The previously used single TOD policy was split into two policies:
TOD-STRICT and TOD-TOFU. Report these separately in the
CTRL-EVENT-EAP-PEER-CERT events (tod=1 for TOD-STRICT and tod=2 for
TOD-TOFU).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed for the drivers implementing SME to include the PMKID in
the Association Request frame directly following SAE authentication.
This commit extends the commit d2b2083843 ("SAE: Allow PMKID to be
added into Association Request frame following SAE") for drivers with
internal SME that use the external authentication mechanism.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
pending_bssid is cleared in the connected state and thus is not valid if
SAE authentication is done to a new BSSID when in the connected state.
Hence use the BSSID from ext_auth_bssid while configuring the PMK for
the external authentication case. This is required for roaming to a new
BSSID with driver-based-SME while the SAE processing happens with
wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
A new DH public key is sent through this interface to the driver after
every successful connection/roam to a BSS. This helps to do OWE roaming
to a new BSS with drivers that implement SME/MLME operations during
roaming.
This updated DH IEs are added in the subsequent (Re)Association Request
frame sent by the station when roaming. The DH IE from the roamed AP is
given to wpa_supplicant in the roam result event. wpa_supplicant shall
further process these DH IEs to generate the PMK for the 4-way
handshake.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update Connection Params is intended for drivers that implement
internal SME and expect these updated connection params from
wpa_supplicant. Do not send this request for the drivers using
SME from wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If FT over-the-DS case is enforced through the "FT_DS <BSSID>" control
interface command, the PMF capability check during BSS selection is not
used and that could have allowed PMF to be disabled in the over-the-DS
case even if the local network profile mandated use of PMF. Check
against this explicitly to avoid unexpected cases if the APs within the
same mobility domain are not configured consistently.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
PMF capability check is done as part of BSS selection routines, but
those are not used when going through the enforced roaming operation
("ROAM <BSSID>" control interface command). While that mechanism is
mainly for testing purposes, extend it to do the same check for PMF to
prevent cases where forced roaming could end up disabling PMF against
the local profile requirement.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Commit e820cf952f ("MFP: Add MFPR flag into station RSN IE if 802.11w
is mandatory") added indication of MFPR flag in non-FT cases, but forgot
to do so for the FT protocol cases where a different function is used to
build the RSNE. Do the same change now for that FT specific case to get
consistent behavior on indicating PMF configuration state with MFPR.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
An OCE AP with WPA2 enabled shall require PMF negotiation when
associating with an OCE STA. An OCE STA-CFON may negotiate PMF with a
STA when it is operating as an AP. Don't select an OCE AP for connection
if PMF is not enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When required_roaming_consortium is set in a credential, station
should match this against Roaming Consortium(s) for a BSS similar
to how it is matching for roaming_consortiums during Interworking
credentials availability check for roaming_consortium.
In the context of Hotspot 2.0 PPS MO, this means addressing matching
part in the same manner for HomeSP/HomeOIList/<X+>/HomeOI regardless of
how HomeSP/HomeOIList/<X+>/HomeOIRequired is set (i.e., the required
part is used as an independent check for the AP advertising the needed
information while the "credential can be used here and this is a home
network" part is shared).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE Std 802.11-2016 does not require this behavior from a SAE STA, but
it is not disallowed either, so it is useful to have an option to
identify the derived PMKSA in the immediately following Association
Request frames. This is disabled by default (i.e., no change to previous
behavior) and can be enabled with a global wpa_supplicant configuration
parameter sae_pmkid_in_assoc=1.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is not used only with FT, so make the comments less confusing and
include the function in all builds to make it available for
non-FT/non-FILS builds.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The wlan.mesh.config doesn't have to be the last element of beacon. Things
like VHT or HE oper/cap are usually follow the mesh configuration element.
The workaround must first get the position of a correct reference value in
wlan.mesh.config (ps_protocol) and then calculate the correct
wlan.mesh.config.cap offset based on that.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Fixes: 2cbaf0de22 ("tests: Work around tshark bug in wpas_mesh_max_peering")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
HE (802.11ax) is also supported on 2.4 GHz. And the 2.4 GHz band isn't
supposed to use VHT operations. Some codepaths in wpa_supplicant will
therefore not initialize the freq->bandwidth or the freq->center_freq1/2
members. As a result, the nl80211_put_freq_params() will directly return
an error (-1) or the kernel will return an error due to the invalid
channel definition.
Instead, the channel definitions should be created based on the actual
HT/VHT/none information on 2.4 GHz.
Fixes: ad9a1bfe78 ("nl80211: Share VHT channel configuration for HE")
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
The OpenSSL error codes used here were for certificates, not CRLs. Fix
that to refer to CRL being expired or not yet valid.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add vendor command QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT
and attribute qca_wlan_vendor_attr_avoid_frequency_ext to send structured
avoid frequency data.
This new command is alternative to existing command
QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY since existing command is
using stream of bytes instead of structured data using vendor attributes.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
As a part of P802.11ax amendment, 6 GHz band operation is added.
Since the 6 GHz channel numbers are overlapping with existing 2.4 GHz
and 5 GHz channel numbers, use frequency to identify unique channel
operation instead of channel number. Channel frequency is unique across
bands.
In the existing QCA vendor interface, wherever missing, add frequency
attributes to identify unique channel operation. In addition, add
comments to document some of the previously missed attributes/values.
Note: If both channel and frequency attributes are present in vendor
command/event and
(a) If both the driver and user-space application supports 6 GHz band
then channel related attributes are deprecated and use frequency
attributes.
(b) If either driver or user-space application or both doesn't
support 6 GHz band then use channel attributes.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Add QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL attribute in
enum qca_wlan_vendor_attr_sap_config to use with vendor command
QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG.
This new attribute is used to restart AP on given channel.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Add a QCA vendor sub command QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY
with attributes enum qca_wlan_vendor_attr_acs_config and
enum qca_acs_dfs_mode to configure ACS policy.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
This enhances the existing vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM
with the following configurations:
1. Set/get/clear roam control
2. Set/get the channels on which the roaming has to be triggered.
3. Set/get the roam scan period.
4. Configure the triggers for roaming.
5. Configure the candidate selection criteria.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
qca_wlan_vendor_attr_roam_subcmd is an enum associated with the
attribute QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD. It represents different
sub command values and these are not the attributes. Hence, rename the
enum to qca_wlan_vendor_roaming_subcmd. Accordingly, the members of this
enum are also renamed to suite the usage.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The conditions for the eapol_sm_notify_eap_success(FALSE) calls did not
cover the case where eapol_sm_notify_eap_success(TRUE) had been called
based on offloaded 4-way handshake and driver notification of
authorization in wpa_supplicant_event_port_authorized(). This could
result in eapSuccess and altSuccess state machine variables being left
TRUE when roaming to another BSS and that results in EAP failure if the
following roaming case does not get fully authorized through the driver
offload.
Fix this by clearing eapSuccess/altSuccess when processing a new
association (including roaming) event and also when disconnecting from
the network.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update the version number for the build and also add the ChangeLog
entries for both hostapd and wpa_supplicant to describe main changes
between v2.7 and v2.8.
Signed-off-by: Jouni Malinen <j@w1.fi>
