There is a chance that wpa_supplicant may get killed during
the time it is writing config file. If this happens, user
information like SSIDs and passwords can be lost forever.
This change works around that by writing config to a
temporary file and then renaming the file to the correct name.
Signed-off-by: Vinit Deshpande <vinitd@google.com>
We should not enable HT if WEP or TKIP is configured.
Without the patch and WEP configuration we will get message:
Association request to the driver failed
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Previously, a channel with even a single scan/survey result missing
information was skipped in ACS. This may not be desirable in cases when
multiple scan iterations are used (which is the case by default in
hostapd). Instead, use all channels that provided at least one complete
set of results. Calculate the average interference factor as an average
of the iterations that did provide complete values.
This seems to help with some cases, e.g., when ath9k may not be able to
report the noise floor for all channels from the first scan iteration
immediately after the driver has been loaded, but then returns it for
all other scan iterations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new acs_chan_bias configuration parameter is a space-separated list
of <channel>:<bias> pairs. It can be used to increase (or decrease) the
likelihood of a specific channel to be selected by the ACS algorithm.
The total interference factor for each channel gets multiplied by the
specified bias value before finding the channel with the lowest value.
In other words, values between 0.0 and 1.0 can be used to make a channel
more likely to be picked while values larger than 1.0 make the specified
channel less likely to be picked. This can be used, e.g., to prefer the
commonly used 2.4 GHz band channels 1, 6, and 11 (which is the default
behavior on 2.4 GHz band if no acs_chan_bias parameter is specified).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The interference factors for adjacent 2.4 GHz channels were summed
together without doing any kind of weighted average on them. This
resulted in the channels at the band edges getting undue preference due
to only including interference factors from three channels vs. five for
the channels in the middle of the band.
While it is somewhat unclear whether the design here was supposed to
count overlapping channels together in this way or whether that is
already covered in channel survey results, it is clear that this summing
of three to five values together and then comparing the sum rather than
average of some kind gives too much preference to the channels at the
edges of the band by assuming that there is no interference whatsoever
outside the band.
Use weighted average of the interference factors rather than a sum from
different number of values. For now, the adjacent 2.4 GHz channels get
weight of 0.85 (1.0 for the main channel itself) and the neighboring
channels to those adjacent ones get 0.55 weight. Band-edge channels are
handled in a way that takes average over the channels that were actually
considered instead of assuming zero interference from neighboring bands.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
1. Modify discovery_stop to use global control interface when calling
P2P_FLUSH.
2. Modify p2p_listen_and_offchannel_tx to use the global control
interface when waiting for P2P PD event.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Some of the tests used p2p_dev_addr() that can be different from
own_addr() if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Some of the tests used p2p_dev_addr() that can be different from
own_addr() if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
The test used p2p_dev_addr() that can be different from own_addr()
if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
The test used p2p_dev_addr() that can be different from own_addr()
if a dedicated P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Fix the destination address that is sent in the WNM-Notification to be
the BSS address opposed to the P2P address.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
This is needed for cases that the group interface differs from the main
interface, i.e., when a dedicated P2P Device interface is used.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When the 'SET' command is used to configure parameters related to P2P
operation use the global control interface and not the per interface one
as otherwise the setting will only have effect on the interface and will
work if a dedicated P2P_DEVICE is used.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Once the connection is established need to call group_form_result() on
the invited device, as otherwise the group interface name is not updated
and the connectivity test is done with the main interface instead of the
group interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
These are far from perfect since timing is quite difficult to match for
the case that behaved incorrectly. Anyway, it looks loke
p2p_service_discovery_peer_not_listening was able to hit the error now
and then, so this should be sufficient as a regression test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If p2p_find_timeout triggers after starting SD but before getting TX
status for send action, unwanted search could get triggered again when
TX status arrives though p2p_find_timeout moved the state to P2P_IDLE by
then. p2p_continue_find() would then move the state to P2P_SEARCH again.
Do not trigger the find operation from this context if state is
P2P_IDLE to avoid this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is going to be required for OpenSSL 1.1.0 which makes the SSL
structure opaque. Older versions starting from OpenSSL 1.0.1 include
this function, so start using it now based on OPENSSL_VERSION_NUMBER.
Signed-off-by: Jouni Malinen <j@w1.fi>
OpenSSL 0.9.8 and newer includes SSL_CTX_get_cert_store() and
SSL_CTX_set_cert_store() helper functions, so there is no need to
dereference the SSL_CTX pointer to cert ssl_ctx->cert_store. This helps
in working with the future OpenSSL 1.1.0 release that makes the SSL_CTX
structure opaque.
Signed-off-by: Jouni Malinen <j@w1.fi>
Include actual extended listen period in the test and confirm that the
device was available on a social channel during such period by using
non-social operating channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not claim to change the Listen channel in a debug message when
previously configured channel prevents this. In addition, fix a typo in
another related debug print.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter has been available for more than just testing purposes,
i.e., OBSS scanning has already been used to enable 20-to-40 MHz channel
changes on 2.4 GHz.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If OBSS scan interval is not set, the AP must not schedule a timeout to
restore 40 MHz operation immediately after having moved to a 20 MHz
channel based on an unsolicited co-ex report. Fix this by scheduling the
timeout only if obss_interval is non-zero.
Since we do not currently support AP doing OBSS scans after the initial
BSS setup, this means practically that 40-to-20 MHz transition is
allowed, but 20-to-40 MHz is not with obss_interval=0. The latter gets
enabled if obss_interval is set to a non-zero value so that associated
STAs can take care of OBSS scanning.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This test case is modifying the list of enabled config_method values and
needs to restore "p2ps" option that is included by default. Without
this, P2PS executed after dbus_get_set_wps could fail.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The pending interface created during provision discovery should
not be removed on stopping p2p_find. This pending interface has
to be used after completing GO negotiation. Earlier the pending
interface is created just before GO negotiation so there was no
problem.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_timeout_prov_disc_req is getting triggered in P2P_IDLE,
P2P_SEARCH and P2P_LISTEN_ONLY states. Retry logic should not be
limited to only P2P_IDLE state.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to allow P2PS related new control interface commands to
be redirected for proper context processing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
During service discovery if P2P_FIND times out, P2P_FIND_STOPPED event
is sent to upper layers to allow follow up P2P_FIND commands. This needs
to be done also in case an SD was in progress during the find operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If P2PS config method is used for provisioning, upon forming a new GO,
start WPS registrar for the provisioned peer automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This introduces a P2P module callback function that will be used to
create the pending P2PS group after sending PD Response and receiving
ACK status for it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When the peer device is trying to form a new group despite having
old persistent group with same roles, remove the stale persistent
group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant control interface commands
P2P_ASP_PROVISION and P2P_ASP_PROVISION_RESP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
