It was possible for dev[2] to be left with non-default config_methods
parameter at the end of the test case and that could result issues in
following test cases. This hit a failure in the following sequence:
wpas_ctrl_set_wps_params p2ps_channel_active_go_and_station_same
Signed-off-by: Jouni Malinen <j@w1.fi>
Due to a typo in a function name, this test case ended up running
without the final cleanup. That could result in the following test cases
failing, e.g., when running this sequence:
wifi_display_parsing dbus_p2p_go_neg_auth
Signed-off-by: Jouni Malinen <j@w1.fi>
The previously used invalid values will become allowed with the
following commits, so change the test case to use values that both were
and will continue to be invalid to avoid unnecessary failures.
Signed-off-by: Jouni Malinen <j@w1.fi>
autogo_scan verifies the special case where a Probe Response frame
without P2P IE has been received from a GO (e.g., due to a non-P2P
interface requesting a scan) and P2P information from a Beacon frame
needs to be used instead to determine that the group is persistent.
Signed-off-by: Jouni Malinen <j@w1.fi>
SAVE_CONFIG command on the global control interface tries to save
the config file on all interfaces. The test disabled updating the
config file only on one interface, thus for configurations that
support a dedicated P2P Device interface, saving the config file
would still have succeeded on the P2P Device interface.
Fix the test by disabling updating the configuration file on the global
control interface (which will, in practice, disable this for the P2P
Device interface) in addition to disabling it on the main interface.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
mac80211_hwsim only supports 2 different MAC addresses.
Configurations that use a dedicated P2P Device interface already
use these 2 addresses, so adding another interface on the same
PHY results in a duplicated MAC address.
Fix this by changing the MAC address of the added interface to make
sure the new interface has a unique MAC address.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Set the bridge ageing to 1 sec to make the bridge clear unused
addresses after this interval. Otherwise the test depends on
the local configuration of brctl.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Write the main interface address to the tkip_mic_test debugfs file
to generate Michael MIC failure event (which is different than the
p2p_dev_addr when a dedicated P2P Device interface is used).
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
These test cases verify behavior with parallel scan operations while
going through GO Negotiation and duplicated GO Negotiation Request frame
RX with not-yet-ready sequence in GO Negotiation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
send_iface_detach_request() can fail and that resulted in skipping a
call to restore_reg_domain() and leaving unexpected country
configuration for following test cases. This could result in failures,
e.g., in this sequence: fst_proto wpas_mesh_open_5ghz
Fix this by ignoring exceptions from send_iface_detach_request() and
continuing to restore regulatory domain.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
I modified this test case for commit
eabf083984 ('tests: P2PS channel
handling') to use dev[2] instead of dev[0], but forgot to update the
p2ps_connect_p2ps_method() dev list to match that. Fix this to actually
use a concurrent connection.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the dbus_interface test case to leave the P2P
channel lists with 5 GHz channels enabled due to the special driver=none
case. This could make the following P2P test case fail due to selecting
an unexpected channel. Fix this by forcing P2P channel list update at
the end of the dbus_interface test case.
This was triggering with the following hwsim test case sequence:
dbus_interface p2ps_connect_adv_go_p2ps_method_group_iface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use a dynamic HWSimRadio in p2ps_channel_sta_connected_disallow_freq_mcc
to allow MCC test case to be executed in default setting (MCC disabled
for the default radios).
Signed-off-by: Jouni Malinen <j@w1.fi>
Stop the pending P2P_LISTEN operation priot to issuing P2P_GROUP_ADD to
start a GO. This avoids excessively long wait for the previous Listen
step to complete before being able to start the GO. This makes
p2ps_connect_adv_go_persistent take significantly less time.
Signed-off-by: Jouni Malinen <j@w1.fi>
The combination of starting P2P extended listen and issuing
P2P_ASP_PROVISION_RESP almost immediately after that while in P2P_LISTEN
state resulted in caes where the advertiser could end up going back to a
long listen state while trying to retransmit PD Request. This resulted
in p2ps_provision() timing out while waiting for P2PS-PROV-DONE
especially in p2ps_feature_capability_* test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify OCSP stapling response that is signed by the CA rather than a
separate OCSP responder. In addition, verify that invalid signer
certificate (missing OCSP delegation) gets rejected.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a test case verifying deferred P2PS provision discovery when an
advertiser sends the status 11 (Fail: reject by user) in the follow-on
PD Request.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Not doing so may result in a deferred PD flow failure (currently the
hwsim tests succeeded because seeker never stopped find, spending enough
time listening, so the follow-on PD would succeed).
Fix this by calling p2p_ext_listen when the seeker receives a deferred
PD failure event. Cancel extended listening when PD is done and also
stop find when seek is done.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Check that there are no unencrypted frames when using hostapd with VLANs
and WPA before the first station connects to the VLAN.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
