test command is supposed to change the WPS version number in all
places immediately, so make sure that the IEs used in management
frames get updated immediately.
The P2P group component is now tracking of associated stations
in the group and the Group Limit bit in the Group Capabilities
is updated based on whether there is room for new clients in
the group.
The workaround to ignore no ctrl::ack received for GO Negotiation
Confirmation frame was only supposed to be used when the frame was
actually transmitted and just the ack was not received. However, due
to the way the driver failure on transmitting the frame were reported,
this ended up getting applied for all failures in sending the GO
Negotiation Confirmation frame.
Improve this by providing a mechanism to indicate whether send_action
operations fail locally before the frame was actually transmitted or
because of not receiving ack frame after having transmitted the frame.
UPnP event subscriptions are not supposed to be dropped based on
whether events can be delivered quickly enough. Leave dropping to
happen only based on failed deliveries to avoid issues with a burst
of events kicking out still active subscribers.
Do not send more than five Probe Request WLANEvent notifications
per second. Even though the limit should in theory apply to all
WLANEvents, it is better not to drop EAP notifications because
of Probe Request frames and really, the only real reason for
event bursts is Probe Request frames.
Instead of queuing all events for a subscriber, only queue more
important events if delivery of event notifications starts failing.
This allows more time for the subscriber to recover since the maximum
queue length if not reached because of Probe Request frames only.
Instead of dropping the subscription on first failure, allow up to
10 failures before dropping. In addition, drop the callback URLs
one by one instead of full subscription if only one URL is failing.
If CONFIG_DRIVER_WEXT=y is not used in .config, but driver_wext.c
gets pull in to help another driver wrapper, rfkill code needs to
included to fix the build.
Listen to regulatory event messages from kernel and convert them to
internal driver event notifications indicated that the channel list
may have changed.
The AP operation with wpa_supplicant requires an additional callback
to get the needed event information from hostapd side so that
wpa_msg() can be called for wpa_s->parent if needed.
This makes it easier to figure out what could have failed in the
WPS protocol and potentially provide more information for the
user on how to resolve the issue.
The driver wrapper can now indicate whether the driver supports
concurrent operations on multiple channels (e.g., infra STA connection
on 5 GHz channel 36 and P2P group on 2.4 GHz channel 1). If not,
P2P_CONNECT commands will be rejected if they would require
multi-channel concurrency.
The new failure codes for P2P_CONNECT:
FAIL-CHANNEL-UNAVAILABLE:
The requested/needed channel is not currently available (i.e., user has
an option of disconnecting another interface to make the channel
available).
FAIL-CHANNEL-UNSUPPORTED:
The request channel is not available for P2P.
At least D-Link DIR-600 and DIR-825 have been reported to include
an extra octet after the Network Key attribute within a Credential
attribute. This can happen at least when they are provisioning an
open network.
Add a workaround to detect this incorrectly encoded attribute and
to skip the extra octet when parsing such a Credential.
The new nl80211 API means we don't need to use monitor interfaces. This
means that the P2P implementation now requires a kernel that has support
for generic management frame (not just Action frame) transmission.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is backward compatible since older kernels will ignore the extra
attribute and only allow registration for Action frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
libnl has a bug, when binding more than two sockets and releasing one,
it will release the wrong address and then try to reuse it, which fails.
Therefore, we need to reimplement the socket address assignment logic
locally for libnl 1.1.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some sequencies of EAPOL logoff/logon/start messages seem to be
able to get the previous implementation into state where hostapd
would not be able to start reauthentication when external
authentication server is used. The EAP server code would bypass
the initial Identity Request generation and EAPOL code would not
be able to send anything to the authentication server or supplicant
at that point. Work around this by forcing EAP server code to
start with Identity Request after INITIALIZE state even if the
Identity is known.
When a single hostapd process is controlling multiple interfaces,
apply the received or auto-generated configuration changes to all
interfaces that have enabled WPS.
When the same hostapd process is controlling multiple interfaces,
apply WPS commands (push button, add PIN, change AP PIN) to all
interfaces that are configured to use WPS.
A separate build number (etc.) version number postfix can now be
added to the build without having to modify source code files by
defining VERSION_STR_POSTFIX. This can be done, e.g., by adding
following line to .config:
CFLAGS += -DVERSION_STR_POSTFIX=\"-foo\"
Commit 3379a3a795 added a direct
iface->for_each_interface use without verification whether the
function is available. This works with hostapd, but not
wpa_supplicant (which crashes on segfault).
The previous implementation ended up incorrectly assuming that all
40 MHz use cases have secondary channel above the primary one. Fix this
by properly masking the secondary channel offset field and checking its
value.
wpa_supplicant showed signal levels incorrectly with some drivers:
Jun 6 16:29:36 rupert wpa_supplicant[18945]: Current BSS: 00:0d:97:11:40:d6
level=190
Jun 6 16:29:36 rupert wpa_supplicant[18945]: Selected BSS: 00:0d:97:11:50:09
level=192
Judging from output from other tools (iwlist) and the min_diff block
at the end of wpa_supplicant_need_to_roam, it seems these values
should actually be negative. Specifically, if one treats that number
as a signed char instead of unsigned, everything matches up.
To be honest, I've little to no understanding of wireless, but looking
at the source code for wireless-tools (iw_print_stats in iwlib.c), it
seems that the fields of the iw_quality struct need to be decoded
differently depending on various flags. I guess
src/drivers/driver_wext.c should have similar logic in
wext_get_scan_qual.
I wrote a patch that attempts to replicate some of that logic,
although it may be more complicated than is necessary; I think some of
the complexity is for backwards-compatibility, which might not be
necessary depending on wpa_supplicant's dependencies? In any case, it
is attached. Again, I don't know how any of this works, so it's likely
the patch is a bit off. But I think at least the logic to determine
min_diff in wpa_supplicant_need_to_roam would be more accurate if
level were determined correctly.
We need to clear the selected registrar timeout from wps_er_learn
when stopping the protocol run at M7 (previously, this was done only
when WSC_Done was being processed). In addition, we need to cancel
the timeout when a new PBC operation is started.
This is needed to update the pointers maintained within WPS code
to use the new configuration data instead of maintaining pointers
to the old configuration which will be freed. This fixes strings in
UPnP discovery after reconfig (they used to be random freed memory..).
Need to figure out whether the message is from a WSC 2.0 -based
device based on the unencrypted attributes, not the contents of the
encrypted data since the Version2 subelement is only included in the
unencrypted area.
This seems to be the easiest way of making sure the Config Methods
value is compliant with the WSC 2.0 specification without having
to modify the configuration file. However, this will only add the
virtual flag, so the configuration files should really be updated
to specify values that match the AP design.
WPS 2.0 mandates the AP to include WPS IE in (Re)Association Response
if the matching (Re)Association Request included WPS IE. Provide the
needed WPS IE information to the driver_ops API for drivers that
process association frames internally.
Note: This modifies the driver_ops API by adding a new argument to
set_ap_wps_ie().
Instead of build time options (CONFIG_WPS_TESTING_EXTRA_CRED and
CONFIG_WPS_EXTENSIBILITY_TESTING), use a single build option
(CONFIG_WPS_TESTING) and runtime configuration of which testing
operations are enabled. This allows a single binary to be used
for various tests.
The runtime configuration can be done through control interface
with wpa_cli/hostapd_cli commands:
Enable extensibility tests:
set wps_version_number 0x57
Disable extensibility tests (WPS2 build):
set wps_version_number 0x20
Enable extra credential tests:
set wps_testing_dummy_cred 1
Disable extra credential tests:
set wps_testing_dummy_cred 0
If the peer is not authorized for GO Negotiation, wps_method is not
actually set. In that case, it is better to fill in our default
config methods rather than end up leaving the field to be zero.
The Beacon frame must include UUID-E and RF Bands attributes when
in active PBC mode to allow stations to figure out that two BSSes in
PBC mode is not a PBC session overlap.
When generating the UUID based on MAC address, share the same UUID
with all interfaces. This fixes a potential issue with concurrent
dualband APs where the UUID needs to be same for PBC to work properly.
If the msg->device_name buffer is filled from two different sources,
the copy from the P2P Device Info attribute needs to make sure that
the values gets null terminated to match the length of the correct
string should the other place use another string (which is not really
allowed by the spec, but could happen).
A new ctrl_interface command, WPS_CANCEL, can now be used to cancel
a pending or ongoing WPS operation. For now, this is only available
with wpa_supplicant (either in station or AP mode). Similar
functionality should be added for hostapd, too.
If an authorized (p2p_connect used locally) GO Negotiation is
rejected when receiving GO Negotiation Request from the peer,
indicate the failure with a ctrl_interface P2P-GO-NEG-FAILURE
event. Previously, this event was only shown on the peer (i.e.,
the device receiving the GO Negotiation Response with non-zero
Status code).
Since this message now includes P2P Device Info attribute, it is
reasonable to learn the peer data and process the message instead of
rejecting the message.
Add (or complete Probe Request only) P2P peer entry when receiving
Provision Discovery Request from a previously unknown peer. This is
especially of use for a GO when a P2P client is requesting to join
a running group.
The scan operation before Provision Discovery Request may not include
the GO. However, we are likely to have the GO in our P2P peer table,
so use that information to figure out the operating channel if BSS
table entry is not available.
This should not really happen, but it looks like the Listen command
may fail is something else (e.g., a scan) was running at an
inconvenient time. As a workaround, allow new Extended Listen
operation to be started if this state is detected.
The previous version had a bug that could result in NULL pointer
dereference if the P2P IE included Manageability attribute, but no
Capability attribute.
This can happen, e.g., when a P2P client connects to a P2P group
using the infrastructure WLAN interface instead of P2P group
interface. In that case, the P2P client may behave as if the GO
would be a P2P Manager WLAN AP.
This is needed to be able to change parameters for dynamically
created interfaces between the creation of the interface and
association/start AP commands.
Following ctrl_interface commands can now be used:
P2P_SET client_apsd disable
- disable configuration (i.e., use driver default) in client mode
P2P_SET client_apsd <BE>,<BK>,<VI>,<VO>;<max SP Length>
- enable UASPD with specific trigger configuration (0/1) per AC
(max SP Length is currently ignored)
P2P_SET go_apsd disable
- disable configuration (i.e., use driver default) in AP mode
P2P_SET go_apsd <0/1>
- disable/enable APSD in AP mode
P2P specification v1.15 fixed the description of the GAS fragmentation
to not duplicate NQP Query Response Field header in all fragments. This
change makes the fragmentation match with the description in IEEE
802.11u. The change is not backwards compatible with previous P2P
specification versions as far as fragmented SD responses are concerned.
This event indicates the Device Password ID that the peer tried
to use in GO Negotiation. For example:
P2P-GO-NEG-REQUEST 02:40:61:c2:f3:b7 dev_passwd_id=4
If enabled, cross connection allows GO to forward IPv4 packets
using masquerading NAT from the P2P clients in the group to an
uplink WLAN connection. This is disabled by default and can be
enabled with "wpa_cli p2p_set cross_connect 1" on the P2P device
interface.
When we receive Device Discoverability Response, we need to initiate
new GO Negotiation as quickly as possible to avoid the target client
from going back to sleep. Make sure we do not end up in
P2P_CONNECT_LISTEN state (short Listen mode) in this case.
For now, this applies to the test command that can be used to set
periodic NoA (p2p_set noa). The value are stored and periodic NoA
is enabled whenever there are no non-P2P STAs connected to the GO.
While this is not strictly speaking required by the P2P specification
for a not-P2P Managed Device, this can provide useful information for
the P2P manager AP and may be needed to pass certification tests.
While there is no real value in this, the spec seems to mark this
attribute as mandatory from GO, so better included it regardless
of whether we have clients or not (the attribute is empty in case
no clients are connected).
"wpa_cli p2p_set peer_filter <MAC address>" can now be used to
only allow a single P2P Device (based on P2P Device Address) to be
discovered for testing. Setting the address to 00:00:00:00:00:00
disables the filter.
The WSC 2.0 specification moved to use another design for the new
attributes to avoid backwards compatibility issues with some
deployed implementations.
If CONFIG_WPS_STRICT is set, validate WPS IE(s) in management frames and
reject the frames if any of the mandatory attributes is missing or if an
included attribute uses an invalid value. In addition, verify that all
mandatory attributes are included and have valid values in the WSC
messages.
If all the device information attributes use their maximum lengths,
a single WPS IE is not enough to fit in all the data and as such,
we must be able to fragment the data. In addition, the wpabuf needs
to be allocated larger to fit in maximum data.
Instead of using 0x00 as the extra character, use space (' ') to
avoid failing tests that verify that the variable length string
attributes are not null terminated. In addition, this workaround
can now be disabled by defining CONFIG_WPS_STRICT for the build.
This can be done by adding following line to .config:
CFLAGS += -DCONFIG_WPS_STRICT
However, it should be noted that such a build may not interoperate
with some deployed WPS 1.0 -based implementations and as such, is
mainly designed for testing.
Whenever wpa_supplication is using Request Type Enrollee, it is trying
to enroll into a network. Indicate this with the explicit inclusion of
Request to Enroll attribute with value TRUE.
Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
This adds definitions and parsing of the new attributes that were added
in WPS 2.0. In addition, the version negotiation is updated to use the
new mechanism, i.e., accept everything received and use the new Version2
attribute in transmitted messages.
While this is not strictly speaking required based on dynamic
configuration (i.e., dot11ShortPreambleOptionImplemented is static
value based on implementation, not runtime configuration), it is better
to follow local configuration parameter for short preamble in addition
to the associated station capabilities.
This function is not really needed in case of drivers that build the
HT IEs internally. However, since this can get called if ieee80211n=1
is set in hostapd.conf, we better not segfault even if the driver
does not provide hw info (hapd->iface->current_mode == NULL).
Commit 5a1cc30f1a added code that was
assuming CONFIG_WPS_UPNP is enabled whenever CONFIG_WPS is. Fix this
by making the UPnP calls conditional on CONFIG_WPS_UPNP define.
Prior to commit 6195adda9b the sm->user
dereference did not exist here. While this is in practice non-NULL,
better use more defensive construction here to avoid NULL pointer
dereference should this ever change.
Some NDIS drivers require a workaround to allow them to associate
with a WPS AP that is already using protection (Privacy field = 1).
Let driver_ndis.c know if the AP is already using Privacy and if so,
configure a dummy WEP key to force the driver to associate.
When using overlapped write, we must have the provided memory
areas available during the operation and cannot just use stack
unless we wait for the completion within the function. In the case
of TX here, we can easily wait for the completion since it is likely
to happen immediately. In addition, this provides more reliable
success/failure return value for l2_packet_send(). [Bug 328]
hostapd simply used its own STBC configuration in the STA's HT caps. This
resulted in TX STBC being used for STAs not supporting RX STBC, which in
turn resulted in the STA not receiving anything.
Fix this by handling the STBC flags in the same way mac80211 does. Mask
out RX STBC if we don't support TX STBC and vice versa.
Tested only with the nl80211 driver and a STBC incapable STA.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
This patch adds support for wired IEEE 802.1X client on the Solaris.
I have tested with these:
OS : OpenSolaris 2009.06
EAP : EAP-MD5
Switch : Cisco Catalyst 2950
The arithmetic on void pointer exists in trace routine. On GNU C, it
works because void pointer size is 1, but not all compilers behave like
this. So this patch specifies the size of the pointer.
There is no need to process the public key and generate keys if
the AP is going to reject this M2 anyway. This limits effect of
potential CPU DoS attacks in cases where AP PIN is disabled.
A new hostapd_cli command, wps_ap_pin, can now be used to manage
AP PIN at runtime. This can be used to generate a random AP PIN and
to only enable the AP PIN for short period (e.g., based on user
action on the AP device). Use of random AP PIN that is only enabled
for short duration is highly recommended to avoid security issues
with a static AP PIN.
As a compromise between usability and security, do not disable
AP PIN permanently based on failed PIN validations. Instead, go to
AP Setup Locked state for increasing amount of time between each
failure to slow down brute force attacks against the AP PIN.
This avoids problems with some external Registrars that may try
to use the same PIN multiple times without user input. Now, the
user will still be able to fix the PIN and try again later while
a real attack is delayed enough to make it impractical.
This can happen on the AP if the AP PIN is not configured and
the client tries to go through the protocol instead of just using
Registrar mode to receive M1 from the AP. It is cleaner to send
out the WSC_NACK instead of just stopping the protocol.
This indicates that the peer identity is associated with the
credential and will be required to match with the identity used
during authentication when the PAC is used (RFC 5422, 4.2.4).
When passing several authentication algorithms through auth_alg, we
should try all of them when the first one fails. The wext driver goes
through the connect nl80211 command and the retries are then handled by
the kernel. The nl80211 doesn't and we have to handle that from
userspace.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
DEAUTH messages can come from a number of different sources. The one
that's hurting us currently is DEAUTH netlink messages coming to us
from compat-wireless in response to local_state_change DEAUTH messages
we sent as a part of cleaning up state in driver_nl80211's
clear_state_mismatch() function. However, DEAUTH messages can come
from a variety of unwanted sources, including directed denial-of-service
attacks (although MAC verification doesn't place that high a barrier),
so this validation is actually generically useful, I think.
The downside to this method is that without a kernel based approach
"iw dev wlan0 link" no longer works correctly after clear_state_mismatch()
is done. This will be pursued with the kernel folks.
cfg80211/mac80211 seems to be unwilling to change interface mode in
some cases. Make these less likely to cause problems by trying the
changes up to 10 times with 100 msec intervals.
In theory, this should not really be needed, but Windows 7 uses
Registrar mode to probe AP's WPS capabilities before trying to use
Enrollee and fails if the AP does not allow that probing to happen.
This allows the AP to start as an Enrollee and send M1, but refuse
to continue beyond that (M3 will not be sent if AP PIN is not known).
This makes it easier (and a bit faster) to handle multiple local
radios with FT. There is no need to depend on l2_packet in that
case since the frame can be delivered as a direct function call.
If the station does not include WSC IE in Association Request, it
is marked with WLAN_STA_MAYBE_WPS flag. We can update that to
WLAN_STA_WPS if the station uses either of the WPS identity strings.
This enables some workarounds for WPS stations.
This works around issues with EAP-Failure getting lost for some reason.
Instead of waiting up to 60 seconds on a timeout, 30 second timeout is
now used and whenever the provisioning step has been completed (either
successfully or unsuccessfully), this timeout is reduced to 2 seconds.
The pairwise cipher field is supposed to be little endian, but the
message building functions did not swap the bytes on big endian
hosts while the message processing functions did. Fix this by using
little endian byte order in both places.
It looks like 10.6.3 and 10.6.4 do not like to receive Network Key
with WPA passphrase while PSK format still works. Use peer information
from M1 to figure out whether the Enrollee is likely to be OS X and
if so, force PSK format to be used for Network Key.
Some frequent debug prints are of limited use and make debug output
difficult to read. Make them use a new debug level so that -dd
provides more readable output (-ddd can now be used to enable
the excessive debug prints).
The length of the prime was used incorrectly and this resulted
in WPS DH operation failing whenever the public key ended up having
leading zeros (i.e., about every 1/256th time).
The AP configuration may change after provisioning, so it is better
not to use the current security policy to prioritize results. Instead,
use WPS Selected Registrar attribute as the main sorting key and use
signal strength next without considering security policy or rate sets.
The non-WPS provisioning case remains as-is, i.e., this change applies
only when trying to find an AP for WPS provisioning.
Some deployed implementations do not include the mandatory Network
Key attribute when a WPS Credential is for an open network. Allow
this to improve interoperability since the actual key value is not
really needed for open networks.
Replace use of rfkill block event with rtnetlink ifdown. This makes
the design more robust since the rfkill event could have been for
another interface while the rtnetlink events are already filtered
based of ifindex. In addition, the new design handles other than
rfkill-triggered ifdown/ifup events, too. rfkill unblocked event
is still needed to try to set the interface back up. If the unblock
was for another interface, ifup will fail and the driver state is
not changed.
Some of the driver wrappers need to get set_ieee8021x() call before
they can configure keys. Reorder the operations in the reloading
of configuration case to match with that expectation.
Setting IEEE80211_PARAM_AUTHMODE to IEEE80211_AUTH_AUTO ends up enabling
Privacy mode in the driver. We need to clear that to allow hostapd to be
reconfigured into open mode.
wps_er_config can now be used to configure an AP. It is similar to
wps_er_learn, but instead of only learning the current AP settings,
it continues to send M8 with the new settings for the AP.
wps_er_start command now takes an optional parameter that can be used
to configure a filter to only allow UPnP SSDP messages from the
specified IP address. In practice, this limits the WPS ER operations
to a single AP and filters out all other devices in the network.
When starting the protocol run with an Enrollee, clone the AP Settings
and replace the AP MAC Address with the Enrollee MAC Address so that the
correct value is then used in the Credential attribute in M8.
If the associating station indicates that it is intents to use WPS
by including WPS IE in (Re)Association Request frame, include WPS IE
in (Re)Association Response frame.
There may be more than one attribute of same type (e.g., multiple DC
attributes), so the code needs to be able to handle that. Replace the
fixed structure with an array of attributes.
Previous version driver_bsd.c switches the channel in
wpa_driver_bsd_associate(). This patch changes it to use set_freq().
I have tested this patch on FreeBSD 8.0/NetBSD 5.0.2 with hostapd,
wpa_supplicant(AP) and wpa_supplicant(STA).
Add a new wpa_supplicant state: interface disabled. This can be used
to allow wpa_supplicant to be running with the network interface even
when the driver does not actually allow any radio operations (e.g.,
due to rfkill).
Allow driver_nl80211.c and driver_wext.c to start while rfkill is in
blocked state (i.e., when ifconfig up fails) and process rfkill
events to block/unblock WLAN.
Vendor-specific IEs are supposed to be in the end of the frame, so move
WMM into the end of Beacon, Probe Response, and (Re)Association Response
frames. In addition, move HT IEs to be later in (Re)Association
Response to match the correct order.
hostapd_eid_wpa() adds multiple IEs and the end result may not always be
correct. If WPA is enabled, WPA IE (vendor-specific) gets added in the
middle of the frame and not in the end. This would require a larger
change to spliut the IEs from WPA module into separate locations when
constructing Beacon and Probe Response frames. This is not yet addressed.
Commit 83935317a7 added forced
disconnection in case of 4-way handshake failures. However, it should
not have changed the case where the supplicant is requesting fallback
to full EAP authentication if the PMKID in EAPOL-Key message 1/4 is
not know. This case needs to send an EAPOL-Start frame instead of
EAPOL-Key message 2/4.
This works around a problem with APs that try to force PMKSA caching
even when the client does not include PMKID in (re)association request
frame to request it. [Bug 355]
Commit c02d52b405 removed direct calls
to the WPA authenticator, but the change here was incorrect.
EAPOL_SM_USES_WPA was supposed to be set based on sta->wpa_sm being
set, i.e., no need to check for PMKSA entries for that.
While this could potentially change EAPOL Key TX state machine behavior,
no clear problems have been identified so far. Anyway, better fix this
to get the correct flags set for EAPOL authenticator state machine.
When using WPS, we may end up here if the STA manages to re-associate
without the previous STA entry getting removed. Consequently, we need to
make sure that the WPA state machines gets initialized properly at this
point.
62477841a1 tried to address fragmentation
issues, but it did not address the case where the final EAP-TNC
message gets fragmented. Move the state update to the correct place
to address this case, too.
There are no subdirectories in any of these directories or plans
for adding ones. As such, there is no point in running the loop
that does not do anything and can cause problems with some shells.
Both the wildcard VLAN entry and the statically configured VLAN
interfaces should behave in the same way. Initializing the
full dynamic VLAN code before adding the statically configured VLAN
interfaces allows the same processing to be applied to both statically
and dynamically added VLAN interface (i.e., also the statically
configured ones will be added to a bridge).
The WPS IE was overriding the WPA/RSN IE in driver based MLME case
(hostapd_notif_assoc), but the MLME code here was not using WPS IE
correctly, i.e., it allowed the WPA/RSN IE override the operation.
The returned buffer length was hardcoded to be the prime length
which resulted in shorter results being padded in the end. However,
the results from DH code are supposed to be unpadded (and when used
with WPS, the padding is done in WPS code and it is added to the
beginning of the buffer). This fixes WPS key derivation errors
in about 1/256 of runs ("WPS: Incorrect Authenticator") when using
the internal crypto code.
This adds more details into the CTRL-EVENT-DISCONNECTED event to
make it easier to figure out which network was disconnected in some
race conditions and to what could have been the reason for
disconnection. The reason code is currently only available with
the nl80211 driver wrapper.
There is no absolute requirement for separating address allocation
into separate functions, so simplify the driver wrapper interface
to use just if_add and if_remove instead of adding the new
alloc_interface_addr() and release_interface_addr() functions.
if_add() can now indicate if the driver forced a different interface
name or address on the virtual interface.
The server may still reject authentication at this point, so better
use conditional success decision. This allows the potentially
following EAP-Failure message to be processed properly. [Bug 354]
hostapd does not implement UAPSD functionality. However, if U-APSD
functionality is implemented outside hostapd, add support to advertise
the functionality in beacon.
Signed-off-by: yogeshp@marvell.com
Instead of parsing the IEs in the callers, use the already existing
parser in wpa_ft.c to handle MDIE and FTIE from initial MD association
response. In addition, this provides more complete access to association
response IEs to FT code which will be needed to fix FT 4-way handshake
message 2/4.
ANonce, SNonce, R0KH-ID, and R1KH-ID must match with the values
used in the previous FT authentication sequence message per
IEEE Std 802.11r-2008, 11A.8.4.
This sets the FT Capability and Policy field in the MDIE to the values
received from the target AP (if available). This fixes the MDIE contents
during FT Protocol, but the correct value may not yet be used in initial
mobility domain association.
We do not have any keys set at this point so there is no point in
adding the MIC. In addition, IEEE Std 802.11r-2008, 11A.4.2
describes this frame to have MIC IE count of 0 and MIC of 0.
This removes transmission of some unnecessary Deauthentication
frames in cases where we only need to clear the local state. In
addition, this resolves issues for 802.11r FT-over-DS by allowing
authentication state to be set locally even when no actual
Authentication frame is to be transmitted.
IEEE Std 802.11r-2008, 11A.4.2 describes FT initial mobility domain
association in an RSN to include PMKR1Name in the PMKID-List field
in RSN IE in messages 2/4 and 3/4. This makes the RSN IE not be
bitwise identical with the values used in Beacon, Probe Response,
(Re)association Request frames.
The previous versions of wpa_supplicant and hostapd did not add the
PMKR1Name value in EAPOL-Key frame and did not accept it if added
(due to bitwise comparison of RSN IEs). This commit fixes the
implementation to be compliant with the standard by adding the
PMKR1Name value into EAPOL-Key messages during FT 4-Way Handshake and
by verifying that the received value matches with the value derived
locally.
This breaks interoperability with previous wpa_supplicant/hostapd
versions.
Running hostapd and wpa_supplicant on the same interface at the same
time is not expected to work, but it should not cause hostapd to crash.
Ignore station mode association events (no addr field) to avoid this.
IF WPA/RSN parameters were changed or WPA/RSN was disabled, the
WPA/RSN IE in Beacon/Probe Response frames was only update with
set_beacon(). We need to do this with set_generic_elem(), too, to
work with all driver wrappers.
Call ieee802_11_set_beacon() in addition to set_ap_wps_ie() when
processing WPS IE updates. This is needed with drivers that use
set_beacon() instead of set_ap_wps_ie() (i.e., nl80211).
Some ER implementation (e.g., some versions of Intel PROSet) seem to
use incorrect format for WLANEventMAC variable in PutWLANResponse.
Work around this by allowing various MAC address formats to be used
in this variable (debug message will be shown if the colon-deliminated
format specified in WFA WLANConfig 1.0 is not used).
This version of the MAC address parser allows number of different
string formats for the address (e.g., 00:11:22:33:44:55, 0011.2233.4455,
001122334455, 00-11-22-33-44-55). It returns the number of characters
used from the input string in case of success.
It turns out that this is needed for both FT-over-DS and FT-over-air
when using mac80211, so it looks easiest to just unconditionally
re-configure the keys after reassociation when FT is used.
This is needed to allow reassociation processing to skip 4-way handshake
when FT-over-DS is used with an AP that has a previous association state
with the STA.
This seems to be needed at least with mac80211 when a STA is using
FT-over-DS to reassociate back to the AP when the AP still has the
previous association state.
This makes the call simpler for driver wrappers since there is no need
to parse the IEs anymore before indicating association. In addition,
this allows association processing to be extended to use other IEs
in the future.
This avoids conflict with both Label and Display being included at
the same time (which would make it difficult to figure out which
PIN was actually used).
IGTK get_seqnum needs to be skipped in the same way as GTK one when
rekeying group keys. Previously, the old PN value (the one from the
previous key) was indicated and that resulted in MMIE replay detection
at the station.
This can be used to test 802.11w by sending a protected or unprotected
deauth/disassoc frame.
hostapd_cli deauth <dst addr> test=<0/1>
hostapd_cli disassoc <dst addr> test=<0/1>
test=0: unprotected
test=1: protected
Must update sm->pairwise when fetching PMK-R1 SA.
Add a workaround for drivers that cannot set keys before association
(e.g., cfg80211/mac80211): retry PTK configuration after association.
If the PTK configuration prior to association fails, allow reassociation
attempt to continue and configure PTK after association. This is a
workaround for drivers that do not allow PTK to be configured before
association (e.g., current cfg80211/mac80211).
This attribute is supposed to indicate which methods the AP supports as
an Enrollee for adding external Registrars. It was left to 0 when the
AP code did not yet support external Registrars and was forgotten when
the ER support was added.
On NetBSD 5.0.2, wpa_supplicant build results in messages below.
../src/drivers/driver_bsd.c: In function 'wpa_driver_bsd_get_ssid':
../src/drivers/driver_bsd.c:876: warning: passing argument 2 of 'bsd_get_ssid'
from incompatible pointer type
../src/drivers/driver_bsd.c:876: warning: passing argument 3 of 'bsd_get_ssid'
makes integer from pointer without a cast
../src/drivers/driver_bsd.c:876: error: too many arguments to function
'bsd_get_ssid'
../src/drivers/driver_bsd.c: In function 'wpa_driver_bsd_scan':
../src/drivers/driver_bsd.c:1125: warning: passing argument 2 of 'bsd_set_ssid'
from incompatible pointer type
../src/drivers/driver_bsd.c:1125: warning: passing argument 3 of 'bsd_set_ssid'
makes integer from pointer without a cast
../src/drivers/driver_bsd.c:1125: error: too many arguments to function
'bsd_set_ssid'
gmake: *** [../src/drivers/driver_bsd.o] Error 1
This patch solves this issue.
This is a step in adding FT support with nl80211-based drivers.
driver_nl80211.c is now registering to handle the FT Action frames
and is able to transmit FT Request frame. Received FT Action frames
are not yet indicated as driver events.
This is needed to fix PTK derivation to use correct length. Previously,
64-octet PTK may have been derived if the authenticator did not already
have a STA entry. Now, the correct pairwise cipher suite is learned when
then PMK-R1 SA is received.
This was not supposed to have duplicate value with WPA_AUTH_ALG_LEAP.
The previous version was unable to set FT as the authentication
algorithm with nl80211.
With this patch, a client gets kicked out of the last BSS it was
attached to, when it is associating to a different one.
While mac80211 does allow a station to be present on multiple bss
interfaces, this does seem to cause problems both for the stack
and for hostapd.
This patch allows the nl80211 driver to create its own per-bss context
and pass it to the drv_priv pointer of the hostapd bss state.
With this and the following patch, stations can associate to and switch
between multiple BSS interfaces of a single wiphy.
This obsoletes a few instances of passing ifname to a callback, those
can be removed in a separate patch.
It might also be useful to move more fields from the driver data to the
per-bss data structure in the future.
This patch allows wpa_supplicant to compile on Debian's kfreebsd
architectures.
Patch by Stefan Lippers-Hollmann based on work done by Petr Salinger
and Emmanuel Bouthenot for 0.6.X (http://bugs.debian.org/480572).
filter_ssids=1 global configuration parameter can now be used to
enable scan result filtering (with -Dnl80211 only for now) based on
the configured SSIDs. In other words, only the scan results that have
an SSID matching with one of the configured networks are included in the
BSS table. This can be used to reduce memory needs in environments that
have huge number of APs.
wpa_supplicant can now be notified of suspend/resume events, e.g.,
from pm-action scripts. This allows wpa_supplicant to clear information
that may become invalid during a suspend operation.
The kernel side support for this was just added into
wireless-testing.git. This commit adds the driver wrapper code needed
to allow wpa_supplicant to use the new functionality.
Some drivers may need to use a specific ifname for the virtual
interface, so allow them to do this with a new parameter passed
to the alloc_interface_addr() handler.
TNC IF-T is somewhat unclear on this are, but
draft-hanna-nea-pt-eap-00.txt, which is supposed to define the same
protocol, is clearer on the Flags field being included.
This change breaks interoperability with the old implementation if
EAP-TNC fragmentation is used. The old version would not accept
the acknowledgement message with the added Flags octet while the
new version accepts messagss with with both options.
If the last message from the EAP-TNC server was fragmented, the
fragment processing lost the DONE/FAIL state and did not know how
to handle the final ACK from the peer. Fix this by remembering the
earlier DONE/FAIL state when fragmenting a frame.
TNC IF-T specification is unclear on the exact contents of the fragment
acknowledgement frame. An interoperability issue with the tncs@fhh
implementation was reported by Arne Welzel
<arne.welzel@stud.fh-hannover.de> due to the different interpretations
of the specification. Relax EAP-TNC server/peer validation rules to
accept fragmentation acknowledgement frames to include the Flags field
to avoid this issue.
This patch aggregates ioctls.
First is SIOCS80211. The SIOCS80211's arguments has 3 couples.
1-1. i_len, i_data
1-2. i_val
1-3. i_len, i_data, i_val (currently only IEEE80211_IOC_APPIE)
There were 3 routines for each cases. This patch aggregates these to
one.
Second is SIOCG80211. The SIOCG80211 returns 2 type of value.
2-1. i_len
2-2. i_val
There were 2 routines for each cases. This patch aggregates these to
one.
I have tested on both FreeBSD 8.0 and NetBSD 5.0.1 with these cases.
[hostapd]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(STA)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(AP)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
This patch enables FreeBSD channel control.
I have tested on FreeBSD 7.2 with these cases.
[hostapd]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(STA)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(AP)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
The attached patch unifies hostapd wpa_driver_bsd_ops and
wpa_supplicant wpa_driver_bsd_ops.
I have tested on NetBSD 5.0.1 with these cases.
[hostapd]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(STA)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
[wpa_supplicant(AP)]
RSN-PSK(CCMP)/WPA-PSK(TKIP)
This patch modifies field name of struct bsd_driver_data to use
same name of struct wpa_driver_bsd_data. This is a preparation of
unifying struct bsd_driver_data and struct wpa_driver_bsd_data.
This allows external programs (e.g., UI) to get more information
about server certificate chain used during TLS handshake. This can
be used both to automatically probe the authentication server to
figure out most likely network configuration and to get information
about reasons for failed authentications.
The follow new control interface events are used for this:
CTRL-EVENT-EAP-PEER-CERT
CTRL-EVENT-EAP-TLS-CERT-ERROR
In addition, there is now an option for matching the server certificate
instead of the full certificate chain for cases where a trusted CA is
not configured or even known. This can be used, e.g., by first probing
the network and learning the server certificate hash based on the new
events and then adding a network configuration with the server
certificate hash after user have accepted it. Future connections will
then be allowed as long as the same server certificate is used.
Authentication server probing can be done, e.g., with following
configuration options:
eap=TTLS PEAP TLS
identity=""
ca_cert="probe://"
Example set of control events for this:
CTRL-EVENT-EAP-STARTED EAP authentication started
CTRL-EVENT-EAP-PROPOSED-METHOD vendor=0 method=21
CTRL-EVENT-EAP-METHOD EAP vendor 0 method 21 (TTLS) selected
CTRL-EVENT-EAP-PEER-CERT depth=0 subject='/C=US/ST=California/L=San Francisco/CN=Server/emailAddress=server@kir.nu' hash=5a1bc1296205e6fdbe3979728efe3920798885c1c4590b5f90f43222d239ca6a
CTRL-EVENT-EAP-TLS-CERT-ERROR reason=8 depth=0 subject='/C=US/ST=California/L=San Francisco/CN=Server/emailAddress=server@kir.nu' err='Server certificate chain probe'
CTRL-EVENT-EAP-FAILURE EAP authentication failed
Server certificate matching is configured with ca_cert, e.g.:
ca_cert="hash://server/sha256/5a1bc1296205e6fdbe3979728efe3920798885c1c4590b5f90f43222d239ca6a"
This functionality is currently available only with OpenSSL. Other
TLS libraries (including internal implementation) may be added in
the future.
The previous version could end leaking memory since os_free() was used
instead of wpabuf_free(). In addition, this could potentially have
triggered a crash if the TLS context were being freed when pending
input data where still in the buffer (though, this may not be possible
to trigger in practice).
The bsd_send_eapol() adds Ethernet header by itself. This patch changes it
to use l2_packet functionality.
I have tested on NetBSD 5.0.1 with WPA-PSK(TKIP).
On NetBSD, we should configure some parameters manually out of hostapd
like below.
ifconfig ath0 mediaopt hostap
ifconfig ath0 mode 11g
ifconfig ath0 chan 6
This patch does these automatically. Maybe there will be some
objections, like "hardware configuration is not hostapd/wpa_supplican's
work". So I will write the reasons why I made this patch.
1. For usability.
2. The first command fails when previous state is adhoc. This patch is
free from previous state.
3. Some driver wrappers configure these automatically (like nl80211).
4. I have wasted time trying to find out these command were needed :(
The ps3 wireless kernel driver has wireless extension support.
There is a legacy wpa_supplicant driver, and support for this
has been removed from the kernel driver, as no distributions
are using it.
This may help in debugging why cfg80211 refused the association
command since the scan results should include information about all
pending authentication and association states.
cfg80211 has a limit on pending authentications, so we better clear
the entries that we do not care about to avoid hitting the limit
when roaming between multiple APs.
This patch moves the authentication server setup before
IEEE 802.1X initialization. It's because 802.1X already
needs to have a valid SSL context.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
This allows the driver wrappers to return two sets of IEs, so that
the BSS code can use information from both Beacon and Probe Response
frames if needed. For example, some Cisco APs seem to include more
information in Wireless Provisioning Services IE when it is in the
Beacon frame.
This makes the bridge parameter unnecessary for cases where the interface
is already in a bridge and sysfs is mounted to /sys so that the detection
code works.
For nl80211, the bridge parameter can be used to request the AP
interface to be added to the bridge automatically (brctl may refuse to
do this before hostapd has been started to change the interface mode).
If needed, the bridge interface is also created.
If the driver is detected to use cfg80211, we can rely on it being able
to disconnect with SIOCSIWMLME commands and to use empty SSID as a way
to stop it from associating when we are in progress of configuring the
driver for association. Consequently, we can remove the hack that uses
random 32-octet SSID to force disconnection and re-order association
commands to match the expectations that cfg80211 has for WEXT ioctls.
This gets rid of extra scan rounds and attempts to associate with the
silly 32-octet SSID.
Better make sure the eloop_timeout data gets fully initialized. The
current code is filling in all the fields, but it is clearer to just
zero the buffer to make sure any new field added to the structure gets
initialized.
This avoids potential use of uninitialized stack memory when printing
out peer address based on SMK error message that does not include the
MAC address.
wpa_sm_step() could theoretically free the statemachine, but it does
not do it in this particular case. Anyway, the code can be cleaned to
verify whether the state machine data is still available after the
wpa_sm_step() call.
On FreeBSD 8.0, driver_bsd.c build fails because of changes from
older versions of FreeBSD. The error messages are below:
In file included from ../src/drivers/driver_bsd.c:38:
/usr/include/net80211/ieee80211_crypto.h:94: error: 'IEEE80211_TID_SIZE'
undeclared here (not in a function)
../src/drivers/driver_bsd.c: In function 'wpa_driver_bsd_set_wpa_ie':
../src/drivers/driver_bsd.c:968: error: 'IEEE80211_IOC_OPTIE' undeclared (first
use in this function)
../src/drivers/driver_bsd.c:968: error: (Each undeclared identifier is reported
only once
../src/drivers/driver_bsd.c:968: error: for each function it appears in.)
gmake: *** [../src/drivers/driver_bsd.o] Error 1
This patch solves this issue.
wmm_ac_??_cw{min,max} parameters are in log form
When the wme_ac_??_cw{min,max} parameters aren't specified in
hostapd.conf, hostapd uses an incorrect set of default values, as the
defaults are in 2^x-1 form instead of in log form. This patch changes
them over to the expected log form.
Number of Linux driver wrappers included this more or less identical
function, so lets add a new helper file to be able to share some more
code between the driver wrappers.
The three existing enums were already depending on using the same
values in couple of places and it is just simpler to standardize on
one of these to avoid need for mapping between different enums for
the exact same thing.
Most of this file was already moved into wpa_supplicant/scan.c and
we can remove the file completely by having couple of small helper
functions copied to the remaining users outside core wpa_supplicant
code.
This fits better in wpa_supplicant/scan.c. Couple of remaining
scan_helpers.c functions are currently used in driver wrappers,
but they can likely be removed in the future.
This adds new commands and events for allowing off-channel Action
frame exchanges to be requested. This functionality is not yet used
and is only fully supported by driver_test.c at this point.
driver_nl80211.c has support for the remain-on-channel commands, but
the Action frame TX/RX part is still pending review for the kernel
code and as such, is not yet included here.
This adds placeholder code for allowing the virtual interfaces to be
pre-allocated a MAC address before the interface type is known with
drivers that do not handle interface type changes.
Get rid of wpa_supplicant_sta_rx() and add a new driver event that is
marked to be used only with driver_test.c. In addition, remove this
functionality from privsep wrapper. This is only use for client mode
MLME testing with driver_test.c.
Get more information about scans when updating BSS table information.
This allows the missing-from-scans expiration rule to work properly
when only partial set of channels or SSIDs are being scanned.
WPS IE parsing for PBC mode did not check whether the UUID-E attribute
was included before dereferencing the pointer. This could result in the
AP crashing when processing and invalid Probe Request frame.
There does not seem to be a driver interface for fetching auth_algs
capability, but this may be used by some external application, so
hardcode all auth_algs as supported for now.
This allows the driver interface to be deinitialized before
struct hostapd_data instance gets freed. This needs to be done so
that the driver wrapper does not maintain a context pointer to
freed memory.
Doxygen and some build tools may get a bit confused about same file
name being used in different directories. Clean this up a bit by
renaming some of the duplicated file names in src/ap.
Initialize struct hostapd_data driver context with the same driver
information that was initialized earlier during wpa_supplicant start.
This allows the AP mode operations to be completed directly with the
same calls in AP code without having to maintain a separate translation
layer between the AP and station mode driver context.
Skip WPS IE building for Beacon and Probe Response frames is set_ie_cb()
is not set. This fixes a memory leak and optimizes operations by not
allocating memory and building the WPS IEs unnecessarily.
This code can be shared by both hostapd and wpa_supplicant and this
is an initial step in getting the generic code moved to be under the
src directories. Couple of generic files still remain under the
hostapd directory due to direct dependencies to files there. Once the
dependencies have been removed, they will also be moved to the src/ap
directory to allow wpa_supplicant to be built without requiring anything
from the hostapd directory.
set_ap_wps_ie() is not used to set WPS IE for both Beacon and Probe
Response frames with a single call. In addition, struct wpabuf is used
instead of separate u8* and length fields. This avoids duplicated
allocation of the IEs and simplifies code in general.
This mode allows associated stations to use 4-address frames to allow
layer 2 bridging to be used. At least for the time being, this is only
supported with driver=nl80211.
This WPA_TRACE=y additions allows components to register active references
to memory that has been provided to them as a pointer. If such an actively
referenced memory area is freed, tracer will report this as an error and
backtraces of both the invalid free and the location where this pointer
was marked referenced are shown.
This adds config_methods configuration option for wpa_supplicant
following the design used in hostapd. In addition, the string is
now parsed in common code from src/wps/wps_common.c and the list
of configurable methods include all the defined methods from
WPS 1.0h spec.
Since an Enrollee that does not advertise display as one of the
Config Methods is unlikely to be able to show the ASCII passphrase
to the user, prefer PSK format with such an Enrollee to reduce key
derivation time. This can help with some low-powered devices that
would take long time to derive the PSK from the passphrase.
The use_psk_key parameter can now be used to force the Registrar to
use PSK format instead of ASCII passphrase when building a Credential
for the Enrollee. For now, this is not enabled, but it could be enabled
either based on external (to WPS) configuration or automatically set
based on some WPS attribute values from the Enrollee.
Undocumented (at least for the time being) TLS parameters can now
be provided in wpa_supplicant configuration to enable some workarounds
for being able to connect insecurely to some networks. phase1 and
phase2 network parameters can use following options:
tls_allow_md5=1
- allow MD5 signature to be used (disabled by default with GnuTLS)
tls_disable_time_checks=1
- ignore certificate expiration time
For now, only the GnuTLS TLS wrapper implements support for these.
The new TLS wrapper use may end up returning alert data and we need to
make sure here that it does not end up getting interpreted as success
due to non-NULL response.
This converts tls_connection_handshake(),
tls_connection_server_handshake(), tls_connection_encrypt(), and
tls_connection_decrypt() to use struct wpa_buf to allow higher layer
code to be cleaned up with consistent struct wpabuf use.
Use an extra header to move the returned pointer to break os_free()
or free() of the returned value and verify that the correct magic
is present when freeing or resizing the wpabuf. Show backtrace on
invalid wpabuf use.
If Finished message from peer has been received before the server
Finished message, start Phase 2 with the same message to avoid extra
roundtrip when the peer does not have anything to send after the server
Finished message.
Instead of forcefully deinitializing ER immediately, give it some
time to complete unsubscription and call eloop_terminate() only once
ER code has completed its work.
WPA_TRACE=y builds will now verify that memory allocation in done
consistently using os_{zalloc,malloc,realloc,strdup,free} (i.e., no
mixing of os_* functions and unwrapper functions). In addition, some
common memory allocation issues (double-free, memory leaks, etc.) are
detected automatically.
WPA_TRACE=y can now be used to enable internal backtrace support that
will provide more details about implementation errors, e.g., when some
resources are not released correctly. In addition, this will print out
a backtrace automatically if SIGSEGV is received.
As an initial step in sharing netlink helper functions among driver
wrappers, create a new file for netlink code and move operstate send
function there.
This message from tls_connection_handshake() is not really an error in
most cases, so do not show it if there was indeed no Application Data
available (which is a normal scenario and not an indication of any
error).
Replace driver wrapper calls to hostapd_tx_status(),
hostapd_rx_from_unknown_sta(), hostapd_mgmt_rx(), and
hostapd_mgmt_tx_cb() with new generic driver events
EVENT_TX_STATUS, EVENT_RX_FROM_UNKNOWN, and EVENT_RX_MGMT.
This cleans up lot of the driver wrapper code to be less dependent
on whether it is being used within wpa_supplicant AP mode or hostapd.
This remove the need from driver_test.c to go through internal hostapd
structures to find the appropriate BSS when reporting events on secondary
BSSes.
This removes need for including hostapd/sta_flags.h into driver
wrappers and removes any remaining dependencies between driver flags
and internal hostapd flags.
The Prism54.org project seems have been dead for a while and it does not
look like this driver would ever be maintained again. Furthermore, it is
difficult to find a version that would work with the driver_prism54.c
wrapper and there is another driver for these card in the Linux kernel
tree.
The hostapd integration in driver_prism54.c is quite different from the
other driver wrappers and would require major effort to get it cleaned
up. Since there does not seem to be any real users for the cleaned up
version, there does not seem to be justification to spend this effort on
the wrapper. This old code is making it much more difficult to clean up
the driver interface and at this point, the best option seems to be to
remove the driver wrappers. Should someone really still need this, the
old code will continue to be available in hostapd 0.6.x.
Instead of using the latest selected registrar change, collect selected
registrar information separately from all registrars and use the union
of this information when building the WPS IE for Beacon and Probe
Response frames.
Note: SetSelectedRegistrar UPnP action does not include a unique
identifier, so the ER matching routine is based only on the IP address
of the ER. In theory, there could be multiple ERs using the same IP
address (but different port or URL), so there may be some corner cases
that would not always match the correct ER entry at the AP. Anyway, this
is not really expected to occur in normal use cases and even if it did
happen, the selected registrar information is not any worse than it was
before when only the last change from any registrar for being
advertized.
This is more logical location for checking the URL and potentially
handling a call to another URL handler. In addition, return 404 error,
not invalid UPnP action, if the URL does not match.
These callbacks can be handled internally within core WPS code, so there
is no need to go through wps_hostapd.c with a callback function that is
just calling back into the core WPS code.
This can be handled internally within core WPS code, so there is no
need to go through wps_hostapd.c with a callback function that is just
calling back into the core WPS code.
IEEE 802.11w uses distinct key indexes (4 and 5) so the same
get_seqnum() handler can be used to fetch packet number for both
TKIP/CCMP and BIP(using IGTK).
Since the new get_seqnum_igtk() handler was not actually implemented by
any driver wrapper, this may also fix BIP/IGTK sequence number reporting
with driver_nl80211.c.
The password in User-Password AVP is padded to a multiple of 16 bytes
on EAP-TTLS/PAP. But when the password length is zero, no padding is
added. It doesn't cause connectivity issue. In fact, I could connect
with hostapd RADIUS server with zero length password.
I think it's better for obfuscation to pad the 16 bytes data when the
password length is zero with this patch.
There was code for configuring this, but no driver wrapper actually
implements the actual setting. Remove this for now to reduce potential
confusion and to simply the driver interface.
In addition to the bitrate, the only other variable in this structure
is used internally in hostapd. Move this structure into hostapd.h and
make the driver API use simpler data structure (array of bitrates).
These are not really used and can be removed to clean up the driver
interface definition. The only remaining flag (HOSTAPD_RATE_BASIC) can
be removed once the basic rate set indication can be handled
differently.
if_add/if_remove can now be used as the generic driver ops for adding
and removing virtual interfaces of various types. In addition,
driver_nl80211.c is now including this code unconditionally, so that
the functions are not limited only for hostapd.
On NetBSD 5.0.1, driver_bsd.c build fails with message below.
../src/drivers/driver_bsd.c: In function 'wpa_driver_bsd_associate':
../src/drivers/driver_bsd.c:1170: warning: implicit declaration of function 'wpa_driver_bsd_set_auth_alg'
../src/drivers/driver_bsd.c: At top level:
../src/drivers/driver_bsd.c:1204: error: static declaration of 'wpa_driver_bsd_set_auth_alg' follows non-static declaration
../src/drivers/driver_bsd.c:1170: error: previous implicit declaration of 'wpa_driver_bsd_set_auth_alg' was here
gmake: *** [../src/drivers/driver_bsd.o] Error 1
This patch solves this issue.
The new test-asn1 and test-x509 tools are built using libraries
from src/{utils,crypto,tls}. Currently, cross dependencies between
crypto and tls are still preventing the test-x509 from being linked
properly.
This is a separate program and is used mainly with hostapd, so it is
better to move this into the hostapd subdirectory now that Milenage
code has already been moved into src/crypto. Milenage was the only
generic component in hlr_auc_gw.
eap_example is now using src/crypto/libcrypto.a and src/tls/libtls.a
instead of providing own rules for building the files for these
components. TLS library selection is temporarily disabled for
eap_example (it will be built using internal crypto/TLS), but the
configuration option for this will eventually be restored with a new
libcrypto.a configuration option.
Clean up the internal TLS implementation by removing conditional
build blocks for (mostly) EAP-FAST specific functionality. This
will increase the size a big for non-EAP-FAST builds, but is quite
helpful in making src/tls/libtls.a with single build options. If
the potential size reduction is considered significant in the future,
this can be reconsider with a more library compatible way (e.g.,
external file with registration function, etc.).
This allows libeap.a and libeap.so to be built by merging in multiple
libraries from src subdirectories. In addition, this avoids wasting
extra space and time for local builds.
This fixes issues with some GnuTLS versions that seem to be adding
quite a bit of extra data into TLS messages. The EAP server code is
now using the same 300 byte extra room that was already used in the
EAP peer implementation.
The following defines are not really needed in most places, so
remove them to clean up source code and build scripts:
EAP_TLS_FUNCS
EAP_TLS_OPENSSL
EAP_TLS_GNUTLS
CONFIG_TLS_INTERNAL
There seem to be some cases in which wpa_supplicant and
cfg80211/mac80211 seem to have different understanding on
authentication/association state. Since cfg80211/mac80211 is very strict
on when it accepts new authentication/association/scan commands, try our
best at clearing such state mismatches by explicitly deauthenticating
from BSSes with which the driver claims we are associated with if we do
not have local information about such association.
Print what the kernel believes the current BSS status (authenticated
or associated) is in scan results. In addition, check whether this
matches with the state that wpa_supplicant believes the driver to be
in.
This does not change the actual behavior, but will provide information
that will help in debugging potential issues where cfg80211/mac80211
seems to get into a different state from wpa_supplicant. In addition,
this provides an easy location for a workaround that could be added to
clear cfg80211/mac80211 state for unknown BSSes.
This is an initial step in further cleaning up the EAPOL authenticator
use to avoid requiring direct accesses to the internal data structures.
For now, number of external files are still including the internal
definitions from eapol_auth_sm_i.h, but eventually, these direct
references should be removed.
In addition, start ordering header file includes to be in more
consistent order: system header files, src/utils, src/*, same
directory as the *.c file.
This removes the hardcoded definition from Makefile and cleans up
source code by moving the mail HOSTAPD_DUMP_STATE blocks into separate
files to avoid conditional compilation within files.
While this may not include knowledge of all EAP methods since this
depends on build configuration, it is better to not have to include
ieee802_1x.h into eapol_sm.c.
This makes it clearer which files are including header from src/common.
Some of these cases should probably be cleaned up in the future not to
do that.
In addition, src/common/nl80211_copy.h and wireless_copy.h were moved
into src/drivers since they are only used by driver wrappers and do not
need to live in src/common.
This avoids passing the raw scan results into the RSN code and by
doing so, removes the only dependency on src/drivers from the
src/rsn_supp code (or from any src subdirectory for that matter).
Instead of using hardcoded maximum A-MPDU length of 64 kB and no
restrictions on minimum MPDU Start Spacing, use the correct values
reported by the driver.
This is not actually used at all and it looks like the rules for
maintaining the old/new RADIUS configuration are not very clear in the
case the RADIUS client configuration did not change. Consequently, it
is better to just remove this for now and if similar functionality is
ever needed, redesign it to be easier to use without causing hard to
find issues with using freed memory.
Simpler approach to reconfiguring the RADIUS client would involve
just deinitializing the old context unconditionally and initializing
a new one whenever the configuration could have changed.
Use shared functions for converting Primary Device Type between binary
and string formats. In addition, use array of eight octets instead of a
specific structure with multiple fields to reduce code complexity.
Mainly, this is including header files to get definitions for functions
which is good to verify that the parameters match. None of these are
issues that would have shown as incorrect behavior of the program.
This gets rid of previously deprecated driver_ops handlers set_wpa,
set_drop_unencrypted, set_auth_alg, set_mode. The same functionality
can be achieved by using the init/deinit/associate handlers.
These driver wrappers should not be used anymore; WEXT should be used
instead. However, there may still be users stuck on older kernel versions
that may require driver specific wrappers, so the source code still
remains in the repository.
This moves the MTU definition into driver_hostap.c since it was really
meant to be specific to this driver. Since this was the last remaining
definition in hostapd_defs.h, remove that header file as unnecessary.
This code was copied from driver_hostap.c where it is used with the
special wlan#ap interface. It was not supposed to be used to change
the MTU for a normal data interface.
Clean up driver_nl80211.c by gettign rid of the last remaining WEXT use.
This requires that a recent mac80211 version is used to get full protection
in station mode via the authorized flag (IEEE 802.1X PAE).
Clean up driver interface by merging hostapd and wpa_supplicant
specific set_beacon driver_ops into a single one. In addition,
merge set_beacon_int into to the same operation.
If initialization fails, we could potentially try to sendto() on -1
socket which would fail. No point in doing that, so just return early
from the function.
The current MinGW/w32api versions seem to provide all the needed CryptoAPI
functions, so the code for loading these dynamically from the DLL can be
removed.
Need to define the workspace buffer properly to allow compiler to handle
strict aliasing between the incoming unsigned char[64] buffer as an u32
array. The previous version built with strict aliasing enabled can
result in SHA-1 producing incorrect results and consequently, with
4-way handshake failing.
This is based on a report and patch from Dan Williams <dcbw@redhat.com>
but with a different type (the union) used as a fix to avoid needing
extra type casting.
Discovered as part of the investigation of:
https://bugzilla.redhat.com/show_bug.cgi?id=494262#c32
if sha1 is built with gcc without turning off strict aliasing, it will
fail to correctly generate the hashes and will fail its own testcases as
well.
Signed-off-by: Dan Williams <dcbw@redhat.com>
This avoids some issues in cases where the ER has been started and
stopped multiple times on the same address and an AP may have stored
multiple event notification addresses for the same ER. The random
identifier allows the ER to filter out unexpected messages from further
processing.
Do not give the allocated memory to the subscription code since it was
not using it as-is anyway. This makes it easier to understand who owns
the allocation an is responsible of freeing it. This may potentially
fix some memory leaks on error paths.
The WPS 1.0h specification is quite unclear on what exactly should be
used as the MAC Address value in the Credential and AP Settings. It
looks like this should after all be the MAC Address of the Enrollee,
so change Registrar implementation to use that address instead of the
AP BSSID.
In addition, add validation code to the Enrollee implementation to
check the MAC Address value inside Credential (and also inside AP Settings)
to make sure it matches with the Enrollee's own address. However, since
there are deployed implementations that do not follow this interpretation
of the spec, only show the mismatch in debug information to avoid breaking
interoperability with existing devices.
This will need some additional code in wps_er_pbc() to handle PBC mode
enabling for a single AP only. For now, this can only be expected to work
when the ER is connected to a single AP.
UPnP device architecture specification requires all evented variables to
be included in the initial event message after subscription. Since this
can happen before we have seen any events, generated a dummy event
(WSC_ACK with all-zeros nonces) if needed.
This will notify control points of the services going away and allows
them to notice this without having to wait timeout on the
initial advertisements.
This removes following WFA WLANConfig Service actions and the related
state variables: GetAPSettings, SetAPSettings, DelAPSettings,
GetSTASettings, SetSTASettings, DelSTASettings, RebootAP,
ResetAP, RebootSTA, ResetSTA.
While WFA WLANConfig Service version 1.0 claims that some of these are
mandatory to implement for an AP, there are no known implementations
supporting these actions neither in an AP/proxy or an External Registrar
that would use them. These are unlikely to be supported in the future
either and as such, it is just simpler to get rid of them to clean up
the implementation and reduce code size.
When using UPnP transport, the Op-Code is not included, but the WPS
frame processing will need this. Generate a matching Op-Code based
on the message type.
Previously, WSC_MSG was hardcoded for every message from ER, but
this needs to be changed based on message type to send a valid
message to the Enrollee via EAP transport.
New PINs can now be added to WPS ER. This results in the ER code
using SetSelectedRegistrar to modify AP state so that Enrollees
will be able to notice the actice registrar more easily.
This keeps STA/Enrollee entries up to date and sets up registration
protocol session. M1 is processed and M2D generated, but the there
is no code yet to transmit the response back to the AP with
PutWLANResponse.
Always bring down the wlan interface, even when not changing the
BSSID, the interface also needs to be down for changing its type
from managed to AP mode.
The receive Probe Request and EAP-WSC notifications are now parsed
(including the TLVs in them) and contents is shown in the debug log.
Actual processing of the received information is still missing (TODO
comments indicate the needed functionality).
rand would be the address of rand() function and never NULL. The previous
version could have crashed on invalid AKA-AUTS command. Though, these
commands are only from hostapd which sends valid requests and as such,
the actual issue did not show up.
This is like wpa_msg(), but the output is directed only to
ctrl_interface listeners. In other words, the output will not be
shown on stdout or in syslog.
Change scan result reporting to use wpa_msg_ctrl() for
CTRL-EVENT-SCAN-RESULTS message at info level and wpa_printf() at
debug level to avoid showing scan result events in syslog in the
common configuration used with NetworkManager.
This adds code to start a HTTP server and to subscribe to UPnP events
from each discovered WPS AP. The event messages are received, but there
is not yet any code to actually parse the contents of the event.
Clean up code so that UPnP implementation does not need to include all
the HTTP functionality. In addition, make it easier to share HTTP server
functionality with other components in the future.
Instead of implementing HTTP client functionality inside
wps_upnp_event.c, use a generic HTTP client module to do this. The HTTP
client code can now be shared more easily for other purposes, too.
This is the first step in adding support for using wpa_supplicant as a
WPS External Registrar to manage APs over UPnP. Only the device
discovery part is implemented in this commit.
While the actual use here would be unlikely to be broken by any C
optimization, it is better to use explicit union construction to let
gcc know about the aliasing and avoid warnings from gcc 4.4.
gcc 4.4 ends up generating strict-aliasing warnings about some very common
networking socket uses that do not really result in a real problem and
cannot be easily avoided with union-based type-punning due to struct
definitions including another struct in system header files. To avoid having
to fully disable strict-aliasing warnings, provide a mechanism to hide the
typecast from aliasing for now. A cleaner solution will hopefully be found
in the future to handle these cases.
Though we have such a timeout when handling SetSelectedRegistrar UPnP
message from an external registrar, it looks like we don't have one when
the internal registrar is activated for PIN connection. Thus we set the
SelectedRegistrar flag when AP is activated for PIN connection but we
never reset it - not by some timeout, nor when registration succeeds.
This lead to situations where AP everlastingly declare that it is
activated for WPS PIN connection when in reality it is not.
Use the same timeout (and also success with PIN) to clear the selected
registrar flag when using internal registrar, too.
If PBC session overlap is detected during an ongoing PBC protocol run,
reject the run (if M8, i.e., credentials, have not yet been sent). This
provides a bit longer monitoring time at the Registrar for PBC mode to
catch some cases where two Enrollees in PBC mode try to enroll
credentials at about the same time.
This provides information about PBC mode result from the WPS Registrar
module. This could be used, e.g., to provide a user notification on the
AP UI on PBC failures.
If PBC session overlap is detected between button press on the registrar
and M1 is reception, report session overlap with the Config Error
attribute in M2D to the Enrollee.
This functionality fits better with src/tls (i.e., internal TLS
implementation), so move it there to make crypto_internal.c more
of a wrapper like other crypto_*.c files.
Private keys can now be used in either unencrypted or encrypted
PKCS #8 encoding. Only the pbeWithMD5AndDES-CBC algorithm (PKCS #5)
is currently supported.
Recognize the PEM header "BEGIN PRIVATE KEY" as base64-decode the data
to be able to use PEM encoded, unencrypted PKCS#8 private keys with the
internal TLS implementation. Previously, only DER encoding of the
PKCS#8 private key was supported.
OpenSSL 0.9.7 does not include get_rfc3526_prime_1536() function, so
provide that functionality internally if needed. In addition, make
sha256_vector() building depend on whether SHA256 support is included
in the OpenSSL library. This with CONFIG_INTERNAL_SHA256=y in .config
allows OpenSSL without SHA256 support to be used.
Both hostapd/wpa_supplicant compilation fails on DragonFly BSD.
This patch solves this issue.
I have tested only compilation. Not functionality.
Because I don't have any device which can work on DragonFly BSD.
mac80211 does not currently allow (re)authentication when we are already
authenticated. In order to work around this, force deauthentication if
nl80211 authentication command fails with EALREADY. Unfortunately, the
workaround code in driver_nl80211.c alone is not enough since the
following disconnection event would clear wpa_supplicant authentication
state. To handle this, add some code to restore authentication state
when using userspace SME.
This workaround will hopefully become unnecessary in some point should
mac80211 start accepting new authentication requests even when in
authenticated state.
Reorganize the TLS/crypto library segments into a single set of blocks
for each library instead of multiple locations handling library-specific
operations. Group crypto functionality together and get wpa_supplicant
and hostapd Makefile closer to eachother in order to make it easier to
eventually move this into a shared makefile.
Crypto library wrappers can now override the internal DH (group 5)
implementation. As a starting point, this is done with OpenSSL. The
new mechanism is currently available only for WPS (i.e., IKEv2 still
depends on the internal DH implementation).
Replace "nl80211: Ignored unknown event (cmd=33)" with
"nl80211: Scan trigger" to make debug output clearer. We do not
currently do anything with this event apart from showing it in
the debug log.
This allows NSS to be used to derive EAP-TLS/PEAP/TTLS keying material.
NSS requires a patch from
https://bugzilla.mozilla.org/show_bug.cgi?id=507359
to provide the new API. In addition, that patch needs to be modified to
add the 16-bit context length value in SSL_ExportKeyingMaterial() only if
contextlen != 0 in order to match with the EAP-TLS/PEAP/TTLS use cases.
This issue seems to be coming from the unfortunate incompatibility in
draft-ietf-tls-extractor-07.txt (draft-ietf-tls-extractor-00.txt would
have used compatible PRF construction).
At this point, it is unclear how this will be resolved eventually, but
anyway, this shows a mechanism that can be used to implement EAP key
derivation with NSS with a small patch to NSS.
This brings in the first step in adding support for using NSS
(Mozilla Network Security Services) as the crypto and TLS library
with wpa_supplicant. This version is able to run through EAP-PEAP
and EAP-TTLS authentication, but does not yet implement any
certificate/private key configuration. In addition, this does not
implement proper key fetching functions either, so the end result
is not really of much use in real world yet.
On DragonFly BSD, wired IEEE 802.1X fails with this message:
ioctl[SIOC{ADD/DEL}MULTI]: Invalid argument
This patch solves this issue.
I have tested with these:
OS : DragonFly BSD 2.4.0
EAP : EAP-TLS
Switch : Cisco Catalyst 2950
This reverts commit 5aa9cb5cca.
The nested key attribute is using different attribute values
(NL80211_KEY_* vs. NL80211_ATTR_KEY_*), so cannot share the same routine
for these purposes..
Current wpa_supplicant has a bug with WEP keys, it adds a zero-length
sequence counter field to netlink which the kernel doesn't accept.
Additionally, the kernel API slightly changed to accept keys only when
connected, so we need to send it the keys after that. For that to work
with shared key authentication, we also include the default WEP TX key
in the authentication command.
To upload the keys properly _after_ associating, add a new flag
WPA_DRIVER_FLAGS_SET_KEYS_AFTER_ASSOC_DONE indicating that the driver
needs the keys at that point and not earlier.
Commit 0b55b934ee broke this by not
initializing drv->ap = 1 in hostapd case since the mode updating
code ended up unlinking the socket file. Setting drv->ap = 1
removes the mode change and as such, unlinking of the socket file.
It is simpler to just build in all the test driver code regardless
of whether this is for hostapd or wpa_supplicant (which will eventually
get AP mode support with driver_test, too).
radius_server_encapsulate_eap() resets sess->eap->if->eap{Success,Fail}
to FALSE, such that the completion condition is never true.
The net effect is that completed sessions would linger for
RADIUS_SESSION_TIMEOUT seconds.
Signed-off-by: Alex Badea <vamposdecampos@gmail.com>
Previously, the default settings allowed 100 sessions in 60 seconds.
With this fix, the default limit is now 100 sessions per 10 seconds.
[Bug 329]
Store a copy of device attributes during WPS protocol run and make it
available for external programs via the control interface STA MIB
command for associated stations. This gives access to device name and
type which can be useful when showing user information about associated
stations.
wpa_supplicant can now reconfigure the AP by acting as an External
Registrar with the wps_reg command. Previously, this was only used
to fetch the current AP settings, but now the wps_reg command has
optional arguments which can be used to provide the new AP
configuration. When the new parameters are set, the WPS protocol run
is allowed to continue through M8 to reconfigure the AP instead of
stopping at M7.
This is an initial step in adding support for the new connect command.
For now, we just add the capability query. The actual use of the new
command will be added separately.
This is a patch for OpenBSD wired IEEE 802.1X. This is only for wired,
not wireless, because OpenBSD uses wpa_supplicant only on wired now.
http://www.openbsd.org/cgi-bin/cvsweb/ports/security/wpa_supplicant/
I have tested with these.
OS : OpenBSD 4.5
EAP : EAP-TLS
Switch : CentreCOM 8724SL
Previously, both the command replies and unsolicited events were
received from the same socket. This could cause problems if an event
message is received between a command and the response to that command.
Using two sockets avoids this issue.
When Linux has Path MTU discovery enabled, it sets by default the DF bit
on all outgoing datagrams, also UDP ones. If a RADIUS message is bigger
than the smallest MTU size to the target, it will be discarded.
This effectively limits RADIUS messages to ~ 1500 Bytes, while they can
be up to 4k according to RFC2865. In practice, this can mean trouble
when doing EAP-TLS with many RADIUS attributes besides the EAP-Message.
[Bug 326]
When Linux has Path MTU discovery enabled, it sets by default the DF bit
on all outgoing datagrams, also UDP ones. If a RADIUS message is bigger
than the smallest MTU size to the target, it will be discarded.
This effectively limits RADIUS messages to ~ 1500 Bytes, while they can
be up to 4k according to RFC2865. In practice, this can mean trouble
when doing EAP-TLS with many RADIUS attributes besides the EAP-Message.
[Bug 326]
These could, at least in theory, be used to generate unexpected common
name or subject alternative name matches should a CA sign strings with
NUL (C string termination) in them. For now, just reject the certificate
if an embedded NUL is detected. In theory, all the comparison routines
could be made to compare these strings as binary blobs (with additional
X.509 rules to handle some exceptions) and display NUL characters
somehow. Anyway, just rejecting the certificate will get rid of
potential problems with the C string getting terminated and it should
not really be used in certificates, so this should not break valid use
cases.
The BLOCK_SIZE define can be made more specific by using AES_ prefix and
by moving it to aes.h. After this, most aes-*.c do not really need to
include anything from the internal aes_i.h header file. In other words,
aes_i.h can now be used only for the code that uses the internal AES
block operation implementation and none of the code that can use AES
implementation from an external library do not need to include this
header file.
Better not specify EVP_CIPHER again for the second init call since that
will override key length with the default value. The previous version
was likely to work since most use cases would be likely to use the
default key length. Anyway, better make this handle variable length
ciphers (mainly, RC4), too, just in case it is needed in the future.
This is not really of that much use since rc4_skip() can be used as
easily. In addition, rc4 has caused some symbol conflicts in the past,
so it is easier to live without that as an exported symbol.
wpa_supplicant can now be built with FIPS capable OpenSSL for FIPS mode
operation. Currently, this is only enabling the FIPS mode in OpenSSL
without providing any higher level enforcement in wpa_supplicant.
Consequently, invalid configuration will fail during the authentication
run. Proper configuration (e.g., WPA2-Enterprise with EAP-TLS) allows
the connection to be completed.
Instead of using low level, digest-specific functions, use the generic
EVP interface for digest functions. In addition, report OpenSSL errors
in more detail.
Some crypto libraries can return in these functions (e.g., if a specific
hash function is disabled), so we better provide the caller a chance to
check whether the call failed. The return values are not yet used
anywhere, but they will be needed for future changes.
On NetBSD 5.0, when I use wired 802.1X, "Invalid argument" occurs
on SIOCADDMULTI ioctl and 802.1X fails.
I tried FreeBSD code, but "Address family not supported by protocol family"
occurs on SIOCADDMULTI ioctl and 802.1X fails, too.
This patch solves this issue.
I have tested with these:
OS : NetBSD 5.0
EAP : EAP-MD5
Switch : CentreCOM 8724SL
This is a (hopefully) temporary workaround to allow the same source code
tree to be used for building hostapd and wpa_supplicant without having
to manually force recompilation of some files. Currently, some of the
driver wrapper files need to be built separately for hostapd and
wpa_supplicant (#ifdef's in the files based on AP functionality).
This is somewhat racy as far as parallel make execution is concerned,
i.e., it may be necessary to run "make -j#" twice (plain "make" works
fine. Since this is supposed to be a temporary workaround, there is not
much point in trying to fix this with any more complex make processing.
Instead of having all driver stuff collected across wpa_supplicant
and hostapd, create a common snippet that they both include and
that handles the build configuration.
If base64_encode() were to be used with a huge data array, the
previous version could have resulted in overwriting the allocated
buffer due to an integer overflow as pointed out in
http://www.freebsd.org/cgi/query-pr.cgi?pr=137484. However, there
are no know use cases in hostapd or wpa_supplicant that would do that.
Anyway, the recommended change looks reasonable and provides additional
protection should the base64_encode() function be used for something
else in the future.
Current wpa_supplicant has a bug with WEP keys, it adds a zero-length
sequence counter field to netlink which the kernel doesn't accept.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
hostapd currently tries to encrypt all auth frames,
except for "OPEN" and "SHARED with transaction 3".
This means that it will send an encrypted "unknown
auth algorithm" reply for all other algorithsm. Fix
this by changing the logic to only encrypt shared
key auth frames with transaction 3.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Change existing CONFIG_LIBNL20 compatibility code in
driver_nl80211.c to be used by both wpa_supplicant
and hostapd, but take care of nl_handle too now.
Propagate CONFIG_LIBNL20 out of .config file and onto
CFLAGS in the Makefile.
Use libnl-gen now too.
Signed-off-by: Jon Loeliger <jdl@bigfootnetworks.com>
---
This removes need for local configuration to ignore *.o and *~
and allows the src/*/.gitignore files to be removed (subdirectories
will inherit the rules from the root .gitignore).
This attribute is not supposed to be used in the response frame (i.e.,
it is only in the EAP-Request/SIM-Notification frame) per RFC 4186
chapters 10.1 and 9.9. This is a minor bug since the server is required
to ignore the contents of the EAP-Response/SIM-Notification during
protected result indication per chapter 6.2.
EAP-AKA peer was already following the similar specification in RFC 4187,
but this was somehow missed in the EAP-SIM peer implementation.
The driver wrappers should not need to include wps_hostapd.h, so let's
make this easier by introducing a driver callback for reporting Probe
Request frames.
Since we do not currently support changing the AP settings received
from M7, there is no point in actually sending out the M8 that would
likely trigger the AP to reconfigure itself and potentially reboot.
For now, we just receive the AP settings in M7 and add a local network
configuration block based on those, but NACK the message. This makes
wps_reg work like wps_pin, but by using the AP PIN instead of a client
PIN.
Old way does not work with all drivers on NetBSD and FreeBSD are
also using this so should be a safe change. [Bug 312]
Signed-off-by: Roy Marples <roy@marples.name>
Add generic functions to get/set 80211 vars, set 80211 params and
get/sid ssid.
Change NetBSD defines to match the ioctl used for portability.
Check size we're copying into instead of assuming IFNAMSIZ.
Signed-off-by: Roy Marples <roy@marples.name>
If hostapd segfaults, or is killed with -9, or the interface already exists,
when the interface is created, it will fail.
Configuration file: /tmp/hostapd/hostapd.conf
Failed to create interface mon.wlan0_0.
Using interface wlan0_0 with hwaddr 00:13:01:01:08:0a and ssid 'IG_0405_LAN'
Failed to set beacon head/tail or DTIM period
Failed to create interface wlan0_1.
Try to remove the interface and re-create it before aborting.
To ensure the supplicant starts and ends with a clean slate (keys are
already cleaned up at init and deinit time), force a null BSSID and
bogus SSID to ensure the driver isn't connected to anything.
Signed-off-by: Dan Williams <dcbw@redhat.com>
4853d5ac84 had a small bug in the order
of these function calls in _wext_deauthenticate() (_disassociate()
did have the correct order). The deauthentication frame is supposed
to go out (if driver supports that) before we disconnect more
forcefully.
Otherwise the driver might interpret the request as a request to
create/join a new adhoc network with the bogus SSID.
Signed-off-by: Dan Williams <dcbw@redhat.com>
hostapd_cli wps_pin command can now have an optional timeout
parameter that sets the PIN lifetime in seconds. This can be used
to reduce the likelihood of someone else using the PIN should an
active PIN be left in the Registrar.
The attached patch will replace get_scan_results with get_scan_results2.
This is a preparation for WPS on BSD.
And I erased "wpa_scan_result_compar". Because scan result
sorting will be done with "wpa_scan_result_compar" on
"scan_helpers.c".
I have done below tests on NetBSD with an atheros card.
- WPA2-PSK(CCMP)
- WPA-PSK(TKIP)
- PEAP(MSCHAPv2)
- EAP-TLS
- EAP-TTLS(MSCHAPv2)
This adds a cleaner mechanism for protecting against unauthorized
data frames than the previously used drop_unencrypted mechanism
(which is not even available with nl80211 and had to use a WEXT
ioctl.
The old drop_unencrypted code is left in for now as the final
surviving WEXT use in driver_nl80211.c. However, it can be removed
from the build by defining NO_WEXT. It may also be removed
eventually when most users are expected to be using recent enough
kernel version.
For now, the old code using NL80211_ATTR_STA_FLAGS is left in for
backwards compatibility with older kernel versions. It may be removed
eventually when most users are expected to be running with new
enough kernel version.
Some deployed implementations seem to advertise incorrect information
in this attribute. For example, Linksys WRT350N seems to have a
byteorder bug that breaks this negotiation. In order to interoperate
with existing implementations, assume that the Enrollee supports
everything we do.
Attached is a patch for the RoboSwitch driver in trunk. It is a
general revision of the source code.
Changes:
- Improved IEEE 802.1X conformance ([1])
- Better conformity to Broadcom specifications
- Fixed compatibility with different chipset revisions
It is worth noting that performance may drop a little using the new
driver. This can be overcome by using "multicast_only=1" as a
parameter. In that case only packets to the PAE group address are
regarded, as the previous revision of the driver did. A more detailed
description of the parameter and it's consequences is available at [2]
(summary: use "multicast_only=1" whenever possible).
[1] http://lists.shmoo.com/pipermail/hostap/2009-February/019398.html
[2] http://forum.openwrt.org/viewtopic.php?id=19873
None of the driver wrappers user this. hostapd-controlled broadcast SSID
hiding can only be used with drivers that use hostapd for handling
Beacon and Probe Request/Response frames.
None of the driver wrappers use this. Only the drivers that use hostapd
for Beacon and Probe Request/Response handling can now use IEEE 802.11d
properly.
Note: This changes values for existing NL80211_ATTR_MAX_SCAN_IE_LEN
and NL80211_ATTR_KEY_TYPE (for some reason, they ended up getting
swapped in wireless-testing.git) and as such, could break Michael
MIC error reporting (well, at least partially).
When in AP mode, wpa_supplicant is now enabling WPS (only Internal
Registrar). wpa_cli wps_pbc and wps_pin commands can be used to initiate
WPS negotiation similarly to how this is done in station mode (though,
the BSSID parameter is ignored).
There is no point in trying to continue if a 4-way handshake frame is
discarded or if PTK/GTK/IGTK configuration fails. Force the client to
disconnect in such a case to avoid confusing user by claiming the
connection was successfully completed.
These driver wrappers use UNIX domain sockets and as such, won't be
built with Microsoft compiler. Consequently, use of C99-style designated
initializers can be used to make these files easier to maintain. Only
driver_ndis.c needs to support the old C89-style due to Microsoft
compiler not supporting newer C standard.
This was not really supported by any of the included driver wrappers. If
this functionality is desired in the future, this (or something similar)
can be added with the changes needed into a driver wrapper to use the
mechanism.
This simplifies driver wrapper operations and removes last direct
struct hostapd_data dereferences from driver_nl80211.c. In addition,
some of the TX callbacks are now fixed for secondary BSSes.
This fixes deauth/disassoc frames in secondary BSSes when using
multi-BSSID. In addition, it reduces need to dereference
struct hostapd_data inside driver wrappers.
NO_WEXT can be defined to disable all remaining WEXT uses from
driver_nl80211.c. This breaks some functionality, so the code is still
in use by default. Anyway, the new #ifdef blocks make it easy to search
for areas that need to be converted to nl80211.
Instead of adding a new driver_ops for fetching neighbor BSS data (that
nl80211 driver interface had to scan during initialization), share the
same scan operations that wpa_supplicant is using. This gets rid of
duplicated scan code in driver_nl80211.c (and better yet, removes large
part of old WEXT code).
hostapd interface initialization is now completed in a callback, if
needed, i.e., he_features channel/hw_mode selection can use as much time
as needed. This can also help with radar detection in the future.
hostapd ended up with unregistered send_mlme() in commit
9f324b61ba. Fix this by registering the
handler both for wpa_supplicant-AP and hostapd use. [Bug 310]
Use a parameter structure to pass in information that can be more easily
extended in the future. Include some of the parameters that were
previously read directly from hapd->conf in order to reduce need for
including hostapd/config.h into driver wrappers.
This was not documented properly and was not really used nor would it be
suitable to be used in generic way as it was implemented. It is better
to just remove the parameter since there does not seem to be any
reasonable use for it.
nl80211 interface has a trivial bug that prevents it to work correctly
with channel 14. Channel frequency is erroneously 2848 instead of 2484.
To correct it just apply this patch. [Bug 308]
This merges the driver wrapper implementations to use the same
implementation both for hostapd and wpa_supplicant operations to avoid
code duplication.
This commit merges the driver_ops structures and implementations from
hostapd/driver*.[ch] into src/drivers. This is only an initial step and
there is room for number of cleanups to share code between the hostapd
and wpa_supplicant parts of the wrappers to avoid unnecessary source
code duplication.
Need to set WEP keys before requesting authentication in order to get
Shared Key authentication working. Previously, the WEP keys were not set
at all when using SME in wpa_supplicant.
IEEE 802.11r KDF uses key length in the derivation and as such, the PTK
length must be specified correctly. The previous version was deriving
using 512-bit PTK regardless of the negotiated cipher suite; this works
for TKIP, but not for CCMP. Update the code to use proper PTK length
based on the pairwise cipher.
This fixed PTK derivation for both IEEE 802.11r and IEEE 802.11w (when
using AKMP that specifies SHA-256-based key derivation). The fixed
version does not interoperate with the previous versions. [Bug 307]
mac80211 does not use this type of Michael MIC event, so this is not
really used and proper Michael MIC failure processing will be added
using an nl80211 event once that gets added into wireless-testing.git.
It looks like both new nl80211 operations (scan and auth/assoc) end up
being added in Linux 2.6.30, so we do not need to maintain the backwards
compatibility code in wpa_supplicant.
Update credential to only include a single authentication and
encryption type in case the AP configuration includes more than one
option. Without this, the credential would be rejected if the AP was
configured to allow more than one authentication type.
A new network block parameter, scan_freq, can be used to specify subset
of frequencies to scan. This can speed up scanning process considerably
if it is known that only a small subset of channels is actually used in
the network. A union of configured frequencies for all enabled network
blocks is used in scan requests.
Currently, only driver_nl80211.c has support for this functionality.
For example, following parameter marks 2.4 GHz channels 1, 6, 11 to be
scanned: scan_freq=2412 2437 2462
Move the shared IEEE 802.11w enum definition into src/common/defs.h to
avoid redefinition when both configuration structures are included into
the same file.
The memcpy was using incorrect size (of pointer; should have been of
data structure) for the client address. This ended up working on 64-bit
targets, but left part of the address uninitialized on 32-bit targets.
This version is adding the configuration option (mode=2) for this and
driver capability reporting to figure out whether AP mode can be used.
However, this does not actually implement any real functionality yet.
Need to set drv->ifindex before calling set_mode(). In addition, set the
mode before setting the interface up to avoid having to set it down
again.
Add more useful error message on mode changes.
All these driver handlers can be implemented in associate() handler
which gets all the needed information in the parameters structure. The
old functions that provided only a single parameter will be removed
eventually to clean up the driver_ops structure, so driver wrappers
should start using the newer mechanism.
This can be used, e.g., with mac80211-based Linux drivers with
nl80211. This allows over-the-air FT protocol to be used (IEEE
802.11r).
Since the nl80211 interface needed for this is very recent (added
today into wireless-testing.git), driver_nl80211.c has backwards
compatibility code that uses WEXT for association if the kernel does
not support the new commands. This compatibility code can be
disabled by defining NO_WEXT_COMPAT. That code will also be removed
at some point to clean up driver_nl80211.c.
On "eap_tnc_process" function error case, data->in_buf keeps reference
to a local scope variable. For example this will cause segmentation
fault in "eap_tnc_deinit" function "wpabuf_free(data->in_buf)"
statement.
This was broken by 510c02d4a3 which added
validation of eap_ttls_phase2_eap_init() return value. The main problem
in the code trying to initialize a new phase 2 EAP method
unconditionally; this should only happen if there is a new method in the
inner method sequence.
This is based on a patch and report by Masashi Honma
<honma@ictec.co.jp>. The issue is more generic than just TNC, though,
since failure to initialize any phase 2 EAP method can result in NULL
dereference.
On PEAP(TNC), hostapd integrated RADIUS server doesn't return
EAP-Failure when "Recommendation = none". So, EAP data retransmittion
occurs.
My co-worker "Ryuji Ohba" made below patch.
hostapd will now go through the RIC Request and process each RDIE. Only
WMM TSPEC requests are currently supported; all other request
descriptors will be declined.
RIC Response is written by hostapd and verified by wpa_supplicant (MIC
validation). wpa_supplicant does not yet have code to notify the driver
about the resource request results.
This adds first part of FT resource request as part of Reassocition
Request frame (i.e., FT Protocol, not FT Resource Request Protocol).
wpa_supplicant can generate a test resource request when driver_test.c
is used with internal MLME code and hostapd can verify the FTIE MIC
properly with the included RIC Request.
The actual RIC Request IEs are not processed yet and hostapd does not
yet reply with RIC Response (nor would wpa_supplicant be able to
validate the FTIE MIC for a frame with RIC Response).
Windows XP and Vista clients can get confused about EAP-Identity/Request
when they probe the network with EAPOL-Start. In such a case, they may
assume the network is using IEEE 802.1X and prompt user for a
certificate while the correct (non-WPS) behavior would be to ask for the
static WEP key. As a workaround, use Microsoft Provisioning IE to
advertise that legacy 802.1X is not supported.
This seems to make Windows ask for a static WEP key when adding a new
network, but at least Windows XP SP3 was still marking IEEE 802.1X
enabled for the network. Anyway, this is better than just leaving the
network configured with IEEE 802.1X and automatic WEP key distribution.
When using the internal TLS implementation, EAP-FAST unauthenticated
provisioning ends up proposing multiple cipher suites. It looks like
Cisco AP (at least 350 and 1200 series) local authentication server does
not know how to search cipher suites from the list and seem to require
that the last entry in the list is the one that it wants to use.
However, TLS specification requires the list to be in the client
preference order. As a workaround, ass anon-DH AES-128-SHA1 again at the
end of the list to allow the Cisco code to find it.
This fixed EAP-FAST provisioning with the following IOS version:
Cisco IOS Software, C350 Software (C350-K9W7-M), Version 12.3(8)JEA3,
RELEASE SOFTWARE (fc2)
Compiled Wed 21-Nov-07 14:08 by ccai
This is just there very first step on being able to do something with
wireless LAN on Vista. There is some example code for requesting a scan,
but it does not work in its current form. Anyway, this adds a wpa_printf
noting that Native 802.11 drivers are not yet supported.
This is done with wired interfaces to fix IEEE 802.1X authentication
when the authenticator uses the group address (which should be happening
with wired Ethernet authentication).
This allows wpa_supplicant to complete wired authentication successfully
on Vista with a NDIS 6 driver, but the change is likely needed for
Windows XP, too.
Do not use just the driver name for this since driver_ndis.c supports
both wired and wireless NDIS drivers and needs to indicate the driver
type after initialization.
Calculate the estimated medium time using integer variables since there
is no real need to use floating point arithmetics here. In addition,
make sure there is no division by zero regardless of how invalid the
request from the station is. Reject invalid parameters and refuse
requests that would take most of the bandwidth by themselves.
Add test code into wpa_supplicant mlme.c to allow WMM-AC negotiation to
be tested with driver_test.
The new file wps_nfc.c and ndef.c implements NFC device independent
operation, wps_nfc_pn531.c implements NFC device dependent operation.
This patch is only for the following use case:
- Enrollee = wpa_supplicant
- Registrar = hostapd internal Registrar
Following NFC methods can be used:
- Enrollee PIN with NFC
- Registrar PIN with NFC
- unencrypted credential with NFC
Encrypted credentials are not supported.
Enrollee side operation:
Registrar side operation:
Example configuration.
CONFIG_WPS=y
CONFIG_WPS_NFC=y
CONFIG_WPS_NFC_PN531=y
I used NFC device "NXP PN531". The NFC device access method is
confidential, so I used outer library. Please download below files from
https://www.saice-wpsnfc.bz/index.php
[WPS NFC Library]
WpsNfcLibrary/WpsNfc.h
WpsNfcLibrary/WpsNfcType.h
WpsNfcLibrary/WpsNfcVersion.h
WpsNfcLibrary/linux/libnfc_mapping_pn53x.dll
WpsNfcLibrary/linux/wpsnfc.dll
[NFC Reader/Writer Kernel Driver]
NFCKernelDriver-1.0.3/linux/kobj/sonyrw.ko
<WiFi test>
The hostapd/wpa_supplicant with this patch passed below tests on
"Wi-Fi WPS Test Plan Version 1.6".
4.2.5 Add device using NFC Method with password token
(I used SONY STA instead of NXP STA.)
4.2.6 Add device using NFC Method with configuration token
5.1.9 Add to AP using NFC Method with password token
through internal registrar
(I used SONY AP instead of NXP AP.)
5.1.10 Add to AP using NFC Method with configuration token
through internal registrar
This updates the terminogy to match with the final WMM specification. In
addition, some of the WMM TSPEC structure fields were in incorrect order
and used without byte order swapping. Those are also taken care of this
cleanup patch.
The EAP server state machine will need to have special code in
getDecision() to avoid starting passthrough operations before having
completed Identity round in the beginning of reauthentication. This was
broken when moving into using the full authenticator state machine from
RFC 4137 in 0.6.x.
The old behavior of generating new DH keys can be maintained for non-OOB
cases and only OOB (in this case, with UFD) will use the pre-configured
DH keys to allow the public key hash to be checked.
Not all embedded devices have USB interface and it is useful to be able
to remove unneeded functionality from the binary. In addition, the
current implementation has some UNIX specific calls in it which may make
it not compile cleanly on all target systems.
Reduce startWhen from 3 to 1 second if WPS is included in the build.
While this is done regardless of runtime WPS configuration, it is fine
to use a smaller value here in general. This cuts two seconds out from
WPS negotiation if the driver does not support addition of WPS IE into
the (Re)Association Request frame.
Previously, both CONFIG_IEEE80211W=y and CONFIG_IEEE80211R=y were needed
to enable SHA256-based key handshake (WPA-PSK-SHA256 and
WPA-EAP-SHA256). This can now be done with just CONFIG_IEEE80211W=y.
These flags are used to mark which values (level, noise, qual) are
invalid (not available from the driver) and whether level is using dBm.
D-Bus interface will now only report the values that were available.
If session resumption fails for any reason, do not try it again because
that is just likely to fail. Instead, drop back to using full
authentication which may work. This is a workaround for servers that do
not like session resumption, but do not know how to fall back to full
authentication properly.
This fixes an issue where two AKA'/Challenge messages are received when
resynchronizing SEQ#. Previously, this used to trigger an authentication
failure since the second Challenge message did not duplicate AT_KDF.
This does not actually send out separate scan requests for each SSID,
but the debug output can be used to test scan2() functionality with
multiple SSIDs.
This can be used to provide support for scanning multiple SSIDs at a
time to optimize scan_ssid=1 operations. In addition, Probe Request IEs
will be available to scan2() (e.g., for WPS PBC scanning).
For example, -Dnl80211,wext could be used to automatically select
between nl80211 and wext. The first driver wrapper that is able to
initialize the interface will be used.
This workaround was needed with some drivers that used WEXT, but there
is no known nl80211-enabled driver that would need this, so lets get rid
of the extra delay.
The driver wrappers can now inform wpa_supplicant how many SSIDs can
be used in a single scan request (i.e., send multiple Probe Requests
per channel). This value is not yet used, but it can eventually be used
to allow a new scan command to specify multiple SSIDs to speed up
scan_ssid=1 operations. In addition, a warning could be printed if
scan_ssid=1 is used with a driver that does not support it
(max_scan_ssids=0).
Some drivers (for example ipw2100) do not report signal level but only
signal quality. wpa_supplicant already uses the signal quality if no
level is reported and all other comparision parameters are equal to sort
the scan results. However, if two APs have different max rates and the
signal level does not differ much wpa_supplicant chooses the AP with the
higher max rate.
In case of ipw2100 no signal level is reported and thus wpa_supplicant
always takes the AP with higher max rate even if its signal quality is
really low. For example if AP1 (max rate 11Mb/s, 80% signal quality) and
AP2 (max rate 54 Mb/s, 20% signal quality) are found by a scan
wpa_supplicant would choose AP2.
Hence, if no signal level is reported depend on the signal quality if
max rate should be compared. A quality difference of 10% is considered
acceptable in favor of the higher max rate.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Really disassociate when tearing stuff down; drivers may sometimes
(legally) keep trying to reassociate unless the BSSID is unlocked. If
the SSID is unlocked too, under WEXT drivers are able to pick an SSID to
associate, so kill that behavior by setting a bogus SSID. Unfortunately
WEXT doesn't provide an easy method to say "stop whatever doing and just
idle".
Signed-off-by: Dan Williams <dcbw@redhat.com>
It looks like GnuTLS (at least newer versions) is using random padding
on the application data and the previously used 100 byte extra buffer
for tls_connection_encrypt() calls was not enough to handle all cases.
This resulted in semi-random authentication failures with EAP-PEAP and
EAP-TTLS during Phase 2.
Increase the extra space for encryption from 100 to 300 bytes and add an
error message into tls_gnutls.c to make it easier to notice this issue
should it ever show up again even with the larger buffer.
I tried PBC with the hostapd registrar.
I pushed the button with "hostap_cli WPS_PBC".
But hostapd registrar always sends Selected Registrar Config Methods
attribute=0x0000 in beacon/probe response.
Allow more than one pending PutWLANMessage data to be stored (M2/M2D
from multiple external Registrars) and drop pending M2/M2D messages when
the Enrollee replies with M3.
Version attribute processing details are not described in the WPS spec,
but it is safer to allow minor version to change and only refuse to
process the message if major version is different from ours. This
matches with the behavior used in the Intel reference implementation.
It looks like we don't set correspondent Device Password ID attribute in
M2 message during PBC registration. Without it TG185n STA was not able
to connect to our AP in PBC mode. Attached patch fixes this.
The madwifi driver has interface to set probe request ie.
Attached patch will enable the functionality.
I could see probe request includes WSC IE with this patch.
We can now handle up to 65535 byte result buffer which is the maximum
due to WEXT using 16-bit length field. Previously, this was limited to
32768 bytes in practice even through we tried with 65536 and 131072
buffers which we just truncated into 0 in the 16-bit variable.
This more or less doubles the number of BSSes we can received from scan
results.
I am terribly sorry, but because of a lack of testing equipment the
patch was submitted not properly tested.
Because the chipset documentation is not publicly available all
behaviour has to be found out by experimentation. The other day, I
made some incorrect assumptions based on my findings.
I do believe the attached patch does support the whole RoboSwitch line
(5325, 5350, 5352, 5365 and others). It is a drop-in substitution for
my previous submission.
The RoboSwitch driver of wpa_supplicant had one shortcoming: not
supporting the 5365 series. I believe the patch attached fixes this
problem.
Furthermore it contains a small readability rewrite. It basically is an
explicit loop-rollout so that the wpa_driver_roboswitch_leave style
matches that of wpa_driver_roboswitch_join.
If the bind() on /tmp/wpa_ctrl_<pid>_<in-proc-counter> fails with
EADDRINUSE, there is an existing socket file with the name we are trying
to create. Since getpid() is unique, there cannot be another process
using that socket and we can just unlink the file and try again. This
can speed up client connection if wpa_cli is killed without allowing it
to clean up the socket file. [Bug 288]
This adds mostly feature complete external Registrar support with the
main missing part being proper support for multiple external Registrars
working at the same time and processing of concurrent registrations when
using an external Registrar.
This code is based on Sony/Saice implementation
(https://www.saice-wpsnfc.bz/) and the changes made by Ted Merrill
(Atheros) to make it more suitable for hostapd design and embedded
systems. Some of the UPnP code is based on Intel's libupnp. Copyrights
and licensing are explained in src/wps/wps_upnp.c in more detail.
We must not replace M1 with M2D as the last_msg since we need M1 to
validate a possible M2 after M2D. Since M2D and ACK/NACK replies do not
include Authenticator attribute, we can just ignore M2D as far as
updating last_msg is concerned.
External Registrar in Vista may include NULL termination in the Network
Key when encoding an ASCII passphrase for WPA/WPA2-PSK. As a workaround,
remove this extra octet if present.
If a Registrar tries to configure the AP, but fails to validate the
device password (AP PIN), lock the AP setup after four failures. This
protects the AP PIN against brute force guessing attacks.
This optional configuration parameter can be used to override AP
Settings attributes in M7 similarly to extra_cred option for Credential
attribute(s) in M8.
Buffalo WHR-G125 Ver.1.47 seems to send EAP-WPS packets with too short
EAPOL header length field (14 octets regardless of EAP frame length).
This is fixed in firmware Ver.1.49, but the broken version is included
in many deployed APs. As a workaround, fix the EAPOL header based on the
correct length in the EAP packet. This workaround can be disabled with
eap_workaround=0 option in the network configuration.
Some WPS APs do not set Selected Registrar attribute to 1 properly when
using an external Registrar. Allow such an AP to be selected for PIN
registration after couple of scan runs that do not find APs marked with
Selected Registrar = 1. This allows wpa_supplicant to iterate through
all APs that advertise WPS support without delaying connection with
implementations that set Selected Registrar = 1 properly.
WPS spec is not very specific on the presentation used for the DH
values. The Public Key attribute is described to be 192 octets long, so
that could be interpreted to imply that other places use fixed length
presentation for the DH keys. Change the DH derivation to use fixed
length bufferd by zero padding them from beginning if needed. This can
resolve infrequent (about 1/256 chance for both Public Key and Shared
Key being shorter) interop issues.
This is needed to allow external Registrar (at least the implementation
in Windows Vista) to configure the Enrollee.
With this patch and my previous patch (for wps.c) , I could pass "Wi-Fi
WPS Test Plan Version 1.0 [5.1.4. Add to AP using PIN Config method and
PASS PHRASE through wired external registrar]".
I can't pass the "Wi-Fi WPS Test Plan Version 1.0 [5.1.4. Add to AP
using PIN Config method and PASS PHRASE through wired external
registrar]". The wpa_supplicant-0.6.7 can't recoginize the testbed
AP(BCM94704AGRRev-E.2.4) as WPS PIN AP. Because after PIN entered, the
AP sends Selected Registrar attribute=0 and not send Device Password ID
attribute.
The proposed change as-is removed validation of Selected Registrar
attribute completely. However, that part is not included in this commit
since it can cause problems for environments with multiple WPS-enabled
APs. Another workaround for this will be considered in wpa_supplicant
scanning process (e.g., start trying to use WPS with APs that do not set
Selected Registrar to TRUE after couple of scan runs that do not find
any APs with Selected Registrar TRUE).
This operation can now be moved into an external program by configuring
hostapd with wps_cred_processing=1 and skip_cred_build=1. A new
ctrl_iface message (WPS-REG-SUCCESS <Enrollee MAC addr> <UUID-E>) will
be used to notify external programs of each successful registration and
that can be used as a tricker to move from unconfigured to configured
state.
The separate Association Comeback Time IE was removed from IEEE 802.11w
and the Timeout Interval IE (from IEEE 802.11r) is used instead. The
editing on this is still somewhat incomplete in IEEE 802.11w/D7.0, but
still, the use of Timeout Interval IE is the expected mechanism.
This makes it easier to pass the credential data to external programs
(e.g., Network Manager) for processing. The actual use of this data is
not yet included in hostapd/wpa_supplicant.
This commit adds a new build option, CONFIG_IBSS_RSN=y, that can be used
to enable RSN support for IBSS. This links in RSN Authenticator code
from hostapd and adds code for managing per-peer information for IBSS. A
new wpa_cli command or driver event can be used to request RSN
authentication with an IBSS peer. New RSN Authenticator and Supplicant
will be allocated for each peer.
The basic state machine setup code is included in this commit, but the
state machines are not properly started yet. In addition, some of the
callback functions are not yet complete.
This is needed for airo driver to work correctly and no other driver
seems to care, so the change is safe to make. This has been in number of
distro releases for a long time and no issues have been reported.
The configuration parsing functions seemed to have worked fine before,
but these were real bugs even if they did not show up in practice.
hostapd_ip_diff() was broken for IPv6 addresses (overwrote address and
always returned 1.
Generate a SHA1 hash -based UUID from the local MAC address if the UUID
was not configured. This makes it easier to prepare for WPS since there
is no need to generate an UUID.
IEEE 802.11w/D7.0 incorrectly changed the Action Category from 8 to 7
when renaming Ping to SA Query. Category 7 is reserved for HT (IEEE
802.11n) and IEEE 802.11w will need to continue to use the category 8
that was allocated for it.
Previous version assumed that the Flags field is always present and
ended up reading one octet past the end of the buffer should the Flags
field be missing. The message length would also be set incorrectly
(size_t)-1 or (size_t)-5, but it looks like reassembly code ended up
failing in malloc before actually using this huge length to read data.
RFC 2716 uses a somewhat unclear description on what exactly is included
in the TLS Ack message ("no data" can refer to either Data field in 4.1
or TLS Data field in 4.2), so in theory, it would be possible for some
implementations to not include Flags field. However,
EAP-{PEAP,TTLS,FAST} need the Flags field in Ack messages, too, for
indicating the used version.
The EAP peer code will now accept the no-Flags case as an Ack message if
EAP workarounds are enabled (which is the default behavior). If
workarounds are disabled, the message without Flags field will be
rejected.
[Bug 292]
It looks like this never survived the move from IEEE 802.1X-2001 to
IEEE 802.1X-2004 and EAP state machine (RFC 4137). The retransmission
scheduling and control is now in EAP authenticator and the
calculateTimeout() producedure is used to determine timeout for
retransmission (either dynamic backoff or value from EAP method hint).
The recommended calculations based on SRTT and RTTVAR (RFC 2988) are not
yet implemented since there is no round-trip time measurement available
yet.
This should make EAP authentication much more robust in environments
where initial packets are lost for any reason. If the EAP method does
not provide a hint on timeout, default schedule of 3, 6, 12, 20, 20, 20,
... seconds will be used.
Previously, only the delivery option 1 from RFC 4284
(EAP-Request/Identity from the AP) was supported. Now option 3
(subsequent EAP-Request/Identity from RADIUS server) can also be used
when hostapd is used as a RADIUS server. The eap_user file will need to
have a Phase 1 user entry pointing to Identity method in order for this
to happen (e.g., "* Identity" in the end of the file). The identity hint
is configured in the same was as for AP/Authenticator case (eap_message
in hostapd.conf).
This commit changes just the name and Action category per D7.0. The
retransmit/timeout processing in the AP is not yet updated with the
changes in D7.0.
Some deployed WPS implementations fail to parse zero-length attributes.
As a workaround, send a null character if the device attribute string is
empty. This allows default values (empty strings) to be used without
interop issues.
Before this change, it looked like an AP that was using wsccmd did not
get activated since wsccmd left the Selected Registrar Config Methods
attribute to be zero. Since Device Password ID can be used to
distinguish PBC from any other method, use only it to figure out whether
PBC or PIN method is active.
The new INTERFACE_LIST global control interface command can be used to
request a list of all available network interfaces that could be used
with the enabled driver wrappers. This could be used to enable
interfaces automatically by external programs (e.g., wpa_gui).
Driver wrappers can now register global_init() and global_deinit()
driver_ops handlers to get a global data structure that can be shared
for all interfaces. This allows driver wrappers to initialize some
functionality (e.g., interface monitoring) before any interfaces have
been initialized.
This callback is now used to stop wpa_supplicant from trying to continue
using parameters (most likely, device password) that do not work in a
loop. In addition, wpa_gui can now notify user of failed registration.
The event callback will be used for various event messages and the M2D
notification is the first such message. It is used to notify wpa_gui
about Registrar not yet knowing the device password (PIN).
We need to be a bit more careful when removing the WPS configuration
block since wpa_s->current_ssid may still be pointing at it. In
addition, registrar pointer in wps_context will need to be cleared
since the context data is now maintained over multiple EAP-WSC runs.
Without this, certain WPS operations could have used freed memory.
Instead of sending out EAP-Failure on errors (on AP) or stopping (on
Supplicant), send a NACK message based on the allowed EAP state machine
transitions for EAP-WSC.
Whenever new scan results include WPS AP(s) and the client is not
associated, send a notification message to control interface monitors.
This makes it easier for GUIs to notify the user about possible WPS
availability without having to go through the scan results.
Windows Server 2008 NPS gets very confused if the TLS Message Length is
not included in the Phase 1 messages even if fragmentation is not used.
If the TLS Message Length field is not included in ClientHello message,
NPS seems to decide to use the ClientHello data (excluding first six
octets, i.e., EAP header, type, Flags) as the OuterTLVs data in
Cryptobinding Compound_MAC calculation (per PEAPv2; not MS-PEAP)..
Lets add the TLS Message Length to PEAPv0 Phase 1 messages to get rid of
this issue. This seems to fix Cryptobinding issues with NPS and PEAPv0
is now using optional Cryptobinding by default (again) since there are
no known interop issues with it anymore.
Changed peer to derive the full key (both MS-MPPE-Recv-Key and
MS-MPPE-Send-Key for total of 32 octets) to match with server
implementation.
Swapped the order of MPPE keys in MSK derivation since server
MS-MPPE-Recv-Key | MS-MPPE-Send-Key matches with the order specified for
EAP-TLS MSK derivation. This means that PEAPv0 cryptobinding is now
using EAP-MSCHAPv2 MSK as-is for ISK while EAP-FAST will need to swap
the order of the MPPE keys to get ISK in a way that interoperates with
Cisco EAP-FAST implementation.
driver_test can now be used either over UNIX domain socket or UDP
socket. This makes it possible to run the test over network and makes it
easier to port driver_test to Windows.
hostapd configuration: test_socket=UDP:<listen port>
wpa_supplicant configuration: driver_param=test_udp=<dst IP addr>:<port>
This adds support for setting of a regulatory domain to wpa_supplicant
drivers. It also adds regulatory domain setting for the nl80211 driver.
We expect an ISO / IEC 3166 alpha2 in the wpa configuration file as a
global.
Since only one KDF is currently supported, the negotiation is not
allowed and peer must be rejected if it tries to send KDF selection in a
Challenge message. The negotiation code is left in the file and just
commented out since it was tested to work and can be used in the future
if another KDF is added.
The attribute uses 'Actual Identity Length' field to indicate the exact
(pre-padding) length of the Identity. This actual length should be used
as the length, not the remaining attribute length.
This was previously worked around by stripping null termination away
from the end of the identity string at EAP-SIM and EAP-AKA server code.
However, it is likely that that workaround is not really needed and the
real problem was in AT_IDENTITY parsing. Anyway, the workaround is left
in just in case it was really needed with some implementations.
This IE is not (at least yet) actually used for anything, but parsing it
cleans up verbose debug log a bit since thie previously unknown, but
commonly used, vendor IE was being reported as unknown.
This allows the same source code file to be shared for both methods. For
now, this is only in eap_aka_prime.c, but eventually, changes in
eap_aka_prime.c are likely to be merged into eap_aka.c at which point
the separate eap_aka_prime.c can be removed.
This is just making an as-is copy of EAP-AKA server and peer
implementation into a new file and by using the different EAP method
type that is allocated for EAP-AKA' (50). None of the other differences
between EAP-AKA and EAP-AKA' are not yet included.
It is likely that once EAP-AKA' implementation is done and is found to
work correctly, large part of the EAP-AKA and EAP-AKA' code will be
shared. However, it is not reasonable to destabilize EAP-AKA
implementation at this point before it is clearer what the final
differences will be.
Since the Registrar may not yet know the UUID-E when a new PIN is
entered, use of a wildcard PIN that works with any UUID-E can be useful.
Such a PIN will be bound to the first Enrollee trying to use it and it
will be invalidated after the first use.
Fragment WPS IE if needed to fit into the IE length limits in hostapd
and Reassemble WPS IE data from multiple IEs in wpa_supplicant.
In addition, moved WPS code from events.c into wps_supplicant.c to clean
up module interfaces.
These functions fit in better with the category of functions included in
wps.c. wps_common.c is now used for generic helper functions (currently,
only crypto code).
WPS IE is now passed from hostapd association processing into EAP-WSC
and WPS processing. Request Type attribute is parsed from this
information and if the request is for a WLAN Manager Registrar,
additional management keys are derived (to be used with UPnP).
The wps_context data is now managed at wpa_supplicant, not EAP-WSC. This
makes wpa_supplicant design for WPS match with hostapd one and also
makes it easier configure whatever parameters and callbacks are needed
for WPS.
Previously, wpa_supplicant as Enrollee case was handled using a
different callback function pointer. However, now that the wps_context
structure is allocated for all cases, the same variable can be used in
all cases.
Previously, hardcoded values were used in wps_enrollee.c. These are now
moved into shared data in struct wps_context. In case of
AP/Authenticator, these are initialized in wps_hostapd.c. In case of
client/supplicant, these are now initialized in EAP-WSC peer method,
but will probably end up being moved into higher layer for better
configuration.
EAP-WSC peer method for
This allows the network to be used after the Registrar configuration
step. The local WPS network is replaced with a new network block
similarly to the case of acting as an Enrollee.
This makes it easier to store old AP settings into wps->cred (and allow
them to modified and taken into use in the future). Separation between
Credential and AP Settings building is also cleaner in this design.
The old (i.e., currently used) AP Settings are processed. For now, they
are copied as-is into M8 as new AP Settings to avoid changing
configuration. This should be changed to allow external programs (e.g.,
GUI) to fetch the old AP settings over ctrl_iface and then allow
settings to be changed before sending M8 with the new settings.
The core processing of attributes into struct wps_credential is now in
wps_common.c (was in wps_enrollee.c), so that the same code can be
shared with Registrar.
This adds WPS support for both hostapd and wpa_supplicant. Both programs
can be configured to act as WPS Enrollee and Registrar. Both PBC and PIN
methods are supported.
Currently, hostapd has more complete configuration option for WPS
parameters and wpa_supplicant configuration style will likely change in
the future. External Registrars are not yet supported in hostapd or
wpa_supplicant. While wpa_supplicant has initial support for acting as
an Registrar to configure an AP, this is still using number of hardcoded
parameters which will need to be made configurable for proper operation.
It looks like some Windows NDIS drivers (e.g., Intel) do not clear the
PMKID list even when wpa_supplicant explicitly sets the list to be
empty. In such a case, the driver ends up trying to use PMKSA caching
with the AP and wpa_supplicant may not have the PMK that would be needed
to complete 4-way handshake.
RSN processing already had some code for aborting PMKSA caching by
sending EAPOL-Start. However, this was not triggered in this particular
case where the driver generates the RSN IE. With this change, this case
is included, too, and the failed PMKSA caching attempt is cleanly
canceled and wpa_supplicant can fall back to full EAP authentication.
It the message was large enough to require fragmentation (e.g., if a large
Session Ticket data is included), More Fragment flag was set, but no
more fragments were actually sent (i.e., Access-Accept was sent out).
It looks like [MS-PEAP] 3.2.5.6 points towards this being the expected
behavior (however, that chapter is very confusing).
In addition, remove Cryptobinding TLV from response if the received
Cryptobinding TLV is not valid. Add some more debug messages to the case
where the received Cryptobinding TLV is found invalid.
I fixed the engine issue in phase2 of EAP-TTLS. The problem was that you
only defined one engine variable, which was read already in phase1. I
defined some new variables:
engine2
engine2_id
pin2
and added support to read those in phase2 wheres all the engine
variables without number are only read in phase1. That solved it and I
am now able to use an engine also in EAP-TTLS phase2.
Find attached the patch that creates a new driver: roboswitch. This
driver adds support for wired authentication with a Broadcom
RoboSwitch chipset. For example it is now possible to do wired
authentication with a Linksys WRT54G router running OpenWRT.
LIMITATIONS
- At the moment the driver does not support the BCM5365 series (though
adding it requires just some register tweaks).
- The driver is also limited to Linux (this is a far more technical
restriction).
- In order to compile against a 2.4 series you need to edit
include/linux/mii.h and change all references to "u16" in "__u16". I
have submitted a patch upstream that will fix this in a future version
of the 2.4 kernel. [These modifications (and more) are now included in
the kernel source and can be found in versions 2.4.37-rc2 and up.]
USAGE
- Usage is similar to the wired driver. Choose the interfacename of
the vlan that contains your desired authentication port on the router.
This name must be formatted as <interface>.<vlan>, which is the
default on all systems I know.
Remove the old code from driver_wext.c since the private ioctl interface is
never going to be used with mac80211. driver_nl80211.c has an
implementation than can be used with mac80211 (with two external patches to
enable userspace MLME configuration are still required, though).
Updated OpenSSL code for EAP-FAST to use an updated version of the
session ticket overriding API that was included into the upstream
OpenSSL 0.9.9 tree on 2008-11-15 (no additional OpenSSL patch is
needed with that version anymore).
It looks like ACS did not like PAC Acknowledgment TLV before Result TLV, so
reorder the TLVs to match the order shown in a
draft-cam-winget-eap-fast-provisioning-09.txt example. This allows
authenticated provisioning to be terminated with Access-Accept (if ACS has
that option enabled). Previously, provisioning was otherwise successful,
but the server rejected connection due to not understanding the PAC Ack
("Invalid TEAP Data recieved").
Previously, hardcoded identity in the network configuration skipped both
IMSI reading and PIN verification. This broke cases where PIN is needed for
GSM/UMTS authentication. Now, only IMSI reading is skipped if identity is
hardcoded.
This change breaks interoperability with older wpa_supplicant versions
(everything up to and including wpa_supplicant 0.5.10 and 0.6.5) which
incorrectly used this field as number of bytes, not bits, in RES.
Instead of falling back to full TLS handshake on expired PAC, allow the
PAC to be used to allow a PAC update with some level of server
authentication (i.e., do not fall back to full TLS handshake since we
cannot be sure that the peer would be able to validate server certificate
now). However, reject the authentication since the PAC was not valid
anymore. Peer can connect again with the newly provisioned PAC after this.
Added a new configuration option, wpa_ptk_rekey, that can be used to
enforce frequent PTK rekeying, e.g., to mitigate some attacks against TKIP
deficiencies. This can be set either by the Authenticator (to initiate
periodic 4-way handshake to rekey PTK) or by the Supplicant (to request
Authenticator to rekey PTK).
With both wpa_ptk_rekey and wpa_group_rekey (in hostapd) set to 600, TKIP
keys will not be used for more than 10 minutes which may make some attacks
against TKIP more difficult to implement.
A driver was found to remove SSID IE from NDIS_WLAN_BSSID_EX IEs, but the
correct SSID is included in NDIS_802_11_SSID structure inside the BSSID
data. If this is seen in scan results, create a matching SSID IE and add it
to the end of IEs to fix scan result parsing.
Need to make sure that portValid is TRUE in order to avoid PAE state
machine going into DISCONNECTED state on eapol_sm_step(). This could be
triggered at least with OKC.
Changed EAP-FAST configuration to use separate fields for A-ID and
A-ID-Info (eap_fast_a_id_info) to allow A-ID to be set to a fixed
16-octet len binary value for better interoperability with some peer
implementations; eap_fast_a_id is now configured as a hex string.
eap_fast_prov config parameter can now be used to enable/disable different
EAP-FAST provisioning modes:
0 = provisioning disabled
1 = only anonymous provisioning allowed
2 = only authenticated provisioning allowed
3 = both provisioning modes allowed
draft-cam-winget-eap-fast-provisioning-06.txt or RFC 4851 do not seem to
mandate any particular order for TLVs, but some interop issues were noticed
with an EAP-FAST peer implementation when Result TLV followed PAC TLV. The
example in draft-cam-winget-eap-fast-provisioning-06.txt shows the TLVs in
the other order, so change the order here, too, to make it less likely to
hit this type of interop issues.
This adds all the attributes that are marked as mandatory for SoH in
IF-TNCCS-SOH v1.0. MS-Machine-Inventory does not contain correct data
(i.e., all version fields are just marked as inapplicable) and
MS-MachineName is hardcoded to wpa_supplicant@w1.fi for now.
It is possible that the initialization of the Phase 2 EAP method fails and
if that happens, we need to stop EAP-TTLS server from trying to continue
using the uninitialized EAP method. Otherwise, the server could trigger
a segmentation fault when dereferencing a NULL pointer.
A bug just got reported as a result of this for mac80211 drivers.
https://bugzilla.redhat.com/show_bug.cgi?id=459399
The basic problem is that since taking the device down clears the keys
from the driver on many mac80211-based cards, and since the mode gets
set _after_ the keys have been set in the driver, the keys get cleared
on a mode switch and the resulting association is wrong. The report is
about ad-hoc mode specifically, but this could happen when switching
from adhoc back to managed mode.
IEEE 802.11w/D6.0 defines new AKMPs to indicate SHA256-based algorithms for
key derivation (and AES-CMAC for EAPOL-Key MIC). Add support for using new
AKMPs and clean up AKMP processing with helper functions in defs.h.
This updates management frame protection to use the assocition ping process
from the latest draft (D6.0) to protect against unauthenticated
authenticate or (re)associate frames dropping association.
This adds most of the new frame format and identifier definitions from IEEE
802.11w/D6.0. In addition, the RSN IE capability field values for MFP is
replaced with the new two-bit version with MFPC (capable) and MFPR
(required) processing.
If IWEVGENIE or custom event wpa_ie/rsn_ie is received in scan with empty
buffer, the previous version ended up calling realloc(NULL, 0) which seems
to return a non-NULL value in some cases. When this return value is passed
again into realloc with realloc(ptr, 0), the returned value could be NULL.
If the ptr is then freed (os_free(data.ie) in SIOCGIWAP handling), glibc
may crash due to invalid pointer being freed (or double-freed?). The
non-NULL realloc(NULL, 0) return value from glibc looks a bit odd behavior,
but anyway, better avoid this case completely and just skip the IE events
that have an empty buffer.
This issue should not show up with drivers that produce proper scan results
since the IEs will always include the two-octet header. However, it seems
to be possible to see this when using 64-bit kernel and 32-bit userspace
with incorrect compat-ioctl processing.
When the TLS handshake had been completed earlier by the server in case of
abbreviated handshake, the output buffer length was left uninitialized. It
must be initialized to zero in this case. This code is used by EAP-FAST
server and the uninitialized length could have caused it to try to send a
very large frame (though, this would be terminated by the 50 roundtrip EAP
limit). This broke EAP-FAST server code in some cases when PAC was used to
establish the tunnel.
This commit brings in cleaned up version of IEEE 802.11n implementation
from Intel (1). The Intel tarball includes number of other changes, too,
and only the changes specific to IEEE 802.11n are brought in here. In
addition, this does not include all the changes (e.g., some of the
configuration parameters are still missing and driver wrapper changes for
mac80211 were not included).
(1)
http://www.kernel.org/pub/linux/kernel/people/chuyee/wireless/iwl4965_ap/hostap_0_6_0_intel_0.0.13.1.tgz
These functions are based on the hostapd implementation and complete
the userspace MLME code in wpa_supplicant (though, mac80211 will still need
couple of pending patches to be integrated in order to get userspace client
MLME working again).
This adds some parts needed to use usermode MLME with the current mac80211
(plus a patch to add a new cfg80211 command; not yet submitted to
wireless-testing). This version creates a monitor interface for management
frames and is able to send Probe Request frames during scan. However, it
looks like management frame reception is not yet working properly. In
addition, mlme_{add,remove}_sta() handlers are still missing.
Network device ifindex will change when the interface is re-inserted.
driver_nl80211.c will need to accept netlink events from "unknown" (based
on ifindex) interfaces when a previously used card was removed earlier. If
the previously removed interface is added back, the driver_wext data need
to be updated to match with the new ifindex value. In addition, the initial
setup tasks for the card (set interface up, update ifindex, set mode, etc.)
from wpa_driver_nl80211_init() need to be run again.
This is the changes from commit 3fbda8f943
(driver_wext.c) ported for driver_nl80211.c.
wpa_sm_set_config() can be called even if the network block does not
change. However, the previous version ended up calling
pmksa_cache_notify_reconfig() every time and this cleared the network
context from PMKSA cache entries. This prevented OKC from ever being used.
Do not call pmksa_cache_notify_reconfig() if the network context remains
unchanged to allow OKC to be used.
Network device ifindex will change when the interface is re-inserted.
driver_wext.c will need to accept netlink events from "unknown" (based on
ifindex) interfaces when a previously used card was removed earlier. If the
previously removed interface is added back, the driver_wext data need to be
updated to match with the new ifindex value. In addition, the initial setup
tasks for the card (set interface up, update ifindex, set mode, etc.) from
wpa_driver_wext_init() need to be run again.
The change to support fragmentation added extra function to generate the
EAP header, but forgot to remove the original code and ended up getting two
EAP headers and TNC flags field in the generated message. These header
fields need to be added only in the function that builds the final message
(and if necessary, fragments the data).
When scan results got moved from wpa_scan_result -> wpa_scan_res, the
'maxrate' member was dropped from wpa_scan_res. The D-Bus interface
used 'maxrate', which was replaced with wpa_scan_get_max_rate().
Unfortunately, wpa_scan_get_max_rate() returns 802.11 rate values
directly from the IE, where 'maxrate' was the rate in bits/second. The
supplicant internally fakes an IE for wpa_scan_res from the value of
wpa_scan_result->maxrate, but interprets ->maxrate as an 802.11 rate
index.
As a side-effect, this fixes a soft-break of the D-Bus control API since
the wpa_scan_res change was introduced.
Function 'wpa_sm_set_config' used the argument 'config' as the network
context which is a pointer to a local variable of the function
'wpa_supplicant_rsn_supp_set_config'.
This is one reason why no proactive key was generated. This network
context never matched with the network context saved in the pmksa cache
entries.
The structure 'rsn_supp_config' has already a member 'network_ctx' which
is now filled in by this patch with 'ssid'.
Signed-off-by: Michael Bernhard <michael.bernhard@bfh.ch>
Just in case, do not use the not-yet-approved WEXT changes even if someone
where to build wpa_supplicant with IEEE 802.11w support unless this new
macro has been defined explicitly.
Added configuration of MFP related parameters with WEXT. The changes to
linux/wireless.h have not yet been applied to the Linux kernel tree, so the
code using them is still open to changes and is ifdef'ed out if
CONFIG_IEEE80211W is not set.
Add the support for the Linux wireless drivers which want to do
4-way handshake and need to know the PSK before the handshake.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Add the new flags which are supposed to be included in Linux 2.6.27
for the drivers which want to do 4-way handshake and to know PMK.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
This avoids getting stuck in state where wpa_supplicant has canceled scans,
but the driver is actually in disassociated state. The previously used code
that controlled scan timeout from WPA module is not really needed anymore
(and has not been needed for past four years since authentication timeout
was separated from scan request timeout), so this can simply be removed to
resolved the race condition. As an extra bonus, this simplifies the
interface to WPA module.
[Bug 261]
driver_nl80211.c is based on driver_wext.c and it is still using Linux
wireless extensions for many functions. Over time, the new driver interface
code should be modified to use nl80211/cfg80211 for everything.
Don't cast pointers to int in definitions of PRISM2_HOSTAPD_RID_HDR_LEN
and PRISM2_HOSTAPD_GENERIC_ELEMENT_HDR_LEN. Use size_t instead. That's
actually what the code needs.
CONFIG_INTERNAL_LIBTOMMATH_FAST=y in .config can now be used to enable all
optimized routines at a cost of about 4 kB. This is small enough increase
in size to justify simplified configuration.
At the cost of about 1 kB of additional binary size, the internal
LibTomMath can be configured to include faster div routine to speed up DH
and RSA. This can be enabled with CONFIG_INTERNAL_LIBTOMMATH_FAST_DIV=y in
.config.
This gets rid of potential warnings about buffer bounds errors. The earlier
code works fine, but it is not the cleanest way of using the struct wpa_ptk
definition for TK1/TK2.
At the cost of about 0.5 kB of additional binary size, the internal
LibTomMath can be configured to include faster sqr routine to speed up DH
and RSA. This can be enabled with CONFIG_INTERNAL_LIBTOMMATH_FAST_SQR=y in
.config.
struct wpa_ie_hdr had separate fields for 24-bit OUI and 8-bit oui_type
for WPA/RSN selectors. {WPA,RSN}_SELECTOR_{GET,PUT} access these four
octets through oui and the "out-of-bounds" access for the fourth octet is
actually reading/writing oui_type. This works fine, but some tools complain
about the array bounds "failure". Since oui_type is never accessed
separately, the simplest fix is to just combine these into a single 4-octet
field.
Since mac80211 requires that the device be !IFF_UP to change the mode
(and I think the old prism54 fullmac driver does too), do that. This
shouldn't harm fullmac devices since they can handle mode switches on
the fly and usually don't care about up/down that much.
Add a cost of about 2.5 kB of additional cost, the internal LibTomMath can
be configured to include fast exptmod routine to speed up DH and RSA.
This can be enabled with CONFIG_INTERNAL_LIBTOMMATH_FAST_EXPTMOD=y in
.config.
In situations where the driver does background scanning and sends a
steady stream of scan results, wpa_supplicant would continually
reschedule the scan. This resulted in specific SSID scans never
happening for a hidden AP, and the supplicant never connecting to the AP
because it never got found. Instead, if there's an already scheduled
scan, and a request comes in to reschedule it, and there are enabled
scan_ssid=1 network blocks, let the scan happen anyway so the hidden
SSID has a chance to be found.
mac80211 sends _both_ channel and frequency in it's scan results, with
frequency first and channel second (it's since been fixed to send
channel first and frequency second to work around this issue). This
results in wpa_supplicant getting the right value when the frequency
comes, but overwriting the value with '0' when the channel comes because
wpa_supplicant can't handle 5GHz channel numbers. So if a valid
previous SIOCGIWFREQ event came in, don't try to overwrite it.
The internal TLS implementation can now use both PKCS #1 RSA private key
and PKCS #8 encapsulated RSA private key. PKCS #8 encrypted private key is
not yet supported.
The server handshake processing was still using SSL_read() to get OpenSSL
to perform the handshake. While this works for most cases, it caused some
issues for re-authentication. This is now changed to use SSL_accept() which
is more approriate here since we know that the handshake is still going on
and there will not be any tunneled data available. This resolves some of
the re-authentication issues and makes it possible for the server to notice
if TLS processing fails (SSL_read() did not return an error in many of
these cases while SSL_accept() does).
Set session id context to a unique value in order to avoid fatal errors
when client tries session resumption (SSL_set_session_id_context() must be
called for that to work), but disable session resumption with the unique
value for the time being since not all server side code is ready for it yet
(e.g., EAP-TTLS needs special Phase 2 processing when using abbreviated
handshake).
Changed EAP-TLS server not to call TLS library when processing the final
ACK (empty data) from the client in order to avoid starting a new TLS
handshake with SSL_accept().
Move the basic processing of received frames into eap_tls_common.c and use
callback functions to handle EAP type specific processing of the version
field and payload.
Fragmentation is now done as a separate step to clean up the design and to
allow the same code to be used in both Phase 1 and Phase 2. This adds
support for fragmenting EAP-PEAP/TTLS/FAST Phase 2 (tunneled) data.
Need to clear the state back to MSG after having processed all incoming
fragments. Without this, the server got stuck in sending the fragment ACK
even after having received the full message.
Even though we try to disable TLS compression, it is possible that this
cannot be done with all TLS libraries. For example, OpenSSL 0.9.8 does not
seem to have a configuration item for disabling all compression (0.9.9 has
such an option). If compression is used, Phase 2 decryption may end up
producing more data than the input buffer due to compressed data. This
shows up especially with EAP-TNC that uses very compressible data format.
As a workaround, increase the decryption buffer length to (orig_len+500)*3.
This is a hack, but at least it handles most cases. TLS compression should
really be disabled for EAP use of TLS, but since this can show up with
common setups, it is better to handle this case.
It looks like this SSL_set_options() value was added in 0.9.9 and it does
not exist in stable releases of OpenSSL. Fix build by using #ifdef on this
variable before use.
The middle byte of the secret (key for PRF) is shared with key halfs in
case the key length is odd. This does not happen in any of the current
tls_prf() uses, but it's better to fix this function to avoid future issues
should someone end up defining a use that uses an odd length for the key.
Process SoH Request in SoH EAP Extension method and reply with SoH TLV. The
contents of SSoH is not yet complete (i.e., some of the required attributes
are still missing). Use of SoH is disabled by default; it can be enabled
with tnc=soh in phase1 parameter for PEAP.
crypto_binding=# in phase1 network parameter can now be used to change the
PEAPv0 cryptobinding behavior (0 = do not use, 1 = optional (default),
2 = required).
Allow the user to set the IP address of the eapol_test client. This if
very useful when you have a machine with many interfaces and want to use a
particular one for testing RADIUS connectivity. For instance when I run the
national eduroam proxy I can only connect to other server from a particular
address, an our machine happens to have several IPs. So if I want to run
connectivity tests, I must make sure that my test uses a particular
interface. The -A option allows one to set this).
(jm: cleaned up to use radius configuration structure instead of global
variable for the address and added IPv6 support)
Implements the Chargable-User-Identity (CUI), as defined in RFC 4372.
Option "-i" causes the eapol_test to send a NUL CUI - which is a request to
send a CUI back. Capital "-I" allows to specify the value of the CUI.
This has been defined for cases where the client wants to reauthenticate.
If TNC is enabled, PEAPv0 server is now sending out SoH request to initiate
IF-TNCCS-SOH (Microsoft NAP / Statement of Health) handshake. The results
are currently only shown in debug log and they do not affect authentication
or authorization result.
The previous version was deriving unnecessarily large amount of output data
for the implicit challenge. With the TLS PRF, this was not causing any
problems because the output length is not explicitly bound into the
derivation. Anyway, it is better to use the correct output length should
the PRF be ever changed to a one that uses the output length to change the
beginning of the output data.
It looks like Microsoft implementation does not match with their
specification as far as PRF+ label usage is concerned.. IPMK|CMK is derived
without null termination on the label, but the label for CSK derivation
must be null terminated.
This allows cryptobinding to be used with PEAPv0 in a way that
interoperates with Windows XP SP3 (RC2) and as such, this functionality is
now enabled as an optional addition to PEAPv0.
Microsoft uses reverse order for MS-MPPE keys in EAP-PEAP when compared to
EAP-FAST derivation of ISK. Swap the keys here to get the correct ISK for
EAP-PEAPv0 cryptobinding. This resolves the cryptobinding interop issue
with WinXP SP3 RC2. However, it looks like MSK derivation does not
interoperate when using cryptobinding, so this code remains disabled for
the time being.
This implementation is complete for PEAPv0 (Microsoft extension), but the
use of cryptobinding is disabled in this version, i.e., this does not
change protocol behavior at all.
Interop tests between hostapd and wpa_supplicant work fine, but there are
some problems in getting hostapd to interoperate with Windows XP SP3 RC2
(peer replies with Result Failure to the attempted cryptobinding). The
implementation will remain disabled until this issue has been resolved.
EAP-PEAP was the only method that used the external eap_tlv.c peer
implementation. This worked fine just for the simple protected result
notification, but extending the TLV support for cryptobinding etc. is not
trivial with such separation. With the TLV processing integrated into
eap_peap.c, all the needed information is now available for using
additional TLVs.
EAP-PEAP was the only method that used the external eap_tlv.c server
implementation. This worked fine just for the simple protected result
notification, but extending the TLV support for cryptobinding etc. is not
trivial with such separation. With the TLV processing integrated into
eap_peap.c, all the needed information is now available for using
additional TLVs.
This adds support for PS3 wireless to wpa_supplicant.
Although PS3 wireless driver is designed to conform the WEXT standard
as much as possible, unfortunately the wext driver wrapper of
wpa_supplicant can not support PS3 wireless fully because:
- PS3 wireless driver uses private WEXT ioctls for accepting PSK of
WPA-Personal from the userland.
WEXT does not specify the way to do it.
- The association and 4-way handshake are done by PS3 virtual
wireless device. The guest OSes can not interfere it.
- No EAPOL frames are allowed to go outside of the
hypervisor/firmware nor come from. They are eaten by the firmware.
Thus I needed to make a new driver wrapper for PS3 wireless.
This patch can be applied against the latest 0.6.x tree.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
The old version was using struct wpa_sm::bssid which is not necessarily
updated to point to the correct target address when doing over-the-air FT
since the address is used before the association has actually been
completed.
Transition. This fixes a potential issue where an incorrectly behaving AP
could send a group key update using the old (now invalid after reassociate)
PTK. This could also happen if there is a race condition between reporting
received EAPOL frames and association events.
Need to process EAP AVP after the non-EAP Phase 2 method. In addition,
EAP-TTLS/MSCHAPv2 needs special code for handling the starting of TNC after
extra roundtrip of MSCHAPv2 success message.
Tunneled EAP sequence is now used to perform both the authentication (e.g.,
using EAP-GTC) and TNC validation (EAP-TNC) inside the EAP-FAST tunnel if
TNC has been enabled.
This adds EAP-TNC method and TNCS (IF-IMV and IF-TNCCS) functionality.
There is no integration with EAP-TTLS and EAP-FAST at this point, so this
version is not yet suitable for real use (i.e., EAP-TNC can only be tested
outside a tunnel which is not an allowed configuration for deployment).
However, the basic TNCS functionality is more or less complete and this
version seems to interoperate with wpa_supplicant.
Number of TLVs were processed in groups and these cases were now separated
into more flexible processing of one TLV at the time. wpabuf_concat()
function was added to make it easier to concatenate TLVs. EAP Sequences are
now supported in both server and peer code, but the server side is not
enabled by default.
This allows Phase 2 Identity Request to be skipped if the identity is
already known from PAC-Opaque received in TLS handshake in order to save
one roundtrip from normal authentication.
This allows associations to be denied if the STA tries to use too large
listen interval. The default value is 65535 which matches with the field
size limits.
These are expected in most cases and there is no need to confuse users
with the messages in stderr (perror was used here). These are now only
shown in debug output and EOPNOTSUPP errors are silently ignored.
