For now, this is done only for the case where the NFC Device is not
usable and if writing a single tag fails.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make the debug output easier to read when performing interactive NFC
operations on a device that has a terminal showing the log.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The change to checking DPP_LISTEN return value ended up overwriting the
actual URI information from wpas_get_nfc_uri().
Fixes: 288c0ffaaa ("dpp-nfc: Do not hardcode netrole for NFC Tag writing cases")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow netrole to be specified for NFC Tag writing cases. Previously,
this was hardcoded to use netrole=configurator when starting the listen
operation. Now the netrole parameter is not included by default, but any
netrole value can be specified with the new --netrole command line
argument.
In addition, fix the listening frequency for the case where a channel is
picked.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduce a new attribute QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE
to configure access category override for UDP frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Introduces a vendor command to get the currently enabled band(s)
through QCA_NL80211_VENDOR_SUBCMD_GETBAND.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Also introduce a new attribute QCA_WLAN_VENDOR_ATTR_SETBAND_MASK to
carry this new bitmask enum. This attribute shall consider the bitmask
combinations to define the respective band combinations and substitutes
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE. The old attribute use remains same
as before.
In addition, document the previously undocumented, but defined,
QCA_NL80211_VENDOR_SUBCMD_SETBAND.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The NL80211_ATTR_VLAN_ID attribute expects non-zero values, but vlan_id
with value 0 has been set in VLAN offload case. Due to this, station
connection failure is observed if the driver advertises VLAN_OFFLOAD
support:
nl80211: NL80211_ATTR_STA_VLAN (addr=8c:fd:f0:22:19:15 ifname=wlan0
vlan_id=0) failed: -34 (Result not representable)
wlan0: STA 8c:fd:f0:22:19:15 IEEE 802.11: could not bind the STA
entry to vlan_id=0
Fix this by setting only non-zero values.
Fixes: 0f903f37dc ("nl80211: VLAN offload support")
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
40/80 MHz bandwidth setting was being rejected due to incorrect sanity
check on the channel index. Fix that for the bandwidths larger than 20
MHz.
Fixes: d7c2c5c98c ("AP: Add initial support for 6 GHz band")
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
When removing a mesh peer with control interface commands (ACCEPT_ACL
DEL_MAC/DENY_ACL ADD_MAC/MESH_PEER_REMOVE) the plink count was not
decreased from its last connection. This resulted in peer link count
leakage and wpa_supplicant rejecting the connections after reaching
max_peer_links (default: 99).
Fix this by decreasing the plink count when removing a mesh peer which
is in PLINK_ESTAB state.
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
wpa_s->dpp_auth did not get cleaner if dpp_config_processing=1 is used.
Clear this after having received TX status for Configuration Result to
avoid leaving behind the completed provisioning instance.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The pending authentication exchange will make us ignore Reconfig
Authentication Request, so do not allow reconfiguration to be started in
that state.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The 0..3 value decoded from the password was not incremented to the
actual 2..5 range for Sec. This resulted in not properly detecting the
minimum password length.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The use of the alternative channel list did not work properly for the
case were both ends were trying to initiate the negotiated connection
handover. Fix this by always starting a new connection handover client
thread for sending the alternative proposal and ignoring peer messages
(likely something from the first attempt) during this modified attempt.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When a PMKSA cache entry is available and used for connection with FILS
key management suite, use FILS authentication algorithm for connection
even if ERP keys are not available. This scenario may happen when
applications using wpa_supplicant cache persistently only PMKSA but not
ERP keys and reconfigures wpa_supplicant with PMKSA cache after
restarting wpa_supplicant.
The previous implementation correctly handles SME-in-wpa_supplicant
cases. However, SME-in-driver cases, complete FILS authentication
without PMKSA caching is performed.
Fix SME-in-driver behavior by setting authentication algorithm to
WPA_AUTH_ALG_FILS when connecting to a FILS AP using PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The channel numbering/center frequencies was changed in IEEE
P802.11ax/D6.1. The center frequencies of the channels were shifted by
10 MHz. Also, a new operating class 136 was defined with a single
channel 2. Add required support to change the channelization as per IEEE
P802.11ax/D6.1.
Signed-off-by: Wu Gao<wugao@codeaurora.org>
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
If the peer's channel list in negotiated handover does not have any
common channels and the local end is configured with an alternative
channel list, try to initiate another negotiation handover with the
alternative channels.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Be clearer about only a tag read being allowed when dpp-nfc is
configured to not allow connection handover.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This fixes an issue where the pending authentication might have held a
reference to auth->tmp_peer_bi and dpp_auth_deinit() would try to free
that bootstrapping entry. This needs to happen before the call to
dpp_global_clear() to avoid double-removal of the bootstrapping entry
from the list.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check if nl80211 control port TX status is available in the kernel and
enable control port TX if so. With this feature, nl80211 control path is
able to provide the same feature set as nl80211 (management) + AF_PACKET
socket (control) before.
For debugging and testing, this can explicitly be disabled with
the driver parameter control_port_ap=0.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
The kernel commit "mac80211: support control port TX status reporting"
seems to be delivering the TX status events for EAPOL frames over
control port using NL80211_CMD_FRAME_TX_STATUS due to incorrect check on
whether the frame is a Management or Data frame. Use the pending cookie
value from EAPOL TX operation to detect this incorrect behavior and
redirect the event internally to allow it to be used to get full TX
control port functionality available for AP mode.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow custom ack handler to be registered and use the ext ack handler
for TX control port to fetch the cookie information. If these cookies
are not supported by the current kernel, a value of 0 is returned.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
In order to retransmit faster in AP mode, hostapd can handle TX status
notifications. When using nl80211, this is currently only possible with
socket control messages. Add support for receiving such events directly
over nl80211 and detecting, if this feature is supported.
This finally allows for a clean separation between management/control
path (over nl80211) and in-kernel data path.
A follow up commit enables the feature in AP mode.
Control port TX status contains the original frame content for matching
with the current hostapd code. Furthermore, a cookie is included, which
allows for matching against outstanding cookies in the future. This
commit only prints the cookie value for debugging purposes on TX status
receive.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
This is a preliminary patch for using extack cookies for TX control port
handling. Custom ack handler arguments for send_and_recv() and friends
is introduced therefore. This commit does not actually use the provided
values, i.e., that will be added in a separate commit.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
eap_teap_auth=2 can now be used to configure hostapd to skip Phase 2 if
the peer can be authenticated based on client certificate during Phase
1.
Signed-off-by: Jouni Malinen <j@w1.fi>
The EAP-TEAP server may skip Phase 2 if the client authentication could
be completed during Phase 1 based on client certificate. Handle this
similarly to the case of PAC use.
Signed-off-by: Jouni Malinen <j@w1.fi>
These are needed for EAP-TEAP server and client side implementation to
allow Phase 2 to be skipped based on client certificate use during Phase
1.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add events for within-ESS reassociation. This allows us to monitor roam
events, both skipped and allowed, in tests.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Pull all the within-ESS roam code out of wpa_supplicant_need_to_roam()
and into its own function, wpa_supplicant_need_to_roam_within_ess().
This way, we avoid interleaving several #ifndef's in the original
function and wrap the new function in one big #ifndef. This also
modularizes the within-ESS roam code and makes it easier to test.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Instead of overriding the subject field with something arbitrary, use
the value that is included in the CSR now that there is something there.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Jouni Malinen