Commit graph

504 commits

Author SHA1 Message Date
Jouni Malinen
e65a87b399 Debug print scan results matching the currently selected network
This provides more details on BSS selection process in the debug log.
Previously, the BSSs that were not either the current or the selected
one were not necessarily printed at all. Now all BSSs that match the
currently selected network are listed with their frequency and signal
strength details.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-11-13 18:22:38 +02:00
Jouni Malinen
8d1e693186 Use estimated throughput to avoid signal based roaming decision
Previously, the estimated throughput was used to enable roaming to a
better AP. However, this information was not used when considering a
roam to an AP that has better signal strength, but smaller estimated
throughput. This could result in allowing roaming from 5 GHz band to 2.4
GHz band in cases where 2.4 GHz band has significantly higher signal
strength, but still a lower throughput estimate.

Make this less likely to happen by increasing/reducing the minimum
required signal strength difference based on the estimated throughputs
of the current and selected AP. In addition, add more details about the
selection process to the debug log to make it easier to determine whaty
happened and why.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-11-13 17:52:32 +02:00
Jouni Malinen
81a10a9442 Do not try to start/join RSN IBSS without CONFIG_IBSS_RSN=y
Previously, a build without IBSS RSN support tried to start/join an IBSS
even if the profile was configured with RSN parameters. This does not
work and resulted in quite confusing debug log. Make this clearer by
explicitly checking for this case and reject the connection attempt with
a clearer debug log entry instead of trying something that is known to
fail.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-28 19:33:20 +03:00
Jouni Malinen
706df4291b FILS: Association Response processing (STA)
Decrypt the AES-SIV protected elements and verify Key-Auth. Parse and
configure keys to the driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-26 00:20:04 +03:00
Avraham Stern
e3e2fe3a42 Always propagate scan results to all interfaces
Scan results were not propagated to all interfaces if scan results
started a new operation, in order to prevent concurrent operations. But
this can cause other interfaces to trigger a new scan when scan results
are already available. Instead, always notify other interfaces of the
scan results, but note that new operations are not allowed.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2016-10-15 19:13:30 +03:00
Avraham Stern
14f34a7303 Continue scanning if sched_scan stops unexpectedly
When scheduled scan stops without the interface request (for example,
driver stopped it unexpectedly), start a regular scan to continue
scanning for networks and avoid being left with no scan at all.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-10-02 19:38:57 +03:00
David Spinadel
1ac388633a Remove disconnected APs from BSS table if likely out-of-range
In some cases, after a sudden AP disappearing and reconnection to
another AP in the same ESS, if another scan occurs, wpa_supplicant might
try to roam to the old AP (if it was better ranked than the new one)
because it is still saved in BSS list and the blacklist entry was
cleared in previous reconnect. This attempt is going to fail if the AP
is not present anymore and it'll cause long disconnections.

Remove an AP that is probably out of range from the BSS list to avoid
such disconnections. In particular mac80211-based drivers use the
WLAN_REASON_DISASSOC_DUE_TO_INACTIVITY reason code in locally generated
disconnection events for cases where the AP does not reply anymore.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-10-01 11:14:02 +03:00
Arik Nemtsov
ebf59eb549 Restart PNO/sched_scan on channel list update
As the scan channels might need to change when the channel list has been
updated by the kernel. Use the simulated sched_scan timeout
(wpas_scan_restart_sched_scan()) to handle a possible race where an
ongoing sched_scan has stopped asynchronously while trying to restart a
new sched_scan.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2016-09-30 22:45:03 +03:00
vamsi krishna
6ad37d73ca MBO: Add support to ignore association disallowed set by AP
Add a testing mechanism to allow association disallowed set by AP to be
ignored. This can be used to verify AP behavior for disallowing a
specific association.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-09-25 17:31:26 +03:00
Mikael Kanstrup
02adead53e Add ignore_auth_resp control interface debug parameter
Implement "SET ignore_auth_resp <0/1>" command to simulate auth/assoc
response loss and EAPOL RX packet loss by ignoring corresponding
incoming events.

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
2016-09-23 17:36:55 +03:00
Moshe Benji
14220fe64c Flush the BSS (scan) entries when an interface becomes disabled
When an interface becomes disabled (e.g., when RF-kill becomes blocked)
we should clear the stored scan results to avoid maintaining stale
information.

Fix this by flushing the BSS entries when an interface becomes
disabled.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
2016-09-22 23:31:19 +03:00
Jouni Malinen
6c33ca9f95 Add group_rekey parameter for IBSS
The new network profile parameter group_rekey can now be used to specify
the group rekeying internal in seconds for IBSS.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-08-13 16:29:01 +03:00
Jouni Malinen
e07adb7faa Fix EAP state machine reset with offloaded roaming and authorization
If the driver indicates a roamed event with already completed
authorization, altAccept = TRUE could have resulted in the EAP state
machine ending up in the FAILURE state from the INITIALIZE state. This
is not correct behavior and similar cases were already addressed for FT
and WPA-PSK. Fix the offloaded roamed+authorized (EAP/PMKSA caching)
case by doing similar changes to EAPOL/EAP state variable updates during
association event handling.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-08-11 16:05:45 +03:00
Masashi Honma
fac72f93dd mesh: Stop joining to different frequency network
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2016-07-23 21:57:15 +03:00
Masashi Honma
7035162311 mesh: Join an existing MBSS instead of creating a new one
If scan results show a matching existing MBSS, join it instead of
creating a new MBSS.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2016-07-23 21:57:11 +03:00
Peng Xu
a6f5b1937a P2P: Allow P2P listen being offloaded to the driver/firmware
This allows P2P Listen to be offloaded to device to enhance power
saving.

To start P2P listen offload, from wpa_cli interface, issue the command:
	p2p_lo_start <freq> <period> <interval> <count>

To stop P2P listen offload, issue the command:
	p2p_lo_stop

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-07-03 22:36:58 +03:00
Jouni Malinen
37fd0be2d3 Add CTRL-EVENT-CHANNEL-SWITCH event to indicate channel changes
This provides information of the channel switch to wpa_supplicant
control interface monitors.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-06-27 21:10:35 +03:00
Jouni Malinen
9a5160f5fb Report connection timeouts in CTRL-EVENT-ASSOC-REJECT
Add a new "timeout" argument to the event message if the nl80211 message
indicates that the connection failure is not due to an explicit AP
rejection message. This makes it easier for external programs to figure
out why the connection failed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-05-31 00:11:42 +03:00
Lior David
a26c9c2e71 Fix sending non-Public Action frames over P2P Device interface
The P2P Device interface can only send Public Action frames. Non-Public
Action frames must be sent over a group interface. The previous
implementation sometimes tried to send non-Public Action frames such as
GO Discoverability over the P2P Device interface, however, the source
address of the frame was set to the group interface address so the code
in offchannel.c knew to select the correct interface for the TX.

The check breaks when the P2P Device and group interfaces have the same
MAC address. In this case the frame will be sent over the P2P Device
interface and the send will fail.

Fix this problem in two places:
1. In offchannel, route non-Public Action frames to the GO
   interface when the above conditions are met.
2. When a TX_STATUS event arrives on such routed frame, it will
   arrive on the GO interface but it must be handled by the P2P Device
   interface since it has the relevant state logic.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-05-21 00:17:45 +03:00
Ilan Peer
3b11ad34eb Send CTRL-EVENT-REGDOM-CHANGE event on the parent interface
The NL80211_CMD_WIPHY_REG_CHANGE can be handled by any of the
interfaces that are currently controlled by the wpa_supplicant.
However, some applications expect the REGDOM_CHANGE event to be
sent on the control interface of the initially added interface
(and do not expect the event on any of child interfaces).

To resolve this, when processing NL80211_CMD_WIPHY_REG_CHANGE,
find the highest parent in the chain, and use its control interface
to emit the CTRL-EVENT-REGDOM-CHANGE event.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2016-05-14 17:19:02 +03:00
Sunil Dutt
03626e9157 Skip connection attempt for non-RSN networks if PMF is set to required
Since ieee80211w=2 is an explicit configuration to wpa_supplicant, the
connection attempt for such non-PMF (non-RSN) capable networks should be
skipped.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-05-05 21:09:08 +03:00
David Spinadel
4a742011ab wpa_supplicant: Handle LCI request
Handle radio measurement request that contains LCI request. Send
measurement report based on a configurable LCI report element. The LCI
report element is configured over the control interface with

SET lci <hexdump of the element>

and cleared with

SET lci ""

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-04-17 12:29:12 +03:00
Matti Gottlieb
ece4ac5f4e HS 2.0: Add support for configuring frame filters
When a station starts an association to a Hotspot 2.0 network, request
the driver to do the following, based on the BSS capabilities:

1. Enable gratuitous ARP filtering
2. Enable unsolicited Neighbor Advertisement filtering
3. Enable unicast IP packet encrypted with GTK filtering if
   DGAF disabled bit is zero

Clear the filter configuration when the station interface is
disassociated.

Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
2016-04-08 15:21:18 +03:00
Lior David
90f14962ec wpa_supplicant: "don't care" value for pbss in ssid structure
Add a new value 2 to the pbss parameter of wpa_ssid structure, which
means "don't care". This value is used in infrastructure mode to request
connection to either AP or PCP, whichever is available in the scan
results. The value is also used in regular WPS (not P2P group formation)
to make WPS work with devices running as either AP or PCP.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-04-08 12:56:34 +03:00
Hu Wang
3560b32ca3 Fix race condition with PNO stop followed immediately by PNO start
Commit dd271857a5 ('Skip normal scan when
PNO is already in progress') fixed issues with normal scans getting
rejected by the driver when PNO scan is already running. The part about
skipping such a scan request is fine, but the part about clearing
wpa_s->pno back to 0 in EVENT_SCHED_SCAN_STOPPED handler is problematic.

If PNO is stopped ("SET pno 0") and then restarted ("SET pno 1")
immediately, it is possible for the EVENT_SCHED_SCAN_STOPPED event from
the stopping part to be received only after the new PNO instance has
been started. This would have resulted in clearing wpa_s->pno and the
driver and wpa_supplicant getting out of sync. This would then prevent
PNO from being stopped with "SET pno 0" (that fails if wpa_s->pno == 0).

Fix this race condition by reverting the wpa_s->pno = 0 addition from
the EVENT_SCHED_SCAN_STOPPED handler.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-04-06 11:14:34 +03:00
Jouni Malinen
c01120a05f wpa_supplicant: Do not use struct ieee80211_mgmt::u.probe_req
This struct in the union is empty, but the design of using a zero-length
u8 array here is not fully compatible with C++ and can result in
undesired compiler warnings. Since there are no non-IE fields in the
Probe Request frames, get the location of the variable length IEs simply
by using the pointer to the frame header and the known header length.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-04-02 16:55:02 +03:00
Jouni Malinen
954e10e483 Make it a bit easier to roam from 2.4 GHz to 5 GHz within ESS
The initial connection to an ESS was already explicitly increasing the
likelihood of picking a 5 GHz BSS. While the throughput estimation is
likely to do same for the roaming decision, it might be possible that
that does not cover all cases. Add couple of dB extra preference for 5
GHz in case the roaming decision falls back to comparing signal levels.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-03-25 12:12:48 +02:00
Roy Marples
2e997eece5 Add interface matching support with -M, guarded by CONFIG_MATCH_IFACE
The new wpa_supplicant command line argument -M can be used to describe
matching rules with a wildcard interface name (e.g., "wlan*").

This is very useful for systems without udev (Linux) or devd (FreeBSD).

Signed-off-by: Roy Marples <roy@marples.name>
2016-03-22 17:41:37 +02:00
Roy Marples
45e3fc72c6 Find correct driver for interface additions/removals
Interface additions/removals are not guaranteed to be for the driver
listening to the kernel events. As such, send the events to
wpa_supplicant_event_global() which can then pick the correct interface
registered with wpa_supplicant to send the event to.

Signed-off-by: Roy Marples <roy@marples.name>
2016-03-22 17:41:37 +02:00
Daisuke Niwa
192964ddc3 Handle OSEN IE in Assoc Request info if req_ies exists
The 4-way handshake fails with the error "WPA: No wpa_ie set - cannot
generate msg 2/4" while connecting to OSEN network with drivers that
indicate used Association Request frame elements because OSEN IE is not
handled in wpa_supplicant_event_associnfo() if data->assoc_info.req_ies
is not NULL.

Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
2016-03-20 11:17:39 +02:00
Naveen Singh
c7fb678f31 D-Bus: Add association response status code property for failure cases
(Re)Association Response frame with status code other than 0 is now
notified over DBUS as a part of PropertiesChanged signal. This can be
used by application in case AP is denying association with status code
17 (band steering) so that it does not interfere in the BSSID selection
logic of wpa_supplicant.

Signed-off-by: Naveen Singh <nasingh@google.com>
2016-03-06 20:44:51 +02:00
Ilan Peer
1446afc865 wpa_supplicant: Handle EVENT_SCAN_RESULTS when an interface is disabled
An interface can be disabled while it has an ongoing scan request.
In such a case, when the scan results notification is received,
it was being ignored (as the interface is already disabled) so the
scan state was not cleared. This can cause undetermined behavior
for the next scan request.

To handle this, clear the scan state when EVENT_SCAN_RESULTS is
received and the interface is disabled.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2016-03-03 17:10:26 +02:00
Jouni Malinen
bef5e9a862 Fix scan rescheduling from wpas_stop_pno to check postponed case
Commit 02e122a995 ('Reschedule scan from
wpas_stop_pno if it was postponed') uses wpa_s->scanning as the only
condition for automatically starting a postponed scan request from
EVENT_SCHED_SCAN_STOPPED event handler. However, wpa_s->scanning may be
set for sched_scan and as such, this can result in unexpected extra
scans without there having been any real postponed request.

Make this more accurate by verifying that there really is a pending
request for a scan before speeding up its start.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-03-03 11:04:38 +02:00
Jouni Malinen
940491ce08 MBO: Mandate use of PMF for WPA2+MBO association (STA)
If WPA2 is used, MBO AP must enable PMF. Refuse to select a BSS that has
MBO and WPA2 enabled without PMF.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-02-22 19:53:05 +02:00
Avraham Stern
84d1c0fd5a WNM: Add candidate list to BSS transition response
Add the transition candidate list to BSS Transition Management Response
frame. The candidates preference is set using the regular wpa_supplicant
BSS selection logic. If the BSS transition request is rejected and
updated scan results are not available, the list is not added.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
Avraham Stern
dd5999084e MBO: Parse MBO IE in BSS Transition Management Request frames
Add parsing of MBO IE in BSS Transition Management Request frames. If
the MBO IE includes the association retry delay attribute, do not try to
reconnect to the current BSS until the delay time is over.

If the MBO IE includes the cellular data connection preference attribute
or the transition rejection reason attribute, send a message to upper
layers with the data.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2016-02-22 19:53:04 +02:00
David Spinadel
cb06cf3456 MBO: Prevent association to APs that explicitly disallow this
Prevent association to MBO APs that have association disallowed
attribute in MBO IE in Beacon or Probe Response frames.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-02-22 19:53:04 +02:00
Lior David
b907491281 wpa_supplicant: Basic support for PBSS/PCP
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.

Add a new "pbss" argument to network block. The argument is used
in the following scenarios:
1. When network has mode=2 (AP), when pbss flag is set will start
as a PCP instead of an AP.
2. When network has mode=0 (station), when pbss flag is set will
connect to PCP instead of AP.

The function wpa_scan_res_match() was modified to match BSS according to
the pbss flag in the network block (wpa_ssid structure). When pbss flag
is set it will match only PCPs, and when it is clear it will match only
APs.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-02-08 22:23:56 +02:00
Tomasz Bursztyka
d99097177a wpa_supplicant: Enable Automatic Channel Selection support for AP mode
Since hostapd supports ACS now, let's enable its support in
wpa_supplicant as well when starting AP mode.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
[u.oelmann@pengutronix.de: adjusted added text in defconfig]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
2015-12-24 22:24:05 +02:00
Tomasz Bursztyka
96bc508684 Handle survey event properly in wpa_supplicant
Let's reuse hostapd code for such handling. This will be useful to get
ACS support into wpa_supplicant where this one needs to handle the
survey event so it fills in the result ACS subsystem will require.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
[u.oelmann@pengutronix.de: rebased series from hostap_2_1~944 to master]
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
2015-12-24 21:35:54 +02:00
Ayala Beker
0e6a2cf282 Disconnect before trying to switch to a different network
Previously, when wpa_supplicant received bgscan results with a preferred
network, it connected to that network without disconnecting from the
previous one. This might result in an inconsistent state of upper
layers.

Fix this by disconnecting from the current AP before connecting to the
new one when the network profile changes and there is an existing
connection.

Signed-off-by: Ayala Beker <ayala.beker@intel.com>
2015-12-18 00:24:52 +02:00
Arik Nemtsov
706e11a485 Avoid network selection from scan during connection
If scan results arrive during the connection process, the network
selection function was called, interrupting the current connection.
While a regular scan is mutually exclusive with connection establishment
via the nature of radio work, there's no such protection for scheduled
scan. Prevent network selection while a connection is in progress.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2015-12-18 00:24:52 +02:00
Jouni Malinen
58059e6c0c FST: Print debug entry on MB IE update based on EVENT_AUTH
This is more consistent with all the other callers of
wpas_fst_update_mbie().

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-12-06 12:53:24 +02:00
Dedy Lansky
ea7081185e FST: Improve parsing of Multiband IEs
Previously, MB IEs were parsed only from association event. Try to get
MB IEs from other management frames like Probe Response frames. The MB
IEs from the association event may not be up-to-date and in some cases
may actually be missing and updating the information based on other
frames can improve robustness of FST exchanges.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-25 17:33:31 +02:00
Jouni Malinen
eb926f1257 Comment out wpas_reenabled_network_time with CONFIG_NO_SCAN_PROCESSING
This removes a compiler warning about unused function.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-23 23:33:55 +02:00
Ravi Joshi
f32227ed9e Add QCA vendor attribute and event to indicate subnet change status
This allows offloaded roaming to inform user space of the change in IP
subnet post roaming. The device may have roamed to a network which is in
a different subnet which will result in IP connectivity loss. Indicating
the change in subnet enables the user space to refresh the IP address or
to perform IP subnet validation if unknown status is indicated.

The driver indication is reported with a new event from wpa_supplicant
in the following format:
CTRL-EVENT-SUBNET-STATUS-UPDATE status=<0/1/2>
where
0 = unknown
1 = IP subnet unchanged (can continue to use the old IP address)
2 = IP subnet changed (need to get a new IP address)

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-20 11:03:06 +02:00
Sunil Dutt
5e238cc682 WPS: Reconnect for a failed data connection when STA_AUTOCONNECT is 0
If "STA_AUTOCONNECT 0" has been used to disable automatic connection on
disconnection event and the driver indicates a failure for the data
connection after successful WPS handshake, it is possible to hit a case
where wpa_s->disconnected is set to 1 and further attempts to connect
shall stop.

While "STA_AUTOCONNECT 0" is used to disable automatic reconnection
attempts in general, this specific WPS case can benefit from trying
again even with that configuration for a short period of time. Extend
the wpa_supplicant re-enable-networks-after-WPS 10 second timeout to
apply for ignoring disabled STA_AUTOCONNECT immediately after a WPS
provisioning step.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-17 19:50:34 +02:00
Jouni Malinen
03ed0a5239 WNM: Ignore WNM-Sleep Mode Response if WNM-Sleep Mode has not been used
The AP is not expected to send out a WNM-Sleep Mode Response frame
without the STA trying to use WNM-Sleep Mode. Drop such unexpected
responses to reduce unnecessary processing of the frame.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-10 18:40:54 +02:00
Jouni Malinen
fa46426725 RSN: Do not try to connect if PMF disabled and AP requires it
Instead of trying to associate in configuration that is known to result
in the AP rejecting the association, reject the BSS candidate based on
the MFPR=1 RSN capability when STA configuration has PMF disabled.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-10-25 19:37:17 +02:00
Ilan Peer
61f121d925 Handle channel switch notification for other interface types
Channel switch notification was handled only for AP/GO interfaces. As
the notification can be sent on other interface types as well, extend
the handling to handle other interface types.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-10-03 21:01:49 +03:00
Andrei Otcheretianski
3bafb0d842 P2P: Trigger channel selection correctly during CSA
Do not consider moving GOs to a new channel if one of them is in the
middle of CSA. In addition, call wpas_p2p_update_channel_list() after
EVENT_CH_SWITCH is handled.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2015-10-03 20:22:09 +03:00
Kanchanapally, Vidyullatha
adcd7c4b0b nl80211: Support vendor scan together with normal scan
Allow wpa_supplicant to use vendor scan (if supported by the driver)
together with the normal nl80211 scan and handling external scan events.
Since this results in possibility of concurrent scan operations, some of
the operations related to scan results need to check more carefully when
an event is relevant for a specific interface.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-10-01 01:41:46 +03:00
Saurav Babu
0a7b2a02eb D-Bus: Add Signal to notify WPS PBC Overlap event
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2015-09-27 12:52:34 +03:00
Sunil Dutt
ce7d0eb184 Update AP WPA/RSN IE on all associations if driver can select BSS
It is possible for driver-based BSS selection to end up reassociating
back to the current AP. If wpa_supplicant preferred another BSS, it
would have updated the internal knowledge of the AP's WPA/RSN IE when
requesting a new connection. In the special case of existing association
and new association being with the same BSS that is different from the
wpa_supplicant preference, association event processing skipped the
WPA/RSN IE update. This could result in the following 4-way handshake
getting rejected due to incorrectly detected mismatch with AP's RSN/WPA
IE between Beacon/Probe Response frame and EAPOL-Key msg 3/4.

Fix this by updating the AP WPA/RSN IE on all association events when
driver-based BSS selection is used regardless of whether the BSSID
changes. This could also cover a theoretical case of the AP changing its
RSN/WPA IE at the very moment we try to reassociate back to the same
BSS.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-09-17 17:40:40 +07:00
Jouni Malinen
dcc8bc82e0 Add BSS operating frequency to more debug messages
This makes it easier to analyze debug logs when figuring out channel
related issues.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-09-05 20:40:44 +03:00
Jouni Malinen
dfaf11d648 P2P: Require fresh scan results for persistent group re-invocation
The P2P group is not yet operating when going through invitation
exchange for re-invocation. Previously, an old cached scan result could
be used to skip the scan immediately after the invitation exchange.
While this may result in the fastest possible connection, it does have
some issues with cases where the GO takes some time to start up. It
would also be at least theoretically possible for some of the BSS
parameters to be different, so having a fresh scan result from the new
GO instance may be desired in any case.

Add a mechanism to skip scan results that have been last updated before
a specific point in time and as the first user for this mechanism,
require chan results to be more recent than the invitation message
exchange for the P2P Client role in persistent group re-invocation case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-22 00:22:12 +03:00
Mahesh A Saptasagar
0d0f7ecbb1 Do not stop ongoing PNO sched_scan on association/disconnection
PNO was stopped by the wpa_supplicant during the connection attempts or
while handling disassociation indication. External entities, mainly, the
Android Wi-Fi framework, does not expects PNO to be stopped by other
modules. Hence, do not stop the sched_scan in these scenarios if it is
triggered externally for PNO.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-13 21:10:16 +03:00
Ilan Peer
3a8f008a24 P2P: Do not perform P2P GO CS in some cases
A P2P GO channel switch should not be triggered in all cases that
require channel list update. Specifically, a P2P GO CS should not
be triggered in case that the P2P GO state changed or in case that
that the P2P GO has just completed a CS.

To fix this, add reason code to wpas_p2p_channel_list_update() and
trigger CS flow only for the relevant cases.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-08-04 18:34:47 +03:00
Arik Nemtsov
0f4bccdbbe Refactor channel list update event in wpa_supplicant
Update hardware features for all interfaces inside the loop, don't treat
the calling wpa_s instance specially. Perform the P2P channel list
updates after the hardware features are updated. This will prevent P2P
from relying on stale information.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2015-08-04 16:04:52 +03:00
Ilan Peer
a7160f7ede P2P: Remove GO handling in avoid frequency event
Remove the code that considers removing GOs from their current
channel due to frequency interference, as this is already handled
as part of the P2P channels update.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-08-04 00:32:36 +03:00
Jouni Malinen
9f59fe8dc8 P2P: Do not clear wpa_s->go_dev_addr before group removal
This variable is needed to figure out whether a wpa_supplicant interface
is for a P2P group that is (or was) connected to a specific GO. The
previous implementation was able to find such a case only when there was
an association with the GO. However, this may be needed even if there is
a temporary disconnection from the GO. Keep the GO device address
information over such temporary disconnections and only remove it on
group termination. This fixes an issue with D-Bus Peer PropertiesChanged
signals for the Groups property in case a P2P group gets removed due to
group idle timeout instead of explicit group termination command (local
request) or GO notification.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-08-02 21:37:09 +03:00
Anton Nayshtut
9fbfd1b0d4 FST: Send FST Action frame for processing (wpa_supplicant)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:15 +03:00
Anton Nayshtut
b36a3a65aa FST: Integration into wpa_supplicant
This commit integrates the FST into the wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:15 +03:00
Dmitry Shmidt
4f39908b60 Send CTRL-EVENT-NETWORK-NOT-FOUND if no suitable network was found
This provides more information to upper layer programs on what happens
with connection attempts in cases where the enabled networks are not
found in scan results.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2015-06-27 11:08:08 +03:00
Jouni Malinen
c1a14ef42f Do not check unsigned size is less than zero
The variables here are unsigned and as such, cannot have a negative
value. Use == 0 instead of <= 0 to make this cleaner.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-06-23 21:16:15 +03:00
Ilan Peer
f43c1ae798 P2P: Handle P2P Device dedicated interface parent removal
In case of a network interface removal, check if the interface
was also the parent interface of the P2P Device dedicated interface.
If this is the case, then stop the P2P Device functionality, and
remove the P2P Device dedicated interface.

In case that the interface is added again and P2P Device
functionality can be enabled again, add a new P2P Device dedicated
interface and allow further P2P Device functionality.

In case that the P2P Device dedicated interface is re-created, the
original P2P Device configuration file is needed, so store it in
the global params (instead in the wpa_interface configuration).

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-06-19 16:22:26 +03:00
Max Stepanov
734ddf6125 P2P: Add rx_freq parameter to Probe Request frame handler
In some cases, Probe Request frames can be received by a peer not only
on a listen channel. In this case an additional rx_freq parameter
explitly contains a Probe Request frame RX frequency. In case rx_freq is
set to 0, a Probe Request frame RX channel is assumed to be our own
listen channel (p2p->cfg->channel).

Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-06-14 23:16:55 +03:00
Avichal Agarwal
1a2f7ca1b8 D-Bus: Add WPS pbc-overlap Event
This sends an Event D-Bus signal with name "pbc-overlap" for
WPS-EVENT-OVERLAP.

Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
2015-06-10 20:51:30 +03:00
Jouni Malinen
eaa8eefed1 Replace MAX_SSID_LEN with SSID_MAX_LEN
This makes source code more consistent. The use within Android driver
interface is left as-is to avoid changes in the old PNO interface
definition.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-22 11:44:18 +03:00
Dmitry Shmidt
02e122a995 Reschedule scan from wpas_stop_pno if it was postponed
This reschedules the postponed scan request (if such a request is
pending) from EVENT_SCHED_SCAN_STOPPED event handler to speed up
scanning after PNO/sched_scan stop has been requested.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2015-04-01 18:21:36 +03:00
Lauri Hintsala
ce18c10773 Add support for CONFIG_NO_ROAMING to Makefile
Commit e9af53ad39 introduced new
CONFIG_NO_ROAMING configuration parameter but unfortunately it was added
only to Android.mk. Enabling this parameter didn't have any effect when
Makefile was used to build wpa_supplicant. This commit fixes that problem
and cleans "unused variable" compiler warning.

Signed-off-by: Lauri Hintsala <lauri.hintsala@silabs.com>
2015-03-29 20:37:39 +03:00
Jouni Malinen
a52410c29f Allow PSK/passphrase to be set only when needed
The new network profile parameter mem_only_psk=1 can be used to specify
that the PSK/passphrase for that network is requested over the control
interface (ctrl_iface or D-Bus) similarly to the EAP network parameter
requests. The PSK/passphrase can then be configured temporarily in a way
that prevents it from getting stored to the configuration file.

For example:

Event:
CTRL-REQ-PSK_PASSPHRASE-0:PSK or passphrase needed for SSID test-wpa2-psk

Response:
CTRL-RSP-PSK_PASSPHRASE-0:"qwertyuiop"

Note: The response value uses the same encoding as the psk network
profile parameter, i.e., passphrase is within double quotation marks.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-28 11:05:13 +02:00
Krishna Vamsi
c41d0840a1 nl80211: Allow driver-based roam to change ESS
This extends NL80211_CMD_ROAM event processing to allow the driver to
roam to another ESS (different SSID) when using offloaded BSS selection.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-24 21:13:28 +02:00
Avraham Stern
9bd566a33a Delay AP selection if all networks are temporarily disabled
If all networks are temporarily disabled, delay AP selection until at
least one network is enabled. Running AP selection when all networks are
disabled is useless as wpa_supplicant will not try to connect. In
addition, it will result in needless scan iterations that may delay the
connection when it is needed.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-03-22 20:53:58 +02:00
Victor Goldenshtein
6ceea4c3cb Restart sched_scan on channel list change
The channel list can be changed as a result of arriving beacon hints
during normal scan or as a result of local Reg-Domain change. Some
passive channels can become active and needs to be reconfigured
accordingly for the scheduled scan.

This fixes the connection to hidden SSIDs on 5 GHz band during default
Reg-Domain 00 (world roaming).

Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2015-03-20 15:56:59 +02:00
Jouni Malinen
1d246a1db9 Make rate-not-supported debug print more useful
It looks like "hardware does not support required rate 1.0 Mbps" has
started showing up in some hwsim test cases as a reason for failure.
This should not really occur with mac80211_hwsim, so add more details to
the debug print to make it easier to figure out what exactly happened.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-07 15:35:40 +02:00
Sunil Dutt
c10ca2a66f TDLS: Allow driver to request TDLS Discovery Request initiation
This extends the TDLS operation request mechanism to allow TDLS
Discovery Request to be initiated by the driver similarly to the
existing Setup and Teardown requests.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-06 21:08:54 +02:00
Ahmad Kholaif
bd0f68c473 DFS: wpa_supplicant event processing
Add radar event processing logic for AP/P2P GO. The DFS processing
functions from hostapd are now used for these wpa_supplicant cases as
well for both offloaded and non-offloaded DFS.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-05 17:24:16 +02:00
Jouni Malinen
c28059091a Do not add blacklist entries based on normal disconnect request cases
There are number of cases where wpa_supplicant requests the current
connection to be disconnected before starting a new operation. Such
cases do not really indicate that there was an error in connecting or a
disconnection initiated by the AP, so do not add a temporary blacklist
entry in such sequences.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 15:54:24 +02:00
Jouni Malinen
44b9ea5bb2 P2P: Do not allow scan or normal association on cfg80211 P2P Device
The dedicated P2P management instance (wpas->p2p_mgmt == 1) using
cfg80211 P2P Device cannot be used for non-P2P uses or connection (there
is no netdev). Reject or ignore such operations to avoid unexpected
operations if enabled network blocks are configured in the
wpa_supplicant instance used to control this interface.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 11:23:09 +02:00
Jouni Malinen
0d2030ee20 Use estimated throughput to improve roaming selection
Previously, within-ESS roaming was skipped if the selected BSS did not
have a higher signal strength than the current BSS regardless of AP
capabilities. This could result in not moving to a BSS that would
provide higher throughput, e.g., due to larger channel bandwidth or
higher rates (HT/VHT MCS).

Use estimated throughput information from scan result processing to
allow within-ESS roaming if the selected BSS is likely to provide better
throughput even if the current BSS has larger RSSI.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-22 11:45:45 +02:00
Matthieu Mauger
71d77adb6d Update current BSS level when signal change event occurs
When an EVENT_SIGNAL_CHANGE occurs the bgscan is informed about this
change but the new RSSI value is not stored. In consequence, when
roaming candidates are evaluated, the RSSI value of the current BSS used
to compare is an old one obtained during the last scan rather than the
new one given by the signal change event. This leads sometimes to bad
decision when selecting a new BSS for roaming.

This patch solves the issue by updating the current BSS level when
receiving a signal change event in order to have a very up-to-date
current signal value when choosing an new BSS.

Signed-off-by: Matthieu Mauger <matthieux.mauger@intel.com>
2015-02-21 16:07:53 +02:00
Ilan Peer
f1609f119a wpa_supplicant: Cancel sched_scan when stopping countermeasures
When stopping the TKIP countermeasures, it would be preferable to
connect immediately. However if scheduled scan is in progress,
a connection attempt will be done only when scan results are received,
so cancel the scheduled scan to allow immediate scan and connection
attempt.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-02-21 16:07:53 +02:00
Jouni Malinen
b0e669beeb P2P: Fix P2P_CONNECT-auto fallback to GO Neg with group interface
If a separate P2P group interface was used, P2P_CONNECT-auto fallback to
GO Negotiation could result in use of freed memory and segmentation
fault. This happened in cases where the peer GO was found in some old
scans, but not in the first scan triggered by the P2P_CONNECT-auto
command ("P2P: Peer was found running GO in older scan -> try to join
the group" shows up in the debug log). In addition, the GO would still
need to reply to PD Request to allow this code path to be triggered.

When five scans for the GO were completed in this sequence, the P2P
group interface was removed as part of falling back to GO Negotiation.
However, that ended up dereferencing the freed wpa_s instance at the end
of scan event processing. Fix this by reordering code a bit and breaking
out from EVENT_SCAN_RESULTS processing if the interface could have been
removed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:35:14 +02:00
Jouni Malinen
ba4226130e Simplify eapol_sm_notify_pmkid_attempt()
Drop the unneeded 'attempt' argument. This was originally used for
indicating an aborted PMKID caching attempt, but a fix in 2006 removed
the only such user and since that time, only attempt == 1 has been used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-28 13:09:31 +02:00
Jouni Malinen
3f56a2b746 Ignore pmf=1 default if driver does not support PMF
Connection with a PMF enabled AP will fail if we try to negotiate PMF
while the local driver does not support this. Since pmf=1 does not
require PMF for a successful connection, it can be ignored in such a
case to avoid connectivity issues with invalid configuration. This makes
it somewhat easier to allow upper layer programs to use pmf=1 default
regardless of driver capabilities.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 12:38:52 +02:00
Jouni Malinen
98cd3d1c3b Preparations for variable length KCK and KEK
This modifies struct wpa_ptk to allow the length of KCK and KEK to be
stored. This is needed to allow longer keys to be used, e.g., with
Suite B 192-bit level.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 01:26:49 +02:00
Ben Rosenfeld
d90bfa97f4 Move external_scan_running to wpa_radio
external_scan_running should be common to all interfaces that share a
radio. This fixes a case where external_scan_running was set on a single
interface, but did not block scan on other interfaces.

Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
2015-01-20 01:57:59 +02:00
Stefan Tomanek
79cd993a62 Add address masks to BSSID lists
In many applications it is useful not just to enumerate a group of well
known access points, but to use a address/mask notation to match an
entire set of addresses (ca:ff:ee:00:00:00/ff:ff:ff:00:00:00).

This change expands the data structures used by MAC lists to include a
mask indicating the significant (non-masked) portions of an address and
extends the list parser to recognize mask suffixes.

Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
2015-01-10 17:35:53 +02:00
Stefan Tomanek
b83e455451 Add network specific BSSID black and white lists
This change adds the configuration options "bssid_whitelist" and
"bssid_blacklist" used to limit the AP selection of a network to a
specified (finite) set or discard certain APs.

This can be useful for environments where multiple networks operate
using the same SSID and roaming between those is not desired. It is also
useful to ignore a faulty or otherwise unwanted AP.

Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
2015-01-10 17:35:53 +02:00
Jouni Malinen
635874b55a Handle interface disabled/enabled more consistently
It was possible for the interface not to be marked in INTERFACE_DISABLED
state in case the event was processed for P2P GO because the wpa_s
instance could have been removed in case of a separate group interface.
Change the state first to avoid leaving different state for the case
where separate group interface is not used.

Mark scan to be a normal scan on INTERFACE_ENABLED so that scanning
rules (e.g., skip scan if no networks enabled) get used consistently.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-08 22:43:48 +02:00
Jouni Malinen
8f2cf37923 P2P: Indicate reason=UNAVAILABLE for group netdev going down
There is a race condition between receiving an AP stopped event and
netdev down event. These resulted in different group removal reasons on
a GO device (UNAVAILABLE for stop AP event coming first and REQUESTED
for netdev event first). Make this more consistent by reporting
UNAVAILABLE for both possible cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-08 22:43:48 +02:00
Eliad Peller
8c42b36902 WMM AC: Reconfigure tspecs on reassociation to the same BSS
The specification requires the tspecs to be kept upon reassociation to
the same BSS. Save the last tspecs before such reassociation, and
reconfigure on the association notification.

Note that the current flow is not transparent to the user
(it is notified about deauth/reassoc and tspec removal/addition).

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2015-01-04 18:41:00 +02:00
Eliad Peller
fecc2bb5a8 WMM AC: Delete tspecs on roaming
In case of roaming, we don't get disassoc notification, but
still want to remove the existing tspecs.

Move the wmm_ac_notify_disassoc() call to the state change
function, which get called also on roaming.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2015-01-04 18:32:59 +02:00
Jouni Malinen
4e70bbf1c6 SAE: Clear keys from memory on disassociation
There is no need to keep temporary keys in memory beyond the end of the
association, so explicitly clear any SAE buffers that can contain keys
as soon as such keys are not needed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-29 20:00:02 +02:00
Jouni Malinen
9a700ff9ef Ignore auth/assoc timeout events in mesh configuration
It was possible for auth/assoc timeout/failure event from the driver to
result in unexpected processing during mesh group setup if that
operation was started before the previously started driver operation to
association/connect had completed. Since those events cannot happen in
mesh cases, ignore them to avoid issues due to this corner case.

For example, monitor_iface_unknown_sta followed by wpas_mesh_secure test
case resulted in failure without this change.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-30 15:53:11 +02:00
Andrei Otcheretianski
70d1e72849 wpa_supplicant: Handle link measurement requests
Send link measurement response when a request is received. Advertise
only RCPI, computing it from the RSSI of the request. The TX power field
is left to be filled by the driver. All other fields are not published.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-11-22 21:45:07 +02:00
Assaf Krauss
d89c0701db wpa_supplicant: Add support for Neighbor Report
Add the ability to send a Neighbor Report Request (part of
RRM). Requester is then notified once the report arrives.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:23:14 +02:00
Assaf Krauss
b361d580ec SME: Add RRM support to association request
In case the AP we are associating with advertises support for RRM,
advertise our own RRM support in the (Re)Association Request frame. This
is done by adding an RRM Capabilities IE. The underlying driver is
expected to further add a Power Capabilities IE to the request, and set
the Radio Measurement flag in the Capability Info field. At this point
the RRM Capabilities IE advertises no measurement support.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:13:45 +02:00
Jouni Malinen
75d65857d5 WNM: Use recent scan results on BSS transition request
If the last scans are recent (for now, less than ten seconds old), use
them instead of triggering a new scan when a BSS Transition Management
Request frame is received. As a fallback, allow a new scan to be
triggered if no matches were found.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-22 20:17:47 +02:00