Add a new OCV-FAILURE control interface event to notify upper layers of
OCV validation issues. This commit adds this for SA Query processing in
AP mode.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make reporting of OCV validation failure reasons more flexible by
removing the fixed prefix from ocv_verify_tx_params() output in
ocv_errorstr so that the caller can use whatever prefix or encapsulation
that is most appropriate for each case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
To support the STA testbed role, the STA has to use specified channel
information in OCI element sent to the AP in EAPOL-Key msg 2/4, SA Query
Request, and SA Query Response frames. Add override parameters to use
the specified channel while populating OCI element in all these frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It was possible for the RSN state machine to maintain old PMKSA cache
selection (sm->cur_pmksa) when roaming to another BSS based on
driver-based roaming indication. This could result in mismatching state
and unexpected behavior, e.g., with not generating a Suite B PMKSA cache
entry.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that RSNE, MDE, and FTE have valid information in FT
Reassociation Response frames. In addition, decrypt GTK, IGTK, and BIGTK
from the frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is expected for the STA entry on the target AP to move directly from
State 1 to State 3 when performing FT over-the-DS (i.e., FT Action
Request/Response frame exchange through the old AP followed by
Reassociation Request/Response frame exchange with the target AP).
Signed-off-by: Jouni Malinen <j@w1.fi>
Define QCA vendor attributes for SET(GET)_WIFI_CONFIGURATION to
dynamically configure capabilities for TX A-MSDU and RX A-MSDU.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Add a QCA vendor subcommand QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC
to add and delete TSPEC in STA mode.
The attributes defined in enum qca_wlan_vendor_attr_config_tspec
are used to encapsulate required information.
Signed-off-by: Min Liu <minliu@codeaurora.org>
Add new QCA vendor attributes to configure misbehavior for PMF
protection for Management frames and to inject Disassociation frames.
These attributes are used for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an attribute that can be used with
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION vendor command to
configure different PHY modes to the driver/firmware.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wpa_supplicant registered to process the Radio Measurement Request
frames unconditionally. This would prevent other location based
applications from handling these frames. Enable such a use case by
allowing wpa_supplicant to be configured not to register to process
these frames. This can now be done by adding "no_rrm=1" to the
driver_param configuration parameter.
In addition, wpa_driver_nl80211_init() does not have the provision to
take driver_params. Hence, resubscribe again with cfg80211 when this
driver parameter "no_rrm=1" is set after the initial setup steps.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process HE 6 GHz band capabilities in (Re)Association Request frames and
pass the information to the driver.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Construct HE 6 GHz Band Capabilities element (IEEE 802.11ax/D6.0,
9.4.2.261) from HT and VHT capabilities and add it to Beacon, Probe
Response, and (Re)Association Response frames when operating on the 6
GHz band.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
The VHT Operation Information subfield is conditonally present, so do
not hardcoded it in struct ieee80211_he_operation. These members of the
struct are not currently used, so these can be removed without impact to
functionality.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Defines IEEE P802.11ax/D6.0, 9.4.2.261 HE 6 GHz Band Capabilities
element and 6 GHz Operation Information field of HE Operation element
(IEEE P802.11ax/D6.0, Figure 9-787k).
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Some distros (e.g., Debian and Arch) already build wpa_supplicant with
support for TDLS, and Fedora is about to enable this feature as well.
Set CONFIG_TDLS=y in wpa_supplicant default build configuration.
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
If the current country code cannot be fetched, do not try to report the
current value in the log since that will result in TypeError exception.
Signed-off-by: Jouni Malinen <j@w1.fi>
Couple of VHT test cases missed explicit setting of hapd to None before
trying to start hostapd. Add those to avoid unexpected exceptions in
case hostapd start fails.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a decorator that clears ignore_old_scan_res parameter value instead
of doing this with try/finally in large number of test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a decorator that disables IPv6 and requires running
under a VM, rather than open-coding that many times.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The freqlist parameter uses comma, not space, separated values. Add
another test case for checking freqlist values that do not use the
preferred channel numbers to make sure the frequency list is actually
used as a constraint for selecting the channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a test for delayed group rekey retransmission that checks that
the IGTK is protected against it by not resetting the IPN replay
counter when reinstalling such a key.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While adding support for IGTK and BIGTK here, I tested this without
protections (i.e., with protections removed from both wpa_supplicant and
the driver), and while I got some bad resets on the debugfs values, it
should have failed with "unexpected connectivity".
Fix this to be correct - we need to reset the GTK PN, not the PTK PN in
this test.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use a shared wpa_alg_bip() function for this and fix the case in
nl_add_key() to cover all BIP algorithms. That fix does not change any
behavior since the function is not currently used with any BIP
algorithm, but it is better to avoid surprises should it ever be needed
with IGTK.
Signed-off-by: Jouni Malinen <j@w1.fi>
IGTK is the key that is used a BIP cipher. WPA_ALG_IGTK was the
historical name used for this enum value when only the AES-128-CMAC
based BIP algorithm was supported. Rename this to match the style used
with the other BIP options.
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace the gtk boolean by a keytype value indicating
GTK or PTK, to be able to extend to other types later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was apparently possible to hit the 20000 octet limit in some cases,
so increase the limit to avoid process termination due to insufficient
room for preparing a response to Introspect calls.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is not really appropriate for any kind of cross compilations and is
not really needed in general since system specific values can be set in
.config.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous implementation used mp_rand_prime() to generate a random
value in range 0..m. That is insanely slow way of generating a random
value since mp_rand_prime() is for generating a random _prime_ which is
not what is needed here. Replace that implementation with generationg of
a random value in the requested range without doing any kind of prime
number checks or loops to reject values that are not primes.
This speeds up SAE and EAP-pwd routines by couple of orders of
magnitude..
Signed-off-by: Jouni Malinen <j@w1.fi>
When run after other tests, It was likely that the target
bss was already present in scan_fail, so the
scan_for_bss() wouldn't trip the allocation failure in
wpa_bss_add(). Flush the scan results before the scan to
ensure wpa_bss_add() is called and consistently pass
scan_fail.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
If sigma_dut is not installed, start_sigma_dut() will
throw an exception. Call start_sigma_dut() inside the
try/except to correctly reset the regulatory domain.
This fixes several seemingly random failures due to
regulatory domain not being reset.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Commit dd74ddd0df ("nl80211: Handle AKM suite selectors for AP
configuration") added warning log message "nl80211: Not enough room for
all AKM suites (num_suites=X > NL80211_MAX_NR_AKM_SUITES)" which in some
cases fills logs every 3 seconds, so fix this by increasing the log
message level to debug.
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Ref: https://patchwork.ozlabs.org/project/openwrt/patch/20200504130757.12736-1-ynezz@true.cz/#2429246
Fixes: dd74ddd0df ("nl80211: Handle AKM suite selectors for AP configuration")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
