The driver-based SME case did not set STA flags properly to the kernel
in the way that hostapd-SME did in ieee802_11.c. This resulted in the FT
protocol case not marking the STA entry authorized. Fix that by handling
the special WLAN_AUTH_FT case in hostapd_notif_assoc() and also add the
forgotten hostapd_set_sta_flags() call to synchronize these flag to the
driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows updating roaming policy for drivers that select the BSS
internally so that wpa_supplicant (based on bssid parameter
configuration) and the driver remain in sync.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The network block bssid parameter can be used to force a specific BSS to
be used for a connection. It is also possible to modify this parameter
during an association. Previously, that did not result in any
notification to the driver which was somewhat problematic with drivers
that take care of BSS selection. Add a new mechanism to allow
wpa_supplicant to provide a driver update if the bssid parameter change
for the current connection modifies roaming policy (roaming
allowed/disallowed within ESS).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a TX status event and RX event for a GO Negotiation frame gets
delayed long enough to miss the initial wait, it was possible for
reception of a GO Negotiation Response frame with status 1 to try to
initiate a new p2p-listen work item to wait for the peer to become ready
while a previous p2p-listen was already in progress due to that earlier
timeout while waiting for peer. This would result in the new
start_listen request getting rejected ("P2P: Reject start_listen since
p2p_listen_work already exists") and the negotiation not proceeding.
Work around this by using P2P_WAIT_PEER_CONNECT state instead of
P2P_WAIT_PEER_IDLE if P2P_CONNECT_LISTEN state has already been entered
when processing this special GO Negotiation Response status=1 case. This
can avoid double-scheduling of p2p-listen and as such, completion of the
GO negotiation even if the driver event or peer response are not
received in time (the response is supposed to be there within 100 ms per
spec, but there are number of deployed devices that do not really meet
this requirement).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
An interoperability issue with a deployed AP has been identified where
the connection fails due to that AP failing to operate correctly if
PMKID is included in the Association Request frame. To work around this,
allow EAPOL-Start packet to be transmitted on startWhen reaching 0 even
when trying to use PMKSA caching. In practice, this allows fallback to
full EAP authentication if the AP/Authenticator takes more than 1-2
seconds to initiate 4-way handshake for PMKSA caching or full EAP
authentication if there was no PMKSA cache match.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the shorter startWhen value was used based on build
parameters (i.e., if WPS was enabled). This is not really ideal and the
knowledge of WPS use can be provided to the EAPOL state machine to allow
this (and similar WPS workarounds) to be done only when the association
is for the purpose of WPS.
Reduce the default startWhen value from 3 to 2 seconds for non-WPS case
since WPS builds have likely received most testing for the past years
with the 1 second value and there is no strong justification for forcing
the longer 3 second wait should a frame be lost or something else
require the EAPOL-Start to initiate operation after a connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The internal entropy pool was previously used to prevent 4-way handshake
in AP mode from completing before sufficient entropy was available to
allow secure keys to be generated. This commit extends that workaround
for boards that do not provide secure OS level PRNG (e.g., /dev/urandom
does not get enough entropy) for the most critical WPS operations by
rejecting AP-as-enrollee case (use of AP PIN to learn/modify AP
configuration) and new PSK/passphrase generation. This does not have any
effect on devices that have an appropriately working OS level PRNG
(e.g., /dev/random and /dev/urandom on Linux).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Currently to signal PropertiesChanged upon group client
removal (group property), wpa_supplicant dbus uses wpa_s
members like go_dev_addr and current_ssid, for instance.
Thus, deferring p2p client deauth to after dbus notify,
but keeping the same order as before, solves the issue,
as wpa_s is not yet completely deinitialized.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
Even when hs20 action frame is unable to be registered,
for whatever reason, it should be possible to register
event handle for received driver messages. This patch also
avoids a segmentation fault, when p2p and hs20 were enabled
and GO NEG was unable to create p2p iface, the destroy eloop
was crashing by reading an invalid handle.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
"Age" is the age in seconds since the BSS was last seen, and is
emitted as a PropertyChanged signal whenever the BSS is updated
from a scan result. It also returns the correct age when queried
directly.
This property can be used to resolve issues where, if no other
properties of the BSS changed from scan results (for example,
if the BSS always had 100% signal) no D-Bus signals would be
emitted to indicate that the BSS had just been seen in the scan.
Signed-hostap: Dan Williams <dcbw@redhat.com>
Copy-paste error ended up getting rsn_pairwise_cipher value for both
rsn_pairwise_cipher and wpa_pairwise_cipher (CID 72693).
Signed-off-by: Jouni Malinen <j@w1.fi>
In theory, this function could fail, so check the return value before
printing out the RADIUS local address debug message (CID 72700).
Signed-off-by: Jouni Malinen <j@w1.fi>
Due to a missing curly brackets, the OCSP status checking was not
working in the expected way. Instead of allowing optional-OCSP
configuration to accept connection when OCSP response was ready, all
such cases were marked as hard failures. In addition, the debug prints
were not necessarily accurate for the mandatory-OCSP-but-no-response
case (CID 72694, CID 72704).
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of using implicit limit based on 16-bit unsigned integer having
a maximum value of 65535, limit the maximum length of a CID explicitly
to 1500 bytes. This will hopefully help in reducing false warnings from
static analyzers (CID 72712).
Signed-off-by: Jouni Malinen <j@w1.fi>
The local bss variable is used only within the while loop, so no need to
assign or even make it visible outside the loop.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
TDLS Setup Request frame has to be rejected with status code 37 ("The
request has been declined"), if the BSSID in the received Link
Identifier does not match the current BSSID per IEEE Std 802.11-2012,
10.22.4 ('TDLS direct-link establishment') step (b). The previously used
status code 7 ('Not in same BSS') is described to used only when
processing TPK Handshake Message 2 in TDLS Setup Response frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While building Association Request frame IEs we should consider adding
P2P IEs only on interface where P2P functionality is enabled. Consider
per interface p2p_disabled parameter before adding P2P IEs to complete
the checks for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When a netdev is removed from a bridge, RTM_DELLINK message is received
with ifname (IFLA_IFNAME) pointing to the main netdev event though that
netdev is not deleted. This was causing issues with P2P GO interface
getting disabled when the netdev was removed from a bridge. Fix this by
filtering RTM_DELLINK events that are related to the bridge when
indicating interface status changes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some deployed APs send two credentials when in mixed-WPA/WPA2
configuration; one for the WPA-Personal/TKIP and the other for
WPA2-Personal/CCMP. Previously, this would result in two network blocks
getting added for the single AP. This can be somewhat confusing and
unnecessary, so merge such credentials into a single one that allows
both WPA and WPA2 to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add NULL checks to take care of issues reported by static analyzer tool
on potentially using NULL with printf format %s (which has undefined
behavior even though many compilers end up printing "(null)").
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the P2P Interface Address of the peer gets updated in the
peer table every time based on the scan results.
For example, in a two port concurrency scenario, where the peer device
has two interfaces with unique P2P Interface Addresses and with same P2P
Device Address, based on the Probe Response/Beacon frames from these two
interfaces, their peer table gets updated, but each of these updates
happens in the peer table only based on the P2P Device Address. So, the
same peer's P2P Interface address is updated every time and hence, at
any instant, only one P2P Device Address to P2P Interface Address
mapping entry exist in the peer table for the peer which has two
interfaces.
When we try to join a group operated by the peer, lookup happens in the
peer table and when an interface entry is not available, the pending
interface address gets overwritten with the P2P Device Address and hence
the P2P connection can fail. Since the BSS table is the one that is
up-to-date, this fix will ensure that the interface overwriting will
happen only when there is no BSS entry for the pending P2P Interface
Address as well.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While hostapd should not really receive the EVENT_ASSOC message for
IBSS, driver_nl80211.c could potentially generate that if something
external forces the interface into IBSS mode and the IBSS case does not
provide the struct assoc_info data. Avoid the potential NULL pointer
dereference by explicitly verifying for the event data to be present.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Global freq_list scan filtar was taken into account only by
req_scan and not by req_sched_scan. We want to allow the user
to limit the channels that wpa_supplicant will scan in req_sched_scan
requests as well.
Signed-off-by: Bojan Prtvar <bojan.prtvar@rt-rk.com>
Before fixing this issue, calling wpas_dbus_getter_p2p_device_config
was causing early termination of dbus connection, due to writing
values to an already closed dict.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
Disable Probe Request reporting for statically created AP interfaces
during de-initialization. We will enable it again while starting AP
operations.
Signed-off-by: Avinash Patil <avinashapatil@gmail.com>
Some devices have limitations which do not allow changing virtual
interface mode from AP to station or vice versa. To work around this,
check if such AP interface is not dynamic. If such an interface is
enumarated, just set ifmode to AP and avoid setting nlmode to default
station mode on deinit.
Signed-off-by: Avinash Patil <avinashapatil@gmail.com>
In order to find a GO interface, there has to be a
comparison among two SSIDs, instead of a wpa_ssid and
a ssid.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
This adds hostapd support for the new WLAN-Pairwise-Cipher,
WLAN-Group-Cipher, WLAN-AKM-Suite, and WLAN-Group-Mgmt-Pairwise-Cipher
attributes defined in RFC 7268. These attributes are added to RADIUS
messages when the station negotiates use of WPA/RSN.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds hostapd support for the new WLAN-HESSID attribute defined in
RFC 7268. This attribute contains the HESSID and it is added whenever
Interworking is enabled and HESSID is configured.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds hostapd support for the new Mobility-Domain-Id attribute
defined in RFC 7268. This attribute contains the mobility domain id and
it is added whenever the station negotiates use of FT.
Signed-off-by: Jouni Malinen <j@w1.fi>
First for better concistancy but also to tell about the group_object
that is getting removed, thus the client will know about it and will be
able to act accordingly.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
