Add support for configuring parameters for the MU EDCA Parameter Set
element per IEEE P802.11ax/D3.0.
Signed-off-by: Siva Mullati <siva.mullati@intel.com>
When an interface is re-enabled after it was disabled during CAC, it
won't ever get active since hostapd is waiting for a CAC_FINISHED while
kernel side is waiting for a CMD_RADAR_DETECT to start a CAC.
This commit checks for a pending CAC when an interface is enabled and if
so restarts its DFS processing.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
While the AP is configured to enable both FT-PSK and WPA-PSK, an HP
printer request both AKMs (copied from AP?) in Association Request
frame, but don't add MDIE and don't use FT. This results in the
connection failing.
Next in logs we see:
RSN: Trying to use FT, but MDIE not included
IE - hexdump(len=26): 30 18 01 00 00 0f ac 04 01 00 00 0f ac 04
02 00 00 0f ac 02 00 0f ac 04 00 00
This is seen with some HP and Epson printers. Work around this by
stripping FT AKM(s) when MDE is not present and there is still a non-FT
AKM available.
Signed-off-by: Janusz Dziedzic <janusz@plumewifi.com>
While selecting a new channel as a reaction to radar event we need to
take into account supported bandwidth for each channel provided via
nl80211. Without this modification hostapd might select an unsupported
channel that would fail during AP startup.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
While doing automatic channel selection we need to take into account
supported bandwidth for each channel provided via nl80211. Without this
modification hostapd might select an unsupported channel which would
fail during AP startup.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
This adds checks to common code to verify supported bandwidth options
for each channel using nl80211-provided info. No support of additional
modes is added, just additional checks. Such checks are needed because
driver/hardware can declare more strict limitations than declared in the
IEEE 802.11 standard. Without this patch hostapd might select
unsupported channel and that will fail because Linux kernel does check
channel bandwidth limitations.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Add support for 160 MHz BW channels to automatic channel selection
algorithm. Only 36 and 100 channels are supported as 160 MHz channels.
Signed-off-by: Dmitry Lebed <lebed.dmitry@gmail.com>
FT-over-the-DS has a special case where the STA entry (and as such, the
TK) has not yet been configured to the driver depending on which driver
interface is used. For that case, allow add-STA operation to be used
(instead of set-STA). This is needed to allow mac80211-based drivers to
accept the STA parameter configuration. Since this is after a new
FT-over-DS exchange, a new TK has been derived after the last STA entry
was added to the driver, so key reinstallation is not a concern for this
case.
Fixes: 0e3bd7ac68 ("hostapd: Avoid key reinstallation in FT handshake")
Signed-off-by: Jouni Malinen <j@w1.fi>
The documentation in the hostapd.conf file says that the dynamic_vlan
variable is used to control whether VLAN assignments are accepted from a
RADIUS server. The implication seems to be that a static VLAN assignment
will come from the accept_mac_file if dynamic_vlan is set to 0, and a
dynamic assignment will come from the RADIUS server if dynamic_vlan is
set to 1. Instead, I'm seeing that the static settings from the
accept_mac_file are ignored if dynamic_vlan is set to 0, but used if
dynamic_vlan is set to 1. If dynamic_vlan is set to 1 and the RADIUS
server does not provide a VLAN, then the accept_mac_file assignment is
overridden and the STA is assigned to the default non-VLANed interface.
If my understanding of the expected behavior is correct, then I believe
the problem is in ap_sta_set_vlan(). That routine checks the
dynamic_vlan setting, but has no way of determining whether the incoming
vlan_desc is static (i.e., from accept_mac_file) or dynamic (i.e., from
a RADIUS server).
I've attached a patch that gets hostapd working as I believe it's meant
to, and updates the documentation to make the implicit behavior
explicit.
The functional changes are:
- hostapd_allowed_address() will always extract the vlan_id from the
accept_macs file. It will not update the vlan_id from the RADIUS cache
if dynamic_vlan is DISABLED.
- hostapd_acl_recv_radius() will not update the cached vlan_id if
dynamic_vlan is DISABLED.
- ieee802_1x_receive_auth() will not update the vlan_id if dynamic_vlan
is DISABLED.
More cosmetic:
Most of the delta is just moving code out of ieee802_1x_receive_auth()
into a new ieee802_1x_update_vlan() routine. While I initially did this
because the new DISABLED check introduced excessive indentation, it has
the added advantage of eliminating the vlan_description allocation and
os_memset() call for all DYNAMIC_VLAN_DISABLED configs.
I've done a couple rounds of review offline with Michael Braun (who has
done much of the work in this part of the code) and incorporated his
feedback.
If dynamic_vlan=0 (disabled), vlan assignments will be managed using the
local accept_mac_file ACL file, even if a RADIUS server is being used
for user authentication. This allows us to manage users and devices
independently.
Signed-off-by: Nils Nieuwejaar <nils.nieuwejaar@gmail.com>
After performing a successful channel switch, the AP should update its
own neighbor report element, so do this from src/ap/drv_callbacks.c
after a successful switch.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Move functions corresponding to neighbor report elements to
src/ap/neighbor_db.[c,h] in preparation to using them after channel
switch from src/ap/drv_callbacks.c.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Legacy ioctl() through SIOCDEVPRIVATE are deprecated. Follow the
approach taken by bridge-utils and make use of new bridge ioctl's
whenever possible.
For example, using legacy ioctl() breaks dynamic VLAN mode on 32-bit
Linux systems running 64-bit kernels.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
If the internal EAP server is used instead of an external RADIUS server,
sm->identity does not get set. Use the identity from the internal EAP
server in such case to get the dot1xAuthSessionUserName value in STA MIB
information.
Signed-off-by: Jouni Malinen <j@w1.fi>
Try to make RSSI-based rejection of associating stations a bit less
likely to trigger false rejections by considering RSSI from the last
received Authentication frame. Association is rejected only if both the
Authentication and (Re)Association Request frames are below the RSSI
threshold.
Signed-off-by: Jouni Malinen <j@w1.fi>
An AP might reject a STA association request due to low RSSI. In such
case, the AP informs the STA the desired RSSI improvement and a retry
timeout. The STA might retry to associate even if the RSSI hasn't
improved if the retry timeout expired.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Add the ability to ignore time-based CRL errors from OpenSSL by
specifying a new configuration parameter, check_crl_strict=0.
This causes the following:
- This setting does nothing when CRL checking is not enabled.
- When CRL is enabled, "strict mode" will cause CRL time errors to not
be ignored and will continue behaving as it currently does.
- When CRL is enabled, disabling strict mode will cause CRL time
errors to be ignored and will allow connections.
By default, check_crl_strict is set to 1, or strict mode, to keep
current functionality.
Signed-off-by: Sam Voss <sam.voss@rockwellcollins.com>
This makes it possible to use ECDSA certificates with EAP-TLS/TTLS/etc.
It should be noted that when using Suite B, different mechanism is used
to specify the allowed ECDH curves and this new parameter must not be
used in such cases.
Signed-off-by: Hristo Venev <hristo@venev.name>
handle_dhcp() was first trying to learn the IP address of an associated
STA before doing broadcast-to-unicast conversion. This could result in
not converting some DHCPACK messages since the address learning part
aborts processing by returning from the function in various cases.
Reorder these operations to allow broadcast-to-unicast conversion to
happen even if an associated STA entry is not updated based on a
DHCPACK.
Signed-off-by: Jouni Malinen <j@w1.fi>
These do not really get truncated in practice, but it looks like some
newer compilers warn about the prints, so silence those by checking the
result and do something a bit more useful if the output would actually
get truncated.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to integrate dynamic VLANs in custom network
configurations. The bridge name is added after the interface name in the
vlan_file line, also separated by whitespace.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable FTM responder and configure LCI and civic if ftm_responder
configuration option is set. Since ftm_responder configuration existed
before and was used to set extended capability bits, don't fail AP setup
flow if ftm_responder is set, but the driver doesn't advertise FTM
responder support.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The purpose of Multi-AP specification is to enable inter-operability
across Wi-Fi access points (APs) from different vendors.
This patch introduces one new configuration parameter 'multi_ap' to
enable Multi-AP functionality and to configure the BSS as a backhaul
and/or fronthaul BSS.
Advertise vendor specific Multi-AP capabilities in (Re)Association
Response frame, if Multi-AP functionality is enabled through the
configuration parameter.
A backhaul AP must support receiving both 3addr and 4addr frames from a
backhaul STA, so create a VLAN for it just like is done for WDS, i.e.,
by calling hostapd_set_wds_sta(). Since Multi-AP requires WPA2 (never
WEP), we can safely call hostapd_set_wds_encryption() as well and we can
reuse the entire WDS condition.
To parse the Multi-AP Extension subelement, we use get_ie(): even though
that function is meant for parsing IEs, it works for subelements.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Include and verify the OCI element in WNM-Sleep Exit Request and
Response frames. In case verification fails, the frame is silently
ignored.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
After the network changed to a new channel, perform an SA Query with the
AP after a random delay if OCV was negotiated for the association. This
is used to confirm that we are still operating on the real operating
channel of the network. This commit is adding only the station side
functionality for this, i.e., the AP behavior is not changed to
disconnect stations with OCV that do not go through SA Query.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Include an OCI element in SA Query Request and Response frames if OCV
has been negotiated.
On Linux, a kernel patch is needed to let clients correctly handle SA
Query Requests that contain an OCI element. Without this patch, the
kernel will reply to the SA Query Request itself, without verifying the
included OCI. Additionally, the SA Query Response sent by the kernel
will not include an OCI element. The correct operation of the AP does
not require a kernel patch.
Without the corresponding kernel patch, SA Query Requests sent by the
client are still valid, meaning they do include an OCI element.
Note that an AP does not require any kernel patches. In other words, SA
Query frames sent and received by the AP are properly handled, even
without a kernel patch.
As a result, the kernel patch is only required to make the client properly
process and respond to a SA Query Request from the AP. Without this
patch, the client will send a SA Query Response without an OCI element,
causing the AP to silently ignore the response and eventually disconnect
the client from the network if OCV has been negotiated to be used.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Include and verify the the OCI element in (Re)Association Request and
Response frames of the FT handshake. In case verification fails, the
handshake message is silently ignored.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Verify the received OCI element in the 4-way and group key handshakes.
If verification fails, the handshake message is silently dropped.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Use the information elements that were present in the (Re)Association
Request frame to derive the maximum bandwidth the AP will use to
transmit frames to a specific STA. By using this approach, we don't need
to query the kernel for this information, and avoid having to add a
driver API for that.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
If Operating Channel Verification is negotiated, include the OCI KDE
element in EAPOL-Key msg 2/4 and 3/4 of the 4-way handshake and both
messages of the group key handshake.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Set the OCV bit in RSN capabilities (RSNE) based on AP mode
configuration. Do the same for OSEN since it follows the RSNE field
definitions.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
APs and mesh peers use the VHT Operation element to advertise certain
channel properties (e.g., the bandwidth of the channel). Save this
information element so we can later access this information.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This adds the necessary functions and callbacks to make the channel_info
driver API available to the authenticator state machine that implements
the 4-way and group key handshake. This is needed for OCV.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This adds driver API functions to get the current operating channel
parameters. This encompasses the center frequency, channel bandwidth,
frequency segment 1 index (for 80+80 channels), and so on.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This adds support for hostapd-as-RADIUS-authentication-server to request
subscription remediation for SIM-based credentials. The new hostapd.conf
parameter hs20_sim_provisioning_url is used to set the URL prefix for
the remediation server for SIM provisioning. The random
hotspot2dot0-mobile-identifier-hash value will be added to the end of
this URL prefix and the same value is stored in a new SQLite database
table sim_provisioning for the subscription server implementation to
use.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new hostapd configuration parameter hs20_release can be used to
configure the AP to advertise a specific Hotspot 2.0 release number
instead of the latest supported release. This is mainly for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is better not to process a new (most likely repeated) FILS HLP
request if a station retransmits (Re)Association Request frame before
the previous HLP response has either been received or timed out. The
previous implementation ended up doing this and also ended up
rescheduling the fils_hlp_timeout timer in a manner that prevented the
initial timeout from being reached if the STA continued retransmitting
the frame. This could result in failed association due to a timeout on
the station side.
Make this more robust by processing (and relaying to the server) the HLP
request once and then ignoring any new HLP request while the response
for the relayed request is still pending. The new (Re)Association
Request frames are otherwise processed, but they do not result in actual
state change on the AP side before the HLP process from the first
pending request is completed.
This fixes hwsim test case fils_sk_hlp_oom failures with unmodified
mac80211 implementation (i.e., with a relatively short retransmission
timeout for (Re)Association Request frame).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If association failed for any non-OWE specific reason, the previous
implementation tried to add the OWE related IEs into the (Re)Association
Response frame. This is not needed and could actually result in
dereferencing a NULL pointer. Fix this by adding those OWE related IEs
only for successful association and only if the RSN state machine has
been initialized.
Signed-off-by: Jouni Malinen <j@w1.fi>
Both handle_action() and hostapd_action_rx() are used for processing
received Action frames depending on what type of driver architecture is
used (MLME in hostapd vs. driver) and which build options were used to
build hostapd. These functions had a bit different sequence for checking
the frame and printing debug prints. Make those more consistent by
checking that the frame includes the category-specific action field and
some payload. Add a debug print for both functions to make it easier to
see which path various Action frames use.
Signed-off-by: Jouni Malinen <j@w1.fi>
Avoid smatch warning on this even thought the only caller of the
function uses a non-NULL pointer in all cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Instead of going through the configuration exchange, reject invalid
legacy configurator parameters explicitly. Previously, configuring
legacy (psk/sae) parameters without psk/pass resulted in a config object
that used a zero length passphrase. With this change, that config object
is not sent and instead, either the initialization attempts is rejected
or the incoming initialization attempt is ignored.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new conf variable was used only within the CONFIG_TESTING_OPTIONS
block and as such, added a warning about unused variable into
non-testing builds. Fix that by using that variable outside the
conditional block as well.
Fixes: a22e235fd0 ("OWE: Add testing RSNE for OWE assoc response with driver SME/MLME")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
BSS additional/removal cases were not considered at all in the previous
implementation of hostapd configuration file reloading on SIGHUP. Such
changes resulted in num_bss values getting out of sync in runtime data
and configuration data and likely dereferencing of freed memory (e.g.,
when removing a BSS).
Fix this by forcing a full disable/enable sequence for the interface if
any BSS entry is added/removed or if an interface name changes between
the old and the new configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not try to determine the length of the T&C Server URL before checking
that the URL is available. This got broken in a change to move the
handling to the AS. hostapd could potentially have hit a NULL pointer
dereference if the authentication server sent an unconsistent set of T&C
information.
Fixes: d4e39c51f8 ("HS 2.0: Move Terms and Conditions Server URL generation from AP to AS")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Earlier, the OCE flags were checked during hostapd initialization. This
doesn't address few cases like for example when the interface is added
from control interface. Move the OCE flag checks to the functions that
are forming the MBO/OCE IEs to cover all the different paths for
enabling a BSS. Also use macros as appropriate for readability.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support for negotiating WNM Collocated Interference Reporting. This
allows hostapd to request associated STAs to report their collocated
interference information and wpa_supplicant to process such request and
reporting. The actual values (Collocated Interference Report Elements)
are out of scope of hostapd and wpa_supplicant, i.e., external
components are expected to generated and process these.
For hostapd/AP, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration. STAs are requested to perform
reporting with "COLOC_INTF_REQ <addr> <Automatic Report Enabled> <Report
Timeout>" control interface command. The received reports are indicated
as control interface events "COLOC-INTF-REPORT <addr> <dialog token>
<hexdump of report elements>".
For wpa_supplicant/STA, this mechanism is enabled by setting
coloc_intf_reporting=1 in configuration and setting Collocated
Interference Report Elements as a hexdump with "SET coloc_intf_elems
<hexdump>" control interface command. The hexdump can contain one or
more Collocated Interference Report Elements (each including the
information element header). For additional testing purposes, received
requests are reported with "COLOC-INTF-REQ <dialog token> <automatic
report enabled> <report timeout>" control interface events and
unsolicited reports can be sent with "COLOC_INTF_REPORT <hexdump>".
This commit adds support for reporting changes in the collocated
interference (Automatic Report Enabled == 1 and partial 3), but not for
periodic reports (2 and other part of 3).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
In case the protocol used for the BSS is WPA, the WPA vendor IE should
be placed after all the non vendor IEs. Fix this for Beacon and Probe
Response frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Previously, when an AP interface was disabled through a control
interface DISABLE command during a channel switch window, the interface
could not be reenabled due to beacon setup failure (which validates if
CSA is in progress).
Fix this by clearing channel switch parameters while disabling the
hostapd interface.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
When moving a 5 GHz VHT AP to 2.4 GHz band with VHT disabled through the
hostapd control interface DISABLE/reconfig/ENABLE commands, enabling of
the AP on 2.4 GHz failed due to the previously configured VHT capability
being compared with hardware VHT capability on 2.4 GHz band:
hw vht capab: 0x0, conf vht capab: 0x33800132
Configured VHT capability [VHT_CAP_MAX_MPDU_LENGTH_MASK] exceeds max value supported by the driver (2 > 0)
ap: interface state DISABLED->DISABLED
Since VHT (ieee80211ac) config is already disabled for the 2.4 GHz band,
add fix this by validating vht_capab only when VHT is enabled.
Fixes: c781eb8428 ("hostapd: Verify VHT capabilities are supported by driver")
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Previous implementation ended up triggering PMF check for previous
association and SA Query procedure incorrectly in cases where there is a
STA entry in hostapd, but that STA is not in associated state. This
resulted in undesired temporary rejection of the association with status
code 30.
This ended up breaking OWE group negotiation when PMF is in use since
the check for the OWE group would have happened only after this earlier
PMF check and rejection (i.e., the station got status code 30 instead of
the expected 77).
For example, when the AP is configured with OWE group 21 and a station
tries groups 19, 20, and 21 (in this sequence), the first two
Association Request frames should be rejected with status code 77.
However, only the first one got that status code while the second one
got status code 30 due to that issue with PMF existing association
check.
Furthermore, hostapd was continuing with SA Query procedure with
unencrypted Action frames in this type of case even though there was no
existing association (and obviously, not an encryption key either).
Fix this by checking that the STA entry is in associated state before
initiating SA Query procedure based on the PMF rules.
Signed-off-by: Ashok Kumar <aponnaia@codeaurora.org>
Without this patch sae_require_mfp is always activate, when ieee80211w
is set to optional all stations negotiating SAEs are being rejected when
they do not support PMF. With this patch hostapd only rejects these
stations in case sae_require_mfp is set to some value and not null.
Fixes ba3d435fe4 ("SAE: Add option to require MFP for SAE associations")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This message was printed and MSG_INFO level which would be more
reasonable for error cases where hostapd has accepted authentication.
However, this is not really an error case for the cases where
authentication was rejected (e.g., due to MAC ACL). Drop this to use
MSG_DEBUG level.
Signed-off-by: Jouni Malinen <j@w1.fi>
When Probe Request frame handling was extended to use MAC ACL through
ieee802_11_allowed_address(), the MSG_INFO level log print ("Station
<addr> not allowed to authenticate") from that function ended up getting
printed even for Probe Request frames. That was not by design and it can
result in excessive logging and MSG_INFO level if MAC ACL is used.
Fix this by printing this log entry only for authentication and
association frames. In addition, drop the priority of that log entry to
MSG_DEBUG since this is not really an unexpected behavior in most MAC
ACL use cases.
Fixes: 92eb00aec2 ("Extend ACL check for Probe Request frames")
Signed-off-by: Jouni Malinen <j@w1.fi>
Extend hostapd to allow the new OSU Provider NAI List ANQP-element to be
advertised in addition to the previously used OSU Providers list
ANQP-element. The new osu_nai2 configurator parameter option is used to
specify the OSU_NAI value for the shared BSS (Single SSID) case while
osu_nai remains to be used for the separate OSU BSS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If you modify the WLAN-STA-AUTHORIZED bit in sta->flags, you have to
call the ap_sta_set_authorized() function to make sure the corresponding
event is sent over the control interface. Otherwise we leak entries in
the event history.
Signed-off-by: Andreas Tobler <andreas.tobler@cloudguard.ch>
When CONFIG_OWE is enabled but none of 11R/11W/FILS are enabled hostapd
(and wpa_supplicant with AP mode support) build failed. Fix this by
adding OWE to the list of conditions for including the local variables.
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
This enhances DPP_AUTH_INIT, DPP_CONFIGURATOR_SIGN, and SET
dpp_configurator_params to allow optional setting of the DPP groupId
string for a Connector. If the value is not set, the previously wildcard
value ("*") is used by default.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows WEP mode AP to be re-enabled automatically after external
ifconfig down + up on netdev used by hostapd.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make it clear that the consideration should be only for the IBSS case
and in infrastructure BSS case, PMKID KDE should not be added due to
risks involved with exposing this to stations that do not know the
passphrase.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it more convenient to generate the URL in a way that
interoperates between different vendors. The AP is simply copying the
already constructed URL as-is from Access-Accept to WNM-Notification.
This means that the HO AAA can generate the URL in a manner that works
for the associated T&C Server without having to coordinate with each AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
In the infrastructure BSS case, the AP needs to clear pending SAE state
if a new Commit message is received when already in Committed state.
This allows the non-AP STA to negotiate a new group if it ends up trying
to go through SAE authentication again before the AP side has removed
the previous STA entry.
This fixes an issue where a kernel update changed something in SAE
timing or authentication sequence and started failing the
sae_bignum_failure hwsim test case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When removing an interface, hostapd_bss_deinit() frees all associated
STAs. If any of the stations is 40MHz intolerant, the cleanup invokes
ht40_intolerant_remove(), that in turn registers a 20->40MHz transition
timer for the last station (ap_ht2040_timeout() function). That timer is
never canceled; once it executes, the interface is gone, most likely
resulting in a segfault when referencing it.
While hostapd_interface_deinit() cancels the transition timer, it does
so before cleaning up STAs. Move the cancellation after STA cleanup to
cancel any timer that was registered during that operation.
Signed-off-by: Martin Willi <martin@strongswan.org>
The AKM 00-0F-AC:13 is supposed to use cryptographic algorithms
consistently, but the current IEEE 802.11 standard is not doing so for
the key names: PMKID (uses SHA-1), PMKR0Name/PMKR1Name (uses SHA-256).
The PMKID case was already implemented with SHA-384 and this commit
replaces use of SHA-256 with SHA-384 for PMKR0Name/PMKR1Name derivation
to be consistent in SHA-384. While this is not compliant with the
current IEEE 802.11 standard, this is clearly needed to meet CNSA Suite
requirements. Matching change is being proposed in REVmd to get the IEEE
802.11 standard to meet the use case requirements.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
A new SAE Commit message should not be allowed to drop an existing STA
entry since the sender of that Commit message cannot be authenticated
before receiving the Confirm message. This is important in particular
when PMF is used since this would provide a potential new path for
forcing a connection to be dropped.
Fix this by allowing a new SAE Authentication instance to be started
when the old instance is in Accepted state and the new Commit message
does not use the same peer-scalar value (checked in
sae_parse_commit_scalar()). When PMF is used, the AP will use SA Query
procedure when receiving the (Re)Association Request frame. In theory,
that step could be skipped in case of SAE Authentication since the
non-AP STA is demonstrating knowledge of the password. Anyway, there is
no allowance for that exception in the IEEE 802.11 standard, so at least
for now, leave this using SA Query procedure just like any other PMF
case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd was hardcoded to use 128-bit IGTK in FT protocol (IGTK
subelement in FTE). Extend that to allow 256-bit IGTK (i.e.,
BIP-CMAC-256 and BIP-GMAC-256) to be used as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of sending out a partially completed frame, abort the
association process if something unexpected happens and remove the STA
entry.
Signed-off-by: Jouni Malinen <j@w1.fi>
When support for KCK2 and KEK2 was added, both keys were derived for
FT-FILS cases, but only KCK2 was actually used. Add similar changes to
use KEK2 to protect GTK/IGTK in FTE with using FT-FILS AKMs.
This fixes AES key wrapping to use the correct key. The change is not
backwards compatible.
Fixes: 2f37387812 ("FILS: Add more complete support for FT-FILS use cases")
Signed-off-by: Jouni Malinen <j@w1.fi>
When building an RRB message, a failure in wpa_ft_rrb_lin() calls could
have resulted in trying to free an uninitialized pointer. Fix this by
initializing *packet to NULL before going through the initial steps.
Signed-off-by: Jouni Malinen <j@w1.fi>
SHA384-based FT AKM uses longer keys, so the RRB receive processing for
push and pull response messages needs to be able to accept variable
length PMK-R1.
Signed-off-by: Jouni Malinen <j@w1.fi>
The MIC field is now a variable length field, so make FTE generation in
hostapd aware of the two different field lengths.
Signed-off-by: Jouni Malinen <j@w1.fi>
This defines key lengths for SHA384-based FT AKM and handles writing and
parsing for RSNE AKMs with the new value.
Signed-off-by: Jouni Malinen <j@w1.fi>
If time_advertisement=2 is included in hostapd configuration, but
time_zone is unset, the previous implementation tried to write the Time
Zone element into management frames. This resulted in segmentation fault
when trying to dereference a NULL pointer. Fix that by skipping addition
of this element when time_zone parameter is not set.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
This allows a single BSS/SSID to be used for both data connection and
OSU. Instead of hostapd configuration osen=1, wpa_key_mgmt=OSEN (or more
likely, wpa_key_mgmt=WPA-EAP OSEN) is used to enable this new option.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These changes add support for salted password databases to EAP-pwd per
RFC 8146. This commits introduces the framework for enabling this and
the salting mechanisms based on SHA-1, SHA256, and SHA512 hash
algorithms.
Signed-off-by: Dan Harkins <dharkins@lounge.org>
This extends the SAE implementation in both infrastructure and mesh BSS
cases to allow an optional Password Identifier to be used. This uses the
mechanism added in P802.11REVmd/D1.0. The Password Identifier is
configured in a wpa_supplicant network profile as a new string parameter
sae_password_id. In hostapd configuration, the existing sae_password
parameter has been extended to allow the password identifier (and also a
peer MAC address) to be set. In addition, multiple sae_password entries
can now be provided to hostapd to allow multiple per-peer and
per-identifier passwords to be set.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, hostapd CHAN_SWITCH command did not effect VHT configuration
for the following:
When VHT is currently disabled (ieee80211ac=0),
1. hostapd_cli -p /var/run/hostapd chan_switch 10 5180 \
sec_channel_offset=1 center_freq1=5190 bandwidth=40 ht
====> Comes up in HT40
2. hostapd_cli -p /var/run/hostapd chan_switch 10 5765 \
sec_channel_offset=-1 center_freq1=5775 bandwidth=40 vht
====> Comes up in HT40
3. hostapd_cli -p /var/run/hostapd chan_switch 10 5200 center_freq1=5200 \
bandwidth=20 vht
====> Comes up in HT20
When VHT is currently enabled (ieee80211ac=1),
1. hostapd_cli -p /var/run/hostapd chan_switch 10 5180 \
sec_channel_offset=1 center_freq1=5190 bandwidth=40 ht
====> Comes up in VHT40
2. hostapd_cli -p /var/run/hostapd chan_switch 10 5200 center_freq1=5200 \
bandwidth=20 ht
====> Comes up in VHT20
This is since VHT config from chan_switch is processed only for
bandwidths 80 and above (80P80, 160) and for VHT20, VHT40 cases, only
NLA chan type and chan width are updated.
There is no NL attribute for determining if it is HT or VHT for
bandwidths 20 & 40 and currently they are updated as HT20, HT40 (+ or -
depending on offset). Same is notified back via
NL80211_CMD_CH_SWITCH_NOTIFY.
Instead of adding new NL attribute for tracking HT/VHT enabled config,
we are adding new hostapd VHT config parameter to save the chan_switch
config and use only for chan_switch case of VHT20 and VHT40.
Tested with all combinations of chan_switch (noHT->20->40->80->) HT/VHT
and confirmed to be working.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
When the channel time is zero the interference factor calculation falls
under divide by zero operation which results in invalid (NaN =
not-a-number) interference factor value. This leads to wrong ideal
channel selection in ACS during the scenario described below.
Scenario:
In VHT80 mode, the channel 36 (first channel) gets the channel time as
zero which causes the interfactor factor to be an invalid number (NaN).
Any operations (like addition, mulitplication, divide, etc.) with NaN
value results in a NaN value, so that average factor for the primary
channel 36 got the invalid value (NaN). Since channel 36 is the first
channel, ideal factor is assigned as NaN in the first iteration. The
following iteration condition check (factor < ideal_factor) with a NaN
value fail for all other primary channels. This results in channel 36
being chosen as the ideal channel in ACS which holds a NaN value.
Logs:
ACS: Survey analysis for channel 36 (5180 MHz)
ACS: 1: min_nf=-103 interference_factor=nan nf=0 time=0 busy=0 rx=0
ACS: 2: min_nf=-103 interference_factor=0.615385 nf=-102 time=13 busy=8 rx=0
ACS: 3: min_nf=-103 interference_factor=2.45455 nf=0 time=22 busy=16 rx=0
ACS: 4: min_nf=-103 interference_factor=0.785714 nf=-103 time=42 busy=33 rx=0
ACS: 5: min_nf=-103 interference_factor=nan nf=0 time=0 busy=0 rx=0
ACS: * interference factor average: nan
...
ACS: * channel 36: total interference = nan
..
ACS: * channel 149: total interference = 5.93174e-21
..
ACS: Ideal channel is 36 (5180 MHz) with total interference factor of nan
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
The current EAP peer implementation is not yet ready for the TLS v1.3
changes with EAP-TTLS, EAP-PEAP, and EAP-FAST, so disable TLS v1.3 for
this EAP method for now.
While the current EAP-TLS implementation is more or less complete for
TLS v1.3, there has been no interoperability testing with other
implementations, so disable for by default for now until there has been
chance to confirm that no significant interoperability issues show up
with TLS version update. tls_flags=[ENABLE-TLSv1.3] configuration
parameter can be used to enable TLS v1.3 (assuming the TLS library
supports it; e.g., when using OpenSSL 1.1.1).
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow hostapd RADIUS authentication server with SQLite EAP user DB to be
used for testing Terms and Conditions functionality. This could be used
for the HO AAA part of functionality (merging HO AAA and SP AAA into a
single component to avoid separate RADIUS proxy in testing setup).
A T&C server with HTTPS processing is needed to allow this to be used
for full over-the-air testing. This commit adds sufficient functionality
to allow hwsim test cases to cover the RADIUS server part.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend RADIUS DAS to support CoA-Request packets for the case where the
HS 2.0 Terms And Conditions filtering VSA is used to remove filtering.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Mark a channel as required DFS based on regulatory information received
from the driver/kernel rather than deciding based on hardcoded
boundaries on the frequency. Previously few channels were being marked
as requiring DFS even though they were non-DFS in a particular country.
If the driver does not provide channel list information, fall back to
the previously used frequency-based determination.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd Access-Accept processing to check if the RADIUS
server indicated that Terms and Conditions Acceptance is required. The
new hs20_t_c_server_url parameter is used to specify the server URL
template that the STA is requested to visit.
This commit does not enable any kind of filtering, i.e., only the part
of forwarding a request from Access-Accept to the STA using
WNM-Notification is covered.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd with two new configuration parameters
(hs20_t_c_filename and hs20_t_c_timestamp) that can be used to specify
that the Terms and Conditions attributes are to be added into all
Access-Request messages for Hotspot 2.0 STAs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows user to get event indication when a new interface is
added/removed for 4addr WDS STA and also WDS STA ifname is informed
through the STA command.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
When AP initialization is completed in a callback (e.g., OBSS scan),
wpa_supplicant_deinit_ap() is not called in case of failure. Fix this by
calling setup_complete_cb in case of failure, too, which in turn calls
wpa_supplicant_deinit_ap() if needed.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
This extends hostapd processing of (Re)Association Request frames to
store a local copy of the Consortium OI within the Roaming Consortium
Selection element, if present, and then add that in HS 2.0 Roaming
Consortium attribute into RADIUS Access-Request messages.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd Hotspot 2.0 implementation to allow operator icons
to be made available. The existing hs20_icon parameter is used to define
the icons and the new operator_icon parameter (zero or more entries) is
used to specify which of the available icons are operator icons. The
operator icons are advertised in the Operator Icon Metadata ANQP-element
while the icon data can be fetched using the same mechanism (icon
request/binary file) that was added for the OSU Providers icons.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If there is no explicit wmm_enabled parameter in the configuration
(i.e., conf->wmm_enabled == -1), the configuration reload path needs to
initialize conf->wmm_enabled based on iconf->ieee80211n in
hostapd_reload_bss() similarly to what is done in the initial startup
case in hostapd_setup_bss().
This fixes issues with RSN capabilities being set incorrectly when WMM
is supposed to get enabled and unexpectedly enabling WMM when it is not
supposed to be enabled (HT disabled). Either of these issues could show
up when asking hostapd to reload the configuration file (and when that
file does not set wmm_enabled explicitly).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This ensures a session timeout configured on R0KH either using
RADIUS-based ACL or 802.1X authentication is copied over to the new
R1KH.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This is needed to allow the remaining session time to be computed for FT
(when sending PMK-R1 to another AP).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Handle the special case of no PMK-R0 entry in the caller instead of
having to have wpa_ft_rrb_build_r0() aware of the possibility of pmk_r0
being NULL.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
ieee802_11_set_radius_info() might be called with a STA entry that has
already stored identity and/or radius_cui information, so make sure the
old values get freed before being replaced by the new ones.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This uses set_vlan()/get_vlan() callbacks to fetch and configure the
VLAN of STA. Transmission of VLAN information between APs uses new TLVs.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
IEEE Std 802.11-2016, 12.7.1.7.1 indicates that the lifetime of the
PMK-R0 (and PMK-R1) is bound to the lifetime of PSK or MSK from which
the key was derived. This is currently stored in r0_key_lifetime, but
cache entries are not actually removed.
This commit uses the r0_key_lifetime configuration parameter when
wpa_auth_derive_ptk_ft() is called. This may need to be extended to use
the MSK lifetime, if provided by an external authentication server, with
some future changes. For PSK, there is no such lifetime, but it also
matters less as FT-PSK can be achieved without inter-AP communication.
The expiration timeout is then passed from R0KH to R1KH. The R1KH verifies
that the given timeout for sanity, it may not exceed the locally configured
r1_max_key_lifetime.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
FILS calls wpa_ft_store_pmk_r0() from wpa_auth.c. This is moved into a
new function wpa_ft_store_pmk_fils() in preparation of additional
information being needed.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Add a new configuration option ft_r0_key_lifetime that deprecates
r0_key_lifetime. Though, the old configuration is still accepted for
backwards compatibility.
This simplifies testing. All other items are in seconds as well. In
addition, this makes dot11FTR0KeyLifetime comment match with what got
standardized in the end in IEEE Std 802.11r-2008.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
When locating the position of the IGTK PN in the key data, we also need
to skip the KDE header, in addition to the keyid field. This fixes
hostapd RESEND_M3 and RESEND_GROUP_M1 behavior when PMF is negotiated
for the association. Previously, the IGTK KDE ended up getting
practically hidden since zeroing of the PN ended up clearing the KDE OUI
and Type fields.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
The new venue_url parameter can now be used to set the Venue URL ANQP
information instead of having to construct the data and use
anqp_elem=277:<hexdump> to set the raw value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends the original IEEE Std 802.11ai-2016 functionality with the
changes added in REVmd to describe how additional keys are derived to
protect the FT protocol using keys derived through FILS authentication.
This allows key_mgmt=FT-FILS-SHA256 to be used with FT protocol since
the FTE MIC can now be calculated following the changes in REVmd. The
FT-FILS-SHA384 case is still unsupported (it needs support for variable
length MIC field in FTE).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Derive PMK-R1 locally if the derived PMKR1Name is not found from the
local cache, but the request is for a key that was originally generated
locally (R0KH-ID matches) and the PMKR0Name is found in the local cache.
This was apparently not hit in the previously used FT sequences, but
this is useful to have available if a PMK-R1 entry is dropped from the
local cache before PMK-R0.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the requested key is not available locally, there is no point in
trying to send a pull request back to self for the key.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, the association that used SAE authentication ended up
recalculating the PMKID for EAPOL-Key msg 1/4 using incorrect
PMK-to-PMKID derivation instead of using the previously derived PMKID
from SAE. The correct PMKID was used only when going through PMKSA
caching exchange with a previously derived PMKSA from SAE.
Fix this by storing the SAE PMKID into the state machine entry for the
initial SAE authentication case when there is no explicit PMKSA entry
attached to the station.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When processing 20/40 BSS Coexistence Management frames that do not
explicitly require 40 MHz to be disabled, check whether the reported
channels in 20/40 BSS Intolerant Channel Report element match the
current primary channel. If so, allow 40 MHz operation to continue. This
makes the during-operation updates for 20/40 Operation Permitted more
consistent with the scans during initial BSS startup.
The received 20/40 BSS Intolerant Channel Report channels are to be used
in the OT set in the during-operation determination and the P == OT_i
exception was ignored in the previous implementation which could result
in the AP first starting with 40 MHz and then dropping to 20 MHz on
first received 20/40 BSS Coexistence Management frame even though there
was no change in the neighboring BSSs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends 20/40 BSS Coexistence Management frame processing to
iterate over all the included 20/40 BSS Intolerant Channel Report
elements instead of using only the first one.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The 20 MHz BSS Width Request field is set to 1 only for intra-BSS
reports. As such, ignore the frame if such a claim is made by a
transmitter that is not currently associated with the AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it easier to understand what kind of information a STA is
reporting about 20/40 MHz coexistence requirements.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Ignore hostapd_event_sta_low_ack for a station which has agreed to
steering by checking the agreed_to_steer flag. This flag will be set
whenever a station accepts the BSS transition request from the AP.
Without this ignoring of the LOW_ACK event, the steering in-progress
might be affected due to disassociation. In this way AP will allow some
time (two seconds) for the station to move away and reset the flag after
the timeout.
Co-Developed-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Add an event callback for EVENT_STATION_OPMODE_CHANGED to allow
user/application to get the notification whenever there is a change in a
station's HT/VHT op mode.
The new events:
STA-OPMODE-MAX-BW-CHANGED <addr> <20(no-HT)|20|40|80|80+80|160>
STA-OPMODE-SMPS-MODE-CHANGED <addr> <automatic|off|dynamic|static>
STA-OPMODE-N_SS-CHANGED <addr> <N_SS>
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
This allows external application to get last ACK signal strength of the
last transmitted frame if the driver makes this information
(NL80211_STA_INFO_ACK_SIGNAL) available.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Check wpa_auth_write_assoc_resp_owe() return value to keep static
analyzers happier. The code path where this could happen is not really
reachable due to the separate hapd->conf->own_ie_override check and
wpa_auth_write_assoc_resp_owe() returning NULL only in an error case in
the override path. Furthermore, clean up the pointer return value to use
a proper pointer (NULL vs. 0).
Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
To retain configurator information across hostapd/wpa_supplicant
restart, private key need to be maintained to generate a valid pair of
authentication keys (connector, netaccess_key, csign) for new enrollees
in the network.
Add a DPP_CONFIGURATOR_GET_KEY control interface API through which the
private key of an existing configurator can be fetched.
Command format:
DPP_CONFIGURATOR_GET_KEY <configurator_id>
The output from this command can then be used with
"DPP_CONFIGURATOR_ADD key=<hexdump>" to create the same key again.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The SAE AKM 00-0F-AC:8 is supposed to use EAPOL-Key Key Descriptor
Version 0 (AKM-defined) with AES-128-CMAC and NIST AES Key Wrap.
However, the previous implementation ended up using Key Descriptor
Version 2 (HMAC-SHA-1-128 and NIST AES Key Wrap). Fix this by using the
appropriate Key Descriptor Version and integrity algorithm. Use helper
functions to keep the selection clearer and more consistent between
wpa_supplicant and hostapd uses.
Note: This change is not backwards compatible. Both the AP and station
side implementations will need to be updated at the same time to
maintain functionality.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends dpp_test functionality to allow DPP exchanges to be stopped
after authentication is completed on the Initiator, i.e., after sending
out the Authentication Confirm message. Previously, dpp_test=89 was used
only on the Responder side to stop after receiving the Authentication
Confirm message. The main use case for this extended functionality is to
be able to stop the protocol exchange on a device that acts as
authentication Initiator and Enrollee.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
enum wpa_alg was being compared with WPA_CIPHER_* values. That does not
work here and strict compilers will report this as an error. Fix the
comparision to use proper WPA_ALG_* values. This fixes testing
capability for resetting IPN for BIP.
Fixes: 16579769ff ("Add testing functionality for resetting PN/IPN for configured keys")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend ACL check to deny Probe Request frames for the client which does
not pass ACL check. Skip this check for the case where RADIUS ACL is
used to avoid excessive load on the RADIUS authentication server due to
Probe Request frames. This patch add wpa_msg event for auth and assoc
rejection due to acl reject.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
For FILS, __wpa_send_eapol() is called only with the kde != NULL, but a
static analyzer might not understand that. Add an explicit check kde !=
NULL similarly to the other cases going through the kde parameter to
silence such bogus warnings.
Signed-off-by: Jeffin Mammen <jmammen@codeaurora.org>
Commit e61fea6b46 ('SAE: Fix PMKSA caching
behavior in AP mode') modified the PSK fetching loop to not override PMK
in case of SAE with PMKSA caching. However, that commit missed the error
path cases where there is need to break from the loop with exact
negative of the check in the beginning of the loop. This could result in
hitting an infinite loop in hostapd if a station derived a different PMK
value from otherwise successfully completed SAE authentication or if a
STA used a different PMK with a PMKSA caching attempt after a previously
completed successful authentication.
Fix this by adding the matching break condition on SAE AKM within the
loops.
Fixes: e61fea6b46 ("SAE: Fix PMKSA caching behavior in AP mode")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check for the fi parameter to be non-NULL before trying to fetch the
ssi_signal information similarly to how the fi->freq was already
handled. While the meta information is supposed to be available, it
looks like there is at least one corner case where fi == NULL could be
used (Authentication frame reprocessing after RADIUS-based ACL).
Signed-off-by: Jouni Malinen <j@w1.fi>
Reject SAE association request when PMKID is included in the RSNE, but
the corresponding PMKSA is not available in the AP.
Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
This function is used to process a (Re)Association Request frame, so
rename it appropriately to mention assoc_req instead of auth_req.
Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
Verify that the STA has ECDH data available before trying to use this
data to add the OWE DH Params element.
Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
This was already the case with the hostapd-based SME/MLME
implementation, but the OWE DH Param element construction for the
driver-based SME/MLME needed a matching change to set the group
properly.
Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
For FT-PSK sm->xxkey was populated with only the first password on the
linked list (i.e., last matching password in the wpa_psk_file) in
INITPSK. This caused only that password to be recognized and accepted.
All other passwords were not verified properly and subsequently
prevented clients from connecting.
Hostapd would report:
Jan 30 12:55:44 hostapd: ap0: STA xx:xx:xx:xx:xx:xx WPA: sending 1/4 msg of 4-Way Handshake
Jan 30 12:55:44 hostapd: ap0: STA xx:xx:xx:xx:xx:xx WPA: received EAPOL-Key frame (2/4 Pairwise)
Jan 30 12:55:44 hostapd: ap0: STA xx:xx:xx:xx:xx:xx WPA: invalid MIC in msg 2/4 of 4-Way Handshake
Jan 30 12:55:45 hostapd: ap0: STA xx:xx:xx:xx:xx:xx WPA: EAPOL-Key timeout
Signed-off-by: Michal Kazior <michal@plumewifi.com>
Use the preprocessor conditional "ifdef" instead of "if" before
CONFIG_TESTING_OPTIONS to prevent an issue on build systems that treat
undefined preprocessor identifiers as an error.
Signed-off-by: David Messer <david.messer@garmin.com>
If a matching PMKSA cache entry is present for an OWE client, use it and
do not go through DH while processing Association Rquest frame.
Association Response frame will identify the PMKID in such a case and DH
parameters won't be present.
Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
Handle OWE unsupported finite cyclic group in (Re)Association Request
frame when not using the hostapd SME/MLME.
Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
Send Public Action frames with wildcard BSSID when destination was
broadcast address. This is required for DPP PKEX where the recipients
may drop the frames received with different BSSID than the wildcard
address or the current BSSID.
Signed-off-by: Ashok Ponnaiah <aponnaia@codeaurora.org>
FILS capability bit setting could have ended up setting boths biths 72
(correct) and 64 (incorrect; part of Max Number of MSDUs In A-MSDU). Fix
this by adding the missing break to the switch statement.
Fixed: f55acd909e ("FILS: Set FILS Capability bit in management frames from AP")
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes hostapd use the WLAN-Reason-Code value from Access-Reject
when disconnecting a station due to IEEE 802.1X authentication failure.
If the RADIUS server does not include this attribute, the default value
23 (IEEE 802.1X authentication failed) is used. That value was the
previously hardcoded reason code.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use "cipher out of policy" value instead of invalid group cipher (which
is for the group data frame cipher) and management frame policy
violation (which is used for MFPC/MFPR mismatch).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd with previoiusly implemented wpa_supplicant
functionality to retry DPP Authentication Request/Response and to
iterate over possible negotiation channels.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Not all code paths for management frame RX reporting delivered the
correct frequency for offchannel RX cases. This is needed mainly for
Public Action frame processing in some special cases where AP is
operating, but an exchange is done on a non-operational channel. For
example, DPP Initiator role may need to do this.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The test against use of TKIP was done only in MFP-required
(ieee80211w=2) configuration. Fix this to check the pairwise cipher for
MFP-enabled (ieee80211w=1) case as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf parameter sae_require_pmf=<0/1> can now be used to
enforce negotiation of MFP for all associations that negotiate use of
SAE. This is used in cases where SAE-capable devices are known to be
MFP-capable and the BSS is configured with optional MFP (ieee80211w=1)
for legacy support. The non-SAE stations can connect without MFP while
SAE stations are required to negotiate MFP if sae_require_mfp=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set Sc to 2^16-1 when moving to Accepted state per IEEE Std 802.11-2016,
12.4.8.6.5 (Protocol instance behavior - Confirmed state). This allows
the peer in Accepted state to silently ignore unnecessary
retransmissions of the Confirm message.
Signed-off-by: Jouni Malinen <j@w1.fi>
This implements the behavior described in IEEE Std 802.11-2016,
12.4.8.6.6 (Protocol instance behavior - Accepted state) to silently
discard received Confirm message in the Accepted state if the new
message does not use an incremented send-confirm value or if the special
2^16-1 value is used. This avoids unnecessary processing of
retransmitted Confirm messages.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf parameter sae_sync (default: 5) can now be used to
configure the dot11RSNASAESync value to specify the maximum number of
synchronization errors that are allowed to happen prior to
disassociation of the offending SAE peer.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows external programs to get the average channel utilization.
The average channel utilization is calculated and reported through
STATUS command. Users need to configure chan_util_avg_period and
bss_load_update_period in hostapd config to get the average channel
utilization.
Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
Recalculate the timeout value for each event instead of calculating this
once and then not allowing the timeout configuration to be changed
without fully stopping and restarting the interface.
This allows the bss_load_update_period configuration parameter to be
modified while a BSS continues operating.
Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
Do not update the configuration parameter before having verified the
value to be in the valid range.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
owe_auth_req_process() can return NULL in error cases, but the caller
was not prepared for this. The p pointer cannot be overridden in such
cases since that would result in buffer length (p - buf) overflows. Fix
this by using a temporary variable to check the return value before
overriding p so that the hostapd_sta_assoc() ends up using correct
length for the IE buffer.
Fixes: 33c8bbd8ca ("OWE: Add AP mode handling of OWE with drivers that implement SME")
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to allow a credential to be built for GCMP-256/CCMP-256
networks that do not enable GCMP-128/CCMP-128.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the check against WPA/TKIP only configuration by adding CCMP-256
and GCMP-256 to the list of allowed ciphers. This is needed to allow WPS
to be enabled in AP configurations where neither CCMP-128 nor GCMP-128
are enabled.
Signed-off-by: Shiva Sankar Gajula <sgajula@qti.qualcomm.com>
Previously this stopped only the DPP Authentication instance, but it is
better to clear both PKEX and Authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant was already doing this and hostapd needs to clear
hapd->dpp_auth when completing the exchange in Configurator (GAS server)
role.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
An additional TX status callback could result in processing the DPP
authentication completion another time at least with hostapd. Fix this
by clearing the dpp_auth_ok_on_ack when processing it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Configurator signing its own Connector was previously supported only in
wpa_supplicant. This commit extends that to hostapd to allow an AP
acting as a Configurator to self-configure itself.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This moves the Configurator and Bootstrapping Information data from
struct hostapd_data (per-BSS) to struct hapd_interfaces (per-hostapd
process). This allows the information to be maintained over interface
restarts and shared between interfaces.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These allow external programs to determine supported legacy, HT, and VHT
rates of an interface or a STA.
Signed-off-by: Bhagavathi Perumal S <bperumal@qti.qualcomm.com>
If fils_decrypt_assoc() were to fail on the AP side, the previous
implementation could have continued through the response generation
using left = -1. That could have resulted in unexpected processing if
this value were to be used as the length of the remaining (unencrypted)
IEs. Fix this by not updating left in the failure case.
Fixes: 78815f3dde ("FILS: Decrypt Association Request elements and check Key-Auth (AP)")
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that nothing unexpected happened with EAPOL-Key Key MIC
calculation when transmitting EAPOL-Key frames from the Authenticator.
This should not be able to happen in practice, but if if it does, there
is no point in sending out the frame without the correct Key MIC value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
With the AP proto configured being WPA/RSN and SME in the
driver, the previous implementation in hostapd is to not
process hostapd_notif_assoc() due to "No WPA/RSN IE from STA",
if the (Re)Association Request frame is without the WPA/RSN IEs.
Enhance that to disassociate such station provided the AP is not using
WPS.
Signed-off-by: Hu Wang <huw@codeaurora.org>
This allows external applications to get event indication for Probe
Request frames. Extend ctrl iface cmd "ATTACH" to enable this event on
per-request basis. For example, user has to send ctrl iface cmd "ATTACH
probe_rx_events=1" to enable the Probe Request frame events.
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
The new conf={sta,ap}-{sae,psk-sae} parameter values can now be used to
specify that the legacy configuration object is for SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows DPP to be used for enrolling credentials for SAE networks in
addition to the legacy PSK (WPA-PSK) case. In addition, enable FT-PSK
and FT-SAE cases automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to allow more invalid attribute values to be written
into Peer Discovery Request/Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the build include SHA384, use that to derive GTK from GMK. In
addition, add more random bytes bytes to the PRF-X() context data for
longer GTK to reduce dependency on the randomness of the GMK.
GMK is 256 bits of random data and it was used with SHA256, so the
previous design was likely sufficient for all needs even with 128 bits
of additional randomness in GTK derivation. Anyway, adding up to 256
bits of new randomness and using SHA384 can be helpful extra protection
particularly for the cases using GCMP-256 or CCMP-256 as the group
cipher.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter group_cipher can now be used to
override the automatic cipher selection based on enabled pairwise
ciphers. It should be noted that selecting an unexpected group cipher
can result in interoperability issues and this new capability is mainly
for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this command stopped listen operation immediately, but if
there was an ongoing authentication exchange, a new listen operation was
started. This is not really expected behavior, so stop the
authentication exchange first with this command to avoid restarting
listen operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new role=either parameter can now be used with DPP_AUTH_INIT to
indicate that the initiator can take either the Configurator or Enrollee
role.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant to iterate over all available channels from
the intersection of what the peer indicates and the local device
supports when initiating DPP Authentication. In addition, retry DPP
Authentication Request frame up to five times if no response is
received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is an initial step in allowing non-operating channel operations
with DPP when hostapd is the Responder. For now, this is only used for
specifying role=configurator/enrollee and qr=mutual cases similarly to
the wpa_supplicant configuration for in Responder role. Request to use a
non-operating channel will be rejected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add limit on number of failed attempts that could have used PKEX code.
If the limit (5) is reached, drop the PKEX state (including the code)
and report this on the control interface to indicate that a new code
needs to be entered due to possible attack.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Clean up the pending PKEX exchange if Commit-Reveal Request processing
indicates a mismatch in the PKEX code. Previously, the this case was
silently ignored and the session was left in pending state that
prevented new PKEX exchanges from getting initated. Now, a new attempt
is allowed to be initiated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Report mismatching finite cyclic group with PKEX Exchange Response using
STATUS_BAD_GROUP and provide more detailed error report over the control
interface on the peer device when this happens.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previously used WLAN_REASON_MICHAEL_MIC_FAILURE (14) value as a
response to Authentication frame or (Re)Association Request frame is not
correct since the resp value is encoded in the Status Code (not Reason
Code) field. Status Code 14 is WLAN_STATUS_UNKNOWN_AUTH_TRANSACTION
which is really what this value would have meant in the response frames.
There is no Michael MIC failure status code, so have to use the generic
"Unspecified failure" (1) reason code for these cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Indicate to upper layers if PKEX Commit-Reveal Request frame AES-SIV
decryption fails. That is a likely sign of the PKEX code mismatch
between the devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Build breakage was introduced by commit
d8afdb210e ('Allow EAPOL-Key messages 1/4
and 3/4 to be retransmitted for testing') for some
CONFIG_TESTING_OPTIONS=y builds without CONFIG_IEEE80211W=y.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
This provides access to the Minimum/Maximum Transmit Power Capabilitie
fileds (the nominal minimum/maximum transmit power with which the STA
is capable of transmitting in the current channel; signed integer in
units of decibels relative to 1 mW).
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
Handle OWE DH exchange and key setup when processing the association
event from a driver that implements AP SME.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While most places using this should be for cases where the hw_features
functionality is required, there seem to be some paths that are getting
exposed in new OWE related operations where that might not be the case.
Add explicit NULL pointer checks to avoid dereferencing the pointer if
it is not set when operating with driver wrappers that do not provide
sufficient information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Normally, WNM-Sleep Mode exit with management frame protection
negotiated would result in the current GTK/IGTK getting added into the
WNM-Sleep Mode Response frame. Some station implementations may have a
vulnerability that results in GTK/IGTK reinstallation based on this
frame being replayed. Add a new hostapd configuration parameter that can
be used to disable that behavior and use EAPOL-Key frames for GTK/IGTK
update instead. This would likely be only used with
wpa_disable_eapol_key_retries=1 that enables a workaround for similar
issues with EAPOL-Key. This is related to station side vulnerabilities
CVE-2017-13087 and CVE-2017-13088. To enable this AP-side workaround,
set wnm_sleep_mode_no_keys=1.
Signed-off-by: Jouni Malinen <j@w1.fi>
When strict group rekeying is in effect, every station that leaves will
cause a rekeying to happen 0.5 s after leaving. However, if a lot of
stations join/leave, the previous code could postpone this rekeying
forever, since it always re-registers the handling with a 0.5 s timeout.
Use eloop_deplete_timeout() to address that, only registering the
timeout from scratch if it wasn't pending.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to test the WoWLAN GTK rekeying KRACK mitigation, add a
REKEY_GTK hostapd control interface command that can be used at certain
points of the test.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the Initiator to request a different channel to be used for DPP
Authentication and DPP Configuration exchanges. This commit adds support
for this in wpa_supplicant with the optional neg_freq=<freq in MHz>
parameter in DPP_AUTH_INIT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Both the DPP-TX and DPP-TX-STATUS events are provided.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that dpp_check_attrs() takes care of verifying that no attributes
are after the Wrapped Data attribute, the duplicated checks in hostapd
and wpa_supplicant side of the implementation can be removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Build breakage was introduced by commit
16579769ff ('Add testing functionality for
resetting PN/IPN for configured keys') for some CONFIG_TESTING_OPTIONS=y
builds.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The hostapd bss_transition parameter was previously used to control
advertisement of BSS Transition Management support, but it was not used
when processing BSS Transition Management Query/Response frames. Add an
explicit check during frame processing as well so that any misbehaving
station is ignored. In addition to bss_transition=1, allow mbo=1 to be
used to mark the functionality enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The hostapd wnm_sleep_mode parameter was previously used to control
advertisement of WNM-Sleep Mode support, but it was not used when
processing a request to use WNM-Sleep Mode. Add an explicit check during
request processing as well so that any misbehaving station is ignored.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows hostapd testing functionality to be forced to send out a
plaintext EAPOL-Key frame with the RESEND_* command. That can be useful
in seeing how the station behaves if an unencrypted EAPOL frame is
received when TK is already configured.
This is not really perfect since there is no convenient way of sending
out a single unencrypted frame in the current nl80211 design. The
monitor interface could likely still do this, but that's not really
supposed to be used anymore. For now, clear and restore TK during this
operation. The restore part is not really working correctly, though,
since it ends up clearing the TSC value on the AP side and that shows up
as replay protection issues on the station. Anyway, this is sufficient
to generate sniffer captures to analyze station behavior.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a new hostapd configuration parameter
wpa_disable_eapol_key_retries=1 that can be used to disable
retransmission of EAPOL-Key frames that are used to install
keys (EAPOL-Key message 3/4 and group message 1/2). This is
similar to setting wpa_group_update_count=1 and
wpa_pairwise_update_count=1, but with no impact to message 1/4
retries and with extended timeout for messages 4/4 and group
message 2/2 to avoid causing issues with stations that may use
aggressive power saving have very long time in replying to the
EAPOL-Key messages.
This option can be used to work around key reinstallation attacks
on the station (supplicant) side in cases those station devices
cannot be updated for some reason. By removing the
retransmissions the attacker cannot cause key reinstallation with
a delayed frame transmission. This is related to the station side
vulnerabilities CVE-2017-13077, CVE-2017-13078, CVE-2017-13079,
CVE-2017-13080, and CVE-2017-13081.
This workaround might cause interoperability issues and reduced
robustness of key negotiation especially in environments with
heavy traffic load due to the number of attempts to perform the
key exchange is reduced significantly. As such, this workaround
is disabled by default (unless overridden in build
configuration). To enable this, set the parameter to 1.
It is also possible to enable this in the build by default by
adding the following to the build configuration:
CFLAGS += -DDEFAULT_WPA_DISABLE_EAPOL_KEY_RETRIES=1
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface commands "RESEND_M1 <addr>" and
"RESEND_M3 <addr>" can be used to request a retransmission of the 4-Way
Handshake messages 1/4 and 3/4 witht he same or modified ANonce (in M1).
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd control interface command "RESEND_GROUP_M1 <addr>" can
be used to request a retransmission of the Group Key Handshake message
1/2 for the current GTK.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation ended up starting a new EAPOL-Key 4-way
handshake if the STA were to attempt to perform another association.
This resulted in immediate disconnection since the PTK was not ready for
configuring FILS TK at the point when EAPOL-Key msg 1/4 is sent out.
This is better than alloing the association to continue with the same TK
reconfigured, but not really ideal.
Address this potential sequence by not starting a new 4-way handshake on
the additional association attempt. Instead, allow the association to
complete, but do so without reconfiguring the TK to avoid potential
issues with PN reuse with the same TK.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows ext_mgmt_frame_handling=1 cases with hostapd to process TX
status events based on external processing. This is useful for increased
test coverage of management frame processing.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Authenticator state machine path for PTK rekeying ended up bypassing
the AUTHENTICATION2 state where a new ANonce is generated when going
directly to the PTKSTART state since there is no need to try to
determine the PMK again in such a case. This is far from ideal since the
new PTK would depend on a new nonce only from the supplicant.
Fix this by generating a new ANonce when moving to the PTKSTART state
for the purpose of starting new 4-way handshake to rekey PTK.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not reinstall TK to the driver during Reassociation Response frame
processing if the first attempt of setting the TK succeeded. This avoids
issues related to clearing the TX/RX PN that could result in reusing
same PN values for transmitted frames (e.g., due to CCM nonce reuse and
also hitting replay protection on the receiver) and accepting replayed
frames on RX side.
This issue was introduced by the commit
0e84c25434 ('FT: Fix PTK configuration in
authenticator') which allowed wpa_ft_install_ptk() to be called multiple
times with the same PTK. While the second configuration attempt is
needed with some drivers, it must be done only if the first attempt
failed.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
The new sae_password hostapd configuration parameter can now be used to
set the SAE password instead of the previously used wpa_passphrase
parameter. This allows shorter than 8 characters and longer than 63
characters long passwords to be used. In addition, this makes it
possible to configure a BSS with both WPA-PSK and SAE enabled to use
different passphrase/password based on which AKM is selected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd configuration parameter owe_groups can be used to
specify a subset of the allowed DH groups as a space separated list of
group identifiers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This additional field was added to DPP Public Action frames in DPP tech
spec v0.2.3 to support cryptographic agility in the future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The owe_transition_bssid and owe_transition_ssid parameters can now be
replace with owe_transition_ifname to clone the BSSID/SSID information
automatically in case the same hostapd process manages both the OWE and
open BSS for transition mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends OWE support in hostapd to allow DH groups 20 and 21 to be
used in addition to the mandatory group 19 (NIST P-256).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is not normally done in RSN, but RFC 8110 seems to imply that AP
has to include OWE AKM in the RSNE within these frames. So, add the RSNE
to (Re)Association Response frames when OWE is being negotiated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new owe_transition_bssid and owe_transition_ssid parameters can be
used to configure hostapd to advertise the OWE Transition Mode element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Replace vendor-specific elements for HE capabilities and HE operation
elements with the P802.11ax defined element values. This version is
based on P802.11ax/D1.4.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These allow external programs to fetch the TX and RX rate information
and signal strength for a specific STA through the hostapd control
interface command "STA <addr>". The values of these attributes are
filled in the response of nl80211 command NL80211_CMD_GET_STATION.
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
In fils_hlp_finish_assoc() the station is already added to the
driver so it is not needed to check the 'added_unassociated'
flag.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add checking for NULL req_ies when FILS processing a driver ASSOC event
in hostapd_notif_assoc(). This was already done in number of old code
paths, but the newer FILS path did not handle this. Though, it is
unlikely that this code path would be reachable in practice since this
is all within sta->auth_alg == WLAN_AUTH_FILS_* check.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new psk=<hexdump> can be used as an alternative to pass=<passphrase>
when configuring the DPP Configurator with a legacy network parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These control interface event messages can be used to allow hostapd AP
to be configured for legacy WPA2-Personal configuration with DPP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While the Suite B AKM is not really going to be used with CCMP-128 or
GCMP-128 cipher, this corner case could be fixed if it is useful for
some testing purposes. Allow that special case to skip the HMAC-SHA1
check based on CCMP/GCMP cipher and use the following AKM-defined check
instead.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This part is missing from IEEE Std 802.11ai-2016, but the lack of DHss
here means there would not be proper PFS for the case where PMKSA
caching is used with FILS SK+PFS authentication. This was not really the
intent of the FILS design and that issue was fixed during REVmd work
with the changes proposed in
https://mentor.ieee.org/802.11/dcn/17/11-17-0906-04-000m-fils-fixes.docx
that add DHss into FILS-Key-Data (and PTK, in practice) derivation for
the PMKSA caching case so that a unique ICK, KEK, and TK are derived
even when using the same PMK.
Note: This is not backwards compatible, i.e., this breaks PMKSA caching
with FILS SK+PFS if only STA or AP side implementation is updated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11ai-2016 had missed a change in the Pairwise key hierarchy
clause (12.7.1.3 in IEEE Std 802.11-2016) and due to that, the previous
implementation ended up using HMAC-SHA-1 -based PMKID derivation. This
was not really the intent of the FILS design and that issue was fixed
during REVmd work with the changes proposed in
https://mentor.ieee.org/802.11/dcn/17/11-17-0906-04-000m-fils-fixes.docx
that change FILS cases to use HMAC-SHA-256 and HMAC-SHA-384 based on the
negotiated AKM.
Update the implementation to match the new design. This changes the
rsn_pmkid() function to take in the more generic AKMP identifier instead
of a boolean identifying whether SHA256 is used.
Note: This is not backwards compatible, i.e., this breaks PMKSA caching
based on the initial ERP key hierarchy setup if only STA or AP side
implementation is updated. PMKSA caching based on FILS authentication
exchange is not impacted by this, though.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The "FILS: No pending HLP DHCP exchange with hw_addr" debug message was
missing a space before the following MAC address, so add that there to
make the message more readable.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new sae_commit_override=<hexdump> parameter can be used to force
hostapd to override SAE commit message fields for testing purposes. This
is included only in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow hostapd to be configured to perform SAE reflection attack for SAE
testing purposes with sae_reflection_attack=1 configuration parameter.
This is included only in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add PMKID into EAPOL-Key 1/4 when using SAE and fix the PMK-from-PMKSA
selection in some cases where PSK (from passphrase) could have been
used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DPP tech spec changed the contents of these frames by replacing the
public key hash attributes with a Transaction ID attribute that gets
copied from the request to the response to identify the transaction in a
simpler manner.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, CONFIG_WNM enabled build that supports WNM for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode WNM is required and there is no need for AP mode WNM.
Add support to differentiate between station mode WNM and AP mode
WNM in wpa_supplicant builds by adding CONFIG_WNM_AP that should be
used when AP mode WNM support is required in addition to station mode
WNM. This allows binary size to be reduced for builds that require
only the station side WNM functionality.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add OCE IE in Beacon, Probe Response, and (Re)Association Response
frames if OCE is enabled in the configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In case of incorrect HT40 configuration as part of an attempt to create
a 80 MHz AP, iface->conf->vht_oper_centr_freq_seg0_idx and
iface->conf->vht_oper_centr_freq_seg1_idx are zero'ed, but
iface->conf->vht_oper_chwidth remains VHT_CHANWIDTH_80MHZ. This causes
the logic in dfs_get_start_chan_idx to fail.
Fix this by setting iface->conf->vht_oper_chwidth to
VHT_CHANWIDTH_USE_HT when zero'ing the center frequency parameters.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
dpp.h file requires openssl in order to compile, which breaks
compilation on systems without it.
Move DPP_OUI_TYPE to ieee802_11_defs.h and don't include dpp.h when
not really needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
hostapd did not add a new PMKSA cache entry when FILS shared key
authentication was used, i.e., only the initial full authentication
resulted in a PMKSA cache entry being created. Derive the PMKID for the
ERP case as well and add a PMKSA cache entry if the ERP exchange
succeeds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The EAP message included in FILS Wrapped Data from the non-AP STA to the
AP is EAP-Initiate/Re-auth.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends the hostapd control interface to support the
DPP_BOOTSTRAP_INFO command that was recently added for wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The default value for GTK rekeying period was previously hardcoded to
600 seconds for all cases. Leave that short value only for TKIP as group
cipher while moving to the IEEE 802.11 default value of 86400 seconds
(once-per-day) for CCMP/GCMP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This updates the previously copied implementation to be up-to-date with
the more recent wpa_supplicant changes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow hostapd to initiate and respond with PKEX bootstrapping similarly
to how this was implemented in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend hostapd configuration to include parameters needed for the DPP
AKM: dpp_connector, dpp_netaccesskey, dpp_netaccesskey_expiry,
dpp_csign, dpp_csign_expiry.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external programs to generate and add PMKSA cache entries
into hostapd. The main use for this is to run external DPP processing
(network introduction) and testing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds DPP bootstrapping, authentication, and configuration into
hostapd similarly to how the design was integrated in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd processes a received 20/40 BSS Coexistence management frame, but
if no separate callbacks are registered for handling Public Action
frames it eventually sends a reply with MSB of category code set to 1
thinking that the received frame is an invalid frame. This could happen
based on whether hostapd was built and enabled with functionality using
the callback functions.
Fix this by explicitly returning 1 from the function when the 20/40 BSS
Coexistence Management frame is processed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new acs_exclude_dfs=1 parameter can be used to request hostapd to
exclude all DFS channels from ACS consideration. This is mainly of use
for cases where the driver supports DFS channels, but for some reason a
non-DFS channel is desired when using automatic channel selection.
Previously, the chanlist parameter could have been used for this, but
that required listing all the acceptable channels. The new parameter
allows this to be done without such a list.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is to comply with uniform spreading requirement for ETSI domain
(section 4.7.2.7 in EN 301 893 - V1.8.1). ETSI uniform spreading
requires equal probability for the usable channels. The previous channel
selection logic after a radar detection did not fully comply with the
uniform spreading requirement for the domain by ignoring DFS channels.
Consider DFS channels also during channel selection when the current DFS
domain is ETSI.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Derive PMK-R0 and the relevant key names when using FILS authentication
for initial FT mobility domain association.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends fils_pmk_to_ptk() to allow FILS-FT to be derived. The
callers do not yet use that capability; i.e., actual use will be added
in separate commits.
Signed-off-by: Jouni Malinen <j@w1.fi>
The conditional gSTA and gAP (DH public keys) were not previously
included in Key-Auth derivation, but they are needed for the PFS case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Enable use of FT RRB without configuring each other AP locally. Instead,
broadcast messages are exchanged to discover APs within the local
network.
When an R0KH or R1KH is discovered, it is cached for one day.
When a station uses an invalid or offline r0kh_id, requests are always
broadcast. In order to avoid this, if r0kh does not reply, a temporary
blacklist entry is added to r0kh_list.
To avoid blocking a valid r0kh when a non-existing pmk_r0_name is
requested, r0kh is required to always reply using a NAK. Resend requests
a few times to ensure blacklisting does not happen due to small packet
loss.
To free newly created stations later, the r*kh_list start pointer in
conf needs to be updateable from wpa_auth_ft.c, where only wconf is
accessed.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This adds a counter and adds sequence numbering to FT RRB packets. The
sequence number is checked against r0kh/r1kh sequence number cache.
Special attention is needed in case the remote AP reboots and thus loses
its state. I prefer it to recover automatically even without synchronized
clocks. Therefore an identifier called dom is generated randomly along the
initial sequence number. If the dom transmitted does not match or the
sequence number is not in the range currently expected, the sender is asked
for a fresh confirmation of its currently used sequence numbers. The packet
that triggered this is cached and processed again later.
Additionally, in order to ensure freshness, the remote AP includes an
timestamp with its messages. It is then verified that the received
messages are indeed fresh by comparing it to the older timestamps
received and the time elapsed since then. Therefore FT_RRB_TIMESTAMP is
no longer needed.
This assigns new OUI 00:13:74 vendor-specific subtype 0x0001 subtypes:
4 (SEQ_REQ) and 5 (SEQ_RESP).
This breaks backward compatibility, i.e., hostapd needs to be updated
on all APs at the same time to allow FT to remain functional.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Convert FT RRB into a new TLV based format. Use AES-SIV as AEAD cipher
to protect the messages.
This needs at least 32 byte long keys. These can be provided either
by a config file change or letting a KDF derive the 32 byte key used
from the 16 byte key given.
This breaks backward compatibility, i.e., hostapd needs to be updated on
all APs at the same time to allow FT to remain functional.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Replace the previously used extension of IEEE 802.11 managed Ethertype
89-0d (originally added for Remote Request/Response in IEEE 802.11r)
with Ethertype 88-b7 (OUI Extended EtherType) for FT inter-AP
communication. The new design uses a more properly assigned identifier
for the messages.
This assigns the OUI 00:13:74 vendor-specific subtype 0x0001 for the new
hostapd AP-to-AP communication purposes. Subtypes 1 (PULL), 2 (RESP),
and 3 (PUSH) are also assigned in this commit for the R0KH-R1KH
protocol.
This breaks backward compatibility, i.e., hostapd needs to be updated on
all APs at the same time to allow FT to remain functional.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Commit 941caed980 ('MBO: Add MBO
ANQP-element processing on AP') changed the design by using the
rx_anqp_vendor_specific() function to process all ANQP vendor specific
elements. However, the caller for this was within ifdef CONFIG_HS20
block. Fix this by calling the function even in CONFIG_HS20=y is not
included in the build. This fixes CONFIG_MBO=y builds without
CONFIG_HS20=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
When starting AP in HT40 mode and both HT40+ and HT40- options are
specified in hostapd.conf, select a valid secondary channel for the AP
automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow this function to be called from outside ieee802_11.c and with the
final steps replaced through a callback function.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This function does not need the frame header, so pass in only the IE
area to make it easier to share this for driver-based AP SME handling.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is used with partial AP SME in driver cases to enable FILS
association (AES-SIV) processing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to add more parameters without having to change the
callback function prototype.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
MDE was already added with RSNE, but FTE needed to be added to the FILS
Authentication frame for the FT initial mobility domain association
using FILS authentication case.
Signed-off-by: Jouni Malinen <j@w1.fi>
With AP-AP communication, when hapd0 sends a packet, hapd1 can receive
it immediately and send a response. But hapd0 will only read and process
the response after it has returned from the sending context, that is
entered eloop again. So one does not need to consider the RX function of
the reply to run for the request sending hapd before the send calling
function has returned.
Previously, with intra-process communication, the packet is not
scheduled through eloop. Thus the RX handler of the reply might be run
while the sending context of the original request has not returned.
This might become problematic, e.g., when deferring a management frame
processing until an RRB response is received and then have the request
restarted and finished before the original request handling has been
stopped.
I'm not aware of any concrete bug this is currently triggering but came
across it while thinking of FT RRB AP-AP sequence numbering.
I think the non-eloop scheduling approach might be error-prone and thus
propose to model it more closely to the way the message would be
received from a socket. Additionally, this ensures that the tests model
AP-AP communication more closely to real world.
Solution: queue these packets through eloop.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
With multiple interface like AP and station which is already
associated to some other AP, when we try to do channel switch
for the AP mode (different from the operation channel support of
station) and if the AP channel switch fails continously (including
the fallback channel switch), results in a crash due to NULL pointer
dereference. This is because hostapd_deinit_driver() assigns the
driver context (drv_priv) to NULL as we are not able to bring up
the interface with a new channel
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
This fixes the following compiler warning:
wpa_auth.c:4249:34: error: address of array 'a->conf.fils_cache_id'
will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds an option to configure hostapd to enable use of perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime configuration parameter fils_dh_group is used to enable this
by specifying which DH group to use. For example, fils_dh_group=19 would
allow FILS SK PFS to be used with a 256-bit random ECP group.
Signed-off-by: Jouni Malinen <j@w1.fi>
draft-harkins-owe-07.txt does not specify these parameters, so need to
pick something sensible to use for the experimental implementation. The
Suite B 128-bit level AKM 00-0F-AC:11 has reasonable parameters for the
DH group 19 case (i.e., SHA256 hash), so use it for now. This can be
updated if the OWE RFC becomes clearer on the appropriate parameters
(KEK/KCK/MIC length, PRF/KDF algorithm, and key-wrap algorithm).
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds AP side processing for OWE Diffie-Hellman Parameter element in
(Re)Association Request frame and adding it in (Re)Association Response
frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the GAS server to process MBO ANQP-elements and reply to a
query for the Cellular Data Connection Preference (if configured). The
new configuration parameter mbo_cell_data_conn_pref can be used to set
the value (0, 1, or 255) for the preference to indicate.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
As FCC DFS requirement does not explicitly mention about the validity of
the (pre-)CAC when channel is switched, it is safe to assume that the
pre-CAC result will not be valid once the CAC completed channel is
switched or radar detection is not active on the (CAC completed) channel
within a time period which is allowed (10 seconds - channel switch time)
as per FCC DFS requirement.
Use the new driver event to allow the driver to notify expiry of the CAC
result on a channel. Move the DFS state of the channel to 'usable' when
processing pre-CAC expired event. This means any future operation on
that channel will require a new CAC to be completed. This event is
applicable only when DFS is not offloaded to the kernel driver.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
When DFS channel state is shared across multiple radios on the system it
is possible that a CAC completion event is propagated from other radio
to us. When in enabled state, do not proceed with setup completion upon
processing CAC completion event with devices where DFS is not offloaded,
when in state other than enabled make sure the configured DFS channel is
in available state before start the AP.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
This leads to cleaner code overall, and also reduces the size
of the hostapd and wpa_supplicant binaries (in hwsim test build
on x86_64) by about 2.5 and 3.5KiB respectively.
The mechanical conversions all over the code were done with
the following spatch:
@@
expression SIZE, SRC;
expression a;
@@
-a = os_malloc(SIZE);
+a = os_memdup(SRC, SIZE);
<...
if (!a) {...}
...>
-os_memcpy(a, SRC, SIZE);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was possible to hit a double-free on the l2_packet socket if
initialization of DHCP/NDISC snoop failed on a hostapd interface that
had previously had those enabled successfully. Fix this by clearing the
l2_packet pointers during deinit.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd.conf parameter country3 can now be used to configure the
third octet of the Country String that was previously hardcoded to ' '
(= 0x20).
For example:
All environments of the current frequency band and country (default)
country3=0x20
Outdoor environment only
country3=0x4f
Indoor environment only
country3=0x49
Noncountry entity (country_code=XX)
country3=0x58
IEEE 802.11 standard Annex E table indication: 0x01 .. 0x1f
Annex E, Table E-4 (Global operating classes)
country3=0x04
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When getting the channel number from a frequency, all supported modes
should be checked rather than just the current mode. This is needed when
hostapd switches to a channel in different band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The __FAVOR_BSD macro was previously used in netinet/udp.h to select
between two different names of the variables in struct udphdr. Define
that to force the versions with the uh_ prefix. In addition, use the
same style consistently within fils_hlp.c.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new broadcast_deauth parameter can be used to disable sending of the
Deauthentication frame whenever AP is started or stopped. The default
behavior remains identical to the past behavior (broadcast_deauth=1).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 01e2231fdc ('hostapd: Skip some
configuration steps for mesh cases') removed some operations based on
hapd->iface->mconf being NULL. This was within #ifdef CONFIG_MESH, so it
should not impact hostapd, but it can impact AP mode with
wpa_supplicant. That does not sound intentional, so make these
conditional on hapd->conf->mesh being enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows PMKSA cache entries to be shared between all the BSSs
operated by the same hostapd process when those BSSs use the same FILS
Cache Identifier value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE 802.11ax HE changes to include HE IEs in Beacon and Probe Response
frames. These elements are using vendor specific forms for now since the
IEEE 802.11ax draft is not yet finalized and the element contents is
subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add IEEE 802.11ax definitions for config, IEEE structures, and
constants. These are still subject to change in the IEEE process.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Let mesh STA A be a STA which has config disable_ht=0 and disable_vht=1.
Let mesh STA B be a STA which has config disable_ht=0 and disable_vht=0.
The mesh STA A and B was connected.
Previously, the mesh STA A sent frame with VHT rate even though its VHT
was disabled. This commit fixes the issue by checking the local BSS VHT
configuration.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Let mesh STA A be a STA which has config disable_ht=1.
Let mesh STA B be a STA which has config disable_ht=0.
The mesh STA A and B was connected.
Previously, the mesh STA A sent frame with HT rate even though its HT
was disabled. This commit fixes the issue by checking the local BSS HT
configuration.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
While the FILS authentication cases were already using the proper PMK
length (48 octets instead of the old hardcoded 32 octet), the initial
association case had not yet been updated to cover the new FILS SHA384
AKM and ended up using only a 32-octet PMK. Fix that to use 48-octet PMK
when using FILS SHA384 AKM.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, any potential (even if very unlikely) local operation error
was ignored. Now these will result in aborting the negotiation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The url argument to ieee802_11_send_bss_trans_mgmt_request() was
hardcoded to NULL in the only caller, so this code cannot be reached.
wnm_send_bss_tm_req() construct the same frame with more generic
parameters, including option for including the URL, so
ieee802_11_send_bss_trans_mgmt_request() can be simplified.
Signed-off-by: Jouni Malinen <j@w1.fi>
The length of the WNM-Sleep element was not verified before using it.
This could result in reading the subfields in this element (total of
four octets) beyond the end of the buffer. Fix this by ignoring the
element if it is not long enough to contain all the subfields.
Signed-off-by: Jouni Malinen <j@w1.fi>
The struct wpa_stsl_negotiation seemed to have been for some kind of
tracking of state of PeerKey negotiations within hostapd. However,
nothing is actually adding any entries to wpa_auth->stsl_negotiations or
using this state. Since PeerKey does not look like something that would
be deployed in practice, there is no justification to spend time on
making this any more complete. Remove the dead code now instead of
trying to figure out what it might be used for.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the int medium_time variable to overflow, so use a
64-bit unsigned integer to get a large enough value for the
multiplication.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to maintain different return paths for STA being
completely not present and not authorized, so merge these into a single
case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>