It was possible for the p2p_go_neg_start timeout handler to get called
when there was a pending timeout from an earlier GO Negotiation start.
This could result in that old timeout expiring too early for the newly
started GO Negotiation to complete. Avoid such issues by setting a
sufficiently long timeout here just before triggering the new GO
Negotiation.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, it was possible for the p2p->pending_listen_freq to be left
at non-zero value if Probe Request frame was received from a peer with
which we were waiting to start GO Negotiation/Invite process. That could
result in the following Listen operation getting blocked in some
operation sequences if the peer did not acknowledge the following P2P
Public Action frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, extra connect/roam events were ignored when user space SME
was used to avoid confusing double events for association. However,
there was no matching code for ignoring auth/assoc events when using
driver SME. Such events would not normally show up since the driver SME
case would not generated them. However, when testing forced connect
command with force_connect_cmd=1 driver param, these events are
indicated.
Ignore the extra events in testing cases to make the hwsim test cases
match more closely the real code path for driver SME. In addition, this
resolves some test case failures where double association event could
end up causing a failure, e.g., when doing PMKSA caching in
pmksa_cache_oppurtunistic_connect.
Signed-off-by: Jouni Malinen <j@w1.fi>
This fixes couple of code paths where the WPA_DRIVER_FLAGS_DFS_OFFLOAD
flag was not checked properly and unexpected DFS operations were
initiated (and failed) in case the driver handles all these steps.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In theory, this call could fail, so check the return value before using
the received data. These specific cases would not really care much about
the failures, but this keeps the code more consistent and keeps static
analyzer warnings more useful. (CID 72678, CID 72679, CID 72680,
CID 72683, CID 72689, CID 72698, CID 72703)
Signed-off-by: Jouni Malinen <j@w1.fi>
The driver-based SME case did not set STA flags properly to the kernel
in the way that hostapd-SME did in ieee802_11.c. This resulted in the FT
protocol case not marking the STA entry authorized. Fix that by handling
the special WLAN_AUTH_FT case in hostapd_notif_assoc() and also add the
forgotten hostapd_set_sta_flags() call to synchronize these flag to the
driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows updating roaming policy for drivers that select the BSS
internally so that wpa_supplicant (based on bssid parameter
configuration) and the driver remain in sync.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The network block bssid parameter can be used to force a specific BSS to
be used for a connection. It is also possible to modify this parameter
during an association. Previously, that did not result in any
notification to the driver which was somewhat problematic with drivers
that take care of BSS selection. Add a new mechanism to allow
wpa_supplicant to provide a driver update if the bssid parameter change
for the current connection modifies roaming policy (roaming
allowed/disallowed within ESS).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a TX status event and RX event for a GO Negotiation frame gets
delayed long enough to miss the initial wait, it was possible for
reception of a GO Negotiation Response frame with status 1 to try to
initiate a new p2p-listen work item to wait for the peer to become ready
while a previous p2p-listen was already in progress due to that earlier
timeout while waiting for peer. This would result in the new
start_listen request getting rejected ("P2P: Reject start_listen since
p2p_listen_work already exists") and the negotiation not proceeding.
Work around this by using P2P_WAIT_PEER_CONNECT state instead of
P2P_WAIT_PEER_IDLE if P2P_CONNECT_LISTEN state has already been entered
when processing this special GO Negotiation Response status=1 case. This
can avoid double-scheduling of p2p-listen and as such, completion of the
GO negotiation even if the driver event or peer response are not
received in time (the response is supposed to be there within 100 ms per
spec, but there are number of deployed devices that do not really meet
this requirement).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the shorter startWhen value was used based on build
parameters (i.e., if WPS was enabled). This is not really ideal and the
knowledge of WPS use can be provided to the EAPOL state machine to allow
this (and similar WPS workarounds) to be done only when the association
is for the purpose of WPS.
Reduce the default startWhen value from 3 to 2 seconds for non-WPS case
since WPS builds have likely received most testing for the past years
with the 1 second value and there is no strong justification for forcing
the longer 3 second wait should a frame be lost or something else
require the EAPOL-Start to initiate operation after a connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The internal entropy pool was previously used to prevent 4-way handshake
in AP mode from completing before sufficient entropy was available to
allow secure keys to be generated. This commit extends that workaround
for boards that do not provide secure OS level PRNG (e.g., /dev/urandom
does not get enough entropy) for the most critical WPS operations by
rejecting AP-as-enrollee case (use of AP PIN to learn/modify AP
configuration) and new PSK/passphrase generation. This does not have any
effect on devices that have an appropriately working OS level PRNG
(e.g., /dev/random and /dev/urandom on Linux).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Even when hs20 action frame is unable to be registered,
for whatever reason, it should be possible to register
event handle for received driver messages. This patch also
avoids a segmentation fault, when p2p and hs20 were enabled
and GO NEG was unable to create p2p iface, the destroy eloop
was crashing by reading an invalid handle.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
In theory, this function could fail, so check the return value before
printing out the RADIUS local address debug message (CID 72700).
Signed-off-by: Jouni Malinen <j@w1.fi>
Due to a missing curly brackets, the OCSP status checking was not
working in the expected way. Instead of allowing optional-OCSP
configuration to accept connection when OCSP response was ready, all
such cases were marked as hard failures. In addition, the debug prints
were not necessarily accurate for the mandatory-OCSP-but-no-response
case (CID 72694, CID 72704).
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of using implicit limit based on 16-bit unsigned integer having
a maximum value of 65535, limit the maximum length of a CID explicitly
to 1500 bytes. This will hopefully help in reducing false warnings from
static analyzers (CID 72712).
Signed-off-by: Jouni Malinen <j@w1.fi>
TDLS Setup Request frame has to be rejected with status code 37 ("The
request has been declined"), if the BSSID in the received Link
Identifier does not match the current BSSID per IEEE Std 802.11-2012,
10.22.4 ('TDLS direct-link establishment') step (b). The previously used
status code 7 ('Not in same BSS') is described to used only when
processing TPK Handshake Message 2 in TDLS Setup Response frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When a netdev is removed from a bridge, RTM_DELLINK message is received
with ifname (IFLA_IFNAME) pointing to the main netdev event though that
netdev is not deleted. This was causing issues with P2P GO interface
getting disabled when the netdev was removed from a bridge. Fix this by
filtering RTM_DELLINK events that are related to the bridge when
indicating interface status changes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While hostapd should not really receive the EVENT_ASSOC message for
IBSS, driver_nl80211.c could potentially generate that if something
external forces the interface into IBSS mode and the IBSS case does not
provide the struct assoc_info data. Avoid the potential NULL pointer
dereference by explicitly verifying for the event data to be present.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Disable Probe Request reporting for statically created AP interfaces
during de-initialization. We will enable it again while starting AP
operations.
Signed-off-by: Avinash Patil <avinashapatil@gmail.com>
Some devices have limitations which do not allow changing virtual
interface mode from AP to station or vice versa. To work around this,
check if such AP interface is not dynamic. If such an interface is
enumarated, just set ifmode to AP and avoid setting nlmode to default
station mode on deinit.
Signed-off-by: Avinash Patil <avinashapatil@gmail.com>
This adds hostapd support for the new WLAN-Pairwise-Cipher,
WLAN-Group-Cipher, WLAN-AKM-Suite, and WLAN-Group-Mgmt-Pairwise-Cipher
attributes defined in RFC 7268. These attributes are added to RADIUS
messages when the station negotiates use of WPA/RSN.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds hostapd support for the new WLAN-HESSID attribute defined in
RFC 7268. This attribute contains the HESSID and it is added whenever
Interworking is enabled and HESSID is configured.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds hostapd support for the new Mobility-Domain-Id attribute
defined in RFC 7268. This attribute contains the mobility domain id and
it is added whenever the station negotiates use of FT.
Signed-off-by: Jouni Malinen <j@w1.fi>
The special PAC_OPAQUE_TYPE_PAD case did not skip incrementing of the
pos pointer and could result in one octet read-after-buffer when parsing
the PAC-Opaque data.
Signed-off-by: Jouni Malinen <j@w1.fi>
This forces EAP peer implementation to drop any possible fast resumption
data if the network block for the current connection is not the same as
the one used for the previous one. This allows different network blocks
to be used with non-matching parameters to enforce different rules even
if the same authentication server is used. For example, this allows
different CA trust rules to be enforced with different ca_cert
parameters which can prevent EAP-TTLS Phase 2 from being used based on
TLS session resumption.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is similar to wpa_msg_global() in the same way as wpa_msg_ctrl() is
to wpa_msg(). In other words, wpa_msg_global_ctrl() is used to send
global control interface events without printing them into the debug
log.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use an explicit memset call to clear any configuration parameter and
dynamic data that contains private information like keys or identity.
This brings in an additional layer of protection by reducing the length
of time this type of private data is kept in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the EAP-pwd server and peer implementations more robust
should OpenSSL fail to derive random number for some reason. While this
is unlikely to happen in practice, the implementation better be prepared
for this should something unexpected ever happen. See
http://jbp.io/2014/01/16/openssl-rand-api/#review-of-randbytes-callers
for more details.
Signed-off-by: Florent Daigniere <nextgens@freenetproject.org>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Florent Daigniere <nextgens@freenetproject.org>
This changes OpenSSL calls to explicitly clear the EC_POINT memory
allocations when freeing them. This adds an extra layer of security by
avoiding leaving potentially private keys into local memory after they
are not needed anymore. While some of these variables are not really
private (e.g., they are sent in clear anyway), the extra cost of
clearing them is not significant and it is simpler to just clear these
explicitly rather than review each possible code path to confirm where
this does not help.
Signed-off-by: Florent Daigniere <nextgens@freenetproject.org>
This changes OpenSSL calls to explicitly clear the bignum memory
allocations when freeing them. This adds an extra layer of security by
avoiding leaving potentially private keys into local memory after they
are not needed anymore. While some of these variables are not really
private (e.g., they are sent in clear anyway), the extra cost of
clearing them is not significant and it is simpler to just clear these
explicitly rather than review each possible code path to confirm where
this does not help.
Signed-off-by: Florent Daigniere <nextgens@freenetproject.org>
FreeRADIUS releases before 1.1.4 did not send MS-CHAP2-Success in
EAP-TTLS/MSCHAPv2. A wpa_supplicant workaround for that was added in
2005 and it has been enabled by default to avoid interoperability
issues. This could be disabled with all other EAP workarounds
(eap_workaround=0). However, that will disable some workarounds that are
still needed with number of authentication servers.
Old FreeRADIUS versions should not be in use anymore, so it makes sense
to remove this EAP-TTLS/MSCHAPv2 workaround completely to get more
complete validation of server behavior. This allows MSCHAPv2 to verify
that the server knows the password instead of relying only on the TLS
certificate validation.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
When driver interface is destroyed (via wpa_driver_nl80211_deinit) the
"preq" nl socket isn't always deleted but the callback struct associated
is. After the interface is destroyed we may still get event on the
socket but as the callback has been freed this will cause wpa_supplicant
to crash.
This patch ensures that the "preq" socket is destroyed when destroying
the interface.
Signed-off-by: Cedric IZOARD <cedricx.izoard@intel.com>
This allows external programs to use vendor specific information from
P2P peers without wpa_supplicant having to be able to parse and
understand all such vendor specific elements.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds following new control interface commands to allow arbitrary
vendor elements to be added into number of frames:
VENDOR_ELEM_ADD <frame id> <hexdump of elem(s)>
VENDOR_ELEM_GET <frame id>
VENDOR_ELEM_REMOVE <frame id> <hexdump of elem(s)>
VENDOR_ELEM_REMOVE <frame id> *
The following frames are supported in this commit (additional frames can
be added in the future):
0 = Probe Request frame in P2P device discovery
1 = Probe Response frame from P2P Device role
2 = Probe Response frame from P2P GO
3 = Beacon frame from P2P GO
4 = PD Req
5 = PD Resp
6 = GO Neg Req
7 = GO Neg Resp
8 = GO Neg Conf
9 = Invitation Request
10 = Invitation Response
11 = P2P Association Request
12 = P2P Association Response
One or more vendor element can be added/removed with the commands. The
hexdump of the element(s) needs to contain the full element (id, len,
payload) and the buffer needs to pass IE parsing requirements to be
accepted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
set_dfs_state() return value is not currently checked anywhere, so
remove the dead assignment to avoid static analyzer complaints.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use an explicit memset call to clear any configuration parameter and
dynamic data that contains private information like keys or identity.
This brings in an additional layer of protection by reducing the length
of time this type of private data is kept in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use an explicit memset call to clear any hostapd configuration parameter
that contains private information like keys or identity. This brings in
an additional layer of protection by reducing the length of time this
type of private data is kept in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use an explicit memset call to clear any hs20-osu-client configuration
parameter that contains private information like keys or identity. This
brings in an additional layer of protection by reducing the length of
time this type of private data is kept in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reduce the amount of time keying material (MSK, EMSK, temporary private
data) remains in memory in EAP methods. This provides additional
protection should there be any issues that could expose process memory
to external observers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reduce the amount of time keying material (MSK, EMSK, temporary private
data) remains in memory in EAP methods. This provides additional
protection should there be any issues that could expose process memory
to external observers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use an explicit memset call to clear any wpa_supplicant configuration
parameter that contains private information like keys or identity. This
brings in an additional layer of protection by reducing the length of
time this type of private data is kept in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
The pos pointer is not used after this now nor in future plans, so no
need to increment the value. This remove a static analyzer warning about
dead increment.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of using the pre-calculated length of the buffer, determine the
length of used data based on the pos pointer. This avoids a static
analyzer warning about dead increment.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes the implementation less likely to provide useful timing
information to potential attackers from comparisons of information
received from a remote device and private material known only by the
authorized devices.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function is meant for comparing passwords or hash values where
difference in execution time could provide external observer information
about the location of the difference in the memory buffers. The return
value does not behave like os_memcmp(), i.e., os_memcmp_const() cannot
be used to sort items into a defined order. Unlike os_memcmp(),
execution time of os_memcmp_const() does not depend on the contents of
the compared memory buffers, but only on the total compared length.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of using implicit limit based on 16-bit unsigned integer having
a maximum value of 65535, limit the maximum length of a fragmented
EAP-pwd message explicitly to 15000 bytes. None of the supported groups
use longer messages, so it is fine to reject any longer message without
even trying to reassemble it. This will hopefully also help in reducing
false warnings from static analyzers (CID 68124).
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier for static analyzers to figure out which code paths
are possible within eap_sim_msg_finish() for EAP-SIM. This will
hopefully avoid some false warnings (CID 68110, CID 68113, CID 68114).
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the earlier commit e6270129f6
('Clean up EAPOL-Key Key Data processing') design to be used with
PeerKey EAPOL-key processing as well. This avoids false warnings from
static analyzer (CID 62860, CID 62861, CID 62862).
Signed-off-by: Jouni Malinen <j@w1.fi>
This will be useful in wpa_supplicant part to signal if a peer got its
group changed.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
GroupMember is unusable in itself and all the necessary informations are
stored in Peer objects, thus replace the use of GroupMember by Peer.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will be useful in wpa_supplicant to match group's SSIDs against a
specific one.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will be useful for finding the interface related to this group
after formation based on the group SSID.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Use a helper function to avoid multiple copies of the same long list of
argument parameters to wpa_sm_tdls_peer_addset() from the peer entry.
Signed-off-by: Jouni Malinen <j@w1.fi>
Update the peer STA with full info sending TDLS Setup Response/Confirm
frames instead of after the full setup exchange. This makes it easier
for some drivers to properly negotiate QoS and HT information on the
direct link.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
There is no need to keep the peer entry in memory after the link has
been removed.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Tested-by: Ilan Peer <ilan.peer@intel.com>
It's worth giving a try to fallback to re-starting BSSes at least once
hoping it works out instead of just leaving BSSes disabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Currently hostapd data structures aren't ready for multi-channel BSSes,
so make DFS work now at least with single-channel multi-BSS channel
switching.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Fix a bug where changing the mode of the interface to IBSS
fails because the interface is sitting on a channel where IBSS is
disallowed because of a previous association.
Signed-off-by: Christopher Wiley <wiley@chromium.org>
In preparation for another wrinkle around switching into IBSS mode,
refactor existing mode switch logic for simplicity at the expense
of some brevity.
Signed-off-by: Christopher Wiley <wiley@chromium.org>
Previously, eight character random passphrase was generated
automatically for P2P GO. The new p2p_passphrase_len parameter can be
used to increase this length to generate a stronger passphrase for cases
where practicality of manual configuration of legacy devices is not a
concern.
Signed-off-by: Jouni Malinen <j@w1.fi>
Hitting maximum number of AT_KDF attributes could result in an infinite
loop due to the attribute parser not incrementing the current position
properly when skipping the extra KDF.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a local variable and size_t in length comparison to make this easier
for static analyzers to understand. In addition, set the return list and
list_len values at the end of the function, i.e., only in success case.
These do not change the actual behavior of the only caller for this
function, but clarifies what the helper function is doing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use size_t instead of int for storing and comparing the TLV length
against the remaining buffer length to make this easier for static
analyzers to understand.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was added by commit 8a45811638
('hostapd: Add Operating Mode Notification support'), but the validation
steps cannot be true either for the channel width (which is a two-bit
subfield that cannot encode more than the list four values) or Rx NSS
(which cannot encode a value larger 7). Furthermore, the VHT_CHANWIDTH_*
defines do not match the definition of the Channel Width subfield
values.
Since this check cannot ever match, it is better to remove it to make
the code easier to understand and to avoid getting complaints about dead
code from static analyzers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some APs (Cisco) may tack on a weird IE to the end of a TDLS Discovery
Request packet. This needn't fail the response, since the required IEs
are verified separately.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Some APs (Cisco) may tack on a weird IE to the end of the TDLS confirm
packet, which can fail negotiation. As an interoperability workaround,
ignore IE parser failures and reject the frame only if any of the
mandatory IEs are not included.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Commit 342bce63cd introduced a possibility
of a NULL pointer dereference on the error path if a new peer entry
fails to get added (i.e., memory allocation failure). Fix that by
skipping the wpa_tdls_peer_free() call if necessary.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit b36935be1a ('nl80211: Fix EAPOL
frames not being delivered') and commit
147848ec4d ('nl80211: Do not add all
virtual interfaces to drv->if_indices') were not fully in sync and it
was possible for some non-hostapd use cases to end up adding undesired
ifindexes into the list of interfaces from which events and EAPOL frames
are processed on the parent interface. This could result, e.g., in P2P
Device management interface on getting unexpected events, including
RTM_NEWLINK event that could end up getting interpreted as an
indication of the interface being down and unavailable.
Make both add_ifidx() calls use the same criteria for adding interfaces
to the local list. This is not really a complete solution, but it is
good enough for now to fix the most visible side effects of this issue.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
The driver might not be able to add the TDLS STA. Fail if this happens.
Also fix the error path to always reset the TDLS peer data.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
If a link is unreachable, the specification mandates we should send a
teardown packet via the AP with a specific teardown reason. Force this
by first disabling the link and only then sending the teardown packet
for the LOW_ACK event.
Rename the TDLS LOW_ACK event handler to better reflect its purpose.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Earlier commit related to MAC address based access control list
offloaded to the driver was not sending ACL configuration to the driver
if the MAC address list was empty. Remove this check as empty access
control list is a valid use case and sending ACL parameters should not
be dependent on whether the list is empty.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Performing a P2P Device flow such as p2p_listen or
p2p_find, can degrade the performance of an active interface
connection, if the listen frequency is different than the
frequency used by that interface.
To reduce the effect of P2P Device flows on other interfaces,
try changing the listen channel of the P2P Device to match the
operating channel of one of the other active interfaces. This change
will be possible only in case that the listen channel is not forced
externally, and will be delayed to a point where the P2P Device
state machine is idle.
The optimization can be configured in the configuration file and
is disabled by default.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
In p2p_get_pref_freq, if the channels argument is NULL, select a
preferred channel that is also one of the P2P Device configured
channels.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Use a single location in wpa_sm_rx_eapol() for preparing the pointer to
the Key Data field and to its validated length instead of fetching that
information in number of processing functions separately.
Signed-off-by: Jouni Malinen <j@w1.fi>
Re-order wpa_sm_rx_eapol() to first go through all EAPOL (802.1X) header
validation steps using the original message buffer and re-allocate and
copy the frame only if this is a valid EAPOL frame that contains an
EAPOL-Key. This makes the implementation easier to understand and saves
unnecessary memory allocations and copying should other types of EAPOL
frames get here.
Signed-off-by: Jouni Malinen <j@w1.fi>
These error messages had an incorrect frame name (likely copy-pasted
from the commit message handler) and couple of typos.
Signed-off-by: Jouni Malinen <j@w1.fi>
While this call cannot really fail, check the return value to be more
consistent with all the other wps_build_wfa_ext() calls.
Signed-off-by: Jouni Malinen <j@w1.fi>
While the hash functions would be very unlikely to fail in practice,
they do have option of returning an error. Check that return value more
consistently.
Signed-off-by: Jouni Malinen <j@w1.fi>
The additional eight octet field was removed from keydatalen without
proper validation of the Key Data Length field. It would have been
possible for an invalid EAPOL-Key frame to be processed in a way that
ends up reading beyond the buffer. In theory, this could have also
resulted in writing beyond the EAPOL-Key frame buffer, but that is
unlikely to be feasible due to the AES key wrap validation step on
arbitrary memory contents.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since there is a limit on the EAP exchange due to maximum number of
roundtrips, there is no point in allowing excessively large buffers to
be allocated based on what the peer device claims the total message to
be. Instead, reject the message if it would not be possible to receive
it in full anyway.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.
Signed-off-by: Jouni Malinen <j@w1.fi>
There seemed to be an off-by-one error in the validation of GAS request
frames. If a Public Action frame without the Action code field would
have reached this function, the length could have been passed as
(size_t) -1 which would likely have resulted in a crash due to reading
beyond the buffer. However, it looks like such frame would not be
delivered to hostapd at least with mac80211-based drivers. Anyway, this
function better be more careful with length validation should some other
driver end up reporting invalid Action frames.
In addition, the Action code field is in a fixed location, so the
IEEE80211_HDRLEN can be used here to clean up bounds checking to avoid
false reports from static analyzer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Action code field is in a fixed location, so the IEEE80211_HDRLEN
can be used here to clean up bounds checking to avoid false reports from
static analyzer.
Signed-off-by: Jouni Malinen <j@w1.fi>
The implementation here was doing what it was supposed to, but the code
was indented in a way that made it quite confusing in the context of a
single line if statement body.
Signed-off-by: Jouni Malinen <j@w1.fi>
In tncc_read_config(), the memory allocted for the config
did not get freed if an error occured.
Signed-off-by: Philippe De Swert <philippe.deswert@jollamobile.com>
The driver may reject offchannel TX operation if the requested wait time
is longer than what the driver indicates as the maximum
remain-on-channel time. Two of the P2P action frame cases used long
enough wait times (1000 ms for DevDisc and 5000 ms for SD) that could go
beyond the limit with some drivers. Fix these to limit the maximum wait
to what the driver indicates as supported.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the set of supported cipher suites to include CCMP-256, GCMP,
GCMP-256, CMAC-256, GMAC, and GMAC-256 when ATH_GCM_SUPPORT=y is set in
the build configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It does not look like there is going to be any additional use for this
old build option that could be used to build the EAP-IKEv2 peer
implementation in a way that interoperates with the eap-ikev2.ccns.pl
project. Remove the workarounds that matches incorrect implementation in
that project to clean up implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
While it does not look like that eapol_sm_get_key() would ever be called
with sm == NULL, the current implementation is inconsistent on whether
that is allowed or not. Check sm != NULL consistently to avoid warnings
from static analyzers.
Signed-off-by: Jouni Malinen <j@w1.fi>
The following kde.rsn_ie_len != peer->rsnie_i_len was already taking
care of enforcing the length to be within the target buffer length.
Anyway, this explicit check makes this clearer and matches the design in
TPK M1 processing.
Signed-off-by: Jouni Malinen <j@w1.fi>
In theory, gmtime() could return NULL if the year value would not fit
into an integer. However, that cannot really happen with the current
time() value in practice. Anyway, clean up static analyzer reports by
checking for this corner case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Must check that UDN was present before trying to parse it. Avoid a NULL
pointer dereference by checking the result before using os_strstr() when
parsing device description from an AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
prev cannot be NULL here in the hostapd_eid_country_add() call since
prev is set whenever start becomes non-NULL. That seems to be a bit too
difficult for some static analyzers, so check the prev pointer
explicitly to avoid false warnings.
Signed-off-by: Jouni Malinen <j@w1.fi>
This fixes an issue where a driver using the deprecated set_ieee8021x()
callback did not include rsn_pairwise bits in the driver configuration
even if mixed WPA+WPA2 configuration was used. This could result, e.g.,
in CCMP not being enabled properly when wpa_pairwise=TKIP and
rsn_pairwise=CCMP was used in the configuration. Fix this by using
bitwise OR of the wpa_pairwise and rsn_pairwise values to allow the
driver to enable all pairwise ciphers.
In addition, make the newer set_ap() driver_ops use the same bitwise OR
design instead of picking between rsn_pairwise and wpa_pairwise. This
makes the code paths consistent and can also fix issues with mixed mode
configuration with set_ap().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the peer provides a username with large part of it being non-ASCII
characters, the previously used buffers may not have been long enough to
include the full string in debug logs and database search due to forced
truncation of the string by printf_encode(). Avoid this by increasing
the buffer sizes to fit in the maximum result.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The off-by-one error in printf_encode() bounds checking could have
allowed buffer overflow with 0x00 being written to the memory position
following the last octet of the target buffer. Since this output is used
as \0-terminated string, the following operation would likely read past
the buffer as well. Either of these operations can result in the process
dying either due to buffer overflow protection or by a read from
unallowed address.
This has been seen to cause wpa_supplicant crash on OpenBSD when control
interface client attaches (debug print shows the client socket address).
Similarly, it may be possible to trigger the issue in RADIUS/EAP server
implementation within hostapd with a suitable constructed user name.
Signed-off-by: Stuart Henderson <sthen@openbsd.org>
If PMF was enabled, the validation step for EAPOL-Key descriptor version
ended up rejecting the message if GCMP had been negotiated as the
pairwise cipher. Fix this by making the GCMP check skipped similarly to
the CCMP case if a SHA256-based AKM is used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Move to PTKINITDONE state and mark PTK valid after successful completion
of FT protocol. This allows the AP/Authenticator to start GTK rekeying
when FT protocol is used. Previously, the station using FT protocol did
not get the new GTK which would break delivery of group addressed
frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
I got the below prints on a particular Android platform:
I/wpa_supplicant( 2637): nl80211: send_and_recv->nl_recvmsgs failed: 20
I/wpa_supplicant( 2637): nl80211: send_and_recv->nl_recvmsgs failed: 20
In JellyBean libnl_2 code, I see that the nl_recvmsgs returns postive values
too. In some cases, nl_recvmgs return the output of nl_recv function. nl_recv
function can return Number of bytes read, 0 or a negative error code.
Looks like this positive return value for nl_recvmsgs may be specific to
Android. While this is not how the API is supposed to work, this does no
harm with upstream libnl which returns only 0 or -1 from the function.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
The dev_found() callback from NFC connection handover message processing
ended up using the p2p_dev_addr pointer that points to the parsed
message. However, that parsed data was freed just before the call. Fix
this by reordering the calls.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the randomly generated bignum does not meet the validation steps, the
iteration loop in sae_get_rand() did not free the data properly. Fix the
memory leak by freeing the temporary bignum before starting the next
attempt at generating the value.
Signed-off-by: Jouni Malinen <j@w1.fi>
Couple of code paths in hostapd.c could have left hapd->drv_priv
pointing to memory that was freed in driver_nl80211.c when a secondary
BSS interface is removed. This could result in use of freed memory and
segfault when the next driver operation (likely during interface
deinit/removal). Fix this by clearing hapd->drv_priv when there is
reason to believe that the old value is not valid within the driver
wrapper anymore.
Signed-off-by: Jouni Malinen <j@w1.fi>
These three calls were used already in three different paths. Use a
helper function to avoid adding even more copies of this.
Signed-off-by: Jouni Malinen <j@w1.fi>
If for some reason interface setup fails mid-way when setting up
multi-BSS AP it was possible to get segmentation fault because driver
was not properly cleaned up.
One possible trigger, when using nl80211 driver, was udev renaming an
interface created by hostapd causing, e.g., linux_set_iface_flags() to
fail.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
This variable is updated when calling hostapd_if_add(), so it makes
sense to do the same thing when calling hostapd_if_remove().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Performing, e.g. `wpa_cli -p /var/run/hostapd raw DISABLE` twice led to
hostapd segmentation fault if multiple BSSes were configured. Fix this
by checking if there is anything to disable at all before trying.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Make sure to not remove interfaces that were not created by
hostapd/wpa_supplicant. This was already done on number of the error
paths, but not all.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
It is possible for the connect() call to fail (e.g., due to unreachable
network based on local routing table), so the current auth/acct_sock may
be left to -1. Use that as an addition trigger to allow server failover
operation to be performed more quickly if it is known that the
retransmission attempt will not succeed anyway.
Signed-off-by: Jouni Malinen <j@w1.fi>
The re-open socket to the current RADIUS server code path did not work
in the expected way here. The pending authentication messages do not
need to be flushed in that case and neither should the retransmission
parameters be cleared. Fix this by performing these operations only if
the server did actually change as a part of a failover operation.
Signed-off-by: Jouni Malinen <j@w1.fi>
The current RADIUS server pointer was updated after each SET command
which broke parsing of multiple RADIUS servers over the control
interface. Fix this by doing the final RADIUS server pointer updates
only once the full configuration is available.
Signed-off-by: Jouni Malinen <j@w1.fi>
Both IPv4 and IPv6 sockets were not closed consistently in the paths
that tried to change RADIUS servers. This could result in leaking
sockets and leaving behind registered eloop events to freed memory on
interface removal.
Signed-off-by: Jouni Malinen <j@w1.fi>
While iterating through RADIUS messages in radius_client_timer(), one
message entry may get flushed by "radius_client_retransmit -->
radius_client_handle_send_error --> radius_client_init_auth -->
radius_change_server --> radius_client_flush". This could result in
freed memory being accessed afterwards.
Signed-off-by: Jerry Yang <xyang@sonicwall.com>
This is one more possible send() error that should trigger RADIUS server
change if multiple servers are configured.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for the RADIUS authentication/accounting socket to not be
open even if partial RADIUS server configuration has been done through
the control interface SET commands. Previously, this resulted in send()
attempt using fd=-1 which fails with bad file descriptor. Clean this up
by logging this as a missing configuration instead of trying to send the
message when that is known to fail.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes invitation process more consistent with GO Negotiation as far
as the debug log entries are concerned and the resulting log is more
helpful for understanding channel selection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of using X509_print_fp() to print directly to stdout, print the
certificate dump to a memory BIO and use wpa_printf() to get this into
the debug log. This allows redirection of debug log to work better and
avoids undesired stdout prints when debugging is not enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This configuration parameter was not used at all in the RADIUS server
implementation and instead, hard coded 0 was sent.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 04eff7d5ba or something around that
timeframe may have caused a regression on how drv->if_indices gets used
with wpa_supplicant. Most (curretly likely all) wpa_supplicant virtual
interface use cases should not actually use this. This could result in
issues with P2P group interfaces delivering events to incorrect
interface (parent rather than the group interface). The previous commit
removed some of the issues, but more complete fix is to undo some of
those merged hostapd/wpa_supplicant operations.
Filter add_ifidx() uses based on hostapd vs. wpa_supplicant and iftype
to get closer to the earlier wpa_supplicant behavior for the driver
events from virtual interfaces.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for a virtual interface to be added and removed by
different parent interfaces. This can happen, e.g., with P2P group
interfaces if the P2P parent interface does not happen to be the first
entry in the wpa_supplicant global interface list. That first entry is
used to remove the group interface while the addition would have
happened with the dedicated P2P management interface.
This can result in the interface that added a new virtual interface
getting stuck with an obsolete ifindex value in the drv->if_indeces list
and as such, deliver some extra events to incorrect destination wpa_s
instance. In particular, this can result in INTERFACE_DISABLED event
from deletion of a P2P group interface getting delivered incorrectly to
the parent wpa_s instance which would disable that interface even though
the interface remains in enabled state.
Fix this by clearing the removed interface from all if_indeces lists
instead of just the one that was used to delete the interface. This is
the simplest approach since the ifindex is unique and there is no need
to track which interface added the new virtual interface to always hit
the same one when removing the interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add regulatory classes for the 60GHz band.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Boris Sorochkin <qca_bsoroc@qca.qualcomm.com>
Instead of silently dropping the response that requires fragmentation,
send an error response to the station to make it aware that no full
response will be available.
Signed-off-by: Jouni Malinen <j@w1.fi>
If p2p_listen is called while previous listen command's
remain_on_channel event is pending, the p2p_listen would fail
and it used to clear pending_listen_freq. Now when the remain-
on-channel event comes from the driver, the pending_listen_freq
doesn't match and gets ignored. This was leading to a case
where listen state was getting stuck (in case of WAIT_PEER_CONNECT
state).
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Previously, the NL80211_ATTR_AKM_SUITES was skipped if either of these
SHA256-based AKMs was negotiated.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
This is similar to the existing functionality that parsed ASN.1-encoded
RSA public key by generating a similar public key instance from already
parsed n and e parameters.
Signed-off-by: Jouni Malinen <j@w1.fi>
Follow the PKCS #1 v1.5, 8.1 constraint of at least eight octets long PS
for the case where the internal TLS implementation decrypts PKCS #1
formatted data. Similar limit was already in place for signature
validation, but not for this decryption routine.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Based on PKCS #1, v1.5, 10.1.3, the block type shall be 01 for a
signature. This avoids a potential attack vector for internal TLS/X.509
implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Verify that there is no extra data after the hash field. This is needed
to avoid potential attacks using additional data to construct a value
that passes the RSA operation and allows the hash value to be forged.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, hostapd had to be started with at least one of the
configuration files enabling TNC for TNC to be usable. Change this to
allow TNC to be enabled when the first interface with TNC enabled gets
added during runtime.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is for enabling easier testing of TNCS/TNCC functionality as part
of the test scripts without having to use the fixed /etc/tnc_config
location that could be used by the main system and would require changes
within /etc.
Signed-off-by: Jouni Malinen <j@w1.fi>
This patch adds epoll option for the eloop implementation. This can be
selected with the CONFIG_ELOOP_EPOLL=y build option.
[merit]
See Table1.
Table1. comparison table
+--------+--------+-----------+------------+-------------+
| | add fd | remove fd | prepare fd | dispatch fd |
+--------+--------+-----------+------------+-------------+
| select | O(1) | O(1) | O(N) | O(N) |
+--------+--------+-----------+------------+-------------+
| poll | O(1) | O(1) | O(N) | O(N) |
+--------+--------+-----------+------------+-------------+
| epoll | O(1) | O(1) | 0 | O(M) |
+--------+--------+-----------+------------+-------------+
"add fd" is addition of fd by eloop_sock_table_add_sock().
"remove fd" is removal of fd by eloop_sock_table_remove_sock().
"prepare fd" is preparation of fds before wait in eloop_run().
"dispatch fd" is dispatchment of fds by eloop_sock_table_dispatch().
"N" is all watching fds.
"M" is fds which could be dispatched after waiting.
As shown in Table1, epoll option has better performance on "prepare fd" column.
Because select/poll option requires setting fds before every select()/poll().
But epoll_wait() doesn't need it.
And epoll option has also better performance on "dispatch fd" column.
Because select/poll option needs to check all registered fds to find out
dispatchable fds. But epoll option doesn't require checking all registered fds.
Because epoll_wait() returns dispatchable fd set.
So epoll option is effective for GO/AP functionality.
[demerit]
The epoll option requires additional heap memory. In case of P2P GO, it is
about 8K bytes.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
p2p_get_pref_freq() went through the full list only if the channels
arguments was provided. If no channel list contraint was in place, the
first pref_chan item was picked regardless of whether it is valid
channel and as such, a later valid entry could have been ignored. Allow
this to loop through all the entries until a valid channel is found or
the end of the pref_chan list is reached. As an extra bonus, this
simplifies the p2p_get_pref_freq() implementation quite a bit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Before starting a 20/40 MHz BSS on the 2.4 GHz band, a 40-MHz-capable HT
AP is required by the rules defined in IEEE Std 802.11-2012 10.15.5 to
examine the channels of the current operational regulatory domain to
determine whether the operation of a 20/40 MHz BSS might unfairly
interfere with the operation of existing 20 MHz BSSs. The AP (or some of
its associated HT STAs) is required to scan all of the channels of the
current regulatory domain in order to ascertain the operating channels
of any existing 20 MHz BSSs and 20/40 MHz BSSs. (IEEE 802.11-2012 S.5.2
Establishing a 20/40 MHz BSS).
Add the check for an overlapping 20 MHz BSS to the initial AP scan for
the P == OT_i case in 10.15.3.2.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
scard_gsm_auth() used SIM_CMD_GET_RESPONSE for both SIM and USIM. Convert
the command into USIM_CMD_GET_RESPONSE for USIM.
Since commit eb32460029 ("Fix switching from EAP-SIM to EAP-AKA/AKA'")
EAP-SIM is using the USIM if available. This triggers a probably ancient
bug in scard_gsm_auth(), which results in sending the wrong get response
command to the USIM. Thus, EAP-SIM stopped to work after this change on
USIMs that expect the proper command.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
If WPS isn't enabled, hostapd_cli returns 'OK' even though WPS doesn't
get activated because WPS context is not valid:
$ hostapd_cli wps_pbc
Selected interface 'wlan0'
OK
$ hostapd_cli wps_cancel
Selected interface 'wlan0'
OK
Fix this by returning appropriate error when WPS fails to activate:
$ hostapd_cli wps_pbc
Selected interface 'wlan0'
FAIL
$ hostapd_cli wps_cancel
Selected interface 'wlan0'
FAIL
Signed-off-by: Petar Koretic <petar.koretic@sartura.hr>
CC: Luka Perkov <luka.perkov@sartura.hr>
Peer should handle a GO Negotiation exchange correctly when the
responding device does not have WSC credentials available at the
time of receiving the GO Negotiation Request. WSC Credentials
(e.g., Pushbutton) can be entered within the 120 second timeout.
Presently, if concurrent session is not active, the peer would wait for
GO Negotiation Request frame from the other device for approximately one
minute due to the earlier optimization change in commit
a2d6365760. To meet the two minute
requirement, replace this design based on number of iterations with a
more appropriate wait for the required number of seconds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the previous commit 0f1034e388 to
skip extended listen also based on ongoing provision discovery operation
(which does not show up as a separate P2P module state and as such, was
not coveraged by the previous commit).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
bss->freq was not updated for IBSS, so whatever old value was stored
from a previous AP mode operation could end up having been used as the
channel when trying to send Authentication frames in an RSN IBSS. This
resulted in the frame not sent (cfg80211 rejects it) and potentially not
being able to re-establish connection due to 4-way handshake failing
with replay counter mismatches. Fix this by learning the operating
channel of the IBSS both when join event is received and when a
management frame is being transmitted since the IBSS may have changed
channels due to merges.
Signed-off-by: Jouni Malinen <j@w1.fi>
RFC 5106 is not exactly clear on the requirements for the "no data"
packet that is used to acknowledge a fragmented message. Allow it to be
processed without the integrity checksum data field since it is possible
to interpret the RFC as this not being included. This fixes reassembly
of fragmented frames after keys have been derived.
Signed-off-by: Jouni Malinen <j@w1.fi>
If invalid group was negotiated, compute_password_element() left some of
the data->grp pointer uninitialized and this could result in
segmentation fault when deinitializing the EAP method. Fix this by
explicitly clearing all the pointer with eap_zalloc(). In addition,
speed up EAP failure reporting in this type of error case by indicating
that the EAP method execution cannot continue anymore on the peer side
instead of waiting for a timeout.
Signed-off-by: Jouni Malinen <j@w1.fi>
The extra data (nonce_s) used in this message was pointing to the
parsed, decrypted data and that buffer was previously freed just before
building the new message. This resulted in use of freed data and
possibly incorrect extra data value that caused the authentication
attempt to fail. Fix this by reordering the code to free the decrypted
data only after the new message has been generated. This was already the
case for EAP-AKA/AKA', but somehow missing from EAP-SIM.
Signed-off-by: Jouni Malinen <j@w1.fi>
The current position pointer was not updated when issuerUniqueID or
subjectUniqueID were present. This could result in extensions being
ignored.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not perform extended listen period operations when either a P2P
connection is in progress. This makes the connection more robust should
an extended listen timer trigger during such an operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Propagate max associated STAs in AP mode advertised by the driver to
core wpa_supplicant implemantion. This allows wpa_supplicant to update
the P2P GO group limit information automatically without having to
configure this limit manually. The information (if available) is also
used in the generic AP implementation to control maximum number of STA
entries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new wowlan_triggers option to wpa_supplicant.conf. The triggers in
this key will be used to configure the kernel wowlan configuration.
For now, support only simple flags. More complex triggers can be added
later on.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Disabling the link only clears the local state. The remote peer will
still think we are connected and disallow the setup.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
When de-authenticating from the AP, disable each TDLS link after
sending the teardown packet. Postpone the reset of the peer state
data until after the link disable request.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Indicate to cfg80211 that interfaces created by the wpa_supplicant
or hostapd are owned by them, and that in case that the socket that
created them closes, these interfaces should be removed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Got segfault, when freeing drv and there exists registered timeout for
blocked rfkill. This patch adds cancel timeout to avoid this.
Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
Commit 96ecea5eb1 did not consider
to pass the VHT/HT/WMM capabilities of the peer for BSS with
open mode.
Address this issue by passing the capabilities irrespective of
the security mode.
Signed-off-by: Pradeep Reddy POTTETI <c_ppotte@qti.qualcomm.com>
If a driver wrapper misbehaves and does not indicate a frame body in the
event, core hostapd code should handle this consistently since that case
was already checked for in one location.
Signed-off-by: Jouni Malinen <j@w1.fi>
sta == NULL check is already done above based on category !=
WLAN_ACTION_PUBLIC, but that seems to be too complex for some static
analyzers, so avoid invalid reports by explicitly checking for this
again in the WLAN_ACTION_FT case.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous check for dl_list_len() or having an entry from the list is
sufficient, but some static analyzers cannot figure out that
dl_list_first() and dl_list_last() will return non-NULL in this type of
cases. Avoid invalid reports by explicitly checking for NULL.
Signed-off-by: Jouni Malinen <j@w1.fi>
Checking sm->pmksa is sufficient here, but that seems to be too
difficult for static analyzers to follow, so avoid false reports by
explicitly checking pmkid as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
clang scan-build does not seem to like the 'd' suffix on floating
constants and ends up reporting analyzer failures. Since this suffix
does not seem to be needed, get rid of it to clear such warnings.
Signed-off-by: Jouni Malinen <j@w1.fi>
p2p_freq_to_channel() could return an error if the GO or P2P Client
operating channel is not valid. Check for this before generating the NFC
handover message.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is not of any real use anymore with nl80211_set_channel() taking
care of channel setting operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Configure driver with the new channel parameters (mainly, HT 20/40 MHz
bandwidth changes) as part of set_ap().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the initial OBSS scans in AP mode before starting 40 MHz BSS
more robust. In addition, HT20 can be used as a backup option if none of
the scans succeed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a 2.4 GHz band AP receives a 20/40 Coexistence management frame from
a connected station with 20/40 BSS Intolerant Channel Report element
containing the channel list in which any legacy AP are detected or AP
with 40 MHz intolerant bit set in HT Cap IE is detected in the affected
range of the BSS, the BSS will be moved from 40 to 20 MHz channel width.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend the minimal HT 20/40 co-ex support to include dynamic changes
during the lifetime of the BSS. If any STA connects to a 2.4 GHz AP with
40 MHz intolerant bit set then the AP will switch to 20 MHz operating
mode.
If for a period of time specified by OBSS delay factor and OBSS scan
interval AP does not have any information about 40 MHz intolerant STAs,
the BSS is switched from HT20 to HT40 mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This provides information to allow the driver to be configured for
updated channel parameters, e.g., when dynamically changing HT20/HT40
bandwidth.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like the demangle.h from binutils-dev is not installed that
commonly anymore. Since we need only two defines from that file, replace
the header file with those defines to make it easier to build with
WPA_TRACE_BFD=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some trailing whitespace and spaces for indentation were present in the
driver wrapper and header files.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Move the definitions that depended in common.h into a separate header
file so that qca-vendor.h can be copied and used as-is in other
projects.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allocates a QCA vendor subcmd for extended statistics
functionality and also an attribute for delivering the payload
for extended statistics.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These functions are not standard and do not exist in all systems, e.g.,
variants of Android. Instead use the macros defined in common.h.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
With hidden SSID (ignore_broadcast_ssid), an IOS device trying to
connect to the AP will send a probe request with ANT == 2. If
interworking support is just compiled (not enabled), we will drop the
probe request since default ANT is 0.
Check that interworking is enabled before filtering based on ANT or
HESSID to match the behavior of code without CONFIG_INTERWORKING.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
This allows the specific SIM to be identified for authentication
purposes in multi-SIM devices. This SIM number represents the index of
the SIM slot. This SIM number shall be used for the authentication using
the respective SIM for the Wi-Fi connection to the corresponding
network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Sometimes function hostapd_is_dfs_required() returns -1 which indicates
that it was not possible to check if DFS was required. This happens for
channels from the 2.4 GHz band where DFS checking should not happen.
This can be fixed by returning DFS-not-required for mode different from
IEEE80211A and when DFS support is not available (ieee80211h not set).
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Some of the buffers used to keep a copy of PTK/TPTK/GTK in the
supplicant implementation maintained a copy of the keys longer than
necessary. Clear these buffers to zero when the key is not needed
anymore to minimize the amount of time key material is kept in memory.
Signed-off-by: Jouni Malinen <j@w1.fi>
The sample code here ended up trying to register an eloop socket with fd
== -1. This was not really ever supposed to be used, but it is now also
hitting an assert in eloop. Skip the unnecessary
eloop_register_read_sock() to avoid this.
This was causing issues for hostapd since CONFIG_L2_PACKET is not set by
default. If CONFIG_RSN_PREAUTH=y was not used for CONFIG_L2_PACKET was
not set in .config explicitly, the defaul use of l2_packet_none.c ended
up hitting the newly added assert() in eloop.
Signed-off-by: Jouni Malinen <j@w1.fi>
Rather than ignoring packets with a minimal 8-byte radiotap
header, which may occur elsewhere, tag generated (decrypted)
packets with an empty vendor namespace tag and ignore those.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update the radiotap parser to the latest version of the
http://git.sipsolutions.net/radiotap.git/ library to get
parsing for vendor namespaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was already done for the disconnect event, but
SME-in-wpa_supplicant case needs to do same with the deauth event to
avoid getting extra events during WPS disconnect-and-reconnect sequence.
This can speed up WPS processing by removing unnecessary failures or
retries due to the extra event being processed during the next
association attempt.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows external programs to monitor driver signal change events
through wpa_supplicant when bgscan is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The first combination may allow single-channel concurrency for
P2P + managed, but there may be others that allow multi-channel
concurrency. Parse all of them to find the maximum number of channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
wpa_supplicant now retries for P2P_GO_NEG_CNF_MAX_RETRY_COUNT times if
it doesn't receive acknowledgement for GO Negotiation Confirmation
frame. Currently, P2P_GO_NEG_CNF_MAX_RETRY_COUNT is set to 1.
While this is not strictly speaking following the P2P specification,
this can improve robustness of GO Negotiation in environments with
interference and also with peer devices that do not behave properly
(e.g., by not remaining awake on the negotiation channel through the
full GO Negotiation).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
NL80211_CMD_LEAVE_IBSS was used only with wpa_supplicant-based SME.
Extend this to drivers that implement SME internally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Some OpenSSL versions have vulnerability in TLS heartbeat request
processing. Check the processed message to determine if the attack has
been used and if so, do not send the response to the peer. This does not
prevent the buffer read overflow within OpenSSL, but this prevents the
attacker from receiving the information.
This change is an additional layer of protection if some yet to be
identified paths were to expose this OpenSSL vulnerability. However, the
way OpenSSL is used for EAP-TLS/TTLS/PEAP/FAST in hostapd/wpa_supplicant
was already rejecting the messages before the response goes out and as
such, this additional change is unlikely to be needed to avoid the
issue.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Only the Neighbor Report element should be included here, so verify that
the element id matches. In addition, verify that each subelement has
valid length before using the data.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the definitions match the terminology used in IEEE Std
802.11-2012 and makes it easier to understand how the HT Operation
element subfields are used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was used to fill in the "PSMP support" subfield that was defined
during P802.11n development. However, this subfield was marked reserved
in the published IEEE Std 802.11n-2009 and it is not supported by
current drivers that use hostapd for SME either. As such, there is not
much point in maintaining this field as ht_capab parameter within
hostapd either.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
QCA vendor extension is used for NAN functionality. This defines the
subcommand and attribute to address this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that WPS 2.0 support is enabled unconditionally, WEP and Shared auth
type are not allowed. This made some of the older code unused and that
can now be removed to clean up the implementation. There is still one
place where WEP is allowed for testing purposes: wpa_supplicant as
Registrar trying to configure an AP to use WEP. That is now only allowed
in CONFIG_TESTING_OPTIONS=y builds, though.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is somewhat of a corner case since there is no real point in using
so short a fragmentation threshold that it would result in this message
getting fragmented. Anyway, it is better be complete and support this
case as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
If fragmentation is used, the temporary inbuf/outbuf could have been
leaked in error cases (e.g., reaching maximum number of roundtrips).
Signed-off-by: Jouni Malinen <j@w1.fi>
"SET tdls_testing 0x800" can be used to enable a special test mode that
forces the FTIE MIC in TDLS setup messages to be incorrect.
Signed-off-by: Jouni Malinen <j@w1.fi>
Following events are now sent to ctrl_iface monitors to indicate if
credential blocks have been added, modified, or removed:
CRED-ADDED <id>
CRED-MODIFIED <id> <field>
CRED-REMOVE <id>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant and wpa_cli had already moved to allowing up to 4096 byte
buffer size to be used for control interface commands. This was limited
by the line edit buffer in interactive mode. Increase that limit to
match the other buffers to avoid artificially truncating long commands.
Signed-off-by: Jouni Malinen <j@w1.fi>
"user" MACACL "password" style lines in the eap_user file can now be
used to configured user entries for RADIUS-based MAC ACL.
Signed-off-by: Jouni Malinen <j@w1.fi>
p2p_dev_addr was not NULL, so the all zeros case was printed as well.
Clean this up by printing p2p_dev_addr in debug prints only if it is a
real P2P Device Address.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add support of vendor command to hostapd ctrl_iface.
Vendor command's format:
VENDOR <vendor id> <sub command id> [<hex formatted data>]
The 3rd argument will be converted to binary data and then passed as
argument to the sub command.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When primary and secondary channel were switched and config was
reloaded, secondary channel was incorrectly overwritten.
Proceed as for other settings that should not be changed and don't
allow to overwrite.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct the
VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the presence
of the respective IEs in the received TDLS Setup Response frame.
The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When hostapd choose to reuse an existing interface, it does not add it
to the set of interfaces from which we accept EAPOL packets.
Make sure we always add it to that set.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
This allows drivers that build the WPA/RSN IEs internally to use similar
design for building the OSEN IE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is not much point in building devices with WPS 1.0 only supported
nowadays. As such, there is not sufficient justification for maintaining
extra complexity for the CONFIG_WPS2 build option either. Remove this by
enabling WSC 2.0 support unconditionally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Scan for GO on the negotiated operating channel for few iterations
before searching on all the supported channels during persistent group
reinvocation. In addition, use the already known SSID of the group in
the scans. These optimizations reduce group formation time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Especially when multiple BSSes are used with ACS, number of the error
paths were not cleaning up driver initialization properly. This could
result in using freed memory and crashing the process if ACS failed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the PMK-R1 needs to be pulled for the R0KH, the previous
implementation ended up rejecting the over-the-air authentication and
over-the-DS action frame unnecessarily while waiting for the RRB
response. Improve this by postponing the Authentication/Action frame
response until the pull response is received.
Signed-off-by: Jouni Malinen <j@w1.fi>
This moves some of the p2p_prepare_channel_best() functionality into
separate helper functions to make the implementation easier to read.
Signed-off-by: Jouni Malinen <j@w1.fi>
The main WPS code rejects WEP parameters, so this code is not used and
can be commented out from WPS 2.0 builds. This is similar to the earlier
commit that commented out in-memory update.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 94b84bc725 missed one path where
p2p->op_reg_class should have been updated. Set this to 81 during
operating channel selection from 2.4 GHz.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver supports full offloading of DFS operations, do not disable
a channel marked for radar detection. The driver will handle the needed
operations for such channels.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This uses a QCA vendor extension to determine if the driver supports
fully offloaded DFS operations.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The main WPS code rejects WEP parameters, so this code is not used and
can be commented out from WPS 2.0 builds.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not select pre-configured channel as operating channel preference if
it is unavailable maybe due to interference or possible known
co-existence constraints, and try to select random available channel.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There was possibility that the current channel in Beacon information
element was incorrectly set. This problem was easily observed when
primary and secondary channel were switched and then some of hostapd
settings (for example password) were changed using WPS External
Registrar. This caused hostapd_reload_config() function overwrite the
current channel information from config file.
This patch prevents this situation and does not allow to overwrite
channel and some other settings when config is reloaded.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
It was possible for hapd->wps_beacon_ie and hapd->wps_probe_resp_ie to
be set if WPS initialization in hostapd failed after having set these
parameters (e.g., during UPnP configuration). In addition, many of the
other WPS configuration parameters that were allocated during the first
part of the initialization were not properly freed on error paths.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While the device itself may support WPA/WPA2-Enterprise, enrollment of
credentials for EAP authentication is not supported through WPS. As
such, there is no need to claim support for these capabilities within
WPS information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The scan_for_auth workaround for cfg80211 missing a BSS entry for the
target BSS during authentication uses a single channel scan controlled
within driver_nl80211.c. This operation does not indicate
EVENT_SCAN_RESULTS to the upper layer code. However, it did report
EVENT_SCAN_STARTED and this resulted in the radio work protection code
assuming that an external program triggered a scan, but that scan never
completed. This resulted in all new radio work items getting stuck
waiting for this scan to complete.
Fix this by handling the scan_for_auth situation consistently within
driver_nl80211.c by filtering both the EVENT_SCAN_STARTED and
EVENT_SCAN_RESULTS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not truncate CURLINFO entries on first linefeed to get full IN/OUT
headers and data into debug log. Use wpa_hexdump_ascii() if any
non-displayable characters are included. Remove the separate header/data
debug dumps since all that information is now available from the debug
callback.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
These were previous set to 3.0 and 1.5 ms which ended up using values 93
and 46 in 36 usec inits. However, the default values for these are
actually defined as 3.008 ms and 1.504 ms (94/47) and those values are
also listed in the hostapd.conf example.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
test-tls-4: Short 511-bit RSA-DHE prime
test-tls-5: Short 767-bit RSA-DHE prime
test-tls-6: Bogus RSA-DHE "prime" 15
test-tls-7: Very short 58-bit RSA-DHE prime in a long container
test-tls-8: Non-prime as RSA-DHE prime
Signed-off-by: Jouni Malinen <j@w1.fi>
The center segment0 calculation for VHT20 ACS was incorrect. This caused
ACS to fail with: "Could not set channel for kernel driver".
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Secondary channel was compared incorrectly (-4/4 vs. actual channel
number) which broke matching neighboring 40 MHz BSSes and only the
no-beacons-on-secondary-channel rule was applied in practice. Once
sec_chan was fixed, this triggered another issue in this function where
both rules to switch pri/sec channels could end up getting applied in a
way that effectively canceled the switch.
Signed-off-by: Jouni Malinen <j@w1.fi>
previous_ap and last_assoc_req were not really used for anything
meaninful, so get rid of them to reduce the size of per-STA memory
allocation.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the control interface and some of the BSS setup to
be left partially initialized in failure cases while the BSS structures
were still freed. Fix this by properly cleaning up anything that may
have passed initialization successfully before freeing memory.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows hostapd to set a different management group cipher than the
previously hardcoded default BIP (AES-128-CMAC). The new configuration
file parameter group_mgmt_cipher can be set to BIP-GMAC-128,
BIP-GMAC-256, or BIP-CMAC-256 to select one of the ciphers defined in
IEEE Std 802.11ac-2013.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
For some client OBSS implementations that are performed in
firmware, all OBSS parameters need to be set to valid values.
Do this, as well as supplying the "20/40 Coex Mgmt Support"
flag in the extended capabilities IE.
Signed-hostap: Paul Stewart <pstew@chromium.org>
The 802.11ac amendment specifies that that the center segment 0 field
is reserved, so it should be zero. Hostapd previously required it to
be set, which is likely a good idea for interoperability, but allow it
to be unset. However, don't allow it to be set to a random value, only
allow zero and the correct channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some of the remote ANQP server concepts were introduces into gas_serv.c,
but these were not completed. Remote the unused implementation for now.
It can be added back if support for remote ANQP server is added at some
point.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When wpa_psk_file is used instead of wpa_psk/wpa_passphrase, each WPS
Enrollee was given a unique PSK. This did not work for the
station-as-Registrar case where ER would learn the current AP settings
instead of enrolling itself (i.e., when using the AP PIN instead of
station PIN). That case can be covered with a similar design, so
generate a per-device PSK when building M7 as an AP in wpa_psk_file
configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hostapd DEAUTHENTICATE and DISASSOCIATE control interface commands
accepted both a test=<0/1> and reason=<val> parameters, but these were
not supported in the same command as a combination. Move the code around
a bit to allow that as well since it can be helpful for automated test
scripts.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
TDLS Setup Request/Response frames from the peers include the WMM IE,
hence parse the same and consider the QoS Info from the WMM IE. The
qos_info obtained in the WMM IE overwrites the one obtained through
WLAN_EID_QOS attribute.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
p2p_find removes P2P_DEV_REPORTED flag from every existing P2P peer
entry. Thus, if a GO Negotiation Request frame is received before the
peer is re-discovered based on Probe Response frame, report
P2P-DEVICE-FOUND indication prior to the P2P-GO-NEG-REQUEST similarly to
how this is done the first time the peer is found.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, some of the last initialization steps could fail without
clearly marking the interface disabled. For example, configuring the
channel to the driver could fail, but hostapd would not clearly identify
as the interface not being in functional state apart from not moving it
to the ENABLED state. Send an AP-DISABLED event and mark interface state
DISABLED if such a setup operation fails.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This hs20-osu-client client command can be used to parse a DER encoded
X.509v3 certificate with the logotype extensions and
id-wfa-hotspot-friendlyName values shown in detail.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If NL80211_CMD_AUTHENTICATE fails due to exiting authentication, forced
deauthentication is used to clear cfg80211 start and a new
authentication command is retried. This resulted in an extra
disconnection event getting delivered to the core wpa_supplicant code
and that could end up confusing state there, e.g., by clearing
connection parameters like wpa_s->key_mgmt and preventing the following
association from reaching proper COMPLETED state with open networks.
Fix this by hiding the unnecessary disconnection event when using the
deauth-for-auth workaround.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
On RF-kill, we should not request the kernel to start a P2P device. In
addition, we should call i802_set_iface_flags() both for a P2P Device
interface and any other interface instead of calling a dedicated
function for each.
Signed-off-by: Moshe Benji <Moshe.Benji@intel.com>
At least in nl80211, broadcast management frames like Probe Request
frames, may be processed multiple times per BSS if multi-BSS is active
and NL80211_CMD_FRAME event is used to deliver them. In the case of
Probe Request frames, hostapd will create multiple redundant Probe
Response frames which are problematic when many BSS are on one channel.
This problem is caused by driver_nl80211 generating an event for
wpa_supplicant_event() for each BSS, and hostapd_mgmt_rx() calls
ieee802_11_mgmt() for each BSS, too.
Fix this by processing broadcast events only for the BSS the driver
intended to. The behavior is not changed for drivers not setting a BSS.
Signed-hostap: Simon Wunderlich <simon@open-mesh.com>
If channels are "available", change to "usable" DFS channels as a
fallback, too. This requires CAC, but it is still better to do that
instead of stopping service completely.
Signed-hostap: Simon Wunderlich <sw@simonwunderlich.de>
If DFS channels are marked as "available", an AP can switch to them
immediately without performing CAC. Therefore, the channel selection
function should consider these channels even though these are radar
channels.
Signed-hostap: Simon Wunderlich <sw@simonwunderlich.de>
Different channels allow different transmission power, at least in ETSI
countries. Also, ETSI requires a "channel plan" for DFS operation, and
channels should be randomly choosen from these channels.
Add a channel list configuration option for users to add channels
hostapd may pick from.
Signed-hostap: Simon Wunderlich <sw@simonwunderlich.de>
Previously, EAP-SIM/AKA/AKA' did not work with number of crypto
libraries (GnuTLS, CryptoAPI, NSS) since the required FIPS 186-2 PRF
function was not implemented. This resulted in somewhat confusing error
messages since the placeholder functions were silently returning an
error. Fix this by using the internal implementation of FIP 186-2 PRF
(including internal SHA-1 implementation) with crypto libraries that do
not implement this in case EAP-SIM/AKA/AKA' is included in the build.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Incorrect PTK length was used in PMK-to-PTK derivation and the Michael
MIC TX/RX key swapping code was incorrectly executed for these ciphers
on supplicant side.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While these were already available from elsewhere in the debug log, it
is convenient to have the values also available at the location where
the actual nl80211 command is issued.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The internal TLS server implementation and RADIUS server implementation
in hostapd can be configured to allow EAP clients to be tested to
perform TLS validation steps correctly. This functionality is not
included in the default build; CONFIG_TESTING_OPTIONS=y in
hostapd/.config can be used to enable this.
When enabled, the RADIUS server will configure special TLS test modes
based on the received User-Name attribute value in this format:
<user>@test-tls-<id>.<rest-of-realm>. For example,
anonymous@test-tls-1.example.com. When this special format is used, TLS
test modes are enabled. For other cases, the RADIUS server works
normally.
The following TLS test cases are enabled in this commit:
1 - break verify_data in the server Finished message
2 - break signed_params hash in ServerKeyExchange
3 - break Signature in ServerKeyExchange
Correctly behaving TLS client must abort connection if any of these
failures is detected and as such, shall not transmit continue the
session.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows the internal TLS implementation to write log entries to the
same authlog with rest of the RADIUS server and EAP server
functionality.
Signed-off-by: Jouni Malinen <j@w1.fi>
If eap_user_file is configured to point to an SQLite database, RADIUS
server code can use that database for log information.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this was silently dropped which left the connection waiting
for timeout. decrypt_error alert can be used here to avoid that.
Signed-off-by: Jouni Malinen <j@w1.fi>
This same design is used in both the server and the client roles in the
internal TLS implementation. Instead of duplicated implementation, use a
helper function.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of separate server and client side implementations, use a common
set of helper functions for calculating the ServerParams hash for
ServerKeyExchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
The SHA256-based RSA-AES-128/256 cipher suites were already implemented
and enabled for the internal TLS client, but they had not been enabled
for the server.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, this was enabled only at msgdump verbosity level, but any
level that is more verbose than it should also be included.
Signed-off-by: Jouni Malinen <j@w1.fi>
This reverts commit 4345fe963e. That
introduced number of memory leaks and since the rest of the VLAN changes
did not yet go in, it is easier to revert this for now and bring back
the changes after fixes if there is sufficient interest for them in the
future.
Signed-off-by: Jouni Malinen <j@w1.fi>
This extends the design already available for Access-Request packets to
the RADIUS server and Access-Accept messages. Each user entry can be
configured to add arbitrary RADIUS attributes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Request the driver to send a Deauthentication frame before doing
any other disconnection steps on the session timeout path. This is
needed when PMF is negotiated for the association since the driver
will need to find the STA entry and the PTK for it to be able to
protect the robust Deauthentication frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In case of Automatic Channel Selection (ACS) failure, we do not have a
real fallback path. Interface still remains in ACS state. To reflect we
did not succeed with ACS, simply disable the interface and indicate this
to user/upper layer entity so that a suitable recovery or error
notification can be performed.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
wpa_supplicant already allowed beacon interval to be configured for AP
mode operations, but this was not passed to the driver for IBSS even
though the same parameter can used for that case. Add this for the
nl80211 driver interface to allow beacon interval to be controlled for
IBSS as well.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
handle_assoc_cb() got this addition, but the check in
hostapd_new_assoc_sta() was not modified to be aware of the OSEN special
case for EAPOL state machines to be used for marking a STA authorized.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was done in handle_assoc_cb() in ieee802_11.c for drivers that use
hostapd SME/MLME. However, drivers that include SME/MLME implementation
do not use that function and the STA flag needs to be set when
processing the association notification. This is needed to get the STA
entry into showing the proper authorized state and to get the
AP-STA-CONNECTED/DISCONNECTED events on the control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
As per IEEE Std 802.11ac-2013, 'Maximum A-MPDU Length Exponent' field
value is in the range of 0 to 7. Previous implementation assumed EXP0 to
be the maximum length (bits 23, 24 and 25 set) what is incorrect.
This patch adds options to set it up within the 0 to 7 range.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
For example, the previous implementation considered [44, 48, 52, 56] to
be a valid VHT80 channel -- which it is not. This resulted in, e.g.,
failure to start CAC when channels on overlapped segments included DFS
channels.
Add a check similar to the HT40 one to prevent that. The check is
performed this way as the ACS implementation assumes the primary channel
to be the first channel in a given segment.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Previously, we printed this message as a debug one, which was confusing
in case verbose debug messages were disabled. User could think CAC
started but never ended. Add more parameterss to DFS_EVENT_CAC_START, so
external programs can more easily check what was wrong in case of
errors.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This commit adds an option to optimize AP teardown by leaving the
deletion of keys (including group keys) and stations to the driver.
This optimization option should be used if the driver supports stations
and keys removal when stopping an AP.
For example, the optimization option will always be used for cfg80211
drivers since cfg80211 shall always remove stations and keys when
stopping an AP (in order to support cases where the AP is disabled
without the knowledge of wpa_supplicant/hostapd).
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Previously, both this and combination of OUI_WFA and P2P_OUI_TYPE were
used. Using the full 32-bit value as a single operation saves a bit in
code size, so start moving towards using it more consistently when
writing or finding the P2P vendor specific element.
Signed-off-by: Rahul Jain <rahul.jain@samsung.com>
CONFIG_TESTING_OPTIONS=y build of wpa_supplicant now allows arbitrary
cfg80211 commands to be performed through the new VENDOR ctrl_iface
command by using a special vendor_id ffffffff. The command identifier
(NL80211_CMD_*) is encoded as the subcmd and the attributes in the
hexformatted data area. Response attributes are returned as a hexdump.
For example, this shows a NL80211_CMD_FRAME and a response (cookie
attribute) on a little endian host:
wpa_cli -i wlan0 vendor ffffffff 59 080003004d0000000800260085090000....
0c00580000d7868c0388ffff
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When an interface is disabled through rtm event, wpa_supplicant's
EVENT_INTERFACE_DISABLED is generated, which in turn, may
completely destroy wpa_driver_nl80211_data struct (drv). This
scenario happens now when P2P GO interface is disabled. Since this
struct may be used later in this function it causes segmentation fault.
Fix it by trying to find drv again in the interface list after
wpa_supplicant's event handling.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add a callback to the driver interface that allows vendor specific
commands to be sent. In addition, a control interface command is added
to expose this new interface outside wpa_supplicant:
Vendor command's format:
VENDOR <vendor id> <sub command id> [<hex formatted data>]
The 3rd argument will be converted to binary data and then passed as
argument to the sub command.
This interface is driver independent, but for now, this is only
implemented for the nl80211 driver interface using the cfg80211 vendor
commands.
Signed-off-by: Beni Lev <beni.lev@intel.com>
wpa_driver_nl80211_if_remove() checks bss->if_added before deleting an
interface, which is 0 for the first BSS. The only part of
wpa_driver_nl80211_if_remove() that should get called for WDS STA
interfaces is the call to nl80211_remove_iface(), which can be pulled in
here directly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
There is no need to use a for loop here since the h variable is
set identically at the beginning of the body anyway.
Signed-off-by: Jouni Malinen <j@w1.fi>
The following if statements set the new_op_mode value in all cases,
so there is no need to initialize this to 0 first. This removes a
static analyzer warning.
Signed-off-by: Jouni Malinen <j@w1.fi>
The pos variable was not used between its first and second assignment.
Clean this up by using the pos variables instead of the buf (start of
the buffer).
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to maintain a separate counter for this in addition to
the pointer to the current location. In addition, this gets rid of
warnings about unused variable write.
Signed-off-by: Jouni Malinen <j@w1.fi>
If hapd_iface->bss[i] == NULL, this could have resulted in NULL pointer
dereference in the debug print. Avoid this by skipping the message in
case of NULL pointer. In addition, clear iface->bss[i] to NULL for
additional robustness even though this array gets freed immediately.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was previously checked through the eap_peer_tls_ssl_init() call
which made it difficult for static analyzers. Add an explicit check for
config == NULL into the beginnign of eap_fast_init() since this will
always result in initialization failing anyway.
Signed-off-by: Jouni Malinen <j@w1.fi>
If wpa_driver_roboswitch_read() fails before such comparison, the values
that are being compared are not initialized properly and as such, there
is not much point in comparing them either.
Signed-off-by: Jouni Malinen <j@w1.fi>
This seemed to be fine on most code paths, but the code was complex
enough to make the analysis difficult (and a bit too much for static
analyzers). There is no harm in forcing these parameters to be
initialized, so do that to make sure they cannot be left uninitialized.
Signed-off-by: Jouni Malinen <j@w1.fi>
bfd_demangle() call could be skipped if data.function == NULL. Make sure
the already freed aname pointer cannot be used again in such a case.
Signed-off-by: Jouni Malinen <j@w1.fi>
record->type == NULL case was handled through the record->type_length
comparison. While this was correct, it is a bit difficult for static
analyzers to understand, so add an extra check for NULL to avoid false
reports on this.
Signed-off-by: Jouni Malinen <j@w1.fi>
no_offchannel_tx=1 driver parameter can now be used to force the older
remain-on-channel -based offchannel TX design to be used with
mac80211_hwsim. This can be used to increase test coverage with the
hwsim test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the error path to try to use P2P Group ID attribute
even if one was not included in the message. This could result in
dereferencing a NULL pointer, so re-check the pointer before copying the
data.
Signed-off-by: Jouni Malinen <j@w1.fi>
The special case of non-zero status code used in a GAS Comeback Response
frame to indicate that additional delay is needed before the response is
available was not working properly. This case needs to allow the status
code check to be bypassed for the comeback case prior to having received
any response data.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like leaving behind the freed pointed at the end of the array
could end up in a crash triggered by double free in some cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
PD Response is sent out using a 200 ms offchannel wait, but that wait
was not cancelled on TX status report. This could result in offchannel
operation being left waiting unnecessarily long. Fix this by making the
P2P_NO_PENDING_ACTION case in Action TX callback cancel the wait if a
pending wait is marked (and mark this for PD Response).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like some deployed devices may send an invalid supported
operating class element (length = 0) in TDLS Setup messages. With
cfg80211, this results in the NL80211_CMD_SET_STATION command failing
due to an invalid argument (cfg80211 mandates supported operating
classes information to have a length of 2..253 octets).
Work around this interop issue by ignoring the Supported Operating Class
element if it has invalid length.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new hostapd.conf parameter subscr_remediation_url can be used to
define the URL of the Subscription Remediation Server that will be added
in a WFA VSA to Access-Accept message if the SQLite user database
indicates that the user need subscription remediation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
